all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Safety Manual | Users Manual | 2.06 MiB | ||||
1 |
|
User Manual/Guide | Users Manual | 4.13 MiB | ||||
1 | Attestation Statements | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | ID Label/Location Info | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | Cover Letter(s) | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | Safety Manual | Users Manual | 2.06 MiB |
m XPRTM 3000 Series Quick Reference Guide and Safety Manual Regulatory Compliance and Product Safety for Portable Two-Way Radios C a u t i o n BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION AND OPERATIONAL INSTRUCTIONS FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. ALSO READ THE OPERATIONAL INSTRUCTIONS FOR SAFE USAGE. FOR RADIOS THAT HAVE BEEN APPROVED AS INTRINSICALLY SAFE, READ THE INSTRUCTIONS AND INFORMATION ON INTRINSIC SAFETY ON PAGE 12 OF THIS BOOKLET. 1 English RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific 2 English operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits:
http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/
index.html Federal Communication Commission
(FCC) Regulations The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for portable two-
way radios before they can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. 3 English This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/
controlled RF exposure environments at operating duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. NOTE: The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5%
talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:
United States Federal Communications Commission (FCC), Code of Federal Regulations;
47 CFR et seq. FCC, OET Bulletin 65 Institute of Electrical and Electronic Engineers
(IEEE) C95.1 International Commission on Non-Ionizing Radiation Protection (ICNIRP) Ministry of Health (Canada) Safety Code 6 Australian Communications Authority Industry Canada RSS-102 Radiocommunications Standard et seq. ANATEL ANNEX to Resolution No. 303 et seq. 4 English RF Exposure Compliance and Control Guidelines and Operating Instructions To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures. Guidelines:
DO NOT remove the RF Exposure Label from the device. User awareness instructions should accompany device when transferred to other users. DO NOT use this device if the operational requirements described herein are not met. Operating Instructions Transmit no more than the rated duty factor of 50%
of the time. To transmit (talk), push the Push-To-
Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). Two-Way Radio Operation Hold the radio in a vertical position in front of the face with the microphone
(and other parts of the radio including the antenna) at least one inch (2.5 centimeters) away from the nose or lips. Antenna should be kept away from the eye. Keeping the radio at a proper distance is important since RF exposures decrease with increasing distance from the antenna. 5 English Body Worn Operation When worn on the body, always place the radio in a Motorola-approved clip, holder, holster, case, or body harness for this product. Using approved body-worn accessories is important because the use of non-Motorola-approved accessories may result in exposure levels, which exceed the FCC occupational/controlled environment RF exposure limits. DO NOT hold the antenna when the radio is transmitting. Holding the antenna affects call quality and may cause the radio product to operate at higher power level than needed. DO NOT touch the metal surface of the antenna (in extended position) when the radio is transmitting. RF discomfort may result. Approved Accessories Use only Motorola-approved supplied or replacement antennas, batteries, and accessories. Use of non-Motorola-approved antennas, batteries, and accessories may exceed the FCC (IEEE) and ICNIRP RF exposure guidelines. For a list of Motorola-approved accessories, visit the following website, which lists approved accessories for your radio model:
www.motorolasolutions.governmentandenterprise Additional Information For additional information on exposure requirements or other training information, visit:
www.motorolasolutions.com/rfhealth 6 English Electromagnetic Interference/
Compatibility NOTE: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Aircraft When instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions. Medical Devices Pacemakers The Advanced Medical Technology Association
(AdvaMed) recommends that a minimum separation of 6 inches (15 centimeters) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with those of the U.S. Food and Drug Administration. Persons with pacemakers should:
ALWAYS keep the radio more than 6 inches (15 centimeters) from their pacemaker when the radio is turned ON. Not carry the radio in the breast pocket. 7 English Use the ear opposite the pacemaker to minimize the potential for interference. Turn the radio OFF immediately if there is any reason to suspect that interference is taking place. Hearing Aids Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives. Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. Use of Communication Devices While Driving Always check the laws and regulations on the use of radios in the areas where you drive. Give full attention to driving and to the road. Use hands-free operation, if available. Pull off the road and park before making or answering a call, if driving conditions or regulations so require. Acoustic Safety Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the radio's volume, the less time is required before your hearing could be affected. Hearing damage from loud noise is sometimes undetectable at first and can have a cumulative effect. 8 English To protect your hearing:
Use the lowest volume necessary to do your job. Turn up the volume only if you are in noisy Turn down the volume before adding headset or surroundings. earpiece. Limit the amount of time you use headsets or earpieces at high volume. When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear. Operational Warnings W A R N I N G For Vehicle With Air Bags:
Refer to vehicle manufacturer's manual prior to installation of electronic equipment to avoid interference with air bag wiring. DO NOT place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. 9 English W A R N I N G Potentially Explosive Atmospheres
(Explosive atmospheres refers to hazard classified locations that may contain hazardous gas, vapors, or dusts.) Turn off your radio prior to entering any area with a potentially explosive atmosphere unless it is a portable radio type especially qualified for use in such areas as Intrinsically Safe
(for example, Factory Mutual, CSA, UL, or CENELEC). DO NOT remove, install, or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often, but not always, posted. 10 English W A R N I N G Blasting Caps and Blasting Areas To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: "Turn off two-way radio." Obey all signs and instructions. Operational Cautions C a u t i o n Antennas DO NOT use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. Batteries All batteries can cause property damage and/or bodily injury, such as burns, if a conductive material such as jewelry, keys, or beaded chains touches exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse, or other container with metal objects. 11 English Intrinsically Safe Radio Information The Intrinsically safe approval unit refers to a product that has been approved as intrinsically safe by an approval agency (for example FM Approvals, CSA, UL, or Cenelec) and certifies that a particular product meets the Agency's applicable intrinsic safety standards for specific types of hazardous classified locations. A portable radio that has been approved for intrinsic safety will have Approval label attached to the radio to identify the unit as being Approved for specified hazardous atmospheres. This label specifies the hazardous Class/Division/Group along with the part number of the battery that must be used. The Intrinsically Safe Approval Label will be located on the portable radio unit. Operational Cautions for Intrinsic Safe Equipment C a u t i o n DO NOT operate radio communications equipment in a hazardous atmosphere unless it is a type especially qualified
(for example, FM, UL, CSA, or CENELEC approved). An explosion or fire may result. 12 English Operational Cautions for Intrinsic Safe Equipment C a u t i o n DO NOT operate a radio unit that has been approved as intrinsically safe product in a hazardous atmosphere if it has been physically damaged (for example, cracked housing). An explosion or fire may result. DO NOT replace or charge batteries in a hazardous atmosphere. Contact sparking may occur while installing or removing batteries and cause an explosion or fire. Warnings for Radios Approved as Intrinsically Safe Radios must ship from the Motorola manufacturing facility with the hazardous atmosphere capability and the intrinsic safety approval labelling (FM, UL, CSA, CENELEC). Radios will not be upgraded to this capability and labeled once they have been shipped to the field. A modification changes the units hardware from its original design configuration. Modifications can only be made by the original product manufacturer. 13 English W A R N I N G DO NOT replace or change accessories in a hazardous atmosphere. Contact sparking may occur while installing or removing accessories and cause an explosion or fire. Turn the radio off before removing or installing a battery or accessory. DO NOT disassemble an intrinsically safe product in any way that exposes the internal circuits of the unit. Failure to use an intrinsically safe approved battery or Approved accessories specifically approved for the radio unit may result in the dangerously unsafe condition of an unapproved radio combination being used in a hazardous location. Unauthorized or incorrect modification of the intrinsically safe approved Product will negate the approval rating of the product. Incorrect repair or relabeling of any intrinsically safe Agency-approved radio could adversely affect the Approval rating of the unit. 14 English W A R N I N G Repair W A R N I N G Use of a radio that is not intrinsically safe in a hazardous atmosphere could result in serious injury or death. REPAIRS FOR MOTOROLA PRODUCTS WITH INTRINSICALLY SAFE APPROVAL ARE THE RESPONSIBILITY OF THE USER. Repairs to a Motorola FM approved radio product should only be done at a location that has been FM audited under the FM 3605 repairs and service standard. Contact Motorola for assistance regarding repairs and service of Motorola intrinsically safe equipment. 15 English A repair constitutes something done internally to the unit that would bring it back to its original condition. Items not considered as repairs are those in which an action is performed on a unit which does not require the outer casing of the unit to be opened in a manner that exposes the internal electrical circuits of the unit. Do Not Substitute Options or Accessories The Motorola communications equipment certified as intrinsically safe by the approving agency, (FM, UL, CSA, CENELEC) is tested as a complete system which consists of the listed agency Approved portable, Approved battery, and Approved accessories or options, or both. This Approved portable and battery combination must be strictly observed. There must be no substitution of items, even if the substitute has been previously Approved with a different Motorola communications equipment unit. Approved configurations are listed by the Approving Agency (FM, UL, CSA, CENELEC). The Intrinsically Safe Approval Label affixed to radio refers to the intrinsically safe classification of that radio product, and the approved batteries that can be used with that system. The manual PN referenced on the Intrinsically Safe Approval Label identifies the approved Accessories and or options that can be used with that portable radio unit. Using a non-Motorola-intrinsically-safe battery and or accessory with the Motorola approved radio unit will void the intrinsically safe approval of that radio unit. 16 English m XPR 3000 Series Digital Portable Radios Quick Reference Card Radio Controls Limited Keypad Radio
NOTE: Refer to User Guide for more details on your radio's operations/features. Record your radios programmable button functions in the blanks provided. SP represents short press, LP represents long press. 1 2 3 4 5 6 7 8 9 10 18 17 16 15 14 13 12 11 17 English
Non-Keypad Radio 1 2 3 4 5 6 7 18 17 16 1 2 3 4 5 6 Channel Selector Knob On/Off/Volume Control Knob LED Indicator Push-to-Talk (PTT) Button Microphone Side Button 1 (Programmable) SP: ____________LP: ___________ 18 English 7 8 9 10 11 12 13 14 15 16 17 18 Side Button 2(Programmable) SP: ___________ LP: ___________ Left Navigation Button Menu Button Front Button P1 (Programmable) SP: ___________ LP: ___________ OK Button Front Button P2 (Programmable) SP: ___________ LP: ___________ Back/Home Button Right Navigation Button Display Speaker Universal Connector for Accessories Antenna 19 English Display Icons The following are the icons that appear on the radios display. Received Signal Strength Indicator
(RSSI) The number of bars displayed represents the radio signal strength. Four bars indi-
cate the strongest signal. This icon is only displayed while receiving. Battery The number of bars (0 4) shown indi-
cates the charge remaining in the bat-
tery.Blinks when the battery is low. Emergency Radio is in Emergency mode. Notifications Notification list is not empty. Scan*
Scan feature is enabled. 20 English Scan Priority 1*
Radio detects activity on channel/group designated as Priority 1. Scan Priority 2 *
Radio detects activity on channel/group designated as Priority 2. Vote Scan Vote scan feature is enabled. Monitor Selected channel is being monitored. Talkaround*
In the absence of a repeater, radio is cur-
rently configured for direct radio to radio communication. Site Roaming*
The site roaming feature is enabled. Secure The Privacy feature is enabled. Unsecure The Privacy feature is disabled. 21 English Tones Disable Tones are turned off. OR Power Level Radio is set at Low power. Radio is set at High power. Call Icons The following icons appear during a call, and in the Contacts list to indicate ID type. Private Call Indicates a Private Call in progress. In the Contacts list, it indicates a subscriber alias (name) or ID (number). Group Call/All Call Indicates a Group Call or All Call in prog-
ress. In the Contacts list, it indicates a group alias (name) or ID (number). 22 English Sent Items Icons The following icons appear at the top right corner of the radios display in the Sent Items folder. OR Sent Successfully The text message is sent successfully. OR Send Failed The text message cannot be sent. In-Progress The text message to a subscriber alias or ID is pending transmission, followed by waiting for acknowledgement. OR The text message to a group alias or ID is pending transmission. 23 English LED Indicator Blinking red Radio is transmitting at low battery condition, receiving an emergency transmission or has failed the self-test upon powering up. Solid green Radio is powering up, or transmitting. Also indicates full charge of the battery when Battery Strength button is pressed. Blinking green Radio is receiving a non-privacy-
enabled call or data, or detecting activity over the air. Double blinking green Radio is receiving a privacy-enabled call or data . Solid yellow Radio is monitoring a conventional channel. Blinking yellow Radio is scanning for activity or receiving a Call Alert. Double blinking yellow Radio is no longer connected to the repeater while in Capacity Plus, all Capacity Plus channels are currently busy, Auto Roaming is enabled, radio is actively searching for a new site. Also indicates radio has yet to respond to a group call alert, or radio is locked. NOTE: For Capacity Plus, there is no LED indication when the radio is detecting activity over the air. 24 English Charging the Battery Your radio is powered by a Nickel Metal-Hydride
(NiMH) or Lithium-Ion (Li-lon) battery. To avoid damage and comply with warranty terms, charge the battery using a Motorola charger exactly as described in the charger user guide. Charge a new battery 14 to 16 hours before initial use for best performance. IMPORTANT: ALWAYS charge your IMPRES battery with an IMPRES charger for optimized battery life and valuable battery data. IMPRES batteries charged exclusively with IMPRES chargers receive a 6-
month capacity warranty extension over the standard Motorola Premium battery warranty duration. 25 English Attaching the Battery Align the battery with the rails on the back of the radio. Press the battery firmly, and slide upward until the latch snaps into place. Slide battery latch into lock position. To remove the battery, turn the radio off. Move the battery latch into unlock position and hold, and slide the battery down and off the rails. Battery Latch 26 English Attaching the Antenna With the radio turned off, set the antenna in its receptacle and turn clockwise. Make sure that the antenna is tightened securely to the radio. To remove the antenna, turn the antenna counterclockwise. 27 English Attaching the Belt Clip Align the grooves on the clip with those on the battery and press downward until you hear a click. To remove the clip, press the belt clip tab away from the battery. Using a key may be helpful. Then slide the clip upward and away from the radio. 28 English Attaching the Universal Connector Cover (Dust Cover) The universal connector is located on the antenna side of the radio. It is used to connect MOTOTRBO accessories to the radio. Insert the hooked end of the cover into the slots above the universal connector. Press downward on the cover to seat the lower tab properly into the RF connector. Turn the thumbscrew clockwise to secure Universal Connector the connector cover to the radio. To remove the universal connector cover, press down on the cover and turn the thumbscrew counterclockwise. Lift the cover up, slide the connector cover loop upwards, and remove it from the attached antenna. Replace the dust cover when the universal connector is not in use. 29 English Powering Up the Radio Rotate the On/Off/Volume Control Knob clockwise until you hear a click. You see MOTOTRBO (TM) on the radios display momentarily, followed by a welcome message or welcome image. The LED lights up solid green and the Home screen lights up if the backlight setting is set to turn on automatically.
*If enabled, a brief tone sounds indication that the power up test is successful.
*To turn off the radio, rotate the knob clockwise until you hear a click. Adjusting the Volume To increase the volume, turn the On/Off Volume Control Knob clockwise. To decrease the volume, turn this knob counterclockwise. NOTE: Your radio can be programmed to have a minimum volume offset where the volume level cannot be turned down fully. Check with your dealer or system administrator for more information. 30 English Accessing the Radio from Password Limited Keypad Radio
1. Power up the radio. 2. You will be prompt to enter a four-digit password. 3. Enter your current four-digit password. Press <
or > to choose each digits numeric value (0-9). Press > or c to move to next digit. Each digit changes to . Press e to confirm your selection. 4. You hear a positive indicator tone for every digit pressed. Press < to remove the each on the display. If the password is correct:
Your radio proceeds to power up. See Powering Up the Radio on page 30 . OR If the password is incorrect:
The display shows Wrong Password. Repeat Step2. OR After the third incorrect password, the display shows Wrong Password and then shows Radio Locked. A tone sounds and the LED double blinks yellow. 31 English Non-Keypad Radio
1. Power up the radio. 2. You hear a continuous tone. 3. Use the Channel Selector Knob to enter the first digit of the password. 4. Press Side Button 1 or 2 to enter each digit of the remaining three digits of the password. You hear a positive indicator tone for each Side Button press. When the second digit of the password is entered, your radio ignores any Channel Selector Knob position change. 5. When the last digit of the four-digit password is entered, your radio automatically checks the valid-
ity of the password. If the password is correct:
Your radio proceeds to power up. See Powering Up the Radio on page 30. OR If the password is incorrect:
You hear a continuous tone. Repeat Steps 1 to 3. OR After the third incorrect password, your radio enters into locked state. A tone sounds and the LED double blinks yellow. Selecting a Zone Limited Keypad Radio
32 English A zone is a group of channels. The limited keypad radio supports up to 50 channels and 128 zones, with a maximum of 16 channels per zone. Use the following procedure to select a zone. Procedure:
Press the programmed Zone button and proceed to Step 3. OR Follow the procedure below. 1. c to access the menu. 2. < or > to Zone and press e to select. 3. The current zone is displayed and indicated by a
. 4. < or > to the required zone and press e to select. 5. The display shows <Zone> Selected momen-
tarily and returns to the selected zone screen. Non-Keypad Radio
The non keypad radio supports up to 16 channels and16 zones, with a maximum of 1 channel per zone. 1. Press the programmed Zone button. 2. You hear a positive indicator tone, indicating the radio has switched from Zone 1 to Zone 2. OR You hear a negative indicator tone, indicating the radio has switched from Zone 2 to Zone 1. 33 English Selecting a Radio Channel, Subscriber ID, or Group ID Once the required zone is displayed (if you have mul-
tiple zones in your radio), turn the programmed Chan-
nel Selector Knob to select the channel. Making a Group Call 1. Turn the Channel Selector Knob to select the channel with the active group alias or ID. 2. Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3. Press the PTT button to make the call. The LED lights up solid green. The first text line shows the group call icon. The second text line shows the group call alias, 4. Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone. 5. Release the PTT button to listen.When the target radio responds, the LED blinks green. You see the Group Call icon, the group alias or ID, and trans-
mitting radio alias or ID on your display. If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the 6. 34 English channel is free for you to respond. Press the PTT button to respond. OR If there is no voice activity for a predetermined period of time, the call ends. 7. Radio returns to the screen you were on prior to initiating the call. Making a Private Call 1. Turn the Channel Selector Knob to select the channel with the active subscriber alias or ID. 2. Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3. Press the PTT button to make the call. The LED lights up solid green. The first text line shows the private call icon. The second text line displays the private call alias. 4. Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. 5. Release the PTT button to listen. When the target radio responds, the LED blinks green. If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the tar-
get radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. OR 6. 35 English If there is no voice activity for a predetermined period of time, the call ends. 7. You hear a short tone. 8. The display shows Call Ended.**
NOTE:
Indicates a conventional Digital Mode-
Only feature.
**not applicable for Non-Keypad Radio. Making an All Call 1. Turn the Channel Selector Knob to select the channel with the active All Call group alias or ID. 2. Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3. Press the PTT button to make the call. The LED lights up solid green. The Group Call icon appears in the top right corner. The first text line shows All Call. 4. Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone. Users on the channel cannot respond to an All Call. 36 English Scanning Channels NOTE: This feature is not applicable in Capacity Plus. Press the programmed Scan button to turn scan on or off. During scan, the LED blinks yellow and the scan icon is displayed. Making a Call Alert Limited Keypad Radio
Press the programmed One Touch Access button and proceed to Step 5. OR Follow the procedure below. 1. c to access the menu. 1. < or > to Contacts and press e to select. 1. < or > to the required subscriber alias or ID and press e to select. 1. < or > to Call Alert and press e to select. 1. The display shows Call Alert and the subscriber alias or ID, indicating that the Call Alert has been sent. 1. The LED lights up solid green when your radio is sending the Call Alert. 37 English 1. If the Call Alert acknowledgement is received, the display shows positive mini notice. OR If the Call Alert acknowledgement is not received, the display shows negative mini notice. Non-Keypad Radio
1. Press the programmed One Touch Access but-
ton to make a Call Alert to the predefined ID. 2. The LED lights up solid green when your radio is sending the Call Alert. If the Call Alert acknowledgement is received, two chirps sound. OR If the Call Alert acknowledgement is not received, a low-pitch tone sounds. 3. Sending a Quick Text Message Limited Keypad Radio
Press the programmed Text Message button and proceed to Step 3. OR Follow the procedure below. 1. c to access the menu. 2. < or > to Messages and press e to select. 3. < or > to Quick Text and press e to select. 38 English 4. < or > to the required Quick Text and press e to select. 6. 5. < or > to the required alias or ID and press e to select. OR The display shows transitional mini notice, con-
firming your message is being sent. If the message is sent, a tone sounds and the dis-
play shows positive mini notice. OR If the message is not sent, a low tone sounds and the display shows negative mini notice. Non-Keypad Radio
You can send Quick Text messages, programmed by your dealer, via the programmable button. 1. Press the programmed One Touch Access but-
ton to send a predefined Quick Text message to a predefined ID. 2. The LED lights up solid green. 3. Two chirps indicate that the message is sent suc-
cessfully. OR A low-pitch tone indicates that the message can-
not be sent. 39 English Sending an Emergency Alarm NOTE:
If your radio is set to Silent, it will not display any audio or visual indicators during Emergency mode. 1. Press the programmed Emergency On button. 2. The display shows Tx Alarm and the destination alias. The LED lights up solid green and the Emer-
gency icon appears. OR The display shows Tx Telegram and the destination alias. The LED lights up solid green and the Emergency icon appears. 3. When an Emergency Alarm acknowledgment is received, the Emergency tone sounds and the LED blinks green. The display shows Alarm Sent. OR If your radio does not receive an Emergency Alarm acknowledgement, and after all retries have been exhausted, a tone sounds and the display shows Alarm Failed. 4. Radio exits the Emergency Alarm mode and returns to the Home screen. Indicates a conventional Analog mode-
only feature. NOTE:
40 English 41 English MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. 2011 Motorola Solutions, Inc. All rights reserved. Motorola Solutions, Inc. 1303 East Algonquin Road Schaumburg, IL 60196 U.S.A.
*68009511001*
68009511001-A
1 | User Manual/Guide | Users Manual | 4.13 MiB |
LKP_NAG-LACR.book Page i Tuesday, September 6, 2011 5:01 PM M MOTOTRBO XPRTM 3500/3550 Limited Keypad Portable User Guide 68009512001-A LKP_NAG-LACR.book Page ii Tuesday, September 6, 2011 5:01 PM LKP_NAG-LACR.book Page i Tuesday, September 6, 2011 5:01 PM Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola Solutions, Inc. Address: 1301 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A. Phone Number: 1-800-927-2744 Hereby declares that the product:
Model Name: XPR 3300/3350 conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital Device As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. D e c l a r a t i o n o f C o n f o r m i t y i English LKP_NAG-LACR.book Page ii Tuesday, September 6, 2011 5:01 PM Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. y t i m r o f n o C f o n o i t a r a l c e D ii English LKP_NAG-LACR.book Page 1 Tuesday, September 6, 2011 5:01 PM Contents This User Guide contains all information you need to use the MOTOTRBO XPR 3500/3550 Digital Portable Radios. Declaration of Conformity . i Important Safety Information . 5 Product Safety and RF Exposure Compliance . 5 Firmware Version . 5 Computer Software Copyrights . 6 Handling Precautions . 7 Notes . 8 How to Use This Guide . 1 What Your Dealer/System Administrator Can Tell You . 1 Charging the Battery . 2 Attaching the Battery . 2 Attaching the Antenna . 3 Attaching the Belt Clip . 3 Attaching the Universal Connector Cover (Dust Cover) 4 Attaching the Accessory Connector . 4 Powering Up the Radio . 5 Adjusting the Volume . 6 Radio Controls . 6 Programmable Buttons . 7 Assignable Radio Functions . 8 Assignable Settings or Utility Functions . 9 Accessing the Programmed Functions . 9 Push-To-Talk (PTT) Button . 10 Switching Between Conventional Analog and Digital Mode . 11 Capacity Plus . 11 Display Icons . 12 Call Icons . 13 Advanced Menu Icons . 13 Mini Notice Icons . 14 LED Indicator . 14 Audio Tones . 15 Indicator Tones . 16 Making and Receiving Calls . 16 Selecting a Site . 16 Selecting a Zone . 17 Selecting a Radio Channel, Subscriber ID, or Group ID . 17 Receiving and Responding to a Radio Call . 18 Receiving and Responding to a Group Call . 18 Receiving and Responding to a Private Call . 19 Receiving an All Call . 20 1 English LKP_NAG-LACR.book Page 2 Tuesday, September 6, 2011 5:01 PM Receiving and Responding to a Selective Call . 21 Making a Radio Call . 22 Making a Call with the Channel Selector Knob . 22 Making a Selective Call . 24 Making a Call with the One Touch Access Button . 25 Stopping a Radio Call . 26 Talkaround . 26 Monitoring Features . 27 Monitoring a Channel . 27 Permanent Monitor . 27 Radio Check . 28 Sending a Radio Check . 28 Scan Lists . 29 Viewing an Entry in the Scan List . 29 Editing the Scan List . 30 Scan . 31 Starting and Stopping Scan . 32 Responding to a Transmission During a Scan . 32 Deleting a Nuisance Channel . 33 Restoring a Nuisance Channel . 33 Vote Scan . 34 Contacts Settings . 34 Making a Group Call from Contacts . 35 Making a Private Call from Contacts . 36 2 English Setting Default Contact . 36 Call Indicator Settings . 37 Activating and Deactivating Call Ringers for Call Alert 37 Activating and Deactivating Call Ringers for Private Calls . 37 Activating and Deactivating Call Ringers for Selective Call . 38 Activating and Deactivating Call Ringers for Text Message . 38 Assigning Ring Styles . 39 Escalating Alarm Tone Volume . 39 Call Log Features . 40 Viewing Recent Calls . 40 Deleting a Call from a Call List . 40 Call Alert Operation . 41 Receiving and Responding to a Call Alert . 41 Making a Call Alert from the Contacts List . 42 Making a Call Alert with the One Touch Access Button 42 Emergency Operation . 43 Sending an Emergency Alarm . 44 Sending an Emergency Alarm with Call . 44 Sending an Emergency Alarm with Voice to Follow . 45 Reinitiating an Emergency Mode . 46 LKP_NAG-LACR.book Page 3 Tuesday, September 6, 2011 5:01 PM Exiting Emergency Mode . 46 Analog Message Encode . 49 Sending MDC Message Encode to Dispatcher . 49 Analog Status Update . 49 Sending Status Update to Predefined Contact . 49 Privacy . 50 Dual Tone Multi Frequency (DTMF) . 51 IP Site Connect . 51 Starting an Automatic Site Search . 52 Stopping an Automatic Site Search . 53 Starting a Manual Site Search . 53 Security . 54 Radio Disable . 54 Radio Enable . 55 Lone Worker . 56 Password Lock Features . 57 Accessing the Radio from Password . 57 Unlocking the Radio from Locked State . 57 Turning the Password Lock On or Off . 58 Changing the Password . 58 Notification List . 59 Accessing the Notification List . 59 Utilities . 60 Turning the Radio Tones/Alerts On or Off . 60 Setting the Tone Alert Volume Offset Level . 60 Turning the Talk Permit Tone On or Off . 61 Setting the Power Level . 61 Adjusting the Display Brightness . 62 Controlling the Display Backlight . 62 Setting the Squelch Level . 63 Turning the Introduction Screen On or Off . 63
. 63 Language . 64 Turning the LED Indicator On or Off . 64 Turning the Voice Operating Transmission (VOX) Feature On or Off . 64 Voice Announcement . 65 Call Forwarding . 66 Menu Timer . 67 Analog Mic AGC . 67 Digital Mic AGC . 68 Intelligent Audio . 68 Accessing General Radio Information . 69 Front Panel Configuration (FPC) . 70 Entering FPC Mode . 70 Editing FPC Mode Parameters . 70 Accessories . 71 Antennas . 71 Batteries . 71 Cables . 72 3 English LKP_NAG-LACR.book Page 4 Tuesday, September 6, 2011 5:01 PM Carry Devices . 72 Chargers . 72 Earbuds and Earpieces . 73 Headsets and Headset Accessories . 73 Remote Speaker Microphones . 73 Surveillance Accessories . 73 Miscellaneous Accessories . 74 Batteries and Chargers Warranty . 75 Limited Warranty . 76 4 English LKP_NAG-LACR.book Page 5 Tuesday, September 6, 2011 5:01 PM Important Safety Information Product Safety and RF Exposure Compliance Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION!
This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio
(Motorola Publication part number 6881095C98) to ensure compliance with RF energy exposure limits. For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website:
http://www.motorolasolutions.com/governmentandenterprise Firmware Version All the features described in the following sections are supported by the radio's software version R02.00.00. See Checking the Firmware Version and Codeplug Version and Codeplug Version on page 70 to determine your radio's software version. Check with your dealer or system administrator for more details of all the features supported. I m p o r t a n t S a f e t y I n f o r m a t i o n 5 English The AMBE+2TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Pat. Nos. #5,870,405, #5,826,222, #5,754,974,
#5,701,390, #5,715,365, #5,649,050, #5,630,011,
#5,581,656, #5,517,511, #5,491,772, #5,247,579,
#5,226,084 and #5,195,166. LKP_NAG-LACR.book Page 6 Tuesday, September 6, 2011 5:01 PM Computer Software Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. s t h g i r y p o C e r a w t f o S r e t u p m o C 6 English LKP_NAG-LACR.book Page 7 Tuesday, September 6, 2011 5:01 PM Handling Precautions The Andorra Portables radio meets IP55 specifications with antenna attached, allowing the radio to withstand adverse field conditions such as being used in rain or dusty environment. If the radio has been exposed to water or rain, shake the radio well to remove any water that may be trapped inside the speaker grille, microphone port and aesthetic cover(if applicable). Trapped water in speaker grille and microphone port could cause decreased audio performance. If aesthetic cover is attached onto radio, trapped water in aesthetic cover could cause corrosion on the slim connector interface gold contacts. If the radios battery contact area has been exposed to water, clean and dry battery contacts on both the radio and the battery before attaching the battery to the radio. The residual water could short-circuit the radio. If the radio has been exposed to corrosive substance
(e.g.saltwater), rinse the radio and battery in fresh water then dry the radio and battery. To clean the exterior surfaces of the radio, use a diluted solution of mild dishwashing detergent and fresh water (i.e. one teaspoon of detergent to one gallon of water). The radio with antenna attached properly is designed to be protected against dust and low pressure jets of water projected with nozzle 6.3mm diameter at flow rate of 12.5 l/
min, with water pressure at 30 kN/m2 and from a distance of 2.5m to 3m for at least 3 min. Exceeding either maximum limit or use without antenna may result in damage to the radio. When cleaning the radio, do not use a high pressure jet spray on the radio as this may cause to leak. Do not disassemble the radio. This could damage radio seals and result in leak paths into the radio. Radio maintenance should only be done in service depot that is equipped to test and replace the seal on the radio. H a n d l i n g P r e c a u t i o n s 7 English LKP_NAG-LACR.book Page 8 Tuesday, September 6, 2011 5:01 PM Notes s e t o N 8 English LKP_NAG-LACR.book Page 1 Tuesday, September 6, 2011 5:01 PM How to Use This Guide This User Guide covers the basic operation of the MOTOTRBO Portables. However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information. Throughout this publication, the icons below are used to indicate features supported in either the conventional Analog mode or conventional Digital mode:
Indicates a conventional Analog Mode-Only feature. Indicates a conventional Digital Mode-Only feature. For features that are available in both conventional Analog and Digital modes, no icon is shown. Selected features are also available on the single-site trunking mode, Capacity Plus. See Capacity Plus on page 11 for more information. What Your Dealer/System Administrator Can Tell You You can consult your dealer or system administrator about the following:
Is your radio programmed with any preset conventional channels?
Which buttons have been programmed to access other features?
What optional accessories may suit your needs?
NOTE:
1 English LKP_NAG-LACR.book Page 2 Tuesday, September 6, 2011 5:01 PM Charging the Battery Attaching the Battery Your radio is powered by a Nickel Metal-Hydride (NiMH) or Lithium-Ion (Li-lon) battery. To avoid damage and comply with warranty terms, charge the battery using a Motorola charger exactly as described in the charger user guide. Charge a new battery 14 to 16 hours before initial use for best performance. IMPORTANT: ALWAYS charge your IMPRES battery with an IMPRES charger for optimized battery life and valuable battery data. IMPRES batteries charged exclusively with IMPRES chargers receive a 6-month capacity warranty extension over the standard Motorola Premium battery warranty duration. 2 English Align the battery with the rails on the back of the radio. Press the battery firmly, and slide upward until the latch snaps into place. Slide battery latch into lock position. To remove the battery, turn the radio off. Move the battery latch into unlock position and hold, and slide the battery down and off the rails. Battery Latch LKP_NAG-LACR.book Page 3 Tuesday, September 6, 2011 5:01 PM Attaching the Antenna Attaching the Belt Clip With the radio turned off, set the antenna in its receptacle and turn clockwise. Align the grooves on the clip with those on the battery and press downward until you hear a click. To remove the clip, press the belt clip tab away from the battery using a key. Then slide the clip upward and away from the radio. To remove the antenna, turn the antenna counterclockwise. If antenna needs to be replaced, ensure that only MOTOTRBO antennas are used. Neglecting this will damage your radio. See Antennas on page 71 for a list of available antennas. 3 English LKP_NAG-LACR.book Page 4 Tuesday, September 6, 2011 5:01 PM Attaching the Universal Connector Cover
(Dust Cover) The universal connector is located on the antenna side of the radio. It is used to connect MOTOTRBO accessories to the radio. Insert the hooked end of the cover into the slots above the universal connector. Press downward on the cover to seat the lower tab properly into the RF connector. Turn the thumbscrew clockwise to secure the Universal Connector connector cover to the radio. To remove the universal connector cover, press down on the cover and turn the thumbscrew counterclockwise. Lift the cover up, slide the connector cover loop upwards, and remove it from the attached antenna. Replace the dust cover when the universal connector is not in use. 4 English Attaching the Accessory Connector The accessory connector is to be secured to the universal connector on the antenna side of the radio. To attach the accessory connector, refer to the steps shown in the diagram. To remove the accessory connector, refer to the steps shown in the diagram. 1 2 3 3 2 1 LKP_NAG-LACR.book Page 5 Tuesday, September 6, 2011 5:01 PM Powering Up the Radio Rotate the On/Off/Volume Control Knob clockwise until you hear a click. You see MOTOTRBO (TM) on the radios display momentarily, followed by a welcome message. The LED lights up solid green and the Home screen lights up if the backlight setting is set to turn on automatically. LED Indicator NOTE: The Home screen does not light up during a power up if the LED indicator is disabled (see Turning the LED Indicator On or Off on page 64 ). A brief tone sounds, indicating that the power up test is successful. NOTE: There is no power up tone if the radio tones/alerts function is disabled (see Turning the Radio Tones/
Alerts On or Off on page 60). If your radio does not power up, check your battery. Make sure that it is charged and properly attached. If your radio still does not power up, contact your dealer. To turn off the radio, rotate this knob counterclockwise until you hear a click. You see a brief Powering Down on the radios display. 5 English LKP_NAG-LACR.book Page 6 Tuesday, September 6, 2011 5:01 PM Adjusting the Volume Radio Controls To increase the volume, turn the On/Off/Volume Control Knob clockwise. To decrease the volume, turn this knob counterclockwise. NOTE: Your radio can be programmed to have a minimum volume offset where the volume level cannot be turned down fully. Check with your dealer or system administrator for more information. 6 English 1 2 3 4 5 6 7 8 9 10 18 17 16 15 14 13 12 11 1 2 3 Channel Selector Knob On/Off/Volume Control Knob LED Indicator LKP_NAG-LACR.book Page 7 Tuesday, September 6, 2011 5:01 PM 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Push-to-Talk (PTT) Button Microphone Side Button 1*
Side Button 2*
Left Navigation Button Menu Button Front Button P1*
OK Button Front Button P2*
Back/Home Button Right Navigation Button Display Speaker Universal Connector for Accessories Antenna
* These buttons are programmable. Programmable Buttons Your dealer can program the programmable buttons as shortcuts to radio functions or preset channels/groups depending on the duration of a button press:
Short press Pressing and releasing rapidly. Long press Pressing and holding for the programmed duration. Hold down Keeping the button pressed. NOTE: The programmed duration of a button press is applicable for all assignable radio/utility functions or settings. See Emergency Operation on page 43 for more information on the programmed duration of the Emergency button. 7 English LKP_NAG-LACR.book Page 8 Tuesday, September 6, 2011 5:01 PM Assignable Radio Functions
Contacts Provides direct access to the Contacts list. Call Alert Direct acces to the radio contacts list to select aradio contact to send a call alert to. Call Forwarding Toggles Call Forwarding on or off. Call Log Selects the call log list. Channel Announcment Plays zone and channel announcement voice messages for the current channel. Emergency Depending on the programming, initiates or cancels an emergency alarm or call. Intelligent Audio On/Off Toggles intelligent Audio on or off. Starts the manual site search. Manual Site Roam*
Mic AGC On/Off Toggles the internal microphone automatic gain control (AGC) on or off. Monitor Monitors a selected channel for activity. Nuisance Channel Delete* Temporarily removes an unwanted channel, except for the Selected Channel, from the scan list. The Selected Channel refers to the users selected zone/channel combination from which scan is initiated. One Touch Access Private or Group Call, a Call Alert or a Quick Text message. Directly initiates a predefined 8 English Permanent Monitor* Monitors a selected channel for all radio traffic until function is disabled. Toggles privacy on or off. Privacy Radio Alias and ID Provides radio alias and ID. Radio Check Determines if a radio is active in a system. Radio Enable enabled. Allows a target radio to be remotely Allows a target radio to be remotely Radio Disable disabled. Repeater/Talkaround* Toggles between using a repeater and communicating directly with another radio. Scan* Toggles scan on or off. Site Lock On/Off*
off. Toggles the automatic site roam on or Transmit Interrupt Remote Dekey transmission of a remote monitored radio without giving any indicators, or an ongoing interruptible call to free the channel. Stops the Selects the text message menu. Text Message Voice Announcement On/Off Toggles Voice Announcement on or off.
* Not applicable in Capacity Plus LKP_NAG-LACR.book Page 9 Tuesday, September 6, 2011 5:01 PM Voice Operating Transmission (VOX) Toggles VOX on or off. Zone Allows selection from a list of zones.
Assignable Settings or Utility Functions All Tones/Alerts Toggles all tones and alerts on or off. Backlight Toggles display backlight on or off. Backlight brightness Adjusts the brightness level. Power Level Toggles transmit power level between high and low. Squelch normal. Toggles squelch level between tight and Accessing the Programmed Functions You can access various radio functions through one of the following ways:
A short or long press of the relevant programmable buttons. OR
ce >
d Use the Menu Navigation Buttons as follows:
1 To access the menu, press the c button. Press the appropriate Menu Scroll button (<or >) to access the menu functions. 2 To select a function or enter a sub-menu, press the e button. 3 To go back one menu level, or to return to the previous screen, press the d button. Long press the d button to return to the Home screen. NOTE: Your radio automatically exits the menu after a period of inactivity and returns to your Home screen.
* Not applicable in Capacity Plus 9 English LKP_NAG-LACR.book Page 10 Tuesday, September 6, 2011 5:01 PM Push-To-Talk (PTT) Button The PTT button on the side of the radio serves two basic purposes:
PTT Button While a call is in progress, the PTT button allows the radio to transmit to other radios in the call. Press and hold down PTT button to talk. Release the PTT button to listen. The microphone is activated when the PTT button is pressed. 10 English While a call is not in progress, the PTT button is used to make a new call (see Making a Radio Call on page 22). If the Talk Permit Tone (see Turning the Talk Permit Tone On or Off on page 61) or the PTT Sidetone until the short alert tone ends before talking. is enabled, wait During a call, if the Channel Free Indication feature is enabled on your radio (programmed by your dealer), you will hear a short alert tone the moment the target radio (the radio that is receiving your call) releases the PTT button, indicating the channel is free for you to respond. You will also hear the Channel Free Indication tone if your call is interrupted, for example when the radio receives an Emergency Call. You can turn off the Channel Free Indication tone or the PTT Sidetone by disabling all radio tones and alerts
(see Turning the Radio Tones/Alerts On or Off on page 60). LKP_NAG-LACR.book Page 11 Tuesday, September 6, 2011 5:01 PM Switching Between Conventional Analog and Digital Mode Each channel in your radio can be configured as a conventional analog or conventional digital channel. Use the Channel Selector Knob to switch between an analog or a digital channel. Channel Selector Knob When switching from digital to analog mode, certain features are unavailable. Icons for the digital features (such as Messages) reflect this change by appearing grayed out. Disabled features are hidden in the menu. Your radio also has features available in both analog and digital mode. However, the minor differences in the way each feature works does NOT affect the performance of your radio. NOTE: Your radio also switches between digital and analog modes during a dual mode scan (see Scan on page 31). Capacity Plus Capacity Plus is a single-site trunking configuration of the MOTOTRBO radio system, which uses a pool of channels to support hundreds of users and up to 254 Groups. This feature allows your radio to efficiently utilize the available number of programmed channels while in Repeater Mode. You can only access channel(s) with Capacity Plus via the Channel Selector Knob, while features supported in Capacity Plus can be accessed via the menu and/or a programmable button press. Icons of features not applicable to Capacity Plus will not be available in the menu. You will hear a negative indicator tone if you access a feature not applicable to Capacity Plus via a programmable button press. Your radio also has features that are available in both conventional digital mode and Capacity Plus. However, the minor differences in the way each feature works does NOT affect the performance of your radio. A Software License Key sold separately is required for this feature. Check with your dealer or system administrator for more information on this system. 11 English LKP_NAG-LACR.book Page 12 Tuesday, September 6, 2011 5:01 PM Display Icons The 132 x 36 pixels, monochrome display, liquid crystal display
(LCD) of your radio shows radio status, text entries, and menu entries. The following are icons that appear on the status bar at the top of the radios display. Icons are displayed on the status bar, arranged left-to-right, in order of appearance/usage. Received Signal Strength Indicator (RSSI) The number of bars displated represents the radio signal strength. Four bars indicate the strongest signal. The icon is only displayed while receiving. Battery The number of bars (0 4) shown indicates the charge remaining in the battery. Blinks when the battery is low. Emergency Radio is in emergency mode. Notification Notification list is not empty. Scan*
Scan feature is enabled. Scan Priority 1*
Radio detects activity on channel/group designated as Priority 1 12 English Scan Priority 2*
Radio detects activity on channel/group designated as Priority 2. Vote Scan Vote scan feature is enabled. Monitor Selected channel is being monitored. Talkaround*
In the absence of a repeater, radio is currently configured for direct radio to radio communication. Site Roaming*
The site roaming feature is enabled. Secure The Privacy feature is enabled. Unsecure The Privacy feature disabled. Tones Disabled Tones are turned off. Power Level Radio is set at Low Power Radio is set at High Power OR LKP_NAG-LACR.book Page 13 Tuesday, September 6, 2011 5:01 PM Call Icons Advanced Menu Icons The following icons appear on the radios display during a call. These icons also appear in the Contacts list to indicate ID type. Private Call Indicates a Private Call in progress. In the Contacts list, it indicates a subscriber alias (name) or ID
(number). Group Call/All Call Indicates a Group Call or All Call in progress. In the Contacts list, it indicates a group alias (name) or ID
(number) The following icons appear beside menu items that offer a choice between two options or as an indication that there is a sub-menu offering two options. Checkbox (Empty) Indicates the option is not selected. Checkbox (Checked) Indicates the option is selected. Solid Black Box Indicates the option selected for the menu item with a sub-menu. 13 English LKP_NAG-LACR.book Page 14 Tuesday, September 6, 2011 5:01 PM Mini Notice Icons LED Indicator The following icons appear momentarily on the radios display after an action to perform task is take. The LED indicator shows the operational status of your radio. Successful Transmission (Positive) Successful action taken. Failed Transmission (Negative) Failed action taken. Transmission in Progress (Transitional) Transmitting. This dynamic icon is seen before indication for Successful Transmission or Failed Transmission. LED Indicator 14 English Blinking red Radio is transmitting at low battery condition, receiving an emergency transmission or has failed the self-test upon powering up. Solid yellow Radio is monitoring a conventional channel. Blinking yellow Radio is scanning for activity or receiving a Call Alert. LKP_NAG-LACR.book Page 15 Tuesday, September 6, 2011 5:01 PM Double blinking yellow Radio is no longer connected to the repeater while in Capacity Plus, all Capacity Plus channels are currently busy. Auto roaming is enabled, radio is actively searching for a new site. Also indicates radio has yet to respond to a group call alert, or radio is locked. Solid green Radio is powering up, or transmitting. Blinking green Radio is receiving a non-privacy-enabled call or data, or detecting activity over the air. Double blinking green Radio is receiving a privacy-enabled call or data. NOTE: While in conventional mode, when the LED blinks green, it indicates the radio detects activity over the air. Due to the nature of the digital protocol, this activity may or may not affect the radio's programmed channel. For Capacity Plus, there is no LED indication when the radio is detecting activity over the air. Audio Tones Alert tones provide you with audible indications of the radios status or the radios response to data received. Continuous Tone A monotone sound. Sounds continuously until termination. Periodic Tone Sounds periodically depending on the duration set by the radio. Tone starts, stops, and repeats itself. Repetitive Tone A single tone that repeats itself until it is terminated by the user. Momentary Tone Sounds only once for a short period of time defined by the radio.
* Not applicable in Capacity Plus 15 English LKP_NAG-LACR.book Page 16 Tuesday, September 6, 2011 5:01 PM Indicator Tones High pitched tone Low pitched tone OR s l l Positive Indicator Tone Negative Indicator Tone a C g n v i i Making and Receiving Calls Once you understand how your MOTOTRBO Portable is configured, you are ready to use your radio. Selecting a Site A site is a specific area where a base station is placed to provide optimal coverage for the radio. If enabled, your radio is able to connect to different available sites via an Internet Protocol (IP) network. See IP Site Connect on page 51 for more information. e c e R d n a g n k a M i 16 English LKP_NAG-LACR.book Page 17 Tuesday, September 6, 2011 5:01 PM Selecting a Zone A zone is a group of channels. Your radio supports up to 128 channels and 50 zones, with a maximum of 16 channels per zone. Use the following procedure to select a zone. Procedure:
Press the programmed Zone button and proceed to Step 3. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Zone and press e to select. 3 The current zone is displayed and indicated by a . 4 < or > to the required zone and press e to select. 5 The display shows <Zone> Selected momentarily and returns to the selected zone screen. Selecting a Radio Channel, Subscriber ID, or Group ID Procedure:
Once the required zone is displayed (if you have multiple zones in your radio), turn the programmed Channel Selector Knob to select the channel. i M a k n g a n d R e c e i i v n g C a l l s 17 English LKP_NAG-LACR.book Page 18 Tuesday, September 6, 2011 5:01 PM Receiving and Responding to a Radio Call LED Indicator Once the channel, subscriber ID or group ID is displayed, you can proceed to receive and respond to calls. The LED lights up solid green while the radio is transmitting and blinks green when the radio is receiving. NOTE: The LED lights up solid green while the radio is transmitting and double blinks green when the radio is receiving a privacy-enabled call. To unscramble a privacy-enabled call, your radio must have the same Privacy Key, OR the same Key Value and Key ID (programmed by your dealer), as the transmitting radio (the radio you are receiving the call from). See Privacy on page 50 for more information. Receiving and Responding to a Group Call
To receive a call from a group of users, your radio must be configured as part of that group. Procedure:
When you receive a Group Call (while on the Home screen):
1 The LED blinks green. 2 The Group Call icon appears in the top right corner. The first text line shows the caller alias. The second text line displays the group call alias.. 3 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 4 If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond to the call. OR If the Voice Interrupt feature is enabled, press the PTT button to stop the current call from the transmitting radio and free the channel for you to talk/respond. s l l a C g n v i i e c e R d n a g n k a M i 18 English LKP_NAG-LACR.book Page 19 Tuesday, September 6, 2011 5:01 PM 5 The LED lights up solid green. 6 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone. 7 Release the PTT button to listen. 8 If there is no voice activity for a predetermined period of time, the call ends. See Making a Group Call on page 22 for details on making a Group Call. NOTE:
If the radio receives a Group Call while not on the Home screen, it remains on its current screen prior to answering the call. Receiving and Responding to a Private Call
A Private Call is a call from an individual radio to another individual radio. There are two types of Private Calls. The first type, where a radio presence check is performed prior to setting up the call, while the other sets up the call immediately. When your radio is checked, the LED blinks green. Only one of these call types can be programmed to your radio by your dealer. Procedure:
When you receive a Private Call:
1 The LED blinks green. 2 The first text line shows private call icon. The second text line displays the private call alias. Long press the d button to go to the Home screen to view the caller alias before replying. 3 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. i M a k n g a n d R e c e i i v n g C a l l s 19 English LKP_NAG-LACR.book Page 20 Tuesday, September 6, 2011 5:01 PM 4 If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond to the call. OR If the Voice Interrupt feature is enabled, press the PTT button to stop the current call from the transmitting radio and free the channel for you to talk/respond. 5 The LED lights up solid green. 6 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. 7 Release the PTT button to listen. 8 If there is no voice activity for a predetermined period of time, the call ends. 9 You hear a short tone. The display shows Call Ended. See Making a Private Call on page 23 for details on making a Private Call. s l l a C g n v i i e c e R d n a g n k a M i 20 English Receiving an All Call
An All Call is a call from an individual radio to every radio on the channel. It is used to make important announcements requiring the users full attention. Procedure:
When you receive an All Call:
1 A tone sounds and the LED blinks green. 2 The Group Call icon appears in the top right corner. The first text line shows the caller alias. The second text line displays All Call. 3 Once the All Call ends, the radio returns to the previous screen before receiving the call. If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is now available for use. You cannot respond to an All Call. See Making an All Call on page 23 for details on making an All Call. NOTE: The radio stops receiving the All Call if you switch to a different channel while receiving the call. During an All Call, you will not be able to use any programmed button functions until the call ends. LKP_NAG-LACR.book Page 21 Tuesday, September 6, 2011 5:01 PM
Receiving and Responding to a Selective Call A Selective Call is a call from an individual radio to another individual radio. It is a Private Call on an analog system. Procedure:
When you receive a Selective Call:
1 The LED blinks green. 2 The Private Call icon appears in the top right corner. The first text line shows the caller alias or Selective Call or Alert with Call. 3 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 4 If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond to the call. 5 The LED lights up solid green. 6 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. 7 Release the PTT button to listen. 8 If there is no voice activity for a predetermined period of time, the call ends. You hear a short tone. The display shows Call Ended. NOTE: See Making a Selective Call on page 24 for details on making a Private Call. i M a k n g a n d R e c e i i v n g C a l l s 21 English LKP_NAG-LACR.book Page 22 Tuesday, September 6, 2011 5:01 PM Making a Radio Call You can select a channel, subscriber ID, or group by using:
The Channel Selector Knob A programmed One Touch Access button A programmable button This method is for Phone Calls only. The Contacts list (see Contacts Settings on page 34) NOTE: Your radio must have the Privacy feature enabled on the channel to send a privacy-enabled transmission. Only target radios with the same Privacy Key OR the same Key Value and Key ID as your radio will be able to unscramble the transmission. See Privacy on page 50 for more information.
Making a Call with the Channel Selector Knob Making a Group Call
To make a call to a group of users, your radio must be configured as part of that group. Procedure:
1 Turn the Channel Selector Knob to select the channel with the active group alias or ID. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to make the call. The LED lights up solid green. The first text line shows the group call icon. The second text line shows the group call alias, 4 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone. 5 Release the PTT button to listen.When the target radio responds, the LED blinks green. You see the Group Call icon, the group alias or ID, and transmitting radio alias or ID on your display. 6 If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. OR If there is no voice activity for a predetermined period of time, the call ends. s l l a C g n v i i e c e R d n a g n k a M i 22 English LKP_NAG-LACR.book Page 23 Tuesday, September 6, 2011 5:01 PM 7 Radio returns to the screen you were on prior to initiating the call. You can also make a Group Call via Contacts (see Making a Group Call from Contacts on page 35). Making a Private Call
While you can receive and/or respond to a Private Call initiated by an authorized individual radio, your radio must be programmed for you to initiate a Private Call. You will hear a negative indicator tone, when you make a Private Call via the Contacts list, Call Log, One Touch Access button, the programmed number keys, or the Channel Selector Knob, if this feature is not enabled. Use the Text Message or Call Alert features to contact an individual radio. See Call Alert Operation on page 41 for more information. Procedure:
1 Turn the Channel Selector Knob to select the channel with the active subscriber alias or ID. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to make the call. The LED lights up solid green. The first text line shows the private call icon. The second text line displays the private call alias. 4 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. 5 Release the PTT button to listen. When the target radio responds, the LED blinks green. 6 If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. OR If there is no voice activity for a predetermined period of time, the call ends. 7 You hear a short tone. The display shows Call Ended. You can also make a Private Call via Contacts (see Making a Private Call from Contacts on page 36) . Making an All Call
This feature allows you to transmit to all users on the channel. Your radio must be programmed to allow you to use this feature. Procedure:
1 Turn the Channel Selector Knob to select the channel with the active All Call group alias or ID. i M a k n g a n d R e c e i i v n g C a l l s 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 23 English Permit Tone to finish (if enabled) and speak clearly into the microphone. OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone. 4 Release the PTT button to listen. When the target radio responds, the LED blinks green. 5 If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. OR If there is no voice activity for a predetermined period of time, the call ends. 6 You hear a short tone. The display shows Call Ended. LKP_NAG-LACR.book Page 24 Tuesday, September 6, 2011 5:01 PM 3 Press the PTT button to make the call. The LED lights up solid green. The first text line shows the All Call icon. The second text line displays the All Call alias. 4 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone. Users on the channel cannot respond to an All Call. s l l a C g n v i i e c e R d n a g n k a M i Making a Selective Call
Just like a Private Call, while you can receive and/or respond to a Selective Call initiated by an authorized individual radio, your radio must be programmed for you to initiate a Selective Call. Procedure:
1 Turn the Channel Selector Knob to select the channel with the active subscriber alias or ID. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to make the call. The LED lights up solid green. The Private Call icon appears in the top right corner. The first text line shows the subscriber alias. The second text line displays the call status. Wait for the Talk 24 English LKP_NAG-LACR.book Page 25 Tuesday, September 6, 2011 5:01 PM
Making a Call with the One Touch Access Button The One Touch Access feature allows you to make a Group, Private or Phone Call to a predefined alias or ID easily. This feature can be assigned to a short or long programmable button press. You can ONLY have one alias or ID assigned to a One Touch Access button. Your radio can have multiple One Touch Access buttons programmed. Procedure:
1 Press the programmed One Touch Access button to make a Group or Private Call to the predefined alias or ID. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to make the call. The LED lights up solid green. The Group/Private Call icon appears in the top right corner. The first text line shows the caller alias. The second text line displays the call status for a Private Call. 4 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. 5 Release the PTT button to listen. When the target radio responds, the LED blinks green. 6 If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. OR If there is no voice activity for a predetermined period of time, the call ends. 7 Radio returns to the screen you were on prior to initiating the call. For a Private Call, you hear a short tone when the call ends. i M a k n g a n d R e c e i i v n g C a l l s 25 English LKP_NAG-LACR.book Page 26 Tuesday, September 6, 2011 5:01 PM Stopping a Radio Call Talkaround This feature allows you to stop an ongoing Group or Private Call to free the channel for transmission. For example, when a radio experiences a stuck microphone condition where the PTT button is inadvertently pressed by the user. Your radio must be programmed to allow you to use this feature. Procedure:
While on the required channel:
1 Press the programmed Transmit Interrupt Remote Dekey button. 2 The display shows Remote Dekey. 3 Wait for acknowledgment. 4 The radio sounds a positive indicator tone and the display shows Remote Dekey Success, indicating that the channel is now free. OR The radio sounds a negative indicator tone and the display shows Remote Dekey Failed. On the interrupted radio, the display shows Call Interrupted, and the radio sounds a negative indicator tone until you release the PTT button, if it is transmitting an interruptible call that is stopped via this feature. s l l a C g n v i i e c e R d n a g n k a M i 26 English You can continue to communicate when your repeater is not operating, or when your radio is out of the repeaters range but within talking range of other radios. This is called talkaround. NOTE: This feature is not applicable in Capacity Plus. Procedure:
Press the programmed Repeater/Talkaround button to toggle between talkaround and repeater modes. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 Press e to enable Talkaround. The display shows beside Enabled. OR Press e to disable Talkaround. The disappears from beside Enabled. 5 The screen automatically returns to the previous menu. The Talkaround setting is retained even after powering down LKP_NAG-LACR.book Page 27 Tuesday, September 6, 2011 5:01 PM NOTE: At Step 4, you can also use < or > to change the selected option. Monitoring Features Monitoring a Channel
Use the Monitor feature to make sure a channel is clear before transmitting. NOTE: This feature is not applicable in Capacity Plus. Procedure:
1 Press and hold the programmed Monitor button and listen for activity. 2 The Monitor icon appears on the status bar and the LED lights up solid yellow. 3 You hear radio activity or total silence, depending on how your radio is programmed. 4 When you hear white noise (that is, the channel is free), press the PTT button to talk and release it to listen. Permanent Monitor
Use the Permanent Monitor feature to continuously monitor a selected channel for activity. NOTE: This feature is not applicable in Capacity Plus. Procedure:
1 Press the programmed Permanent Monitor button. 2 Radio sounds an alert tone, the LED lights up solid yellow, and the display shows Permanent Monitor On. The Monitor icon appears on the status bar. 3 Press the programmed Permanent Monitor button to exit Permanent Monitor mode. 4 Radio sounds an alert tone, the LED turns off, and display shows Permanent Monitor Off. i M a k n g a n d R e c e i i v n g C a l l s 27 English LKP_NAG-LACR.book Page 28 Tuesday, September 6, 2011 5:01 PM Radio Check If enabled, this feature allows you to determine if another radio is active in a system without disturbing the user of that radio. No audible or visual notification is shown on the target radio. This feature is only applicable for subscriber aliases or IDs. Sending a Radio Check
Procedure:
Use the programmed Radio Check button. 1 Press the programmed Radio Check button. 2 < or > to the required subscriber alias or ID and press e to select. 3 The display shows transitional mini notice, indicating the request is in progress. The LED lights up solid green. 4 Wait for acknowledgement. 28 English 5 If successful, a positive indicator tone sounds and the display shows positive mini notice. OR If unsuccessful, a negative indicator tone sounds and the display shows negative mini notice. 6 Radio returns to the subscriber alias or ID screen. OR Procedure:
Use the menu. 1 c to access the menu. 2 < or > to Contacts and press e to select. 3 < or > to the required subscriber alias or ID and press e to select. 4 < or > to Radio Check and press e to select. 5 The display shows transitional mini notice, indicating the request is in progress. The LED lights up solid green. 6 Wait for acknowledgement. 7 If successful, a positive indicator tone sounds and the display shows positive mini notice. OR If unsuccessful, a negative indicator tone sounds and the display shows negative mini notice. LKP_NAG-LACR.book Page 29 Tuesday, September 6, 2011 5:01 PM 8 Radio returns to the subscriber alias or ID screen. If the d button is pressed when the radio is waiting for acknowledgement, a tone sounds, and the radio terminates all retries and exits Radio Check mode. Scan Lists Scan lists are created and assigned to individual channels/
groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group. Your radio can support up to 250 scan lists, with a maximum of 16 members in a list. Each scan list supports a mixture of both analog and digital entries. You can add, delete, or prioritize channels by editing a scan list. You can attach a new scan list to your radio via Front Panel Programming. NOTE: This feature is not applicable in Capacity Plus. Viewing an Entry in the Scan List
Procedure:
1 c to access the menu. 2 < or > to Scan and press e to select. 3 < or > to Scan List and press e to select. 4 Use < or > to view each member on the list. The priority icon appears left of the members alias, if set, to indicate whether the member is on a Priority 1 or Priority 2 29 English LKP_NAG-LACR.book Page 30 Tuesday, September 6, 2011 5:01 PM channel list. You cannot have multiple Priority 1 or Priority 2 channels in a scan list. There is no priority icon if priority is set to None.
Editing the Scan List Adding a New Entry to the Scan List
Procedure:
1 c to access the menu. 2 < or > to Scan and press e to select. 3 < or > to Scan List and press e to select. 4 < or > to Add Member and press e to select. 5 < or > to the required alias or ID. 6 < or > to the required priority level and press e to select. 7 The display shows positive mini notice, followed immediately by Add Another?. 8 < or > to Yes and press e to select, to add another entry, and repeat Steps 5 to 8. OR 30 English
< or > to No and press e to select to save the current list. Deleting an Entry from the Scan List
Procedure:
1 c to access the menu. 2 < or > to Scan and press e to select. 3 < or > to Scan List and press e to select. 4 < or > to the required alias or ID. 5 Press e to select. 6 < or > to Delete and press e to select. 7 At Delete Entry?, < or > to Yes and press e to select, to delete the entry. The display shows positive mini notice. OR
< or > to No and press e to select to return to the previous screen. 8 Repeat Steps 4 to 9 to delete other entries. After deleting all required aliases or IDs, long press d to return to the Home screen. LKP_NAG-LACR.book Page 31 Tuesday, September 6, 2011 5:01 PM
Setting and Editing Priority for an Entry in the Scan List Procedure:
1 c to access the menu. 2 < or > to Scan and press e to select. 3 < or > to Scan List and press e to select. 4 < or > to the required alias or ID. 5 Press c to select. 6 < or > to Edit Priority and press e to select. 7 < or > to the required priority level and press e to select. 8 The display shows positive mini notice before returning to the previous screen. 9 The priority icon appears left of the members name. There is no priority icon if priority is set to None. Scan When you start a scan, your radio cycles through the programmed scan list for the current channel looking for voice activity. The LED blinks yellow and the scan icon appears on the status bar. During a dual mode scan, if you are on a digital channel, and your radio locks onto an analog channel, it automatically switches from digital mode to analog mode for the duration of the call. This is also true for the reverse. There are two ways of initiating scan:
Main Channel Scan (Manual): Your radio scans all the channels/groups in your scan list. On entering scan, your radio may depending on the settings automatically start on the last scanned active channel/group or on the channel where scan was initiated. Auto Scan (Automatic): Your radio automatically starts scanning when you select a channel/group that has Auto Scan enabled. NOTE: This feature is not applicable in Capacity Plus. 31 English LKP_NAG-LACR.book Page 32 Tuesday, September 6, 2011 5:01 PM Starting and Stopping Scan
Procedure:
Press the programmed Scan button to start or stop Scan. OR Follow the procedure below. 1 Use the Channel Selector Knob to select a channel programmed with a scan list. 2 c to access the menu. 3 < or > to Scan and press e to select. 4 < or > to Scan State and press e to select. 5 < or > to required scan state and press e to select. 6 The display shows Scan On when scan is enabled. The LED blinks yellow and the scan icon appears. OR The display shows Scan Off if scan is disabled. The LED turns off and the scan icon disappears. While scanning, the radio will only accept data (e.g. text message, location, or PC data) if received on its Selected Channel. 32 English Responding to a Transmission During a Scan
During scanning, your radio stops on a channel/group where activity is detected. The radio stays on that channel for a programmed time period known as hang time. Procedure:
1 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the transmitting radio releases the PTT button, indicating the channel is free for you to respond. 2 Press the PTT button during hang time. The LED lights up solid green. 3 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone. 4 Release the PTT button to listen. 5 If you do not respond within the hang time, the radio returns to scanning other channels/groups. LKP_NAG-LACR.book Page 33 Tuesday, September 6, 2011 5:01 PM Deleting a Nuisance Channel
If a channel continually generates unwanted calls or noise
(termed a nuisance channel), you can temporarily remove the unwanted channel from the scan list. This capability does not apply to the channel designated as the Selected Channel. Procedure:
1 When your radio locks on to an unwanted or nuisance channel, press the programmed Nuisance Channel Delete button until you hear a tone. 2 Release the Nuisance Channel Delete button. The nuisance channel is deleted. Deleting a nuisance channel is only possible through the programmed Nuisance Channel Delete button. This feature is not accessible through the menu. Restoring a Nuisance Channel
Procedure:
To restore the deleted nuisance channel, do one of the following:
Turn the radio off and then power it on again, OR Stop and restart a scan via the programmed Scan button or menu, OR Change the channel via the Channel Selector Knob. 33 English LKP_NAG-LACR.book Page 34 Tuesday, September 6, 2011 5:01 PM Vote Scan Contacts Settings Vote Scan provides you with wide area coverage in areas where there are multiple base stations transmitting identical information on different analog channels. Your radio scans analog channels of multiple base stations and performs a voting process to select the strongest received signal. Once that is established, your radio unmutes to transmissions from that base station. The LED blinks yellow and the vote scan icon appears on the status bar. To respond to a transmission during a Vote Scan, follow the same procedures as Responding to a Transmission During a Scan on page 32. 34 English Contacts provides address-book capabilities on your radio. Each entry corresponds to an alias or ID that you use to initiate a call. Each entry, depending on context, associates with one of five types of calls: Group Call, Private Call, All Call, PC Call or Dispatch Call. PC Call and Dispatch Call are data-related. They are only available with the applications. Refer to the data applications documentation for more information. NOTE:
If the Privacy feature is enabled on a channel, you can make privacy-enabled Group Call, Private Call, and All Call on that channel. Only target radios with the same Privacy Key OR the same Key Value and Key ID as your radio will be able to unscramble the transmission. See Privacy on page 50 for more information. Your radio supports two Contacts lists, one for Analog contacts and one for Digital contacts, with a maximum of 500 members for each Contacts list. Each entry within Contacts displays the following information:
Call Type Call Alias Call ID LKP_NAG-LACR.book Page 35 Tuesday, September 6, 2011 5:01 PM NOTE: You can add, or edit subscriber IDs for the Digital Contacts list. Deleting subscriber IDs can only be performed by your dealer. For the Analog Contacts list, you can only view the subcriber IDs, edit the subscriber IDs, and initiate a Call Alert. Adding and deleting capabilities can only be performed by your dealer. Making a Group Call from Contacts
Procedure:
1 c to access the menu. 2 < or > to Contacts and press e to select.The entries are alphabetically sorted. 7 Release the PTT button to listen. When any user in the group responds, the LED blinks green. You see the Group Call icon, the group ID, and that users ID on your display. 8 If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. OR If there is no voice activity for a programmed period of time, the call ends. 3 < or > to the required group alias or ID. 4 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 5 Press the PTT button to make the call. The LED lights up solid green. 6 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone. 35 English LKP_NAG-LACR.book Page 36 Tuesday, September 6, 2011 5:01 PM Making a Private Call from Contacts
Procedure:
1 c to access the menu. 2 < or > to Contacts and press e to select.The entries are alphabetically sorted. 3 < or > to the required subscriber alias or ID. 4 Press e to select. 5 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 6 Press the PTT button to make the call. The LED lights up solid green. The display shows the destination alias. 7 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. 8 Release the PTT button to listen. When the target radio responds, the LED blinks green and the display shows the transmitting user's ID. 10 You hear a short tone. The display shows Call Ended. Setting Default Contact
Procedure:
Follow the procedure below. 1 c to access the menu. 2 < or > to Contacts and press e to select. 3 < or > to the required alias or ID and press e to select. 4 < or > to Set as Default and press e to select. 5 The radio sounds a positive indicator tone and the display shows positive mini notice. 6 A appears beside the selected default alias or ID. 9 If the Channel Free Indication feature is enabled, you will hear a short alert tone the moment the target radio releases the PTT button, indicating the channel is free for you to respond. Press the PTT button to respond. OR If there is no voice activity for a programmed period of time, the call ends. 36 English LKP_NAG-LACR.book Page 37 Tuesday, September 6, 2011 5:01 PM Call Indicator Settings
Activating and Deactivating Call Ringers for Call Alert You can select, or turn on or off ringing tones for a received Call Alert. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Tones/Alerts and press e to select. 5 < or > to Call Ringers and press e to select. 6 < or > to Call Alert and press e to select. The current tone is indicated by a . 7 < or > to the required tone and press e to select. appears beside selected tone. NOTE: At Step 6, you can also use < or > to change the selected option.
Activating and Deactivating Call Ringers for Private Calls You can turn on or off the ringing tones for a received Private Call. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Tones/Alerts and press e to select. 5 < or > to Call Ringers and press e to select. 6 < or > to Private Call. 7 Press e to enable Private Call ringing tones. The display shows beside Enabled. OR Press e to disable Private Call ringing tones. The disappears from beside Enabled. NOTE: At Step 6, you can also use < or > to change the selected option. 37 English LKP_NAG-LACR.book Page 38 Tuesday, September 6, 2011 5:01 PM
Activating and Deactivating Call Ringers for Selective Call You can select, or turn on or off ringing tones for a received Selective Call. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Tones/Alerts and press e to select. 5 < or > to Call Ringers and press e to select. 6 < or > to Selective Call and press e to select. The current tone is indicated by a . 7 < or > to the required tone and press e to select. appears beside selected tone.
Activating and Deactivating Call Ringers for Text Message You can select, or turn on or off the ringing tones for a received Text Message. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Tones/Alerts and press e to select. 5 < or > to Call Ringers and press e to select. 6 < or > to Messages and press e to select. The current tone is indicated by a . 7 < or > to the required tone and press e to select. appears beside selected tone. NOTE: At Step 6, you can also use < or > to change the selected option. NOTE: At Step 6, you can also use < or > to change the selected option. 38 English LKP_NAG-LACR.book Page 39 Tuesday, September 6, 2011 5:01 PM Assigning Ring Styles
You can program your radio to sound one of ten predefined ringing tones when receiving a Call Alert or a Text Message from a particular contact. Procedure:
1 c to access the menu. 2 < or > to Contacts and press e to select.The entries are alphabetically sorted. 3 < or > to the required alias or ID and press e to select. 4 < or > to Edit and press e to select. 5 Press c until display shows Edit Ringtone menu. 6 A indicates the current selected tone. 7 < or > to the required tone and press e to select. appears beside selected tone. 8 The display shows a positive mini notice. The radio sounds out each ring style as you navigate through the list. Escalating Alarm Tone Volume
You can program your radio to continually alert you when a radio call remains unanswered. This is done by automatically increasing the alarm tone volume over time. This feature is known as Escalert. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Tones/Alerts and press e to select. 5 < or > to Escalert. 6 Press e to enable Escalert. The display shows beside Enabled. OR Press e to disable Escalert. The disappears from beside Enabled. NOTE: At Step 5, you can also use < or > to change the selected option. 39 English LKP_NAG-LACR.book Page 40 Tuesday, September 6, 2011 5:01 PM Call Log Features Your radio keeps track of all recent outgoing, answered, and missed Private Calls. Use the call log feature to view and manage recent calls. You can perform the following tasks in each of your call lists:
Delete View Details Viewing Recent Calls
The lists are Missed, Answered, and Outgoing. Procedure:
1 c to access the menu. 2 < or > to Call Log and press e to select. 3 < or > to required list and press e to select. 4 The display shows the most recent entry at the top of the list. 5 < or > to view the list. Press the PTT button to start a Private Call with the current selected alias or ID. 40 English Deleting a Call from a Call List
Procedure:
1 c to access the menu. 2 < or > to Call Log and press e to select. 3 < or > to the required list and press e to select. 4 < or > to the required alias or ID and press e to select. 5 < or > to Delete and press e to select. 6 Press e to select Yes to delete the entry. The display shows positive mini notice. OR
< or > to No to return to the previous screen. When you select a call list and it contains no entries, the display shows List Empty,. Viewing Details from a Call List
Procedure:
1 c to access the menu. 2 < or > to Call Log and press e to select. 3 < or > to the required list and press e to select. LKP_NAG-LACR.book Page 41 Tuesday, September 6, 2011 5:01 PM 4 < or > to the required alias or ID and press e to select. 5 < or > to View Details and press e to select. Display shows details. Call Alert Operation Call Alert paging enables you to alert a specific radio user to call you back when they are able to do so. This feature is applicable for subscriber aliases or IDs only and is accessible through the menu via Contacts. Receiving and Responding to a Call Alert
When you receive a Call Alert page, you see the notification list listing a Call Alert with the alias or ID of the calling radio on the display. Procedure:
1 You hear a repetitive tone. The LED blinks yellow. 2 Press the PTT button while the display still shows the Call Alert in the Notification List to respond with a Private Call. OR Press d to exit the Notification List. The alert is moved to the Missed Call Log. See Notification List on page 59 for details about the Notification List. See Call Log Features on page 40 for details about the Missed Call List. 41 English LKP_NAG-LACR.book Page 42 Tuesday, September 6, 2011 5:01 PM Making a Call Alert from the Contacts List
Procedure:
1 c to access the menu. 2 < or > to Contacts and press e to select. 3 < or > to the required subscriber alias or ID and press e to select. 4 < or > to Call Alert and press e to select. 5 The display shows Call Alert and the subscriber alias or ID, indicating that the Call Alert has been sent. 6 The LED lights up solid green when your radio is sending the Call Alert. 7 If the Call Alert acknowledgement is received, the display shows positive mini notice. OR If the Call Alert acknowledgement is not received, the display shows negative mini notice. 2 The display shows Call Alert and the subscriber alias or ID, indicating that the Call Alert has been sent. 3 The LED lights up solid green when your radio is sending the Call Alert. 4 If the Call Alert acknowledgement is received, the display shows positive mini notice. OR If the Call Alert acknowledgement is not received, the display shows negative mini notice.
Making a Call Alert with the One Touch Access Button Procedure:
1 Press the programmed One Touch Access button to make a Call Alert to the predefined alias or ID. 42 English LKP_NAG-LACR.book Page 43 Tuesday, September 6, 2011 5:01 PM Emergency Operation An Emergency Alarm is used to indicate a critical situation. You are able to initiate an Emergency at any time on any screen display even when there is activity on the current channel. Your dealer can set the duration of a button press for the programmed Emergency button, except for long press, which is similar with all other buttons:
Short press Between 0.05 seconds and 0.75 seconds Long press Between 1.00 second and 3.75 seconds The programmed Emergency button is assigned with the Emergency On/Off feature. Check with your dealer for the assigned operation of the Emergency button. If short press the programmed Emergency button is assigned to turn on the Emergency mode, then long press the programmed Emergency button is assigned to exit the Emergency mode. If long press the programmed Emergency button is assigned to turn on the Emergency mode, then short press the programmed Emergency button is assigned to exit the Emergency mode. NOTE: Side Button 1 or Side Button 2 can be programmed as the Emergency Button. Your radio supports three Emergency Alarms:
Emergency Alarm Emergency Alarm with Call Emergency Alarm with Voice to Follow In addition, each alarm has the following types:
Regular Radio transmits an alarm signal and shows audio and/or visual indicators. Silent Radio transmits an alarm signal without any audio or visual indicators. Radio receives calls without any sound through the radios speaker, until you press the PTT button to initiate the call. Silent with Voice Radio transmits an alarm signal without any audio or visual indicators, but allow incoming calls to sound through the radios speaker. Only ONE of the Emergency Alarms above can be assigned to the programmed Emergency button. 43 English LKP_NAG-LACR.book Page 44 Tuesday, September 6, 2011 5:01 PM Sending an Emergency Alarm
This feature allows you to send an Emergency Alarm, a non-voice signal, which triggers an alert indication on a group of radios. Procedure:
1 Press the programmed Emergency On button. 2 The display shows Tx Alarm and the destination alias. The LED lights up solid green and the Emergency icon appears. OR The display shows Tx Telegram and the destination alias. The LED lights up solid green and the Emergency icon appears. 3 When an Emergency Alarm acknowledgment is received, the Emergency tone sounds and the LED blinks green. The display shows Alarm Sent. OR If your radio does not receive an Emergency Alarm acknowledgement, and after all retries have been exhausted, a tone sounds and the display shows Alarm Failed. 4 Radio exits the Emergency Alarm mode and returns to the Home screen. If your radio is set to Silent, it will not display any audio or visual indicators during Emergency mode. 44 English Sending an Emergency Alarm with Call
This feature allows you to send an Emergency Alarm to a group of radios. Upon acknowledgement by a radio within the group, the group of radios can communicate over a programmed Emergency channel. Procedure:
1 Press the programmed Emergency On button. 2 The display shows Tx Alarm and the destination alias. The LED lights up solid green and the Emergency icon appears. OR The display shows Tx Telegram and the destination alias. The LED lights up solid green and the Emergency icon appears. 3 When an Emergency Alarm acknowledgment is received, the Emergency tone sounds and the LED blinks green. The display shows Alarm Sent. 4 Your radio enters the emergency call mode when the display shows Emergency and the destination group alias. 5 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 6 Press PTT button to make the call. The LED lights up solid green and the group icon appears on the display. LKP_NAG-LACR.book Page 45 Tuesday, September 6, 2011 5:01 PM 7 Wait for the Talk Permit Tone to finish (if enabled) and speak clearly into the microphone. OR Wait for the PTT Sidetone to finish (if enabled) and speak clearly into the microphone. 8 Release the PTT button to listen. When you receive a group call, the display shows the caller alias and group alias. 9 When the channel is free for you to respond, a short alert if the Channel Free Indication feature is tone sounds (
enabled). Press the PTT button to respond. OR Once your call ends, press the programmed Emergency Off button to exit the Emergency mode. 10 The radio returns to the Home screen. If your radio is set to Silent, it will not display any audio or visual indicators during Emergency mode, or allow any received calls to sound through the radios speaker, until you press the PTT button to initiate the call. If your radio is set to Silent with Voice, it will not display any audio or visual indicators during Emergency mode, but allow incoming calls to sound through the radios speaker. The indicators will only appear once you press the PTT button to initiate, or respond to, the call.
Sending an Emergency Alarm with Voice to Follow This feature allows you to send an Emergency Alarm to a group of radios. Your radios microphone is automatically activated, allowing you to communicate with the group of radios without pressing the PTT button. This activated microphone state is also known as hot mic. If you press the PTT button during the programmed hot mic transmission period, the radio ignores the PTT press and remains in Emergency mode. NOTE:
If you press the PTT button during hot mic, and continue to press it after the hot mic duration expires, the radio continues to transmit until you release the PTT button. Procedure:
1 Press the programmed Emergency On button. 2 The display shows Tx Alarm and the destination alias. The LED lights up solid green and the Emergency icon appears. OR The display shows Tx Telegram and the destination alias. The LED lights up solid green and the Emergency icon appears. 3 Once the display shows Alarm Sent, speak clearly into the microphone. When hot mic has been enabled, the radio 45 English LKP_NAG-LACR.book Page 46 Tuesday, September 6, 2011 5:01 PM automatically transmits without a PTT press until the hot mic duration expires. 4 While transmitting, the LED lights up solid green and the Emergency icon appears. 5 Once the hot mic duration expires, the radio automatically stops transmitting. To transmit again, press the PTT button. 6 Press the programmed Emergency Off button to exit the Emergency mode. 7 The radio returns to the Home screen. If your radio is set to Silent, it will not display any audio or visual indicators during Emergency mode, or allow any received calls to sound through the radios speaker, until the programmed hot mic transmission period is over, and you press the PTT button. If your radio is set to Silent with Voice, it will not display any audio or visual indicators during Emergency mode when you are making the call with hot mic, but allow sound through the radios speaker when the target radio responds after the programmed hot mic transmission period is over. The indicators will only appear when you press the PTT button. NOTE:
If the Emergency Alarm request fails, the radio does not retry to send the request, and enters the hot mic state directly.
Reinitiating an Emergency Mode NOTE: This feature is only applicable to the radio sending the Emergency Alarm. There are two instances where this can happen:
You change the channel while the radio is in Emergency mode. This exits the Emergency mode. If Emergency Alarm is enabled on this new channel, the radio reinitiates Emergency. You press the programmed Emergency On button during an Emergency initiation/transmission state. This causes the radio to exit this state, and to reinitiate Emergency.
Exiting Emergency Mode NOTE: This feature is only applicable to the radio sending the Emergency Alarm. Your radio exits Emergency mode when one of the following occurs:
Emergency Alarm acknowledgement is received (for Emergency Alarm only), OR An Emergency Exit Telegram is received, OR All retries to send the alarm have been exhausted, OR The Emergency Off button is pressed. 46 English LKP_NAG-LACR.book Page 47 Tuesday, September 6, 2011 5:01 PM NOTE:
If your radio is powered off, it exits the Emergency mode. The radio will not reinitiate the Emergency mode automatically when it is turned on again. If you change channels when your radio is in Emergency mode to a channel that has no emergency system configured, No Emergency is shown on your display. 47 English LKP_NAG-LACR.book Page 48 Tuesday, September 6, 2011 5:01 PM 48 English LKP_NAG-LACR.book Page 49 Tuesday, September 6, 2011 5:01 PM Analog Message Encode Analog Status Update Your radio is able to send preprogrammed messages from the Message list to a radio alias or to the dispatcher. Sending MDC Message Encode to Dispatcher
Procedure:
1 < or > to Message and press to select. 2 < or > to Quick Text and press to select. 3 < or > to the required message. Press to send. 4 The display shows transitional mini notice, confirming your message is being sent. 5 If the message is sent, a tone sounds and the display shows positive mini notice. OR If the message is not sent, a low tone sounds and the display shows negative mini notice. Your radio is able to send preprogrammed messages from the Status List indicating your current activity to a radio contact (for 5-Tone systems) or to the dispatcher (for MDC systems). The last acknowledged message is kept at the top of the Status List. The other messages are arranged in alphanumeric order. Sending Status Update to Predefined Contact
Procedure:
1 < or > to Status and press e to select. 2 < or > to the required status. Press e to select. 3 < or > to Set as Default. Press e to send the status update. 4 The display shows transitional mini notice, confirming your status update is being sent. 5 If the status update is acknowledged, a tone sounds and the display shows positive mini notice. A appears beside the acknowledged status. OR If the status update is not acknowledged, a low tone sounds and the display shows negative mini notice. A remains beside the previous status. 49 English LKP_NAG-LACR.book Page 50 Tuesday, September 6, 2011 5:01 PM Privacy If enabled, this feature helps to prevent eavesdropping by unauthorized users on a channel by the use of a software-
based scrambling solution. The signaling and user identification portions of a transmission are not scrambled. Your radio must have privacy enabled on the channel to send a privacy-enabled transmission, although this is not a necessary requirement for receiving a transmission. While on a privacy-
enabled channel, the radio is still able to receive clear
(unscrambled) transmissions. Your radio supports two types of privacy:
Basic Privacy Enhanced Privacy. (A Software License Key sold separately is required for this feature.) Only ONE of the privacy types above can be assigned to the radio. To unscramble a privacy-enabled call or data transmission, your radio must be programmed to have the same Privacy Key (for Basic Privacy), OR the same Key Value and Key ID (for Enhanced Privacy) as the transmitting radio. If your radio receives a scrambled call that is of a different Privacy Key, OR a different Key Value and Key ID, you will either hear a garbled transmission (Basic Privacy) or nothing at all (Enhanced Privacy). 50 English The LED lights up solid green while the radio is transmitting and double blinks green when the radio is receiving an ongoing privacy-enabled transmission. Some radio models may not offer this Privacy feature. Check with your dealer or system administrator for more information.Procedure:
Press the programmed Privacy button to toggle privacy on or off. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Privacy 5 Press e to enable Privacy. The display shows beside Enabled. OR Press e to disable Privacy. The disappears from beside Enabled. If the radio has a privacy type assigned, secure or unsecure icon appears on the status bar, except when the radio is sending or receiving an Emergency call or alarm. LKP_NAG-LACR.book Page 51 Tuesday, September 6, 2011 5:01 PM NOTE: At Step 4, you can also use < or > to change the selected option. IP Site Connect Dual Tone Multi Frequency (DTMF) The Dual Tone Multi Frequency (DTMF) feature allows the radio to operate in a radio system with an interface to telephone systems. Procedure:
To initiate a DTMF call. 1 Press and hold the PTT button. 2 Enter the desired number, * or #. You can turn off the DTMF tone by disabling all radio tones and alerts (see Turning the Radio Tones/Alerts On or Off on page 60). This feature allows your radio to extend communication beyond the reach of a single site, by connecting to different available sites via an Internet Protocol (IP) network. A Software License Key sold separately is required for this feature. NOTE: This feature is not applicable in Capacity Plus. When the radio moves out of range from one site and into the range of another, it connects to the new site's base station to send or receive calls/data transmissions. Depending on your settings, this is done automatically or manually. If the radio is set to do this automatically, it scans through all available sites when the signal from the current site is weak or when the radio is unable to detect any signal from the current site. It then locks on to the base station with the strongest Received Signal Strength Indicator (RSSI) value. In a manual site search, the radio searches for the next site in the roam list that is currently in range (but which may not have the strongest signal) and locks on to it. NOTE: Each channel can only have either Scan or Roam enabled, not both at the same time. Channels with this feature enabled can be added to a particular roam list. The radio searches the channel(s) in the Members list during the automatic roam operation to locate the best site. 51 English LKP_NAG-LACR.book Page 52 Tuesday, September 6, 2011 5:01 PM A Members list supports a maximum of 16 channels (including the Selected Channel). NOTE: You cannot manually add or delete an entry to the Members list. Check with your dealer or system administrator for more information. Starting an Automatic Site Search
NOTE: The radio only scans for a new site if the current signal is weak or when the radio is unable to detect any signal from the current site. If the RSSI value is strong, the radio remains on the current site. Procedure:
Press the programmed Site Lock On/Off button. 1 A tone sounds and the display shows Site Unlocked. 2 The LED blinks yellow rapidly when the radio is actively searching for a new site, and turns off once the radio locks on to a site. 3 The display shows the channel alias and the site roaming icon appears. Procedure:
Use the menu. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Site Roaming and press e to select. 5 < or > to Unlock Site and press e to select. A tone sounds and the display shows Site Unlocked. 6 The radio returns to the Home screen. 7 The LED blinks yellow rapidly when the radio is actively searching for a new site, and turns off once the radio locks on to a site. The radio also performs an automatic site search (site is unlocked) during a PTT button press or data transmission if the current channel, an IP Site Select channel with an attached roam list, is out of range. OR 52 English LKP_NAG-LACR.book Page 53 Tuesday, September 6, 2011 5:01 PM Stopping an Automatic Site Search
When the radio is actively searching for a new site:
Procedure:
Press the programmed Site Lock On/Off button. 1 A tone sounds and the display shows Site Locked. 2 The LED turns off and the display shows the channel alias. OR Procedure:
Use the menu. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Site Roaming and press e to select. 5 < or > to Lock Site State. 6 Press e to lock site. The display shows beside Enabled. OR Press e to unlock site. The disappears from beside Enabled. 7 The LED turns off and the radio returns to the Home screen. The display shows the channel alias. NOTE: At Step 5, you can also use < or > to change the selected option. Starting a Manual Site Search
Procedure:
Press the programmed Manual Site Roam button and proceed to Step 6. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press c to select. 3 < or > to Radio Settings and press c to select. 4 < or > to Site Roaming and press c to select. 5 < or > to Active Search and press c to select. 6 A tone sounds and the display shows Finding Site. The LED blinks green. 7 If a new site is found, a tone sounds and the LED turns off. The display shows Site <Alias> Found. OR If there is no available site within range, a tone sounds and the LED turns off. The display shows Out of Range. OR If a new site is within range, but the radio is unable to 53 English LKP_NAG-LACR.book Page 54 Tuesday, September 6, 2011 5:01 PM connect to it, a tone sounds and the LED turns off. The display shows Channel Busy. 8 The radio returns to the Home screen. Security You can enable or disable any radio in the system. For example, you might want to disable a stolen radio, to prevent the thief from using it, and enable that radio, when it is recovered. NOTE: Performing Radio Disable and Enable is limited to radios with these functions enabled. Check with your dealer or system administrator for more information. Radio Disable
Procedure:
Use the programmed Radio Disable button. 1 Press the programmed Radio Disable button. 2 < or >to the required alias or ID and press e to select. 3 The display shows transitional mini notice, indicating the request is in progress. The LED blinks green. 4 Wait for acknowledgment. 5 If successful, a positive indicator tone sounds and the display shows positive mini notice. OR If unsuccessful, a negative indicator tone sounds and the display shows negative mini notice. 54 English LKP_NAG-LACR.book Page 55 Tuesday, September 6, 2011 5:01 PM OR Procedure:
Use the menu. 1 c to access the menu. 2 < or > to Contacts and press e to select. The entries are alphabetically sorted. 3 < or > to the required alias or ID and press e to select.
< or > to Radio Disable and press e to select. 4 The display shows transitional mini notice, indicating the request is in progress. The LED blinks green. 5 Wait for acknowledgment. 6 If successful, a positive indicator tone sounds and the display shows positive mini notice. OR If unsuccessful, a negative indicator tone sounds and the display shows negative mini notice. Do not press d during the Radio Disable operation as you will not get an acknowledgement message. Radio Enable
Procedure:
Use the programmed Radio Enable button. 1 Press the programmed Radio Enable button. 2 < or > to the required alias or ID and press e to select. 3 The display shows Radio Enable and the subscriber alias or ID. The LED lights up solid green. 4 Wait for acknowledgment. 5 If successful, the radio sounds a positive indicator tone and the display shows positive mini notice. OR If unsuccessful, the radio sounds a negative indicator tone and the display shows negative mini notice. OR Procedure:
Use the menu. 1 c to access the menu. 2 < or > to Contacts and press e to select. The entries are alphabetically sorted. 3 < or > to the required alias or ID and press e to select. 55 English LKP_NAG-LACR.book Page 56 Tuesday, September 6, 2011 5:01 PM 4 < or > to Radio Enable and press e to select. The LED blinks green. 5 The display shows Radio Enable and the subscriber alias or ID. The LED lights up solid green. 6 Wait for acknowledgment. 7 If successful, the radio sounds a positive indicator tone and the display shows positive mini notice. OR If unsuccessful, the radio sounds a negative indicator tone and the display shows negative mini notice. Do not press d during the Radio Enable operation as you will not get an acknowledgement message. Lone Worker This feature prompts an emergency to be raised if there is no user activity, such as any radio button press or activation of the channel selector, for a predefined time. Following no user activity for a programmed duration, the radio pre-warns the user via an audio indicator once the inactivity timer expires. If there is still no acknowledgment by the user before the predefined reminder timer expires, the radio initiates an Emergency Alarm. Only one of the following Emergency Alarms is assigned to this feature:
Emergency Alarm Emergency Alarm with Call Emergency Alarm with Voice to Follow The radio remains in the emergency state allowing voice messages to proceed until action is taken. See Emergency Operation on page 43 on ways to exit Emergency. NOTE: This feature is limited to radios with this function enabled. Check with your dealer or system administrator for more information. 56 English LKP_NAG-LACR.book Page 57 Tuesday, September 6, 2011 5:01 PM Password Lock Features If enabled, this feature allows you to access your radio via password upon powering up. Accessing the Radio from Password
Procedure:
Power up the radio. 1 You will be prompt to enter a four-digit password. 2 Enter your current four-digit password. Press < or >
to choose each digits numeric value (0-9). Press >or c to move to next digit. Each digit changes to . Press e to confirm your selection. You hear a positive indicator tone for every digit pressed. Press < to remove the each on the display. 3 If the password is correct:
Your radio proceeds to power up. See Powering Up the Radio on page 5. OR If the password is incorrect:
The display shows Wrong Password. Repeat Step 2. OR After the third incorrect password, the display shows Wrong Password and then, shows Radio Locked. A tone sounds and the LED double blinks yellow. Your radio enters into locked state for 15 minutes, and responds to inputs from On/Off/Volume Control Knob and programmed Backlight Auto button only. NOTE: The radio is unable to receive any call, including emergency calls, in locked state. Unlocking the Radio from Locked State
Procedure:
Wait for 15 minutes. Repeat Steps 1 to 3 in Accessing the Radio from Password on page 57. OR Power up the radio, if you have powered down the radio during locked state:
1 A tone sounds and the LED double blinks yellow. The display shows Radio Locked. 2 Wait for 15 minutes. Repeat Accessing the Radio from Password on page 57. Your radio restarts the 15 minutes timer for locked state when you power up. 57 English LKP_NAG-LACR.book Page 58 Tuesday, September 6, 2011 5:01 PM Turning the Password Lock On or Off
Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Passwd Lock and press e to select. 5 Enter your current four-digit password. See Step 2 in Accessing the Radio from Password on page 57. Changing the Password
Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Passwd Lock and press e to select. 5 Enter your current four-digit password. See Step 2 in Accessing the Radio from Password on page 57. 6 If the password is correct:
Press e to enable Password Lock. The display shows beside Enabled. OR Press e to disable Password Lock. The disappears from beside Enabled. OR If the password is incorrect:
The display shows Wrong Password and automatically returns to the previous menu. NOTE: At Step 6, you can also use < or > to change the selected option. 58 English 6 If the password is correct:
< or > to Change Pwd and press e to select. OR If the password is incorrect:
The display shows Wrong Password and automatically returns to the previous menu. 7 Enter a new four-digit password. See Step 2 in Accessing the Radio from Password on page 57. 8 Re-enter the new four-digit password. See Step 2 in Accessing the Radio from Password on page 57. 9 If both of the new password inputs match:
The display shows Password Changed. OR LKP_NAG-LACR.book Page 59 Tuesday, September 6, 2011 5:01 PM If both of the new password inputs do not match:
The display shows Passwords Do Not Match. 10 The screen automatically returns to the previous menu. Notification List Your radio has a Notification List that collects all your unread events on the channel, such as unread text messages, telegrams, missed calls, and call alerts. The Notification icon appears on the status bar when the Notification List has one or more events. The list supports a maximum of forty (40) unread events. When it is full, the next event automatically replaces the oldest event. After the events are read, they are removed from the Notification List. Accessing the Notification List
Procedure:
1 c to access the menu. 2 < or > to Notification and press e to select. 3 < or > to the required event and press e to select. Long press d to return to the Home screen. 59 English LKP_NAG-LACR.book Page 60 Tuesday, September 6, 2011 5:01 PM Utilities NOTE: At Step 5, you can also use < or > to change the selected option. Turning the Radio Tones/Alerts On or Off
You can enable and disable all radio tones and alerts (except for the incoming Emergency alert tone) if needed. Procedure:
Press the programmed All Tones/Alerts button to toggle all tones on or off. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Tones/Alerts and press e to select. 5 < or > to All Tones and press e to select. 6 Press e to enable all tones. The display shows beside Enabled. OR Press e to disable all tones. The disappears from beside Enabled. 60 English Setting the Tone Alert Volume Offset Level
You can adjust the Tone Alert Volume Offset level if needed. This feature adjusts the volume of the tones/alerts, allowing it to be higher or lower than the voice volume. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Tones/Alerts and press e to select. 5 < or > to Vol. Offset and press e to select. 6 < or > to the required volume value. The radio sounds a feedback tone with each corresponding volume value. 7 Press e to keep the required displayed volume value. OR Repeat Step 6 to select another volume value. OR d to exit without changing the current volume offset settings. LKP_NAG-LACR.book Page 61 Tuesday, September 6, 2011 5:01 PM Turning the Talk Permit Tone On or Off
You can enable and disable the Talk Permit Tone if needed. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Tones/Alerts and press e to select. 5 < or > to Talk Permit and press e to select. 6 Press e to enable Talk Permit Tone. The display shows beside Enabled. OR Press e to disable Talk Permit Tone. The disappears from beside Enabled. NOTE: At Step 5, you can also use < or > to change the selected option. Setting the Power Level
You can customize your radios power setting to high or low for each channel. Settings: High enables communication with radios located at a considerable distance from you. Low enables communication with radios in closer proximity. Procedure:
Press the programmed Power Level button to toggle transmit power level between high and low. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Power and press e to select. 5 < or > to the required setting and press c to select. appears beside selected setting. 6 Screen returns to the previous menu. Long press d to return to the Home screen. The power level icon is visible. 61 English LKP_NAG-LACR.book Page 62 Tuesday, September 6, 2011 5:01 PM NOTE: At Step 4, you can also use < or > to change the selected option. Adjusting the Display Brightness
You can adjust radios display brightness as needed. Procedure:
Press the programmed Brightness button and proceed to Step 5. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Brightness and press e to select. 5 The display shows a progress bar. Decrease display brightness by pressing < or increase the display brightness by pressing >. Press e to confirm your entry. 62 English Controlling the Display Backlight
You can enable or disable the radios display backlight as needed. The setting also affects the Menu Navigation Buttons. Procedure:
Press the programmed Backlight Auto button to toggle the backlight settings. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Backlight Auto 5 Press e to enable backlight. The display shows beside Enabled. OR Press e to disable backlight. The disappears from beside Enabled. The display backlight are automatically turned off if the LED indicator is disabled (see Turning the LED Indicator On or Off on page 64). NOTE: At Step 4, you can also use < or > to change the selected option. LKP_NAG-LACR.book Page 63 Tuesday, September 6, 2011 5:01 PM Setting the Squelch Level
You can adjust your radio's squelch level to filter out unwanted calls with low signal strength or channels that have a higher than normal background noise. Settings: Normal is the default. Tight filters out (unwanted) calls and/or background noise. However, calls from remote locations may also be filtered out. Procedure:
Press the programmed Squelch button to toggle squelch level between normal and tight. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Squelch and press e to select. 5 The display shows Tight and Normal. < or > to the required setting and press e to enable. appears besides selected setting. 6 Screen returns to the previous menu. NOTE: At Step 4, you can also use < or > to change the selected option. Turning the Introduction Screen On or Off
You can enable and disable the Introduction Screen if needed. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Intro Screen and press e to select. 5 Press e to enable Introduction Screen. The display shows
beside Enabled. OR Press e to disable Introduction Screen. The disappears from beside Enabled. NOTE: At Step 4, you can also use < or > to change the selected option. 63 English LKP_NAG-LACR.book Page 64 Tuesday, September 6, 2011 5:01 PM Language
You can set your radio display to be in your required language. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Language and press e to select. 4 < or > to the required language and press e to enable. appears beside selected language. NOTE: At Step 4, you can also use < or > to change the selected option. 64 English Turning the LED Indicator On or Off
You can enable and disable the LED Indicator if needed. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to LED Indicator and press e to select. 5 Press e to enable LED indicator. The display shows beside Enabled. OR Press e to disable LED indicator. The disappears from beside Enabled. The display backlight, and buttons backlighting are automatically turned off if the LED indicator is disabled (see Controlling the Display Backlight on page 62). NOTE: At Step 4, you can also use < or > to change the selected option.
Turning the Voice Operating Transmission (VOX) Feature On or Off This feature allows you to initiate a hands-free voice activated call on a programmed channel. The radio automatically LKP_NAG-LACR.book Page 65 Tuesday, September 6, 2011 5:01 PM transmits, for a programmed period, whenever the microphone on the VOX-capable accessory detects voice. Pressing the PTT button during radio operation will disable VOX. To re-enable VOX, do one of the following:
Turn the radio off and power it on again, OR Change the channel via the Channel Selector Knob, OR Follow the procedure below. NOTE: Turning this feature on or off is limited to radios with this function enabled. Check with your dealer or system administrator for more information. Procedure:
Press the programmed VOX button to toggle the feature on or off. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to VOX. 5 Press e to enable VOX. The display shows beside Enabled. OR Press e to disable VOX. The disappears from beside Enabled. If the Talk Permit Tone feature is enabled (see Turning the Talk Permit Tone On or Off on page 61), use a trigger word to initiate the call. Wait for the Talk Permit Tone to finish before speaking clearly into the microphone. NOTE: At Step 4, you can also use < or > to change the selected option. Voice Announcement
This feature enables the radio to audibly indicate the current Zone or Channel the user has just assigned, or programmable button press. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display. Use the following features to toggle Voice Announcement on or off. Procedure:
Press the programmed Voice Announcement button. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press e to select. 65 English LKP_NAG-LACR.book Page 66 Tuesday, September 6, 2011 5:01 PM 3 < or > to Voice Announcement. 4 Press e to enable Voice Announcement. The display shows beside Enabled. OR Press e to disable Voice Announcement. The disappears from beside Enabled. NOTE: At Step 3, you can also use < or > to change the selected option. 66 English Call Forwarding
You can enable your radio to automatically forward voice calls to another radio. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Call Forward. 4 Press e to enable Call Forwarding. The display shows beside Enabled. OR Press e to disable Call Forwarding. The disappears from beside Enabled. NOTE: At Step 3, you can also use < or > to change the selected option. LKP_NAG-LACR.book Page 67 Tuesday, September 6, 2011 5:01 PM Menu Timer
Set the period of time your radio stays in the menu before it automatically switches to the Home screen. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Menu Timer and press e to select. 5 < or > to the required setting and press e to enable. Analog Mic AGC
This feature controls the your radio's microphone gain automatically while transmitting on an analog system. It supresses loud audio or boosts soft audio to a preset value in order to provide a consistent level of audio. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Analog Mic AGC. 5 Press e to enable Analog Mic AGC. The display shows beside Enabled. OR Press e to disable Analog Mic AGC. The disappears from beside Enabled. NOTE: At Step 3, you can also use < or > to change the selected option. 67 English LKP_NAG-LACR.book Page 68 Tuesday, September 6, 2011 5:01 PM Digital Mic AGC
This feature controls the your radio's microphone gain automatically while transmitting on an digital system. It supresses loud audio or boosts soft audio to a preset value in order to provide a consistent level of audio. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Digital Mic AGC. 5 Press e to enable Digital Mic AGC. The display shows beside Enabled. OR Press e to disable Digital Mic AGC. The disappears from beside Enabled. NOTE: At Step 3, you can also use < or > to change the selected option. 68 English Intelligent Audio
Your radio automatically adjusts its audio volume to overcome current background noise in the environment. Use the following features to toggle Intelligent Audio on or off. Procedure:
Press the programmed Intelligent Audio button to toggle the feature on or off. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Settings and press e to select. 4 < or > to Intelligent Audio. 5 Press e to enable Intelligent Audio. The display shows beside Enabled. OR Press e to disable Intelligent Audio. The disappears from beside Enabled. NOTE: At Step 3, you can also use < or > to change the selected option. LKP_NAG-LACR.book Page 69 Tuesday, September 6, 2011 5:01 PM Accessing General Radio Information
Your radio contains information on the following:
Battery Radio Alias and ID Firmware and Codeplug Versions NOTE: Press d at any time to return to the previous screen or long press d to return to the Home screen. The radio exits the current screen once the inactivity timer expires. Accessing the Battery Information
Displays information on your radio battery. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Info and press e to select. 4 < or > to Battery Info and press e to select. 5 The display shows the battery information. OR For IMPRES batteries ONLY: The display reads Recondition Battery if the battery requires reconditioning in an IMPRES charger. After the reconditioning process, the display then shows the battery information. Checking the Radio Alias and ID
Displays the ID of your radio. Procedure:
Press the programmed Radio Alias and ID button to check your radio alias and ID. You hear a positive indicator tone. OR Follow the procedure below. 1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Info and press e to select. 4 < or > to My Number and press e to select. 5 The first line of the display shows the radio alias. The second line of the display shows the radio ID You can also press the programmed Radio Alias and ID button to return to the previous screen. 69 English LKP_NAG-LACR.book Page 70 Tuesday, September 6, 2011 5:01 PM Checking the Firmware Version and Codeplug
Version Displays the firmware and codeplug versions on your radio. Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Radio Info and press e to select. 4 < or > to Versions and press e to select. 5 The display shows the current firmware and codeplug versions. 70 English Front Panel Configuration (FPC) Your radio is able to customize certain feature parameters to enhance the use of your radio. Entering FPC Mode
Procedure:
1 c to access the menu. 2 < or > to Utilities and press e to select. 3 < or > to Program Radio and press e to select. NOTE: Long press d at any time to return to the Home screen. Editing FPC Mode Parameters
Use the following buttons as required while navigating through the feature parameters.
<, > Scroll through options, increase/decrease values, or navigate vertically e Select the option or enter a sub-menu d Short-press to return to previous menu or to exit the selection screen. Long-press to return to Home screen. LKP_NAG-LACR.book Page 71 Tuesday, September 6, 2011 5:01 PM Accessories Your radio is compatible with the accessories listed in this chapter. Contact your dealer for details. Antennas The diagram on the right shows the location of the color indicator for the following antennas. See the footnote at the end of the list for the colors. VHF, 136-155MHz, Helical Antenna (PMAD4117_) VHF, 144-165MHz, Helical Antenna (PMAD4116_) VHF, 152-174MHz, Helical Antenna (PMAD4118_) VHF, 136-148MHz, Stubby Antenna (PMAD4119_) VHF, 146-160MHz, Stubby Antenna (PMAD4120_) VHF, 160-174MHz, Stubby Antenna (PMAD4121_) UHF, 403-527MHz, Whip Antenna (PMAE4068_) UHF, 403-450MHz, Stubby Antenna (PMAE4069_) UHF, 440-490MHz, Stubby Antenna (PMAE4070_) UHF, 470-527MHz, Stubby Antenna (PMAE4071_) Color Code:
1. Red 2. Green 3. Black 4. Yellow 5. Blue 6. White 7. Brown 8. Orange 9. Purple 10. Batteries Core NiMH, 1300mAH IP56 Battery (PMNN4415_) Core Slim Li-Ion, 1500mAH IP56 Battery (PMNN4417_) IMPRES Li-Ion Slim, 1500mAH IP56 Battery (PMNN4416_) IMPRES Li-Ion Non-FM, 2150mAH IP56 Battery
(PMNN4418_) A c c e s s o r i e s 71 English LKP_NAG-LACR.book Page 72 Tuesday, September 6, 2011 5:01 PM Cables Chargers Programming Cable USB (PMKN4115_) Programming Cable Slim Connector to DB25 and TTR
(PMKN4116_) Programming Cable Slim Connector to DB25 and USB Plug
(PMKN4117_) Carry Devices Hard Leather Carry Case with 3-Inch Fixed Belt Loop for Limited Keypad Radio (PMLN5863_) Hard Leather Carry Case with 3-Inch Swivel Belt for Limited Keypad Radio (PMLN5865_) Hard Leather Carry Case with 2.5-Inch Swivel Belt Loop for Limited Keypad Radio (PMLN5867_) Nylon Carry Case with 3-Inch Fixed Belt Loop for Limited Keypad Radio (PMLN5869_) Belt Clip for 2-Inch Belt Width (PMLN4651_) Belt Clip for 2.5-Inch Belt Width (PMLN7008_) 2.5-Inch Replacement Leather Swivel Belt Loop
(PMLN5610_) 3-Inch Replacement Leather Swivel Belt Loop (PMLN5611_) s e i r o s s e c c A IMPRES Single-Unit Charger, Base Only (WPLN4226_) IMPRES Single-Unit Charger (WPLN4255_) IMPRES Single-Unit Charger (WPLN4256_) IMPRES Multi-Unit Charger, Base Only (WPLN4211_) IMPRES Multi-Unit Charger, US/NA Plug (WPLN4212_) IMPRES Multi-Unit Charger, Euro Plug (WPLN4213_) IMPRES Multi-Unit Charger, UK Plug (WPLN4214_) IMPRES Multi-Unit Charger, Australia/NZ Plug (WPLN4215_) IMPRES Multi-Unit Charger, Korea Plug (WPLN4217_) IMPRES Multi-Unit Charger with Display Base Only
(WPLN4218_) IMPRES Multi-Unit Charger with Display, US/NA Plug
(WPLN4219_) IMPRES Multi-Unit Charger with Display, Euro Plug
(WPLN4220_) IMPRES Multi-Unit Charger with Display, UK Plug
(WPLN4221_) IMPRES Multi-Unit Charger with Display, Australia/NZ Plug
(WPLN4222_) 72 English LKP_NAG-LACR.book Page 73 Tuesday, September 6, 2011 5:01 PM IMPRES Multi-Unit Charger with Display, Korea Plug
(WPLN4224_) Core Single Unit Charger (NNTN8117_) Assembly, Accessory, LTD SUC IMPRESS SMPS Euro
(WPLN4255_) Assembly, Accessory, LTD SUC IMPRESS SMPS Aus/NZ
(WPLN4256_) Earbuds and Earpieces Earbud with In-Line Mic/PTT, MagOne (PMLN5733_) Earpiece In-Line Mic/PTT Swivel, MagOne (PMLN5727_) Earset with Boom Microphone, MagOne (PMLN5732) Receive-Only Covered Earbud with Coiled Cord, for Remote Speaker Microphone (AARLN4885_) Receive-Only Flexible Earpiece for Remote Speaker Microphone (WADN4190_) D-Shell Receive Only Earpiece (One Size) for Remote Speaker Microphone (PMLN4620_) Receiver-Only Earpiece with Translucent Tube and Rubber Eartip for Remote Speaker Microphone (RLN4941_) A c c e s s o r i e s Headsets and Headset Accessories Heavy Duty Headset, Noise Cancelling with In-Line PTT
(PMLN5731_) Remote Speaker Microphones IMPRES Remote Speaker Microphone Large, Noise Cancelling with 3.5mm Jack (PMMN4071_) IMPRES Remote Speaker Microphone Small, with 3.5mm Jack (PMMN4073_) Remote Speaker Microphone Small, No Emergency, IP57
(PMMN4075_) Remote Speaker Microphone Small with 3.5mm Jack
(PMMN4076_) Surveillance Accessories 2-Wire Surveillance Kit, Black (PMLN5724_) 2-Wire Surveillance Kit, Beige (PMLN5726_) 73 English LKP_NAG-LACR.book Page 74 Tuesday, September 6, 2011 5:01 PM Miscellaneous Accessories Adjustable Black Nylon Carrying Strap (Attaches to D-Ring on Carry Case) (NTN5243_) Universal Chest Pack (HLN6602_) Break-A-Way Chest Pack with Radio Holder, Pen Holder and Velcro Secured Pouch (RLN4570_) Replacement Strap for HLN6602A and RLN4570A
(1505596Z02) RadioPAK Radio Utility Case (Fanny Pack) (RLN4815_) RadioPAK Extension Belt (for Waists Larger than 40 Inch)
(4280384F89) Waterproof Bag with Large Strap (HLN9985_) Small Clip, Epaulet Strap (RLN4295_) 1.75 Inch Wide Leather Belt (4200865599) s e i r o s s e c c A 74 English LKP_NAG-LACR.book Page 75 Tuesday, September 6, 2011 5:01 PM Batteries and Chargers Warranty The Workmanship Warranty The workmanship warranty guarantees against defects in workmanship under normal use and service. All MOTOTRBO Batteries IMPRES Chargers (Single-Unit and Multi-Unit, Non-Display) IMPRES Chargers (Multi-Unit with Display) Two (2) Years Two (2) Years One (1) Year The Capacity Warranty The capacity warranty guarantees 80% of the rated capacity for the warranty duration. Nickel Metal-Hydride (NiMH) or Lithium-Ion
(Li-lon) Batteries IMPRES Batteries, When Used Exclusively with IMPRES Chargers 12 Months 18 Months B a t t e r i e s a n d C h a r g e r s W a r r a n t y 75 English LKP_NAG-LACR.book Page 76 Tuesday, September 6, 2011 5:01 PM Limited Warranty MOTOROLA COMMUNICATION PRODUCTS I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:
MOTOROLA SOLUTIONS, INC. (MOTOROLA) warrants the MOTOROLA manufactured Communication Products listed below
(Product) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:
XPR Series Digital Portable Radios Two (2) Years Product Accessories (Excluding Batteries and Chargers) One (1) Year MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA. This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no y t n a r r a W d e t i m L i 76 English obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product. MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. II. GENERAL PROVISIONS:
This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLAs option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR LKP_NAG-LACR.book Page 77 Tuesday, September 6, 2011 5:01 PM INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. C)Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. III. STATE LAW RIGHTS:
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. IV. HOW TO GET WARRANTY SERVICE:
You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at 1-800-927-2744 US/Canada. V. WHAT THIS WARRANTY DOES NOT COVER:
A) Defects or damage resulting from use of the Product in other than its normal and customary manner. B) Defects or damage from misuse, accident, water, or neglect. i L m i t e d W a r r a n t y D)Breakage or damage to antennas unless caused directly by defects in material workmanship. E) A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim. F) Product which has had the serial number removed or made illegible. G)Rechargeable batteries if:
(1) any of the seals on the battery enclosure of cells are broken or show evidence of tampering.
(2) the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified. H)Freight costs to the repair depot. I) A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLAs published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA. J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. K) Normal and customary wear and tear. 77 English LKP_NAG-LACR.book Page 78 Tuesday, September 6, 2011 5:01 PM VI. PATENT AND SOFTWARE PROVISIONS:
MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:
A) that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;
B) that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and C)should the Product or parts become, or in MOTOROLAs opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA. y t n a r r a W d e t i m L i 78 English MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights. VII. GOVERNING LAW:
This Warranty is governed by the laws of the State of Illinois, U.S.A.
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2012-05-22 | 136 ~ 174 | TNF - Licensed Non-Broadcast Transmitter Held to Face | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2012-05-22
|
||||
1 | Applicant's complete, legal business name |
Motorola Solutions, Inc.
|
||||
1 | FCC Registration Number (FRN) |
0025009739
|
||||
1 | Physical Address |
1303 East Algonquin Road
|
||||
1 |
Schaumburg, Illinois 60196
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
n/a | ||||||
app s | FCC ID | |||||
1 | Grantee Code |
ABZ
|
||||
1 | Equipment Product Code |
99FT3088
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
R****** S******
|
||||
1 | Telephone Number |
847-3********
|
||||
1 | Fax Number |
847-5********
|
||||
1 |
B******@motorolasolutions.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Motorola Solutions, Inc.
|
||||
1 | Name |
L****** D****** L********
|
||||
1 | Physical Address |
1301 E. Algonquin Rd.
|
||||
1 |
Schaumburg, Illinois 60196
|
|||||
1 |
United States
|
|||||
1 | Telephone Number |
847-5********
|
||||
1 | Fax Number |
847-5********
|
||||
1 |
L******@MotorolaSolutions.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TNF - Licensed Non-Broadcast Transmitter Held to Face | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | VHF Portable Radio | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Output power listed is rated conducted; maximum conducted output power is 6.0 W as allowed by 47 CFR 90.205(s). Output is at the antenna terminal of the device and must not exceed that tested for SAR compliance. This transmitter may operate with the antennas tested for this filing in push-to-talk held-near-face and body-worn configurations. Body-worn SAR compliance is limited to the specific belt-clip and audio accessory configurations tested for this filing, and to belt-clips, holsters, or similar accessories that have no metallic component in the assembly and which provide at least 2.3 cm separation between the device, including its antenna, and the users body. This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50 %. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration to comply with Occupational/Controlled SAR limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements, and users must be provided with the training information. The highest reported SAR values for FCC-authorized operations accounting for a 50 % duty factor, are: head 1.11 W/kg, body 1.66 W/kg. Note 1: 11K0F3E, 7K60F1E, 7K60F1D, 7K60F1W, 7K60FXE, 7K60FXD | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Timco Engineering, Inc.
|
||||
1 | Name |
B******** C********
|
||||
1 | Telephone Number |
352-4********
|
||||
1 | Fax Number |
352 4********
|
||||
1 |
b******@timcoengr.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 80,90,90.210,90.210(e) | BE EF | 136.00000000 | 174.00000000 | 5.0000000 | 1.5000000000 ppm | NOTE 1 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC