FCC Compliance and Advisory Statement. LABELLING REQUIREMENTS (Part15,Section15.19(a)(3)) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1)this device may not cause harmful interference, and(2)this device must accept any interference received, including interference that may cause undesired operations. INFORMATION TO THE USER (Part 15. Section15.105(b)) INFORMATION TO THE USER This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one more of the following measures:
1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and the receiver. 3) Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. 4) Consult the dealer or an experienced radio/TV technician for help. WARNING(Part 15, Section 15.21) Any changes or modifications not expressly approved by the Jun telecom Inc. could void the user`s authority to operate the equipment. Where shielded interface cables have been provided with the product or specified additional components or accessories elsewhere defined to be used with the installation of the product, they must be used in order to ensure compliance with FCC regulations. Canadian DOC Statement. Suggested text for the notice indicating compliance with this Standard:
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada. 1 DECLARATION OF CONFORMITY Manufacturer`s Name MOBITECHPLUS INC. Manufacturer`s Address Declares, that the product Product Name 32-5 Songwol-Dong Jongno-Gu, Seoul 110-101, Korea USB PC CAMERA Model Name(Number) Confirms to the following harmonized European standards have been applied:
MW-200 EMC : EN55022 : 1998 + A1: 2000 (Class B) EN55024 : 1998 + A1: 2001 / EN61000-4-2:2001 EN61000-4-2:2001 EN61000-4-3:2001 EN61000-4-4:2001 EN61000-4-5:2001 EN61000-4-6:2001 EN61000-4-11:2001 The product herewith complies with the technical regulations within the scope of Council Directives, 89/336/EEC and 99/5/EC carries the CE mark accordingly. June ??, 2004 Seoul, Korea European Contact :
Remark : The EC declaration of conformity similar to above statements shall be provided in the accompanying instruction manual. 2 2 2 2 3 4 4 4 5 5 10 13 14 15 15 16 17 INDEX 1. Product introduction 1.1 Description 1.2 Required system conditions 1.3 Components 2. Precautions 2.1 Warnings at installation 2.2 safety instruction 3. CD Installation introduction 3.1 CD S/W Installation 3.2 Driver recognition on Windows 2000/XP 3.3 Driver recognition on Windows 98/98SE/ME 3.4 Remove software and driver 4. WebCAMeye Light Usage 4.1 Name 4.2 Focus adjustment 4.3 Adhesion of the magnetic panel 4.4 Set up the options 5. WebCAMeye Light S/W Usage 5.1 WebCAMeye Usage instruction 5.2 EyeImage Usage instruction 5.3 EyeChat Usage instruction 18 19 19 26 27 31 6. FAQ 3 1. Product introduction 1.1 Description Item Description Remark Sensor VGA(640480) 1/4 inche CMOS Sensor Pixels 320,000 Minimum illumination 1.9Lux Lens F=2.8, f=4.5, 4 element View angle 53 Focal range 2 ~
VGA(640480),CIF(352288), Window size SIF(320240),QCIF(176144), QSIF(160120) Format RGB24, I420 Frame per second 30FPS(QSIF), 30FPS(QCIF), 30FPS(SIF), 30FPS(CIF), 15FPS(VGA) Signal/Noise rate >45 Dynamic range 60 Compress format ISO/IEC 10918-1(JPEG) Automatic Control reset level control, Automatic Gain Control and Automatic Exposure, Auto White balance, Auto COMS auto/manual Histogram Equalization Interface USB 1.1 1.2 Required system conditions Item O/S Required System conditions Remark Windows 98, Windows 98SE, Windows ME, Windows 2000, Windows XP CPU Above the Pentium II 250 MEMORY Above 128M HDD 100M space (in case of installing the software) VGA Above the 80060024bit USB IBM PC or compatible with USB port 4 1.3 Components A B C A. WebCAMeye Light Main Body B. Installation CD C. Magnetic panel for adhesion 1 ea 1 ea 1 ea 5 2. Precautions 2.1 Warning on installation Must install the driver of CD before you connect the PC camera to the computer. Must install the PC camera on the plain surface firmly with magnetic panel in order for the camera not to be come off. Must get rid of dust and humidity on the surface which you install the PC camera. The problem can be caused if you use expended USB cable to connect PC & PC camera. Please be careful not to pull excessively the USB cable of PC camera since it can damage (the cable). Please don t turn flexible wire of PC camera 2.2 Safty instructions Please install the PC camera away from childrens hands. Please tie up the connecting cable of PC and PC camera short to prevent anyone being entangled by the cable. Please disconnect the PC camera in case of long term disuse of camera. Please not turn iris too much since it can damage lens or takes the lens out of the body. Please use soft cloth when you clean up the camera. Please dont disassemble the camera. Please contact with MTP for A/S or for any further information. 6 3. CD Installation instructions 3.1 CD S/W installation You should install the software of CD before you connect WebCAMeye Light to your computer. 1. The bottom menu will appear automatically when you insert the CD. ( In case that it does not appear automatically, you should operate Setup.exe on CD.) 2. The install program will be executed when you click Software Install button. (You may also execute the program operating Setup.exe inside of software folder of CD.) In case that you have used other PC camera, you should get rid of its driver before you install WebCAMeye Light PC camera driver. 7 3. Please click the Next button. 4. Please accept the use contract and click the Next button. 5. Please set up installation folder and click the Next button. 8 6. Please click the Install button. 7. Please click the Finish button when the installation is completed and appear the bottom page. 8. Then the first page will be appeared as bottom. 9 9. Please click the Driver Install button. 10. Please click the Next button. 11. Please click the Continue Anyway button when the buttom page appear while installation. (it will not always appear depending on the OS.) Above Windows logo test warning normally appear when they didnt request certifying to Microsoft but it has no relation to using our product. 10 12. The bottom page will appear when the installation is fully completed. Please click the Finish to reboot. 13. You will find that the program is installed on Start Menu and on Desktop after rebooting. (WebCAMeye and 301P USB Camera will be added on Start Menu) All the introduction pages has been standardized to Window XP but it is compatible for other OS following same procedure. 11 3.2 Driver recognition on Windows 2000/XP 1. Connect the WebCAMeye Light to spare USB port of PC. The bottom page will appear on the recognition procedure. 2. Please install and click Next button. 3. In case that the bottom page can appear while installing, please click Continue Anyway button. Above Windows logo test warning normally appear when they didnt request certifying to Microsoft but it has no relation to using our product. 12 4. It will install continuously. 5. The bottom page will appear after the installation is completed. 6. Please click the Finish button. 7. When the above page is appear, please click Yes and reboot. 13 8. Please check if the PC camera is recognized on Imaging Devices of Device Manager. Introduction pages are all of Window XP but it will be installed in the same procedure on Window 2000 Method of open Device Manager for Windows XP:
Start Menu Control Panel Switch to Classic View System Hardware Device Manager Method of open Device Manager for Windows 2000:
Start Menu Settings Control Panel System Hardware Device Manager 14 3.3 Driver recognition on Windows 98/98SE/ME 1. Connect the WebCAMeye Light to spare USB port of PC. Recognition procedure will be completed automatically. 2. Please check if the PC camera is recognized on Imaging Device of Device Manager. Introduction pages are all of Window ME but it will be installed in the same procedure on Window 98/98SE Method of open Device Manager for Windows 98/98SE/ME:
Start Menu Settings Control Panel System Device Manage 15 3.4 Remove software and Driver. 1. If you want to remove the software, select Uninstall WebCAMeye Light Software of WebCAMeye on Start Menu and click Yes button. 2. If you want to remove the driver, select Uninstall of 301P USB Camera on the Starting Menu and click YES button. 16 4. WebCAMeye Light usage 4.1 Name Camera lens Iris Flexible wire
(Free direction) Magnetic stand
(Main body has magnetic built-in.) 17 4.2 Focus adjustment. The image should be focused adjusting the Iris by hand for WebCAMeye Light. So the image can be out of focus because of the PC camera location. In that case, please adjust the focus as following instructions;
A . Turn the iris to the right: Focusing the image of long distance. B . Turn the iris to the left: Focusing the image of short distance. Focusing short distance Focusing long distance You should be careful not to turn the iris too much, which can cause the extracting the lens from the body. In case that the lens is taken out, dirt can enter between sensor and Lens so you should insert lens turning it to the opposite direction. 18 4.3 Adhesion of the magnetic panel. WebCAMeye Light has magnetic panel built-in on its bottom. So you are supposed to place the WebCAMeye Light on normal computer metal case or place it on the enclosed magnetic panel that is placed at the desired spot. The followings are some examples of adhering the magnetic panel;
A. Place it on the metal case of computer. B. Place it on the monitor C. Place it on the lap top 19 4.4 Set up the options WebCAMeye Light setup page is as bottom;
(Example : Camera Setup menu of WebCAMeye S/W setup button.) Adjust Brightness. Adjust Contrast. Adjust Gamma. Adjust Hue. Adjust Saturation. Adjust Sharpness. Adjust Red color grade. Adjust Green color grade. Adjust Blue color grade. Adjust Exposure. Brightness
( 1 ~ 40 Default : 20) Contrast
( 1 ~ 40 Default : 20) Default : 4)
( 1 ~ 5 Gamma
( 1 ~ 36 Default : 18) Hue
( 1 ~ 100 Default : 50) Saturation
( 1 ~ 5 Sharpness
(Manual/Auto Default : Auto) Red
(Manual/Auto Default : Auto) Green
(Manual/Auto Default : Auto) Blue
(Manual/Auto Default : Auto) Exposure USB Bandwidth Adjust USB Bandwidth.
(Manual/Auto Default : Auto) Vertical Flip Display vertical symmetry video (Check/Uncheck : Unchecked) Color Enable Mirror Flip Backlight Comp Make the video brighten at darkness Display color video. Display horizontal symmetry Video(Check/Uncheck : Unchecked)
(Check/Uncheck : Checked) Default : 3)
(Check/Uncheck : Unchecked) Dont remove AC frequency of the electric light Remove the 50Hz Ac frequency of Europe or Japan. Remove the 60Hz AC frequency of Korea or USA. Restore the factory value. Save the users setting value. Restore the users setting value. Flicker Off Flicker 50Hz Flicker 60Hz Reset Save Restore If the back light Comp is selected, the image printing speed will be reduced. 20 5. WebCAMeye Light S/W Usage 5.1 WebCAMeye Usage instruction This software is developed mainly for PC camera and is valid for showing the present image taken by PC camera, saving function of the photos and the video image as well as sending the photos by e-mail and connecting the EyeImage and Eyechat. A. Viewer function. Show the present image on the screen and adjust the resolution and set up the camera. WebCAMeye 21 Adjust the resolution. There are two ways to adjust the resolution. One is to press the right button of mouse placed on the screen and the other is to adjust it in the program setup dialog of set up button. Adjust screen size freely. Except the resolution adjustment, window size is supposed to be adjusted by pulling the corner of screen to ideal size. Size adjustment corner. 22 Full screen display. You can display the image data to through the full screen. It is useful to enlarge images or for surveillance monitor. The full screen image will be quite unnatural at low resolution. The image speed can be slow down since the full screen image requires higher system capacity. 23 Camera setup and Program environment setup. If you press Setup button, there are two menus; Camera setup and Program Setup. Camera setup Program setup Please refer to the index 4.4 set up the options to set up the camera. You can setup the saving folder, setup the image format and setup the resolution. 24 B. Photographing function. If you press Photo button on WebCAMeye, small sub-window will appear as follows. Photo: You can save the photo to BMP or JPG file.
(It is possible to select at the program set up box.) Edit: Connect the selected photo to the imaging program.
(BMP file will be operated by EyeImage and JPG file follows the ordinary windows image program.) Delete: Send the selected photo to the recycle bin. Mail: Attach the selected photo to the e-mail. You must setup mail program to send it by e- mail. 25 C. AVI file function. If you press AVI button on WebCAMeye, small sub-window will be appear. Record: Save the video by AVI file.
(If you want to stop the recording, press Save button.) Play: Play the selected AVI file. Delete: Send the selected AVI file to the recycle bin. 26 D. Connecting related programs Chat You can chat person-to-person operating the EyeChat program without opening the start menu. Connect to EyeImage program You should click Edit button after you select thumb nail on photo sub-window or you should do double clicks the selected thumb nail. EyeImage does not support JPG file. Please be noted that the ordinary window image program will be operated when you press Edit button after select JPG file or do the double click on JPG file. (ex : MS Paint) You can find all the necessary information of usage of all the programs in WebCAMeye software. Please refer to the information when you use the programs. 27 5.2 EyeImage Usage instruction EyeImage is an image processing base tool. Its function is similar to filter function of the Photoshop. It provides various functions like reversing images, adjusting image size and distorting colors. A. Applied functions. RGB, HSI, YIQ, CMYK and etc. Conversion Wavelet Transform (Walsh, Haar 2, Daubechies 4) Fast DCT (Zonal Coding) Arithmetic Operation(+,-,/,*,Darkest,Lightest,Average,Difference,OR) Geometric Operation (Translation, Rotation, Scaling, Mirror, Flip) Morphological Operation (Erosion, Dilation, Opening, Closing) Analysis (Sum, MSE, RMSE, PSNR, Std Dev., Min/Max, SSD, SAD, MAD, ) Blur, Sharpen, Emboss, Edge Detect Filter Variable Histogram (Equalize, Stretch, Color) Image Information (File name, size, using color, Bitmap header info.) 3 image format (BMP, RAW, PGM) EyeImage does not support JPG file. 28 5.3 EyeChat Usage instruction Eyechat program that is developed for P2P video chatting is a chatting program for chatters to communicate watching each other using PC camera. It is regarded as total chatting software providing Text and file exchanges and vocal conversation at the same time. A. Remote connection They can connect each other pressing connect button If they know IP address of each other. It will be easier to connect each other if they save their IP address at the connecting dialog to connect. The below window is the connected EyeChat screen. EyeChat 29 Add new name on the list If you press Connect button on EyeChat, the below page will appear. a. Please enter conversation partner at Connect information.
: Partners name Name IP address : Computer network parters IP address Port No. : Port Number of the partner b. Partners data will be registered to the Connect List when you press Add button. Amend the Connect List. a. Please click the name of Connect list. b. Then revise necessary part of the connect information c. It will be revised when you press Amend button Delete partner of the Connecting List a. Please select a name of connect list to delete. b. Then the name will be removed when you press Delete button. Delete all a. Please press Delete all to delete all. Connecting. It will be connected when you press Connect button after selecting the desired name of the Connect list. However it will be connected only when the desired person is also operating EyeChat. Port number is always 7070. Please dont use 7070 port at other software. 30 B. Data Sending Video and audio Sending Video and audio check boxes should be checked to send your picture and vocal data. Likewise your conversation partners ones also should be checked for you to receive his picture and voice. Text Sending You should write text on the text control and press Enter then your text with your ID will appear on the conversation control of your partner. Likewise the text of your partner will appear on your conversation control. 31 File Sending If you press File Send button, the below window will appear to select the file to send. When you select the file, the below window will appear on your partners side. The partner should press Yes button to receive the file It is possible to enjoy video chatting while sending files. Please refrain from sending files over 60M. 32 FAQ Q What can I do if I dont have Window CD even though it requires to insert window CD. A Window CD is necessary. You should prepare installed window CD like Windows 98, Windows 98SE or Windows ME to complete the installation properly. Q The Hardware certificate warning dialog appears at installing on Window 2000 and Window XP A When you install it on Window 2000 or on XP the warning message windows logo test can appear. It is recommended to ignore it and continue to complete the installation. In case that you dont want to see this message, please follow as the below screen. Q Can not see the screen at video chatting site. A Please check the setup conditions of Camera and resolution menu. You should check the camera wheather it recognizes image without problem and adjust the resolution properly. Automatic connection will be failed if there is any error caused at the automatic installation. In this case, you are required to do download and install the chatting program of the site manually. 33 Q The screen is invisible. A First of all, you should check if the PC camera is properly connected to PC through USB port. If everything is ok, please refer to the below mentioned procedure;
Windows98/98SE/ME Start Settings Control Panel System Device Manger Windows2000 Start Settings Control Panel System Hardware Device Manager WindowsXP Start Control Panel Switch to Classic View System Hardware Device Manager 1. In case that driver is installed at the imaging device. a. You should open the imaging device to check if the camera name is properly displayed. b. Please check if there is yellow exclamation mark. c. If there is yellow exclamation mark, please remove the driver and reinstall it. 2. In case that driver is not installed at the imaging device and other unknown device is installed a. Please remove the unknown device or others. b. Then remove the driver and reinstall it. 3. In case that imaging device is not displayed. a. Please Check if Universal Serial Controller is at Device Manager. b. In case that it is not installed. You should turn on USB device at BIOS. c. In case that it is installed, Please try to use another port. If it still doesnt work even though you try above mentioned instructions, PC camera may be out of order. Please contact with the distributor or head office of MTP In case that you have used other PC camera, you should get rid of its driver before you install WebCAMeye Light PC camera driver. A/S Company : Mobitechplus Inc. Address : #203, 32-5, Songwol-Dong, Jongno-
Gu, Seoul, Korea Tel. : 82-2-7303722 Fax. : 82-2-730-3726 34