C4D-4G4USAA_V6+ - INSTALLATION GUIDE V 1.0 05/09/2018 Table of contents Preface ....................................................................................................................................... 3 Warnings and notices ............................................................................................................... 3 FCC Regulations ........................................................................................................................ 3 FCC RF Exposure Information .................................................................................................. 4 1. Hardware features ................................................................................................................. 5 2. Hardware description ........................................................................................................... 6 2.1. External view ................................................................................................................... 6 2.2. Internal view ................................................................................................................... 6 2.3 OBD connector pin out .................................................................................................. 7 Please read warnings section at the beginning of the installation guide............................ 7 2.4 OBD adapter wires ......................................................................................................... 7 3. Preparing/installing the device ............................................................................................ 8 3.1. Open the device ............................................................................................................. 8 3.2. Insert/remove the SIM card .......................................................................................... 9 Once inserted the SIM card looks like this: ........................................................................ 9 3.3. Properly close the device ......................................................................................... 10 3.3. Install the OBD Dongle ................................................................................................ 12 4. LED sequences .................................................................................................................... 12 5. Support ................................................................................................................................ 12 Preface The information contained in this installation guide is subject to changes in order to improve the reliability, design or features without prior notice. Mobile Devices Ingnierie reserves the right to make changes in the content without obligation to notify any person or organisation of such changes or improvements. Mobile Devices Ingnierie can in no event be held liable for technical or editorial errors or omissions herein, nor for incidental, special or consequential damages from the furnishing, performance or use of this installation guide. Please contact our technical support for current updates and supplemental information concerning the use and operation of this or other Mobile Devices Ingnierie products. Warnings and notices The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. Please read the installation guidelines, as well as the safety and operating instructions before operating your device. Follow all instructions and heed all warnings in the installation guide. There is a risk of explosion if the battery is replaced by a wrong battery type. Please discard empty battery according to local regulations. Dispose of used batteries according to the instructions. FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF Exposure Information This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the United States. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation. The FCC has granted an Equipment Authorization for this model device with all reported RF exposure levels evaluated as in compliance with the FCC RF exposure guidelines. RF exposure information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: A6GC4D-4G4USV6. 1. Hardware features OBD Dongle Performance Processor RAM NAND Flash Power supply External power supply range External voltage measurement Li-pol battery Cortex A5 - 500MHz 128 Mbytes 256 Mbytes 8-18V 270mA.h Communication Modem 4G Cat.4 ATT module (LE910-NA V2) WLAN Positioning Interface & Telematics features Environmental Modem antenna Internal Wifi Bluetooth GNSS receiver GNSS antenna USB (2.0 Host) WiFi 802.11 b/g/n 2.4G BT 4.1 LE U-blox M8 (GPS, GLONASS) Internal powered (100mA on 5V minimum) optional 3D Accelerometer 2g, 4g, 6g, 8g, 16g OBD protocols CAN interface OBD connector Connectors CAN, KWP2000, VPW, PWM Dual CAN coprocessor Multiplexed OBD OBD connector Mini USB Operating temperature Dimensions
-20C/+55C with Battery
-20C/+60C without battery With OBD connector: 27x69,5x51 mm Without OBD connector: 27x56.5x51 mm SIM card slot 2. Hardware description 2.1. External view 1 : OBD connector 2 : USB connector 3 : Status led 2.2. Internal view 4 : GNSS antenna 5 : SIM holder 6 : Internal battery*
2 1 3 2 5 4 6
* Please read warnings section at the beginning of the installation guide 2.3 OBD connector pin out Pin #
2 4 5 6 7 10 14 15 16 Comment J1850+ (PWM/VPW) Chassis ground Signal ground CAN High K line J1850- (PWM) CAN low L line Battery voltage
* Please read warnings section at the beginning of the installation guide 2.4 OBD adapter wires This adapter is only used to connect the OBD to a computer (laptop/desktop). Pin # Wire color 2 4 5 6 7 10 14 15 16 Yellow Black Grey Green Blue Violet Orange White Red 3. Preparing/installing the device 3.1. Open the device 3.2. Insert/remove the SIM card The SIM card slot is located between the two electronic cards. Once inserted the SIM card looks like this:
Insert the card with contact on bottom into the slot and push it as far as it will go. 3.3. Properly close the device First, check that the electronic card is correctly inserted in the plastic part and that usb port is correctly positioned into the casing. If its not inserted proceed as shown below. NOT GOOD NOT GOOD GOOD GOOD Second, insert the back cover beginning with the bottom. Third, insert the top cover beginning with the back and push on top to clip-on the top cover Finally, place the screw. 3.3. Install the OBD Dongle Connect the OBD Dongle on your vehicle OBD connector. 4. LED sequences The Dongle has a two-coloured LED, green and red. When both colours are brightened, you can see an orange light. Green LED Red LED Ext. Power/Run Meaning OFF Sequence Dongle OFF Meaning 3 times (50ms ON/100ms OFF) 3550ms OFF 2 times (50ms ON/100ms OFF) 3700ms OFF 1 time (50ms ON/100ms OFF) 3850ms OFF 2000ms ON 2000ms OFF Sequence No Modem
/No GNSS No Modem
/Fix GNSS Modem OK
/No GNSS Modem OK
/Fix GNSS 5. Support For all questions not related in this installation guide, please contact the support team by email at support@mobile-devices.fr Shutdown/Hibernate 30ms ON / 1 s OFF Idle/Sleep 30ms ON / 1 s OFF ON