FINGER PICK Model Name: Bluetooth LE scanner trigger Quick User Guide INTRODUCTION The purpose of the Finger Pick finger button is to turn on the barcode reader of a Honeywell Android device to be able to read barcodes while holding the device on your wrist. This way you can easily transform your hand held PDA into a wearable PDA. To work it is necessary to install the dedicated Android application. SAFETY INFORMATION Only operate the Bluetooth Finger Pick in accordance with its purpose. Do not operate or charge this product near any liquid(s). Do not use abrasives, thinners, alcohol, solvents or aerosol cleaners that may cause damage to the Bluetooth Finger Pick. If the die-cast chassis or other parts are damaged, do not touch the damaged parts. This product contains a lithium-polymer rechargeable battery, which is permanently built-in. To dispose of, be sure to comply with the laws and regulations in your country or region. Do not charge for longer than the specified time. Do not bend or drop the product, or otherwise expose it to strong physical impact. Never disassemble or modify the product. Do not expose the product to high temperatures, high humidity or direct sunlight. Specification Bluetooth LE button Operating Temp: -202 ~ 502 Approx. Weight: 20g Bluetooth version: Bluetooth V4.0 Battery: Li battery Battery life: 180 days Federal Communication Commission Interference Statement Model: FP2 FCC ID. : XTS-FP2 THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATIONS IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: ( 1 ) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND ( 2 ) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void users authority to operate the device. FCC INFORMATION The Federal Communication Commission Radio Frequency Interference Statement includes the following paragraph:
The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no grantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help. The user should not modify or change this equipment without written approval form Mobility Sound Technology LTD. Modification could void authority to use this equipment. USER MANUAL CHARGING AND BATTERY Charging of the Bluetooth Finger Pick is done via the Type-C USB connector. Use a standard USB connection or charger supporting: 5V - 1A. During charging, the LED shows a solid Red color. When the battery is fully charged, the LED either turns off. If during operation the battery level goes low the LED show a solid Red color to indicate the battery need to be recharged. With a fully charged battery, the expected operational time is above 3 months. POWER ON AND OFF To power ON the Finger Pick you have to press and hold the POWER button for 2 seconds. When powered ON Blue LED flash twice. When powered ON, Finger Pick goes in Pairing Mode for 120 seconds, after Pairing Mode is timeout, Finger Pick goes power off. To turn OFF the device you have to press and hold the power button for 2 seconds until the BLUE LED solid ON, then release power button USE ANDROID APPLICATION 1. Install the application from Google Play Store (recommended for automatic updates). Search Finger Pick Lexter on the Play Store from your Honeywell device or scan the QR code below. Alternatively use the URL below or scan the QR code below www.lexter.com/download/honeywell.apk 2. Open the installed application. The name of the app is Lexter Wearable. 3. Allow app to access devices location Pair to Honeywell device 4. Tap on Bluetooth trigger configuration 5. Allow app to turn on the bluetooth (This point only if bluetooth is not enabled) 6. Select your Finger Pick from devices list (you see the MAC ADDRESS) Widget You can add the widget on the home screen to unpair the button easily. Open the app and tap to Bluetooth unpair shortcut for add the widget Unpair it is recommended to use the widget as described above. If necessary, you can also unpair by opening the app Bluetooth trigger configuration Unpair trigger Important Note If a finger pick is connected to a device, you must first unpair it in order to connect it to another device. It is therefore recommended to use the widget to unpair the device at the end of the work. LED EVENTS Power ON Power OFF LED Turned off LED Blue LED double flash Blue LED solid ON until the power button is released FUNCTION The device is turned off or the battery charging is complete. Blue single flash (every 3 seconds) Finger Pick connected to device Blue fast double flash(every 2 seconds) Pairing Mode Red solid Battery charging or battery low