UHF UHF Wireless Microphone System Receiver 5 123 10 Transmitter 5 124 10 Product description Install hotshoe camera mount Product connection diagram 6 7 11 8 12 13 6 7 11 9 12 a b a b 8. a: RF status light b: Audio light 9. a: Input peak indicator b: Audio input indicator 10. Switch lock 11. Battery bin 12. Belt clip 13. Hotshoe camera mount 1. antenna 2. Low battery indicator 3. 3.5mm audio output interface 4. 3.5mm microphone input interface 5. Channel selection 6. Volume adjustment 7. Channel display LED light Battery Installation LED indicator status Status Receiver Transmitter a: Red receiving status indication Audio input peak indication b: Green audio output indication Audio input normal level indication No light No receive or no audio signal No audio signal input Packing List Receiver Transmitter Mobile phone audio cable Camera audio cable Lavalier microphone Belt clip Hotshoe camera mount Instruction manual Smartphone connection Microphone connection Effective Working Distance (ideal environment) : 50M Input Gain Adjustment Range : 5 level adjustment setting, every 3dB step Receiver and Transmitter indicators is as follows Receiver The red indicator light does not illuminate when there is no signal, and the red indicator light is on when the signal is received. Product Specification Transmitter Specifications Oscillation : PLL synthesized Transmission Power : 10 dBm Carrier Error : 0.005%
Harmonic radiation : -32 dBm Modulation : FM RF Carrier Frequency Range : 470 ~ 960MHz
(Depending on country or region) Frequency Stability : 0.005%
Nomina/Maximum Frequency Offset : 65 KHz Max Input Level : 420 mV1%
Input Lmpedance : 2.2 K Frequency Setting : Manual key setting Power : AA 1.5V x 2 Normal Working Current : Battery powered : 120mA Battery Life : 11Hours Dimension : 96 x 60 x 18.8 (mm) Net Weight : 55g (without battery) 1 2 1 Push the bottom of the belt clip ( ) to create a certain space between the belt clip and the receiver. Align the belt clip with the two vertical grooves on the hotshoe camera mount and insert the camera mount ( ) in the direction of the arrow. Push in the hotshoe camera mount until the belt clip fits into the horizontal groove on the handle of the camera mount. 2 Disassemble hotshoe camera mount 1 2 3 Push and hold the position marked PUSH on the hotshoe camera mount ( ), separate the horizontal part of the belt clip from the level and groove on the hotshoe camera mount ( ), and then push the hotshoe camera mount in the direction of the arrow ( ). 3 2 1 3.5mm 4-pole jack 3.5mm 3-pole jack Camera connection 3.5mm 3-pole jack 3.5mm 3-pole jack Audio output connection
* Please connect the cable to the same terminal as the above picture according to the device you are using. Matching of transmitter and receiver If the radio signals of the receiver and transmitter are connected properly, the red light indicator of the receiver will be long on, The number of channels displayed by the digital light is the same as that of the transmitter; if not connected, the red indicator of thereceiver will not be on. Before leaving the factory, the transmitter and receiver of each product have been set up in pairs, and can be used directly when starting. How to set the channel of the Receiver and Transmitter 1. Turn on the Receiver/Transmitter. 2. Long press the Channel button and the letters of the digital light will be converted sequence. 3. Set Receiver and Transmitter to the same channel the red light on Receiver turns on. Audio Compression : Digital Audio Compression Audio Frequency Response : 150 Hz ~ 1800 Hz 3 dB Dynamic Range : 90 dB (Circuit) S/N : 81 dB (Circuit) T.H.D : 0.8%, @1KHz Working Temperature Range : -10C ~ +50C Receiver Specifications Receiving Mode : Superheterdyne Mirror Suppression : 45 dBm Noise Regulation : built - in setting parameters RF Sensitivity : when input is 10 dBu, S/N 45 dB Frequency Synchronization : Manual key settings Max Output Level : LINE : 0.72 Vpp Output Level Adjustment Range : 5 level for adjustment, attenuation adjustment, Every 3dB step Output Impedance : 400 Power : AA 1.5V x 2 Normal Working Current : 3V 100mA Battery Life : 11Hours Dimension : 96 x 60 x 18.8 (mm) Net Weight : 55g (without battery) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF Exposure Information The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Quick User Guide
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -