FCC ID: NYOMBECBLE2106 BLUETOOTH LOW ENERGY

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/5181762.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case ESTABLISHED BY MOBASE ELECTRONICS U S E R M A N U A L BLE MODULE PAGE 1/6 SPEC NO. Contens 1. GENERAL INFORMATION 2. ELECTRICAL CHARACTERISTICS Changed the block diagram ALL 2021.01.21 K H KIM 1 0 RELEASED Rev.NO DESCRIPTION OF CHANGE REL. DATE 2019.08.07 REFERENCE Original archive

(PLM SYSTEM) ALL CHANGE PAGE SORT PREPARED 2019.08.07 C K SON REV. DATE CHECKED REV. BY APPROVED APPR OVAL K H KIM H S KIM J H LEE DSF-4-02-01A-1 SEOYON ELECTRONICS CO., LTD. A4(210x297) Document Change History U S E R M A N U A L SPEC NO SHT/SHTS 2/6 Date Ver

. Editor Chap. Description CR#

19.08.07 0.0 C.K SON ALL REALESE U S E R M A N U A L SPEC NO SHT/SHTS 3/6 Contents list page 1. GENERAL INFORMATION ....................................................................................................................... 4 1.1. Scope of BLE MODULE ................................................................................. 4 1.2. System configulation ..................................................................................... 4 1.3. System overview ........................................................................................... 5 2. ELECTRICAL CHARACTERISTICS .................................................................... 5 2.1. Operating characteristics of BLE MODULE ........................................................ 5 2.2. Operating characteristics of PHONE ................................................................ 6 U S E R M A N U A L SPEC NO SHT/SHTS 4/6 1. GENERAL INFORMATION 1.1. Scope of BLE MODULE The BLE MODULE offers the following features Remote Keyless Entry(Auto door Lock, Unlock, Trunk release, Panic) Wireless Communication: 2.4~2.48GHz / FSK(Manchester code) / 2.4GHz CHIP antenna 9~16 Volt nominal power supply voltage 1.2. System configulation Picture 2: System Block diagram Diag-ToolUDS on CANBLE / / External modules or functionsDDMADMRSPACAN gatewayBodyCAN (HS)IBUSmart PhoneWPCTMUBLEDoor Lock/Unlock, CrankingLINIAUServer / , BLE ID, , 3G/LTENFCIAU Local CAN (HS)WPCDHLDHRDOOR Lock/UnlockCrankingUnit Assy - WRLS Communication U S E R M A N U A L SPEC NO SHT/SHTS 5/6 1.3. System overview The BLE MODULE is used radio frequency when sending RKE1 data, the PHONE is operated by distinguish the RKE command data BLE MODULE (Transmitter) is connected with mobile phone (receiver) and presses the button of mobile phone APP (Lock, Unlock, Trunk, Panic) BLE MODULE modulates data to FSK and transmits RKE data using an RF frequency(2.4~2.48GHz) PHONE(receiver) distinguish the RKE command data and transmit command after check the door, trunk state Door lock, unlock, trunk open, panic(option) function is activated Picture 3: Functional Data Flow Diagram 2. ELECTRICAL CHARACTERISTICS 2.1. Operating characteristics of BLE MODULE ITEM Rated supply voltage Operating voltage range Operating temperature range Storage temperature range Modulation Frequency Data Coding Method SPECIFICATION DC 12V DC 9 ~ 16V

- 40 ~ + 85

- 40 ~ + 85 FSK 2.4~2.48GHz Manchester code Table 1: Electrical characteristics of 2.1. BLE MODULE 1 Remote Keyless Entry BLE Session FunctionB_BLE_CMDPhoneIAUBLE_CMDBLE_LIN_TPB_Phone_CMDPhoneIAUIAU_CMDIAU_LIN_TPB_Phone_ACKB_BLE_ACK U S E R M A N U A L SPEC NO SHT/SHTS 6/6 2.2. Operating characteristics of PHONE Item Specification Rated Supply Voltage Operating Voltage Operating Temperature Max Humidity Standby Current

Table 2: Electrical characteristics of PHONE FCC Information to User This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or FCC Compliance Information : This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation television reception, which can be determined by turning the equipment off and on, the user is IMPORTANT NOTE:

encouraged to try to correct the interference by one of the following measures:

FCC RF Radiation Exposure Statement:

erent from that to which the receiver is con-

nected.

ed radio/TV technician for help. This equipment complies with FCC RF radiation environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Caution

sponsible for compliance could void the users authority to operate the equipment. English:

This device complies with Industry Canadas license-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. French:

Le pr sent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autoris e aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radio lectrique subi, m me si le brouillage est susceptible d'en compromettre le fonctionnement.

UNIT ASSY-WRLS COMMUNICATION HKMC P/N: XXXXX-XXXXX MBEC P/N : XXXXXX-XXXX LOT NO : XXX XXXX XXXX OC lev H/W Ver : XXX S/W Ver : X.XX MODEL : MBECBLE2106 KC : R-C-SCK-MBECBLE2106 FCC : NYOMBECBLE2106 IC + 3109A-MBECBLE2106 CMIIT ID: XXXXXXXXXX MOBASE ELECTRONICS COTO. //MADE IN KOREA Li)

MOBASE ELECTRONICS CO., LTD. 100, Saneop-ro 156beon-gil, Gwonseon-gu, Suwon-si, Gyeonggi-do, Korea Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046

,Industry Canada c.c. Timco Engineering, Inc. Certification Division 849 N.W. State Road 45 P.O. Box 370 Newberry, Florida 32669 USA FCC ID : NYOMBECBLE2106 To whom it may concern:

I, the undersigned, hereby authorize Technical Manager Issac Jin of MOVON TEST LAB CO., LTD

. and here after referred to as MOVON TEST LAB CO., LTD., to act on our behalf in all manners rela ting to application for equipment authorization, including signing of all documents relating to these m atters. Any and all acts carried out by Technical Manager Issac Jin of MOVON TEST LAB CO., LTD. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing MOVON TEST LAB CO., LTD. as our agent, we still recognize that we are responsible to:

a) b) c) d) comply with the relevant provisions of the certification program;

make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

MOBASE ELECTRONICS CO., LTD. 100, Saneop-ro 156beon-gil, Gwonseon-gu, Suwon-si, Gyeonggi-do, Korea e) f) g) h) i) j) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Hee tack Ryu / Project Manager MOBASE ELECTRONICS CO., LTD. REMARK:

1. This authorization letter will be sent along with your application when filing with the Certification Division. Please follow the format and type it on company letterhead and send original to us. Authorized signature must be in agreement with grantee code contact in FCC database. 2. 3.

MOBASE ELECTRONICS CO., LTD. 100, Saneop-ro 156beon-gil, Gwonseon-gu, Suwon-si, Gyeonggi-do, Korea Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC ID: NYOMBECBLE2106 To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematics / Block Diagram / Operational Description / Parts List Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days External Photos / Internal Photos / Test Setup Photos / User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondence during certification review process cannot be granted as confidential documents and such information will be available for public review once the grant of equipment authorization is issued. Sincerely Yours, Hee tack Ryu / Project Manager MOBASE ELECTRONICS CO., LTD.