EN Instruction Manual mo.hub V1.0 Thank you very much for purchasing a high quality motogadget product - Made in Germany. Please read the following information and recommendations thoroughly and follow these in-
structions during installation and use of the instrument. No liability shall be assumed by mo-
togadget for damage or defects resulting from negligence or failure to follow the operating and contact:
motogadget GmbH Koepenicker Str. 145 D - 10997 Berlin Tel. +49 (0)30-6900410-0 www.motogadget.de info@motogadget.de Copyright 2009-2020 by motogadget GmbH, Berlin motogadget and mo.hub are registered trademarks of motogadget GmbH, Berlin, Germany. 1 Review of Delivery All products from motogadget are thoroughly checked to ensure they are completely fault-free when dispatched. Please check the received goods immediately for possible transport dam-
age. If you nd any damage or other de ciencies, please contact us immediately. In this regard, we refer to our General Terms of Business and Delivery, which are published at www.motogadget.com. Should a return of the received delivery be agreed, please note that we only take back goods in their original packaging. The mo.unit and its accessories must be returned within the legal period of time and without any traces of use. We shall not assume any liability for returns which are insuf ciently insured or packed. 2 Exclusion of Liability THE DEVICE AND ITS ACCESSORIES MUST BE INSTALLED BY A CERTIFIED MOTOR-
CYCLE TECHNICAN AND IN AN AUTHORIZED SERVICE CENTER. REVERSE POLARITY OR VOLTAGE ABOVE 25V MAY RESULT IN DAMAGE TO THE MO.HUB. THE DEVICE THEN HAS TO BE REPLACED AND ALL CLAIMS OF WARRANTY ARE DELETED. MOTOGADGET ACCEPTS NO LIABILITY FOR DIRECT OR INDIRECT DAMAGE OR SUBSEQUENT DAMAGE OF ANY KIND RESULTING FROM THE USE, INSTALLA-
TION OR CONNECTION OF THE DEVICE OR OTHER DELIVERED EQUIPMENT. THIS EXCLUSION OF LIABILITY PARTICULARLY INCLUDES DAMAGE TO PERSONS, MATERIAL LOSSES AND FINANCIAL DAMAGES. THE USE IN AREAS OF PUBLIC TRAF-
FIC ENSUES AT THE USERS OWN RISK. DEVICE HOUSINGS AND ALL OTHER DELIVERED PARTS MUST NOT BE OPENED OR DISMANTLED. IN CASE OF NON-COMPLIANCE, ALL WARRANTY CLAIMS BECOMES INVALID. THE USE OF THE DELIVERED DEVICE AND ITS ACCESSO-
RIES FOR RACING OR OTHER COMPETITIONS AS WELL AS FOR ANY USE NOT CORRESPONDING TO THE RECOMMENDED APPLICATION ALL WARRANTY CLAIMS SHALL BE INVALID. 3 Safety Instructions THE VEHICLE BATTERY MUST BE COMPLETELY DISCONNECTED PRIOR TO ANY WORK ON THE VEHICLES ELECTRICAL SYSTEM. FIRST, DISCONNECT THE NEGA-
TIVE TERMINAL AND THEN THE POSITIVE TERMINAL. FOR RECONNECTION PROCEED IN THE REVERSE ORDER. USING THE MO.HUB WITH PLUS POLE CONNECTED TO VEHICLE FRAME (OLDER ENGLISH MOTORCYCLES) IS NOT POSSIBLE. INSTALLATION AND ELECTRICAL CONNECTION OF THE MO.HUB MAY ONLY BE CARRIED OUT BY A CERTIFIED MOTORCYCLE TECHNICIAN. ALL CABLE DIAMETERS MUST BE DIMENSIONED ACCORDING TO THE CURRENT FLOW (REFER TO CHAPTER 8.5). 4 Application The mo.hub is a universal data interface between vehicle and motogadget instrument or smartphone. Compatible vehicles with BUS or OBD interface are connected to the mo.hub by a supplied vehicle-mounted plug (Plug & Ride). For vehicles without interfaces, the required signals (tachometer, speed, control lights, etc.) must be tapped individually and connected to the mo.hub. The con guration of the mo.hubs is done by our app m.ride. For this, the vehicle and the connected instrument are selected. In addition, m.ride offers comprehensive vehicle management with a logbook and a linked vehicle database. We are continually expanding the list of mo.hub compatible vehicles. 5 Overview area of Bluetooth Antenna-
do not cover with metal serial no.
(important for support requests) angeben) terminal marking Status LED mouning holes for cable cover plug-in / relase connecting cabel by phusing orange inserts with a screw driver blade 6 Mounting the cable cover & cable guide M3x16 countersunk cable ties 7 Mounting options cable ties M4 screws 8. Connecting motogadget instruments to the mo.hub 8.1 motoscope mini and combi-frame or handle bar clamp mo.hub motoscope mini combi-frame Lenkerklemme Port Nr. 3 H S T U V W X Y Z Kabelfarbe schwarz rot gelb wei grn Kabelfarbe orange | gelb | violett wei Kabelfarbe orange | blau rot schwarz braun rot blau grn gelb grn violett schwarz wei 8.2 motoscope tiny und motoscope classic mo.hub Port Nr. 1 2 3 H S T U V W X Y motoscope tiny motoscope classic Kabelfarbe rot schwarz braun lila orange grn wei gelb blau Kabelfarbe schwarz | wei-grn rot gelb wei grn grau wei-orange blau wei-gelb 9 Connecting the vehicle to the mo.hub 9.1 vehicles without data BUS mo.hub Port Nr. 1 2 3 6 7 8 9 10 11 12 A B C D E S T Fahrzeug Batterie +12V (ber 1A Kabelsicherung) Zndungsplus Fahrzeugmasse (GND) Mentaster (GND) Fernlicht (+12V) Error / MIL (GND) Blinker L (+12V) Blinker R (+12V) Neutral (GND) ABS (+12V) ltemperatur Sensor (motogadget Artikel 9001005 / 9001007 / 9001002) ldruckschalter (GND) Lufttemperatur Sensor (motogadget Artikel 1005090) Wassertemperatur Sensor (motogadget Artikel 9001005 / 9001007 / 9001002) Fahrzeug-Tanksensor (0-500 Ohm - GND) Drehzahlsignal (Primrkreis Zndspule) Tachosignal (alle Typen) 9.2 BMW modells with LIN Bus 9.2.1 Fahrzeugtyp Identi zierung BMW models from 2015 with a 6 pin instrument plug with dimensions of approx. 9x10x22mm, are equipped with a LIN bus for communication between control unit and instrument. 9.2.2 Connecting the vehicle-speci c plug and the battery cable to the mo.hub mo.hub Port Nr. 1 3 4 motogadget BMW LIN Fahrzeugstecker motogadget Batterieanschlusskabel (4005102) von Batterie Plus motogadget Stecker (4005100) Kabel schwarz motogadget Stecker (4005100) Kabel rot 9.2.3 Installation 1) Jack up vehicle, remove seat and tank, disconnect battery ( rst minus, then plus) 2) Unscrew OEM instrument, unplug connector, unscrew OEM instrument carrier. 3) attach the motogadget instrument to the vehicle-speci c motogadget retaining plate and connect the tail cable of the motogadget instrument to mo.hub 4) Connect motogadget vehicle-speci c plug and battery cable to mo.hub 5) Screw the motogadget retaining plate with instrument to the fork bridge with the OEM screws. 6) Attach mo.hub to the upper frame tube with cable ties, avoiding collision pay attention to mo.hub housing and tank. 7) motogadget battery connection cable, OEM instruments connector plug and motogadget Instuments Lay the cable free of kinking and abrasion to the mo.hub and cable with cable ties attach to the frame. Allow enough play for steering movements. 8) Insert the plug of the OEM speedometer (not tachometer!) In the with motogadget Insert vehicle plug. The second OEM instrument plug (if available) with Protect heat shrink tubing from splash water. 9) The eyelet of the motogadget battery connection cable with the battery-plus connection terminal connect 10) Connect the battery ( rst plus, then minus) 11) Install the tank and seat 9.3 BMW Modells with CAN Bus 9.3.1 Vehicletype identi cation BMW models from 2010 - 2014 a 6 pin instrument plug with the dimensions of approx. 14.5x23.5x40mm, are equipped with a CAN bus for communication between control unit and instrument. 9.3.2 Connection of the vehicle-speci c plug to the mo.hub mo.hub Port Nr. 1 2 3 F G motogadget BMW CAN Fahrzeugstecker
(4005101) rot braun schwarz blau lila 9.3.3 Installation 1) Jack up the vehicle, remove seat and tank 2) Unscrew OEM instrument, unplug connector, unscrew OEM instrument carrier. 3) attach the motogadget instrument to the vehicle-speci c motogadget retaining plate and connect the tail cable of the motogadget instrument to mo.hub 4) Connect motogadget vehicle-speci c plug and battery cable to mo.hub 5) Screw the motogadget retaining plate with instrument to the fork bridge with the OEM screws. 6) Attach mo.hub to the upper frame tube with cable ties, avoiding collision pay attention to mo.hub housing and tank. 7) OEM instrument connector and motogadget instrument cable kink and scuff-free Lay to the mo.hub and secure the cables to the frame with cable ties. Suf cient Allow game for steering movements. 8) Insert the plug of the OEM speedometer into the vehicle with motogadget plug. 9) Install the tank and seat 10 settings for motogadget instruments motoscope tiny and motoscope mini Circ = 2000 / ImpW=1 / ImpE=1 motoscope classic Circ=200 / ImpW=4 / ImpW=1 11 Return and Complaint Before sending your mo.hub to us for technical review, please contact Technical Support. Visit our website and follow the instructions under Support. For support requests, we always need the serial number (sticker top mo.hub, your smartphone model used, the app version (see main menu under About).) To return the item, please follow the instructions under Service on our website. CE marking The unit described in this document is in accordance with the of cial European directives. A copy of the declaration of conformity can be provided on request. This equipment complies with the essential requirements of EU Directive 1999/5/EC. The vehicle body control module integrated in this product has been pre-certi ed separately and is marked with CE0168 R&TTE directive. Hereby, motogadget declares that motogadget products and accessories are in compliance with the essential requirements and other relevant provisions of the EU Directive 1999/5/EC. WEEE directive The wheelie bin symbol on the product or its packaging indicates that this product shall not be treated as household waste. In line with EU Directive 2002/96/EC for waste electrical and electronic equipment (WEEE), this electrical product must not be disposed of as unsorted mu-
nicipal waste. Please dispose of this product by returning it to the point of sale or to your local municipal collection point for recycling. By doing this you will help conserve the environment. Regulations PRODUCT INFORMATION:
Manufacturer:
Model:
FCC ID:
IC:
motogadget GmbH mo.unit blue 2AIF8-4005000 21495-4005000 FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. INFORMATION TO USER:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the distance between the equipment and the receiver Connect the equipment to outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help. Canada Industry Canada (IC) This device complies with Industry Canada license-exempt RSS Standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). Son fonctionnement est soumis aux deux conditions suivantes:
(1) Cet appareil ne doit pas provoquer dinterfrences et (2) cet appareil doit accepter toute interference, y compris celles pouvant causer un mauvais fonctionnement de lappereil. Das motogadget Team wnscht Ihnen eine angenehme und sichere Fahrt sowie viel Spa mit Ihrem neuen mo.hub.