all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Exhibit 8A User Manual | Users Manual | 2.40 MiB | April 09 2007 | |||
1 |
|
Exhibit 8B User Manual | Users Manual | 3.44 MiB | April 09 2007 | |||
1 | ID Label/Location Info | April 09 2007 | ||||||
1 | RF Exposure Info | April 09 2007 | ||||||
1 | RF Exposure Info | April 09 2007 | ||||||
1 | Cover Letter(s) | April 09 2007 | ||||||
1 | Cover Letter(s) | April 09 2007 | ||||||
1 | Attestation Statements | April 09 2007 | ||||||
1 | Test Report | April 09 2007 | ||||||
1 | Test Report | April 09 2007 | ||||||
1 | Internal Photos | April 09 2007 / September 12 2007 | ||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | / September 12 2007 | ||||||
1 | ID Label/Location Info | |||||||
1 | Cover Letter(s) |
1 | Exhibit 8B User Manual | Users Manual | 3.44 MiB | April 09 2007 |
zTitle Page XPR 4300/4350/4500/4550 Mobile Radio Installation Manual Motorola, Inc. 8000 West Sunrise Boulevard Fort Lauderdale, Florida 33322 i 6816812H01 Foreword This manual covers the XPR 4300/4350/4500/4550 digital mobile radios. It includes all the information necessary to maintain peak product performance and maximum working time, using levels 1 and 2 maintenance procedures. This level of service goes down to the board replacement level and is typical of some local service centers, self-maintained customers, and distributors. For details on radio operation or component-level troubleshooting, refer to the applicable manuals available separately. A list of related publications is provided in the section Related Publications, on page vi. Product Safety and RF Exposure Compliance See Installation Requirements for Compliance with Radio Frequency (RF) Energy Exposure Safety Standards, on page iii. Manual Revisions Changes which occur after this manual is printed are described in FMRs (Florida Manual Revisions). These FMRs provide complete replacement pages for all added, changed, and deleted items. To obtain FMRs, go to https://businessonline.motorola.com. Parts Ordering See Appendix A: Replacement Parts Ordering for information on how to obtain replacement parts. For part numbers, refer to the XPR 4300/4350/4500/4550 Digital Mobile Radio Basic Service Manual (Motorola publication part number 6816816H01). Computer Software Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. Document Copyrights No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights nor the rights of others. Trademarks MOTOROLA, the Stylized M logo, FLASHport are registered in the US Patent & Trademark Office. All other product or service names are the property of their respective owners. Motorola, Inc. 2006. ii Installation Requirements for Compliance with Radio Frequency (RF) Energy Exposure Safety Standards ATTENTION!
This radio is intended for use in occupational/controlled conditions, where users have full knowledge of their exposure and can exercise control over their exposure to meet FCC limits. This radio device is NOT authorized for general population, consumer, or any other use. To ensure compliance to RF Energy Safety Standards:
Install only Motorola approved antennas and accessories Be sure that antenna installation is per Antenna Installation, on page 2-8 of this manual Be sure that Product Safety and RF Safety Booklet enclosed with this radio is available to the end user upon completion of the installation of this radio Before using this product, the operator must be familiar with the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with each radio (Motorola Publication part number 68P81095C99) to ensure compliance with Radio Frequency (RF) energy exposure limits. For a list of Motorola-approved antennas and other accessories, visit the following web site which lists approved accessories for your radio model: http://www.motorola.com/governmentandenterprise. iii This Page Intentionally Left Blank iv Table of Contents Table of Contents v Foreword.........................................................................................................ii Product Safety and RF Exposure Compliance............................................................................................ii Manual Revisions ........................................................................................................................................ii Parts Ordering .............................................................................................................................................ii Computer Software Copyrights ...................................................................................................................ii Document Copyrights..................................................................................................................................ii Disclaimer....................................................................................................................................................ii Trademarks .................................................................................................................................................ii Installation Requirements for Compliance with Radio Frequency (RF) Energy Exposure Safety Standards......................iii Mobile Radio Model Numbering Scheme..................................................viii Commercial Warranty ...................................................................................ix Limited Warranty ........................................................................................................................................ix MOTOROLA COMMUNICATION PRODUCTS................................................................................ix I. What This Warranty Covers And For How Long .....................................................................ix II. General Provisions.................................................................................................................ix III. State Law Rights ....................................................................................................................x IV. How To Get Warranty Service ...............................................................................................x V. What This Warranty Does Not Cover......................................................................................x VI. Patent And Software Provisions ...........................................................................................xi VII. Governing Law.....................................................................................................................xi Chapter 1 Introduction ......................................................................... 1-1 1.1 Mobile Radio Description............................................................................................................... 1-1 1.1.1 Dimensions ....................................................................................................................... 1-1 1.2.1 Dash Mount Configuration ................................................................................................ 1-2 1.3 Base/Control Stations .................................................................................................................... 1-2 1.4 Tools Required for XPR 4300/4350/4500/4550 Installations......................................................... 1-3 Chapter 2 Standard Configurations.................................................... 2-1 2.2.2 2.1 Planning the Installation................................................................................................................. 2-1 2.2 Radio Mounting.............................................................................................................................. 2-4 Locking Kit (Optional) ....................................................................................................... 2-6 2.2.2.1 All Radios................................................................................................................. 2-6 2.3 Power Cable .................................................................................................................................. 2-6 2.4 Ignition Sense Cable...................................................................................................................... 2-8 2.5 Antenna Installation ....................................................................................................................... 2-8 2.5.1 Selecting an Antenna Site/Location on a Metal Body Vehicle .......................................... 2-8 2.5.2 Mini-UHF Connection ....................................................................................................... 2-9 2.6 Speaker ...................................................................................................................................... 2-10 2.7 Microphone Hang-Up Clip ........................................................................................................... 2-12 6816812H01 March 23, 2006 vi Table of Contents 2.7.1 Standard Hang-Up Clip................................................................................................... 2-12 2.7.2 Handheld Hang-Up Box.................................................................................................. 2-12 2.8 Completing the Installation .......................................................................................................... 2-12 Chapter 3 Options and Accessories Installation ............................... 3-1 3.1 Emergency Pushbutton, Footswitch, Horn Relay, and Light Relay Installation............................. 3-1 Emergency Pushbutton or Footswitch Installation............................................................ 3-1 3.1.1 3.1.2 Horn (External Alarm) Relay Installation........................................................................... 3-1 3.1.3 Lights (External Alarm) Relay Installation......................................................................... 3-1 3.2 Dash-Mount Accessory Installation ............................................................................................... 3-1 3.2.1 MDC Emergency Pushbutton or Footswitch Installation................................................... 3-2 3.2.2 Horn and Lights (External Alarm) Relay ........................................................................... 3-3 Appendix A Replacement Parts Ordering..............................................A-1 A.1 Basic Ordering Information............................................................................................................A-1 A.2 Motorola Online .............................................................................................................................A-1 A.3 Mail Orders ....................................................................................................................................A-1 A.5 Fax Orders.....................................................................................................................................A-2 A.6 Parts Identification .........................................................................................................................A-2 A.7 Product Customer Service.............................................................................................................A-2 Glossary .........................................................................................Glossary-1 Index .....................................................................................................Index-1 Related Publications XPR 4300/4350/4500/4550 Digital Mobile Radio Basic Service Manual .................................... 6816816H01 March 23, 2006 6816812H01 List of Figures List of Figures vii Figure 1-1. Front View of Dash Mount Transceiver Trunnion.................................................................. 1-1 Figure 1-2. Side View of Dash Mount Transceiver Trunnion................................................................... 1-1 Figure 1-3. Dash Mount Configuration .................................................................................................... 1-2 Figure 1-4. Remote Mount Configuration, with 110W transceiver........................................................... 1-2 Figure 2-1. Mounting Flexibility in Middle Console.................................................................................. 2-1 Figure 2-2. On Top or Under Dash Mounting .......................................................................................... 2-1 Figure 2-3. Radio Installation (Dash Mount) with Transceiver................................................................. 2-2 Figure 2-4. Pin Configuration .................................................................................................................. 2-3 Figure 2-5. Trunnion Orientation ............................................................................................................. 2-4 Figure 2-6. Transmission Hump Trunnion Mounting ............................................................................... 2-5 Figure 2-7. Below Dash Trunnion Mounting............................................................................................ 2-5 Figure 2-8. Locking Kit (Optional) 110W Radios ..................................................................................... 2-6 Figure 2-9. Cabling Interconnect Diagram for Dash Mount..................................................................... 2-7 Figure 2-30. Mini-UHF Connection (as shown on mid-power) .................................................................. 2-9 Figure 2-31. Mini-UHF Connector Tool (as shown on mid-power) .......................................................... 2-10 Figure 2-32. Speaker Mounting............................................................................................................... 2-11 Figure 3-1. VIP Connector Detail ............................................................................................................ 3-1 Figure 3-2. Emergency Switch Wiring Diagram ...................................................................................... 3-2 Figure 3-3. Horn/Light Wiring Diagram.................................................................................................... 3-3 List of Tables Table 3-1. Rear Accessory Jack Pin Functions ..................................................................................... 3-4 6816812H01 March 23, 2006 viii Mobile Radio Model Numbering Scheme Mobile Radio Model Numbering Scheme 2 7 Q P H 2 3 6 4 5 Typical Model Number:
Position:
AZ M 1 Position 1 - Type of Unit M = Mobile Positions 2 & 3 - Model Series Model - XPR Series Position 4 - Frequency Band J
Q
T
136 to 174MHz 403 to 470MHz 450 to 527MHz Position 5 - Power Level N
P
Q
1-25 Watts 25-40 Watt 25-45 Watt Position 6 - Physical Packages
C
H
N
R Low Tier Mid Tier High Tier Repeater Position 7 - Channel Spacing 9 = Variable/Programmable 9 7 L 8 A 9 1 10 A 11 N 12 Position 12 -
Unique Model Variations N = North America
(Standard Package) Position 11 - Version Version Letter Position 10 - Feature Level 1 = Mini-U 2 = BNC 3 = Wall Mount 5 = Desktop 7 = Rack Mount Position 9 - Primary System Type A =
Conventional Position 8 - Primary Operation
J
L Without GPS With GPS March 23, 2006 6816812H01 Commercial Warranty Commercial Warranty ix Limited Warranty MOTOROLA COMMUNICATION PRODUCTS I. What This Warranty Covers And For How Long MOTOROLA INC. (MOTOROLA) warrants the MOTOROLA manufactured Communication Products listed below (Product) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:
XPR 4300/4350/4500/4550 Mobile Radio Product Accessories Two (2) Year One (1) Year Motorola, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA. This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product. MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. II. General Provisions This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA's option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. 6816812H01 March 23, 2006 x III. State Law Rights Commercial Warranty SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. IV. How To Get Warranty Service You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by Motorola through one of its authorized warranty service locations. If you first contact the company which sold you the Product, it can facilitate your obtaining warranty service. You can also call Motorola at 1-888-567-7347 US/Canada. V. What This Warranty Does Not Cover A. Defects or damage resulting from use of the Product in other than its normal and customary manner. B. Defects or damage from misuse, accident, water, or neglect. C. Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. D. Breakage or damage to antennas unless caused directly by defects in material workmanship. E. A Product subjected to unauthorized Product modifications, disassemblies or repairs (includ-
ing, without limitation, the addition to the Product of non-Motorola supplied equipment) which adversely affect performance of the Product or interfere with Motorola's normal warranty inspection and testing of the Product to verify any warranty claim. F. Product which has had the serial number removed or made illegible. G. Rechargeable batteries if:
- any of the seals on the battery enclosure of cells are broken or show evidence of tamper-
ing.
- the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified. H. Freight costs to the repair depot. I. A Product which, due to illegal or unauthorized alteration of the software/firmware in the Prod-
uct, does not function in accordance with MOTOROLAs published specifications or the FCC type acceptance labeling in effect for the Product at the time the Product was initially distrib-
uted from MOTOROLA. J. Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. K. Normal and customary wear and tear. March 23, 2006 6816812H01 Commercial Warranty VI. Patent And Software Provisions xi MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:
A. B. that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;
that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and C. should the Product or parts become, or in MOTOROLA's opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to con-
tinue using the Product or parts or to replace or modify the same so that it becomes nonin-
fringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA. MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such Motorola software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights. VII. Governing Law This Warranty is governed by the laws of the State of Illinois, USA. 6816812H01 March 23, 2006 xii Commercial Warranty Notes March 23, 2006 6816812H01 Chapter 1 Introduction This manual covers the installation procedures for XPR 4300/4350/4500/4550 mobile and motorcycle radios with O5 control heads and accessories required to complete the radio system. The radio system consists of a control head, radio, antenna, microphone, speaker, cabling, and accessories. 1.1 Mobile Radio Description 1.1.1 Dimensions Figure 1-1 and Figure 1-2 show the basic dimensions of the dash mount transceiver trunnion XPR 4300/4350/4500/4550. The transceiver portion of a remote mount is sized similarly. When installing the radio, make sure to plan the installation carefully and leave additional room in the rear of the radio for cabling and accessory connections; in the front of the radio for access, controls, and cabling; and to the sides of the radio so that you may access and install the trunnion wing screws. 8.5"
7.1"
9.6 9.1 2"
3.5 Figure 1-1. Front View of Dash Mount Transceiver Trunnion Figure 1-2. Side View of Dash Mount Transceiver Trunnion NOTE: The rear accessory connector adds 0.75 in. to the overall length. 1-2 Introduction: Standard Configurations Standard Configurations 1.2 1.2.1 Dash Mount Configuration In the dash mounting version of the XPR 4300/4350/4500/4550, the control head is mounted on the front of the transceiver housing. Electrical connection between the two takes place within the radio via a flexible circuit board between the connectors on the front of the transceiver and at the back of the control head. Figure 1-3. Dash Mount Configuration For details on this configuration, see Section 2.2.1 on page 2-5. NOTE:
1.3 Figure 1-4. Remote Mount Configuration, with 110W transceiver For details on these configurations, see Section 2.2.2 on page 2-8. Base/Control Stations If mobile radio equipment is installed at a fixed location and operated as a control station or as a fixed unit, the antenna installation must comply with the following requirements in order to ensure optimal performance and compliance with the RF energy exposure limits in the standards and guidelines listed in the 68P81095C99 manual:
The antenna should be mounted outside the building on the roof or a tower if at all possible. As with all fixed site antenna installations, it is the responsibility of the licensee to manage the site in accordance with applicable regulatory requirements and may require additional compli-
ance actions such as site survey measurements, signage, and site access restrictions in order to ensure that exposure limits are not exceeded. March 23, 2006 6816812H01 Introduction: Tools Required for XPR 4300/4350/4500/4550 Installations 1-3 1.4 Tools Required for XPR 4300/4350/4500/4550 Installations Tool Part Number 11/32 hex driver RF cable tool HLN6695_ Regular slot screwdriver of Phillips #2 Pin removal tool 1/4 hex driver 6680163F01 6816812H01 March 23, 2006 1-4 Introduction This Page Is Intentionally Left Blank March 23, 2006 6816812H01 Chapter 2 Standard Configurations 2.1 Planning the Installation The XPR 4300/4350/4500/4550 radio operates only in negative ground electrical systems. Before starting the radio installation, make sure that the ground polarity of the vehicle is correct. Accidentally reversing the polarity will not damage the radio, but will cause the cable fuses to blow. Planning is the key to fast, easy radio installation. Before starting the installation, inspect the vehicle and determine how and where you intend to mount the antenna, radio, and accessories. Plan wire and cable runs to provide maximum protection from inching, crushing, and overheating. CAUTION Before installing any electrical equipment, check the vehicle manufacturers user manual. The installation of this device should be completed by an authorized servicer or installer. 2.1.1 Installation Examples Your mobile two-way radio offers various methods of installation, including dash or remote mount. Except for 110W radios, all versions of the XPR 4300/4350/4500/4550 can be either dash or remote mounted (see Figure 2-1 through Figure 2-2). Speaker Antenna 1/4-Wavelength Radio Speaker Antenna 1/4-Wavelength Radio Battery Radio Battery Figure 2-1. Mounting Flexibility in Middle Console Figure 2-2. On Top or Under Dash Mounting 2-2 Standard Configurations: Planning the Installation 2.1.2 Wiring Diagrams Figure 2-3 shows the wiring diagrams for all the possible configurations. The title under each figure identifies the O5 control head configurations. Identify which of these figures shows the configuration that you are installing, and use the diagram when planning the installation. BATTERY
(-) HORN RELAY FUSE LIGHT RELAY MIC CLIP SPEAKER MIC FUSE RED LEAD ANTENNA FIREWALL HOLE DC POWER CABLE ANTENNA CONNECTION TRUNNION MOUNTING SCREW FUSE BLOCK IGNITION CABLE P2
(SEE J2 PINOUT) CONTROL HEAD EMERGENCY SWITCH Figure 2-3. Radio Installation (Dash Mount) with Transceiver
(For complete pin configuration, see Figure 2-4.) March 23, 2006 6816812H01 Standard Configurations: Planning the Installation 2-3 Figure 2-4. Pin Configuration 6816812H01 March 23, 2006 2-4 2.2 Radio Mounting Standard Configurations: Radio Mounting
C a u t i o n CAUTION: DO NOT mount the radio on a plastic dashboard without first reinforcing the dashboard; the weight of the radio may crack or break the dashboard. CAUTION: DO NOT mount the radio on a flat or concave surface where the radio could be partially submersed in water. This is especially important if the cab area of the vehicle is cleaned by spraying with water. If the radio sits in water for a length of time, moisture may seep inside the radio and damage the electronic components. CAUTION: DO NOT allow water to stand in recessed areas of vertically mounted radios. Remove any moisture immediately to prevent it from seeping down into the radio. The mounting location must be accessible and visible. Select a location that will permit routing the RF antenna cable as directly as possible. NOTE: For new or existing installations, use one of the following mounting kits GLN7342B (Low profile mounting bracket), GLN7324B (High profile mounting bracket), RLN4799B (Key Lock mounting bracket) or RLN5999A ( Dim Mounting Bracket). Orient the mounting trunnion as shown in Figure 2-5 RADIO FRONT APPLIES TO RADIOS WITH INTEGRAL OR REMOTE MOUNT CONTROL UNITS Figure 2-5. Trunnion Orientation March 23, 2006 6816812H01 Standard Configurations: Radio Mounting 2-5 2.2.1 Dash Mount with Trunnion 1. Select the location to mount your radio on the transmission hump (see Figure 2-6) or under the dash (see Figure 2-7). When mounting the trunnion on the transmission hump take care the transmission housing is not affected. 2. Using the trunnion mounting bracket as a template, mark the positions of the holes on the mounting surface. Use the innermost four holes for a curved mounting surface such as the transmission hump, and the four outmost holes for a flat surface such as under the dash. 3. Center punch the spots you have marked and realign the trunnion in position. 4. Secure the trunnion mounting bracket with the four self-drilling screws provided (see Figure 2-6 and Figure 2-7). 5. Ensure that the plastic guides are aligned (horizontal) to the grooves of the trunnion. Slide the radio into the grooves until it snaps into place (see Figure 2-6). Secure the radio with the two wing screws provided. Wing Screw Trunnion Plastic Guides Tabs Wing Screw Groove Threaded Hole for Wing Screw Figure 2-6. Transmission Hump Trunnion Mounting Trunnion Wing Screw Holes for Microphone S-Hook Wing Screw 6816812H01 March 23, 2006 Figure 2-7. Below Dash Trunnion Mounting 2-6 Standard Configurations: Power Cable 2.2.2 Locking Kit (Optional) 2.2.2.1 All Radios If an optional locking kit is used (shown in Figure 2-8), position the lock bottom housing on the trunnion before installing the radio mounting screws. Then slip the top lock housing on and remove the key. You can install the lock on either side of the radio, and by rotating it 180, you can also install it on dash installations. Existing Mounting Screw Lock Housing RLN4779_ Locking Kit Lock MAEPF-28266-O Figure 2-8. Locking Kit (Optional) 110W Radios 2.3 Power Cable Route the red radio power cable from the radio to the vehicles battery compartment, using accepted industry methods and standards. Be sure to grommet the firewall hole to protect the cable. Remove the 15-amp (part number 6580283E06), 20-amp (part number 6580283E07) or 30-amp (for 110W) fuse from the fuseholder and connect the red lead of the radio power cable to the positive battery terminal using the hardware provided as shown in Figure 2-9. Connect the black lead to a convenient solid chassis ground point. DO NOT connect the black lead directly to the batterys negative terminal. March 23, 2006 6816812H01 Standard Configurations: Power Cable 2-7 Y R E T T A B E L C H E V I T N E M T R A P M O C T N E M T R A P M O C R O T A R E P O
T N E M T R A P M O C O D A R I I N O T U A C I E L C H E V I H C T W S N O T N G I I I y r a m i r p k c a b l e h t i a v n o i t c e n n o c s s s a h c i d o o g A d n a n o i t a r e p o i o d a r r o f l a i t n e s s e s i l e b a c r e w o p
. t i k l e b a c d n a i o d a r e h t o t e g a m a d t n e v e r p o t
I E L C H E V Y R E T T A B A 0 2 R O A 5 1 E S U F E L B A C R E W O P O D A R I
) T O H Y R E T T A B D E R
F O T R A P I E L C H E V I G N R W I T E M M O R G E T O N E E S C C A N O
E S U F A 4 R O A 3 I N O T N G I I I O D A R
) D E R n h t
i E L B A C E N O H P O R C M I H C I O D A R R E K A E P S r o t c e n n o c r a e R
. l e b a r i s e d s i e m a r f l i e c h e v e h t o t n o i t c e n n o C
) D N U O R G K L B
E L B A C R E W O P O D A R I i i
) g n n n u r r o t a n r e t l a
. e
. i
g n n n u r t o n s i n o i t i n g i s r a c e h t
. F F O r o N O h c t i w s n o n e h w o d a r i e h i t i n g i s r a c e h t h t f o e s u s s e c x e
, y r e t t a b s r a c e h t o t y l t c e r i d e n i l I N O T N G I i I s o d a r e h t t c e n n o c o t e s o o h c u o y f i
n o t i t w e a r e p o o t i o d a r e h t s w o l l a n o i t a r u g i f n o c s h T i
. y r e t t a b s r a c e h t f o e g r a h c s d w o s a n l i i t l u s e r i t u a C l d u o c
E T O N t n u o M h s a D r o f m a r g a D i t c e n n o c r e t n I g n i l b a C
. 9
2 e r u g F i O
6 4 6 7 2
F P E A M
. N O d e n r u t s i h c t i w s n o i t i n g i s r a c e h t n e h w n o i t c n u l f y n o l l i i w o d a r e h t
, h c t i w s n o i t i n g i s r a c e h t o t d e r i w s i e n i l I N O T N G I I s o d a r i e h t f I 6816812H01 March 23, 2006 2-8 2.4 2.5 Standard Configurations: Ignition Sense Cable Ignition Sense Cable Motorola supplies an ignition sense cable and recommends that it be used with every mobile installation. The ignition sense cable allows the radio to be turned on and off with the vehicle ignition switch, and allows the radio to remember the state of the radio on/off switch, even if it is changed while the vehicle is off. For radio ON/OFF control independent of the ignition switch, connect the red ignition cable (yel-
low for remote) (pin 25 of accessory connector) to battery hot at the vehicle fuse block (dash mount only). For radio ON/OFF control via the ignition switch, connect the red ignition cable (yellow for remote) to ignition at the fuse block. Note that for remote mount installations, the red and yellow leads are connected, not the red lead from the rear of the radio. The ignition sense cable uses either a 3-amp (P/N 6580283E01) or 4-amp (P/N 6580283E02) fuse. For other considerations when connecting the ignition cable, see the Basic Service Manual
(Motorola publication part number 6881096C73). Antenna Installation IMPORTANT NOTE: To assure optimum performance and compliance with RF Energy Safety standards, these antenna installation guidelines and instructions are limited to metal-body vehicles with appropriate ground planes and take into account the potential exposure of back seat passengers and bystanders outside the vehicle. NOTE: For mobile radios with rated power of 7 watts or less, the only installation restrictions are to use only Motorola approved antennas and install the antenna externally on metal body vehicles. For mobile radios with rated power greater than 7 Watts, always adhere to all the guidelines and restrictions in section 2.5.1 below. 2.5.1 Selecting an Antenna Site/Location on a Metal Body Vehicle 1. External installation Check the requirements of the antenna supplier and install the vehicle antenna external to a metal body vehicle in accordance with those requirements. 2. Roof top For optimum performance and compliance with RF Energy Safety standards, mount the antenna in the center area of the roof. 3. Trunk lid On some vehicles with clearly defined, flat trunk lids, the antennas of some radio models (see restrictions below) can also be mounted on the center area of the trunk lid. For vehicles without clearly defined, flat trunk lids (such as hatchback autos, sport uitility vehicles, and pick-up trucks), mount the antenna in the center area of the roof. Before installing an antenna on the trunk lid,
- Be sure that the distance from the antenna location on the trunk lid will be at least 85 cm
(33 inches) from the front surface of the rear seat-back to assure compliance with RF Energy Safety standards.
- Ensure that the trunk lid is grounded by connecting grounding straps between the trunk lid and the vehicle chassis. IF THESE CONDITIONS CANNOT BE SATISFIED, THEN MOUNT THE ANTENNA ON THE ROOF TOP!
March 23, 2006 6816812H01 Standard Configurations: Antenna Installation 2-9 4. Mounting restrictions for certain radio models For 40 Watt UHF models, the 1/4 wave antenna should be mounted only in the center area of the roof, not on the trunk lid, to assure compliance with RF Energy Safety standards. 5. Ensure that the antenna cable can be easily routed to the radio. Route the antenna cable as far away as possible from any vehicle electronic control units and associated wiring. 6. Check the antenna location for any electrical interference. 7. Ensure that any other mobile radio antenna on this vehicle is at least one foot (30.48 cm) away from this antenna. NOTE: Any two metal pieces rubbing against each other (such as seat springs, shift levers, trunk and hood lids, exhaust pipes, etc.) in close proximity to the antenna can cause severe receiver interference. 2.5.2 Mini-UHF Connection To ensure a secure connection of an antenna cable's mini-UHF plug to a radio's mini-UHF jack, their interlocking features must be properly engaged. If they are not properly engaged, the system will loosen. Using a tool (pliers or wrench) will not overcome a poor engagement, and is not recommended. NOTE: Applying excessive force with a tool can cause damage to the antenna or the connector (e.g., stripping threads, deforming the collar or connector, or causing the connector to twist in the housing opening and break). The mini-UHF connector tool (Motorola part number HLN6695_) is designed to securely tighten the antenna plugradio jack connection without damaging either the plug or the jack. Motorola recommends the following sequence to ensure proper attachment of the system (see Figure 2-30):
Coax Conductor Plug (Pin) Collar Pulled Back to Flange Flange Mini UHF Jack Cable Figure 2-30. Mini-UHF Connection (as shown on mid-power) 1. Make sure that there is sufficient slack in the antenna cable. 2. Make sure that the collar of the antenna cable plug is loose and does not bind. 3. Make sure that the mini-UHF jack is tight in the radio housing. 4. Slide the collar back against the flange. Insert the antenna cable plugs pin fully into the radio jack, but do not engage the threads. 5. Ensure that the plugs and jacks interlocking features are fully seated. Check this by grasping the crimp on the cable jack, rotating the cable, and noting any movement. If the features are seated correctly, there should be NO movement. 6. Finger-tighten the antenna cable plugs collar onto the radios jack. 6816812H01 March 23, 2006 2-10 Standard Configurations: Speaker 7. Give a final tug, by hand, to the collar, and retighten by hand as firmly as possible. 8. Slip the mini-UHF connector tool over the coaxial cable, using the gap between the tools legs
(see Figure 2-31). Then, slide the tool up onto the plugs knurled collar. Squeeze the two straight legs of the tool firmly together between your thumb and index finger and turn clockwise (as shown) to tighten the collar. It should take 1/4 turn or less. When you feel the tool slipping on the collar, the connection has been properly tightened. The tool can also be used to loosen a tight collar. NOTE: DO NOT use pliers or any other device to grip the tightening tool. It has been designed to allow you to achieve the proper torque on the collar without overtightening. Overtightening the collar can damage the connector and the radio. HLN6695_
(2)Tig h t e n
(1) Squeeze Firmly Together Figure 2-31. Mini-UHF Connector Tool (as shown on mid-power) 2.6 Speaker
C a u t i o n CAUTION: DO NOT ground the radio's speaker leads. This system has a floating speaker output (dc voltage on both leads); damage to the audio circuit will result if either lead is grounded or if they are shorted together. The speaker kit includes a trunnion bracket that allows the speaker to be mounted in a variety of ways. With the trunnion bracket, the speaker can mount permanently on the dashboard or in accessible firewall areas. The trunnion allows the speaker to tilt for best operation. Mount the speaker out of the way so that it will not be kicked or knocked around by the vehicle occupants. Mount the speaker as follows:
1. Use the speaker mounting bracket as a template to mark the mounting hole locations. 2. Use the self-drilling screws provided to fasten the trunnion. 3. Attach the speaker and fasten to the trunnion with two wing screws. 4. Route the speaker wires under the carpet or floor covering, or behind the kick panels. Be sure the wires are out of the way and will not be snagged and broken by the occupants of the vehicle. March 23, 2006 6816812H01 Standard Configurations: Speaker 2-11 Dashboard Trunnion Bracket Firewall OR Figure 2-32. Speaker Mounting MAEPF-25764-O 6816812H01 March 23, 2006 2-12 Standard Configurations: Microphone Hang-Up Clip 2.7 Microphone Hang-Up Clip 2.7.1 Standard Hang-Up Clip The hang-up clip must be within reach of the operator(s). Measure this distance before actually mounting the bracket. Since the bracket has a positive-detent action, the microphone can be mounted in any position. The microphone hang-up clip must be grounded. Use the hang-up clip as a template to locate the mounting holes. To avoid interference when removing the microphone, install the flathead screw in the top clip hole. 2.7.2 Handheld Hang-Up Box Use the hang-up box (HUB) as a template to locate the mounting holes. Be sure the HUB will be within easy reach of the operator. Route the control wire with the male pin to the accessory cable connector at the rear of the radio or cable harness as shown in Figure 2-3. Open the accessory cable connector and connect the HUB control wire to location 3 of the accessory connector. Connect the other control wire from the HUB to a convenient solid chassis ground point. Completing the Installation Complete the installation by connecting the speaker and power wires and plugging in the microphone cable/handheld control unit. Be sure to connect the microphone S-hook to the holes in the trunnion provided (see Figure 2-7) for strain relief (this is not applicable for 110W radios). 2.8 March 23, 2006 6816812H01 Chapter 3 Options and Accessories Installation 3.1 Emergency Pushbutton, Footswitch, Horn Relay, and Light Relay Installation Perform the following installation procedure:
1. Select an appropriate place to mount the option or accessory hardware. 2. Route the accessory-to-control head cables under floor coverings or behind panels so that the vehicle occupants do not snag or break the wires. 3. Attach wires from the accessory to the appropriate wire on the VIP cable. (see Table 3-1 and Table 3-2). Figure 3-1 shows how wires are plugged into the connector and how to use an extraction tool to remove wires. 3.1.1 Emergency Pushbutton or Footswitch Installation Figure 3-1. VIP Connector Detail Mount the switch using the hardware that comes with the kit. Connect the emergency switch wires to a ground pin and a VIP IN pin on the VIP connector. 3.1.2 Horn (External Alarm) Relay Installation Mount the horn relay in a suitable location (normally under the dash). Connect the relay contacts across the horn ring switch, typically found in the steering column. Connect the two control wires to a SW B+ pin and a VIP OUT pin on the VIP connector. 3.1.3 Lights (External Alarm) Relay Installation 3.2 Mount the light relay in a suitable location (normally under the dash). Connect the relay contacts across the headlamp ON/OFF switch. Connect the two control wires to a SW B+ pin and a VIP OUT pin on the VIP connector. Dash-Mount Accessory Installation For dash-mounted configurations, the accessories must be installed through the accessory connector assembly that is located on the rear of the radio, adjacent to the power connector. Motorola-approved accessories are supplied with male terminals crimped to a 20-gauge wire specifically designed to fit the plug of the accessory connector assembly. 3-2 Options and Accessories Installation: Dash-Mount Accessory Installation Insert the male terminal into the accessory connector assembly in the appropriate location and connect the accessory connector assembly in the rear accessory port (see Figure 3-8). Do not use other generic terminals in the plug. Generic terminals can cause electrical intermittencies and may cause damage to the plug. 3.2.1 MDC Emergency Pushbutton or Footswitch Installation Mount the footswitch using the hardware that comes with the kit. Open the accessory cable connector housing; remove the jumper wire. Connect the emergency switch wires to pins 23 and 18
(see Figure 3-2). Close the connector housing; route the finished cable from the switch location to the control head location. NOTE: The emergency footswitch should be attached with A+ unattached. A+ should be attached after succesfully securing the screws in the connector. SPST NORMALLY CLOSED EMERGENCY SWITCH NOTE 1 PIN 23 PIN 18 NOTE 1: REMOVE BLACK JUMPER WIRE INSIDE ACCESSORY CONNECTOR HOUSING. INSERT WIRES FROM EMERGENCY SWITCH ACCESSORIES CONNECTOR D+
Vbus APM 2 (1-wire) SW B+
Spkr-
1 3 5 7 9 2 D-
4 USB / APM Ground 6 APM 1 (1-wire) 8 Power Ground 1 0 Spkr+
Tx Audio 1 1 1 2 Audio Ground Aux Audio Out 1 / RxD 1 3 Aux Audio Out 2 / TxD 1 5 GP5_1 (PTT) GP5_2 (Monitor) GP5_3 (Chan Act) Emerg Sw Ign Sense 1 7 1 9 2 1 2 3 2 5 1 4 1 6 1 8 2 0 2 2 Rx Audio Ground Ground GP5_6 GP5_7 2 4 GP5_8 2 4 VIP_1 (Ext Alarm) Figure 3-2. Emergency Switch Wiring Diagram March 23, 2006 6816812H01 Options and Accessories Installation: Dash-Mount Accessory Installation 3-3 3.2.2 Horn and Lights (External Alarm) Relay For installations that use the horn/lights option, select a suitable location for mounting (normally under the dash) and, referring to Figure 3-3, perform the following procedure:
1. Horn RelayConnect the relay contacts across the horn ring switch, typically found in the steering column. Open the accessory cable connector and connect the two control wires
(male pins) into locations 26 and 7 of the connector. 2. Lights RelayConnect the relay across the headlamp ON/OFF switch, typically found in the steering column. Open the accessory cable connector and connect the two control wires
(male pins) into locations 26 and 7 of the accessory connector. CONNECT ACROSS HORN RING SWITCH AND/OR HEAD LAMP SWITCH SPST N.O. RELAY 12V COIL VIP OUT 1 SWB+
PIN 26 PIN 7 ACCESSORIES CONNECTOR D+
Vbus APM 2 (1-wire) SW B+
Spkr-
1 3 5 7 9 2 D-
4 USB / APM Ground 6 APM 1 (1-wire) 8 Power Ground 1 0 Spkr+
Tx Audio 1 1 1 2 Audio Ground Aux Audio Out 1 / RxD 1 3 Aux Audio Out 2 / TxD 1 5 GP5_1 (PTT) GP5_2 (Monitor) GP5_3 (Chan Act) Emerg Sw Ign Sense 1 7 1 9 2 1 2 3 2 5 1 4 1 6 1 8 2 0 2 2 Rx Audio Ground Ground GP5_6 GP5_7 2 4 GP5_8 2 4 VIP_1 (Ext Alarm) Figure 3-3. Horn/Light Wiring Diagram 3. Squeeze the covers together bending the wires in the strain-relief features. You may need a pair of pliers to seat the assembly covers. 4. Once the covers are fully seated, fasten them with the cover screws. Tighten the screws firmly but do not over-tighten them. Be sure none of the wires are pinched. 5. Reattach the accessory connector assembly to the back of the radio and fasten it by finger-
tightening the jackscrews to prevent any loosening. 6816812H01 March 23, 2006 3-4 Options and Accessories Installation: Dash-Mount Accessory Installation Table 3-1. Rear Accessory Jack Pin Functions Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 Pin Name Pin Function USB+
USB-
VBUS USB GND APM2 APM1 SW B+
PWRGND SPKR-
SPKR+
Tx Audio Audio GND AUX Audio 1 USB + (Data) USB - (Data) USB Power (5V from USB accessory/cable) USB/APM Ground One Wire Data One Wire Data Switched Battery Voltage Ground Speaker - (3.2 ohm minimum impedance) Speaker + (3.2 ohm minimum impedance) Rear External Microphone Input5 Audio Ground PUBLIC Address 1 17 18 19 20 21 22 23 24 25 26 Pin No. 14 15 16 Pin Name Pin Function Rx Audio AUX Audio 2 GND Receive Live Audio 3 PUBLIC Address 21 Ground GPS-1(PTT) GND GPS-2(Monitor) 5V Level GPIO, Monitor 5V Level GPIO, PTT Input2 Ground GPS-6 GPS-3 GPS-7 Input 5V Level GPIO 5V Level GPIO, Channel Activity Function 5V Level GPIO EMERGENCY Emergency Switch Input 1 GPS-7 5V Level GPIO IGN SENSE VIP-1 Ignition Sense6 12V Tolerant, 5V GPIO, External Alarm 1 This pin must be connected to ground by jumper on accessory cable if emergency is disabled, even if disabled by CPS. If enabled, this line must be grounded via a switch, which is normally closed. The emergency debounce time is programmable via CPS. 2 Pulling this line to ground will activate PTT function, activating the AUX_MIC input. 3 Fixed level (independent of volume level) received audio signal, including alert tones. Flat or de-emphasis are pro-
grammed by CPS. Output voltage is approximately 100 mVrms per 1kHz of deviation. The DC offset is 1.4V. 4 This output is used to detect when a rear microphone accessory is taken off-hook, to override PL to alert the user to busy traffic prior to transmitting. 5 This microphone signal is independent of the microphone signal on the front microphone connector. The nominal input level is 80mVrms for 60% deviation when used for motorcycle, but can also support 300 mVrms for future APCO accessories. The DC impedance is 660 ohms and the AC impedance is 560 ohms. 6 See Table 2-1 in Chapter 2 for wiring options. Note: Please see the XPR 4300/4350/4500/4550 Basic Service manual (Motorola publication part number 6816816H01) for more detailed descriptions of these pins. March 23, 2006 6816812H01 Appendix A Replacement Parts Ordering A.1 Basic Ordering Information When ordering replacement parts or equipment information, the complete identification number should be included. This applies to all components, kits, and chassis. If the component part number is not known, the order should include the number of the chassis or kit of which it is a part, and sufficient description of the desired component to identify it. Crystal orders should specify the crystal type number, crystal and carrier frequency, and the model number in which the part is used. The XPR 4300/4350/4500/4550 Digital Mobile Radio Basic Service Manual (Motorola publication part number 6816816H01) includes complete parts lists and parts numbers. A.2 Motorola Online Motorola Online users can access our online catalog at https://www.motorola.com/businessonline To register for online access:
Domestic customers: please call 800-814-0601 (U.S. and Canada). International customers: please go to https://www.motorola.com/businessonline and click on Sign Up Now. A.3 Mail Orders Send written orders to the following addresses:
Replacement Parts/
Test Equipment/Manuals/
Crystal Service Items:
Motorola Inc. Radio Products and Services Division*
Attention: Order Processing 2200 Galvin Drive Elgin, IL 60123 U.S.A. Federal Government Orders:
International Orders:
Motorola Inc. U.S. Federal Government Markets Division Attention: Order Processing 7230 Parkway Drive Landover, MD 21076 U.S.A. Motorola Inc. Radio Products and Services Division*
Attention: Order Processing 2200 Galvin Drive Elgin, IL 60123 U.S.A. A-2 A.4 A.5 Replacement Parts Ordering: Telephone Orders Telephone Orders Radio Products and Services Division*
(United States and Canada) 7:00 AM to 7:00 PM (Central Standard Time) Monday through Friday (Chicago, U.S.A.) 1-800-422-4210 1-847-538-8023 (International Orders) U.S. Federal Government Markets Division (USFGMD) 1-800-826-1913 Federal Government Parts - Credit Cards Only 8:30 AM to 5:00 PM (Eastern Standard Time) Fax Orders Radio Products and Services Division*
(United States and Canada) 1-800-622-6210 1-847-576-3023 (International) USFGMD
(Federal Government Orders) 1-800-526-8641 (For Parts and Equipment Purchase Orders) A.6 Parts Identification Radio Products and Services Division*
(United States and Canada) 1-800-422-4210, menu 3 A.7 Product Customer Service Customer Response Center
(Non-technical Issues) 1-800-247-2346 FAX:1-800-247-2347
*The Radio Products and Services Division (RPSD) was formerly known as the Customer Care and Services Division (CCSD) and/or the Accessories and Aftermarket Division (AAD). March 23, 2006 6816812H01 Glossary Glossary This glossary contains an alphabetical listing of terms and their definitions that are applicable to ASTRO portable and mobile subscriber radio products. Term A/D Abacus IC ADC ADDAG ALC analog Analog-to-Digital, Digital-to-Analog and Glue analog-to-digital conversion analog-to-digital converter automatic level control band BBP baseband interface port BGA ball grid array CODEC coder/decoder Definition See analog-to-digital conversion. A custom integrated circuit providing a digital receiver intermediate frequency (IF) backend. See analog-to-digital converter. See Analog-to-Digital, Digital-to-Analog and Glue. See automatic level control. Refers to a continuously variable signal or a circuit or device designed to handle such signals. See also digital. An integrated circuit designed to be an interface between the radios DSP, which is digital, and the analog transmitter and receiver ICs. Conversion of an instantaneous dc voltage level to a corresponding digital value. See also D/A. A device that converts analog signals into digital data. See also DAC. A circuit in the transmit RF path that controls RF power amplifier output, provides leveling over frequency and voltage, and protects against high VSWR. Frequencies allowed for a specific purpose. See baseband interface port. Synchronous serial interface to the transceiver board used to transfer transmit and receive audio data. See ball grid array. A type of IC package characterized by solder balls arranged in a grid that are located on the underside of the package. See coder/decoder. A device that encodes or decodes a signal. Glossary-2 Term CPS Customer Programming Software D/A DAC default digital digital-to-analog conversion digital-to-analog converter Digital Private-Line digital signal processor digital signal processor code DPL DSP DSP code DTE DTMF dual tone multi-
frequency FCC Definition See Customer Programming Software. Software with a graphical user interface containing the feature set of an ASTRO radio. See digital-to-analog conversion. See digital-to-analog converter. A pre-defined set of parameters. Refers to data that is stored or transmitted as a sequence of discrete symbols from a finite set; most commonly this means binary data represented using electronic or electromagnetic signals. See also analog. Conversion of a digital signal to a voltage that is proportional to the input value. See also A/D. A device that converts digital data into analog signals. See also ADC. A type of digital communications that utilizes privacy call, as well as memory channel and busy channel lock out to enhance communication efficiency. A microcontroller specifically designed for performing the mathematics involved in manipulating analog information, such as sound, that has been converted into a digital form. DSP also implies the use of a data compression technique. Object code executed by the Digital Signal Processor in an ASTRO subscriber radio. The DSP is responsible for computation-intensive tasks, such as decoding ASTRO signaling. See Digital Private-Line. See also PL. See digital signal processor. See digital signal processor code. Data terminal equipment: i.e., a computer. See dual tone multi-frequency. The system used by touch-tone telephones. DTMF assigns a specific frequency, or tone, to each key so that it can easily be identified by a microprocessor. Federal Communications Commission. March 23, 2006 6816812H01 Term firmware FGU flash frequency frequency generation unit General-Purpose Input/Output GPIO host code IC IF inbound signaling word integrated circuit ISW kHz kilohertz Glossary-3 Definition Code executed by an embedded processor such as the Host or DSP in a subscriber radio. This type of code is typically resident in non-volatile memory and as such is more difficult to change than code executed from RAM. See frequency generation unit. A non-volatile memory device similar to an EEPROM. Flash memory can be erased and reprogrammed in blocks instead of one byte at a time. Number of times a complete electromagnetic-wave cycle occurs in a fixed unit of time (usually one second). This unit generates ultra-stable, low-phase noise master clock and other derived synchronization clocks that are distributed throughout the communication network. Pins whose function is programmable. See General-Purpose Input/Output. Object code executed by the host processor in an ASTRO subscriber radio. The host is responsible for control-oriented tasks such as decoding and responding to user inputs. See integrated circuit. Intermediate Frequency. Data transmitted on the control channel from a subscriber unit to the central control unit. An assembly of interconnected components on a small semiconductor chip, usually made of silicon. One chip can contain millions of microscopic components and perform many functions. See inbound signaling word. See kilohertz. One thousand cycles per second. Used especially as a radio-frequency unit. See liquid-crystal display. See light emitting diode. An electronic device that lights up when electricity is passed through it. LCD LED light emitting diode liquid-crystal display An LCD uses two sheets of polarizing material with a liquid-crystal solution between them. An electric current passed through the liquid causes the crystals to align so that light cannot pass through them. 6816812H01 March 23, 2006 Glossary-4 Term LO low-speed handshake LSH Master In Slave Out Master Out Slave In MCU MDC MDI MHz Megahertz microcontroller unit MISO MOSI multiplexer MUX NiCd NiMH OMPAC open architecture oscillator OSW OTAR outbound signaling word over-molded pad-
array carrier March 23, 2006 Definition Local oscillator. 150-baud digital data sent to the radio during trunked operation while receiving audio. See low-speed handshake. SPI data line from a peripheral to the MCU. SPI data line from the MCU to a peripheral. See microcontroller unit. Motorola Digital Communications. MCU/DSP Interface internal to the Patriot IC. See Megahertz. One million cycles per second. Used especially as a radio-frequency unit. Also written as C. A microprocessor that contains RAM and ROM components, as well as communications and programming components and peripherals. See Master In Slave Out. See Master Out Slave In. An electronic device that combines several signals for transmission on some shared medium (e.g., a telephone wire). See multiplexer. Nickel-cadmium. Nickel-metal-hydride. See over-molded pad-array carrier. A controller configuration that utilizes a microprocessor with extended ROM, RAM, and EEPROM. An electronic device that produces alternating electric current and commonly employs tuned circuits and amplifying components. See outbound signaling word. See over-the-air rekeying. Data transmitted on the control channel from the central controller to the subscriber unit. A Motorola custom IC package, distinguished by the presence of solder balls on the bottom pads. 6816812H01 Term Definition Glossary-5 over-the-air rekeying Allows the dispatcher to remotely reprogram the encryption keys in the PA paging Patriot IC PC Board phase-locked loop PL PLL private-line tone squelch Programmable Read-Only Memory programming cable PROM PTT Push-to-Talk radio frequency radio frequency power amplifier Radio Service Software RAM random access memory read-only memory radio. Power amplifier. One-way communication that alerts the receiver to retrieve a message. A dual-core processor that contains an MCU and a DSP in one IC package. Printed Circuit Board. Also referred to as a PCB. A circuit in which an oscillator is kept in phase with a reference, usually after passing through a frequency divider. See private-line tone squelch. See phase-locked loop. A continuous sub-audible tone that is transmitted along with the carrier. See also DPL. A memory chip on which data can be written only once. Once data has been written onto a PROM, it remains there forever. A cable that allows the CPS to communicate directly with the radio using RS232. See Programmable Read-Only Memory. See Push-to-Talk. The switch or button usually located on the left side of the radio which, when pressed, causes the radio to transmit. When the PTT is released, the unit returns to receive operation. The portion of the electromagnetic spectrum between audio sound and infrared light (approximately 10 kHz to 10 GHz). Amplifier having one or more active devices to amplify radio signals. Not used with XTL 5000. See Customer Programming Software. See random access memory. A type of computer memory that can be accessed randomly; that is, any byte of memory can be accessed without touching the preceding bytes. A type of computer memory on which data has been prerecorded. Once data has been written onto a ROM chip, it cannot be removed and can only be read. 6816812H01 March 23, 2006 Glossary-6 Term real-time clock receiver registers repeater repeater/talkaround RESET RF RF PA ROM RPCIC RPT/TA RS232 RSS RTC RX RX DATA SAP SCI IN Serial Audio CODEC Port Serial Communication Interface Input Line SCI IN Serial Peripheral Interface Definition A module that keeps track of elapsed time even when a computer is turned off. Electronic device that amplifies RF signals. A receiver separates the audio signal from the RF carrier, amplifies it, and converts it back to the original sound waves. Short-term data-storage circuits within the microcontroller unit or programmable logic IC. Remote transmit/receive facility that re-transmits received signals in order to improve communications range and coverage (conventional operation). A conventional radio feature that permits communication through a receive/transmit facility, which re-transmits received signals in order to improve communication range and coverage. Reset line: an input to the microcontroller that restarts execution. See radio frequency. See radio frequency power amplifier. See read-only memory. Regulator/power control IC. See repeater/talkaround. A common interface standard for data communications equipment. See Radio Service Software. See real-time clock. Receive. Recovered digital data line. See Serial Audio CODEC Port. Serial Communications Interface Input line. SSI to and from the GCAP II IC CODEC used to transfer transmit and receive audio data. A full-duplex (receiver/transmitter) asynchronous serial interface. See Serial Communication Interface Input Line. How the microcontroller communicates to modules and ICs through the CLOCK and DATA lines. March 23, 2006 6816812H01 Term signal Signal Qualifier mode softpot software software potentiometer spectrum SPI squelch SRAM SSI Standby mode static RAM Synchronous Serial Interface system central controllers system select thin small-outline package time-out timer TOT transceiver transmitter TSOP 6816812H01 Glossary-7 Definition An electrically transmitted electromagnetic wave. An operating mode in which the radio is muted, but still continues to analyze receive data to determine RX signal type. See software potentiometer. Computer programs, procedures, rules, documentation, and data pertaining to the operation of a system. A computer-adjustable electronic attenuator. Frequency range within which radiation has specific characteristics. See Serial Peripheral Interface. Muting of audio circuits when received signal levels fall below a pre-
determined value. With carrier squelch, all channel activity that exceeds the radios preset squelch level can be heard. See static RAM. See Synchronous Serial Interface. An operating mode in which the radio is muted but still continues to monitor data. A type of memory used for volatile, program/data memory that does not need to be refreshed. DSP interface to peripherals that consists of a clock signal line, a frame synchronization signal line, and a data line. Main control unit of the trunked dispatch system; handles ISW and OSW messages to and from subscriber units (See ISW and OSW). The act of selecting the desired operating system with the system-select switch (also, the name given to this switch). A type of dynamic random-access memory (DRAM) package that is commonly used in memory applications. A timer that limits the length of a transmission. See time-out timer. Transmitter-receiver. A device that both transmits and receives analog or digital signals. Also abbreviated as XCVR. Electronic equipment that generates and amplifies an RF carrier signal, modulates the signal, and then radiates it into space. See thin small-outline package. March 23, 2006 Glossary-8 Term TX UART UHF Universal Asynchronous Receiver Transmitter Universal Serial Bus USB VCO VHF VIP VOCON vocoder vocoder/controller voice encoder voltage-controlled oscillator Definition Transmit. See also Universal Asynchronous Receiver Transmitter. Ultra-High Frequency. A microchip with programming that controls a computer's interface to its attached serial devices. An external bus standard that supports data transfer rates of 12 Mbps. See Universal Serial Bus. See voltage-controlled oscillator. Very-High Frequency. Vehicle Interface Port. See vocoder/controller. An electronic device for synthesizing speech by implementing a compression algorithm particular to voice. See also voice encoder. A PC board that contains an ASTRO radios microcontroller, DSP, memory, audio and power functions, and interface support circuitry. The DSP-based system for digitally processing analog signals, and includes the capabilities of performing voice compression algorithms or voice encoding. See also vocoder. An oscillator in which the frequency of oscillation can be varied by changing a control voltage. March 23, 2006 6816812H01 Index Index installation examples ............................................. 2-1 radio dimensions ................................................... 1-1 trunnion ................................................................. 2-5 Numerics 100W radios configurations ........................................................1-2 A accessories connector assembly ...............................................3-1 installing dash mount ........................................................3-1 emergency pushbutton .......................................3-1 footswitch ...........................................................3-1 horn relay ...........................................................3-1 light relay ............................................................3-1 remote mount .....................................................3-1 cable, see Cables, antenna connection .............................................................2-9 diagrams .......................................................2-9, 2-10 installing .................................................................2-8 mounting ................................................................2-8 site .........................................................................2-8 antenna B base stations .............................................................1-2 black lead ..................................................................2-6 C cables accessory ....................................... 2-12, 3-1, 3-2, 3-3 antenna ...........................................................2-4, 2-9 diagrams ................................................. 2-2, 2-7, 2-9 ignition ...................................................................2-8 ignition sense .........................................................2-8 power .....................................................................2-6 programming ......................................................... A-5 tools .......................................................................1-3 100W radios ...........................................................1-2 dash mount ............................................................1-2 configurations control head dash mount ............................................................1-2 see also specific model names control stations ..........................................................1-2 D dash mount accessories installations ........................................3-1 configuration ..........................................................1-2 installation ..............................................................2-2 E emergency footswitch ........................................3-1, 3-2 emergency pushbutton ......................................3-1, 3-2 external alarm see also Horn relay or Light relay F footswitch, emergency .......................................3-1, 3-2 G green lead ................................................................. 2-8 H horn relay ...........................................................3-1, 3-3 I ignition installation cable ...................................................................... 2-8 examples ............................................................... 2-1 J J2 pin configuration .................................................... 2-2 L leads black ...................................................................... 2-6 green .....................................................................2-8 orange ................................................................... 2-8 light relay ............................................................3-1, 3-3 locking kit, installing .................................................. 2-6 M microphone hang-up box ........................................................2-12 hang-up clip, standard .........................................2-12 S-hook ..........................................................2-5, 2-12 mounting configurations ............................................ 2-4 dash ................................................................1-2, 2-5 mounting, antenna restrictions ............................................................. 2-9 roof top .................................................................. 2-8 trunk lid .................................................................. 2-8 Index-2 O orange lead ............................................................... 2-8 ordering replacement parts .......................................A-1 P parts, ordering replacement ......................................A-1 pin functions ................................................................ 3-4 ground ................................................................... 3-1 removal tool ........................................................... 1-3 SW B+ ................................................................... 3-1 VIP out .................................................................. 3-1 pin configurations J2 .......................................................................... 2-2 pushbutton, emergency ..................................... 3-1, 3-2 R rear accessory jack, see J2 relays horn ................................................................ 3-1, 3-3 light ................................................................. 3-1, 3-3 remote mount accessory installations .......................................... 3-1 installation examples ............................................. 2-1 replacement parts, ordering ......................................A-1 S speaker connecting ........................................................... 2-12 mounting .................................................... 2-10, 2-11 T tools, required ........................................................... 1-3 trunnion below dash mounting ............................................ 2-5 bracket for speaker ............................................. 2-10 dash mount ........................................................... 2-5 locking kit .............................................................. 2-6 mounting bracket .................................................. 2-5 orientation ............................................................. 2-4 transmission hump mounting ................................ 2-5 V VIP connector .............................................................. 3-1 W W4 control head ....................................................... 3-1 W5 control head ....................................................... 3-1 W7 control head ....................................................... 3-1 W9 control head ....................................................... 3-1 wiring diagrams ........................................................ 2-2 March 23, 2006 6816812H01
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2007-10-25 | 136 ~ 174 | TNB - Licensed Non-Broadcast Station Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2007-10-25
|
||||
1 | Applicant's complete, legal business name |
Motorola Solutions, Inc.
|
||||
1 | FCC Registration Number (FRN) |
0025009739
|
||||
1 | Physical Address |
1303 East Algonquin Road
|
||||
1 |
Schaumburg, Illinois 60196
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
n/a | ||||||
app s | FCC ID | |||||
1 | Grantee Code |
ABZ
|
||||
1 | Equipment Product Code |
99FT3083
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
R******** S******
|
||||
1 | Telephone Number |
847-3********
|
||||
1 | Fax Number |
847-5********
|
||||
1 |
B******@motorolasolutions.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 12/09/2007 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TNB - Licensed Non-Broadcast Station Transmitter | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | MOTOTRBO VHF 25 W Mobile Radio | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Listed output power is rated conducted; maximum conducted output power is 30 W as allowed by 47 CFR 90.205(r). This transmitter must be restricted to work related operations in an Occupational / Controlled RF exposure environment, not exceeding a maximum transmitting duty factor of 50%. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration, and the exposure conditions and/or duration of their passengers and bystanders, to comply with the General Population / Uncontrolled MPE limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements. Users must be provided with the training information, antenna installation and transmitter operating conditions for satisfying RF exposure compliance. The antenna(s) used for this transmitter must be installed to provide separation distances as described in filing. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
n/a | ||||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 9 | BC EF | 136 | 174 | 25 | 1.5 ppm | 11K0F3E | |||||||||||||||||||||||||||||||||
1 | 2 | 9 | BC EF | 136 | 174 | 25 | 1.5 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
1 | 3 | 9 | BC EF | 136 | 174 | 25 | 1.5 ppm | 7K60FXD | |||||||||||||||||||||||||||||||||
1 | 4 | 9 | BC EF | 136 | 174 | 25 | 1.5 ppm | 7K60FXE |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC