FCC ID: IHDH270 Bluetooth Wireless Headset

BEFORE YOU BEGIN Before using this product, read the Important Safety and Legal Information pamphlet and follow its instructions. Take a moment before you get started to familiarize yourself with your new H270 Headset. 1 CHARGE Your Headset's Battery 2 START BLUETOOTH FEATURE Your Phone Your phone's Bluetooth feature is off by default. To use your headset, you must turn on the Bluetooth feature in your phone. motorola H270 Quick Start Guide Volume Button Call Button Indicator Light Earhook Speaker 1 2 Microphone Power Switch START HERE >

Features and Functions IMPORTANT:

Be sure to first follow the steps on the top row of this guide to complete initial setup of your H270. Motorola, Inc. Consumer Advocacy Office 1307 East Algonquin Road Schaumburg, IL 60196 www.motorola.com 1-877-MOTOBLU 1-888-390-6456 (TTY/TDD United States for hearing impaired) Guide Number: 68000202001-A Bluetooth QD ID: Bxxxxxx MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. The use of wireless devices and their accessories may be prohibited or restricted in certain areas. Always obey the laws and regulations on the use of these products. The Bluetooth trademarks are owned by their proprietor and used by Motorola, Inc. under license. All other product or service names are the property of their respective owners. 2008 Motorola, Inc. All rights reserved. Verify slide switch is in the off position

(toward the charging port). Plug the Motorola charger into the end of the headset. The indicator light turns red or purple when the battery is charging. It may take up to 1 minute for the indicator light to turn on. When the headset's battery is fully charged

(about 2 hours), the indicator light turns blue. Disconnect the charger. 3 Note: Headset is not functional while charging. Note: This product uses a lithium ion, rechargeable, non-replaceable battery. Under normal use, the expected life of the rechargeable battery is approximately 400 charges. TURNING HEADSET ON AND OFF To turn your headset on, slide the switch toward the microphone. The indicator light flashes blue three times, then flashes in blue and purple (if connected with a device) or is steadily blue (if ready to be paired). To turn your headset off, slide the switch toward the charging plug. The indicator light flashes three times then turns off. Indicator Light Power Switch Be sure to position the ear cushion into your ear canal for optimal audio performance and comfort. 3 PAIR Your Headset and Phone 4 TEST AND USE USING YOUR H270 For most Motorola phones (at the main menu):

1 Press (Menu) > Settings > Connection >

Bluetooth Link > Setup. M Scroll to Power. Select Change. Scroll to On. 2 3 4 5 Before you can use your headset, you must pair

(link) it with your phone. Step A - ENSURE HEADSET IS IN PAIRING MODE Power on headset by sliding the Power switch towards the microphone to initiate easy pairing. After a few moments, the indicator light will be steadily lit in blue to indicate headset is in pairing mode. Indicator Light

(steadily blue for pairing) Press Select to turn on the Bluetooth feature. The Bluetooth feature remains on until you turn the feature off. Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide. If the headset does not enter pairing mode, see TROUBLESHOOTING for help. Power Switch WEARING THE HEADSET To wear your headset, flex the earhook and loop it over your ear as shown. CHANGING FOR USE ON OTHER EAR You can wear your H270 headset on your left or right ear. The headset comes ready for the right ear. To change the headset for the left ear:

1 2 3 Gently lift and pull the top of the earhook up and off speaker stem, as shown. Flip the headset over. Attach the earhook to the speaker stem, as shown. Step B - SET YOUR PHONE TO LOOK FOR YOUR HEADSET 1 2 3 4 5 For most Motorola phones:

On your Motorola phone, press (Menu) >

M Settings > Connection > Bluetooth Link >

Handsfree > Look for Devices. The phone lists Bluetooth devices it finds. Select Motorola H270. Select OK or Yes to pair your headset with your phone. Enter the passkey: 0000 Select OK. When your headset successfully pairs and connects with your phone, the indicator light changes from steadily lit to flashing blue and purple. Note: These steps are for most Motorola phones. For other phones, see your phone's user's guide. MAKING CALLS Function Receive a call Reject a call End a call Make a voice dial call Answer second incoming Use phone to answer

(follow your phones call instructions) Action Tap the Call button Press and hold a Volume button until the ringer stops Tap the Call button Tap the Call button and wait for voice prompt Note: Your H270 supports both Handsfree and Headset Profiles. Accessing call functions depends upon which profile your phone supports. See your phone's user's guide for more information. Note: Some features are phone/network dependent. 1 2 Your phone and headset are now paired and ready to make and receive calls. To make a call:

Place the headset over your ear. On the phone, dial the number you want to call and press SEND key on your phone. If your phone and headset are successfully paired, you will hear ringing on the headset. After you have successfully paired your phone and headset, you don't need to repeat these steps. For daily use, ensure that your headset is turned ON and that your phone's Bluetooth feature is ON. See Features and Functions on the bottom row for information on using your H270 Note: If desired, your headset can be restored to original factory settings. This action will erase all pairing information stored in your headset. Thus, you will need to pair your phone and headset again (see step 3). Note: To restore your headset to original factory settings, press and hold both Volume and Call buttons at the same time and slide Power switch to ON. INDICATOR LIGHT With the Charger Plugged In INDICATOR LIGHT With No Charger Plugged In Headset Indicator Red Purple Blue Headset Status Charging (battery level less than 70%

charge) Charging (battery level more than 70%

charge) Charging complete Note: Your battery is designed to last the life of the product. It should only be removed by a recycling facility. ANY ATTEMPT TO REMOVE OR REPLACE YOUR BATTERY WILL DAMAGE THE PRODUCT. Headset Status Headset Indicator Power off Off Powering on/off Three blue flashes Steady blue Pairing/connect mode Rapid blue/purple flashes Connection successful Incoming/outgoing call Quick blue flash Slow blue pulse Connected (on a call) Standby (not on a call) Slow blue flash Idle (not connected Slow red flash to phone) Attempting to connect Steady red Quick red flash Low battery Note: After 30 minutes on a call or of inactivity, the light stops flashing to conserve power, but the headset remains on. TROUBLESHOOTING My headset will not enter pairing mode. Make sure that any devices previously paired with the headset are turned off. If the indicator light is not steadily lit in blue, turn off both the other device and headset, wait 10 seconds, then turn headset back on. Wait for the indicator light to become steadily lit in blue, indicating the headset is now in pairing mode. My phone doesn't find my headset. Make sure the indicator light on your headset is on (lit in blue) and steady when your phone is searching for devices (see step 3). My headset worked before but now it's not working. Make sure your phone is on and the Bluetooth feature is turned on in your phone (see step 2). If the Bluetooth feature was turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2) and pair your phone and headset again (see step 3). Support. If you need more help, contact us at 1-877-MOTOBLU or visit us at www.motorola.com/Bluetoothsupport AUDIO TONES Audio Tone Ascending tone Two descending tones Ring tone Two short tones when pressing Volume button High/low tones repeated every 60 sec. No audio indications;

deteriorating quality Two ascending tones Headset Status Powering on Powering off Incoming call Volume at minimum or maximum Low battery Out of range Connected to phone European Union Directives Conformance Statement Hereby, Motorola declares that this product is in compliance with:

The essential requirements and other relevant provisions of Directive 1999/5/EC. All other relevant EU Directives. Product Approval Number The above gives an example of a typical Product Approval Number. You can view your products Declaration of Conformity

(DoC) to Directive 1999/5/EC (to R&TTE Directive) at www.motorola.com/rtte. To find your DoC, enter the product Approval Number from your products label in the Search bar on the web site. TROUBLESHOOTING My phone does not find my headphones. Make sure the L indicator light on your headphones is on and steady when your phone is searching for devices (see step 3). My headphones worked with my phone before but now their not working. Make sure your phone is on and the Bluetooth feature is turned on in your phone (see step 2). If the Bluetooth feature has been turned off or was turned on only temporarily, you may need to restart the Bluetooth feature (see step 2). If you have confirmed the Bluetooth feature is on in your phone, pair your phone and headphones again (see step 3). Support. If you need more help, contact us at 1-877-MOTOBLU or visit us at www.hellomoto.com/bluetooth and click Support. DRAFTDRAFT

Compliance Certification Services Inc. Internal Photo Report No.80822302 Page 3 of 4 Compliance Certification Services Inc. Report No.80822302 Page 4 of 4

Compliance Certification Services Inc. External Photo Report No.80822302 Page 1 of 4 Compliance Certification Services Inc. Report No.80822302 Page 2 of 4

Labe Drawing & Location Bluetooth Wireless Headset Model No: H270 FCC IDIHDH270

Statement of Compliance Letter FCC ID : IHDH270 Product : Bluetooth Wireless Headset Model : H270 To whom it may concern:

We, the undersigned, hereby certify that we responsible to comply with the relevant provisions of the Bluetooth 2.1+EDR specification and certificate program as bellows:

a. Comply with the Bluetooth 2.1+EDR technical description of the hopping sequence pseudorandom. b. Comply with the Bluetooth 2.1+EDR technical description of each channel used equally on average. c. Comply with the Bluetooth 2.1+EDR technical description ,the associated system receiver have a compliant input bandwidth, based on the measured 20 dB emission bandwidth. d. Comply with the Bluetooth 2.1+EDR technical description ,the associated system receiver have the ability to hop in synchronization with the transmitter. e. The design of the frequency hopping system allow it to comply with all pertinent requirements when presented with a lengthy data stream. f. The frequency hopping system comply with the non-coordination requirement.

600 N. U.S. Highway 45 Libertyville Illinois 60048-5343 United States Date: August 18, 2008 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 c.c. Compliance Certification Services Certification Division 47173 Benicia Street Fremont, CA 94538, USA To whom it may concern:

I, the undersigned, hereby authorize Taiwan office of Compliance Engineering Services, Inc., d.b.a. Compliance Certification Services and hereafter referred to as CCS TW, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by CCS TW on our behalf shall have the same effect as acts of our own. I, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). In authorizing CCS TW as our agent, we still recognize that we are responsible to:

a) b) c) d) comply with the relevant provisions of the certification program;

make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints;

make claims regarding certification only in respect of the scope for which certification has been granted;

do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized;

e) f) g) h) i) j) upon suspension or cancellation of certification, discontinue use of all advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division;

use certification only to indicate the products are certified as being in conformity with specified standards;

endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner;

ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division;

keep a record of all complaints made known to the us relating to the products compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested;

take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification;

k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Andrew Bachler FCC Liaison Motorola Inc. REMARK:

1. 2. 3. This authorization letter will be sent along with your application when filing with the Certification Division. Please follow the format and type it on company letterhead and send original to us. Authorized signature must be in agreement with grantee code contact in FCC database.

600 N. U.S. Highway 45 Libertyville Illinois 60048-5343 United States IHDH270 Request for Confidentiality Date: August 22, 2008 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject:

FCC ID:

To Whom It May Concern:

Pursuant to the provisions of Sections 0.457 and 0.459 of the Commissions rules (47 CFR 0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Theory of Operation Antenna specification Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commissions policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 2008/10/15. External Photos Internal Photos Test Setup Photos User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Andrew Bachler FCC Liaison Motorola Inc.