ATTACHING SMARTCABLE™
FREEDOM MICRO® II HS MANUAL
1
Insert SmartCable into the charge port on the puck.
The hooks on cable should click when fully seated.
2
Plug SmartCable into the charge port of the device.
Phone should be turned ON, and unlocked
before inserting SmartCable™ while in
MTI Connect® mode.
REMOVING SMARTCABLE
1
Insert the crescent end of the Freedom Micro II tool
into the opening to the right of the LED. Twist the
Freedom Micro II tool clockwise 45 degrees and hold
it in place.
2
Twist the device and bracket off of the position.
3
Remove the SmartCable from the puck.
4
The loose cable can be clipped into SpeedBracket™
for easy storage.
www.MTIGS.com | T:800.426.6844
MTI P/N 063-00341 rev A ©2021 MTI All Rights Reserved
10
RFID COMMANDS
FREEDOM MICRO® II HS MANUAL
Default Mode
Enter Standard Mode
AUTHORIZATION
Double Beep
Program User Card
Exit Programming Mode
V
E
R
S
A
K
E
Y
™
V
E
R
S
A
K
E
Y
™
Flash White every 8 seconds:
Disarmed
AUTHORIZATION
Double Beep
Double Beep
Auto time out if no user cards are
added, reverts to Default mode.
Arm/Disarm Position
Set Lockdown/Unlock While Armed
Solid White:
Armed
Double Beep: Accepted
Four Fast Beeps: Rejected
Flash White every 8 seconds:
Disarmed
Tap and Hold Access Card for 10
seconds. It will double beep immediately,
and double beep again after 10 seconds.
Position will automatically lock down
when armed, and unlock when disarmed
when in Lockdown mode.
V
E
R
S
A
K
E
Y
™
Double Beep:
Accepted
Four Fast Beeps:
Rejected
Solid White:
Armed - Locked
Flash White Every 8
Seconds:
Disarmed - Automatically
unlocks
www.MTIGS.com | T:800.426.6844
MTI P/N 063-00341 rev A ©2021 MTI All Rights Reserved
11
RFID MTI CONNECT PAIRING
FREEDOM MICRO® II HS MANUAL
Default Mode
Enable Pairing Mode on MTI Connect Hub
Insert MTI Connect® IntelliKey™
for 10 seconds.
Network
tattatm Stataatuaa
System Status
Power
Reset
Enter Network Mode
Position connects successfully
to mesh network:
Position fails to connect to mesh
network within 3 minutes:
V
E
R
S
A
K
E
Y
™
NETWORK PAIRING
Slow Beeps
Double Beep
Four Fast Reject Beeps
www.MTIGS.com | T:800.426.6844
MTI P/N 063-00341 rev A ©2021 MTI All Rights Reserved
12
LED STATUS INDICATORS
FREEDOM MICRO® II HS MANUAL
Visual Reference
System Status
Condition
Solid White
Puck is armed and docked.
Single white flash every 5 seconds
Puck is armed and lifted.
Double white flash every 8 seconds
Puck is docked, but not armed, puck is
connected to a mesh network.
Flashing Red and White with audible alarm
Alarm has been triggered. silence the alarm
and inspect the tether, puck trigger, and base
trigger.
Flashing Red and White with no audible
alarm
Puck is in silent alarm mode. The audible
alarm has exceeded 5 minutes and the
position is unable re-arm itself. inspect the
tether, puck trigger, and base trigger before
attempting to arm the puck.
Solid Yellow
Puck is armed, docked, but has lost it’s
network connection. Ensure the puck is
within range of the MTI Connect® Hub. Try
network pairing again.
*Only applicable when the puck is being
used with the MTI Wireless Network.
www.MTIGS.com | T:800.426.6844
MTI P/N 063-00341 rev A ©2021 MTI All Rights Reserved
13
LED STATUS INDICATORS
FREEDOM MICRO® II HS MANUAL
Visual Reference
System Status
Condition
Flashing Yellow Every 5 Seconds
Puck is armed, lifted, puck is NOT connected
to a mesh network. Only applicable in
Network Mode.
Solid Blue
After tapping an authorization card: The
puck is in enrollment mode. Tap VersaKey™
to authorize them for use in standard mode.
Enrollment mode closes automatically in 3
minutes.
In normal use: Overcurrent in charging circuit
– most likely a problem in the SmartCable™.
Flashing Blue
Puck has entered network pairing mode.
Stops upon successful pairing, or after 90
seconds.
Single Red Flash
TO BE VERIFIED: Only follows an attempt to
arm the puck. Occurs when the puck cannot
arm, for example, due to a released trigger
but the user attempts to arm the puck with
the app or key.
Multi-colored flash
Puck has received an “identify” command
from a user of the MTI Connect® software.
Flashing Green
www.MTIGS.com | T:800.426.6844
Puck is disarmed in factory default mode.
Complete the setup for Standard or Network
mode to use VersaKey™ or MTI Connect®.
Note: The puck may automatically arm while
in this default mode, as long as all triggers
are closed for 15 minutes. Once it arms, the
LED will turn solid white.
MTI P/N 063-00341 rev A ©2021 MTI All Rights Reserved
14
RISER DIMENSIONS
FREEDOM MICRO® II HS MANUAL
4.36”
2.74”
2.05”
PUCK DIMENSIONS
1.85”
60°60°
4.38”
3.45”
1.84”
1.28”
1.85”
www.MTIGS.com | T:800.426.6844
MTI P/N 063-00341 rev A ©2021 MTI All Rights Reserved
15
RISER WITH ADAPTER DIMENSIONS
FREEDOM MICRO® II HS MANUAL
4.36”
2.74”
3.45”
60°60°
Slot Adapter shown.
Through-hole adapter is
identical in size/ appearance
minus these tabs.
1.89”
4.38”
2.80”
1.84”
www.MTIGS.com | T:800.426.6844
MTI P/N 063-00341 rev A ©2021 MTI All Rights Reserved
16
BRACKET DIMENSIONS
FREEDOM MICRO® II HS MANUAL
MAXIMUM: 180mm H x 90mm W
MINIMUM: 118mm H x 65mm W
1.11”
Accomodates Phones
7-9mm Thick
www.MTIGS.com | T:800.426.6844
MTI P/N 063-00341 rev A ©2021 MTI All Rights Reserved
17
FCC AND ISED STATEMENT
FREEDOM MICRO® II HS MANUAL
FCC ID: 2AA2X-15000282
Model: ROUND FREEDOM MICRO II HS
FCC Statement
This device complies with Part 15 of the FCC Rules.
Caution: If any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could
void the user’s authority to operate the equipment.
The RF Exposure Compliance distance is 20 millimeters.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
ISED Certification Number: 24439-15000282
Model: ROUND FREEDOM MICRO II HS
ISED Statement
This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
CAN ICES-3(B)/NMB-3(B)
CAN ICES-3(B)/NMB-3(B)
Le présent appareil est conforme aux CNR Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes:
(1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage
est susceptible de compromettre le fomctionnement du dispositif.
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain
Canadian information on RF exposure and compliance.
Le dispositif rencontre l’exemption des limites courantes d’évaluation dans la section 2.5 de RSS 102 et la conformité à l’exposition de RSS-102 rf,
utilisateurs peut obtenir l’information canadienne sur l’exposition et la conformité de rf.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated
with a minimum distance of 20 millimeters between the radiator and your body.
Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu’aucune autre antenne ou émetteur. Cet équipement devrait être installé et
actionné avec une distance minimum de 20 millimètres entre le radiateur et votre corps.
Technical Data
Operating Temperature:
Operating Frequency:
Max Power:
0°C to 40°C
2405 MHz to 2480 MHz
Less than 4 dBm at 2.4 GHz
Operating Frequency:
125kHz
Max Power:
Less than 20 dBuA/m at 3m
This product contains a rechargable battery. Proper storage, use, and
disposal of the battery is important. Please refer to the guidelines below:
Additional Safety Information
1.
2. No user replaceable parts inside; refer servicing to manufacturer or
For indoor use only. The apparatus shall not be exposed to water.
qualified service personnel.
Only use accessories specified by the manufacturer.
Do not expose to excessive heat sources.
3.
4.
i.
ii.
Properly dispose of the battery; Do not dispose
of the battery into a furnace/oven or into a fire or
mechanically crush or cut the battery, as this could
cause the battery to explode.
Storing the battery in an environment at higher
temperatures than stated above can result in
explosion or leaking of flammable liquid or gas.
Disposal: All electrical and electronic products including batteries should
be disposed of separately from the municipal waste stream via designated
collection facilities appointed by the government or the local authorities.
iii. Subjecting a battery to very low air pressure or
high altitudes can result in explosion or leaking of
flammable liquid or gas.
www.MTIGS.com | T:800.426.6844
MTI P/N 063-00341 rev A ©2021 MTI All Rights Reserved
18