USER MANUAL M710 Preface Thank you for buying this MID. Please read and retain all the operating instructions before operating the unit. I. Note 1. Avoid the unit being dropped. Avoid the display been shake seriously, or the display will be damaged or unusual. 2. Do not use metal object to touch the device to prevent it from short circuit. 3. Please backup your data in case your important data is lost, especially before you upgrade the firmware. 4. Do not disassemble. Do not wipe the surface of the unit by alcohol, thinner or benzene. 5. Do not disconnect the unit while it is formatting or uploading/downloading, or the procedures may lead to errors. 6. Avoid water or foreign objects enter the unit. 7. Do not use the unit in places that are extremely hot, cold, dusty, 8. Specifications are subject to change and improvement without or humid. notice. II. Introduction of cover Power on/off Earphone Jack 1. 2. 3. Micro USB interface 4. DC charger interface Volume+, Volume 5. TF-CARD interface 6. 7. Reset 1 Back Camera Loudspeaker Front Camera 8. 9. 10. III. Operation Instruction 1. Basic Operation 1.1. Power on/Power off Power on Press and hold the power switch for 5 seconds; the unit displays the start-up logo and enters the working mode. Power off Press and hold the power switch for 5 seconds to turn the unit off. Sleep While the device is at working status, press the power switch, it enters the sleeping mode, and the screen will be off then. Press the power switch again, it shift to the normal mode. You may use this function when you dont use the device temporary to save power. 1.2. Charging When the device prompts low battery, please charge it by provided charger. Note: To improve the longevity of the battery, you may charge for another 15 minutes after it prompts the battery is full. 1.3. Main menu Click the icon in the main interface, the main menu is appeared. It including the system setting, music playback, video playback, web browser and other applications you installed in the main menu. 2 2. Settings Click Settings in the main interface to enter the setting interface. Click the corresponding setting items to operate. 2.1Date and Time Setting Click Date & time in the setting interface to set the date and time. You may set the date, time zone, time, time format and date format etc. in the menu. 2.2. Brightness Select Display in the setting interface. Click Brightness to enter, and slide the bar to adjust the brightness. 2.3. Screen Timeout Adjust the delay before the screen automatically turns off. Select Display in the setting interface. Click Sleep to enter, and click the time you want. Note: The setting of screen timeout is unavailable while playing video. 3. Wi-Fi connection Click Settings in the main interface.Click Wi-Fi to turn on the WIFI, it lists the open network it searched. Click the name of the network; it pops up the setting window. You may connect it to WIFI according to the prompts. You need to input the user name and password if networks are encrypted. 3.1 Ethernet configuration The Unit support USB-Net-Card 4. Install, Uninstall and Run applications 4.1 Install There are many ways to install applications under Android. We introduce installation by Market here. Select the APK file you want and enter the application installation interface. Click Install to install the application automatically. After installation, it prompts Open and Finish. Click Open to open the application. Click Finish to exit. 3 4.2 Uninstall You may use the corresponding third party software management tool or the installed application management software of the device to install applications. Select Setting/Apps to select the installed applications and check the attribute of it or uninstall it. 5. Connect to internet 5.1. After connecting with WIFI, open the browser and input the web address, you can browse the web then. icon to enter the bookmark to view the browse 5.2. Click the history. Click the web page you want to open it. 6. Audio and video playback 6.1. Audio playback Click the MUSIC in the main menu to enter the audio playback interface. It lists the audio files in the device, and you may click the file name to play it. in the audio playing interface, click the icons to play/pause/ increase volume/ decrease volume/ FF/ REW. 6.2. Video Playback Click the Gallery in the main menu to enter the video playback interface. It lists the video files in the device, and you may click the file name to play it. in the video playing interface, touch the screen to pop-up the operation icons and click the icons to play/pause/ increase volume/ decrease volume/ skip to next file/skip to previous file. 7. Picture viewing Click Gallery in the main menu to enter the picture folder list. Select and click the folder you want to enter, it displays the . click the thumbnail of the picture to view it. Touch the screen to pop-up the operation icons while viewing the picture, you may zoom in/zoom out/ skip to next picture/skip to previous picture/ rotate/ delete the picture 4 8. Camera Click Camera in the main interface. 8.1 Camera If the cursor is at position, the device is at Camera mode. Click Click colour effect. to take picture. to set the scene mode, Picture size, Picture quality, and to set white balance. Click 8.2 DV If the cursor is at position, the device is at DV mode. to take picture. to set the colour effect or restore to default settings. Click Click 9. Connect with external device 9.1. Connect with PC Connect the device with the PC via the USB cable. The PC appears two new disk symbols after connected successfully. One is the TF card, and the other is the built-in flash. 9.2. Applications For convenient usage, we installed some third party software in the MID. For detailed operation methods, please check the corresponding instruction. Some of the software may be able to be used in some area because of network service. IV. Troubleshooting 1. What if the device is abnormal during operation?
Answer: 1) Reboot the device to see if it works OK. 2) Charge the device by the charger to activate the battery. Make sure it has power before you operate it. 3) It is suggested to upgrade the OS of the device by professional. 5 2. Why the standby time is so short sometimes?
Answer: the use time of the battery is all depend on the temperature and use instance. If the temperature is too high or too low, the use time of the battery might be effected. It is suggest using the device in normal temperature. The using time is also affected by increased volume and frequently operation. VI. Specifications Item Display Touch panel OS Input method Capacity External Capacity Audio Video E-book Wireless network Language OTG Temperature Battery M710 800X480/1024*600 Capacitive touch screen Android 4.2/4.4 Soft keypad 4GB -16GB(Take the object as the standard) TF-CARD, up to 32GB MP3,WMA,FLAC,APP,OGG.(support all audio formats) MPEG4-sp,asp,divx,WMV,RMVB,H.264/1080P
(support all video formats) Support Support WIFI Multi-language Support
-20C to 60C poly-lithium battery MEANING OF THE DUSTBIN SYMBOL Protect our environment: do not dispose of electrical equipment in your domestic waste. Please return any electrical equipment that you will no longer use to the collection points provided for their disposal. These simple steps can help to avoid the potential effects that incorrect waste disposal can cause on the environment and human health. This will contribute to recycling and other forms of re-use of electrical and electronic equipment. Information concerning where the equipment can be disposed of can be obtained from your local authorities. 6 FCC Warning Statement Your device is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. The SAR for this device is compliant with these SAR exposure requirements. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of (http://transition.fcc.gov/oet/ea/fccid/) after searching on FCC ID 2AC56-MBY700. Additional information on Specific Absorption Rates (SAR) can be found on the FCC website at (http://www.fcc.gov/encyclopedia/radio-frequency-safety). This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The Grantee is not responsible for any changes or modifications not expressly approved by for compliance. Such the party responsible 7 modifications could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. 8