Federal Communication Commission Interference Statement typical handheld two-way radios w under mobile usage condition were certified This equipment has been tested and fo comply with the limits for a Class B digit pursuant to Part 15 of the FCC Rules. T limits are designed to provide reasonab protection against harmful interference residential installation. This equipment g uses and can radiate radio frequency en if not installed and used in accordance instructions, may cause harmful interfer radio communications. However, there i guarantee that interference will not occ particular installation. If this equipment d cause harmful interference to radio or tel reception, which can be determined by the equipment off and on, the user is en to try to correct the interference by one following measures:
ound to tal device, These ble in a generates energy and, with the rence to is no ur in a does elevision turning ncouraged e of the
(i.e. keep 20cm away from the us use of such radio closer than 20c the US RF exposure limit and shall be avoided. and shall be avoided. user body) and cm may exceed Mobility Sound BT-PTT2 PTT2 PUSH-TO-TALK USER GUIDE For use with Mobility Sound wireless Adapters (Sold Separately) eless Bluetooth The Mobility Sound BT- PTT2 allow to- Talk wirelessly over your two-
using with a Mobility Sound Adapt compatible wireless headset. ws you to Push-
- way radio when ter and a
- Reorient or relocate the receiving anten
- Increase the separation between the e and receiver.
- Connect the equipment into an outlet circuit different from that to which the re connected.
- Consult the dealer or an experienced technician for help. enna. equipment on a eceiver is radio/ TV FCC Caution: Any changes or modific expressly approved by the party respo compliance could void the user's au operate this equipment. cations not onsible for uthority to This device complies with Part 15 of the Rules. Operation is subject to the follow conditions: (1) This device may not caus interference, and (2) this device must a interference received, including interfere may cause undesired operation. e FCC wing two use harmful accept any ence that This equipment complies with FCC RF exposure limits set forth for an uncontro environment. To maintain compliance w RF exposure compliance requirements, avoid direct contact to the transmitting a during transmitting radiation olled with FCC
, please antenna RF Exposure Warning!
manual This m lies to the applie Mobility Sound Mobility Sound BT-PTT Push-
transmitter transmitter T2
-to- Talk The Mobility Sound Mobility Sound T2 works BT- PTT ll Mobility with al Sound Bluetooth Audio Adapters. Audio Mobility Sound BT Model No.: BT- PT wan Made in Taiwa T- PTT2 PTT2 All other product or service name property of their respective owne es are the ers. Please keep product 20cm away from y or bystander during the radio operation your body n. The 2014 Mobility Sound Technology Ltd,, Mobility Sound Technology Ltd,, All Rights Reserved Controls and connection Power button, long press to turn BT-PTT2 on and off. PTT button When paired with Mobility Sound Audio Adapter and headset, this button functions as a Push-to-talk, when this button is press, will cause the radio to transmit. LED indicator Messages the status of BT-PTT2 Dust cover Used to cover the USB port when BT-PTT2 is not being charged. USB Charge Port Is used to connect to power for charging Clothing Clip This 360 rotating clip can be used to secure the BT-PTT2 to users clothing or any other convenient location. QUICK START QUICK START 1. Charge the Mobility Sound BT- PTT2 PTT2 2. Pair the Mobility Sound Adapter with a wireless headset Adapter with a wireless headset 3. Pair the Mobility Sound BT- PTT2 with the 4. Test and Use. PTT2 with the Mobility Sound Audio Adapter OPTIONAL CHARGER OPTIONAL CHARGER Universal Wall Charger with Universal Wall Charger with USB interface USB interface STEP ONE: Charging the Mobility Sound Mobility Sound BT-PTT2 The Mobility Sound BT- PTT2 has an in charged prior to operation, and must more than 12 hours of operation befo nternal Lithium-ion rechargeable battery pack w be recharged regularly. A fully charged battery ore needing to be recharged. which must be should provide To charge the Mobility Sound BT-PTT2:
PTT2:
Ensure the Mobility Sound BT- PTT the device. Plug the USB charge port on the will first need to remove the prote damaging your BT- PTT2, always device). T2 is turned off, using the power button located ed on the side of bottom of the BT- PTT2 into any powered USB ective rubber dust cover. (To prevent dust and m ensure this cover is in place when you are not connector. You moisture from charging the
When charging, the LED on the B charging, the LED light will turn o The Mobility Sound BT- PTT2 takes vary depending on several factors BT- PTT2 will show a solid blue light. When the de off. es approximately 4.5 hours to charge. Actual cha s including the batterys charge state, condition,
evice is done arge time will
, and age. Charging Cautions:
Use only a POWERED USB port NOT work. Do not use a wall charger that app etc.) Do not tamper with or modify the Always turn OFF the power when for charging Non- powered ports (such as on a USB hub) will ppears to be damaged. (Example: frayed wires, melted plastic, Mobility Sound BT- PTT2 or the charger. hen charging the Mobility Sound BT- PTT2.
Pairing With an Audio Accessory STEP TWO: Pairing MOBILITYSOUND Audio Adapter, Wireless Headset, and BT-PTT2 In order to operate, the MOBILITYSOUND BT- PTT2 must be paired to a MOBILITYSOUND Adapter). However, The MOBILITYSOUND Adapter must first be paired to a wireless Bluetooth headset. To pair these devices, follow this procedure:
Pairing the MOBILITYSOUND Adapter and Bluetooth Headset
The MOBILITYSOUND Adapter (some models will need a charged battery inside) must be connected to a compatible radio. Ensure the two- way radio, Bluetooth headset, and MOBILITYSOUND BT- PTT2 are all powered off. Place the MOBILITYSOUND Adapter in Audio Accessory Pairing mode. On most adapters, this is done by holding down the PTT button on the MOBILITYSOUND Adapter first then turn on the 2-way radios power. Continue to hold the PTT button down for approximately three seconds. until the status LED flashes two times per second. The MOBILITYSOUND Adapter is now in audio accessory pairing mode. Activate the pairing mode on your Bluetooth headset by following the instructions provided by the headsets manufacturer. Once the wireless audio accessory and MOBILITYSOUND Adapter are paired with each other, the status LED on the MOBILITYSOUND Adapter will show a constant blue light for three seconds. Once the headset and MOBILITYSOUND Adapter have been successfully paired, turn off the two- way radio and Bluetooth headset and wait at least three seconds. Pairing the MOBILITYSOUND Audio Adapter and MOBILITYSOUND BT-PTT2
Holding down the PTT button on the MOBILITYSOUND Adapter then turn on the 2-way radio. Continue to hold the PTT button down for approximately three seconds. Release the PTT button when the status LED flashes two times per second. Press and release the PTT button again. The LED should now flash three times per second, indicating that the MOBILITYSOUND Audio Adapter is now in PTT pairing mode. Place the MOBILITYSOUND BT- PTT2 in pairing mode, first make sure BT-PTT2 is in power off status, then holding down the Push- To- Talk and power buttons on the side of the device simultaneously and continue to hold down both the buttons about 3 seconds until the LED indicator on the MOBILITYSOUND BT- PTT2 shows two blue flashes every second. You can then release the Push- to- Talk and power buttons. The MOBILITYSOUND BT- PTT2 is now in pairing mode.
Once the MOBILITYSOUND Audio Adapter and MOBILITYSOUND BT- PTT2 are paired with each other, the status LED on the MOBILITYSOUND Audio Adapter will show a constant blue light for three seconds and the LED on the PTT will show one blue flash every six seconds.
If the MOBILITYSOUND Audio Adapter or MOBILITYSOUND BT- PTT2 does not detect a compatible wireless accessory within 60 seconds of being put into pairing mode, the devices will exit the pairing mode and resume normal operation. After pairing is successful, turn off the MOBILITYSOUND BT- PTT2 and the two- way radio that the MOBILITYSOUND Audio Adapter is attached. Wait at least three seconds. Testing and Using the MOBILITYSOUND BT Testing and Using the BT-PTT2 STEP THREE: Testing and Using the
: Testing and Using the MOBILITYSOUND BT-PTT2
After the Bluetooth headset, MOBILITYSOUND have been paired with each oth her you can test and use them together:
MOBILITYSOUND Audio Adapter and MOBILITYSOUND MOBILITYSOUND BT- PTT2 Turn on the two- way radio which which MOBILITYSOUND Audio Adapter is connected ed to. Turn on the Bluetooth headset. MOBILITYSOUND Audio Adapt and MOBILITYSOUND Audio A
. Within a few seconds the LED indicator on the he ter should show a long flash, indicating the Blue Adapter are connected. etooth headset Turn on the MOBILITYSOUND B will flash rapidly. Within a few indicating that it is connected w BT- PTT2. The LED indicator on the MOBILITYSOUND seconds the LED indicator will show one blue fla wirelessly to the MOBILITYSOUND Audio Adapte MOBILITYSOUND BT- PTT2 ash per second, er. You will now be able to operate button on the MOBILITYSOUND Transmitted audio will be picked heard through the Bluetooth he e using the wireless accessories. Pressing the P MOBILITYSOUND BT- PTT2 will trigger the two- way radio to start ed up by the Bluetooth headset. Received signals eadsets earphone. Push- to- Talk start transmitting. ls will also be STATUS LED MESSAGES The meanings of the various LED messages shown by the MobilitySound BT-PTT2 are shown on the following table LED INDICATION No indication Two Blue flashes every second One Blue flashes every 6 seonds Continuous solid red Repeated rapid blue flash MEANING Device is powered off Pairing mode Bluetooth connected PTT button pressed Bluetooth link lost One blue flashes every second Battery low Continuous solid blue(when connected charging) Device is in charging No indication (when connected charging) Device charging completed SPECIFICATION Operating Temperature Storage Temperature Size Weight Bluetooth version Chip set Receiver sensitivity Bluetooth power class Maximum range Display SPECIFICATION
-20 to 50
-40 to 80 65mm(H) x 30mm(W) x 17mm(D) 25 grams Fully qualified Bluetooth 2.1 CSR BC5 + 16MB external flash
-82 dbm (typical) Class 2 10 meters Two-color LED Bluetooth profile support SPP(Serial Port Profile) DC input Current Draw Battery Charging type 5V DC 16mA(average), 20mA(maximum) 240mAh Lithium-ON USB Troubleshooting My MobilitySound BT-PTT2 will not pair with the MobilitySound Adapter. Follow the instructions to place the Mobility Sound Adapter into the correct pairing mode and then activate the pairing mode on the Mobility Sound BT- PTT2. Make sure that the Mobility Sound Adapter and PTT are within one meter of each other. Make sure that all other nearby Bluetooth devices are turned off. These devices can interfere with the pairing process. My Mobility Sound BT-PTT2 worked fine before, but is not working now. Ensure that your Mobility Sound BT- PTT2 has a fully charged battery and is turned on. Ensure that the Bluetooth headset is powered on and paired with the Mobility Sound Adapter. If the devices will still do not work, re- pair the Mobility Sound Adapter, Bluetooth Headset, and Mobility Sound BT- PTT. SUPPORT AND WARRANTY Mobility Sound Technology Ltd., warrants this product against defects in materials or workmanship for a period of one year from the date of retail purchase. Mobility Sound will repair or replace a defective unit, at our option, without charge for parts or labor. The limited warranty is extended only to the original purchaser. It does not cover damage or failure caused by or attributable to Acts of God, abuse, misuse, improper or abnormal usage, faulty installation, improper maintenance, lightning, or other incidences of excessive voltage, or any tampering or repairs by other than a Mobility Sound Technology Ltd authorized repair facility. It does not cover replacement of consumable parts, transportation costs, or damage in transit. Repair or replacement under the terms of this warranty does not extend the terms of this warranty. This warranty can only be modified by an officer of Mobility Sound, and then only in writing. Should this product prove defective in workmanship or material, the consumers sole remedies shall be such repair or replacement as provided by the terms of this warranty. Under no circumstances shall Mobility Sound be liable for any loss or damage, direct, consequential, or incidental, arising out of the use of or inability to use this product. Some states do not allow limitations on how long an implied warranty lasts or the exclusions or limitations of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights. For support or warranty service on your Mobility Sound product, contact us at info@mobilitysound.com or visit us on the web at ww w.m obilit ys ou nd .com COPYRIGHT AND TRADEMARK INFO 2014 Mobility Sound Technology Ltd., All rights reserved. DISCLAIMER: The Bluetooth wireless link used by Mobility Sound products is an open standard, unsecured technology. As such, it is not recommended for first- responder or other mission critical users.