FCC ID: 2AJ5SEM00556 2.4GHz Module Small E01C

LEGAL STATEMENT FCC STATEMENT:

This device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) this device may not causeharmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Please notice that if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains FCC ID:

meaning may be used. any similar wording that expresses the same This device contains license exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada s license exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. L' metteur/r cepteur exempt de licencecontenu dans le pr sent appareilestconforme aux CNR d'Innovation, Sciences et D veloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitationestautoris e aux deux conditions suivantes :

1)L'appareil ne doit pas produire de brouillage;

2)L'appareil doit accepter tout brouillage radio lectriquesubi, m me si le brouillageest susceptible d'encompromettre le fonctionnement. Please notice that if the I outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains IC:

meaning may be used. identification number is not visible when the module is installed inside another device, then the any similar wording that expresses the same Notez que si le numrod'identification I unetiquetteindiquant le module attach doit galementtreaffiche l'extrieur de l'appareilo le module estinstall. L'tiquetteextrieurepeuttrelibellecomme suit: contient IC:

mmesens. n'est pas visible lorsque le module estinstall dans un autreappareil, toute expression similaire qui exprime le The device must be professionally installed The intended use is generally not for the general public.It is generally for industry/

commercial use.The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. the user has no access to the connector. Installation must be controlled. Installation requires special training This module has been assessed against the following FCC rule parts: CFR 47 FCC Part 15 C (15.247, DTS). It is applicable to the modular transmitter This radio transmitter FCC ID:2AJ5SEM00556 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. The concrete contents to check are the following three points. Must use antenna such as with gain not exceeding dBi;

Should be installed so that the end user cannot modify the antenna;

Feed line should be designed in 50ohm Fine tuning of return loss etc. can be performed using a matching network. L'metteur radio FCC ID:2AJ5SEM00556 a tapprouv par la FCC Utilisez les types d'antennesnumrs ci dessous et indiquez le gain maximal admissible. Le gain du type d'antenne non inclus dans cettelisteestsuprieur au gain maximal de l'un des types numrs et ne doit pas treutilis avec cetquipement. Le contenuspcifique de l'inspectioncomprend les trois points suivants. Une antennedont le gain ne d passe pas utilis e;

dbi, telle que

, doit tre Doit tre install l o l'utilisateur final ne peut pas modifier l'antenne;

La ligned'alimentation doit treconue pour 50 ohms Le rseaucorrespondantpeuttreutilis pour affiner la perte de retour, etc. Antennas:

Must use the device only in host devices that meet the FCC/ISED RF exposure category of be co located or operating in conjunction with any other antenna or transmitter. This transmitter must not The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements related to the transmitter as show in this manual(FCC/IC Canada statement). Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID:2AJ5SEM00556 IC: 22061 EM00556 The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturers instruction manual. This module is stand alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. Any company of the host device which install this modular should perform the test of radiated &

condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 &

15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally. This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: 2AJ5SEM00556 and Contains IC: 22061 EM00556 l'hte doit utiliserl'instrumentuniquement dans des dispositifs qui r pondent manuel de l'utilisateur final doit inclure la fcc / (cat goried'exposition rf

. le la partie 15 / (fac rss gen d clarations de conformit relatives l' metteur que de montrer dans cemanuel. le fabricant estresponsable de la conformit de l'hte, le syst me d'accueil avec le module install avec toutes les autres exigences applicables du syst me comme la partie 15 b, ices 003. accueillir le fabricant estfortementrecommand de confirmer la conformit avec les exigences de la fcc / ( metteurlorsque le module est install dans l'hte. le dispositifd'accueildoiventavoirune tiquetteindiquantcontient FCC ID:2AJ5SEM00556 IC: 22061 EM00556

MOTION S.P.A. Date:1/20/2022 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 To whom it may concern:

I, the undersigned, hereby authorize UL Verification Services Inc. to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by UL Verification Services Inc. on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing UL Verification Services Inc. as our representative, we still recognize that we are responsible to:

a) comply with the relevant provisions of the certification program;

b) c) d) e) f) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

g) h) i) j) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to us relating to the products compliance with requirements of the relevant standard and to make these records available to the when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signed by:

Company Name: MOTION S.P.A. Contact Name: Elio Ravaioli Title of PersonCEO Address:Via Navicella 26, 47122 Forli' (FC), Italy

2AJ5SEM00556 Request for Confidentiality MOTION S.P.A. Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

FCC ID:

To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards Company Name: MOTION S.P.A. Contact Name: Elio Ravaioli Title of PersonCEO Address: Via Navicella 26, 47122 Forli' (FC), Italy Date:1/20/2022

MOTION S.P.A. DATE : 2022-01-20 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Request for Short-Term Confidentiality Company name:

FCC ID: 2AJ5SEM00556 FCC Part 15 Certification Pursuant to Sections 0.457 and 0.459 of the commission rules, and in accordance with the FCC Public notice dated June 15, 2004 (DA 04-1705), we hereby request short-term confidentiality for the following items prior to marketing the device.:

(1) Test Setup Photos

(2) External Photos

(3) Internal Photos

(4) User Manual The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Sincerely, Signature Company Name: MOTION S.P.A. Contact Name: Elio Ravaioli Title of PersonCEO Address: Via Navicella 26, 47122 Forli' (FC), Italy