FCC ID: ABZ99FT5001 CDM1550LS+ MOBILE RADIO

Installation Installation Mounting Hardware Installation Roof Mount General The installation procedure which follows is for a typi-

cal passenger car. The procedure may vary slightly with the type of vehicle on which the antenna is to be installed. Generally speaking, however, the procedures outlined are of a universal nature. NOTE The antenna should be mounted on a flat metal roof of .020 to .040 inch thickness. 1. First, select a location for the antenna as near the center of the roof as possible. 2. The headlining may be probed with the fin-

gers to make sure that all points of obstruction are avoided. Installation Procedure Single Wall Construction 1. Locate the center of the roof by careful mea-

surement, remove the headlining as necessary, and drill a pilot hole down through the roof. If the interior light of the car is centered in the roof, remove this light and fixture and drill the pilot hole up through the roof at about the center of the interior light mountings. This centers the antenna mount on the roof and allows for easy access. 2. Drill a 3/4-inch hole from the top of the roof until the saw bottoms. Use a Motorola hole cutting saw (01-80382A25) or equivalent. When the saw bottoms on the roof, it cleans off the paint in a neat circle and assures good contact with the locking nut. IMPORTANT For proper seating of brushing assembly, remove burrs and scrape any foreign matter from underside of hole out to at least 1/8-inch from edge. 3. Determine the routing of the cable from the antenna mounting base to the radio set; then remove the molding and trim necessary to facilitate pulling the cable through. NOTE To ensure ease of assembly, thread the locking nut on and then off the bushing assembly before installation. This removes any burrs which may be present. Mobile 1/4-Wave Antennas 4. Refer to Figure 5. From the top, feed the RG-58A/U lead-in cable between the headlin-

ing and the metal roof. Then route the cable between the roof and the radio set. 5. Refer to Figure 6. The bushing assembly is now in a position to drop into the hole in the roof. It should be tilted at a slight angle and fed into the 3/4-inch hold. The threaded top will not fall through the hole. 6. Refer to Figure 7. Hold the antenna bushing assembly in place with the index finger and thread the locking nut onto it as shown. 7. Pull up on the bushing assembly as illustrated in Figure 8, and make sure it is centered and seated (both shoulders inside the drilled hole), and that the "O" ring is in the groove in the locking nut. (As furnished, the "O" ring has been placed in the locking nut groove and imbedded silicone grease.) Use a 15/16-inch open-end wrench to tighten the locking nut until it bottoms firmly against the roof top. in IMPORTANT Refer to Figure 3. If the bushing assembly should slip or rotate for any reason dur-

ing the tightening procedure, insert the tips of a long nose plier or spanner wrench into the two holes in the bushing assembly and apply force to prevent rotation until the locking nut is tight. The locking nut must come into contact with the car roof to insure the proper antenna radiation pattern. This can only happen when the rubber "O" ring is fully compressed. 8. Take up the slack in the cable and replace the headlining retainer molding. 9. Replace headlining and dome removed. light if Installation Procedure - Double Wall Construction Vehicles With Dome Lights or Removable Headlining 1. Remove the dome light from its mount or remove the headlining from the installation area. 2. Drill a small pilot hole centered in the roof of the vehicle. The center of the cavity where the dome light was removed is sufficiently close. 3. Using a 1-1/4-inch diameter hole saw cut a hole in the inside layer of the metal. June, 2002 6880101W80-C 3 Mobile 1/4-Wave Antennas Installation Figure 5. Coaxial Cable Insertion Figure 6. Bushing Assembly Insertion Figure 7. Locking Nut Positioning Figure 8. Locking Nut Tightening 4 6880101W80-C June, 2002 Installation Mobile 1/4-Wave Antennas 4. Remove the metal and filler from 1-1/4-inch diameter hole. this 4. Install the mount to the outside roof thickness per installation procedure given for vehicles with single wall construction. 5. Complete the installation per installation pro-

cedure given for vehicles with single wall con-

struction. A completed mount is illustrated in Figure 9. Vehicles Without Dome Lights When the vehicle has no dome light, and it is not feasi-

ble to remove the headlining to get to the inside sur-

face, proceed as follows:

1. Locate the center of the roof and make sure the area beneath this point is clear to allow passage of a drill. 2. With a 3/4-inch diameter hole cutting saw carefully cut a 3/4-inch hole from the top of the roof through both thicknesses of metal. Clean the metal in a neat circle around the hole to assure a good contact between the roof metal and the locking nut. 3. Remove any burrs and remove the filler sepa-

rating the roof thickness for a distance of 1/4-inch back from the hole. Mounting Hardware Installation Trunk Lip Mount NOTE Not recommended for transmitters with power outputs of 7 W or greater. 1. Refer to Figure 11 for antenna location. 2. Using the Allen wrench supplied, turn the two set screws counterclockwise until their threads are not visible on the underside of the clamp bracket. 3. Raise the trunk lid to pass the coaxial cable through; then tilt the mounting base slightly to hook the clamp bracket on the trunk lip. The coaxial cable, coming from under the mounting base, may have to be bent down to accomplish this step. When the base is in posi-

tion, the coaxial cable should not bind in any way, or be pinched under a set screw. 4. Tighten the two set screws. Figure 9. Roof Mount in Vehicle With Dome Light or Removable Headlining Figure 10. Roof Mount in Vehicle Without Dome Light June, 2002 6880101W80-C 5 Mobile 1/4-Wave Antennas Installation Figure 11. Typical Mount Location NOTE The coaxial cable will normally not be harmed by opening and closing the trunk, although reasonable care should be exercised. The rubber molding around the trunk lid will prevent damage to the cable. 5. Route the cable from the mounting base to the radio set. Rubber grommets should be used in any sheet metal holes through which the cable is routed. Ensure that the cable will not be pinched during normal vehicle operation. Mini-UHF Connector Installation Figure 12. Use Motorola hand tool part #66-80388A26 (Refer to Figure 12). A deluxe rachet type tool is available; order part #66-80334B40. Installation Instructions 1. Slip ferrule and collar onto cable. Refer to Figure 13. 2. Prepare cable to strip dimensions per Figure 14, which is also marked on the hand tool. 4. Crimp center contact using proper crimp section of tool. Refer to Figure 12 marked

"CENTER CONTACT."

5. Push collar forward onto plug assembly. Fit cable braid over the support sleeve of the con-

nector. Refer to Figure 13. 6. Push ferrule over braid until flange butts against connector body. Refer to Figure 13. Using the correct crimp area of the tool, crimp the ferrule close to the plug body. See Figure 12, crimp location "C." Crimp ferrule a second time close to the cable end. 3. Insert stripped cable into plug body until con-

ductor is exposed (front end) and dielectric bottoms inside body. Refer to Figure 13. 7. The protruding center conductor should be trimmed flush with the end of the center con-

tact. 6 6880101W80-C June, 2002 Frequency Conversion Mobile 1/4-Wave Antennas Plug Assembly Procedure Figure 13. Plug Assembly Procedure Figure 14. Frequency Conversion See Table 1. Antennas in each band are equipped with whip radiators cut to the proper length for that specific band. To change from one band to another, a whip assembly of the proper length should be substituted for one previously in use. Antennas in the 136-150.8 MHz range are also equipped with a spring washer

(roof mount models only; see Figure 3) to provide for proper impedance matching. Should it be desired to change from an antenna in the 136-150.8 MHz range to one in the other ranges, this washer must be removed in addition to changing the whip assembly. Con-

versely, to shift from the other ranges to the 136-

150.8 MHz range, a spring washer must be installed in addition to changing the whip assembly. Motorola Recommendations for Mobile Antenna Location Recommended mobile antenna installations are lim-

ited to metal body vehicles at the center of the roof and center of the trunk deck locations. Refer to Table 2. The antenna installation must additionally be in accor-

dance with:

the requirements of the antenna manufac-

turer/supplier

instructions in the Radio Installation manual. Antenna Location Mobile Antenna Installation Mobile Radio Operation and EME Exposure Observe the following caution and electromagnetic energy exposure (EME) statements when installing antennas:

CAUTION Use caution when installing antennas with mobile radio equipment using transmitter power of 7 W or greater. Install antennas only on metal bodied vehicles. NOTE For low-power mobile radios (less than 7 W) there are no antenna type or instal-

lation restrictions. To assure optimal radio performance and that human exposure to radio frequency electromagnetic energy is within the guidelines referenced in this document, transmit only when people inside and outside the vehi-

cle are at least the minimum distance away from a properly installed, externally-mounted antenna. Table 3 lists the minimum distance for several different ranges of rated radio power. Selecting an Antenna Site 1. Install the vehicle antenna external to the vehicle and in accordance with the require-

ments contained in this manual. June, 2002 6880101W80-C 7 Mobile 1/4-Wave Antennas Motorola Recommendations for Mobile Antenna Location 2. The best mounting location for the antenna is in the center of a large, flat conductive surface. In almost all vehicles, mounting the antenna in the center of the roof will satisfy these requirements. A good alternative location is in the center of the trunk lid. If you use the trunk lid, ensure that the trunk lid is grounded by connecting grounding straps between the trunk lid and the vehicle chassis. 3. Ensure the antenna cable can be easily routed to the radio. Ensure that the antenna cable is routed separately and not in parallel to any other vehicle wiring or mobile radio cable wiring. 4. Check the antenna location for any electrical interference. NOTE Any two metal pieces rubbing against each other (such as seat springs, shift levers, trunk and hood lids, exhaust pipes, etc.) in close proximity to the antenna can cause severe receiver inter-

ference. 5. If the vehicle is equipped with an electronic anti-lock braking system (ABS), mount the antenna at the center of the roof or trunk lid and do not route the antenna cable near the ABS Modulator Box. Mount the radio as far away from the Modulator Box as physically possible. This minimizes radio interference to the modulator box from the radio. 6. Make sure the mobile radio antenna is installed at least one foot (30.48cm) away from any other antenna on the vehicle. Table 2. Standard metal passenger vehicles Vans, pickups, and other light trucks (metal roofs) Heavy duty equipment with metal roofs (heavy duty trucks, semi-tractors, heavy refuse trucks, cement mixer trucks) Specialty vehicles (such as T-roofs, sun roofs, or convert-

ibles) Other vehicles Center roof or center trunk lid Center roof Center cab roof Center trunk lid recommended only for transmitter output of less than 7 W. Contact your Motorola Field Technical Representative. Do not install closer than the distances shown in Table 3, for the relevant transmitter output power, from occu-

pants or without proper antenna ground plane. Table 3. Rated Power and Distance Rated Power of Vehicle-installed Mobile Two-Way Radios 7 to 15 W 16 to 50 W More than 50 W Minimum Distance from Transmitting Antenna 1 Foot (30.5cm) 2 Feet (61cm) 3 Feet (91.5cm) 8 6880101W80-C June, 2002

6864110R13-O_cvr.qxd 2/21/02 12:39 PM Page 1 Motorola, The Stylized M logo, Intelligence Everywhere, Professional Radio - As Dedicated As You Are, CDM Series, CDM1550LS+, and Call Alert are trademarks of Motorola, Inc. LTR is a mark of E.F. Johnson Company. PassPort is a mark of Trident Micro Systems. 2002 Motorola, Inc. All rights reserved. Printed in U.S.A.

*6864110R13-O*

6864110R13-O CDM1550LS++ User Guide Professional Radio - As Dedicated As You Are 6864110R13-OTOC.fm Page 1 Thursday, April 4, 2002 5:52 PM CONTENTS Computer Software Copyrights . 6 Safety . 7 User Safety, Training, and General Information . 7 Compliance with RF Energy Exposure Standards. 7 Operational Instructions and Training Guidelines . 8 Transmit and Receive . 8 Mobile Antennas . 9 Approved Accessories . 9 Fixed Site Antennas . 9 Electromagnetic Interference/

Compatibility. 10 Facilities . 10 Vehicles . 10 Driver Safety . 11 Operational Warnings . 11 For Vehicles With an Air Bag . 11 Potentially Explosive Atmospheres. 11 Blasting Caps and Areas . 11 Introduction . 13 Trunked Radio Systems . 13 PassPort Trunked Systems . 13 LTR Trunked Systems . 13 Conventional Radio Systems . 14 CDM1550LS+ Radio Features . 14 Radio Wide Features . 14 PassPort Zone Features . 14 LTR Zone Features . 15 Conventional Zone Features . 15 Radio Overview . 17 Parts of the Radio . 17 CDM1550LS+ Model. 17 On/Off/Volume Control Knob . 18 LED Indicators . 18 Push-to-Talk (PTT) Button . 19 Microphone. 19 Menu/Select Button ). 19 Menu Exit/Button (. 19 Menu Buttons . 19 Display . 20 Microphone Jack . 21 Optional DTMF Microphone (RMN4026). 21 DTMF Microphone Keypad . 22 C O N T E N T S 1 English 6864110R13-OTOC.fm Page 2 Thursday, April 4, 2002 5:52 PM S T N E T N O C Programmable Buttons. 24 Audio Indicators for Programmable Buttons . 28 Getting Started . 29 Turning the Radio On or Off . 29 Adjusting the Volume . 29 Selecting a Trunked Zone and Talkgroup. 30 Sending a Trunked Call . 30 Selecting a Conventional Zone and Channel . 31 Direct Zone Access. 31 Direct Channel Access . 31 Sending a Conventional Call . 33 Receiving a Trunked or Conventional Call . 33 Repeater or Talkaround J Mode

(Conventional Operation Only) . 34 Call Light

(Trunked Operation Only). 35 Home Channel . 35 Horn and Lights . 35 To Activate Horn and Lights Programmed with Call Light

(Trunked Operation Only) . 35 To Activate Horn and Lights Programmed with Call Alert

(LTR Trunked Operation Only) . 36 Remote Monitor

(LTR Trunked and Conventional Operation Only) . 36 Passport Trunking . 39 Seamless Roaming . 39 Initial Registration . 39 Roaming and Registering Between Sites . 40 Site/Min View . 41 Roam Request . 42 To Start a Roam Request . 42 To Cancel a Roam Request . 43 Troubleshooting . 43 Radio Calls . 45 Making a Selective Call

(LTR Trunked and Conventional Operation Only) . 45 Receiving a Selective Call F

(LTR Trunked and Conventional Operation Only) . 46 Sending a Call Alert Page

(LTR Trunked and Conventional Operation Only) . 46 English 2 6864110R13-OTOC.fm Page 3 Thursday, April 4, 2002 5:52 PM Receiving a Call Alert Page

(LTR Trunked and Conventional Operation Only). 47 Radio Check

(LTR Trunked and Conventional Operation Only). 48 Sending a Status

(Conventional Operation Only) . 48 Sending a Message

(Conventional Operation Only) . 49 Receiving a Message

(Conventional Operation Only) . 50 Responding to Emergency Alerts E

(Conventional Operation Only) . 50 Decoding an Emergency Alarm . 51 Multiple Queued Emergencies. 52 Three Minute Timer . 52 After the Timer Expires . 52 Clearing an Emergency Alert E

(Conventional Operation Only) . 53 Sending an Emergency Remote Monitor

(Conventional Operation Only) . 53 Sending an Emergency Alert E

(Conventional Operation Only) . 54 Sending a Remote Monitor . 54 Selective Radio Inhibit

(Conventional Operation Only) . 55 Editing a Radio Call List K

(LTR Trunked and Conventional Operation Only) . 55 Name and Call Tone Tagging

(LTR Trunked and Conventional Operation Only) . 56 To Tag a Specific Users Name. 56 To Tag a Type of Radio Call . 57 Scan . 59 Talkback . 59 PassPort Primary Auto Group Scan

(PassPort Trunked Operation Only) . 60 PassPort Group Scan G

(PassPort Trunked Operation Only) . 60 Enabled . 60 To Start or Stop PassPort Group Scan Operation through a Preprogrammed Button . 61 To Start or stop PassPort Group Scan Operation through the Menu . 61 Auto Group Scan

(LTR Trunked Operation Only) . 61 To Start Auto Group Scan . 61 To Stop Auto Group Scan . 62 C O N T E N T S 3 English 6864110R13-OTOC.fm Page 4 Thursday, April 4, 2002 5:52 PM S T N E T N O C All Group Scan

(LTR Trunked Operation Only) . 62 To Start or Stop All Group Scan Operation through a Preprogrammed Button . 62 To Start or Stop All Group Scan Operation Through the Menu . 62 System Scan G

(LTR Trunked and Conventional Operation Only) . 63 When System Scan is Enabled . 63 To Start or Stop a System Scan Operation. 63 Deleting a Nuisance Channel/Talkgroup

(PassPort Group Scan or System Scan Operation Only) . 64 To Temporarily Delete the Channel/Talkgroup . 64 Restoring a Channel/Talkgroup Back to the Scan List . 64 Editing a Scan List

(PassPort Group Scan or System Scan Operation Only) . 64 Adding or Deleting Talkgroups or Channels in a Scan List . 65 Prioritizing a Talkgroup or Channel in a Scan List

(System Scan Operation Only) . 66 Phone . 69 Making a Phone Call D Through a Trunked System . 69 Making a Phone Call D Through a Conventional System . 70 Receiving a Phone Call D Through a Trunked or Conventional System. 72 Modifying the Phone List K . 73 To Add an Entry . 73 To Delete an Entry . 74 To Edit an Entry . 75 Voice Storage . 77 Incoming Call Recording . 78 Selective Incoming Call Recording . 78 To Selectively Record an Incoming Call . 78 All Incoming Call Recording . 78 To Record All Incoming Calls . 79 Voice Memo Recording . 80 To Record a Voice Memo using the Preprogrammed Record/Playback Button . 80 English 4 6864110R13-OTOC.fm Page 5 Thursday, April 4, 2002 5:52 PM C O N T E N T S To Record a Voice Memo using the Menu . 80 Recorded Message Playback . 81 To Playback a Message using the Prepro-

grammed Record/Playback Button . 81 To Playback a Message using the Menu . 82 Recorded Message Delete . 82 To Delete a Message using the Preprogrammed Delete Playback Button . 82 To Delete a Message using the Menu . 83 Recorded Message Transmission . 83 Answer Mode . 84 To Enable the Answer Mode Feature . 84 To Record a Message . 84 To Disable the Answer Mode Feature . 85 Audio/Tone Settings . 87 Utilities . 89 Setting the Power Level B . 91 Setting the Clock/Alarm. 92 Displaying the Time. 93 Selecting the Display Language

(LTR Trunked and Conventional Operation Only) . 93 Warranty . 95 Accessories . 99 Microphones . 99 Handsfree Kits . 99 Exchangeable Button Kits . 99 Mounting Kits . 99 Remote Mounts . 100 External Speakers . 100 Installation and Alarm Kits . 100 Antennas . 100 Service Aids and Programming Equipment Manuals . 100 Manuals . 101 Control Station Kits. 101 Mobile Data Units Section . 101 Public Address . 103 Retrofit Kit. 103 5 English 6864110R13-OTOC.fm Page 6 Thursday, April 4, 2002 5:52 PM S T N E T N O C COMPUTER SOFTWARE COPYRIGHTS The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. English 6 SAFETY USER SAFETY, TRAINING, AND GENERAL INFORMATION READ THIS IMPORTANT INFORMATION ON SAFE AND EFFICIENT OPERATION BEFORE INSTALLING AND USING YOUR MOTOROLA MOBILE TWO-WAY RADIO IN A VEHICLE OR AS A CONTROL STATION. COMPLIANCE WITH RF ENERGY EXPOSURE STANDARDS Your Motorola two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environment at duty cycles of up to 50% talk-50% listen and should be used for occupational use only. In terms of measuring RF energy for compliance with the FCC exposure guidelines, your radio radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. Note that the approved, supplied batteries for this radio are rated for a 5-5-90 duty cycle (5% talk-

5% listen - 90% standby), even though this radio complies with the FCC occupational exposure limits at duty cycles of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:

United States Federal Communications Commission, Code of Federal Regulations;

47CFR part 2 sub-part J

American National Standards Institute

(ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1- 1992 Institute of Electrical and Electronic Engineers (IEEE) C95.1- 1999 Edition International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998

Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 S A F E T Y 7 English

Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human Exposure) Standard 2001 (applicable to wireless phones only)

ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) additional requirements for SMR, cellular and PCS product certification. OPERATIONAL INSTRUCTIONS AND TRAINING GUIDELINES To ensure optimal performance and compliance with the occupational/controlled environment RF energy exposure limits in the above standards and guidelines, users should transmit no more than 50% of the time and always adhere to the following procedures:

Transmit and Receive To transmit (talk), push the Push-To-Talk

(PTT) button; to receive, release the PTT button. Transmit only when people outside the vehicle are at least the minimum lateral distance away, as shown in Table 1, from a properly installed, externally-mounted antenna. Table 1 lists the minimum lateral distance for bystanders in an uncontrolled environment from the transmitting antenna at several different ranges of rated radio power for mobile radios installed in a vehicle. Table 1: Rated Power and Lateral Distance Rated Power of Vehicle-installed Mobile Two-way Radio Less than 7 watts 7 to 15 watts 16 to 50 watts 51 to 110 watts Minimum Lateral Distance from Transmitting Antenna 8 inches

(20 centimeters) 1 foot

(30 centimeters) 2 feet

(60 centimeters) 3 feet

(90 centimeters) Y T E F A S English 8

Mobile Antennas Fixed Site Antennas Install antennas at the center of the roof or the center of the trunk deck. These mobile antenna installation guidelines are limited to metal body vehicles. The antenna installation must addition-

ally be in accordance with:

a. The requirements of the antenna manu-

facturer/supplier b. Instructions in the Radio Installation Manual

Use only Motorola approved supplied antenna or Motorola approved replace-

ment antenna. Unauthorized antennas, modifications, or attachments could dam-

age the radio and may violate FCC regula-

tions. Approved Accessories For a list of Motorola approved antennas see the appendix of this user manual. If mobile radio equipment is installed at a fixed location and operated as a control station or as a fixed unit, the antenna installation must comply with the following requirements in order to ensure optimal performance and compliance with the RF energy exposure limits in the above standards and guidelines.

The antenna should be mounted outside the building on the roof or a tower if at all possible.

As with all fixed site an tenna installations, it is the responsibility of the licensee to man-

age the site in accordance with applicable regulatory requirements and may require additional compliance actions such as site survey measurements, signage, and site access restrictions in order to insure that exposure limits are not exceeded. S A F E T Y 9 English

Y T E F A S ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY NOTE: Nearly every electronic device is sus-

ceptible to electromagnetic interfer-

ence (EMI) if inadequately shielded, designed or otherwise configured for electromagnetic compatibility. It may be necessary to conduct compatibility testing to determine if any electronic equipment used in or around vehicles or near fixed antenna sites is sensitive to external RF energy and if any proce-

dures need to be followed to eliminate or mitigate the potential for interaction between the radio transmitter and the equipment or device. Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Vehicles To avoid possible interaction between the radio transmitter and any vehicle electronic control modules, for example, ABS, engine, or transmission controls, we recommend that the radio be installed by an experienced installer and that the following precautions be used when installing the radio:

1. Refer to any manufacturers instructions or other technical bulletins or recommendations on radio installation. 2. Before installing the radio, determine the location of the electronic control modules and their harnesses in the vehicle. 3. Route all radio wiring, including the antenna transmission line, as far away as possible from the electronic control units and associated wiring. English 10 Driver Safety Potentially Explosive Atmospheres Check the laws and regulations on the use of radios in the area where you drive. Always obey them. When using your radio while driving, please:

Give full attention to driving and to the road.

Pull off the road and park before making or answering a call if driving conditions so require. OPERATIONAL WARNINGS For Vehicles With an Air Bag

W A R N I N G Do not place a mobile radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a mobile radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. Turn off your radio prior to entering any area with a potentially explosive atmosphere. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles, such as grain, dust or metal powders, and any other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are often but not always posted. Blasting Caps and Areas To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: Turn off two-way radio. Obey all signs and instructions. For radios installed in vehicles fuelled by liquefied petroleum gas, refer to the (U.S.) S A F E T Y 11 English National Fire Protection Association standard, NFPA 58, for storage, handling, and/ or container information. For a copy of the LP-

gas standard, NFPA 58, contact the National Fire Protection Association, One Battery Park, Quincy, MA. Y T E F A S English 12 INTRODUCTION Welcome to Motorolas CDM Series family of radio users. The CDM1550LS +, the Intelligent Radio, combines the very latest in two-way technology while delivering outstanding functionality at the touch of a button. The CDM1550LS + mobile radio operates on PassPort and LTR trunked and conventional radio systems. TRUNKED RADIO SYSTEMS Trunked systems allow a large number of users to share a relatively small number of frequencies or repeaters without interfering with each other. The airtime of all the repeaters in a trunked system is pooled, which maximizes the amount of airtime available to any one radio and minimizes channel congestion. PassPort Trunked Systems PassPort is an enhanced trunking protocol developed by Trident Micro Systems that supports wide area dispatch networking. A network is formed by linking several trunked sites together to form a single system. This offers users an extended communication coverage area. Additionally, users with PassPort can seamlessly roam among all sites within the network. Seamless roaming means that the radio user does not have to manually change the zones on the radio when roaming from site-to-site. LTR Trunked Systems LTR is a transmission based trunking protocol developed by the E. F. Johnson Company for primarily single site trunking applications. In transmission trunking, a repeater is used for only the duration of a single transmission. Once a transmission is completed, that repeater becomes available to other users. This means that a conversation comprised of many transmissions may occur over several different channels within the LTR system. This method of trunking provides system efficiency I N T R O D U C T O N I 13 English by making repeaters available to all users after every transmission. CONVENTIONAL RADIO SYSTEMS Conventional radio systems typically refers to unit-to-unit communications through a single channel. Conventional systems also allow radio users to extend communication coverage by relaying their messages through a repeater. To ensure coordinated use by multiple talkgroups, each radio user must monitor the channel or repeater before transmitting to verify that the system is not currently busy. CDM1550LS + RADIO FEATURES Note: Throughout this manual there are features listed as trunked and con-

ventional. Trunked indicates the fea-

ture functions in both PassPort and LTR zones unless otherwise noted. Conventional indicates the feature functions in Conventional zones only. CDM1550LS + Radio Feature Highlights:

Radio Wide Features 14-Character Alphanumeric Display 4 Programmable Feature Buttons Up to 15 PassPort and/or LTR Zones with up to 16 Talkgroups per Zone Up to 16 Conventional Channels X-Pand Audio Enhancement Selectable by Conventional Channel, LTR Repeater or PassPort Talkgroup Home Channel Telephone Interconnect User-programmable Phone and Scan Lists Voice Storage Capability PassPort Zone Features Unique Mobile Identity Number per Radio Unique Electronic Serial Number per Radio Registration/Deregistration upon power up/

power down Automatic Seamless Roaming between Networked Sites Registered Site and Mobile Identity View User Initiated Roam Request PassPort Primary Group Auto Scan and PassPort Scan I N O T C U D O R T N I English 14

PassPort Zone Features (Cont.) Call Signalling Features

- PTT ID (Display of Mobile Identification Number) LTR Zone Features

MDC 1200 Signaling

- Call Alert

- Selective Call

- Radio Check

- Caller ID Auto Group System, All Group Scan System Scan with 2 Priority Levels Conventional Zone Features

Monitor and Sticky Permanent Monitor System Scan with 2 Priority Levels I N T R O D U C T O N I 15 English

Notes I N O T C U D O R T N I English 16 03_Radio Overview.fm Page 17 Tuesday, April 2, 2002 5:48 PM RADIO OVERVIEW PARTS OF THE RADIO CDM1550LS+ Model On/Off/Volume Control Knob Red/Yellow/Green LED Indicators LCD Screen Talkgroup/Channel Selector/

Menu Navigation Buttons

(Up/Down) Menu Exit/Escape Button Menu Enter/Select Button I R A D O O V E R V E W I Programmable Button 3 (P3)

(Interchangeable) Microphone Jack Programmable Button 1 (P1)

(Interchangeable) Programmable Button 2 (P2)

(Interchangeable) Zone Selector/

Editing Buttons

(Left/Right) Programmable Button 4 (P4)

(Interchangeable) 17 English I W E V R E V O O D A R I 03_Radio Overview.fm Page 18 Tuesday, April 2, 2002 5:48 PM On/Off/Volume Control Knob Turns the radio on or off, and adjusts the radios volume. LED Indicators Indicates power-up, scan, or receipt of a talkgroup or selective call (see table below):

LED Color Steady red Flashing red Indicates Radio is transmitting (PTT button pressed) Radio is attempting to access trunked system (PTT button pressed), or Radio is receiving (PTT button released) Double flashing yellow Call Light feature, or Individual Selective Call Received Single flashing yellow Group Selective call received

(LTR trunked and conventional operation only) Momentary green Radio has powered-up successfully LED Color Indicates Double flashing green System, All Group Scan or PassPort Group Scan Operation Left Button v and Right Button w

Used to scroll through the preprogrammed trunked and conventional zones.

Used to scroll through menu choices when in Menu Mode.

When editing Call, Scan, and Phone lists, v is used as a backspace key and w is used to add a space. Up Button y and Down Button z

Used to scroll through the preprogrammed talkgroups of a selected trunked zone, or through conventional channels when in conventional zone.

Used to scroll through menu choices when in Menu Mode. English 18 03_Radio Overview.fm Page 19 Tuesday, April 2, 2002 5:48 PM Push-to-Talk (PTT) Button Press and hold down this button to talk;

release it to listen. Menu Buttons Exit Up Menu/

Select Microphone When sending a message, hold the microphone 1 to 2 inches (2.5 to 5 cm) away from your mouth, and speak clearly into the microphone. Menu/Select Button ) Used to enter Menu Mode. When in Menu Mode, this button is used to make menu selections. Menu Exit/Button (

Used to move to the previous Menu level (short press) or to exit Menu Mode (long press). Left Down Right I R A D O O V E R V E W I 19 English 03_Radio Overview.fm Page 20 Tuesday, April 2, 2002 5:48 PM Display Symbol Indication I W E V R E V O O D A R I The top display row displays menu and radio status information:

Indication The X-Pand feature is activated. When in narrow band, this feature improves audio quality. Low Power R or High Power S is activated. G Scan H

Priority 1 Scan

( flashing) The selected channel is being monitored (conventional operation only). Phone mode is selected. H Priority 2 Scan

( steady) A Selective Call or Call Alert has been received . Symbol A X-Pand B Power Level C Monitor D Phone F Call Received 20 English When the green LED is blinking, indicates that the System, PassPort Scan, or All Group Scan feature has been activated. When the green LED is off, indicates that non-prioritized Auto Group Scan has been activated. Indicates activity on a priority 1 talkgroup or channel during System Scan.

When the green LED is on, indicates activity on a priority 2 talkgroup or channel during System Scan.

When the green LED is off, indicates prioritized Auto Group Scan has been activated. 03_Radio Overview.fm Page 21 Tuesday, April 2, 2002 5:48 PM Symbol Indication J Talkaround You are not transmitting through a repeater

(Conventional operation only). K Programming Mode U Clock M Signal Strength N PassPort Zone A Program list is being edited. Shows the time (12- or 24-hour). The more bars, the stronger the signal being received by your radio. A PassPort zone has been selected. Microphone Jack Plug the optional DTMF Microphone

(RMN4026) or other microphone into this jack. Push-to-Talk

(PTT) Button OPTIONAL DTMF MICROPHONE

(RMN4026) Your radio may be ordered with an optional DTMF (Dual-Tone Multi-Frequency) microphone that has a direct-entry keypad. This microphone has three buttons (A, B, C) below the keypad that can be programmed by your dealer to conveniently activate available radio features. I R A D O O V E R V E W I Microphone Keypad Programmable Buttons

(A, B, C) 21 English 03_Radio Overview.fm Page 22 Tuesday, April 2, 2002 5:48 PM DTMF Microphone Keypad 1 2 3 4 5 6 7 8 9

* 0 #

A B C I W E V R E V O O D A R I The keypad is used for:

Dialing a phone number

Entering a specific radio ID number when making an MDC radio call

Entering information when programming radio call, scan, and phone lists.

Directly accessing preprogrammed features

, page 24])

, and buttons [see Each key can generate several different characters. For example, to enter the character C, press the 2 button three times. (Refer to the following table on page 23.) English 22 03_Radio Overview.fm Page 23 Tuesday, April 2, 2002 5:48 PM Entering Characters Using the DTMF Microphone Keypad Number of Times Button is Pressed Button 1 0 0 1 1 2 A 3 D 4 G 5 J 6 M 7 P 8 T 9 W

2

B E H K N Q U X

Blank Space 3

C F I L O R V Y

4

2 3 4 5 6 S 8 Z

. 5

a d g j m 7 t 9

6 7 8 9 10 11 12 13 14 15 b e h k n p u w

c f i l o q v x 2 3 4 5 6 r 8 y s z 7 9

y Y

I R A D O O V E R V E W I 23 English I W E V R E V O O D A R I 03_Radio Overview.fm Page 24 Tuesday, April 2, 2002 5:48 PM PROGRAMMABLE BUTTONS Your radio has several programmable buttons that can be programmed by your dealer as shortcuts to various radios features. Programmable buttons include:

The four front buttons (P1, P2, P3, and P4).

The three buttons (A. B, and C) of the optional DTMF microphone. Some buttons can access up to two features, depending on the type of button press:

Short Pressquickly pressing and releasing the programmable buttons, or Long Presspressing and holding the programmable buttons, or

Hold Downpressing and holding down the programmable buttons while checking status or making adjustments. The table on page 25 summarizes the programmable features available and shows the page number where the feature is explained. In the Button column, have your dealer record the name of the programmable button next to the feature that has been programmed to them. Use the abbreviations for instance P1, P2, P3, and P4 shown in the radio illustrations at the front of this manual. Also, where a choice exists, have your dealer indicate whether the button press is short press (SP), or long press (LP). Check with your dealer for a complete list of features your radio supports. English 24

03_Radio Overview.fm Page 25 Tuesday, April 2, 2002 5:48 PM Programmable Features Feature Indicator Short Press Long Press Hold Down Page Button Home Channel Backlight Control Monitor Phone Power Level Radio Call Repeater/

Talkaround C D B LED Color J Roam Request* Searching Scan/Delete Nuisance Channel G Directly access your favorite trunked zone and talkgroup or conventional channel. Turn on your radio backlight. Enter/Exit perma-

nent monitor mode. Directly access Phone mode. Open Squelch. Toggle transmit power level between high and low. Directly access radio call menu. Toggle between using a conventional repeater or transmitting directly to another radio. Manually initiate PassPort roaming function. Turn PassPort Group, All Group, and System scan on or off. Stop PassPort roaming function. Delete a nuisance channel while scanning. Continually monitor channel. 35 71 93 47 34 42 66 This feature is activated by EITHER a short OR a long press, but not both. Conventional operation only. LTR trunked operation only. *PassPort trunked operation only. I R A D O O V E R V E W I 25 English I W E V R E V O O D A R I 03_Radio Overview.fm Page 26 Tuesday, April 2, 2002 5:48 PM Feature Indicator Short Press Long Press Hold Down Page Button Programmable Features (Continued) Site/MIN View*

Speed Dial Voice Storage Record/Playback Voice Storage Playback Exit Voice Storage Playback Delete Volume Set Edit Scan List Displays the PassPort site number on which the unit is registered, the home site and units MIN (Mobile Identity Number). Quickly access speed dial phone list. Playback recorded messages. Record voice memos. Exit Voice Storage Play Back mode. Delete recorded messages. Sound a tone for adjusting your radios volume level. 41 71 82 83 84 29 66 Add, delete, or prioritize talkgroups or channels. Direct entry to zone selection menu. Direct Zone Access This feature is activated by EITHER a short OR a long press, but not both. Conventional operation only. LTR trunked operation only. *PassPort trunked operation only. 31 English 26 03_Radio Overview.fm Page 27 Tuesday, April 2, 2002 5:48 PM Feature Indicator Short Press Long Press Hold Down Page Button Programmable Features (Continued) Direct Channel Access Horn and Lights Auxiliary Control (1/2) Status Message Emergency E Direct access to a trunked talkgroup or conventional channel through a Smart Microphone Toggles external alarm feature or cancels a triggered alarm. Activates or deactivates a pin on the accessory connector. Direct entry to the message menu. Direct entry to the message menu. Initiate Emergency Alert Cancel Emergency Alert 31 35 50 51 56 This feature is activated by EITHER a short OR a long press, but not both. Conventional operation only. LTR trunked operation only. *PassPort trunked operation only. I R A D O O V E R V E W I 27 English 03_Radio Overview.fm Page 28 Tuesday, April 2, 2002 5:48 PM Audio Indicators for Programmable Buttons High-Low Tone Low-High Tone In addition to having visual indicators, some programmable buttons use tones to indicate one of two modes:

Button High-Low Tone Low-High Tone Scan Power Level Repeater/

Talkaround Stop scan High power selected Uses conventional repeater Start scan Low power selected Does not use conventional repeater I W E V R E V O O D A R I English 28 ADJUSTING THE VOLUME Turn the On/Off/Volume Control knob clockwise to increase the volume, or counterclockwise to decrease the volume. or 1 2 3 Hold down the Volume Set button (see page 26). You hear a continuous tone. Turn the On/Off/Volume Control knob to the desired volume level. Release the Volume Set button. 04_GetStarted.fm Page 29 Tuesday, April 2, 2002 4:38 PM GETTING STARTED TURNING THE RADIO ON OR OFF On/Off/Volume Control Knob ON Push the On/Off/

Volume Control knob. If power-up is successful, you hear the Self-Test Pass Tone OFF Push the On/Off/

Volume Control knob until you hear a click and the display clears. and see the LED momentarily turn green. If the radio fails to power up, you hear the Self-Test Fail Tone

. I G E T T N G S T A R T E D 29 English 04_GetStarted.fm Page 30 Tuesday, April 2, 2002 4:38 PM SELECTING A TRUNKED ZONE AND TALKGROUP SENDING A TRUNKED CALL To Send a Trunked Call Note: Throughout this manual there are features listed as trunked and con-

ventional. Trunked indicates the fea-

ture functions in both PassPort and LTR zones unless otherwise noted. Conventional indicates the feature functions in Conventional zones only. Up to 15 PassPort and/or LTR trunked zones

(containing 16 talkgroups each) can be programmed into your radio. To select a trunked zone and talkgroup:

1 v or w to select the appropriate trunked zone. 2 y or z until you see the desired preprogrammed talkgroup on the display. Note: N (the PassPort Zone symbol) appears when a PassPort Zone has been selected. 1 Hold the microphone in a vertical position at a distance of about 1 to 2 inches (2.5 to 5 cm) from your mouth. 2 Press and hold the PTT button. or Press and release the PTT button and wait 3 seconds. If access to the trunked system was successful, the red LED indicator lights steady.

In addition, your dealer can program your radio to sound a short, high-pitched (talk permit) tone, indicating successful trunked system access. If access to the trunked system was unsuccessful, the red LED indicator flashes and a low-pitched (talk prohibit) tone sounds, indicating that the system was busy or out-of-range. D E T R A T S G N T T E G I English 30

04_GetStarted.fm Page 31 Tuesday, April 2, 2002 4:38 PM 3 With the PTT button depressed, speak clearly into the microphone 4 Release the PTT button to listen. SELECTING A CONVENTIONAL ZONE AND CHANNEL Up to a total of 16 conventional channels, in one or more conventional zones, can be programmed into your radio. To Select a Conventional Zone and Channel 1 v or w to select the appropriate conventional zone. 2 y or z until you see the desired conventional channel on the display. DIRECT ZONE ACCESS The Direct Zone Access feature offers an alternative way of accessing a trunked or conventional zone. To Activate Direct Zone Access 1 Press the preprogrammed Direct Zone Access button (see page 27). 2 y or z until you see the desired zone on the display. 3 u to confirm your selection. DIRECT CHANNEL ACCESS The direct channel access feature allows you to directly access a specific trunked talkgroup or conventional channel within the zone you have currently selected. This feature can be programmed on one of the radio programmable buttons (P1, P2, P3 or P4) and/

or any DTMF microphone (RMN4026) programmable buttons (A, B or C). I G E T T N G S T A R T E D 31 English 04_GetStarted.fm Page 32 Tuesday, April 2, 2002 4:38 PM To Start Activate Direct Channel Access Using the DTMF microphone:

Using the radios programmable buttons:

1 Press the preprogrammed Direct Channel button. The current talkgroup or channel flashes intermittently. 1 Press the preprogrammed Direct Channel button (A, B, or C). The current talkgroup or channel flashes intermittently. YR TKGP ALIAS YR TKGP ALIAS 2 Up or down arrow y or z to select the appropriate Trunked talkgroup or channel. 3 Press again the preprogrammed Direct Channel button. or Press y or z The new selected talkgroup or channel appears on the display NW TKGP ALIAS 2 Up or down arrow y or z to select the appropriate Trunked talkgroup or channel. or If Menu/Channel Up feature is preprogrammed on the DTMF microphone press it to select the appropriate talkgroup or channel. 3 Press again the preprogrammed Direct Channel button. or Press select/enter button on the micro-

phone (if preprogrammed). The new selected talkgroup or channel appears on the display. NW TKGP ALIAS D E T R A T S G N T T E G I English 32 04_GetStarted.fm Page 33 Tuesday, April 2, 2002 4:38 PM SENDING A CONVENTIONAL CALL Note:

In the United States, FCC regulations require you to monitor the conventional channels before sending a call. The monitor feature (see page 25) can be accessed through one of your programmable buttons. To send a conventional call:

1 Hold the microphone in a vertical position at a distance of about 1 to 2 inches (2.5 to 5 cm) from your mouth. 2 Press the PTT button and speak clearly into the microphone. The red LED indica-

tor lights steady while the call is being sent. 3 Release the PTT button to listen. RECEIVING A TRUNKED OR CONVENTIONAL CALL 1 Turn your radio on. 2 Adjust your radios volume (see page 29). 3 v or w to select the desired trunked or conventional zone, then y or z until you see the desired preprogrammed talkgroup or conventional channel on the display.

Make sure the PTT button is released. 4 Listen for voice activity. The red LED indi-

cator flashes when your radio is receiv-

ing. Note:

In PassPort mode, the Mobile Identity Number (XXXX) of the calling radio appears on the display if enabled. XXXX I G E T T N G S T A R T E D 33 English 04_GetStarted.fm Page 34 Tuesday, April 2, 2002 4:38 PM or 1 ) to enter Menu Mode. 2 y or z until Rptr/Talkarnd 3 ) to select Rptr/Talkarnd 4 y or z until Talkarnd Mode or Talkarnd Mode 5 ) to confirm your selection. REPEATER OR TALKAROUND J MODE

(CONVENTIONAL OPERATION ONLY) Talkaround Mode enables you to communicate with another radio when either:

The repeater is not operating or

Your radio is out of the repeaters range but within communicating distance of another radio. Note: The J symbol appears on the LCD screen when Talkaround Mode is selected. To Select either Repeater Mode or Talkaround Mode Press the preprogrammed Repeater/

Talkaround button (see page 25) to toggle between Repeater Mode and Talkaround Mode. D E T R A T S G N T T E G I English 34 04_GetStarted.fm Page 35 Tuesday, April 2, 2002 4:38 PM CALL LIGHT

(TRUNKED OPERATION ONLY) The Call Light indicator informs you that you have received a call from a specified talkgroup

(as programmed by your dealer). The yellow LED indicator flashes continuously, indicating that a call has been received. To Turn the Call Light Off

Turn the radio off, then on again.

Select another trunked or conventional zone.

Press the PTT button.

Press any preprogrammed button. HOME CHANNEL The Home Channel feature allows you to instantly access your favorite trunked talkgroup or channel at the touch of a button. To Activate Home Channel Press the preprogrammed Home Channel button (see page 25). HORN AND LIGHTS When you are away from your vehicle, the Horn and Lights feature notifies you when a call is received by activating your vehicles horn and lights. This feature can be triggered by a call alert in LTR mode. It also can be associated with call light in LTR and PassPort mode. To Activate Horn and Lights Programmed with Call Light (Trunked Operation Only) 1 Press the preprogrammed Horn and Lights button. The LED flashes yellow continuously, indicating that a call has been received. you see YR CURRENT TKGP 2 Once the delay timer has expired, the horn and lights of the vehicle go off. 3 Press any buttons on the radio or the DTMF microphone to deactivate it. I G E T T N G S T A R T E D 35 English 04_GetStarted.fm Page 36 Tuesday, April 2, 2002 4:38 PM To Activate Horn and Lights Programmed with Call Alert

(LTR Trunked Operation Only) REMOTE MONITOR

(LTR TRUNKED AND CONVENTIONAL OPERATION ONLY) 1 Press the preprogrammed Horn and Lights button. When you receive a call alert, you can see the preprogrammed name or ID of the calling radio:

YOUR NAME OR ID Note:

If preprogrammed, alert tones (either once or continuously) may sound. 2 Press any buttons on the radio or the DTMF microphone to deactivate it. Note: There are options available in the CPS (Customer Programming Software), which dont require you to manually activate Horn and Lights. Please see your dealer for additional information. Remote Monitor allows you to automatically key-up another radio to listen-in on all surrounding audio. This feature can be initiated by a dispatcher to a mobile radio, or from a mobile radio to another mobile radio. To Activate Remote Monitor 1 ) to enter Menu Mode. 2 y or z until Radio Call 3 ) to select Radio Call 4 y or z until Remote Monitor 5 ) to select the appropriate call list member:

MDC CALL 01 Note: An audio or visual indication may come up on the receiving radio if preprogrammed by your dealer. D E T R A T S G N T T E G I English 36 04_GetStarted.fm Page 37 Tuesday, April 2, 2002 4:38 PM To cancel Remote Monitor, press any button on the radio. Note: Remote monitor automatically ceases after one transmit and one receive cycle. I G E T T N G S T A R T E D 37 English 04_GetStarted.fm Page 38 Tuesday, April 2, 2002 4:38 PM Notes D E T R A T S G N T T E G I English 38 PASSPORT TRUNKING you with optimal audio quality throughout your communications. PassPort is an enhanced, wide-area trunking protocol developed by Trident Micro Systems. Up to 128 trunked sites can be linked together to form one PassPort system, which means that your communications can extend far beyond the reach of a single trunked site. SEAMLESS ROAMING PassPort Trunking systems offer you the ability to seamlessly roam among all sites in a network. Seamless Roaming means that you do not have to manually change the zones on the radio when roaming from site-to-site. As you roam throughout a PassPort Systems coverage area, your CDM1550LS + radio is regularly monitoring the RSSI (Received Signal Strength Indication) level of the site on which you are currently registered. In addition, if the signal strength falls below the acceptable threshold pre-programmed by your dealer, your radio starts monitoring the RSSI level of adjacent sites within the network. This allows the CDM1550LS + radio to quickly roam to the site with the strongest signal, which provides Initial Registration Before communications with your talkgroup can begin, your radio needs to register on the PassPort system. Registration automatically takes place upon radio power up or after selecting the desired PassPort zone on the selector knob. What you see:

1 Upon radio Power up, you see:

(if you select a PassPort zone after the radio is powered up, see step 2). PASSPORT 2 The selected PassPort zone alias appears on the display. YOUR ZONE ALIAS 3 The selected Talkgroup Alias appears on the display. TLKGRP ALIAS T R U N K N G P A S S P O R T I 39 English Note: If the radio performs a more extensive frequency search in order to attempt successful registration, you may see on the display:

SEARCHING 4 Upon successful PassPort Registration, you see:

REG SITE XXX Note: Your radio sounds a Low-High tone upon successful PassPort System registra-

tion. The XXX number indicates the site within the PassPort system on which you have regis-

tered. TLKGRP ALIAS After successfully registering at a site, the selected PassPort talkgroup alias appears and remains on the display. 5 40 Roaming and Registering Between Sites Once initial registration with the PassPort system has occurred, your radio constantly monitors the RSSI to ensure an acceptable signal level is maintained (as programmed by your dealer). When the RSSI in the radio falls below this acceptable level, the CDM1550LS +

attempts to roam to and register onto another site within the PassPort system. This process happens automatically and requires no action by you. What you see:

1 When the radio is searching for a new site or attempting successful registration to a site, you see on the display:

SEARCHING Note: This message is displayed until suc-

cessful registration. 2 When the radio has successfully regis-

tered to the new PassPort System, XXX indicates the site number you see on the display. REG SITE XXX I T R O P S S A P G N K N U R T English The display indicates the Home Site Number (HSID) and Mobile Identity Number. IAM XXX-YYYYY XXX indicates the HSID, YYYYY indi-

cates the MIN. Note:

This message can be activated if the radio is not registered. 3 The selected PassPort talkgroup alias appears and remains on the display. TLKGRP ALIAS SITE/MIN VIEW There may be circumstances when you want to view the number of the PassPort site on which you are registered as well as your Mobile Identity Number (MIN). To Start And Stop Viewing Site/Min 1 Press the preprogrammed SITE/MIN View button (see page 26). The display shows the number of the site on which you are currently registered. site now XXX Note: If the preprogrammed button is acti-

vated prior to or during registration, a bad key chirp is sounded and you see on the display:

site now n/a T R U N K N G P A S S P O R T I 41 English ROAM REQUEST Because of the RSSI feature, the CDM1550LS + radio automatically roams to a different site when the signal from the registered site becomes too weak for quality communication. This RSSI threshold is programmed by your dealer. However, if you believe the signal strength would be better on another site, you may want to manually initiate the roaming process. This feature is called Roam Request. To Start a Roam Request 1 Press the preprogrammed Roam Request button (see page 25). 2 When the radio is searching for a new site or attempting successful registration to a site, you see on the display:

SEARCHING 3 When the radio has successfully regis-

tered to the new PassPort System, you see on the display:

REG SITE XXX Note: A bad key chirp may sound and you see on the display:

Roam Not Avail

When registration to a site with a higher RSSI than your current site is unavailable.

When the preprogrammed button is pressed before the radio has collected its neighbor list. A Neighbor list is a list of frequencies from adjoining sites within the PassPort system that are used during the roam process.

When the radio is programmed for a single home system. In these cases, wait a few seconds and try again. I T R O P S S A P G N K N U R T English 42 4 The selected PassPort talkgroup alias appears and remains on the display:

TLKGRP ALIAS To Cancel a Roam Request 1 Press and hold the preprogrammed Roam Request button (see page 25) again. You see:

Cncl Roam Req DISABLED Note: The radio then attempts to return to the previously registered site. TROUBLESHOOTING While in PassPort zones, there are some specific display messages that indicate you should contact your dealer for assistance. Message What it Means Invalid Group ID Your dealer needs to verify talk-

group programming in your radio or the PassPort system. Your radio requires reactivation on the PassPort system (not applicable to conventional and LTR functionality). Blank display upon power up . Your radio needs to be returned to your dealer for reactivation or service. T R U N K N G P A S S P O R T I 43 English Notes:

I T R O P S S A P G N K N U R T English 44 I R A D O C A L L S RADIO CALLS MAKING A SELECTIVE CALL

(LTR TRUNKED AND CONVENTIONAL OPERATION ONLY) You can make a selective call to a particular radio or to a group of radios, as programmed by your dealer. To Make a Selective Call Press the preprogrammed Radio Call button

(see page 25), and proceed to step 4. or 1 ) to enter menu mode. 2 y or z until Radio Call 3 ) to select Radio Call 6 y or z to locate the desired ID in the Radio Call List. or Enter with the DTMF microphone the ID number of the radio you want to call. 7 Press the PTT button to send the call. The radio sounds a continuous tone, if programmed by your dealer.

The LED lights a solid yellow. 8 Press the PTT button and talk; release the PTT button to listen. If not received, you see:

No Acknowledge 9 ( to return to Selective Call 4 y or z until Selective Call or 5 ) to select Selective Call Hold down ( to exit menu mode. 45 English S L L A C O D A R I RECEIVING A SELECTIVE CALL F

(LTR TRUNKED AND CONVENTIONAL OPERATION ONLY) When you Receive a Selective Call

The display shows F and the prepro-

grammed name or ID of the calling radio.

The LED indicator flashes yellow, if pro-

grammed by your dealer.

You hear an alert tone. To answer the call, press the PTT button. Note:

Unless you make a Selective Call back to the caller, your response is heard by all members of your talkgroup. SENDING A CALL ALERT PAGE

(LTR TRUNKED AND CONVENTIONAL OPERATION ONLY) To Send a Call Alert Page Press the preprogrammed Radio Call button

(see page 25) and proceed to step 4:

1 ) to enter menu mode. 2 y or z until Radio Call 3 ) to select Radio Call 4 y or z until Call Alert 5 ) to select Call Alert 6 y or z to locate the desired ID in the Radio Call List. or Enter with the DTMFmicrophone the ID number of the radio you want to page. You can alert another person by sending a Call Alert page. 7 Press the PTT button, English 46 you see:

Call in Prog and the preprogrammed name or ID alternating on the display.

The LED alternates between a solid yellow and solid red while the call is in process. RECEIVING A CALL ALERT PAGE

(LTR TRUNKED AND CONVENTIONAL OPERATION ONLY) When You Receive a Call Alert Page

The display shows F and the preprogrammed name or ID of the calling radio. Call Received I R A D O C A L L S 8 If the Call Alert page is received by the target radio, you see:

Acknowledge

You hear four alert tones, either once or continuously, as programmed by your dealer. If not received, you see:

No Acknowledge

The radio sounds a short alert tone if, programmed by your dealer. 9 ( to return to Call Alert or Hold down ( to exit menu mode.

The LED indicator flashes a single yellow for a group call, or flashes a double yellow for an individual call. To answer the page, press the PTT button; to cancel the page, press any other button. Note:

Your radio displays only the last Call Alert page received. Also, your radio does not receive any Selective Calls until you clear the page. 47 English S L L A C O D A R I RADIO CHECK

(LTR TRUNKED AND CONVENTIONAL OPERATION ONLY) Radio Check allows you to determine if a radio is within the range of the trunked system and turned on, without disturbing the user of that radio. This feature can also be used when attempts with Selective Call and Call Alert fail. To Perform a Radio Check 1 ) to enter menu mode. 2 y or z until Radio Call 3 ) to select Radio Call 4 y or z until Radio Check 5 ) to select Radio Check 6 y or z to locate the desired ID in the Radio Call list or Enter the ID number of the radio you are checking. 7 Press the PTT button, you see:

Call In Prog 8 If the Radio Check is received by the tar-

get radio, you see:

Acknowledge If not received, you see:

No Acknowledge 9 ( to return to or Radio Call Hold down ( to exit menu mode. SENDING A STATUS

(CONVENTIONAL OPERATION ONLY) This feature gives you the ability to send a status update to the base. The status feature makes more efficient use of the channel compared to voice transmissions. Status updates of up to 14 characters may be programmed by your dealer. English 48 SENDING A MESSAGE

(CONVENTIONAL OPERATION ONLY) This feature gives you the ability to send and receive preprogrammed messages. Data messages make more efficient use of channels compared to voice transmissions. Messages of up to 14 characters may be programmed by your dealer. To Send an Electronic (Data) Message 1 ) to enter Menu Mode. 2 y or z until Message 3 ) to select Message To Send a Status 1 ) to enter Menu Mode. 2 y or z until 3 ) to select Status Status 4 y or z to locate the desired status in the preprogrammed list. or when using the enhanced keypad microphone only, enter the number of the status you wish to send. or if programmed by your dealer (see page 27), press the button that has been preprogrammed for a specific status. Note: You cannot retransmit the current status update. I R A D O C A L L S 49 English S L L A C O D A R I 4 y or z to locate the desired message in the preprogrammed list. or when using the enhanced keypad microphone only, enter the number of the message you wish to send. or if programmed by your dealer (see page 27), press the button that has been preprogrammed for a specific message. RECEIVING A MESSAGE

(CONVENTIONAL OPERATION ONLY) When your radio receives a message:

You hear two alert tones.

The yellow LED indicator flashes.

You see:

Msg Received alternating with the preprogrammed alias. Note:

If you receive a message that is programmed into your radio, the display will alternate with the following:

and Message #_ No Alias RESPONDING TO EMERGENCY ALERTS E

(CONVENTIONAL OPERATION ONLY) Your radio offers choices for initiating and responding to Emergency Alert communications. Choices may include:

Emergency Cycles - Allows the radio to automatically cycle between transmit and receive mode over a preprogrammed number of times by keying with voice after it English 50 I R A D O C A L L S has received an Acknowledge to the alarm you send. The default number of transmits is one (10, maximum); the default value of the retransmit interval is 5 seconds (one, minimum; 60, maximum).

Emergency Alarm/Call - Gives you access to a voice resource, on a priority basis, over all other types of call traffic.

Emergency Remote Monitor - Enables the dispatcher to activate the transmit circuit of your radio, during an Emergency, to hear the situation through your microphone. See page 53 for more about sending an Emergency Remote Monitor.

Remote Monitor - Enables the dispatcher to activate the transmit circuit of your radio, during a normal dispatch, to hear the situation through your microphone. See page 54 for information about sending a Remote Monitor. Note: All the choices listed above are dealer preprogrammed. See your dealer for more details. Decoding an Emergency Alarm If preprogrammed by your dealer, and provided the signaling protocol supports it, your radio decodes (responds to) an Emergency Alarm or Emergency Call by:

Sounding a unique, repeating alert tone

Activating an external alarm

Displaying alternating message parts on a single line, similar to the following example E E m e r g e n c y the word Emergency, followed by E M D C C A L L 0 1

Emergency Alias from the Radio Call List

(example, MDC CALL 01), followed by 51 English

S L L A C O D A R I

Timestamp of the Emergency Alert (exam-

ple, 03:55). activate the external alarm, or display updated information. After the Timer Expires If the three-minute timer has expired for a specific Emergency Alias or ID, and the radio decodes an Emergency that is currently in queue, the radio:

Acknowledges the Emergency

Restarts the Emergency Alert tone

Activates the external alarm

Updates the time stamp on the matching Emergency Note:

If the Radio Call List does not include an alias for the radio ID, the ID displays. Radios that do not support the signaling protocol sound the alert tone, activate the external alarm and display data. E 0 3 : 5 5

Flashing the E icon (while decoding only;

lights steady when encoding) Multiple Queued Emergencies Clearing the existing displayed Emergency shows the next in the queue, if one exists.The display updates and shows Emerg (queued number) of (total number). If no additional Emergencies are queued, the radio exits Emergency mode and resumes normal mode. Three Minute Timer Responding to an Emergency starts a three-

minute timer. The radio does not generate another Emergency Alert tone against that Emergency Alias or ID until the three-minute period expires. If cleared within 3 minutes, the alarm will regenerate the alert. If the radio receives another Emergency Alert from the same Alias or ID, the radio acknowledges the Emergency but does not restart the tone, English 52 I R A D O C A L L S CLEARING AN EMERGENCY ALERT E

(CONVENTIONAL OPERATION ONLY) SENDING AN EMERGENCY REMOTE MONITOR

(CONVENTIONAL OPERATION ONLY) To Clear an Emergency Alert 1 2 Press any button on the radio to cancel the Emergency Alert tone. Press (or activate) an external pushbutton or foot switch. Note: You must press an external switch to clear the visible Emergency Alias and display the next queued Emergency Alias, if present. You must clear all decoded Emergency Alerts before encoding (sending) your own Emergency Alert. As your radio responds to an Emergency Alert, only the Emergency Queue menu is available. To access the Emergency Queue menu:

1 ) to enter Menu Mode. MDC CALL 01 2 The radio displays the list of aliases currently in the Emergency queue, similar to that shown, oldest to newest. 3 z or y to view the next oldest Emergency Remote Monitor packet and to choose the packet to send. 4 Press the PTT to send the packet. 53 English SENDING AN EMERGENCY ALERT E

(CONVENTIONAL OPERATION ONLY) A priority Emergency Alert can be sent to a specific radio or dispatch center by pressing:

A button preprogrammed by your dealer

(see page 27).

The foot switch

A pushbutton accessory Emergency Alerts have priority over all other calls. The E symbol will appear on the display when your radio is in the Emergency Alert state. An Emergency Alert can be programmed to:

Show E and sound a tone or

Show the normal display or

Activate the microphone so that all activity can be transmitted (for a predetermined amount of time). See your dealer for more information. To cancel the Emergency Alert, press and hold down the preprogrammed Emergency button. 54 SENDING A REMOTE MONITOR The Remote Monitor gives the ability to activate the transmit circuit of your radio both silently and normally and key it. The Remote Monitor feature depends on how your radio responds to the Remote Monitor Command. Upon receiving a Remote Monitor Command, the radio:

1. Keys the transmitter. 2. Acknowledges the command 3. Sends the PTT-ID 4. Activates the microphone. Note:

If a remote microphone is attached, it responds. Remote Monitor capability depends on which of two modes are preprogrammed:

Silent Mode When the command is sent in Silent Mode, and the receiving radio keys and transmits for the time set by the Remote Monitor Command, the receiving radio will not generate an indicator of the event.

Non-Silent Mode When the command is sent in Non-Silent Mode, and the receiving radio keys and transmits for the time set by S L L A C O D A R I English I R A D O C A L L S the Remote Monitor Command, the receiv-

ing radio will generate an indicator of the event. The amount of time that the radio remains in receive mode or in transmit mode is set by the Remote Monitor Command and the time settings in the radio. When in this state, touching any button on the radio takes it out of the Remote Monitor mode. See your dealer for more details. SELECTIVE RADIO INHIBIT

(CONVENTIONAL OPERATION ONLY) Your radio is equipped with a security feature that can temporarily render the unit inoperative when an inhibit signal is sent from the base station. This feature is commonly used to disable radios:

In case of theft

When your vehicle is being serviced

For system control reasons Note: When your radio has been disabled by the base station, all controls will be inoperative except for the On/Off button. When the radio is powered up, You see:

Radio Disabled EDITING A RADIO CALL LIST K

(LTR TRUNKED AND CONVENTIONAL OPERATION ONLY) Your radio has a Radio Call list that contains the names and radio IDs of several talkgroups or individuals. The ID numbers in the Radio Call List are programmed by your dealer, and cannot be changed from your radio. However, you can edit the names associated with these IDs. The K symbol appears on the display when you are editing. Note:

The radio cannot receive any calls while you are editing. To Edit a Call List Entry 1 ) to enter menu mode. 2 y or z until Program Lists 55 English

S L L A C O D A R I 3 ) to select Program Lists 4 y or z until RadioCall List 5 ) to select RadioCall List 6 y or z until Edit Entry?

7 ) to select Edit Entry?

8 y or z until you locate the desired entry. 9 ) to select the entry. 10 Use your keypad to edit the entry. 11 ) to save your Edit Entry?

changes. NAME AND CALL TONE TAGGING

(LTR TRUNKED AND CONVENTIONAL OPERATION ONLY) You can program your radio to sound a particular alert tone when a specific user is calling (name tone tagging), or when receiving a particular type of radio call (call tone tagging). Note:

Name and call tone tagging are valid only for selective calls and call alerts. There are seven alert tones to select from.

(see page 87.) To Tag a Specific Users Name 1 ) to enter menu mode. 2 y or z until Name Tone Tag 12 ( to return to Edit Entry?

3 ) to select Name Tone Tag or Hold down ( to exit menu mode. 4 y or z until you see the name you want to tag. 5 ) to confirm the selection. English 56 I R A D O C A L L S 6 y or z until you see and hear the 7 ) to confirm the selection. tone you want to use for this name. 7 ) to confirm the selection, 8 y or z until you see and hear the tone you want to use for this type of call. you see:

Name Tone Set 9 ) to confirm the selection, 8 ( to return to Name Tone Tag you see:

Call Tone Set or Hold down ( to exit menu mode. 10 ( to return to Call Tone Tag or To Tag a Type of Radio Call Hold down ( to exit menu mode. 1 ) to enter menu mode. 2 y or z until Audio/Tones 3 ) to select Audio/Tones 4 y or z until Call Tone Tag 5 ) to select Call Tone Tag 6 y or z until you see the call type you want to tag. 57 English Notes:

S L L A C O D A R I English 58

SCAN Your radio is equipped with the Scan feature, which allows you to search for, lock onto, and monitor voice activity on trunked talkgroups and conventional channels. There are five types of Scan available in your radio:

Auto Group Scan All Group Scan PassPort Primary Auto Scan PassPort Group Scan System Scan The table below summarizes the Scan types available in each zone type. PassPort Primary Auto Scan Pass-

Port Group Scan LTR Auto Group Scan LTR All Group Scan System Scan X X X X X Zone PassPort Trunked LTR Trunked PassPort Primary Auto Scan Pass-

Port Group Scan LTR Auto Group Scan LTR All Group Scan System Scan X Zone Conven-

tional Shaded areas indicate that Scan can be enabled through a programmable button (see page 20) or through your radio menu. TALKBACK When activity is detected during any type of scan, scanning stops and the active talkgroup or channel appears and remains on the display until scanning resumes. Your dealer can program the amount of time you can respond

(or TALKBACK) to the caller before your radio resumes scanning. You must press the PTT button to participate in the call; otherwise, scanning continues to the other talkgroups or channels. S C A N 61 English

N A C S PASSPORT PRIMARY AUTO GROUP SCAN

(PASSPORT TRUNKED OPERATION ONLY) PassPort Primary Auto Group Scan automatically scans the primary (first) talkgroup within the selected PassPort zone. Any time you are positioned on a PassPort talkgroup other than the first one, your radio automatically scans activity on the first talkgroup within that zone. Note:

This feature is enabled AUTOMATICALLY with your radio. It is not enabled through the radio menu or through a prepro-

grammed scan button. PASSPORT GROUP SCAN G

(PASSPORT TRUNKED OPERATION ONLY) PassPort Group Scan scans talkgroups within the selected PassPort trunked zone, as programmed by your dealer. Up to 16 different talkgroups can be programmed into each Scan list, with one Scan list assigned to each position on the Zone Selector. You can edit these Scan lists through your radios menu (see page 66). When PassPort Group Scan is Enabled The G symbol appears on the display. The LED indicator blinks green during PassPort Group Scan operation; it stops blinking when the radio switches to an active talkgroup or channel. Note:

PassPort Group Scan is not available when registered on a non-home site. If you switch to another PassPort zone, LTR, or conventional zone while the radio is scan-

ning, scanning resumes upon return to the PassPort zone where PassPort Group Scan was enabled. If the radio is turned off while scanning, the radio resumes scanning when you turn it back on. If the radio registers on a non-home site, scanning is not enabled until the radio regis-

ters at its home site. English 62

To Start or Stop PassPort Group Scan Operation through a Preprogrammed Button (see page 20) Press the preprogrammed Scan button to start PassPort Group Scan. Press the preprogrammed Scan button again to stop the PassPort Group Scan. or To Start or Stop PassPort Group Scan Operation through the Menu 1 ) to enter menu mode. 2 y or z until Pass Grp Scan 3 ) to select Pass Grp Scan You see the current scan status. 4 y or z until PpGp Scan Off?

or PpGp Scan On?

5 ) to confirm your selection. AUTO GROUP SCAN

(LTR TRUNKED OPERATION ONLY) Auto Group Scan automatically scans talkgroups within an LTR zone as programmed by your dealer. Auto Group Scan can be either non-prioritized or prioritized. Non-prioritized Auto Group Scan automatically scans all talkgroups programmed with Auto Group Scan. Prioritized Auto Group Scan automatically scans the selected talkgroup and all lower 4-numbered talkgroups. For example, if talkgroups 1, 3, and 4 have been programmed by your dealer with Auto Group Scan and talkgroup 4 is selected, the radio automatically scans talkgroups 1, 3, and 4, and skips talkgroup 2. To Start Auto Group Scan Select a talkgroup that has been programmed for Auto Group Scan by your dealer. Note:

You do not need to press a preprogrammed Scan button. S C A N 63 English

N A C S The G symbol appears on the display when non-prioritized Auto Group Scan has been activated. The H symbol appears on the display when prioritized Auto Group Scan has been activated. There is no LED indicator during Auto Group Scan. To Stop Auto Group Scan Select a talkgroup that has not been programmed for Auto Group Scan by your dealer. ALL GROUP SCAN

(LTR TRUNKED OPERATION ONLY) Note:

If you enter menu mode while the radio is scanning, scanning stops. It resumes when you exit menu mode. To Start or Stop All Group Scan Operation through a Preprogrammed Button (see page 20) Press the preprogrammed All Group Scan button once to start All Group Scan. Press the preprogrammed All Group Scan button again to stop All Group Scan. or To Start or Stop All Group Scan Operation Through the Menu 1 ) to enter menu mode. All Group Scan scans all talkgroups within the selected LTR trunked zone. When All Group Scan is enabled:

2 y or z until All Group Scan 3 ) to select All Group Scan The G symbol appears on the display. You see the current scan status. The LED indicator blinks green during All Group Scan operation; it stops blinking when the radio switches to an active talk-

group. 4 y or z until All Group On?

or All Group Off?

5 ) to confirm your selection. English 64

SYSTEM SCAN G

(LTR TRUNKED AND CONVENTIONAL OPERATION ONLY) System Scan scans trunked talkgroups and conventional channels between LTR and conventional zones, as programmed by your dealer. Up to 16 different talkgroups or conventional channels can be programmed into each Scan list. You can edit these lists through your radios menu (see page 66). Do the following:

1 ) to enter menu mode. 2 y or z until System Scan 3 ) to select System Scan You see the current scan status. 4 y or z until Sys Scan On?

When System Scan is Enabled or Sys Scan Off?

The G symbol appears on the display. The LED indicator blinks green during Sys-

tem Scan operation; it stops blinking when the radio switches to an active talkgroup or channel. Note:

If you enter menu mode while the radio is scanning, scanning stops. It resumes when you exit menu mode. To Start or Stop a System Scan Operation Press the preprogrammed Scan button (see page 20) to start or stop scanning, or 5 ) to confirm your selection. Note:

In conventional zones only, if there is activity on a non-priority channel, the radio disconnects the user from the current conversation and automati-

cally switches to an active priority channel. This is indicated with a short alert tone. S C A N 65 English

N A C S DELETING A NUISANCE CHANNEL/

TALKGROUP

(PASSPORT GROUP SCAN OR SYSTEM SCAN OPERATION ONLY) If a talkgroup or channel continually generates unwanted calls (a nuisance channel), use the preprogrammed Scan button to temporarily delete the talkgroup or channel from the Scan list. To Temporarily Delete the Channel/

Talkgroup 1 While the radios receiving activity is on the nuisance channel, press and hold the Scan button until you hear a high-pitched tone (valid key press). 2 Release the Scan button. The nuisance channel has been temporarily deleted from your Scan list. Note:

In PassPort mode, you cannot delete a priority channel/talkgroup (see page 68), or the currently selected talkgroup in a Scan list. Restoring a Channel/Talkgroup Back to the Scan List To restore a previously deleted talkgroup or channel back to the Scan list, restart the scan operation or turn your radio off and on again. Note:

In PassPort mode, the talkgroup can also be restored by scrolling through the list, or switching the current selected talkgroup or zone EDITING A SCAN LIST

(PASSPORT GROUP SCAN OR SYSTEM SCAN OPERATION ONLY) One Scan list is assigned to each of the 16 positions on the Zone Selector. Each Scan list can contain up to 16 talkgroups and/or channels. The same talkgroup or channel can be included in several Scan lists, and the same Scan list can be assigned to several Zone Selector positions. When you edit a Scan list, you can either add, delete, or prioritize talkgroups or channels. English 66 Note:

In PassPort mode, talkgroups cannot be pri-

oritized. Your radio cannot receive any calls while you are editing a Scan list. The K symbol is displayed while you are in edit mode. Note:

In Conventional operation only, even if there is activity on a non-priority channel, your radio automatically switches to an active priority channel and indicates the activity with a short tone. ADDING OR DELETING TALKGROUPS OR CHANNELS IN A SCAN LIST 1 ) to enter menu mode. 2 y or z until Program Lists 3 ) to select Program Lists 4 y or z until Scan List Note: One Scan list per mode of operation is available. 5 ) to select Scan List 6 y or z until Add Entry?

or until Delete Entry?

7 ) to confirm your selection. 8 y or z until you see the talkgroup or channel you want to add or delete. Note: You cannot delete the Primary talk-

group or your selected talkgroup off a Scan List in PassPort mode. 9 ) to confirm your selection. 10 If you added a talkgroup or channel, you see:

or Entry Saved If you delete a talkgroup or channel, you see:

Delete?

) to confirm the deletion, S C A N 67 English you see:

Entry Deleted Priority Channel Scanning Sequence 11 ( to return to Add Entry?

to return to or Delete Entry?

Channel 2

(Priority 1) and Channel 8

(Priority 2) Ch2 Ch1 Ch8 Ch3 Ch2 Ch4 Ch8 Ch1 In Conventional operation only, even if there is activity on a non-priority channel, your radio automatically switches to an active priority channel and indicates the activity with a short tone. N A C S Hold down t to exit menu mode. Note:

PRIORITIZING A TALKGROUP OR CHANNEL IN A SCAN LIST

(SYSTEM SCAN OPERATION ONLY) You may want to check the activity on one or two talkgroups or channels more frequently than others. You can do this by prioritizing them:

Priority Channel Scanning Sequence None specified Ch1 Ch2 Ch3 Ch4 Ch1 Channel 2

(Priority 1) Ch2 Ch1 Ch2 Ch3 Ch2 Ch4 Ch2 Ch1 English 68 Setting Priority Talkgroups or Channels 1 ) to enter menu mode. 11 ) to prioritize that talkgroup or channel. 2 y or z until Program Lists 12 ( to return to Edit Priority?

3 ) to select Program Lists or Hold down ( to exit menu mode. Note:

You cannot reprioritize a priority 1 talk-

group or channel to priority 2. S C A N 4 y or z until Scan List 5 ) to select Scan List 6 y or z until Edit Priority?

7 ) to select Edit Priority?

8 y or z until Priority #1?

or until Priority #2?

You see the current priority talkgroup or channel. 9 ) to select the desired priority level. 10 y or z until you see the talkgroup or channel you want to prioritize. 69 English Notes N A C S English 70 PHONE Your radio allows you to place and receive telephone calls through trunked and conventional systems (depending on phone line availability). Telephone calls through a repeater allow only one person to speak at a time. MAKING A PHONE CALL D THROUGH A TRUNKED SYSTEM Note: The following instructions assume your radio has been programmed as follows by your dealer using CPS (Customer Program-

ming Software). Dial type: Live

Access/Deaccess type: Immediate Auto

Tone Span: Timed - 100 ms tone duration To Initiate a Phone Call Do the following:

1 Select a trunked zone and talkgroup that have been programmed for telephone. 2 ) to enter menu mode. or Press the preprogrammed radio or DTMF microphone Phone button, and skip to step 5. or a. Press and release the Speed Dial button to use the speed dial feature. b. Press the (1 to 9) key corresponding to the number you want to call on the Phone list. Or press 0 if you want to call the last number dialed. c. Press the PTT button. A dial tone sounds. d. Press the PTT button again to send the phone number. or For LTR trunked systems, press and hold the PTT button while dialing a number. 3 y or z until Phone 4 ) to confirm Phone P H O N E 69 English D appears on the display when you are in Phone mode. 5 Press and Release the PTT button. 7 Hold the radio in a vertical position with the microphone 1 to 2 inches (2.5 to 5 cm) away from your mouth. Press the PTT button to talk; release it to listen. If phone access is successful, a dial tone sounds. If phone access is unsuccessful, a low-pitched alternating tone sounds. Disconnect the call (see step 8) and try again. 6 Enter the phone number with the DTMF microphone. The number is automatically sent without pressing the PTT button again. or y or z to select a number from the phone list. XXX-XXX-XXXX Press and release the PTT button again to send the number. 8 To disconnect the phone call:

Press and hold ( to exit Phone. D no longer appears on the display. MAKING A PHONE CALL D THROUGH A CONVENTIONAL SYSTEM To Initiate a Phone Call Press the preprogrammed Phone button, and skip to step 5. or Press the PTT button, and if the Hot keypad feature has been programmed by your dealer, do the following:

1 Select a conventional zone and channel that have been programmed for tele-

phone. E N O H P English 70

2 ) to enter menu mode. 3 y or z until Phone 4 ) to select Phone D appears on the display when you are in Phone Mode. 5

(For conventional operation with auto access only). You hear a series of tones, indicating that an access code is being sent automatically, and see your access code:

or Enter your access code using the DTMF microphone keypad. 6 When you hear a dial tone:

XXX-XXX-XXXX Enter the phone number using the DTMF microphone keypad. or XXX-XXX-XXXX y or z to select a number from the phone list. or (see step 7) 7 a. Press and release the prepro-

grammed Speed Dial button (see step 6) to use the Speed Dial fea-

ture. b. Press the key (1 to 9) corresponding to the number you want to call, or press 0 if you want to call the last number dialed. Note:

To redial the last number dialed (if not using Speed Dial), press and release the PTT button immediately after the access code is sent. The radio sends the last number dialed. or If you entered your access code using the keypad, press z once to access the last number dialed;

then press and release the PTT but-

ton. P H O N E 71 English 8 Press and release the PTT button, if required for your radio. 9 Hold the radio in a vertical position with the microphone 1 to 2 inches (2.5 to 5 cm) away from your mouth. Press the PTT button to talk; release it to listen. 10 To disconnect a phone call, do one of the following:

Enter the deaccess code using the DTMF microphone keypad. or If your radio has the deaccess code programmed, go to step 9. 11 To exit Phone Mode:

Press and hold # to disconnect the call. D disappears from the display. E N O H P English 72 RECEIVING A PHONE CALL D THROUGH A TRUNKED OR CONVENTIONAL SYSTEM To Receive a Phone Call 1 y o r z to select a LTR talkgroup or conventional channel that has been programmed for telephone. or Activate any scan type containing a tele-

phone talkgroup or channel (see page 59). Note:

No PassPort talkgroup or zone selection is needed in PassPort mode.

When a phone call is received, a ring-

ing tone sounds, alerting you to answer the phone call. Note:

The D also appears on the display in PassPort mode. 2 Press the PTT button to answer the phone call. Press the PTT button to talk;

release it to listen. 3 To disconnect the phone call and exit Phone and menu mode:

Press and hold to disconnect the call. Note:

D no longer appears on the display in PassPort mode. MODIFYING THE PHONE LIST K Your radio contains a Phone list that holds up to 25 phone numbers. The Phone list is shared between trunked and conventional Phone operation. You can modify the Phone list in three ways through your radios menu:

Add an entry Delete an entry Edit an existing entry The K symbol appears on the display when you are modifying the phone list. To Add an Entry 1 ) to enter menu mode. 2 y or z until Program Lists 3 ) to select Program Lists 4 y or z until Phone List 5 ) to select Phone List 6 y or z until Add Entry?

7 ) to select, Add Entry?

you see:

Entry Name 8 Use the DTMF microphone keypad to enter the name (see page 23 and page 24). 9 ) to store the name, you see:

Enter Phone #

P H O N E 73 English

10 Use the DTMF microphone keypad to enter the phone number. You can also add a dash

(press w) and a Pause Indicator (hold down # until the # character on the dis-

play changes to a P). 3 ) to select Program Lists 4 y or z until Phone List 5 ) to select Phone List 11 ) to store the phone number. 6 y or z until Delete Entry?

12 y or z until you see the location in the list where you want to store the phone number. 7 ) to select Delete Entry?

8 y or z until you see the entry you want to delete. 13 ) to store the phone number, you see:

Entry Saved 14 ) to return to Add Entry?

Hold down ( to exit menu mode. To Delete an Entry 1 ) to enter menu mode. 2 y or z until Program Lists 9 ) to select the entry, you see:

Delete?

10 ) again to confirm the deletion, you see:

Entry Deleted 11 ( to return to Delete Entry?

or Hold down ( to exit menu mode. E N O H P English 74 To Edit an Entry 1 ) to enter menu mode. 2 y or z until Program Lists 3 ) to select Program Lists 4 y or z until Phone List 5 ) to select Phone List 10 y or z until Edit Name?

(to edit the name), or until

(to edit the phone number), Edit Number?

or until

(to edit the location in the phone list). Edit Location?

6 y or z until Edit Entry?

11 ) to confirm your selection. 7 ) to select Edit Entry?

8 y or z until you see the entry you want to edit. 9 ) to select the entry. 12 Use the DTMF microphone keypad to edit the entry (see page 19), or y or z until you see the location where you want to store the phone num-

ber. 13 ) to store the information. 14 ( to return to Edit Entry?

or Hold down ( to exit menu mode. P H O N E 75 English Notes E N O H P English 76 I V O C E S T O R A G E VOICE STORAGE The CDM1550LS+ radios voice storage feature enables your radio to perform seven types of voice related functions:

Incoming Call Recording Voice Memo Recording Recorded Message Playback Recorded Message Delete Recorded Message Transmission Automatic Message Reply (When Available)

Message Time Stamping There is a total of 120 seconds recording time available for all voice storage activity. Your dealer can divide the 120 seconds into a defined number of equal length time slots. The following table summarizes the slot length options available with the CDM1550LS + radio:

Number of Equal Length Slots Slot Length

(Seconds) 1 2 5 10 20 120 60 24 12 6 When recording calls, keep in mind these time slot guidelines:

As a time slot becomes close to full, you see a timer count down the final 5 seconds. When a time slot is completely full, an alert tone sounds The display shows:

Recording Stops. Msg Slot Full

When all message slots have at least one message stored, an alert tone sounds. 79 English

E G A R O T S E C O V I If a voice storage record function is requested, the dis-

play shows:

Memory Full A confirmation tone sounds, indicating that the radio begins recording. INCOMING CALL RECORDING The CDM1550LS + radio allows you to record incoming calls in either of two ways:

Selective Incomi ng Call Recording

All Incoming Call Recording Note: Only the audio transmissions of your caller is recorded. Selective Incoming Call Recording This feature enables you to record incoming calls selectively, or on a call-by-call basis. To Selectively Record an Incoming Call 1 Press and hold the preprogrammed Record/Playback button (see page 26) while receiving the call. The display shows Recording 2 The radio records the call until the mes-

sage slot is full or until you release the preprogrammed Record/Playback but-

ton. 3 Release the Record/Playback button to stop recording. All Incoming Call Recording This feature enables you to automatically record all incoming trunked and conventional dispatch calls, trunked and conventional telephone interconnect calls, and MDC selective calls. This feature is useful when you need to keep informed of channel activity while away from your radio. Note:

This feature does not work while in scan mode. English 80 To Record All Incoming Calls 1 ) to enter menu mode. 2 y or z until Voice Storage 3 ) to select Voice Storage 4 y or z until Record 5 ) to select Record 6 y or z until All Incoming 7 ) to select All Incoming 8 The display contin-

All Incoming uously flashes, except while a call is being recorded. 9 The display shows while your radio is recording. Recording The radio also records the time stamp and the channel alias to the message slot. 10 Press ( to stop recording. or Go to step 1 again to continue recording in the next available slot. Time Left XX Note: Five seconds before the message slot ends, the radio display shows

(where XX = remaining seconds). The voice storage full alert sounds when the message slot is full, and recording stops. The display shows:

Msg Slot Full I V O C E S T O R A G E 81 English E G A R O T S E C O V I VOICE MEMO RECORDING In addition to recording calls received, the CDM1550LS + radio offers you the ability to record voice memos (or personal reminders) into the radio. The voice memo recording feature is useful for quickly saving phone numbers, names, or any other brief voice information. You can record voice memos using the preprogrammed Record/Playback button

(see page 26) or your radios menu. Important Note:

To record properly, incoming calls cannot be received while a voice memo is being recorded. To Record a Voice Memo using the Preprogrammed Record/Playback Button 2 Without pressing the PTT button, speak clearly into the microphone to record your memo. The radio records your memo until the message slot is full or until you release the preprogrammed Record/

Playback button. 3 Release the Record/Playback button to stop recording. To Record a Voice Memo using the Menu 1 ) to enter menu mode. 2 y or z until Voice Storage 3 ) to select Voice Storage 1 Press and hold the preprogrammed 4 y or z until Record Record/Playback button.

The display shows:

5 ) to select Record Recording 6 y or z until Voice Memo

A confirmation tone sounds, indicating that the radio begins recording. 7 ) to select Recording English 82 8 Without pressing the PTT button, speak clearly into the microphone to record your memo. The radio records your memo until the message slot is full or until you press (. Note:

To stop recording at any time, press

(. 9 Press ( to stop recording. or Repeat steps 7 and 8 to store additional messages. RECORDED MESSAGE PLAYBACK The CDM1550LS + allows you to list, select, and Playback previously recorded incoming call or voice memo messages. You can play back a message by using the preprogrammed Record/Playback button (see page 26) or your radios menu. Note:

Recorded message Playback cannot be initiated while your radio is receiving. Also, you dont receive any incoming calls while you play back messages. Playing Msg XXX To Playback a Message using the Preprogrammed Record/Playback Button 1 Press and release the preprogrammed Record/Playback button.

The first mes-

Playing Msg XXX sage plays, and the display shows (XXX = the mes-

sage number) I V O C E S T O R A G E 2 To advance to the next message at any time during Play back, press and release the Record/Playback button again. 3 To exit/cancel Playback mode:

Press and release the preprogrammed Playback Exit button (see page 26). or Press ( to stop Play Back. 83 English E G A R O T S E C O V I To Playback a Message using the Menu 1 ) to enter menu mode. 2 y or z until Voice Storage 3 ) to select Voice Storage 4 y or z until Playback 5 ) to select Playback 6 y or z until 001 12:00A 005 7 ) to select 001 12:00A 005 RECORDED MESSAGE DELETE The CDM1550LS + radio allows you to delete previously recorded incoming call or voice memo messages. You can delete a message using either the preprogrammed Delete Playback button (see page 26) or your radios menu. Note: Messages must be deleted one at a time. To Delete a Message using the Preprogrammed Delete Playback Button

(see page 26) 1 Press and release the preprogrammed Record/Playback button. 2 y or z to select the desired mes-

Message #

Time Stamp Duration (in seconds) sage. 8 y or z to select the desired mes-

sage. 9 Press ) to play the selected message. 10 y or z anytime during playback to advance to the next message. 3 Press and hold the preprogrammed Delete Playback button to delete current message. 4 ( to stop deleting messages. English 84 To Delete a Message using the Menu 1 ) to enter menu mode. 2 y or z until Voice Storage 3 ) to select Voice Storage 4 y or z until Delete 5 ) to select Delete 6 y or z to select the desired mes-

sage. 7 Press ) to delete the selected mes-

sage. 8 y or z to select the another mes-

sage to be deleted, then go to step 7. or Press ( to stop deleting messages. RECORDED MESSAGE TRANSMISSION This feature allows you to transmit a recorded message to another radio user. To Transmit a Recorded Message 1 Press and hold the PTT button to initiate the message transmission. 2 While holding down the PTT button, press the preprogrammed Record/Play-

back button to select and play back the desired recorded call or memo. 3 When finished transmitting your mes-

sage, press the Record/Playback but-

ton again to stop transmitting. I V O C E S T O R A G E 85 English E G A R O T S E C O V I ANSWER MODE The Answer Mode feature allows radio callers to leave recorded audio messages on your radio. Note:

This feature is available via the radios menu and/or the radio or the DTMF micro-

phone programmable button. To Enable the Answer Mode Feature 1 ) to enter menu mode. 3 y or z until Alternate Msg?

4 ) to select Greeting Msg?

The LCD shows Recording 5 Without pressing the PTT button, speak clearly into the microphone to record your memo. The radio records your greeting until the message slot is full or until you press (. 2 y or z until Voice Storage 6 To exit or cancel recording, press (. With this feature enabled, the recorded message is automatically transmitted whenever your radio receives a call. 3 ) to select Voice Storage Voice Storage 4 y or z until Ans Mode On?

5 ) to select Ans Mode On To Record a Message 1 y or z until Record Msg 2 ) to select Greeting Msg?

English 86 To Disable the Answer Mode Feature 1 ) to enter menu mode. 2 y or z until Voice Storage 3 ) to select Voice Storage 4 y or z until Ans Mode Off?

5 ) to select Ans Mode Off I V O C E S T O R A G E 87 English Notes E G A R O T S E C O V I English 88 AUDIO/TONE SETTINGS You can customize the audio and tone feature settings on your radio by:

1 ) to enter menu mode. 2 y or z until Audio/Tones 3 ) to select Audio/Tones 4 y or z until you see the feature you want to change (see the table on the next page). 5 ) to select the feature. You see the features current setting. 6 y or z for available settings. (For Name and Call Tone Tagging, see page 56.) 7 ) to set the desired setting. S E T T N G S I I A U D O T O N E

87 English Feature Alert Vol Lvl Audio/Tone Settings What it Does Makes the volume level of the audio and alert tones inde-

pendent. If turned on, it makes the alert tones follow the settings in the CPS; if turned off, the alert tones follow the setting of the volume knob. Tone Disable Turns all alert and audio tones on or off. Settings Ind Alert Off Ind Alert On Tones On Tones Off Name and Call Tone Tagging Call Tone Tag Escalert Companding Assigns a specific ring tone when receiving a call from a specific user (see page 56 for details). Standard Alert #1 #7 Assigns a specific tone when receiving a specific type of radio call (see page 56 for details). Standard Alert #1 #7 Increases the volume of the alarm tones when a radio call is not answered. Provides the same audio quality for 12.5kHz and for 25kHz channels. Escalert On Escalert Off Compand On Compand Off LTR trunking operation only.

E N O T O D U A I I S G N T T E S English 88 UTILITIES You can customize some of your radios feature by:

1 ) to enter menu mode. 2 y or z until Utilities 3 ) to select Utilities 4 y or z until you see the feature you want to change (see table on the next page). 5 ) to select the feature. You see the features current setting. 6 y or z for available settings. 7 ) to select the desired setting. I I U T L T E S I 91 English Feature Power Level Utilities Features What it Does Settings Changes the power level of the radio to high, low (see page 93). Power High Power Low Clock Sets the time, or turns the clock on or off (see page 94). Reminder Alarm Sets the alarm, or turns it on or off (see page 94). Language Selection Selects the language to be shown on your radios dis-

plays. Software Ver #

In LTR trunked and conventional operation, displays the radios software version number when you press ). In PassPort operation, displays the PassPort software version number when you press ). Note: The LTR and conventional software version number may be different than the PassPort software version number. Clock On Clock Off Set Time Alarm On Alarm Off Set Time English Spanish Portuguese French I S E T L T U I I Conventional Operation only. LTR Trunked Operation only. English 92 SETTING THE POWER LEVEL B Each channel in your radio has a predefined transmit power level that can be changed. Do the following:

1 ) to enter menu mode. 2 y or z until Utilities 3 ) to select Utilities 4 y or z until Power Level 5 ) to select Power Level The display shows the current power level. 6 y or z until Power High?

or until Power Low?

7 ) to confirm the selection. High power (S) allows you to reach a radio that is farther away. Low power (R) conserves the batterys charge. Note:

Be aware that a message received from a nearby radio might change your radios power level to low. This may cause radios that are farther away not to receive your transmis-

sions. In PassPort mode, the power level is predefined radio wide. To set the power level:

Press the preprogrammed Power Level button

(see page 25) to toggle between low and high, or I I U T L T E S I 93 English

SETTING THE CLOCK/ALARM To Set the Clock/Alarm 9 v or w to move to the previous or next setting. 1 ) to enter menu mode. 10 ) to save your changes. 2 y or z until Utilities 11 ( to return to Utilities 3 ) to select Set time?

or to return to Reminder Alarm 4 y or z until Clock or until Reminder Alarm or or Clock 5 ) to confirm your selection. Hold down ( to exit menu mode. 6 y or z until Set time?

7 ) to select Set time?

8 When a setting is blinking, you can change it with y or z. Hour (AM or PM) 3:05 PM Minutes

(AM/PM or 24 hr) Note:

You cannot select 24 hr for Reminder Alarm I S E T L T U I I English 94 DISPLAYING THE TIME To Display the Time 1 ) to enter menu mode. 2 y or z until Utilities 3 ) to select Utilities 4 y or z until Clock 5 ) to confirm your selection. SELECTING THE DISPLAY LANGUAGE

(LTR TRUNKED AND CONVENTIONAL OPERATION ONLY) To Select the Display Language 1 ) to enter menu mode. 2 y or z until Utilities 3 ) to select Utilities 6 y or z until Display Clock?

4 y or z until Language Select 7 ) to select Display Clock?

5 ) to confirm your selection. The radio displays the time for a pre-

programmed dura-

tion. 6 y or z until the desired language is displayed. 7 ) to confirm your selection. 8 ( to exit the menu. 8 ( to exit the menu. I I U T L T E S I 95 English Notes I S E T L T U I I English 96 12_Warranty.fm Page 95 Thursday, April 4, 2002 4:39 PM W A R R A N T Y WARRANTY LIMITED WARRANTY MOTOROLA COMMUNICATION PRODUCTS I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:

MOTOROLA INC. (MOTOROLA) warrants the MOTOROLA manufactured Communication Products listed below (Product) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:

CDM1550LS + Mobile Units Two (2) Years Product Accessories One (1) Year Motorola, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA. This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product. MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. 95 English 12_Warranty.fm Page 96 Thursday, April 4, 2002 4:39 PM Y T N A R R A W II. GENERAL PROVISIONS:

This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLAs option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. III. STATE LAW RIGHTS:

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. IV. HOW TO GET WARRANTY SERVICE:

You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by Motorola through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call Motorola at 1-800-927-

2744 US/Canada. English 96 12_Warranty.fm Page 97 Thursday, April 4, 2002 4:39 PM W A R R A N T Y V. WHAT THIS WARRANTY DOES NOT COVER:

A) Defects or damage resulting from use of the Product in other than its normal and customary manner. B) Defects or damage from misuse, accident, water, or neglect. C) Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. D) Breakage or damage to antennas unless caused directly by defects in material workmanship. E) A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-Motorola supplied equipment) which adversely affect performance of the Product or interfere with Motorola's normal warranty inspection and testing of the Product to verify any warranty claim. F) Product which has had the serial number removed or made illegible. G) Rechargeable batteries if:

1) any of the seals on the battery enclosure of cells are broken or show evidence of tampering. 2) the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified. H) Freight costs to the repair depot. A Product which, due to illegal or I) unauthorized alteration of the software/

firmware in the Product, does not function in accordance with MOTOROLAs published specifications or the FCC type acceptance labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA. J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. K) Normal and customary wear and tear. VI. PATENT AND SOFTWARE PROVISIONS:

MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:

97 English 12_Warranty.fm Page 98 Thursday, April 4, 2002 4:39 PM A) B) that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;

that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and C) should the Product or parts become, or in MOTOROLAs opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA. MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such Motorola software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights. VII. GOVERNING LAW:

This Warranty is governed by the laws of the State of Illinois, USA. Y T N A R R A W English 98 13_Accessory.fm Page 99 Thursday, April 4, 2002 4:40 PM ACCESSORIES Motorola offers a number of accessories to enhance the productivity of your two-way radio. Many of the available accessories are listed below. For a complete list, see your Motorola dealer. MICROPHONES AARMN4025_ Standard Compact Microphone AARMN4026_ Enhanced DTMF Keypad Microphone AARMN4038_ Heavy Duty Microphone AAREX4617_ Telephone Style Handset with Hang-Up Cup HLN9073_R Microphone Hang-Up Clip (all microphones) HANDSFREE KITS AARMN4027_ Visor Mounted Microphone RLN4856_ RLN4857_ RLN4858_ Footswitch PTT Pushbutton PTT Gooseneck PTT EXCHANGEABLE BUTTON KITS Note: Other individual exchangeable buttons are available through AAD. Please see Basic Service Manual for button numbers. RLN4831_ RLN5324_ Standard Button Kit: MON, SCAN, CALL, HOME, PHONE Standard Button Kit: MON, SCAN, CALL, HOME, PHONE, ROAM, SITE MOUNTING KITS GLN7324_R Standard Low Profile Bracket (VHF/UHF) High Profile Mounting Bracket (VHF/UHF) GLN7317_ Key Lock Mounting Bracket (VHF/UHF) RLN4779_ Direct in Dashboard Mounting Kit (VHF/

RLN4781_ UHF) Removable Slide Mount Tray Package

(VHF/UHF - A maximum of two external accessory wires can be attached to the slide tray) HLN8097_ A C C E S S O R E S I 99 English 13_Accessory.fm Page 100 Thursday, April 4, 2002 4:40 PM REMOTE MOUNTS RLN4802_ RKN4077_ RKN4078_ RKN4079_ Remote Mount Kit - CDM1250 and CDM1550 models (requires HKN4192 power cable) Remote Mount Cable, 3 meter length Remote Mount Cable, 5 meter length Remote Mount Cable, 7 meter length EXTERNAL SPEAKERS HLN9457_R Hardware Kit for use with the Expanded Accessory Connector (includes 16 connector pins, (five) 8 wires with pins attached and an extra housing) ANTENNAS HKAD4001_ HAF4012_ 220 MHz, 1/4-Wave Roof Mount Mini-U 746-794 MHz, 1/4-Wave Roof Mount RSN4001_ HSN8145_ 13 Watt External Loudspeaker 7.5 Watt External Speaker - for Receiver Audio SERVICE AIDS AND PROGRAMMING EQUIPMENT INSTALLATION AND ALARM KITS H5177 HKN4137_ HKN4192_ Standard 12V 10 Power Cable to Battery

(VHF/UHF) 12V 20 Ft. Power Cable to Battery (VHF/

UHF) External Alarm Relay and Cable Emergency Footswitch Ignition Switch Cable GKN6272_ RLN4836_ HKN9327_ HKN9557_R PL259/Mini-U Antenna Adapter - 8 Cable Portable/Mobile Programming Software

(CPS) 3 Year Subscription Package -

Includes CPS CD ROM Software:

HVN9025 for the HT/EX500/CDM/MTX.LS Series and HVN9067 for MTX Series Privacy Plus. Includes HT/MTX Series Programming/Test Cable (AARKN4074). Also is compatible with RLN4460 used for radio testing. (HVN9025 is compatible with Windows 95/98/2000/Millennium (ME)/

Windows NT. HVN9067 is compatible with Windows 95/98/Windows NT). Note:

Software requires a license agreement and is not intended for resale. I S E R O S S E C C A English 100 13_Accessory.fm Page 101 Thursday, April 4, 2002 4:40 PM AARKN4081_ Programming Cable with Internal RIB

(direct connection from computer to radio microphone connector) AARKN4083_ Programming Cable (allows radio programming via rear accessory connector) 3080070N01 Programming Cable (connection from RIB 3080369B72 to radio) 9 Pin PC to Radio Interface Box Cable

(IBM AT or compatible) Test Box for Portables and Mobiles Radio Interface Box (RIB) RLN4460_ RLN4008_ 0180357A57 Wall Mounted Power Supply, 120V - used RLN4853_ with RLN4008 10 to 20 Pin Adapter MANUALS 6864110R14 CDM1550 LS+ 220/700 MHz Detailed Service Manual 6864110R16 CDM1550 LS+ 200/700 MHz Basic Service Manual 6881092C58 Installation Manual (English) CONTROL STATION KITS HMN3000_ GLN7326_ GLN7318_ HKN9088_ Desk Microphone (Black) Desktop Tray with Speaker Desktop Tray without Speaker Mobile Mini-U Antenna Adapter - 8 Ft. Cable HPN4002_R Power Supply and Cable (1-25 Watt Models) HPN4001_R Power Supply and Cable (25-60 Watt Models) MOBILE DATA UNITS SECTION Terminals:

RDN7365_ RDN7366_ Mobile Status Terminal - Mobile messaging device equipped with a data modem. This will allow a mobile user to report status messaging back to the dispatcher by activating one of the status keys. Mobile Status Terminal with GPS - Mobile status terminal equipped with an Automatic Vehicle Location (AVL) device compatible with Global Positioning System

(GPS). A C C E S S O R E S I 101 English 13_Accessory.fm Page 102 Thursday, April 4, 2002 4:40 PM I S E R O S S E C C A RDN7367_ RDN7368_ RDN7369_ RDN7738_ Mobile Display Terminal with GPS - Mobile display terminal equipped with an Automatic Vehicle Location (AVL) device compatible with Global Positioning system

(GPS). Mobile Display Terminal - Mobile messaging device equipped with a data modem. This unit features a 4x40 backlit LCD display and the keypad allows users to send information to the dispatcher in response to base instructions. Standalone Modem/GPS - Cost efficient Automatic Vehicle Location (AVL) device compatible with Global Positioning System

(GPS). Serial Breakout Unit (used in multiple applications that allow up to eight base modems to be connected). Radio Interface Cables: One radio interface cable is required with purchase of each hardware device RDN7370_ RDN7376_ RDN7739_ 3 Ft. Interface Cable with 16 Pin Connector 15 Ft. Interface Cable with 16 Pin Connector 3 Ft. Flying Cable (same as regular interface cable, but omits connectors). RDN7740_ 15 Ft. Flying Cable (same as regular interface cable, but omits connectors). Peripherals:

RDN7371_ RDN7373_ Credit Card Reader - Card reader is used to perform automatic online credit card authorization transaction. Used with RDN7379 (credit card software). Mobile Printer - The mobile printer provides users with a hard copy of the information transmitted from the base dispatch location. Global Positioning System (GPS) Antennas:

Antenna is required with purchase of any GPS unit RDN7372_ RDN7375_ Fixed Mount GPS Active Antenna Magnetic Mount GPS Active Antenna Software:

RDN7374_ RDN7377_ Programming Software - Used for mobile data units. Regional Map Software - Will allow up to 10 selected US counties. English 102 13_Accessory.fm Page 103 Thursday, April 4, 2002 4:40 PM RDN7378_ RDN7379_ AVL Messaging Status Software -

Mapping software that provides the user with Automatic Vehicle Location to track vehicles along with message dispatch and status tracking capability. Credit Card Software - Used with RDN7371 (credit card reader). Miscellaneous:

RDN7364_ RDN7380_ Radio Channel Card - A radio channel controller and modem that interface with the base radio. Required with every radio channel or wireless circuit used within the system. Mobile Programming Hardware PUBLIC ADDRESS RLN5288_ HKN9323_ HKN9324_ Public Address Kit (includes interface cable 8 Ft. Public Address Speaker Cable 15 Ft. Public Address Speaker Cable (one cable per speaker) HSN1000_R 6 Watt Amplified External Speaker RETROFIT KIT 6686119B01 Dismantling Tool A C C E S S O R E S I 103 English 13_Accessory.fm Page 104 Thursday, April 4, 2002 4:40 PM Notes:

I S E R O S S E C C A English 104 Selecting a Trunked Zone and Talkgroup 1. v or w to select desired trunked zone. 2. y or z until you see desired preprogrammed talkgroup on the display. Sending a Trunked Call 1. Press PTT button. If trunked system access was successful Red LED = steady;

if unsuccessful LED = flashing; red-low pitched tone sounds. 2. Speak clearly into microphone. Release PTT button to listen. Initial PassPort System Registration PASSPORT TLKGRP ALIAS SEARCHING REG SITE XXX TLKGRP ALIAS Upon power up, PassPort alias appears on the LCD. On/Off/Volume Control Knob The selected talkgroup alias appears on the LCD. May appear if a PassPort site cannot be quickly located. Appears indicating successful PassPort registration

(XXX = PassPort site on which you are registered). Selected talkgroup alias appears and remains on the display upon successful registration. CDM1550LS+ Quick Reference Card Record the functions for your radios programmable buttons in the table provided below. For further information, see pages 24 and 25 in this User Guide. Red/Yellow/Green LED Indicators LCD Screen Talkgroup/Channel Selector/

Menu Navigation Buttons

(Up/Down) Menu Exit/Escape Button Menu Enter/Select Button Programmable Button 3 (P3)

(Interchangeable) Selecting a Conventional Zone and Channel 1. v or w to select desired conventional zone. 2. y or z until you see desired conventional channel on the display. Sending a Conventional Call Press PTT button and speak clearly into microphone. LED = steady while call is being sent. Release PTT button to listen. Receiving a Trunked or Conventional Call

v or w, then y or z to desired talkgroup or channel. Make sure PTT button is released. When a call is received, the LED flashes. Making a Selective Call (LTR Trunked and Conventional Operation only) 1. From Selective Call menu, select or enter desired radio ID number. 2. Press PTT button to send the call. The radio sounds a continuous tone. 3. Press PTT button and talk; release PTT button to listen. Receiving a Selective Call (LTR Trunked and Conventional Operation only)

When a Selective Call is received, the radio displays F symbol and name or ID of calling radio; the yellow LED flashes. Press PTT button to answer. Microphone Jack Programmable Button 1 (P1)

(Interchangeable) Programmable Button 2 (P2)

(Interchangeable) Zone Selector/

Editing Buttons

(Left/Right) Programmable Button 4 (P4)

(Interchangeable) Button Feature Short Press Long Press Hold Down Page

Menu Navigation Chart

(Refer to Menu Navigation guidelines lower, left-hand corner of this page)

* Available in PassPort trunked zones only Available in LTR trunked zones only Available in conventional zones only

) y z Radio Call Rptr/

Talkarnd

(p. 34) y z y z repeater mode/

talkarnd mode

(LTR) All Group Scan(p. 64) y z on/off PP Group Scan*

(p. 62) y z on/off Voice Storage y z LTR /Con System Scan y z on/off Program Lists y z Selective Call Call Alert Radio Check select/enter ID select/enter ID select/enter ID Menu Navigation

) to enter menu mode y or z to scroll through the list Delete

(p. 84) Playback

(p. 83) Record

(page 80) Phone List

(p. 75) add/delete/

edit entry all incoming voice memo RadioCall List

(p. 57) edit entry Scan List

(p. 66) add/delete entry edit priority

( and )

) to select menu item y or z to scroll through sub-list

( to return to previous menu level

) to select sub-menu item or Hold down ( to exit menu mode Phone

(p. 71) Audio/Tones

(p. 89) Utilities

(p. 91) y z y z Alert Vol Lvl on/off Tone Disable on/off Call Tone Tag standard/alert

#1 - #7 Escalert on/off Companding on/off Power Level high/low/

auto ( and ) Clock on/off/set time Reminder Alarm on/off/set time Language Selection English/French/

Portuguese/

Spanish Software Ver#

6864110R13-O_cvr.qxd 2/21/02 12:39 PM Page 1 Motorola, The Stylized M logo, Intelligence Everywhere, Professional Radio - As Dedicated As You Are, CDM Series, CDM1550LS+, and Call Alert are trademarks of Motorola, Inc. LTR is a mark of E.F. Johnson Company. PassPort is a mark of Trident Micro Systems. 2002 Motorola, Inc. All rights reserved. Printed in U.S.A.

*6864110R13-O*

6864110R13-O CDM1550LS++ User Guide Professional Radio - As Dedicated As You Are