FCC ID: AZ489FT5876 2-Way Portable Radio (with Bluetooth and Bluetooth LE)

 

Mobile Release 17.0 MTP3500 Feature User Guide OCTOBER 2018 2018 Motorola Solutions, Inc. All rights reserved

*MN001488A01*

MN001488A01-BF (en-US) DRAFT MN001488A01-BF (en-US) Contents Contents List of Figures............................................................................................................12 List of Tables............................................................................................................. 13 Declaration of Conformity........................................................................................ 14 Safety Information.....................................................................................................15 Notice to Users (FCC and Industry Canada)...........................................................16 Copyrights................................................................................................................. 17 General Information.................................................................................................. 18 1.1 Icon Conventions...................................................................................................................18 1.2 Using this Guide.................................................................................................................... 18 1.3 Feature and Service Availability............................................................................................ 18 Getting Started.......................................................................................................... 19 2.1 Product Technical Information............................................................................................... 19 2.2 Before Power On................................................................................................................... 20 2.2.1 Attaching the Antenna..............................................................................................20 2.2.2 Inserting the SIM Card............................................................................................. 21 2.2.3 Installing the Battery................................................................................................ 22 2.2.4 Removing the Battery.............................................................................................. 22 2.2.5 Charging the Battery................................................................................................ 22 2.2.6 Battery Charging Indications....................................................................................23 2.2.7 Low Battery Indication..............................................................................................23 2.3 Controls and Indicators..........................................................................................................23 2.4 Display...................................................................................................................................26 2.4.1 Configurable Idle Screen......................................................................................... 27 2.5 Status Icons...........................................................................................................................28 2.6 Powering On the Radio..........................................................................................................31 2.7 PIN Code Authentication....................................................................................................... 31 2.7.1 Unlocking Your Radio.............................................................................................. 32 2.7.2 Unblocking Your Radio............................................................................................ 32 2.8 Locking or Unlocking the Keys or Buttons............................................................................. 32 2.9 Holding Your Radio................................................................................................................32 2.10 High or Low Audio Toggle................................................................................................... 33 2.10.1 Using High Audio................................................................................................... 33 2.10.2 Using Low Audio.................................................................................................... 33 2.11 During a Call........................................................................................................................34 2.12 Entering TMO or DMO Mode...............................................................................................34 2 DRAFT MN001488A01-BF (en-US) Contents 2.13 Selecting Talkgroups........................................................................................................... 34 2.13.1 Talkgroup Icons Selection......................................................................................34 2.14 One-Touch Buttons..............................................................................................................36 Modes.........................................................................................................................39 3.1 Trunked Mode Operation.......................................................................................................39 3.1.1 Entering TMO Mode.................................................................................................39 3.1.2 Making Group Calls in TMO.....................................................................................39 3.1.3 Receiving Group Calls in Idle...................................................................................40 3.1.4 Receiving Group Calls during Ongoing Group Calls................................................40 3.1.5 Dynamic Group Number Assignment (DGNA).........................................................40 3.1.5.1 DGNA Reception........................................................................................40 3.1.5.2 DGNA Auto Select Group.......................................................................... 41 3.1.5.3 DGNA Auto Reselect Group...................................................................... 41 3.1.5.4 Viewing DGNA Talkgroups........................................................................ 41 3.1.6 Broadcast Call..........................................................................................................41 3.1.6.1 Broadcast Calls Initiated by Users............................................................. 41 3.1.6.2 Initializing Broadcast Calls......................................................................... 41 3.1.7 Phone and Private Automatic Branch Exchange (PABX) Calls............................... 42 3.1.8 Assistance Call........................................................................................................ 42 3.1.9 Call Modification.......................................................................................................42 3.2 Local Site Trunking................................................................................................................42 3.2.1 Entering Local Site Trunking....................................................................................43 3.2.2 Exiting Local Site Trunking...................................................................................... 43 3.3 Direct Mode Operation...........................................................................................................44 3.3.1 Entering DMO Mode................................................................................................ 44 3.3.2 Making Group Calls in DMO.................................................................................... 44 3.3.3 Receiving Group Calls in Idle...................................................................................44 3.3.4 Selecting DMO Communications Options................................................................45 3.3.5 DMO Private Priority Call......................................................................................... 45 3.3.6 Talkgroup for Individual Calls...................................................................................45 3.3.7 Network Monitor.......................................................................................................46 3.3.7.1 Enabling Network Monitor.......................................................................... 46 3.3.8 Communication through Repeaters......................................................................... 47 3.3.9 Communication through Gateways..........................................................................47 3.3.10 Gateway and Repeater Synchronization............................................................... 48 3.4 Transmit Inhibit Mode............................................................................................................ 48 3.5 Emergency Operations.......................................................................................................... 49 3.5.1 Emergency Alarm.................................................................................................... 49 3.5.2 Emergency Group Call.............................................................................................50 3 DRAFT MN001488A01-BF (en-US) Contents 3.5.2.1 Making Emergency Group Calls................................................................ 50 3.5.2.2 Receiving Emergency Group Calls............................................................ 50 3.5.3 Non-Tactical Emergency..........................................................................................51 3.5.4 Emergency Individual Calls (Private or MSISDN)....................................................51 3.5.5 Emergency SDS Status........................................................................................... 51 3.5.6 Emergency Hot Microphone.................................................................................... 51 3.5.7 Alternating Hot Microphone..................................................................................... 51 3.5.8 Silent Emergency Mode...........................................................................................52 3.5.9 Invisible Emergency.................................................................................................52 3.5.10 Emergency Alert.................................................................................................... 53 3.5.11 Disaster Alert......................................................................................................... 53 3.5.11.1 Initializing Disaster Alert Calls..................................................................54 3.5.12 Exiting Emergency Operations.............................................................................. 54 3.6 Repeater Mode......................................................................................................................54 Main Menu..................................................................................................................56 4.1 Scrolling through the Menu....................................................................................................56 4.2 Menu Icons............................................................................................................................ 56 4.3 Messages.............................................................................................................................. 57 4.3.1 New Message.......................................................................................................... 57 4.3.1.1 Sending Messages to Private/Phone......................................................... 58 4.3.1.2 Sending Messages to Groups....................................................................58 4.3.1.3 Sending Store and Forward Messages......................................................58 4.3.1.4 Delivery Report.......................................................................................... 59 4.3.2 Inbox........................................................................................................................ 60 4.3.2.1 Entering the Inbox...................................................................................... 61 4.3.2.2 Receiving New Messages..........................................................................61 4.3.2.3 Using Submenus in the Inbox and the Outbox...........................................61 4.3.2.4 Embedded Number.................................................................................... 62 4.3.2.5 Storing Numbers from Messages...............................................................62 4.3.2.6 Calling Numbers in Messages................................................................... 62 4.3.2.7 Making Group Calls on the Talkgroup of the Message Sender................. 63 4.3.2.8 Immediate Message...................................................................................63 4.3.3 Outbox..................................................................................................................... 63 4.3.4 Call-Out (CO) Box....................................................................................................64 4.3.4.1 Call-Out Icons............................................................................................ 64 4.3.5 Wireless Application Protocol (WAP) Box................................................................64 4.3.6 Templates................................................................................................................ 64 4.3.6.1 Sending User-Defined Templates.............................................................. 64 4.3.6.2 Managing User-Defined Templates........................................................... 65 4 DRAFT MN001488A01-BF (en-US) Contents 4.3.7 Predefined Templates..............................................................................................65 4.3.7.1 Viewing Predefined Templates.................................................................. 65 4.3.7.2 Sending Predefined Templates..................................................................65 4.3.8 Status Messages..................................................................................................... 66 4.3.8.1 Viewing a Status Message Number........................................................... 66 4.3.8.2 Sending Status Messages......................................................................... 66 4.3.8.3 Targeted Status Messages........................................................................ 66 4.3.9 Sending an RMS Status...........................................................................................67 4.3.10 Additional Address................................................................................................. 67 4.3.10.1 Enabling or Disabling Additional Address................................................ 67 4.3.10.2 Selecting Additional Address................................................................... 68 4.3.10.3 Viewing Additional Address......................................................................68 4.3.10.4 Entering New Additional Address.............................................................68 4.3.10.5 Editing Additional Address....................................................................... 68 4.3.10.6 Deleting Additional Address..................................................................... 69 4.3.11 Call-Out Availability................................................................................................69 4.3.11.1 Setting Call-Out Availability......................................................................69 4.4 Contacts.................................................................................................................................69 4.4.1 Creating Contacts.................................................................................................... 70 4.4.2 Editing Contacts.......................................................................................................71 4.4.3 Deleting Numbers.................................................................................................... 71 4.4.4 Deleting Contacts.....................................................................................................71 4.4.5 Checking Capacity................................................................................................... 72 4.4.6 Dialing through the Contact List...............................................................................72 4.5 Bluetooth................................................................................................................................72 4.5.1 Bluetooth Settings....................................................................................................72 4.5.1.1 Configuring Bluetooth Settings...................................................................72 4.5.2 Enabling and Disabling Bluetooth............................................................................ 73 4.5.3 Pairing Bluetooth Devices with Your Radio............................................................. 73 4.5.4 Devices.................................................................................................................... 74 4.5.4.1 Connecting or Disconnecting Devices....................................................... 74 4.5.4.2 Managing Devices......................................................................................74 4.5.5 Disconnecting All Devices........................................................................................75 4.5.6 Setting Indoor Location............................................................................................ 75 4.5.6.1 Viewing Detected Beacon.......................................................................... 75 4.5.7 Connecting Firearms Devices..................................................................................76 4.6 Browser..................................................................................................................................76 4.7 Man Down..............................................................................................................................76 4.7.1 Setting Man Down....................................................................................................77 5 DRAFT MN001488A01-BF (en-US) Contents 4.8 Security..................................................................................................................................77 4.8.1 PIN Protect...............................................................................................................77 4.8.1.1 Protecting the Radio with a PIN Code........................................................77 4.8.1.2 Changing PIN Codes................................................................................. 77 4.8.2 Setting Keypad Lock................................................................................................ 78 4.8.2.1 Keypad Lock Notification............................................................................78 4.8.2.2 Setting Automatic Keylock Delay............................................................... 78 4.8.2.3 Setting Keylock on Startup.........................................................................78 4.8.3 Air Encryption...........................................................................................................78 4.8.3.1 Viewing Air Encryption State......................................................................79 4.8.3.2 Deleting User Keys.................................................................................... 79 4.8.4 K Validity.................................................................................................................. 79 4.8.4.1 Verifying K Validity..................................................................................... 79 4.8.5 SCK (Air Interface Encryption Class 2)....................................................................80 4.8.5.1 TMO SCK...................................................................................................80 4.8.5.2 DMO SCK.................................................................................................. 80 4.8.5.3 Changing DMO SCK.................................................................................. 81 4.8.6 Covert Mode............................................................................................................ 81 4.8.6.1 Activating Covert Mode.............................................................................. 81 4.8.6.2 Setting Vibrate in Covert Mode.................................................................. 82 4.8.7 Remote Control........................................................................................................82 4.8.7.1 Status Remote Control...............................................................................82 4.8.7.2 SDS Remote Control..................................................................................83 4.8.7.3 Setting Remote Control..............................................................................83 4.9 Setup..................................................................................................................................... 83 4.9.1 Vibrate......................................................................................................................83 4.9.1.1 Setting Default Vibrate............................................................................... 83 4.9.1.2 Setting Detail Vibrate................................................................................. 84 4.9.2 Ring Style.................................................................................................................84 4.9.2.1 Setting Ring Style.......................................................................................84 4.9.3 Set Volume.............................................................................................................. 84 4.9.3.1 Setting Volume...........................................................................................85 4.9.4 Language.................................................................................................................85 4.9.4.1 Setting Language....................................................................................... 85 4.9.5 Data Setup............................................................................................................... 85 4.9.5.1 Setting Data Function.................................................................................86 4.9.6 Audio........................................................................................................................86 4.9.6.1 Audio Profiles............................................................................................. 86 4.9.6.2 Howling Suppression................................................................................. 86 6 DRAFT MN001488A01-BF (en-US) Contents 4.9.6.3 Audio Toggle.............................................................................................. 87 4.9.6.4 Volume Adjustment Mode.......................................................................... 87 4.9.7 Tones....................................................................................................................... 88 4.9.7.1 Keypad Tone..............................................................................................88 4.9.7.2 All Tones.................................................................................................... 88 4.9.7.3 Talk Permit................................................................................................. 88 4.9.7.4 Clear to Send............................................................................................. 89 4.9.7.5 Periodic Alert..............................................................................................89 4.9.7.6 D-PTT Tones..............................................................................................89 4.9.8 Display..................................................................................................................... 90 4.9.8.1 Setting Flip Display.................................................................................... 90 4.9.8.2 Setting Font Level...................................................................................... 90 4.9.8.3 Setting Large Idle Font...............................................................................91 4.9.8.4 Setting Screen Saver................................................................................. 91 4.9.8.5 Setting Backlight........................................................................................ 91 4.9.8.6 Setting Brightness...................................................................................... 92 4.9.8.7 Setting LCD Off.......................................................................................... 92 4.9.8.8 Setting Wallpaper.......................................................................................92 4.9.9 Time and Date......................................................................................................... 92 4.9.9.1 Setting the Time Format.............................................................................93 4.9.9.2 Setting the Time Manually..........................................................................93 4.9.9.3 Setting the Date Format............................................................................. 93 4.9.9.4 Setting the Date Manually.......................................................................... 93 4.9.9.5 Setting Time Offset.................................................................................... 94 4.9.9.6 Setting Automatic Updates for the Time and Date ....................................94 4.9.10 Energy Economy....................................................................................................94 4.9.10.1 Enabling or Disabling Energy Economy...................................................94 4.9.10.2 Viewing the Energy Economy Status....................................................... 94 4.9.11 Transmission Power Class.................................................................................... 95 4.9.11.1 Selecting RF Power................................................................................. 95 4.9.12 Accessory (Accry) Setup........................................................................................95 4.9.12.1 Selecting CORE/Other/Secondary Accessories...................................... 95 4.9.13 Book On................................................................................................................. 96 4.9.14 Rotary Knob........................................................................................................... 96 4.9.14.1 Setting Rotary Lock..................................................................................96 4.9.14.2 Setting In Keypad Lock............................................................................ 96 4.9.14.3 Setting Rotary Knob Wrap Around...........................................................97 4.9.14.4 Setting Rotary Knob Scroll Range........................................................... 97 4.9.14.5 Setting Rotary Knob Talkgroup Selection................................................ 97 7 DRAFT MN001488A01-BF (en-US) Contents 4.9.14.6 Setting Rotary Knob Function Keys......................................................... 97 4.9.15 Default Setting....................................................................................................... 98 4.9.15.1 Selecting Default Setting..........................................................................98 4.10 Group Setup........................................................................................................................ 98 4.10.1 Setting Operations Parameters..............................................................................98 4.10.1.1 Standard Home Group............................................................................. 99 4.10.2 Scan.......................................................................................................................99 4.10.2.1 Activating Talkgroup Scanning.................................................................99 4.10.2.2 Setting Talkgroups in the Active Scan List...............................................99 4.10.2.3 Setting Scan Lists.................................................................................. 100 4.10.2.4 Deleting Talkgroups from Scan Lists..................................................... 100 4.10.3 My Groups........................................................................................................... 100 4.10.3.1 Adding Favorite Folders......................................................................... 100 4.10.3.2 Adding Talkgroups to Favorite Folders.................................................. 100 4.10.3.3 Deleting Favorite Folders....................................................................... 101 4.10.3.4 Deleting Talkgroup from Favorite Folders..............................................101 4.11 Individual Setup................................................................................................................. 101 4.11.1 Trunked Mode......................................................................................................101 4.11.1.1 Enabling or Disabling Call Waiting......................................................... 101 4.11.1.2 Setting Call Forwarding..........................................................................102 4.12 Favorites............................................................................................................................102 4.12.1 Adding Folders to Favorites................................................................................. 102 4.12.2 Adding Contact Numbers to Favorites................................................................. 102 4.12.3 Making Private Calls to Favorite Contact Numbers............................................. 103 4.12.4 Adding Talkgroups to Favorites........................................................................... 103 4.12.5 Managing Folders in Favorites.............................................................................103 4.12.6 Deleting Folders in Favorites............................................................................... 104 4.12.7 Deleting Items from Favorites Folder...................................................................104 4.12.8 Deleting All Items from Favorite Folders..............................................................104 4.13 My Info...............................................................................................................................105 4.13.1 Viewing Personal Information.............................................................................. 105 4.14 Recent Calls...................................................................................................................... 105 4.14.1 Viewing Recent Calls........................................................................................... 105 4.14.2 Calling from Recent Calls.................................................................................... 106 4.14.3 Storing Recent Calls to Contacts......................................................................... 106 4.14.4 Deleting Recent Calls.......................................................................................... 107 4.15 Networks............................................................................................................................107 4.15.1 Selecting Network Operation Mode..................................................................... 107 4.15.2 Network Select.....................................................................................................108 8 DRAFT MN001488A01-BF (en-US) Contents 4.15.2.1 Selecting Your Network..........................................................................108 4.15.2.2 Using Select Net Registration................................................................ 108 4.15.3 Talkgroup Network Select....................................................................................108 4.15.3.1 Selecting Your Talkgroup Network.........................................................108 4.15.3.2 Using Select TG Net Registration.......................................................... 108 4.15.3.3 Using Prefer TG Net Registration.......................................................... 109 4.15.3.4 Using Any TG Net Registration.............................................................. 109 4.16 Location............................................................................................................................. 109 4.16.1 Enabling GNSS....................................................................................................109 4.16.2 Viewing Your Position.......................................................................................... 110 4.16.3 Viewing Testpage................................................................................................ 110 4.16.4 Changing GNSS Accuracy...................................................................................110 4.16.5 Backlog................................................................................................................ 111 4.16.5.1 Enabling or Disabling Backlog............................................................... 111 4.16.5.2 Viewing Backlog Reports....................................................................... 111 4.16.5.3 Deleting All Backlog Reports..................................................................111 4.17 Packet Data....................................................................................................................... 111 4.17.1 Viewing Data Statistics........................................................................................ 112 4.17.2 Viewing Encryption Status................................................................................... 112 4.18 Crypto Menu...................................................................................................................... 112 4.18.1 Enabling or Disabling SIM Card End-to-End Encryption......................................112 4.18.2 Setting Clear Call Alarm.......................................................................................113 4.18.3 Updating Encryption Keys....................................................................................113 4.18.4 Viewing OPTA......................................................................................................114 4.18.5 Setting OPTA Filter.............................................................................................. 114 4.18.6 Starting Crypto Registration.................................................................................114 4.18.7 Configuring Audio Settings.................................................................................. 114 4.18.8 Setting DMO Encryption Mode............................................................................ 114 4.18.9 Setting Encryption Keys for SDS Messages........................................................115 Features................................................................................................................... 116 5.1 Ambience Listening (AL) Call.............................................................................................. 116 5.2 Bluetooth..............................................................................................................................116 5.2.1 Bluetooth Interactions............................................................................................ 117 5.2.2 Discoverable Mode................................................................................................ 117 5.2.3 Add Bluetooth Devices...........................................................................................117 5.2.4 Bluetooth Smart Proximity Pairing......................................................................... 117 5.2.5 Bluetooth Sensor Data...........................................................................................118 5.3 Buffer Full Overwrite Policy................................................................................................. 118 5.4 Call-Out................................................................................................................................118 9 DRAFT MN001488A01-BF (en-US) Contents 5.4.1 Types of Call-Out Alerts.........................................................................................119 5.4.2 Call-Out Modes Interaction.................................................................................... 120 5.4.3 Call-Out Service Phases........................................................................................120 5.5 Collaborative Messaging..................................................................................................... 121 5.6 Dialing through Soft Numeric Keypad..................................................................................121 5.7 Global Navigation Satellite System (GNSS) Location Service............................................ 121 5.7.1 Enhance GNSS Performance................................................................................ 122 5.7.2 Location Report Backlog........................................................................................123 5.7.3 GNSS Icon............................................................................................................. 123 5.7.4 Different Location Displays.................................................................................... 123 5.7.5 GNSS Accuracy..................................................................................................... 124 5.8 Home Display Text Message...............................................................................................124 5.9 MS-ISDN..............................................................................................................................124 5.10 Private Call........................................................................................................................ 124 5.10.1 Making Private Calls............................................................................................ 125 5.11 Phone and Private Automatic Branch Exchange (PABX) Calls.........................................125 5.11.1 Making Phone or PABX Calls.............................................................................. 125 5.12 Phone/PABX Speed Dial................................................................................................... 125 5.12.1 Using the Phone/PABX Speed Dial..................................................................... 126 5.13 Radio Messaging System (RMS).......................................................................................126 5.13.1 RMS Icons........................................................................................................... 126 5.14 Radio User Assignment (RUA) and Radio User Identity (RUI)..........................................127 5.15 SIM Card End-to-End Encryption...................................................................................... 127 5.16 Short Number Dial............................................................................................................. 128 5.17 Talkgroup Dialing by Index................................................................................................ 128 5.18 Terminal Permanent Disable............................................................................................. 129 5.19 Terminal Temporary Disable or Enable............................................................................. 129 5.20 Writing Text........................................................................................................................129 5.20.1 Text Entry Icons................................................................................................... 129 5.20.2 Keys Usage..........................................................................................................130 5.21 Wireless Application Protocol (WAP).................................................................................130 5.21.1 WAP Browser.......................................................................................................130 5.21.2 Entering the Browser........................................................................................... 131 5.21.3 Entering Browser Menu Panes............................................................................ 131 5.21.4 Tips for Browsing................................................................................................. 131 5.21.4.1 Creating Bookmarks through the Navigate Pane...................................131 5.21.4.2 Creating Bookmarks through the Bookmarks Pane............................... 131 5.21.4.3 Using Bookmarks................................................................................... 132 5.21.4.4 Saving Pages......................................................................................... 132 10 DRAFT MN001488A01-BF (en-US) Contents 5.21.4.5 Selecting Saved Pages.......................................................................... 132 5.21.5 Disabled Packet Data Service............................................................................. 132 5.21.6 Disabled Browser Entry....................................................................................... 133 5.21.7 Browser Keys Usage........................................................................................... 133 5.21.8 Browser Menu Panes Overview...........................................................................134 5.21.9 Navigate Pane..................................................................................................... 134 5.21.10 Advanced...........................................................................................................135 5.21.11 Bookmarks Pane................................................................................................135 5.21.11.1 Working with the Options Pane for Selected Bookmarks.....................135 5.21.11.2 Working with the Saved Pages Folder................................................. 136 5.21.12 History Pane...................................................................................................... 136 5.21.12.1 Navigating to Recently Visited URLs................................................... 136 5.21.13 Tools Pane.........................................................................................................137 5.21.14 Options Pane..................................................................................................... 137 5.21.15 Text Input Pane..................................................................................................137 5.21.16 WAP Push..........................................................................................................138 5.21.16.1 New WAP Messages........................................................................... 138 5.21.16.2 Viewing WAP Messages...................................................................... 138 Appendix A: Tones..................................................................................................139 Appendix B: LED Indications.................................................................................141 Appendix C: Troubleshooting................................................................................142 Appendix D: Maintenance...................................................................................... 145 D.1 Storage................................................................................................................................145 D.2 Extending Battery Life.........................................................................................................145 D.3 Battery Charging Temperature............................................................................................145 D.4 Additional Battery Warnings/Cautions.................................................................................145 D.5 Looking after Your Radio.................................................................................................... 146 11 DRAFT MN001488A01-BF (en-US) List of Figures List of Figures Figure 1: Charger Mode Screen.............................................................................................................23 Figure 2: Default Home Screen with Icons............................................................................................. 26 Figure 3: Trunked Mode Operation........................................................................................................ 39 Figure 4: Direct Mode Operation............................................................................................................ 44 Figure 5: Communication through Repeaters.........................................................................................47 Figure 6: Communication through Gateways......................................................................................... 47 Figure 7: Repeater Mode Operation.......................................................................................................55 Figure 8: Call-Out Message..................................................................................................................119 12 DRAFT MN001488A01-BF (en-US) List of Tables List of Tables Table 1: Special Notations......................................................................................................................18 Table 2: Product Technical Information..................................................................................................19 Table 3: Battery Icons.............................................................................................................................23 Table 4: Controls and Indicators.............................................................................................................24 Table 5: Display......................................................................................................................................26 Table 6: Colors of the Soft Key Area......................................................................................................27 Table 7: Status Icons..............................................................................................................................28 Table 8: During the Call..........................................................................................................................34 Table 9: Talkgroup Icons........................................................................................................................35 Table 10: One-Touch Button Features ..................................................................................................36 Table 11: Emergency Operation Dependencies.....................................................................................53 Table 12: Menu Icons.............................................................................................................................56 Table 13: Inbox Icons............................................................................................................................. 60 Table 14: Outbox Icons.......................................................................................................................... 63 Table 15: Call-Out Icons.........................................................................................................................64 Table 16: Contact Types........................................................................................................................ 70 Table 17: Different Location Displays...................................................................................................123 Table 18: RMS Icons............................................................................................................................126 Table 19: Radios Interactions...............................................................................................................128 Table 20: Text Entry Screen Icons....................................................................................................... 129 Table 21: Keys Usage.......................................................................................................................... 130 Table 22: Browser Keys Interactions....................................................................................................133 Table 23: Browser Menu Panes........................................................................................................... 134 Table 24: Additional Menu Panes.........................................................................................................134 Table 25: Browser Text Input Icons......................................................................................................137 Table 26: Radio Tones......................................................................................................................... 139 Table 27: LED Status Indications......................................................................................................... 141 Table 28: Battery Charging LED Indications........................................................................................ 141 Table 29: Displayed Messages............................................................................................................ 142 13 DRAFT MN001488A01-BF (en-US) Declaration of Conformity Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. Declaration of Conformity Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola Solutions, Inc. Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A. Phone Number: 1-800-927-2744 Hereby declares that the product:

Model Name: MTP3500 conforms to the following regulations:

FCC Part 15, subpart B, section 15.107(a), 15.107(d), and section 15.109(a) Class B Digital Device As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the follow-

ing two conditions:

1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause unde-

sired operation. NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and Industry Canada license-ex-

empt RSS standard. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the in-

structions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the re-

Increase the separation between the equipment and receiver. ceiver is connected. Consult the dealer or an experienced radio or TV technician for help. 14 DRAFT MN001488A01-BF (en-US) Safety Information Safety Information RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios ATTENTION!

This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. For a list of Motorola Solutions-approved antennas, batteries, and other accessories, visit the following website:

http://www.motorolasolutions.com Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter has been approved by Industry Canada to operate with Motorola Solutions-

approved antenna with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. 15 DRAFT MN001488A01-BF (en-US) Notice to Users (FCC and Industry Canada) Notice to Users (FCC and Industry Canada) This device complies with Part 15 of the FCC rules and Industry Canada's license-exempt RSS's per the following conditions:

This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this device, not expressly approved by Motorola Solutions, could void the authority of the user to operate this equipment. 16 DRAFT MN001488A01-BF (en-US) Copyrights Copyrights The Motorola Solutions products described in this document may include copyrighted Motorola Solutions computer programs. Laws in the United States and other countries preserve for Motorola Solutions certain exclusive rights for copyrighted computer programs. Accordingly, any copyrighted Motorola Solutions computer programs contained in the Motorola Solutions products described in this document may not be copied or reproduced in any manner without the express written permission of Motorola Solutions. 2018 Motorola Solutions, Inc. All Rights Reserved No part of this document may be reproduced, transmitted, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without the prior written permission of Motorola Solutions, Inc. Furthermore, the purchase of Motorola Solutions products shall not be deemed to grant either directly or by implication, estoppel or otherwise, any license under the copyrights, patents or patent applications of Motorola Solutions, except for the normal non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product. Disclaimer Please note that certain features, facilities, and capabilities described in this document may not be applicable to or licensed for use on a specific system, or may be dependent upon the characteristics of a specific subscriber unit or configuration of certain parameters. Please refer to your Motorola Solutions contact for further information. Trademarks MOTOROLA, MOTO, MOTOROLA SOLUTIONS, and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. European Union (EU) Waste of Electrical and Electronic Equipment (WEEE) directive The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries should not dispose of electronic and electrical equipment or accessories in household waste. Customers or end-users in EU countries should contact their local equipment supplier representative or service centre for information about the waste collection system in their country. 17 DRAFT MN001488A01-BF (en-US) General Information General Information 1.1 Icon Conventions The documentation set is designed to give the reader more visual clues. The following graphic icons are used throughout the documentation set. DANGER: The signal word DANGER with the associated safety icon implies information that, if disregarded, will result in death or serious injury. WARNING: The signal word WARNING with the associated safety icon implies information that, if disregarded, could result in death or serious injury, or serious product damage. CAUTION: The signal word CAUTION with the associated safety icon implies information that, if disregarded, may result in minor or moderate injury, or serious product damage. CAUTION: The signal word CAUTION may be used without the safety icon to state potential damage or injury that is not related to the product. IMPORTANT: IMPORTANT statements contain information that is crucial to the discussion at hand, but is not CAUTION or WARNING. There is no warning level associated with the IMPORTANT statement. NOTICE: NOTICE contains information more important than the surrounding text, such as exceptions or preconditions. They also refer the reader elsewhere for additional information, remind the reader how to complete an action (when it is not part of the current procedure, for instance), or tell the reader where something is on the screen. There is no warning level associated with a notice. 1.2 Using this Guide The following special notations are used throughout the text to highlight certain information or items:

Table 1: Special Notations Example Menu key or PTT button Entering TMO tone Powering Off Setup Tones All Tones Description Bold words indicate a name of a key, button, or soft menu item. Italic words indicate a name of the tone. Typewriter words indicate the MMI strings or messages displayed on the radio. Bold words with the arrow between indicate navigation structure in the menu items. 1.3 Feature and Service Availability This guide describes all available radio features and services. Your service provider may have customized your radio to optimize its use for your individual needs. Check with your service provider to find out the differences from this guide. 18 DRAFT MN001488A01-BF (en-US) Getting Started Getting Started This chapter contains basic information on how to use the radio. 2.1 Product Technical Information 1 or 1.8 W (switchable) 2 W at 16 4.7 A Value 4.2 V Table 2: Product Technical Information Description Maximum Voltage Maximum Current Maximum RF Power Maximum Speaker Load Antenna Impedance Operating Tempera-

ture Range Storage Temperature Range Ingress Protection Rating Audio Power Through the Radio and Acces-

sories Operating Time 50 Duty Cycle

-30 C to +60 C 20 C to 30C IP65, IP66, and IP67 RMS: 2 W Peak Power: 4 W Class 4 (1 W) Class 3L (1.8 W) Standard 1650 mAh Battery 2150 mAh Battery 3400 mAh Battery 05/05/90 05/35/60 05/05/90 05/35/60 05/05/90 05/35/60

> 16 h

> 12 h

> 21 h

> 16 h

> 30 h

> 22 h

> 15 h

> 11 h

> 20 h

> 15 h

> 28 h

> 21 h Enhanced Data Trans-

fer Hardware ready for TETRA Enhanced Data Service (TEDS) NOTICE: 800 MHz models are not hardware ready for TEDS. 19 DRAFT MN001488A01-BF (en-US) Getting Started NOTICE:

The system (SwMI) determines radio transmit and receive times, which affect the actual radio operating time. If the radio overheats (due to high ambient temperature or other factors), thermal protection will reduce transmitter power, which may lead to loss of communication. You can attach a colorful o-ring to a radio antenna to distinguish radios from one another. An RFID knob is available as an optional accessory which allows tracking radios easily. The knob contains an RFID tag which can be read by handheld scanners greatly enhancing the speed of radio identification. The knob is a retrofit option and can replace an existing volume knob. 2.2 Before Power On Read this section before you power on your radio for the first time. 2.2.1 Attaching the Antenna Procedure:

1 Insert the screw-in base of the antenna into the antenna terminal on the top of the radio. 2 Turn clockwise until tight. IMPORTANT: Use only the antenna intended for the radio. Make sure that the antenna has an operating frequency engraving and a color ring at the bottom of the thread. Use of other antennas can result in significant range loss due to poor RF performance. 20 DRAFT MN001488A01-BF (en-US) Getting Started 2.2.2 Inserting the SIM Card NOTICE: MTP3500 800MHz and MTP3550 800 MHz are not fitted with a SIM latch. Prerequisites: Turn off your radio before inserting the SIM card. Procedure:

1 Remove the battery. 2 Open a plastic SIM card cover. 3 Slide a SIM card latch towards the bottom of the radio and lift the latch. 4 Place the SIM card in a socket with the contact area facing down. Pay attention to the correct position of the notched corner. 5 Close the SIM card latch and slide it towards the top of the radio. 6 Close the plastic SIM card cover. 7 Replace the battery. 21 DRAFT MN001488A01-BF (en-US) Getting Started 2.2.3 Installing the Battery Procedure:

1 Insert the battery into the compartment. 2 Slide the battery towards the top of the radio until it clicks. 2.2.4 Removing the Battery Prerequisites: Turn off the radio. Procedure:

1 Push up and hold the latch at the bottom of the battery. 2 Slide the battery toward the bottom of the radio. 2.2.5 Charging the Battery You can charge a battery separately or attached to a radio. Charging a battery attached to a radio must be done with the radio turned off. The battery charges faster when the radio is turned off. IMPORTANT: Use only Motorola Solutions approved-chargers which provide optimal performance. Using other chargers may fail to fully charge, or reduce the life of the battery. Prerequisites:

Do not charge the battery in a hazardous area. IMPORTANT: Do not connect a radio without a battery to the charger. Procedure:

1 Connect the charger to an appropriate power source, according to the specification of the charger. 2 Perform one of the following actions:

Desktop chargers insert the battery or the radio with the battery attached into the appropriate socket of the charger. Ensure that the battery/radio made good connection with the charger and that the LED on the charger is indicating that charging is in progress. Travel chargers and car chargers connect the charger to the radio with the battery attached. Ensure that the charger is firmly connected to the radio and that the radio display is indicating that charging is in progress. 22 DRAFT MN001488A01-BF (en-US) Getting Started NOTICE: If a multi-unit charger LED indicates an error (blinking red light) when radio is inserted and being charged with the multi-unit charger (MUC), re-insert the radio. If the light is still red after several reconnections to MUC, the battery may be damaged or reached its end of life. Postrequisites: The battery may heat up during charging. After charging, make sure that the battery and the radio are within the operating temperature range before using the radio. 2.2.6 Battery Charging Indications When the radio is charging, it displays the Charger Mode screen. The screen displays an appropriate Battery Charge Progress icon and charging progress expressed in percentage. NOTICE:

To easily identify the charging status, check the Battery Charging LED Indicator. See LED Indications on page 141. Figure 1: Charger Mode Screen Table 3: Battery Icons Battery Capacity 0%5%

5%15%

15%25%

25%40%

40%60%

60%80%

Battery Charge Progress 0%5%

5%15%

15%25%

25%40%

40%60%

60%80%

80%

100%

80%

100%

2.2.7 Low Battery Indication The radio indicates low battery level by playing an audible alert when the battery charge falls to a preset level. The low battery alert can be programmed to be 5, 10, or 20 % of remaining capacity by your service provider. The default setting is 5 %. The service provider also configures how frequently the alert repeats. 2.3 Controls and Indicators 23 Charger ModeCharging:35%DRAFT MN001488A01-BF (en-US) Getting Started Table 4: Controls and Indicators Annotation 1 Description Talkgroup Knob Rotate to select a different talkgroup. Volume Knob 2 24 57381091165421141671715131218DRAFT Annotation Description Rotate to set the volume. MN001488A01-BF (en-US) Getting Started 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Top Microphone Activated during Simplex, high audio calls such as Group Calls. LED Programmable Side button Programmable button, by default, the upper Programmable Side button is set to the Flip Display feature and the lower Programmable Side button is set to the Hi/Low Audio feature. NOTICE: The required time to press and hold Programmable Side button to activate a One-Touch Button feature is set as default to 0,1 second. Push-To-Talk (PTT) Press and hold to talk in simplex calls or to initiate a group call, release it to listen. Press to send status and text messages. Soft key Press Left or Right Soft key, to select the option that appears on the screen directly above them. Send key Press to initiate or answer duplex calls, or send messages. Bottom Microphone Activated during Duplex, low audio calls such as Private Calls. Charger Connector Provides connection for programming and data transfer. Antenna Emergency button Press and hold Emergency button to enter Emergency operation. When your radio is off, press and hold to power on in Emergency Mode. Earpiece Activated during Duplex calls. Accessory Connector Provides connection for accessories. Display Provides alphanumeric text and images within 65,536 colors and 132x90 pixels with scalable fonts and contrast. NOTICE: The Display can be in color and grayscale mode. Menu key From the home screen, press to enter the main menu. Used to enter the context-sensitive menu. 25 DRAFT MN001488A01-BF (en-US) Getting Started Annotation 17 18 Description On/Off/End/Home key Press and hold to turn on/off your radio. Press to end calls. Press to return to the home screen. NOTICE: If a message or notification is displayed on the radio and the Screen Saver activates, pressing On/Off/End/Home only deactivates the Screen Saver. Navigation key Press Up, Down, Left or Right Navigation key for list scrolling, while moving around the menu hierarchy, or for alphanumeric text editing. From the home screen, press to activate one of the following:

Down Navigation key enters Recent Calls menu item. Up Navigation key changes My Groups talkgroup folder. Left and Right Navigation key toggles through the talkgroups. NOTICE: A detailed list of compatible accessories is included in Accessory Leaflet, part number: 68015000843. To obtain the document, contact your service provider. 2.4 Display This section presents the default home screen elements of the radio. Figure 2: Default Home Screen with Icons Table 5: Display Annotation 1 2 3 4 Description Status icon area Text display area Soft key area Menu/Context sensitive icon 26 1234Home ModeNetworkRangeOptionsContcsDRAFT MN001488A01-BF (en-US) Getting Started The color of the Soft key area changes according to the mode the radio is in. Table 6: Colors of the Soft Key Area Color Light blue Light red Olive Yellow Red Green Blue Gray Mode or State Normal TMO and DMO Modes Emergency Mode or Disaster Alert Call Local Site Trunking Mode Call Out Standby Call Out Alert Call Out Accepted Radio Messaging Service (RMS) Radio User Assignment (RUA) Limited service 2.4.1 Configurable Idle Screen Your service provider can configure the information that is displayed on the idle screen below the status icon area. The displayed information depends on the radio configuration and services supported. Audio Profile Name BSI Registration Status Home Mode Network (No Service, or Mobile Country Code (MCC)/Mobile Network Code (MNC), or Networks Individual Short Subscriber Identity (ISSI) International Talkgroup Link Alias Alias) Operational-Tactical Address (OPTA) Radio Status Range RMS/FMS RMS messages Scan List Alias Secondary Talkgroup Alias Talkgroup Alias Time and Date Order and visibility of these items are also subject of the Configurable Idle Screen settings. 27 DRAFT MN001488A01-BF (en-US) Getting Started 2.5 Status Icons Status icons appear when your radio is engaged in certain activities or when you have activated certain features. Depending on the current mode, the size of the UI icons is reduced to allow for more lines of text to be entered. Table 7: Status Icons Icon Trunked Mode Operation (TMO) Description In Service No Service Signal Strength The more bars, the stronger the signal. RF Power Indicates that High RF Power is enabled. Shows the signal strength. The more bars, the stronger the signal. Migration Indicates that the radio is registered to a foreign network. Broadcast Call Indicates that the radio is in a Broadcast Call. Scan Indicates that talkgroup scanning is activated in the radio. Packet Data or Multi-Slot Packet Data (MSPD) The more blue sections on the icon, the faster the data transfer. Possible status:

Four gray sections: context activated data idle One blue: Packet Data active Two blue: Multi-Slot Packet Data active Direct Mode Operation (DMO) or Direct Mode Call Indicates that the radio is receiving a Direct Mode call. The more bars, the stronger the signal. High RF Power: idle or transmitting Indicates High RF Power option is enabled and the radio is either in idle mode or is transmitting a call. High RF Power: receiving Indicates High RF Power option is enabled and the ra-

dio is receiving a call. Direct Mode Indicates that radio is in Direct Mode (radio-to-radio communication). DMO Gateway Communication Mode Indicates that gateway is selected. The icon has the following status:

Solid when the radio is synchronized with the gateway. Blinking when the radio is not synchronized or during attachment. No icon during radio-to-radio and repeater communication. 28 DRAFT MN001488A01-BF (en-US) Getting Started Icon General Icons Description DMO Repeater Communication Mode Indicates that the Repeater or GW + Rep option in DMO Mode is selected. The icon has the following status:

Solid when the radio has detected the repeater (for example, when the radio receives a presence signal). Blinking when the radio has not detected the repeater or during attachment. No icon during a radio-to-radio and gateway communication. All Tones Off Indicates that:

Volume is set to 0 (when Volume Adj. Mode is set to Common). Both simplex and duplex ring volume is set to 0 (when Volume Adj. Mode is set to Individual). Simplex Ring Muted Indicates that simplex ring volume is set to 0 and duplex ring volume is set to more than 0. Duplex Ring Muted Indicates that duplex ring volume is set to 0 and simplex ring volume is set to more than 0. Low Audio Indicates that the audio mode is changed to low. High Audio Indicates that the audio mode is changed to high. Earpiece Connected Indicates that the earpiece is connected. GNSS Solid the radio has a location fix. Blinking the radio is acquiring a location fix. This feature is an optional setting and may not be enabled on your radio. Battery Strength Shows the charge of your battery. Battery Charging Indicates that the battery is charging. Emergency Indicates that the radio is in Emergency Operation. Solid Emergency Operations initiated. Blinking the radio is in emergency receiving state. Disaster Alert Call Indicates that the radio is in Disaster Alert Call. New Message Has Arrived Indicates that a new message has arrived. New Message in Inbox Indicates that you have unread messages in your Inbox. Unread (New) WAP Message Indicates that new page was loaded to the browser. Man Down Active Indicates that the Man Down feature is active. 29 DRAFT MN001488A01-BF (en-US) Getting Started Icon Description Man Down Alert Indicates that the Man Down feature is active. This icon has the following status:

Blinking pre-Alert; the radio signalizes Man Down conditions. To exit the pre-

Alert state, change the conditions or press the PTT button. Solid the radio enters Alert mode. Call-Out Indicates Call-Out alert. Call-Out Alert Arrived Indicates a receipt of a new Call-Out message. Call-Out Alert Unread Indicates unread alert in the CO Box. for the selected talkgroup, for the highlighted private number, for the manually entered private number, End-to-End Encryption (E2EE) Solid, when the E2EE is enabled:

when transmitting voice in Group Calls, when transmitting voice in Simplex Private Calls. Blinking, when the E2EE is enabled:

when receiving voice in Group Calls, when receiving voice in Simplex Private Calls, during encrypted Duplex Private Calls. Encryption Off Blinking Indicates that the SIM Card E2EE is disabled in DMO and TMO Modes. SIM End-to-End Encryption (E2EE) in TMO Indicates that the SIM Card E2EE is enabled in TMO Mode. or SIM End-to-End Encryption (E2EE) in DMO Indicates that the SIM Card E2EE is enabled in DMO Mode. Numbers 1 and 2 point to the type of DMO Encryption keys that has been selected. SDS End-to-End Encryption (E2EE) Indicates the E2EE status of an SDS message, or the E2EE status of a message recipient address. In High Security mode, when your radio processes only the encrypted information, this icon is always visible in when you are in the messages menu, for example, In-

box. Unread (New) WAP Message Indicates that you have not entered WAP Box since last WAP message was received. Blinks when the priority is high. WAP Message Icon Displayed next to the priority WAP message in the message list view. 30 DRAFT Icon Description WAP Message Time Displayed next to the create date in the message list view. MN001488A01-BF (en-US) Getting Started WAP Message Expiration Displayed next to the expiry date in the message list view. WAP Message Title Icon Displayed next to the title along with the text in the mes-

sage list view. Keys Locked Indicates that keys are locked. Bluetooth Connected Indicates that Bluetooth is enabled and at least one device is connected. Bluetooth Disconnected Solid Indicates that Bluetooth is enabled, but no device is connected. Blinking indicates one of the following:

- Bluetooth is enabled and the radio is in the Discoverable Mode.

- Bluetooth is enabled and a connection with a remote device is being estab-

lished. Remote Control Indicates that the radio is being remotely controlled and some commands are being executed in the background. For example, when the radio is being controlled by special SDS messages or triggered to send a GNSS location re-

port. 2.6 Powering On the Radio Procedure:

Press and hold On button. Your radio performs a self-check and registration routine. After successful registration, your radio is in service. NOTICE: Your radio powers on without visible and audible notification if Covert Mode is activated. 2.7 PIN Code Authentication If pre-set by your service provider, the radio has active PIN Code Authentication, which helps you increase security and protect your radio against unauthorized use. The PIN code is read from the SIM card or radio programming and cannot be changed or disabled. If you are unable to unlock the radio, you cannot send or receive any call, nor adjust the volume level with the Rotary Knob. You are asked to enter the PIN code each time you turn on the radio. 31 DRAFT MN001488A01-BF (en-US) Getting Started 2.7.1 Unlocking Your Radio Your radio may be locked at power up. To unlock it after powering on, enter the code at the prompt. Your radio enters the default home display. NOTICE: The unlock code is originally set to 0000. Your service provider may change this number before you receive your radio. 2.7.2 Unblocking Your Radio If you have entered the incorrect PIN code for more than three times (by default), use the Personal Unblocking Key (PUK) to unblock your radio. Procedure:

1 Radio displays Unit Blocked Enter PUK. 2 Enter the eightdigit PUK number. NOTICE: The PUK is an eight-digit master code provided by your service provider. 3 Enter the new PIN code twice. 2.8 Locking or Unlocking the Keys or Buttons Procedure:

2.9 Holding Your Radio Your radio has two microphones: a top microphone for simplex dispatcher/private calls and a bottom microphone for duplex telephone-like calls. The radio is also equipped with an internal speaker for high audio (located at the middle of the unit) and an internal earpiece for low audio (located at the top of the unit). The audio can be routed either to the speaker or the earpiece using the Audio Toggle menu (Menu Setup Audio Audio Toggle) or the assigned One-Touch Button. NOTICE: For best performance speak directly into the top microphone. Simplex Calls When using high audio, hold your radio a vertical position with its top microphone 510 cm away from your mouth. Speak into the top microphone. Listen through the internal speaker. Keep the antenna at least 2.5 cm from your head and body. 32 DRAFT Duplex Calls When using low audio, hold your radio as you would a telephone. Speak into the bottom microphone. Listen through the earpiece. Keep the antenna at least 2.5 cm from your head and body. MN001488A01-BF (en-US) Getting Started Lapel/Shoulder Use For Group and Private Calls turn your head towards your shoulder/lapel, and speak directly into the top microphone. Listen through the internal speaker. Speakerphone Use Place your radio 3060 cm away from you. In a noisy environment, move the radio closer to you for better transmission. 2.10 High or Low Audio Toggle Your radio is able to switch from the external earpiece to the main speaker using One-Touch button and is not required to disconnect the external earpiece or PHF. The states of the routed audio are:

Speaker HIGH indicates that audio is routed to the main speaker. Speaker LOW indicates that audio is routed to the earpiece or PHF earpiece, and not to the main speaker. 2.10.1 Using High Audio When and where to use: Placing or receiving a Phone, PABX, or Duplex Private call. Procedure:

1 Hold your radio in a vertical position with its top microphone 5 cm to 10 cm away from your mouth. 2 Speak into the top microphone and listen through the internal speaker. Keep the antenna at least 2.5 cm from your head and body. 2.10.2 Using Low Audio When and where to use: Placing or receiving a Phone, PABX, or Duplex Private call. Procedure:

1 Hold your radio as you would a telephone. 2 Speak into the bottom microphone and listen through the earpiece. Keep the antenna at least 2.5 cm from your head and body. 33 DRAFT MN001488A01-BF (en-US) Getting Started 2.11 During a Call During the call, label of the right Soft key indicates the next possible change. Accessory default setup is:

Table 8: During the Call Soft Key Label Spkr Erpce PHF Audio Setting Audio goes to the main speaker (Speaker HIGH is displayed) Audio goes to the earpiece (Speaker LOW is displayed) Audio goes to the Personal Hands Free (Speaker LOW is displayed) 2.12 Entering TMO or DMO Mode Procedure:

1 From the home screen, press Options. 2 Select Trunked Mode/Direct Mode. 2.13 Selecting Talkgroups Follow these procedures to select talkgroup manually. If the selected talkgroups is an InterSystem Interface (ISI) talkgroup, your radio can migrate to another talkgroup linked network, changing the talkgroup automatically. Procedure:

From the home screen, use one of the following methods:

Press Left or Right Navigation key. Press Select to confirm. Select Options TG by abc. Enter a talkgroup name and select the talkgroup name from the list. Select Options TG by Folder. Select a folder (for example, Favorite) and then a talkgroup name. NOTICE: Your radio can access up to three levels of the folder structure. Rotate Talkgroup Knob until the required talkgroup name is displayed. 2.13.1 Talkgroup Icons Selection Talkgroup icons are used to indicate that a talkgroup has a special function, show the status of network selection, and/or show the talkgroup properties. A talkgroup without an icon does not have a special function attached to it. 34 DRAFT These icons are displayed next to the talkgroup alias on idle display and when scrolling talkgroups in common or favorite folder lists. MN001488A01-BF (en-US) Getting Started Table 9: Talkgroup Icons Icon TMO Talkgroup Icons Talkgroups in Common Folders In TMO Mode Display when the talkgroup selected is a SIM TMO talkgroup, and not regis-

tered to SIM network. Single network is available. Not displayed in common folders. In TMO Mode Display when the talkgroup selected is an ISI or Any network TMO talkgroup. Multiple networks are available. In TMO Mode Display when TMO ISI talkgroup se-

lected is not assigned to home net-

work. Multiple networks are available. Talkgroups in Favorite Folders In TMO Mode Display when the talkgroup selected is a SIM TMO talkgroup, and not regis-

tered to SIM network. Single network is available. In DMO Mode Display when the talkgroup selected is a SIM TMO talkgroup. Single network is available. In TMO Mode Display when the talkgroup selected is a normal TMO talkgroup. Single network is available. In DMO Mode Display when the talkgroup selected is a normal TMO talkgroup. Single network is available. In TMO Mode Display when the talkgroup selected is an ISI or Any network TMO talkgroup. Multiple networks are available. In DMO Mode Display when the talkgroup selected is an ISI or Any network TMO talkgroup. Multiple networks are available. In TMO Mode Display when TMO ISI talkgroup se-

lected is not assigned to home net-

work. Multiple networks are available. In DMO Mode Display when TMO ISI talkgroup se-

lected is not assigned to home net-

work. Multiple networks are available. In TMO Mode Display when the TMO normal talkgroup selected is not assigned to the current network. Single network is available. 35 DRAFT MN001488A01-BF (en-US) Getting Started Icon DMO Talkgroup Icons Talkgroups in Common Folders Display when a DMO talkgroup is selected. Talkgroups in Favorite Folders General Icons Display when the radio is registered to a network that is not the home network. NOTICE: The icon, also known as Migration icon, is only displayed on the top of the display as a status icon. Display when the radio is locked to a current network selection that is a single network while the current selected ISI talkgroup or Any Net talkgroup allows multiple networks. NOTICE: In common folders, no TMO talkgroups are shown when in DMO mode. 2.14 One-Touch Buttons The One-Touch Button feature allows you to activate a feature by a long key press of the programmable button. Your service provider can also assign one-touch functions to the keypad keys. Description Displays the private dialing editor. Turns Covert Mode on or off. Activates scanning for Bluetooth devices. Selects any network. Selects any talkgroup network. Turns Proximity Pairing on or off. Table 10: One-Touch Button Features Feature Access Private Dialing Ed-

itor Activation of Covert Mode Add Bluetooth Device Any Network Any Talkgroup Network Bluetooth Smart Proximity Pairing Call-Out Box Change Audio Profile Change Talkgroup Displays the list of call-out sessions. Change to the specific audio profile. Changes the talkgroup to the one programmed by your service pro-

vider. Dials a predefined private number. Disconnects all Bluetooth devices connected to the radio. Displays the battery levels of all paired Bluetooth GATT-based sen-

sor devices. Displays the GATT-based sensor data. Direct Private Number Di-

aling Disconnect All Connected Bluetooth Devices Display Bluetooth GATT Sensors Battery Levels Display GATT Service Da-

ta 36 DRAFT MN001488A01-BF (en-US) Getting Started Feature Display Heart Rate Display Operational-Tacti-

cal Address (OPTA) DMO Pre-emptive SDS Flip Display Home Only Home Talkgroup on Home Network Initiate Call-Out Fallback LIP Report Lock to Current Network Message Inbox PABX Call Setup Phone Call Setup Prefer Talkgroup Network Shortcut Private Call Setup Reset to Default RMS MMI Menu RUI Logon or Logoff Scan for Bluetooth Devi-

ces Select Talkgroup Network Shortcut Selecting Audio Profiles Send Double Push PTT Tone (D-PTT) Send Predefined Template

(PDT) Send Status Message Send User-Defined Tem-

plate (UDT) Switch to Previously Se-

lected Talkgroup Timed Talkgroup Change Description Displays the heart rate value received from the connected GATT-

based heart rate sensor. Displays the OPTA. Sends the next DMO SDS or status message with elevated priority. Rotates the display by 180 . Selects only home network. Selects only home network and home talkgroup network. Sends Call-Out Fallback Alert. Sends a message with the location of the radio to a dedicated ad-

dress. Selects the current network only. Displays the list of messages in Inbox. Initiates a PABX call to a predefined entry in the contact list. Initiates a phone call to a predefined entry in the contact list. Displays the Prefer Talkgroup Network menu. Initiates a simplex or duplex private call to a predefined entry in the contact list or to the last group call originator. Resets the radio to its default settings. Opens the RMS menu without activating RMS mode. Asks for the credential or logs off the radio. Activates scanning for Bluetooth devices once OTB assigned to the Add Bluetooth Device function is pressed. Displays the Select Talkgroup Network menu. Scrolls through all available audio profiles. Sends the D-PTT tone to the currently used talkgroup. Sends a predefined message to a dedicated address. Sends a dedicated status message to a dedicated address. Sends a user-defined message to a dedicated address. Changes the talkgroup of the radio to the previously selected talk-

group (DMO or TMO). Makes a predefined talkgroup the selected talkgroup for a specified amount of time. While using the predefined talkgroup, the second press of the One-Touch Button results in:

37 DRAFT MN001488A01-BF (en-US) Getting Started Feature Description the radio returning to the previously selected talkgroup, the radio restarting the predefined time, or no action on the radio, depending on the configuration After the timer expires, the radio returns to the previously selected talkgroup. Toggles the backlight on or off. Regulates the backlight intensity. Turns Discoverable Mode on or off. Toggles Bluetooth GATT Sensor MMI Alerts on or off. Enables or disables BSI encryption. Toggles Call Forwarding on or off. Toggles between TMO and DMO modes. Turns Extra Zoom on or off. Toggles audio high or low. Enables or disables Howling Suppression. Turns Man Down feature on or off. Toggles the RF Power Class between High and Normal. Locks or unlocks the Rotary Switches. Activates or deactivates the RSM earpiece. Activates or deactivates the Screen Saver feature. Turns the Talkgroup Scan feature in TMO Mode on or off. Turns TXI on or off. Activates Bluetooth Indoor Location. Turns Bluetooth on or off. Turns Repeater Mode on or off. The radio displays Unassigned Button when no feature assigned to this button. Displays universal time on the home screen. Press to decrease the volume by one level. Press and hold to contin-

uously decrease the volume to its minimum level. Press to increase the volume by one level. Press and hold to contin-

uously increase the volume to its maximum level. Toggle Backlight Toggle Backlight Intensity Toggle Bluetooth Discov-

erable Mode Toggle Bluetooth GATT Sensor MMI Alerts Toggle BSI Encryption En-

abled or Disabled Toggle Call Forwarding Toggle DMO or TMO Toggle Extra Zoom Toggle Hi or Low Audio Toggle Howling Suppres-

sion Toggle Man Down On or Off Toggle RF Power Class Toggle Rotary Knob Lock Toggle RSM with Earpiece Toggle Screen Saver Toggle Talkgroup Scan Toggle Transmit Inhibit Mode (TXI) Turn Bluetooth Indoor Lo-

cation On or Off Turn Bluetooth On or Off Turn Repeater Mode On or Off Unassigned Universal Time Display Volume Down Volume Up 38 DRAFT MN001488A01-BF (en-US) Modes Modes This chapter contains information on available modes that the radio can operate in. 3.1 Trunked Mode Operation Trunked Mode Operation (TMO) requires the switching and management infrastructure. This operation mode enables various voice and data communication types, such as group calls and short data service messages, as well as access to the infrastructure-related features such as packet data. Figure 3: Trunked Mode Operation 3.1.1 Entering TMO Mode Procedure:

1 Do one of the following:

From the home screen, press Options. From the home screen, press the Menu key. Select Networks. 2 Select Trunked Mode. 3.1.2 Making Group Calls in TMO The Group Call is received by all members of the selected group who have their units turned on and are connected through the network. Procedure:

1 Press and hold the PTT button. 39 DRAFT MN001488A01-BF (en-US) Modes 2 Wait for the Talk Permit tone (if configured) and then speak into the microphone. Release the PTT button to listen. 3.1.3 Receiving Group Calls in Idle Procedure:

1 Your radio receives a Group Call. NOTICE: The incoming Group Call is signaled by a Receiving Group Call tone. 2 To respond, press and hold the PTT button. 3.1.4 Receiving Group Calls during Ongoing Group Calls While in active Group Call, your radio receives a Group Call with a higher priority. One of the following occurs:

Your radio is forced to end the current group call and automatically join the incoming one. Your radio displays incoming group call screen with options:

- Join ends current Group Call and starts the incoming one.

- End cancels the incoming Group Call. 3.1.5 Dynamic Group Number Assignment (DGNA) DGNA allows the network operator to dynamically manage talkgroups on your radio over the air interface. Using DGNA, the network operator can:

Add talkgroups. Attach or select newly added talkgroups. Delete talkgroups. Modify parameters of existing talkgroups. All the above operations are performed by transmitting data to your radio. 3.1.5.1 DGNA Reception When a DGNA message is received, your radio plays a tone and displays a message Talkgroup list updated. If enabled by your service provider, your radio displays all added and deleted talkgroup list. When your service provider deletes (de-assigns) the currently selected talkgroup, depending on the settings, your radio can perform one of the following actions:

Enter the No Group state your radio does not attach to any talkgroup automatically. Attach to the last selected TMO talkgroup. If the last selected TMO talkgroup is not available (it was deleted), your radio enters the No Group state. Attach to a default talkgroup configured by your service provider. If the default talkgroup is not available (it was deleted), your radio enters the No Group state. At each talkgroup change, an appropriate notification is shown on the display. 40 DRAFT MN001488A01-BF (en-US) Modes If the DGNA message is received to delete all talkgroups, your radio displays All Talkgroups Deleted. To exit the DGNA display, you can use the Back Soft key or the End key. 3.1.5.2 DGNA Auto Select Group If the DGNA Auto Select is configured, whenever your radio receives a DGNA, it switches to the added talkgroup. 3.1.5.3 DGNA Auto Reselect Group If the DGNA Auto Reselect is configured, whenever a talkgroup assigned by the network operator through the DGNA is deassigned without the user action, the radio returns to the previously selected group. 3.1.5.4 Viewing DGNA Talkgroups Prerequisites: Your radio receives the DGNA message. Procedure:

1 To view the added talkgroups details press View. 2 Scroll through the list to select required talkgroup. 3 To select the DGNA group, press Attach. 3.1.6 Broadcast Call Broadcast Group Call (also called Site Wide Call) is a high-priority group call from the console operator

(or dispatcher) to all users located at one or more sites. The radios are configured to monitor a Broadcast Call, but you cannot talk back. The call can be received as a normal Broadcast Call or an Emergency Broadcast Call. The Broadcast Call preempts an ongoing Group Call that has the same or lower call priority. 3.1.6.1 Broadcast Calls Initiated by Users This feature allows you to make a Broadcast Call from the radio that is initiated on the predefined talkgroup. Your service provider predefines the alias and the priority of the Broadcast Call. NOTICE: If the type of the encryption is defined by the SIM Card, the Broadcast Call is always clear. Otherwise if the radio uses other encryption service the type of the encryption used for that Call is up to the encryption settings of that service. This feature is not supported on the Dimetra infrastructure. 3.1.6.2 Initializing Broadcast Calls Procedure:

1 From the home screen, press the Menu key. 2 Select Services Broadcast. Your radio displays the predefined alias and the Broadcast Call icon. 41 DRAFT MN001488A01-BF (en-US) Modes 3 To start the call press the PTT button. 3.1.7 Phone and Private Automatic Branch Exchange (PABX) Calls Phone Call allows you to call a landline telephone number or a cellular mobile phone number. Private Automatic Branch Exchange (PABX) Call allows you to call local (office) extension numbers. 3.1.8 Assistance Call This feature allows you make a private call to ask for assistance during normal and non-critical situations. NOTICE: Your service provider can configure the number, priority, and the type of the call

(simplex or duplex). 3.1.9 Call Modification Call Modification is a feature that allows your service provider to modify the call to optimize it and adjust to a current situation. Modification can cover:

Call priority Modified during call setup. Call type Modified during call setup. Call encryption Modified during an ongoing call, but not in the transmission phase. When the call is modified, your radio displays Call Modified message. When a recently modified call requires the PTT button to transmit, your radio displays Call Modified Use PTT. All modifications are made by your service provider and the radio only follows them. You have no influence on ongoing call modifications. When call priority is changed to emergency:

The display indicates that an Emergency Group Call has been received. The radio plays a special audio alert. NOTICE: If a Group Call is modified into an Emergency Group Call, no emergency-related features are triggered. If the radio cannot follow a call modification requested by the service provider, due to its settings, the radio rejects it and displays Service Not Available message. 3.2 Local Site Trunking This mode is also called as Fallback Mode and it allows more than one radio from the same site to communicate when the link between the site and the network central controller fails. Entering and exiting Local Site Trunking (that is, returning to System Wide Services) is done automatically. In this mode, some services are unavailable. 42 DRAFT MN001488A01-BF (en-US) Modes NOTICE: Your service provider can disable this mode. 3.2.1 Entering Local Site Trunking When your radio receives a Local Site Trunking indication from the system, the following occurs:

Your radio plays an Entering Local Site Trunking tone. Display shows the Local Area Service message. Display icons and soft keys turn olive. NOTICE: Noticeable only on the color display. Any call in progress is dropped upon entering Local Site Trunking Mode. If configured by your service provider, this message/alert is periodically repeated to remind you that your radio is still operating in Local Site Trunking Mode. The following features are available:

Registration Attachment Group Call Emergency Call Emergency Alarm 3.2.2 Exiting Local Site Trunking When the link with the central network controller is reestablished, your radio exits Local Site Trunking, and the following occurs:

Your radio plays an Exiting Local Site Trunking tone. Any call in progress during Local Site Trunking is dropped. Display icons and soft keys turn blue. 43 DRAFT MN001488A01-BF (en-US) Modes 3.3 Direct Mode Operation Direct Mode Operation (DMO) is a mode of simplex operation where radios communicate directly without the need of a network. Figure 4: Direct Mode Operation 3.3.1 Entering DMO Mode Procedure:

To enter the DMO Mode:

From the home screen, press the Menu key. Select Networks Direct Mode. From the home screen, press the Menu key. Select Options Direct Mode. 3.3.2 Making Group Calls in DMO The Group Call is received by all members of the selected group who have their units turned on and are in range. Procedure:

1 Press and hold the PTT button. 2 Wait for the Talk Permit tone (if configured) and then speak into the microphone. Release the PTT button to listen. 3.3.3 Receiving Group Calls in Idle Procedure:

1 Your radio receives a Group Call. NOTICE: The incoming Group Call is signaled by a Receiving Group Call tone. 2 To respond, press and hold the PTT button. 44 DRAFT MN001488A01-BF (en-US) Modes 3.3.4 Selecting DMO Communications Options When and where to use: Helps to communicate with other radio users on the same talkgroup through the Gateway or Repeater. Procedure:

1 From the home screen, press Options. 2 Press Config. 3 Select one of the following:

MS - MS Your radio can communicate only with other radios within its range. Gateway Your radio uses a gateway to communicate with the infrastructure. Automatic Your radio uses the first available gateway for that talkgroup. Specific Your radio uses only the Gateway with the specified Gateway address for that talkgroup. If your radio displays Selected Gateway: None, press Edit to enter the current gateway address. Repeater Uses the first available repeater for that talkgroup. GW + Rep Uses the first available gateway or repeater for that talkgroup. Automatic Uses the first available gateway for that talkgroup. Specific Uses only the Gateway with the specified Gateway address for that talkgroup. If your radio displays Selected Gateway: None, press Edit to enter the current Gateway address. NOTICE:

When the Gateway and the Repeater cannot be communicated even though a talkgroup to use them is configured, the radio attempts the direct MS-MS communication. When your radio detects the appropriate Gateway and/or the Repeater, the Gateway and/or Repeater icons turns solid, respectively. 3.3.5 DMO Private Priority Call The service provider may assign Pre-emptive Priority to outgoing DMO Private Calls. If this is the case, DMO Private Calls from this radio preempt any ongoing calls (with the exception of emergency calls or ongoing Pre-emptive Priority Private Calls) on the receiving radio, which then displays Call-

preempted. 3.3.6 Talkgroup for Individual Calls Talkgroup for Individual Calls is a talkgroup that operates on a separate frequency allocated for individual (private) calls only. Using this talkgroup optimizes frequency resources and helps not to block other talkgroups. The only supported call types are: private calls and emergency calls (both private and group). Use this talkgroup each time you need to make a private call. When you select a Talkgroup for Individual Calls, your radio is not able to receive or initiate any group or broadcast calls with priority lower than Emergency. When you have selected a Talkgroup for Individual Calls and press the PTT button to start a Group Call, the radio:

45 DRAFT MN001488A01-BF (en-US) Modes Rejects the call Plays a tone Displays the Individual Calls Only message 3.3.7 Network Monitor This feature allows the radio to monitor for TMO individual calls while maintaining DMO services. When Network Monitor is active, the radio receives direct calls addressed to the selected DMO talkgroup, private DMO calls, SDS messages, but also private TMO calls. The group calls, private calls, and SDS messages initiated are configured in DMO. Only responses to private TMO calls are sent in TMO. 3.3.7.1 Enabling Network Monitor Prerequisites: Ensure your service provider enabled the Network Monitor feature. Procedure:

1 From the home screen, press Options. 2 Press Network Monitor. 46 DMOTMOPrivate CallDRAFT MN001488A01-BF (en-US) Modes 3.3.8 Communication through Repeaters Radios that are out of range and cannot communicate directly with each other in Direct Mode Operation (DMO) can do it through the repeater. The repeater is a radio that repeats all communication on a chosen channel, and as a result increases radios DMO range. Figure 5: Communication through Repeaters When the radio connects to a repeater, it plays a tone, displays the Repeater available message, and shows an appropriate icon. When the radio loses connection with the repeater, it plays a tone, displays the Repeater not available message, and the repeater icon is blinking. 3.3.9 Communication through Gateways Gateway provides connectivity between radios operating in Direct Mode Operation (DMO) and the TETRA network, so that the DMO radios can communicate with the Trunked Mode Operation (TMO) radios. Figure 6: Communication through Gateways 47 DMODMODMOTMOTMODRAFT MN001488A01-BF (en-US) Modes When the radio connects to a gateway, it plays a tone, displays the Gateway available message, and shows an appropriate icon. When the radio loses connection with the gateway, it plays a tone, displays the Gateway not available message, and the gateway icon is blinking. 3.3.10 Gateway and Repeater Synchronization To communicate using gateways or repeaters, the radio requires synchronization with a gateway or a repeater. A gateway or a repeater sends presence signals to radios. If a radio receives presence signals, it stays synchronized with the gateway or the repeater which sends the signals. If a radio fails to receive a presence signal it does not immediately lose synchronization. The radio waits for another successful presence for a time defined by your service provider. This function ensures that communications are not dropped due to temporary reception issues. If a gateway or a repeater is unavailable or the radio is not synchronized with a gateway or a repeater, depending on the setup configured by your service provider, the following scenarios apply:

The radio falls back to Direct Mode Operation (DMO). After pressing the PTT button, a prompt appears warning that the second press overrides the gateway or repeater operation mode. No direct DMO communications are permitted. In the second scenario, while the radio receives individual calls and group calls, and replying to individual calls is possible, replying to group calls is not possible. 3.4 Transmit Inhibit Mode The Transmit Inhibit (TXI) Mode is a mode in which the radio sends no radio transmissions. Activate this mode in RF sensitive areas, for example hospitals, airplanes, where safety can be jeopardized due to transmission radiation. To activate, select Menu Networks TXI Mode Activate. In this mode, the radio does not transmit under any circumstances except for the Emergency Calls. All the functions and keys which cause transmission, for example registration to the network, changing talkgroup or folder, sending SDS messages, or pressing the PTT button are disabled. Any transmission trial causes the radio to display Not Allowed In TXI Mode notification and to play a tone. Your radio can still receive:

Group calls Messages - stored in the Inbox Private call attempts - stored in the Missed Calls list, without the option to respond When no danger to safety exists anymore, for example, when you leave the RF sensitive area, you can deactivate the TXI Mode and the radio returns to standard operation. You can deactivate the mode by selecting Menu Networks TXI Mode Deactivate, pressing One-Touch Button, or implicitly when initiating an Emergency Call. NOTICE: RF Transmissions from the radio are prevented under the following conditions:

TXI Mode is activated. Battery is removed. The radio is turned off. 48 DRAFT MN001488A01-BF (en-US) Modes On entering or exiting the TXI mode, when the radio is camped on a cell, it sends a specially designated Short Data Service (SDS) status message. This SDS message indicates to the SwMI that the radio is entering or exiting TXI mode. Mobility procedures that do not require the radio to send an uplink transmission are performed except for cell reselection. In TXI mode, the radio joins group calls for any group that the radio is monitoring, but the transmitting on that call is still prohibited. The radio also displays any incoming SDS messages to the user. The missed call feature is active in the TXI mode and allows checking what calls were missed. However, the radio attempts to prevent call setup retransmission from being recorded as separate calls. If you initiate an emergency call, the radio immediately leaves TXI mode and attempts to start the emergency call if the radio is in service. If the radio is turned off in the TXI mode, on turning on, the radio asks whether to exit the TXI mode. If you choose No, the radio turns off. 3.5 Emergency Operations Emergency Operations are used in critical situations. Pressing and holding the Emergency button, or entering the Emergency Number and pressing the Send key, activates one or more services (depending on your service provider settings):

Emergency Alarm SDS Status Silent Emergency Hot Microphone operation Emergency Individual Call (Private or MS-ISDN) NOTICE: It is possible to turn on the radio by pressing the Emergency button. Depending on the service provider settings, the radio can start Emergency Operations automatically. If the radio is PIN-protected (except for SIM PIN), Emergency Operations bypass the PIN lock. When starting Emergency Operations, any ongoing voice call is aborted or cleared down, and any packet data transfer in progress is aborted. However, the session is kept open. During Emergency Operations, the radio rejects phone, PABX, and private calls, and does not monitor the talkgroups in the selected scan list. To terminate Emergency Operations, press the Right soft key. 3.5.1 Emergency Alarm The Emergency Alarm is a special status message sent while starting the Emergency Operations. The radio sends the message in either TMO or DMO. Each time the radio enters the Emergency Operation, it sends the Emergency Alarm. When the Emergency Alarm is sent successfully, the respective audible tone sounds. In addition, pressing the Emergency button when the radio is in the Emergency Operation resends emergency alarm (exception: during Hot Microphone transmission). 49 DRAFT MN001488A01-BF (en-US) Modes 3.5.2 Emergency Group Call The Emergency Group Call has the highest communication priority and it is a pre-emptive call. Emergency Group Call is available in both TMO and DMO. During Emergency Operations, start Emergency Group Call by pressing the Emergency button. The radio can also support Hot Microphone operation, which allows the Emergency Call to be conducted without pressing the PTT button. When a radio receives or generates a group call with emergency priority, the display changes color to red and a red triangle icon is displayed. A special alert tone is played. An emergency group call can be configured as:

A non-tactical call initiated on a talkgroup preprogrammed by your service provider. When in non-

tactical emergency mode, you cannot switch talkgroups. A tactical call initiated on the currently selected talkgroup. Pressing the Emergency button during an ongoing emergency broadcast call has no effect. No new call is started and no emergency alert is sent. When the Emergency Group Call you participate in terminates, your radio can behave in several ways, depending on your service provider settings:

If you are the call initiator, the radio can either stay in the Emergency Mode, or return to TMO. If you are not the call initiator, the radio always returns to TMO. 3.5.2.1 Making Emergency Group Calls Prerequisites: Ensure that your radio is in Emergency Mode. Procedure:

1 Press and hold the PTT button. 2 Wait for the talk permit tone (if configured) and talk. 3 Release the PTT button to listen. NOTICE: It is possible to cancel making an emergency group call in TMO. To do this, perform one of the following actions before the talk permit is granted (depending on your service provider settings):

Release the PTT button. Press the End key (default). When the call is canceled, your radio displays Call Cancelled message (if configured by your service provider). 3.5.2.2 Receiving Emergency Group Calls The radio receives an Emergency Group Call from a selected pre-programmed group. An appropriate tone, status icon, and red color of the display indicates an incoming call. 50 DRAFT MN001488A01-BF (en-US) Modes 3.5.3 Non-Tactical Emergency In Non-Tactical Emergency, the radio switches to a designated Emergency talkgroup when starting Emergency Operations. This talkgroup is used for the complete duration of the Emergency Operations and changing talkgroup is not allowed. In Trunked Mode Operation (TMO), it is possible to configure the radio to make Emergency Non-

Tactical Group Calls without sending attachment. If set, the radio assumes implicit attachment after receiving a temporary address. In Direct Mode Operation (DMO), the Non-Tactical Emergency proceeds on the same frequency as the previously selected talkgroup. The service provider can designate any Individual TETRA Subscriber Identity (ITSI) address to be used for Emergency Operations and this ITSI can be an Open Group -

broadcast address. After exiting from Non-Tactical Emergency, the radio goes back to the previously selected talkgroup. 3.5.4 Emergency Individual Calls (Private or MSISDN) The Emergency Individual Calls are Simplex or Duplex Calls with emergency priority. On pressing the Emergency button, the radio initiates an Individual Call to the provisioned address (private or MSISDN). During this kind of call, all user indications are unavailable and all other services are rejected. Emergency Operation ends when the Emergency Individual Call is ended. 3.5.5 Emergency SDS Status The radio sends a status message with a preprogrammed value to the destination address set by your service provider. Emergency SDS Status is available in TMO only. If no status acknowledgment or negative acknowledgment is received, the radio retries sending the message. Status is not resent when Emergency Alarm or Hot Microphone is configured. 3.5.6 Emergency Hot Microphone The Hot Microphone allows you to talk without pressing the PTT button during Emergency Operation. The transmission continues for a provisioned amount of time. Pressing the PTT button before the Hot Microphone time expires ends the Hot Microphone operation. Then normal PTT operation in Emergency group call takes over whereby the transmission is ongoing for the time the PTT button is held. Subsequent Emergency button presses during the Emergency Operation restart the Hot Microphone transmission. If a talk permit is granted to another member of the group, the Emergency Call received tone is played. If configured, the radio automatically attempts to get talk permit again. Pressing End soft key or End key ends the Hot Microphone operation. 3.5.7 Alternating Hot Microphone The Alternating Hot Microphone is an enhancement of the Hot Microphone. After activation, the radio alternately enters transmission phases (your microphone is active) and reception phases (you can only listen) for an amount of time precisely determined by your service provider. 51 DRAFT MN001488A01-BF (en-US) Modes If this feature is enabled, you can initiate the Alternating Hot Microphone by pressing the Emergency button. If you want to finish earlier or skip the transmission phase, press the End key. The Alternating Hot Microphone terminates when one of the following conditions is met:

The radio exits the Emergency Mode. The Alternating Hot Microphone timer expires. The PTT button is pressed. The Right soft key is pressed (only during the transmission phase). NOTICE: When the radio goes out of the service, it enters the reception phase and the Alternating Hot Microphone is on hold. When the radio is back to the service, the Hot Microphone transmission and the Alternating Hot Microphone resume. When you are in the Emergency Mode, pressing the Emergency button restarts the Alternating Hot Microphone. 3.5.8 Silent Emergency Mode The Silent Emergency Mode is a type of emergency services that provides no audible indications nor keypad tones at the entrance. All the display indications are as in the home mode. However, the radio cannot use any services except for:

Receiving Ambience Listening Sending Silent Emergency Alarms Sending GNSS location reports NOTICE: The radio blocks any other feature that you try to activate. If the Silent Emergency feature is enabled, the radio enters Silent Emergency Mode on pressing the Emergency button. After entering this Mode the radio stays in TMO or switches to it, depending on the actual state. Once in TMO, the radio sends Silent Emergency Alarm. NOTICE: If the radio is in a private or group call, the radio waits until the call ends and then enters the Silent Emergency Mode. The radio keeps re-sending the alarm until successful sending is confirmed. After the alarm is successfully delivered, the radio stays in Silent Emergency Mode and waits for the Ambience Listening. Your radio exits the Silent Emergency Mode, under the following conditions:

No success in sending the Silent Emergency Alarm and the maximum number of retries has been reached. The control room terminates the Silent Ambience Listening. The Ambience Listening is disconnected due to another reason. If you turn off the radio in the Silent Emergency Mode, the radio switches to pseudo power off state. In this state, the radio appears to be turned off. However, the radio is still on and in the Silent Emergency Mode. On turning the radio on during the pseudo power off state, the radio acts as during turning on and still is in the Silent Emergency Mode. 3.5.9 Invisible Emergency It is possible for the service provider to disable visual and audible indications when performing Emergency Operation on the radio, known as Invisible Emergency. Invisible Emergency provides an 52 DRAFT MN001488A01-BF (en-US) Modes extra layer of safety when using Emergency Operation in a critical situation, for example during a direct attack on the user. 3.5.10 Emergency Alert This feature allows the radio to send emergency alerts to other radios within its DMO coverage by pressing the Emergency button. Even in TMO mode, the radio monitors a special DMO emergency frequency for possible emergency alerts, and responds to them by automatically joining the emergency call. To initiate the emergency alert, the radio must be in MS-MS DMO mode or out of coverage in TMO mode. The alert is not sent to the dispatch console. To receive the emergency alert, the radio must be in DMO or TMO, within RF range of the initiating radio, and must not be in a call. When the radio receives the emergency alert, it joins the call automatically. The following table illustrates the dependencies between the current radio mode and the type of emergency operation:

Table 11: Emergency Operation Dependencies Radio Mode Initiate Emergency DMO, MS-MS, idle DMO, Repeater, idle DMO, Gateway, idle DMO, in call TMO, no coverage TMO, in coverage, idle TMO, in coverage, in call Network Monitor, MS-MS Network Monitor, Repeater Gateway operation, in cover-

age Repeater operation Emergency Alert Standard DMO Emergency Standard DMO Emergency Per communication mode Emergency Alert Standard TMO Emergency Standard TMO Emergency Emergency Alert Standard DMO Emergency Standard TMO Emergency Standard DMO Emergency Emergency Alert Received

(Yes/No) Yes Yes Yes No Yes Yes No No No No No 3.5.11 Disaster Alert Disaster Alert call is a broadcast emergency call initiated by the radio, with emergency pre-emptive priority that everyone in a broadcast area can hear. This feature is designed for catastrophic situations, such as earthquakes, and has the highest priority over other calls. All radios under Disaster Alert display emergency notification on their screens. The alert message, its duration, and destination talkgroup can be configured in the codeplug. To initiate Disaster Alert, switch the radio to Disaster Alert mode and press PTT button. When the call ends, the radio exits the Disaster Alert state. During Disaster Alert, other functionality is impacted:

When Disaster Alert begins, any other ongoing services are terminated. 53 DRAFT MN001488A01-BF (en-US) Modes No other services can interrupt this type of call. Hot Mic functionality cannot be used. Speech can only be in Clear mode, even if any of the encryption services are enabled. The only exception is E2E Encryption. NOTICE: Not all infrastructures support this feature. Consult service provider before enabling this feature. 3.5.11.1 Initializing Disaster Alert Calls Procedure:

1 From the home screen, press the Menu key. 2 Select Services Disaster Alert. Your radio enters Disaster Alert Mode and it displays Disaster Alert icon. 3 To start the call press PTT. Your radio displays Disaster Alert In Use. 3.5.12 Exiting Emergency Operations Prerequisites: Make sure that your radio is engaged in Emergency Operations. Procedure:

1 If your radio screen displays Emergency Mic On, press End. 2 Press and hold Exit. Your radio exits Emergency Operations. 3.6 Repeater Mode NOTICE: This feature is a paid feature. The Repeater Mode provides repeater connectivity between radios operating in the DMO Mode. 54 DRAFT Figure 7: Repeater Mode Operation MN001488A01-BF (en-US) Modes A DMO repeater is used to extend the DMO range by retransmitting received information from one radio to another. It retransmits group calls, private calls and data on a given frequency. In the diagram above the radio in the middle is a repeater. The repeater sends presence signal periodically on a free channel to allow other radios to synchronize on a given frequency. Only the radios on the same talkgroup can communicate with each other through the repeater. The Repeater Mode is activated by selecting Menu Networks Repeater Mode. 55 DMODMODRAFT MN001488A01-BF (en-US) Main Menu Main Menu This chapter contains information on items in the main menu. You can enter the menu items during a call. If not programmed otherwise by your service provider the radio exits the menu, when a new call starts. IMPORTANT: Some menu items are model-specific and may not be activated or available on your radio. 4.1 Scrolling through the Menu Procedure:

1 From the home screen, press the Menu key. 2 Scroll to the required item by pressing Navigation keys. Press the Soft key assigned as Select or Right Navigation key to select. If the menu item contains a further set of menu items, repeat step 2. 4.2 Menu Icons The following icons make it easy to identify the menu items at first glance. Table 12: Menu Icons Menu Icon Description Main Menu Items/Context Sensitive Menu It is assigned to Menu when the main menu items / context-sensitive menu are active. Messages Send status messages. Send text messages (free text or according to user defined or predefined templates). Received messages in Inbox. Contacts Add, search, edit, or erase entries in the contact list. Bluetooth Allows you to manage Bluetooth settings. Browser Starts the WAP browser. Security Lets you turn on/off and verify security features, and change passwords. 56 DRAFT Menu Icon Description Setup Allows you to customize your radio. MN001488A01-BF (en-US) Main Menu Group Setup Contains additional menu items for Scanning Talkgroups features. My Info Displays information about your radio and its numbers. Recent Calls Contains a list of recent calls. RUI Allows you to log in and log out of the radio. Networks Allows you to select a network. Location Displays location of your radio. Packet Data Allows you to send data from your radio to other devices. Crypto Menu Allows you to manage SIM Card End-to-End Encryption. Services Allows you to manage Broadcast, Assistance, and Disaster Calls. Indoor Location Allows you to enable or disable Indoor Location. 4.3 Messages This feature allows you to send and receive text messages. A message can contain up to 1000 characters, depending on your service provider settings. Pressing the PTT button when a message is highlighted can cause one of the following actions, depending on your service provider settings:

The radio ignores the PTT button request. The radio starts a Private Call with the message sender. The radio starts a Group Call on a currently selected talkgroup. See Writing Text on page 129 for details on writing a text message. 4.3.1 New Message This menu item allows you to create a new message. NOTICE: While editing a text, Status Icons change their appearance and only four of them are displayed: Tower, Signal Strength, Emergency, and Battery. 57 DRAFT MN001488A01-BF (en-US) Main Menu 4.3.1.1 Sending Messages to Private/Phone Procedure:

1 From the home screen, press the Menu key. 2 Select Messages New Message. 3 Enter your message and press Send. 4 If needed, select Private/Phone. 5 Enter recipient number or press abc to choose it from your contacts. NOTICE:

For Private target selection, you can enter either Individual Short Subscriber Identity

(ISSI), Individual TETRA Subscriber Identity (ITSI), or Group Short Subscriber Identity

(GSSI) of the recipient. ISSI/ITSI a unique, individual ID assigned for each radio. GSSI in Dimetra called Group ID or Talkgroup ID. 6 Press Send, or Send key, or the PTT button. 4.3.1.2 Sending Messages to Groups Procedure:

1 From the home screen, press the Menu key. 2 Select Messages New Message. 3 Type your message and press Send. 4 If needed, select Group. 5 Select a group to send the message. 4.3.1.3 Sending Store and Forward Messages Prerequisites: Your service provider enables the Store and Forward feature. Procedure:

1 From the home screen, press the Menu key. 2 Select Messages New Message. 3 Press Menu key and select Message Setup On/Offline users. 4 Enter your message and press Send. 5 If asked for the Target selection, select one of the following:

58 The text.|SendDeleteDRAFT MN001488A01-BF (en-US) Main Menu Private enter the private number or press abc to choose the destination number from the contact list. Phone enter the phone number or press abc to choose the destination number from the contact list. NOTICE: Your service provider can enable to send a Store and Forward message to a talkgroup. 6 Select Send, or press Send key or PTT button. 4.3.1.4 Delivery Report Delivery Report is an acknowledgment that the radio can request upon sending a message to an individual recipient. You can define what type of Delivery Report your radio requests, or turn on/off this feature. If the Delivery Report is received shortly after the message was sent, the radio:

Displays a pop-up with one of the following messages:

- Message Sent if no Delivery Report is requested (and when a Store and Forward message has been received at the Store and Forward server).

- Message Delivered if the Delivery Report is requested and the message has been received by the target radio.

- Message Read if the Consumed Delivery Report is requested and the message is opened on the target radio.

- Message Failed if the Delivery Report is requested and the message has not been received by the target radio within a defined time period. Saves the Delivery Report in Outbox along with a copy of the message. If the Delivery Report is received after a longer period of time, the radio:

Saves the Delivery Report in Outbox along with a copy of the message. If Delivery Report Notifications functionality is configured by your service provider, the radio also:

- Temporarily saves a Delivery Report message in Inbox. The notification disappears after it is read.

- Displays New Message icon.

- Displays New Delivery Status notification screen (if possible). 4.3.1.4.1 Viewing Delivery Reports Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Inbox. 3 Find a required message and select Read. 4 Press Menu key. 5 Select Delivery Status. 59 DRAFT MN001488A01-BF (en-US) Main Menu 4.3.1.4.2 Configuring Delivery Reports Prerequisites: Your service provider enabled the delivery report configuration. Procedure:

1 From the home screen, press the Menu key. 2 Select Messages New Message. 3 Press Menu key and select Delivery Report. 4 Select one of the following:

None the radio does not request any delivery report. Received the radio requests reports on your messages that were received. Consumed the radio requests reports on your messages that were read. Both the radio requests reports on your messages that were received and read. 4.3.2 Inbox The Inbox folder contains up to 100 new or old incoming messages, depending on the length of the messages. Table 13: Inbox Icons Icon Description Unread (New) Message Read (Old) Message Unread (New) Protected Message Read (Old) Protected Message Message Protected Sender Information in Message View name or number Time and Date Stamp in Message View arrival time and date Delivery Status Received delivery status for Store and Forward messages Messages sub-menu indicates the number of the messages. If the indication is for example 2/4, it means that two unread and four read messages are in the Inbox. 60 DRAFT MN001488A01-BF (en-US) Main Menu 4.3.2.1 Entering the Inbox Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Inbox. NOTICE: The status (if any) of the list is displayed for a few seconds:

No New or Old Messages The screen returns to the previous display within a few seconds. Inbox Full Select OK. 4.3.2.2 Receiving New Messages Prerequisites: Your radio displays a New Message icon, an animation, and plays a New Mail Received tone. Procedure:

Select one of the following:

Read opens the entire message. Back dismisses the message. You can access the message later from the Inbox. 4.3.2.3 Using Submenus in the Inbox and the Outbox Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Inbox or Outbox. 3 Highlight the required message and press Menu key. 4 Do one of the following:

Store Saves a message as a template. Change the default template name and press OK. Delete Deletes the selected message. Press Yes to confirm. Delete All Deletes all the messages in the Inbox or Outbox. Press Yes to confirm. Reply (only for Inbox) Invokes the edit screen with the old message as default text and the message originator as a recipient. After editing, press Send, the PTT button, or the Send key to send. Resend (only for Outbox) Invokes the edit screen with previously entered text with the same recipient. After editing, press Send, the PTT button, or the Send key to send. Forward Invokes the edit screen with the old message to send it to a different participant. After editing, press Send, the PTT button, or Send key to send. Refresh Re-orders the message list and displays the new messages. Delivery Status (only for Outbox) Shows the date and time of the message when it is sent, delivered, read, and expired; was not delivered, expired was not read, or failed unknown. Protect Protects the message from being deleted or overwritten. Unprotect Remove the protection of the message. 61 DRAFT MN001488A01-BF (en-US) Main Menu Message protection functionality is enabled in the Inbox and Call Out Inbox. Users can only delete unprotected messages. 4.3.2.4 Embedded Number This feature allows you to call a number from a message or to start a group call with the message sender talkgroup. 4.3.2.5 Storing Numbers from Messages Prerequisites: Embedded Number feature is enabled by your service provider. When and where to use: You can save the number of the sender or embedded number from the message to a new or existing contact. Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Inbox. 3 Highlight the required message and select Read. 4 Press the PTT button. 5 Radio displays a list of the numbers (including the senders number). 6 Highlight the required number and press Store. 7 Highlight required contact and press View. NOTICE: To store a number for a new contact, select [New Contact] and fill out the required fields. Press Done to save it. 8 Select Edit. 9 Choose the Type of the new number and press Done. 4.3.2.6 Calling Numbers in Messages Prerequisites: Embedded Number feature is enabled by your service provider. When and where to use: You can return a voice call to the sender of a message or to any number that is embedded in the message text. Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Inbox. 3 Highlight the required message and select Read. 4 Press the PTT button. 5 Radio displays a list of the numbers (including the senders number). 6 To call, highlight to the required number and press the PTT button or the Send key. 7 Select Ctype to choose the type of call (Private, Phone, or PABX). 8 Press the PTT button or the Send key. 62 DRAFT MN001488A01-BF (en-US) Main Menu 4.3.2.7 Making Group Calls on the Talkgroup of the Message Sender Prerequisites: Embedded Number feature is enabled by your service provider. Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Inbox. 3 Highlight the required message and press the PTT button. 4.3.2.8 Immediate Message NOTICE: This feature is a paid feature. When the new immediate message is received, radio plays the New Mail Received tone and displays the content overlapping your previous screen. All immediate messages are stored in the Inbox. If the radio is in PIN Lock state, immediate message is displayed after correct PIN is entered. The message stays on the screen until you press the End/Home key. 4.3.3 Outbox Outbox stores up to 100 sent messages arranged chronologically with the last sent message at the top of the list. Table 14: Outbox Icons Icon Description Delivery in Progress Delivery Accomplished Delivery Failed Successful Outgoing Message Failed Outgoing Message Protected Message Delivery in Progress Protected Message Delivery Accomplished Protected Message Delivery Failed Successful Outgoing Protected Message Failed Outgoing Protected Message 63 DRAFT MN001488A01-BF (en-US) Main Menu 4.3.4 Call-Out (CO) Box CO Box contains incoming and outgoing Call-Out messages. Clicking Select on a Call-Out message headline displays more detailed information on the item. When the radio is in normal mode, you are able to browse through all messages in the CO Box. However, if the radio is in the Call-Out mode, you can only browse through the information regarding the currently ongoing Call-Out message. 4.3.4.1 Call-Out Icons Table 15: Call-Out Icons Icon Description Read (Old) Call-Out Message in Inbox Unread (New) Call-Out Message in Inbox Read (Old) Protected Call-Out Message in Inbox Unread (New) Protected Call-Out Message in Inbox Read (Old) Call-Out Message in Outbox Read (Old) Protected Call-Out Message in Outbox 4.3.5 Wireless Application Protocol (WAP) Box Each WAP Push message can be loaded immediately or stored as a message in WAP Box. To access the WAP Box, press Menu Messages WAP Box. All the WAP Push messages are passed to the browser. 4.3.6 Templates Templates box stores user-defined message templates. Each of the Inbox and Outbox message can be stored as a template. Each template name and text can be edited afterwards. 4.3.6.1 Sending User-Defined Templates Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Templates. 3 Highlight the required template name and press Send. 4 Do one of the following:

64 DRAFT Enter the number or press abc to select the name from your contact list. Press Send. Select required talkgroup from the TalkGroup List. MN001488A01-BF (en-US) Main Menu 4.3.6.2 Managing User-Defined Templates Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Templates. 3 Highlight the required template and press Menu. 4 Select one of the following:

View Displays template text. Delete Deletes the template. Edit Text Opens edit screen with the template text. Edit the text and press Menu. Select Save Changes to save edited template, or Store to save the edited template as a new one. Edit Name Opens edit screen with the template name. Press Ok to save the template. 4.3.7 Predefined Templates Predefined message templates are programmed into your radio. You are allowed to perform limited edit operations of the predefined template. You can send it, but you are not able to store the edited template or erase it from the predefined template list. 4.3.7.1 Viewing Predefined Templates Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Predefined. 3 Highlight the required template and press Menu key. 4 Select View. 4.3.7.2 Sending Predefined Templates Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Predefined. 3 Highlight the required template and press Send, the PTT button, or the Send key. NOTICE: You can edit the predefined template before you send it. Press the Menu key and select Edit. Edit screen opens with the template text. You are only allowed to replace the existing text. 65 DRAFT MN001488A01-BF (en-US) Main Menu 4.3.8 Status Messages The radio allows you to send two types of status messages: statuses and targeted statuses. Your service provider determines which type is enabled on the radio. Statuses can be sent either to a selected talkgroup or to a private number programmed by your service provider. Targeted statuses can be sent to any talkgroup defined for the radio or to any private number

(from the contact list or entered manually). 4.3.8.1 Viewing a Status Message Number Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Send Status. 3 Press the Menu key and select View. 4.3.8.2 Sending Status Messages This procedure allows you to send status messages to either a selected talkgroup or a programmed private number. Only one option can be enabled at a time. Prerequisites:

If sending statuses to talkgroups is enabled: switch to the talkgroup to which you want to send a status message. If sending statuses to private numbers is enabled: no action is needed, the private number is set up by your service provider Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Send Status. 3 Highlight the required status message and press Select, the PTT button, or the Send key. 4.3.8.3 Targeted Status Messages This feature enables sending status messages to user selectable addresses. By default, targeted status messages can be sent to private or talkgroup addresses. Your service provider may restrict valid addresses to numbers stored in Contacts. NOTICE: This feature is not supported on Dimetra networks. 4.3.8.3.1 Sending Targeted Status Messages Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Send Status. 3 Highlight the required status message and press Select, the PTT button, or the Send key. 66 DRAFT MN001488A01-BF (en-US) Main Menu 4 Do one of the following:

Enter the number or press abc to select the name from your contact list. Press Send. Select required talkgroup from the TalkGroup List. The display shows one of the following delivery reports:

Status Sent. Status Failed. 4.3.9 Sending an RMS Status Prerequisites: This feature is only available when enabled by your service provider. See Radio Messaging System (RMS) on page 126 for details. Procedure:

1 Do one of the following:

From the home screen, press Menu Messages Send RMS/FMS. Press and hold the One Touch Button configured to display the Send RMS/FMS menu. NOTICE: The navigation through the radio menu is only available if your service provider enabled the Send RMS/FMS menu item. However, your service provider can configure a One Touch Button to display the Send RMS/FMS menu even if the navigation is not possible. If the Send RMS/FMS menu item is disabled, and no One Touch Button is configured to display the Send RMS/FMS menu, then the radio can only receive RMS messages but cannot send them. 2 Scroll to the required RMS status. 4.3.10 Additional Address The Additional Address feature allows the radio to send RMS messages, and Local Information Protocol (LIP) reports to additionally defined recipients. The default addresses where the radio sends RMS messages and LIP reports are defined by your service provider. If an Additional Address is selected and enabled, RMS messages and LIP reports are also sent to the recipient defined in the Additional Address. You can create, edit, and delete Additional Addresses using the radio menu. If an Additional Address is configured by your service provider, the service provider can disable edition and deletion of the address using the radio menu. You can define up to 30 Additional Addresses. 4.3.10.1 Enabling or Disabling Additional Address Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Additional Address Enable. 3 Select one of the following:

On to activate the feature 67 DRAFT MN001488A01-BF (en-US) Main Menu Off to deactivate the feature 4.3.10.2 Selecting Additional Address Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Additional Address Select Address. Select Address display appears with an available list of aliases. 3 Scroll through the list to highlight your alias and press Select. 4.3.10.3 Viewing Additional Address Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Additional Address Select Address. 3 Scroll to select the alias of the Additional Address you wish view. 4 Press the Menu key. 5 Select one of the following:

Edit (for User Defined Additional Address alias) View (for Pre-defined Additional Address alias) The display shows the Alias, the ISSI/ITSI/GSSI and the Status of the address (Pre-Defined or User Definded). 4.3.10.4 Entering New Additional Address Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Additional Address Select Address. 3 Select [New Address]

4 Press Change key. 5 Enter new values of the Alias and ISSI/ITSI/GSSI fields, press Done key. The new alias appears in the list of available aliases. There is no possibility to have two Additional Address items with the same Additional Address Alias. 4.3.10.5 Editing Additional Address Prerequisites: Editing Additional Address is allowed only for User-Defined positions. Pre-Defined positions can only be Selected or Viewed. Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Additional Address Select Address. 68 DRAFT MN001488A01-BF (en-US) Main Menu 3 Highlight the alias. 4 Press Menu key. 5 Select Edit. 6 Press Change. 7 Enter new values of the Alias and ISSI/ITSI/GSSI fields, press Done key. The changed alias appears in the list of available aliases. There is no possibility to have two Additional Address items with the same Additional Address Alias. 4.3.10.6 Deleting Additional Address Prerequisites: Deleting Additional Address is allowed only for User-Defined positions. Pre-Defined positions can only be Selected and Viewed. Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Additional Address Select Address. 3 Scroll to select the alias of the Additional Address you wish delete. 4 Press the Menu key. 5 Select Delete and confirm deletion by the OK key. 4.3.11 Call-Out Availability This menu item enables or disables the Call-Out availability. NOTICE: This feature is only available when enabled by your service provider. 4.3.11.1 Setting Call-Out Availability Procedure:

1 From the home screen, press the Menu key. 2 Select Messages Call-Out Availability. 3 Select one of the following:

Available Not available 4.4 Contacts This menu stores all your contact numbers. Each entry requires the following information:

Name if you store more than one number to one contact, this entry is required. 69 DRAFT MN001488A01-BF (en-US) Main Menu Type each contact must be assigned to one of the following types:

Table 16: Contact Types Contact Icon Description Private Cannot have a speed dial number. Mobile Home Work PABX Other Pickers Indicate more than one number in a contact.

# (number) each contacts entry must contain a number. Speed # accept the default Speed Dial number or change it. 4.4.1 Creating Contacts Procedure:

1 From the home screen, press Contcs. 2 Select [New Contact]. 3 Highlight Name and press Change. Enter the name of your contact and press Ok. 4 Highlight Type and press Change. Select the required type of your contact. NOTICE: You can use the Left and Right Navigation keys to select the type of your contact from the Contact Details screen. 5 Highlight # (number) and press Change. Enter the number of your contact and press Ok. 6 If needed, highlight Speed # and press Change. Enter the speed dial number (1 1000) of your contact and press OK. NOTICE: If the entered number exist, the radio displays Overwrite? message. Press Yes to confirm, or No to enter the speed dial number again. 7 Press Done. You have create a contact with one number. To add additional number repeat steps step 4 step 6. 70 DRAFT MN001488A01-BF (en-US) Main Menu 4.4.2 Editing Contacts Procedure:

1 From the home screen, press Contcs. 2 Highlight the contact you want to edit. 3 Press the Menu key. 4 Press Edit. 5 Highlight one of the following entries and press Change to edit:

Name Type

# (number) Speed #

6 Press Done. 4.4.3 Deleting Numbers Procedure:

1 From the home screen, press Contcs. 2 Select a contact you want to edit. 3 Use Left or Right Navigation keys to choose the required number. 4 Press Menu. 5 Select Delete number. NOTICE: If an entry contains only one number, deleting the number deletes the entry. 6 Press Yes. 4.4.4 Deleting Contacts Procedure:

1 From the home screen, press Contcs. 2 Highlight a contact you want to delete. 3 Press the Menu key. 4 Select Delete contact. 5 Select Yes. 71 DRAFT MN001488A01-BF (en-US) Main Menu 4.4.5 Checking Capacity When and where to use: To see how many numbers are stored in the radio. Procedure:

1 From the home screen, press Contcs. 2 Press the Menu key. 3 Select Capacity. 4 Select one of the following:

Private Phone/PABX Contact 4.4.6 Dialing through the Contact List Procedure:

1 From the home screen, press Contcs. 2 To highlight the required contact, use Up and Down Navigation keys, or enter up to 12 characters of the contact name. 3 If the contact has more than one number, use Left and Right Navigation keys to select the required number. 4 To initiate a simplex call, press the PTT button with a Private number. Otherwise use the Send key to initiate a duplex call. 4.5 Bluetooth This menu activates the Bluetooth feature. See Bluetooth on page 116 for details. 4.5.1 Bluetooth Settings Bluetooth Settings allows you to configure radio settings related to Bluetooth activity. 4.5.1.1 Configuring Bluetooth Settings Procedure:

1 From the home screen, press the Menu key. 2 Select Bluetooth Settings. 3 Select one of the following:

Bluetooth enables/disables Bluetooth. Name edits the name of your radio. This name is visible to other remote devices. Indications enables/disables audible indications played by the radio during Bluetooth actions. 72 DRAFT MN001488A01-BF (en-US) Main Menu Audio determines the audio connection mode for headsets. You can select one of the following:

Power Optimized the Bluetooth audio link is released when there is no active call. This option increases the battery life time, but causes a delay in the call setup time for group calls. This delay may result in lost audio on some headsets. GC Optimized the Bluetooth audio link is kept open all the time. This option ensures that audio during group calls is heard without any delay and the audio link is never lost, but shortens the battery life time. NOTICE: This setting does not affect the Motorola Solutions headset with PTT

(NNTN8143_ or NNTN8191_) as it is always in the GC Optimized mode. 4.5.2 Enabling and Disabling Bluetooth Procedure:

1 From the home screen, press the Menu key. 2 Select Bluetooth Bluetooth: On / Bluetooth: Off. 3 Select On to enable, or Off to disable Bluetooth. When Bluetooth is enabled, the Bluetooth icon appears in the status icon area on the display. However, the Bluetooth icon may not be visible at times, due to other icons with higher priority being displayed in the same icon slot. NOTICE:

Your service provider may configure the radio to automatically disable Bluetooth after entering the home mode. The home mode is a state in which all the following conditions are met: the radio is not in the Discoverable Mode, all active remote devices are disconnected (including file transfer), and scanning for remote devices is not performed. 4.5.3 Pairing Bluetooth Devices with Your Radio Pairing is a process that creates a link between two Bluetooth-enabled devices. Once paired, devices remember each other and every subsequent connection between them is authenticated automatically. When and where to use: To scan for available Bluetooth-enabled devices and to connect with them. Procedure:

1 From the home screen, press the Menu key. 2 Select Bluetooth Add Device. Ensure that the device you want to connect with is in pairing mode. The radio lists available devices that can be paired with your radio. 3 Highlight the required device and select Connect. NOTICE: Press accessory PTT button to improve the connection between the accessory and radio. 4 If needed, enter a PIN code or a passkey. NOTICE: If you enter an incorrect PIN code and the subsequent paring attempts take too long or result in an error message, power the Bluetooth device off and on. The radio accepts 3 logging attempts. 73 DRAFT MN001488A01-BF (en-US) Main Menu 4.5.4 Devices This menu item lists all devices paired with your radio and allows you to perform the following operations:

Connect a device. View and change device details. Disconnect a device. Delete a device. 4.5.4.1 Connecting or Disconnecting Devices Prerequisites: Only pre-approved sensor devices can be used. The service provider is responsible for configuring the radio to work with specific devices. See Add Bluetooth Devices on page 117. Procedure:

1 From the home screen, press the Menu key. 2 Select Bluetooth Devices. 3 Highlight the required device and press Menu/OK. Select Connect/Disconnect. NOTICE:

Depending on languages installed on the radio, some characters in names of devices might not be displayed properly. Radio-initiated automatic reconnection with several remote Bluetooth devices at the same time cannot be guaranteed to be successful in 100%, due to the fundamental nature of Bluetooth. In case the reconnection fails after a power cycle (power off and power on of the radio), reconnect the device manually. 4.5.4.2 Managing Devices Procedure:

1 From the home screen, press the Menu key. 2 Select Bluetooth Devices. 3 Highlight the required device and press the Menu key. Name shows the name of the device (up to 32 characters long). The name is editable only if it has not been pre-set by the service provider. Type displays the device type. This menu item cannot be configured. Access defines how the radio behaves during a reconnection attempt after losing connection to this device:

Automatic the radio connects with the device automatically. NOTICE: On some headsets, you may have to press the "Call" button to trigger reconnection. Ask the radio asks you for confirmation before connecting with the device. Manual the radio connects with the device manually. Never the radio never connects with the device. 74 DRAFT MN001488A01-BF (en-US) Main Menu Delete deletes the device from the paired devices lists. 4.5.5 Disconnecting All Devices When and where to use: To disconnect all remote devices connected to your radio. Procedure:

1 From the home screen, press the Menu key. 2 Select Bluetooth Disconnect All. All devices are disconnected. NOTICE: To disconnect only one device, from the home screen, select Menu Bluetooth Devices, highlight the required device, and press Disconnect. 4.5.6 Setting Indoor Location When and where to use: Indoor Location is used to track radio location while indoors. Your radio receives beacon information from a number of dedicated beacons within range of the radio when Indoor Location is activated. The radio then send the information within a LIP message to the SwMI, and a mapping application will decode the information to calculate the radio location. NOTICE: Your service provider can enable this feature. Procedure:

1 From the home screen, press the Menu key. 2 Select Bluetooth Indoor Location. 3 Select Change. 4 Select On or Off to activate or deactivate Indoor Location. Your radio is now able to detect Bluetooth location beacons when activated. NOTICE: The use of the Indoor Location feature may have a negligible impact on other Bluetooth functionality of your radio. 4.5.6.1 Viewing Detected Beacon Prerequisites: Turn on Indoor Location. If Indoor Location is turned off, the screen displays Service Restricted. Procedure:

1 From the home screen, press the Menu key. 2 Select Bluetooth Indoor Location. 3 Select Beacons Found. 4 Select desired beacon. The screen displays details of the beacon. 75 DRAFT MN001488A01-BF (en-US) Main Menu 4.5.7 Connecting Firearms Devices Prerequisites: Only pre-approved firearms devices can be used. The service provider is responsible for configuring the radio to work with specific devices. See Add Bluetooth Devices on page 117. When and where to use: To select a firearm sensor device for Bluetooth connection. Procedure:

1 From the home screen, press the Menu key. 2 Select Bluetooth Firearms. 3 Highlight your firearm sensor device and press Connect. NOTICE:

Activation code must be sent to the device by third-party application. Radio-initiated automatic reconnection with several remote Bluetooth devices at the same time cannot be guaranteed to be successful in 100%, due to the fundamental nature of Bluetooth. In case the reconnection fails after a power cycle (power off and power on of the radio), reconnect the device manually. The radio is now able to notify the dispatcher when the status of the firearm device changes. If configured, the location (using GNSS) of the radio is reported as well. Once a firearm sensor device is connected, it can be managed from the Devices menu. 4 To disconnect a firearm sensor device, go to the Devices menu and follow the normal device management procedure. 4.6 Browser This menu item activates a WAP browser that allows you to browse the Internet from your radio. See Wireless Application Protocol (WAP) on page 130. 4.7 Man Down NOTICE: This feature is a paid feature. Its tilt exceeds a predefined angle value. Man Down alerts when no movement occurs for a set time or the radio stays at an angle of tilt below a defined value. The radio alerts you when:

No movement is detected in a predefined time interval. In case any of the conditions are met, the radio alerts you with a Man Down pre-alert. If you do not disable the pre-alert condition, the radio switches to the Emergency Operation. For easier localization of the radio, visual and audible indications are started until they are deactivated. If the Emergency Hot Microphone is on, the additional audio indication is not played. To exit Man Down, exit the Emergency Mode by pressing and holding the Exit Soft key, or press the PTT button. 76 DRAFT MN001488A01-BF (en-US) Main Menu 4.7.1 Setting Man Down Procedure:

1 From the home screen, press the Menu key. 2 Select Man Down. 3 Select one of the following:

On Activates the feature. Off Deactivates the feature. 4.8 Security This sub-menu stores all your security settings. 4.8.1 PIN Protect This feature allows you to enable PIN code authentication at the next power on. This code protects your radio against unauthorized use. If you are unable to unlock the radio, you can only send or receive Emergency Calls and adjust the volume level with the Volume Knob. NOTICE: If the radio uses a SIM Card PIN code and you are unable to unlock the radio, you cannot take any action. 4.8.1.1 Protecting the Radio with a PIN Code Procedure:

1 From the home screen, press Menu Security PIN Protect. 2 Select On. 3 Enter 4-digit PIN code. By default it is 0000 (four zeros). NOTICE: To increase security, set your own PIN code. Postrequisites: Each time you turn on the terminal, PIN code is required. 4.8.1.2 Changing PIN Codes Procedure:

1 From the home screen, press the Menu key. 2 Select Security Change Code. 3 Radio prompts for the Old Code. Enter currently used 4-digit security code (default setting is 0000). 4 If the entered code matches the old code, radio prompts for the new code twice. Your radio displays Code Accepted. 77 DRAFT MN001488A01-BF (en-US) Main Menu 4.8.2 Setting Keypad Lock The keypad lock/unlock can be invoked from the radio menu, or by using a predefined menu shortcut. By default, the Power and Emergency buttons are always operative when the keypad is locked. Procedure:

Do one of the following:

Press Menu, and then Left Navigation key. To lock, select MENU Security Keylock Setup Lock Keypad. Use the predefined menu shortcut to unlock. 4.8.2.1 Keypad Lock Notification When the keypad is locked, your service provider can configure one of the following instructions:

None no notification is displayed. Notification Only Keys Locked is displayed. Notification and Instruction Press Menu + Left to lock/unlock keypad is displayed. 4.8.2.2 Setting Automatic Keylock Delay Procedure:

1 From the home screen, press the Menu key. 2 Select Security Keylock Setup Delay. 3 Use Up and Down Navigation keys to change the minutes and press Done. 4.8.2.3 Setting Keylock on Startup Procedure:

1 From the home screen, press the Menu key. 2 Select Security Keylock Setup Start Locked. 3 Select On/Off. 4.8.3 Air Encryption NOTICE: This feature is a paid feature. Air Encryption is a feature that enables encryption of entire communication between the radio and infrastructure, which results in increased security of calls, messages, and data. If configured by your service provider, the radio plays a sound and displays Call & Data Not Encrypted when encryption is on and you receive a clear call (unencrypted). This feature provides service confidentiality between you and the system. 78 DRAFT In the TMO Mode, when Air Encryption is enabled on your radio but cannot be supported due to an infrastructure failure, the following icon appears on the display:

. When encryption is not available in MN001488A01-BF (en-US) Main Menu the DMO Mode, the radio displays:

This menu item allows you only to view air encryption state. 4.8.3.1 Viewing Air Encryption State Procedure:

1 From the home screen, press the Menu key. 2 Select Security AirEncrypt. Your radio displays:

Air Encryption Is Off. Air Encryption Is On. 4.8.3.2 Deleting User Keys Prerequisites: Ensure that the user key deletion is enabled in the codeplug. Procedure:

1 Press Side Button 1 Side Button 1 Side Button 1 Side Button 2 Side Button 2 Side Button 2. IMPORTANT: The key deletion takes up to 30 seconds. During the period, the battery must not be removed. Removing the battery during that period may lead to radio malfunction. Encryption and/or Authentication keys are deleted. The radio enters Temporary Disable state and the service provider must manually restore it. 4.8.4 K Validity Key (K) is a secret key the infrastructure uses to authenticate the radio in the system. It is part of the authentication that provides service confidentiality between your radio and the system. 4.8.4.1 Verifying K Validity Procedure:

1 From the home screen, press the Menu key. 2 Select Security K Validity. 3 Your radio displays:

K is Valid the infrastructure can authenticate your radio. K is Invalid the infrastructure is unable to authenticate your radio. Please call your service provider to restore the key to your radio. 79 DRAFT MN001488A01-BF (en-US) Main Menu 4.8.5 SCK (Air Interface Encryption Class 2) Static Cipher Key (SCK) is a secret key used for the Air Interface Encryption Class 2. It may be used to encrypt calls and data in TMO and DMO. The SCK air interface encryption provides service confidentiality between radios and infrastructure when in TMO, and between radios when in DMO. A radio is capable of being loaded with up to 32 SCKs. Specific keys are used for encrypting the air interface. Any mismatch between radios and/or infrastructure impacts communication only those using the same key as the transmitting party are able to decode and hear the communication. 4.8.5.1 TMO SCK Your service provider can enable SCKs in TMO. The SCKs used in TMO are called TMSCKs. 4.8.5.1.1 Verifying TMSCK Validity When and where to use: To ensure that the TMSCKs in the radio are valid and can be used for the air interface encryption. Procedure:

1 From the home screen, press the Menu key. 2 Select Security TMSCK Validity. 3 The radio displays:

TMSCK is Valid the radio can work encrypted in TMO. TMSCK is Invalid the radio cannot work encrypted in TMO. Please contact your service provider to restore SCKs to your radio. 4.8.5.2 DMO SCK Your service provider can enable SCKs in DMO. The SCKs used in DMO are called DMSCKs. 4.8.5.2.1 Verifying DMSCK Validity When and where to use: To ensure that the DMSCKs in the radio are valid and can be used for the air interface encryption. Procedure:

1 From the home screen, press the Menu key. 2 Select Security DMSCK Validity. 3 The radio displays:

DMSCK is Valid the radio can work encrypted in DMO. DMSCK is Invalid the radio cannot work encrypted in DMO. Please contact your service provider to restore SCKs to your radio. 80 DRAFT 4.8.5.3 Changing DMO SCK IMPORTANT: Changing this setting may cause radios not to operate correctly. MN001488A01-BF (en-US) Main Menu Procedure:

1 From the home screen, press the Menu key. 2 Select Security DMO SCK. 3 Press Next. 4 Radio displays Change to version . 5 Select one of the following:

Yes to change the key. Your radio displays Key version changed. No to leave the key. Your radio displays Code Not Changed. 4.8.6 Covert Mode This feature enables you to completely shut down all visible and audible alerts and notifications making the radio unnoticeable even in a silent and dark environment. When your radio is in the Covert Mode, you cannot enter the following menu items of the Setup menu. Set Volume Tones Backlight (in Display menu item) When the Covert Mode is turned on:

All tones are set to Off (corresponding to All Tones menu entry). Group audio is set to Spkr Cntrl (corresponding to Audio Toggle menu entry). The private speaker is set to Off (this setting causes all the calls are routed through the earpiece). Backlight is set to Disabled (corresponding to Backlight menu entry). The LED indicator is switched off. The radio powers up in the mode set before turning off. Thus if the Covert Mode was set before turning off, the radio turns on in the Covert Mode . When the Covert Mode is turned off, all the changed settings are reverted to the previous state. This feature can be used as the One-Touch Button. 4.8.6.1 Activating Covert Mode Procedure:

1 From the home screen, press the Menu key. 2 Select Security Covert Mode. 3 Select one of the following:

On all tones are set to off, and the backlight and the LED are disabled immediately. The group audio is routed to the earpiece. The radio displays Covert Mode On. 81 DRAFT MN001488A01-BF (en-US) Main Menu Off all settings for tones, backlight and audio are restored. The radio displays Covert Mode Off. 4.8.6.2 Setting Vibrate in Covert Mode Procedure:

1 From the home screen, press the Menu key. 2 Select Security Covert Mode Vibrate. 3 Select one of the following:

On To restore all vibrations. Off To disable all vibrations. 4.8.7 Remote Control There are two types of remote control, Short Data Service (SDS) Remote Control and Status Remote Control. 4.8.7.1 Status Remote Control Status Remote Control is a feature that provides limited control of the radio, unlike Short Data Service

(SDS) Remote Control. NOTICE: Only one type of remote control can be active on a radio; either SDS or Status. The following tasks can be assigned remotely to a radio:

Play loud tone until user interaction The radio plays a loud tone as in the Man Down feature until you unlock the keypad (if needed) and press the appropriate soft key labeled Exit. The tone is played through the speaker even if an accessory is attached. NOTICE: The tone is not emitted when the radio is in one of the following states:

In a call Temporarily disabled Pseudo Off Mode Ambience Listening Mode Transmit Inhibit Mode (TXI) Emergency Mode Silent Emergency Mode Covert Mode Send firmware version and TEI The radio sends back an SDS message with its firmware version and TEI. NOTICE: If the sending Individual Short Subscriber Identity (ISSI) is not on the Allowed ISSIs list, the receiving radio ignores the task. 82 DRAFT MN001488A01-BF (en-US) Main Menu 4.8.7.2 SDS Remote Control NOTICE: This feature is a paid feature. NOTICE: Only one type of remote control can be active on a radio; either SDS or Status. SDS Remote Control is a feature that enables remote control and configuration of the radio via special SDS messages. The messages can be sent both in TMO and DMO (including the Repeater Mode) by any radio capable of controlling other radios. During the execution of the Remote Control messages, depending on your service provider settings, the radio can play a tone or display an appropriate icon in the status icon area. 4.8.7.3 Setting Remote Control This procedure describes how to toggle remote control. Procedure:

1 From the home screen, press the Menu key. 2 Select Security Remote Control. 3 Select On to enable, or Off to disable remote control. 4.9 Setup This sub-menu allows you to change your radio configuration. 4.9.1 Vibrate This sub-menu allows you to determine if your radio vibrates, or rings, or vibrates and then rings when receiving a call. 4.9.1.1 Setting Default Vibrate Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Vibrate. 3 Select one of the following:

Vibe then Ring Vibe Only Ring Only 83 DRAFT MN001488A01-BF (en-US) Main Menu 4.9.1.2 Setting Detail Vibrate Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Vibrate Custom.... 3 Select one of the following:

Duplex Calls Sets the vibrate settings for Phone, PABX, and Duplex Private calls. Simplex Calls Sets the vibrate settings for Simplex Private Calls. Group Call Sets the vibrate settings for Group Calls. Mail Rcvd Sets the vibrate settings for status messages and text messages. 4 Select the required setting, and press Select. NOTICE:

If you choose Group Call, the settings available are:

Vibe On, Vibe Off. 4.9.2 Ring Style This sub-menu allows you to set the incoming call ring style. 4.9.2.1 Setting Ring Style Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Ring Style. 3 Select one of the following:

Duplex to set the new ring style to all duplex calls. Simplex to set the new ring style to all simplex calls. NOTICE: Upon entry into this sub-menu, the display shows the current ring style used. 4 Scroll to the desired style and press Select. NOTICE: New ring style is played immediately for a few seconds. If necessary, adjust the volume level. 4.9.3 Set Volume This menu item allows you to adjust the Speaker and Earpiece tone volumes. 84 DRAFT MN001488A01-BF (en-US) Main Menu 4.9.3.1 Setting Volume Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Set Volume. 3 Select Speaker or Earpiece. 4 Select one of the following:

Voice Vol sets the volume level for voice. Duplex Vol sets the volume level for duplex ringtones. Simplex Vol sets the volume level for simplex ringtones. Keypad Vol sets the volume level for keypad tones. Tones Vol sets the volume level for alert tones. Call-Out Vol sets the volume level for Call-Out tones (if enabled). NOTICE: If the display shows only one option Volume, you can adjust all of the above settings at once. You have the option to change the settings individually when the Volume Adj. Mode is set to Individual. 5 Press Right or Left Navigation key to change the value. NOTICE: When the battery level is low it is not recommended to attach the 4 speaker to the radio as it can cause reset or shutdown of the radio. 4.9.4 Language This sub-menu allows you to change the language of the radio. 4.9.4.1 Setting Language Prerequisites: The list of available languages is set by service provider. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Language. 3 Select desired language. 4.9.5 Data Setup This menu item allows you to set up your radio to transmit and receive data from the external device. To connect your radio accessory connector to the external device, use the PMKN4127 or PMKN4129 cable. The external device must run an application complying with the TETRA standards. NOTICE:

Data services are available only in TMO Mode. Data services are blocked in TXI Mode. When set to Voice Only, the built-in data modem is disabled to conserve battery power. 85 DRAFT MN001488A01-BF (en-US) Main Menu 4.9.5.1 Setting Data Function Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Data Setup. 3 Select one of the following:

Voice Only Your radio receives and transmits voice calls only. Data Only Your radio acts as a modem. It rejects incoming and outgoing voice calls

(except for Emergency Calls), status and text messages. Voice & Data Your radio acts as a modem but voice calls have priority over data calls and can interrupt them. 4.9.6 Audio This menu item allows you to adjust your radio audio settings. 4.9.6.1 Audio Profiles An audio profile is a set of audio parameters, such as the volume of alert tones, that are configured by your service provider to fit a particular operating environment. For example, the audio parameters can be adjusted to situations when the radio operates inside a building or on a noisy street. Your service provider can configure a maximum of five audio profiles. For a detailed description of a specific audio profile, contact your service provider. 4.9.6.1.1 Setting Audio Profiles When and where to use: To adjust the audio parameters of the radio in its current operating environment. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Audio Audio Profile. 3 Select a required profile. 4.9.6.2 Howling Suppression The howling suppression is a mode increasing the stability of the acoustic feedback loop. The radio eliminates howling caused by the feedback loop from the receiving radios to the sending radio in simplex calls. You can toggle the howling suppression during an active call. To enable this anti-howling function, you can either use the radio menu or the corresponding One-

Touch Button. 86 DRAFT MN001488A01-BF (en-US) Main Menu 4.9.6.2.1 Setting Howling Suppression Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Audio Howling Suppr.. 3 Select required setting. NOTICE: Your service provider can set up the state of the howling suppression on powering up the radio. Depending on the settings, the radio can either disable the howling suppression or set the last remembered state. 4.9.6.3 Audio Toggle You can control audio routing between the speaker and earpiece for any private or group call through the dedicated Speaker Control key. You can also define through the menu to have all group calls in high audio or controlled by the Speaker Control key. 4.9.6.3.1 Setting Audio Toggle Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Audio Audio Toggle. 3 Select one of the following:

Always Loud The audio sound comes from the speaker (high audio only). Spkr Cntrl The audio goes through the earpiece or the speaker. 4.9.6.4 Volume Adjustment Mode You can set the volume to Individual or Common. When it is set to Individual, the volume level for Voice, Duplex, Simplex, Keypad, Tones, and Call-Out can be set per user preferences. When set to Common, the audio has one setting for all items. The Volume Control Mode is configurable using the Customer Programming Software (CPS). NOTICE: When a volume control capable Bluetooth device is connected, the radio always uses the Common setting. The max volume offset (dB) and the volume range (dB) are configurable through CPS (Audio Settings User Profile). The volume control in the radio is divided into 13 steps, from 0 to 14. If, for example, the vol. range is set to 39, each step on the volume indication bar is 3 dB. 4.9.6.4.1 Setting Volume Adjustment Mode Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Audio Volume Adj. Mode. 3 Select one of the following:

87 DRAFT MN001488A01-BF (en-US) Main Menu Individual You can set Duplex, Simplex, Earpiece, Speaker, and Keypad per your preferences in Menu Setup Set Volume. Common You can set one value for all the items in Menu Setup Set Volume. 4.9.7 Tones This field sets the volume level for the tones set. NOTICE: The radio has two tone packs: Classic Tones (default) and New Tones. Your service provider decides which tone pack is enabled. 4.9.7.1 Keypad Tone You can activate/deactivate keypad tone at every key press. 4.9.7.1.1 Setting Keypad Tone Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Tones Keypad Tone. 3 Select one of the following:

On Activates keypad tone. Off Deactivate keypad tone. 4.9.7.2 All Tones You can activate/deactivate all tones. 4.9.7.2.1 Setting All Tones Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Tones All Tones. 3 Select one of the following:

On Activates all the tones. Off Deactivates all the tones. 4.9.7.3 Talk Permit You can activate/deactivate the tone heard upon pressing the PTT button. 88 DRAFT MN001488A01-BF (en-US) Main Menu 4.9.7.3.1 Setting Talk Permit Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Tones Talk Permit. 3 Select one of the following:

Tone On Tone heard upon pressing the PTT button. Tone Off No tone heard upon pressing the PTT button. 4.9.7.4 Clear to Send You can activate/deactivate tone for the transmitting radio that the receiving radio is ready to accept the transmission. 4.9.7.4.1 Setting Clear to Send Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Tones Clear to send. 3 Select one of the following:

Tone On Activate clear to send tone. Tone Off Deactivates clear to send tone. 4.9.7.5 Periodic Alert You can activate/deactivate periodic tone indication for the missed calls, the unread messages, and low battery level. For each notification, your radio generates an unread message tone with the amber LED color indication. 4.9.7.5.1 Setting Periodic Alert Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Tones Periodic Alert. 3 Select one of the following:

Alert Activates/deactivates periodic tone. Period Indicates the time between each periodic tone. 4.9.7.6 D-PTT Tones This menu item contains the settings for the Double PTT feature. 89 DRAFT MN001488A01-BF (en-US) Main Menu The Double PTT feature allows you to send a tone pattern (single, double, or triple) when the radio is in idle or the Group Call mode by pressing the PTT button twice. After the D-PTT tone is played, you can press and hold the PTT button once again to get the permission to talk. Otherwise, if you press the PTT button while the D-PTT tone is played, it is ignored. After the D-PTT tone is sent, keeping the PTT button pressed results in permission to talk. The D-PTT tone is sent over the air but is not audible on the sending radio. 4.9.7.6.1 Setting D-PTT Tones Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Tones D-PTT Tones. 3 Select one of the following:

D-PTT Mode Activates/deactivates D-PTT tone. Tone Style Indicates how many times the D-PTT tone is played. 4.9.8 Display This menu item allows you to adjust your radio display settings. 4.9.8.1 Setting Flip Display When and where to use:

The feature is useful for a user who has to wear the radio on a shoulder, belt, or lapel and at the same time wishes to read the display upside down. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Display Flip Display. 3 Select one of the following:

On to activate this feature. Off to deactivate this feature. 4.9.8.2 Setting Font Level When and where to use: To increase or decrease text size so you can adjust the interface readability to existing conditions. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Display Font Level. 3 Select one of the following:

1 default size of the text. 2 large size of the text. Keep in mind that less text can be displayed. 90 DRAFT MN001488A01-BF (en-US) Main Menu In some languages, the number of available font levels can be decreased. 4.9.8.3 Setting Large Idle Font When and where to use: To enable/disable large font on the home screen. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Display Large Idle Font. 3 Select On to enable, or Off to disable displaying large font on the home screen. NOTICE: Large Idle Font is not available in some languages. 4.9.8.4 Setting Screen Saver Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Display Screen Saver. 3 Select one of the following:

Activate To activate or deactivate this feature. Select one of the following sub-options:

Auto Automatically displays the screen saver when the radio is inactive for a pre-

determined period. Disabled Disables the screen saver. Text To set the text on the screen saver when this feature is activated. 4.9.8.5 Setting Backlight When and where to use: To save the battery power. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Display Backlight. 3 Select one of the following:

Auto backlight is triggered by turning on the radio, by pressing any key on the device or on the accessory that is connected to it. Also charging or getting signal from the services like:

Call-Out message, RUA request, DGNA, TX timeout during priority call, and new SDS messages are going to turn on the backlight. Semi Auto backlight is turned on when you are switching on the radio, pressing assigned button to the backlight feature, or charging. Disabled backlight is disabled and the display is always dimmed. 91 DRAFT MN001488A01-BF (en-US) Main Menu 4.9.8.6 Setting Brightness When and where to use: To set the luminance of the display and the keypad in an environment with low visibility. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Display Brightness. 3 Manually adjust the brightness level using the Left or Right Navigation key. 4.9.8.7 Setting LCD Off When and where to use: This feature sets the time so the display automatically turns off after a specific amount of time. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Display LCD Off. 3 Select one of the following:

Disabled your radio display never goes off. 30 seconds turns off the radio display after 30 seconds. 1 minute turns off the radio display after 1 minute. 2 minutes turns off the radio display after 2 minutes. 5 minutes turns off the radio display after 5 minutes. 15 minutes turns off the radio display after 15 minutes. 30 minutes turns off the radio display after 30 minutes. 4.9.8.8 Setting Wallpaper When and where to use: To change the look of the home screen. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Display Wallpaper. 3 Select one of the following:

On To activate this feature. Off To deactivate this feature. 4.9.9 Time and Date The Time and Date feature is triggered by the One-Touch Button. This sub-menu controls the displayed time and date on the home screen. 92 DRAFT MN001488A01-BF (en-US) Main Menu NOTICE: Infrastructure synchronizes the time and date. When not within the infrastructure signal range you can set the values manually. 4.9.9.1 Setting the Time Format Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Time & Date Format Format Time. 3 Select one of the following:

12-Hour Displays the time with am (before noon) or pm (after noon) indication. 24-Hour Displays the time in 24 hour format. 4.9.9.2 Setting the Time Manually When and where to use: If the time cannot update automatically through the infrastructure. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Time & Date Set Set Time. 3 Enter current time using Navigation keys. 4 Press Done. 4.9.9.3 Setting the Date Format Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Time & Date Format Format Date. 3 Select (D day, M month, Y year):

DD/MM/YY MM/DD/YY DD-MON-YY YY/MM/DD 4.9.9.4 Setting the Date Manually When and where to use: If the time cannot update automatically through the infrastructure. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Time & Date Set Set Date. 3 Enter current time using Navigation keys. 4 Press Done. 93 DRAFT MN001488A01-BF (en-US) Main Menu 4.9.9.5 Setting Time Offset Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Time & Date Set Time Offset. 3 Enter time offset using Navigation keys. NOTICE: You can adjust the offset value, with 15 minute steps, up to 14 hours ahead or behind. 4 Press Done. 4.9.9.6 Setting Automatic Updates for the Time and Date Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Time & Date System Update. 3 Select one of the following:

Off All the infrastructure information are ignored. The radio uses internal time and offset. Time Only Time displayed is calculated from the offset programmed by your service provider added or subtracted from the infrastructure time. Time & Offset Time and offset are updated after receiving from the infrastructure. 4.9.10 Energy Economy Energy Economy (EE) is a mode of operation to save battery life. Your radio does not monitor all downlink time slots of the Main Control Channel. If the radio is in the charger, Energy Economy mode is not needed. 4.9.10.1 Enabling or Disabling Energy Economy Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Energy Economy EE Selection. 3 Select one of the following:

On Activates Energy Economy feature. Off Deactivates Energy Economy feature. 4.9.10.2 Viewing the Energy Economy Status Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Energy Economy EE Status. 94 DRAFT MN001488A01-BF (en-US) Main Menu 3 The Energy Economy status is displayed as:

Energy Ecnmy Is Supported By System Energy Economy Is Currently Not Supported By System 4.9.11 Transmission Power Class NOTICE: This feature is a paid feature. Transmission Power feature enables your radio to choose whether to transmit with Class 3L or Class 4. The RF Power icon indicates when the radio uses this feature. 4.9.11.1 Selecting RF Power Use this procedure when you are entering the area that requires higher signal strength. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup RF Power. 3 Select one of the following:

Hi RF Power Activates this feature. Normal RF Pwr Deactivates this feature. NOTICE:

Changing RF Power Class to Normal RF Pwr during calls may result in dropping the call. The power level may be not sufficient to sustain the transmission. Battery consumption is higher when Hi RF Power is selected. 4.9.12 Accessory (Accry) Setup You can connect IMPRES, CORE, Other, or Secondary accessories to the radio side connector. If you connect an IMPRES accessory, the radio detects and recognizes the accessory automatically. If you connect a CORE, Other (for example, a third-party accessory), or Secondary accessory (for example, an earpiece connected to an RSM), the radio may detect the connection but manual selection is required at the Accry Setup menu. The Accry Setup menu contains the supported accessories, represented by their Model Number as defined by the related Audio Device Descriptor (ADD). ADD is a set of parameters in the radio that defines the audio settings, such as gains and filters settings, for each accessory. IMPORTANT: Do not connect RSMs to both connectors at the same time. To ensure correct connection, do not press any RSM buttons when connecting the RSM to the radio. 4.9.12.1 Selecting CORE/Other/Secondary Accessories Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Accry Setup. 95 DRAFT MN001488A01-BF (en-US) Main Menu 3 Select one of the following:

CORE RSM/PHF select an accessory from the list of the CORE accessories. CORE Earpiece select an earpiece from the list of the CORE accessories. RSM Earpiece specify if the accessory is connected to the RSM. Bluetooth Headset select an accessory from the list of available Bluetooth headsets. 4.9.13 Book On This menu item allows you to edit RUA/RUI feature settings to automatically accept or reject book on requests. 4.9.14 Rotary Knob This menu item allows you to set all the related functionality of the Volume Knob and Talkgroup Knob. 4.9.14.1 Setting Rotary Lock Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Rotary Knob Rotary Lock. 3 Select one of the following:

Locked Locks Volume Knob and/or Talkgroup Knob. Unlocked Unlocks the Volume Knob and Talkgroup Knob. Disabled Locking function is unavailable. Your Volume Knob and Talkgroup Knob is unlocked all the time. 4.9.14.2 Setting In Keypad Lock When and where to use: To set behavior of the rotary knob when the keypad is locked. Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Rotary Knob In Keypad Lock. 3 Select one of the following:

Lock None Scrolling and volume setting functionality is available. Lock Volume Talkgroup Knob can be only used for scrolling. Lock Scroll Volume Knob can be only used for setting the volume. Lock Both Scrolling and volume setting functionality is unavailable. 96 DRAFT MN001488A01-BF (en-US) Main Menu 4.9.14.3 Setting Rotary Knob Wrap Around Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Rotary Knob Wrap Around. 3 Select one of the following:

On Scrolling through the talkgroup list is looped or is moved to the next folder. Off Scrolling through the talkgroup list stops after reaching first or last talkgroup in the current selected folder. NOTICE: Only when Wrap Around is set to On and the Scroll Range is set to Scroll To Next, you are able to scroll through all the talkgroups and folders. 4.9.14.4 Setting Rotary Knob Scroll Range Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Rotary Knob Scroll Range. 3 Select one of the following:

Stay In Range Scrolling through the talkgroups in the current folder only. Scroll To Next Scrolling through all the talkgroups and folders. NOTICE: Only when Wrap Around is set to On and the Scroll Range is set to Scroll To Next, you are able to scroll through all the talkgroups and folders. 4.9.14.5 Setting Rotary Knob Talkgroup Selection Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Rotary Knob Confirm TG Sel.. 3 Select one of the following:

On You need to confirm the talkgroup selection by pressing Select or pressing the PTT button to immediately start a call on a new talkgroup. Off Attaches to the selected talkgroup without any additional prompt. 4.9.14.6 Setting Rotary Knob Function Keys Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Rotary Knob Function Keys. 3 Select one of the following:

Auto Sets the Side buttons according to the Rotary Mode. 97 DRAFT MN001488A01-BF (en-US) Main Menu NOTICE: If the Rotary Mode is set to:

Dual or Volume Display shows Auto Selected (OTB), volume can be set only through Volume Knob. Scroll Display shows Auto Selected (Volume), volume can be set only through Side buttons. Volume Adjust. Sets the Side buttons to adjust volume level. OTB Feature Sets the Side buttons to the predefined One-Touch Button features. 4.9.15 Default Setting This sub-menu item resets the radio back to default settings. 4.9.15.1 Selecting Default Setting Procedure:

1 From the home screen, press the Menu key. 2 Select Setup Def. Settings. Your radio display Reset to def. settings?. Press Yes to confirm. 4.10 Group Setup This menu item allows you to set the operation parameters, scanning and my groups folder. 4.10.1 Setting Operations Parameters When and where to use: If you want to define the radio mode and the talkgroup at the radio startup, and when changing modes TMO DMO and TMO Repeater. Procedure:

1 From the home screen, press the Menu key. 2 Select Group Setup Operations Parameters. 3 Select Startup. Select one of the following:

TMO the radio powers up in TMO mode. DMO the radio powers up in DMO mode. Last Selected the radio powers up in the mode it was in when last powered down. 4 Select Home Group Startup. Select one of the following:

Last Selected the radio enters the TMO/DMO talkgroup which was last selected before power down. Home Group the radio enters the Home Group (TMO or DMO) at power up, depending on the radio mode entered at power up. 5 Select HGr TMO DMO/Rep. Select one of the following:

98 DRAFT MN001488A01-BF (en-US) Main Menu Last Selected when changing modes the radio enters the DMO Talkgroup last selected, for example the DMO Talk Group active last time the Radio was in DMO Mode. If Group Mappings are configured, they will take precedence and the DMO Talkgroup mapped to the current TMO Talkgroup is used. Group Mappings when changing modes the radio enters the DMO Home Group unless a Group Mapping is configured. If Group Mappings are configured, they will take precedence and the DMO Talkgroup mapped to the current TMO Talkgroup is used. Home Group when changing modes the radio enters the DMO Home Group, ignoring possible group mappings. 6 Select TMO Home Group configures the TMO Home Group/Home Folder. 7 Select DMO Home Group configures the DMO Home Group. 4.10.1.1 Standard Home Group This menu item allows you to configure the standard home group to be used during start up and when changing modes: TMO DMO and TMO Repeater. 4.10.2 Scan This menu item allows you to activate/deactivate scanning, view the active scan list, and edit the scan lists. This feature is available only for the TMO Mode. Your radio joins any group call as long as this group is defined in the scan list and scan is turned on. 4.10.2.1 Activating Talkgroup Scanning When and where to use: If you want to monitor any TMO Group Call in the defined talkgroup list. Procedure:

1 From the home screen, press the Menu key. 2 Select Group Setup Scan Scanning. 3 Select Select List and then a list name. Your radio displays list name selected. 4 Select Scanning On. Your radio is scanning on the predefined scan list. 4.10.2.2 Setting Talkgroups in the Active Scan List When and where to use: If you want to edit talkgroups in the active scan list. Procedure:

1 From the home screen, press the Menu key. 2 Select Group Setup Scan Active List. NOTICE: If Scanning is Off is displayed, go to Group Setup Scan Scanning On to enable scanning. 3 Select View and highlight the required talkgroup. 99 DRAFT MN001488A01-BF (en-US) Main Menu 4 Press Menu. 5 Select one of the following:

Delete Erases this group from the active scan list. Priority and select new priority to Low, Medium or High. 4.10.2.3 Setting Scan Lists When and where to use: If you want to set up any scan list. Procedure:

1 From the home screen, press the Menu key. 2 Select Group Setup Scan Scan Lists. 3 Highlight required scan list and press Menu to see additional settings:

Capacity Displays the number of assigned and unassigned talkgroups for the scan list. Clear Deletes all the talkgroup assigned to that scan list. Add Group Adds a talkgroup to the scan list. Select one talkgroup from your talkgroup folders and assign appropriate priority. Edit Changes the priority of the required talkgroup or deletes it. 4.10.2.4 Deleting Talkgroups from Scan Lists Procedure:

1 From the home screen, press the Menu key. 2 Select Group Setup Scan Scan Lists. 3 Highlight the required scan list and press Menu Edit. 4 Highlight the required talkgroup and press Menu Delete. 4.10.3 My Groups This sub-menu allows you to select/edit your favorite group list. 4.10.3.1 Adding Favorite Folders Procedure:

1 From the home screen, press the Menu key. 2 Select Group Setup My Groups. 3 Select [New Folder]. 4.10.3.2 Adding Talkgroups to Favorite Folders Procedure:

1 From the home screen, press the Menu key. 100 DRAFT MN001488A01-BF (en-US) Main Menu 2 Select Group Setup My Groups. 3 Select <FolderName>. 4 Select [New Group]. 5 Select the required talkgroup by Folder or by alphabetic search. 4.10.3.3 Deleting Favorite Folders Procedure:

1 From the home screen, press the Menu key. 2 Select Group Setup My Groups. 3 Highlight a required favorite folder. 4 Press the Menu key. 5 Select Delete Folder. Press Yes to confirm deletion. NOTICE: You cannot delete the last favorite folder. 4.10.3.4 Deleting Talkgroup from Favorite Folders Procedure:

1 From the home screen, press the Menu key. 2 Select Group Setup My Groups. 3 Select required favorite folder. 4 To delete one talkgroup, highlight it and select Delete. NOTICE: To delete all the talkgroups from the folder, press Menu and select Delete All. 4.11 Individual Setup This menu item allows you to set call settings for individual calls. 4.11.1 Trunked Mode This sub-menu allows you to set call waiting and call forwarding for your radio. 4.11.1.1 Enabling or Disabling Call Waiting When and where to use: To enable or disable Call Waiting for your radio. Procedure:

1 From the home screen, press the Menu key. 2 Select Individual Setup Trunked Mode Call Waiting. 3 Select On to enable Call Waiting, or Off to disable it. 101 DRAFT MN001488A01-BF (en-US) Main Menu 4.11.1.2 Setting Call Forwarding When and where to use: To enable or disable Call Forwarding for your radio. If radio is not in TMO mode, selecting call forwarding will results in an Invalid Keypress tone and Service Restricted message. Procedure:

1 From the home screen, press the Menu key. 2 Select Individual Setup Trunked Mode Call Forwarding. 3 Select one of the following:

Config Sending Enable or disable call forwarding. Select On to enable call forwarding. Config Set predefined condition messages for calling radio. You can select more than one messages:

Always Busy No Answer Not Reachable NOTICE: The settings in the Config sub-menu is only enabled when On is selected in Enable Config. Last Result Display the radio's response of the last sent call forwarding. 4.12 Favorites Favorites contains shortcuts to frequently used talkgroups and contact numbers that are organized in favorite folders. To quickly access favorite folders, from the home screen press the Up Navigation key. To scroll through items inside favorite folders, you can either use the Navigation keys or the Rotary Knob. 4.12.1 Adding Folders to Favorites Prerequisites: Favorites contains less than three favorite folders. Procedure:

1 From the home screen, press the Menu key. 2 Select Favorites [New Folder]

4.12.2 Adding Contact Numbers to Favorites Procedure:

1 From the home screen, press the Menu key. 2 Select Contacts 3 Highlight a contact that you want to add to Favorites and using the Left or Right Navigation key select the required number. 102 DRAFT MN001488A01-BF (en-US) Main Menu 4 Press the Menu key and select Add to Favorites. 5 Select a folder you want to add the contact number to and press Select. 4.12.3 Making Private Calls to Favorite Contact Numbers Procedure:

1 To select a contact number you want to call, from the home screen do one of the following:

Press the Up Navigation key. Go to Options TG by Folder, select the required favorite folder, and highlight the contact number. 2 When you are in the following mode:

TMO For a simplex call, press and release the PTT button. You hear a ringing tone. Otherwise, press and hold the PTT button. Wait for the Talk Permit Tone before talking, and release the PTT button to listen. For a duplex call, press and release Send key. You hear a ringing tone. DMO Only simplex call is available. Press and hold the PTT button. Wait for the Talk Permit Tone before talking, and release the PTT button to listen. 3 To end the call, press the End key. 4.12.4 Adding Talkgroups to Favorites Prerequisites:

To add a DMO talkgroup, ensure that the radio is in DMO. To add a TMO talkgroup, ensure that the radio is in TMO. Procedure:

1 From the home screen, press Options. 2 Select one of the following:

TG by Folder contains talkgroups arranged by folders. TG by abc contains talkgroups arranged alphabetically. 3 Find and highlight a talkgroup that you want to add to Favorites. 4 Press the Menu key and select Add to Favorites. 5 Select a folder you want to add the talkgroup to and press Select. 4.12.5 Managing Folders in Favorites Procedure:

1 From the home screen, press the Menu key. 2 Select Favorites. 3 Highlight a required folder. 4 Press the Menu key. 103 DRAFT MN001488A01-BF (en-US) Main Menu 5 Select one of the following:

Rename Folder changes the name of the folder. Enter a new folder name and press OK. Delete Folder removes the selected folder from Favorites. Press Yes to confirm deletion. NOTICE: You cannot delete the last favorite folder or a folder that contains at least one non-erasable item. 4.12.6 Deleting Folders in Favorites Procedure:

1 From the home screen, press the Menu key. 2 Select Favorites. 3 Highlight a required folder. 4 Press the Menu key. 5 Select Delete Folder. 6 Confirm the deletion by pressing Yes. NOTICE: You cannot delete the last favorite folder or a folder that contains at least one non-erasable item. 4.12.7 Deleting Items from Favorites Folder When and where to use: To delete a single contact number or a talkgroup from a favorite folder. Procedure:

1 From the home screen, press the Menu key. 2 Select Favorites. 3 Select a folder containing the item you want to remove. 4 Highlight the item and select Delete. 5 Confirm the deletion by pressing Yes. 4.12.8 Deleting All Items from Favorite Folders When and where to use: To delete all contact numbers and talkgroups stored in a favorite folder. Procedure:

1 From the home screen, press the Menu key. 2 Select Favorites. 3 Select a required folder. 4 Press the Menu key and select Delete All. 5 Confirm the deletion by pressing Yes. 104 DRAFT MN001488A01-BF (en-US) Main Menu 4.13 My Info This sub-menu allows you to view your own private, phone, and radio info. 4.13.1 Viewing Personal Information Procedure:

1 From the home screen, press the Menu key. 2 Select My Info. 3 Select one of the following:

My Private Num displays your radio private number. My Phone Num displays your radio phone number. Radio Info displays radio information: manufacturer, product type, ISSI, TEI, and Serial Number. 4.14 Recent Calls You can view the history of all calls:

Dialed calls you initiated. Received calls you answered. Missed calls you received but not answered or rejected. Each list of calls may contain up to 50 numbers, the most recent call being at the top of the list. If the number of a recent call is stored in the contact list, the name associated with the number appears in the recent calls list. A number dialed more than once, appears only once in the list. NOTICE: Calls missed in TXI mode are stored and can be viewed. 4.14.1 Viewing Recent Calls Procedure:

1 From the home screen, press the Menu key. 2 Select Recent Calls. 3 Select one of the following:

Dialed Received Missed 4 Select a required call from the list. 5 Press the Menu key. 6 Select View. 105 DRAFT MN001488A01-BF (en-US) Main Menu NOTICE: Press Down Navigation key to bypass first two steps. Call time information is only available if the time and date are set in the radio. Call duration is not available in the missed calls list. 4.14.2 Calling from Recent Calls Procedure:

1 From the home screen, press the Menu key. 2 Select Recent Calls. 3 Select one of the following:

Dialed (from the home screen press Send key to access Dialed Calls list) Received Missed NOTICE: From the home screen press Down Navigation key, to access Recent Calls menu item. 4 Highlight the required call and press PTT button for private calls or press Send key for phone call. NOTICE: Phone calls are only available in TMO Mode. 4.14.3 Storing Recent Calls to Contacts Procedure:

1 From the home screen, press the Menu key. 2 Select Recent Calls. 3 Select one of the following:

Dialed Received Missed 4 Press Store. NOTICE: If Store is not assigned to the Left Soft key, the number is already stored in your contact list. 5 Do one of the following:

To store the number as a new entry, select [New Contact]. To store the number to an existing entry, select the entry, and press View then select Edit. 6 With the contact type field highlighted, scroll left or right to display the contact type you want to assign the number. 7 Select Done. 106 DRAFT MN001488A01-BF (en-US) Main Menu 4.14.4 Deleting Recent Calls Procedure:

1 From the home screen, press the Menu key. 2 Select Recent Calls. 3 Select one of the following:

Dialed Received Missed 4 Press Menu on the required call. 5 Select Delete. NOTICE: To erase all the calls, select Delete All. 4.15 Networks This menu item allows you to switch between the radio operation modes. 4.15.1 Selecting Network Operation Mode Procedure:

1 From the home screen, press the Menu key. 2 Select Networks. 3 Select one of the following:

Network Sel Selects the network to which the radio is allowed to register. Trunked Mode Switches to the mode using infrastructure. Direct Mode Switches to the mode without using infrastructure. TXI Mode Select Activate to stop sending any radio transmission. NOTICE: If the radio is in TXI Mode, it is not possible to switch from Direct Mode to Trunked Mode. TG Net Sel Selects one or multiple networks determined by the selected talkgroup. 107 DRAFT MN001488A01-BF (en-US) Main Menu 4.15.2 Network Select This sub-menu item allows you to select a network to register your radio. Network Sel is available only in TMO or Gateway mode, otherwise your radio display Service Restricted message. 4.15.2.1 Selecting Your Network Procedure:

1 From the home screen, press the Menu key. 2 Select Networks Network Sel Home Only. Your radio registers to the home network. 4.15.2.2 Using Select Net Registration Use this feature to migrate to another predefined network when you are out of the range of your network and your radio displays the No Service message. Procedure:

1 From the home screen, press the Menu key. 2 Select Networks Network Sel Select Net. 3 Select the required network from the list. Your radio registers to the selected network. 4.15.3 Talkgroup Network Select This sub-menu item allows you to select one or multiple networks to register your radio accordingly to the selected talkgroup. TG Net Sel is available when the selected talkgroup is a Any Net talkgroup or a InterSystem Interface (ISI) talkgroup, otherwise your radio display Service Restricted message. 4.15.3.1 Selecting Your Talkgroup Network Procedure:

1 From the home screen, press the Menu key. 2 Select Networks TG Net Sel Home Only. Your talkgroup registers to the home network. 4.15.3.2 Using Select TG Net Registration When and where to use: If the talkgroup selected is an Any Net talkgroup, this menu displays multiple networks allowed for registration. If the talkgroup selected is an ISI talkgroup, this menu displays 108 DRAFT MN001488A01-BF (en-US) Main Menu multiple talkgroup linked networks. Use this feature to migrate to another predefined network, when you are out of the range of your network and your radio displays the No Service message. Procedure:

1 From the home screen, press the Menu key. 2 Select Networks TG Net Sel Select TG Net. 3 Select the required network from the list. 4.15.3.3 Using Prefer TG Net Registration If the talkgroup selected is an Any Net talkgroup, this menu displays multiple networks allowed for registration. If the talkgroup selected is an ISI talkgroup, this menu displays multiple talkgroup linked networks. Use this feature to select a network that is most preferred. The selected network is the first priority for scanning and registration. Procedure:

1 From the home screen, press the Menu key. 2 Select Networks TG Net Sel Prefer TG Net. 3 Select the required network from the list. 4.15.3.4 Using Any TG Net Registration When and where to use: Your radio has lost its network coverage and wants to increase the number of networks it can scan and register. If the talkgroup selected is an Any Net talkgroup, this menu displays all networks allowed for scanning and registration. If the talkgroup selected is an ISI talkgroup, this menu displays all talkgroup linked networks allowed for scanning and registration. Procedure:

1 From the home screen, press the Menu key. 2 Select Networks TG Net Sel Any TG Net. Your radio selects and registers to the network automatically from the predefined list. 4.16 Location NOTICE: This feature is a paid feature. This sub-menu allows you to enable the GNSS, change GNSS accuracy, and view your position and testpage. See Global Navigation Satellite System (GNSS) Location Service on page 121. 4.16.1 Enabling GNSS Procedure:

1 From the home screen, press the Menu key. 2 Select Location Interface. 109 DRAFT MN001488A01-BF (en-US) Main Menu 3 Select On. NOTICE: Your service provider can enable this feature. 4.16.2 Viewing Your Position Procedure:

1 From the home screen, press the Menu key. 2 Select Location Position. 3 Scroll to view the results about the last time your location was calculated. NOTICE: To refresh your position:

Select Position the radio refreshes its position automatically Press Refresh 4.16.3 Viewing Testpage Procedure:

1 From the home screen, press the Menu key. 2 Select Location Testpage. 3 Select one of the following:

Position displays detailed information on radios current position: time, N (latitude), E

(longitude), H (height), Sats Used (a number of tracked satellites), B (bearing), HS

(horizontal speed), LC (level of confidence). Power displays detailed information on a particular satellite: PRN code, Status, Mode, C/N

(carrier-to-noise ratio). Version displays detailed information on software version: SW (software version), HW

(hardware version), ASIC (application-specific integrated circuit), RC (release code). 4.16.4 Changing GNSS Accuracy Procedure:

1 From the home screen, press the Menu key. 2 Select Location Accuracy. 3 Select one of the following:

Medium (default) Power consumption optimization is combined with less position accuracy. High Better position accuracy is combined with less power consumption optimization. NOTICE: If connected to an external charging device, the radio automatically enters the High mode. 110 DRAFT MN001488A01-BF (en-US) Main Menu 4.16.5 Backlog This sub-menu allows you to enable/disable, view, and delete backlog reports. NOTICE: The location report backlog is only available when Local Information Protocol (LIP) is enabled. 4.16.5.1 Enabling or Disabling Backlog Procedure:

1 From the home screen, press the Menu key. 2 Select Location Backlog Enablement. 3 Select one of the following:

On Activates location report backlog recording. Off Deactivates location report backlog recording. 4.16.5.2 Viewing Backlog Reports Procedure:

1 From the home screen, press the Menu key. 2 Select Location Backlog Reports. The radio displays the number of backlog reports stored. 4.16.5.3 Deleting All Backlog Reports Procedure:

1 From the home screen, press the Menu key. 2 Select Location Backlog Delete All. 4.17 Packet Data NOTICE: This feature is a paid feature. The Packet Data (PD) Service allows you to transfer data in a TETRA system using the Internet Protocol (IP). NOTICE:

To transfer data from a standard computer over the air, connect the computer via the data cable PMKN4129 with your radio. Your service provider has to setup additional applications on your computer. If set up by your service provider it is possible to accelerate the transmission by using the Multi-Slot Packet Data (MSPD) Service. 111 DRAFT MN001488A01-BF (en-US) Main Menu 4.17.1 Viewing Data Statistics Procedure:

1 From the home screen, press the Menu key. 2 Select Packet Data. NOTICE: Data services are only available in TMO Mode. The data option must be set to Voice & Data or Data Only. 3 Select one of the following:

Sent Data the number of KBs sent and throughput since current Packet Data activation is displayed. Received Data the number of KBs received and throughput since current Packet Data activation is displayed. Bandwidth active data session percentage is shown. Failed Transfer the percentage of failed sent/received packets. NOTICE: N.A. standby packet data session. 4.17.2 Viewing Encryption Status Procedure:

1 From the home screen, press the Menu key. 2 Select Packet Data Encryption. 3 The encryption state of the ongoing packet data session is displayed:

Packet Data Channel Clear Packet Data Channel Encrypted Encryption N/A (clear) 4.18 Crypto Menu This sub-menu allows you to manage SIM card based End-to-End Encryption. The End-to-End Encryption is used for:

Encryption of voice transmission in the DMO and TMO Modes. Encryption of messages transmission in the TMO Mode. Encryption of messages transmission in the DMO Mode (the radio cannot be in call). Encryption of position data (GPS) transmission in the TMO and DMO Modes. Transfer of Operational Tactical Address (OPTA) in the TMO and DMO Modes. Management of encryption keys in the TMO Mode. 4.18.1 Enabling or Disabling SIM Card End-to-End Encryption Prerequisites:

112 DRAFT MN001488A01-BF (en-US) Main Menu Ensure that the SIM card is inserted in the radio. The radio is not in an active call. You cannot press the PTT button. See SIM Card End-to-End Encryption on page 127. Procedure:

To enable/disable SIM Card End-to-End Encryption, use one of the following ways:

Press a One-Touch Button ascribed to enabling/disabling SIM Card End-to-End Encryption. From the home screen, press Menu Crypto Menu Crypto Function. Select Encryption On to enable or Encryption Off to disable encryption. Your radio displays prompts indicating your current encryption state: an appropriate status icon and Encryption On or Encryption Off message. 4.18.2 Setting Clear Call Alarm When and where to use: Use this menu item to configure an alarm tone notifying about any clear transmission. Procedure:

1 From the home screen, press the Menu key. 2 Select Crypto Menu Clear Call Alarm. 3 Select Simplex Calls or Duplex Calls. 4 Select one of the following:

Off the alarm is disabled. Single the alarm sounds once at the beginning of a clear call. Continuous the alarm sounds periodically throughout a clear call. 4.18.3 Updating Encryption Keys When and where to use: Use this menu item to update old or incorrect encryption keys. Procedure:

1 From the home screen, press the Menu key. 2 Select Crypto Menu Upd Encr Keys. 3 Select Upd Group Key to start the update. NOTICE:

You can update the encryption keys if the End-to-End Encryption is enabled. The keys cannot be updated when the radio is in a call or in DMO. 113 DRAFT MN001488A01-BF (en-US) Main Menu 4.18.4 Viewing OPTA When and where to use: Use this menu item to view Operational Tactical Address (OPTA) providing supplementary information about a subscriber's organization and operational role. Procedure:

1 From the home screen, press the Menu key. 2 Select Crypto Menu Show OPTA. 4.18.5 Setting OPTA Filter When and where to use: Use this menu item to define which characters are masked when the OPTA name is displayed. Procedure:

1 From the home screen, press the Menu key. 2 Select Crypto Menu OPTA Filter. 3 Highlight check boxes using the Navigation keys and press Select to set which characters are masked when the OPTA name is displayed. 4 Press Done to confirm the changes. 4.18.6 Starting Crypto Registration Prerequisites: Your radio cannot be in an active call nor in DMO. Procedure:

1 From the home screen, press the Menu key. 2 Select Crypto Menu Crypto Registr. 3 Select Start Registr to start the registration. 4.18.7 Configuring Audio Settings When and where to use: Use this menu item to change the audio output for a group call when the call is encrypted but the End-to-End Encryption is disabled. Procedure:

1 From the home screen, press the Menu key. 2 Select Crypto Menu Audio Settings. 3 Select Encr Audio On to enable or Encr Audio Off to mute the encrypted audio for clear mode. 4.18.8 Setting DMO Encryption Mode Procedure:

1 From the home screen, press the Menu key. 114 DRAFT MN001488A01-BF (en-US) Main Menu 2 Select Crypto Menu DMO Encr Mode. 3 Select DMO 1 or DMO 2 to enable the required mode. 4.18.9 Setting Encryption Keys for SDS Messages When and where to use: Use this menu item to set the encryption keys for group and individual SDS messages. Procedure:

1 From the home screen, press the Menu key. 2 Select Crypto Menu SDS Encr Mode. 3 Select Individual SDS or Group SDS. 4 Select Global Key or Group Key. 115 DRAFT MN001488A01-BF (en-US) Features Features 5.1 Ambience Listening (AL) Call Ambience Listening Call allows a dispatcher to make a special call that allows listening to the conversations and background noises within the range of the microphone of a particular radio. The call is set up without any indication to the affected radio, and any lower priority ongoing voice call or packet data transfer may be preempted. After accepting the call, the radio transmits in a simplex call without any action from or indication to the user. The Ambience Listening Call automatically ends when you initiate any voice call, switch to Emergency or TXI Mode, or send Emergency Alarm. 5.2 Bluetooth Bluetooth is a wireless technology used to create personal networks operating in the 2.4 GHz unlicensed band with a range of up to 10 m. The usable range may be reduced when you connect the radio with devices that support more limited ranges or if physical obstacles such as walls appear between devices. There are five separate Bluetooth features available:

Bluetooth Audio - includes Bluetooth Audio and Fast Push-to-Talk (PTT) Bluetooth Connectivity - includes Bluetooth Dial Up Networking (DUN) and Bluetooth Serial Port Profile (SPP) Bluetooth Radio Control - includes Bluetooth Radio Control via AT commands, Bluetooth Generic Attribute Profiles (GATT) Sensors Bluetooth Smart Proximity Pairing Bluetooth Smart Ready - includes Bluetooth Low Energy Indoor Location, Bluetooth Low Energy Heart Rate Profile, and Bluetooth Generic Attribute Profiles (GATT) Sensors You can use Bluetooth to:

Connect the radio with wireless accessories, for example a headset, which gives you a greater freedom of movement and increases your work comfort. Also, wireless accessories allow performing the same activities in several ways. For example, you can change the volume level either in the headset or on the radio. Make your radio discoverable indoors to Bluetooth beacons. Allow radio collaboration with various Bluetooth sensors or data capture devices for example, biometric sensor, bar code scanner, or firearm device. Increase connectivity with secure packet data services between the radio and a Data device or a Smartphone running appropriate applications. Enable radio control through a Data device. The radio supports Bluetooth 2.1 + EDR, Bluetooth 4.0, and Bluetooth Smart (BTLE). Secure Simple Pairing, one of its features, ensures high level of security while pairing devices and thus protects you against recording and passive eavesdropping. One radio can be connected with up to seven devices at the same time. 116 DRAFT MN001488A01-BF (en-US) Features NOTICE: Bluetooth Audio, Bluetooth Connectivity, Bluetooth Radio Control, Bluetooth Smart Proximity Pairing, and Bluetooth Smart Ready are paid features. 5.2.1 Bluetooth Interactions The Bluetooth feature interacts differently with other features and situations of the radio. The following features and situations limit the use of Bluetooth:

Covert Mode The radio cannot enter Discoverable Mode while in the Covert Mode as Covert Mode has a higher priority. Transmit Inhibit Mode (TXI), Repeater Mode Bluetooth does not work in the Transmit Inhibit Mode nor in the Repeater Mode. When the radio enters one of those modes while Bluetooth is enabled, all remote devices are disconnected and Bluetooth is disabled. After leaving the TXI or the Repeater Mode, Bluetooth is enabled again (if it was previously turned on). Wired Audio Accessories Wired audio accessories have a higher priority than Bluetooth audio accessories. If both types of devices are connected to the radio, it disconnects the Bluetooth audio device. When a wired audio device is already connected to the radio, scanning for Bluetooth audio devices is disabled. 5.2.2 Discoverable Mode When the radio is in the Discoverable Mode, it is visible to other Bluetooth-enabled devices. Also, it accepts connection requests from other devices attempting;

or to start a remote control or AT Command session. If enabled, the following item appears in the radio menu: Discoverable (Menu Setup Bluetooth Discoverable). The radio remains discoverable for the amount of time configured. to send files to your radio, to establish a DUN connection, 5.2.3 Add Bluetooth Devices Audio devices, such as headsets or PTT pods are added (and connected) by selecting Add Device from the Bluetooth menu. Sensor devices, such as barcode scanners or firearms devices, and devices used for radio control must be added to the radio codeplug by the service provider before they can be used. Once the radio is configured to use specific sensor devices, they can then be added in the same manner as audio devices, for example; by selecting Add Device from the Bluetooth menu. See Devices on page 74. 5.2.4 Bluetooth Smart Proximity Pairing With the use of Proximity Pairing, you can instantly connect your radio with Bluetooth Low Energy

(BTLE) devices. BTLE devices are various types of sensors the radio can be paired with using Bluetooth, for example gas or heart rate sensors. 117 DRAFT MN001488A01-BF (en-US) Features To pair the radio with a sensor, move the radio close to a sensor and press and hold the One-Touch Button. A tone indicates successful pairing and connection. After the connection, the radio collects information from the sensor. 5.2.5 Bluetooth Sensor Data Your service provider can configure the details of the sensor information the radio displays. Depending on the type of sensor connected to the radio and the setup configured by your service provider, various types of information are displayed. The following sections contain information on the most significant, pre-determined data the radio displays. Sensor Battery Information The radio displays the percentage of the remaining battery power of the connected sensors. Heart Rate Sensor If a heart rate sensor with the Energy Expended feature is paired and connected to the radio, two values are displayed:

Heart Rate in bpm Energy Expended in kJ Sensor Alarm A radio paired with appropriate sensors increases the security of the radio user by making the user more aware of their surroundings. If the collected values exceed limits set by your service provider, the radio plays an alarm tone, light the LED, and display a warning message. The alarm concerns, for example, low battery, high toxicity, or low/high heart rate. The alarm is active for a pre-defined time or until you discard it. 5.3 Buffer Full Overwrite Policy Upon receiving a text message, the radio places the text into a circular buffer. You are notified when a new text message is received and a quick access to read the message is provided. If a delivery report is requested, the radio sends it upon receipt of the message by SDSTL. If a consumed report is requested, the radio sends it when you read the message. NOTICE: If you read the message when the radio is out of service, the report may not be sent. You can save incoming or edited (outgoing) text messages. These messages can be edited and sent. You can also protect the message from being deleted or from the overwriting policy of the radio. For each message, you can verify its timestamp. The timestamp displayed is extracted from the SDS TL PDU. The timestamp is generated and inserted to the message by the SwMI. 5.4 Call-Out NOTICE: This feature is a paid feature. 118 DRAFT MN001488A01-BF (en-US) Features This feature allows you to receive Call-Out alerts. On receiving the Call-Out messages, the radio interrupts current services and attends to the Call-Out alert without any further delay. After the Call-Out is cleared by the dispatcher, the radio exits Call-Out mode and reverts to normal mode. During Call-Out mode, you are only able to receive Emergency calls. However, if your service provider configures Emergency Calls to be ignored during Call-Out mode, the radio rejects them with no notification. If your service provider temporarily blocked the use of PTT in the Call-Out, pressing PTT in the Call-

Out mode is considered an invalid key press until the timer expires. The time-stamp on the Call-Out alert indicates the time and date when the Call-Out is received. To read an entire Call-Out message, scroll down the screen by pressing the Down Navigation key. The length of the message is indicated by the vertical bar on the left of the screen. Figure 8: Call-Out Message NOTICE: Message protection functionality is enabled in the Inbox and Call Out Inbox. Users can only delete unprotected messages. 5.4.1 Types of Call-Out Alerts There are five types of the Call-Out alerts:

Normal Call-Out select Accept, Reject, or Standby. the acknowledgment timer runs out. An alert message that is sent by a dispatcher either to a single radio or to a group of radios. There two types of Normal Call-Out:

With user receipt The radio gets to the Accepted phase when you:

Without user receipt The radio gets to the Accepted phase when you:

press Menu or any key except for the Emergency button, or the Rotary Knob. The Normal Call-Out mode is ended when the validity timer runs out. the acknowledgment timer runs out. Storm Plan An alert message that is sent by a dispatcher to a group of radios. To raise its reliability, it is sent several times. You are not able to respond to the Call-Out alert and any key press takes you to the information phase. Simple Call-Out An alert with the functionality similar to full Call-Out but without the information phase. There two types of Simple Call-Out:

119 Call-Out 137Severity-2SC TG1AcceptRejectDRAFT MN001488A01-BF (en-US) Features With user receipt The Call-Out mode is ended when the acknowledgment timer runs out, or when you select Accept, Reject, Standby, or reply with a text message. Without user receipt The Call-Out mode is ended when the acknowledgment timer runs out, or when you press any key, except for the Emergency button, or the rotary knob. Fallback Mode An alert message that is limited only to voice communication. To initiate this type of Call-Out, press a One-Touch key predefined by your service provider. It can be cleared manually. NOTICE: Fallback is only possible when the radio is in Local Site Trunking. Test Call-Out a special Call-Out alert that is sent by the dispatcher to test this feature. On receiving the Test Call-

Out, the radio plays a tone and displays Test Call-Out. To respond and clear the alert, press the Test OK Soft key. 5.4.2 Call-Out Modes Interaction Call-Out feature operation is different in other modes:

TXI Mode you can read the message but you cannot respond to it. You have an option to leave the TXI Mode by pressing soft key or reject the Call-Out message. TMO Call-Out is supported. DMO Mode Call-Out is not supported. Emergency Mode all Call-out alerts are ignored. 5.4.3 Call-Out Service Phases In the Call-Out mode there are following phases:

Alerting phase the radio receives a Call-Out message. An alarm tone indicates the message. When the text is displayed, you have the following options:

- Accept,

- Reject, or

- Menu. NOTICE: If your service provider allowed it, you can stop the alert tone by pressing any key. Information phase you are still in the Call-Out mode and you can receive more detailed information about the incident that occurred through subsequent text or a voice message. You can query for more information using voice group call or Call-Out text function which enables you to send a text message. You are able to respond to a Call-Out by using a pre-coded message selected from a list of predefined replies. 120 DRAFT MN001488A01-BF (en-US) Features 5.5 Collaborative Messaging This feature allows external device to send/receive message when the radio application is enabled. It is mutually exclusive with Secure SDS Storage feature and EtE High Security Mode Feature. The external device can be connected to the radio using either Bluetooth connection or wired cable connection. It includes the following functions:

Inbox/Outbox synchronization. Notification on message status, or user action synchronization between the external device and the radio. NOTICE: This feature does not support Call Out/RMS/Home Display. 5.6 Dialing through Soft Numeric Keypad Prerequisites: Direct Private Number Dialing is assigned to a Right Navigation key. Procedure:

1 From the home screen, press and hold Right Navigation. Your radio displays dialing number prompt. 2 Press Up or Down Navigation key to choose the number, then press Right Navigation key to go to the next digit. NOTICE:

You can enter # at the end when the Speed Dialing feature is enabled. The + sign you can enter only when you are editing the first position. Both signs are available after digit 9. 3 Press the PTT or the Send key (only in TMO). 5.7 Global Navigation Satellite System (GNSS) Location Service NOTICE: This feature is a paid feature. The Global Navigation Satellite System (GNSS) Location Service feature uses information from GNSS satellites orbiting the Earth to determine the approximate geographical location of your radio. The GNSS Location Service availability, accuracy, and the position calculation time vary depending on the environment in which you use the radio. The GNSS Location Service can assist your dispatcher or colleagues in many ways such as more efficient deployment of resources or locating your radio when you trigger your emergency service. The radio can display the location information directly on the screen or send it over the air to your dispatcher to display it in the control center. Check your radio configuration details with your service provider. The radio supports the following system combinations:

GPS GLONASS 121 DRAFT MN001488A01-BF (en-US) Features BeiDou GPS + GLONASS GPS + BeiDou IMPORTANT:

Where the signals from satellites are not available, the GNSS Location Service does not work. This situation usually happens when your radio cannot establish a view of a wide area of open sky, for example, when the GNSS antenna is covered or facing the ground. Such situations include being:

Under any other metal or concrete roof or structure Near a powerful radio or television tower In underground locations Inside buildings, trains, or other covered vehicles In extreme temperature outside the operating limits of your radio Even if your location information can be calculated in such situations, it may take longer to do so. Therefore, in any emergency situation, always report your location to your dispatcher. Where adequate signals from multiple satellites are available, your GNSS Location Service feature provides a location, most probably near to your actual location. The radio can be triggered to send Location Reports in various circumstances, for example:

Upon a request Entering Emergency Mode At specified time intervals At specified distance intervals The Location Reports can be sent both in TMO and DMO by using:

SDS messages Packet Data (in TMO mode only, with Packet Data enabled on the network by the service provider) The radio can be configured to give audio-visual notifications upon sending the Location Reports. Depending on the radio settings, viewing the radio position and the status of the visible satellites is available. The position may consist of longitude and latitude, UK, or Irish grid coordinates. 5.7.1 Enhance GNSS Performance Sometimes the GNSS feature is unable to complete a location calculation successfully. You hear an audible tone indicating that your radio cannot see the satellites. To maximize the ability of your radio to determine a location fix please note the following guidelines:

Stay in the open The GNSS feature works best where there is nothing between your radio and a large amount of open sky. If possible, go outside, away from tall buildings and foliage. While the performance in a building is improved by moving closer to windows, glass with certain sun shielding films may block satellite signals. Position your radio to enhance reception Signals from GNSS satellites are transmitted to your GNSS antenna, which is in your radio antenna. Hold your radio away from your body, giving the antenna clear access to satellite signals. Do not cover the antenna area with your fingers or anything else. Stand still If possible, stand still until your radio is finished determining your location. Moving your radio at a walking pace while your radio is calculating your approximate location may substantially decrease GNSS performance. 122 DRAFT MN001488A01-BF (en-US) Features This feature works best where there is nothing between your radio and a large amount of open sky. To maximize the ability of your radio to determine a location fix, avoid closed space, tall buildings, and foliage. If possible, do not use this feature in underground parking lots, tunnels, under bridges, and close to high buildings. 5.7.2 Location Report Backlog The radio can record location track when it is out of service, when in DMO, or when in TXI mode. The location reports generated during this time is stored, and all location report backlog recordings are uploaded once the radio is back in service. Your radio can save up to maximum 180 location reports. The location report backlog function differently when in different mode:

Location Backlog Recording in Trunked Mode Operation (TMO) The radio starts recording location reports when radio is out of service in TMO Mode. The radio resumes latest location reporting when TMO coverage is regained. Location Backlog Recording in Direct Mode Operation (DMO) The radio starts recording location reports in DMO Mode. The radio resumes latest location reporting when it switches back to TMO mode. NOTICE: This feature is only available when enabled by your service provider. Location Backlog Recording in Transmit Inhibit Mode (TXI) When the radio is in TXI mode, location reports are generated and recorded but not sent out. Once the radio exits TXI mode and is within TMO coverage, the location reports are uploaded to the server. 5.7.3 GNSS Icon When GNSS is enabled, the following icon is displayed in the status icon area:

Depending on the current GNSS state, the icon can be solid GNSS has a fix, or blinking GNSS is searching for a fix. The blinking GNSS icon can be disabled/enabled by your service provider. 5.7.4 Different Location Displays Table 17: Different Location Displays Latitude/Longitude Time Latitude Longitude Altitude Satellites UK Coordinates Time 2-Letter Code Easting and Northing Coordi-

nate Altitude Satellites Irish Coordinates Time 1-Letter Code Easting and Northing Coordi-

nate Altitude Satellites Time indicates when the last time the location was calculated. The time is provided in Universal Time Coordinated. 123 DRAFT MN001488A01-BF (en-US) Features Letter Code grid zone or square on the map for different coordinate standard. Latitude expressed in degrees, minutes, and seconds. Longitude expressed in degrees, minutes, and seconds. Number of satellites used to calculate the location. In general, more satellites provides better accuracy. The maximum is 12 satellites. Easting refers to the eastward-measured distance expressed in meters. Northing refers to the northward-measured distance expressed in meters. NOTICE: Skipping each digit of easting and northing coordinates decreases the accuracy by the factor of 10. 5.7.5 GNSS Accuracy The GNSS Location Service accuracy depends on the GNSS coverage and the selected accuracy mode. In good GNSS coverage (at least -137 dBm or in open sky), the location accuracy presents as follows:

In high accuracy mode, the accuracy is:

- 5 m for 50% of location reports.

- 10 m for 95% of location reports. In power optimized or normal mode, the accuracy is:

- 20 m for 50% of location reports.

- 50 m for 95% of location reports. NOTICE:

The presented values depend on variety of factors, for example the view on the sky. To optimize the GNSS performance the radio should have the clearest possible view of the open sky. The use of the high capacity battery is recommended, especially when high accuracy mode is used. 5.8 Home Display Text Message Your radio is provided with a feature that allows your service provider to send special text messages to the display. The message stays on the home screen until a new message is received. Power cycle your radio to replace the Home Display message to the predefined one. 5.9 MS-ISDN This feature adds to the radio ISDN number. You can choose between MS-ISDN and ISSI to address the call, send the message or pre-defined templates. It works for both simplex and duplex calls, based on the assigned ISDN number. 5.10 Private Call Private Call, also called Point-to-Point, or individual call, enables calling between two individuals. No other radio can hear the conversation. This call type can be carried out in two ways:

124 DRAFT MN001488A01-BF (en-US) Features Duplex call (if the system allows), in TMO Mode. Both parties can speak at the same time. Start the conversation using the Send key. Simplex call, in TMO or DMO Mode. Only one party can speak at a time. Start the conversation using the PTT button. When a DMO Private Call takes place, radios not involved in this call receive the channel busy indication. The radios are identified using its radio numbers. 5.10.1 Making Private Calls Prerequisites:

Direct Private Number Dialing is assigned to the Right Navigation key. Procedure:

1 From the home screen, press and hold the Right Navigation key and enter a number. 2 If Private is not the first type of call presented, press Ctype repeatedly to select it. 3 When you are in the following mode:

TMO For simplex calls, press and release the PTT button. You hear a ringing tone. Otherwise, press and hold the PTT button. Wait for the talk permit tone before talking, and release the PTT button to listen. For duplex calls, press and release the Send key. You hear a ringing tone. DMO Only simplex calls are available. Press and hold the PTT button. Wait for the talk permit tone before talking, and release the PTT button to listen. 4 To end the call, press the End key. 5.11 Phone and Private Automatic Branch Exchange (PABX) Calls Phone Call allows you to call a landline telephone number or a cellular mobile phone number. Private Automatic Branch Exchange (PABX) Call allows you to call local (office) extension numbers. 5.11.1 Making Phone or PABX Calls NOTICE: This feature is only available in the TMO mode. Prerequisites: Direct Private Number Dialing is assigned to the Right Navigation key. Procedure:

1 From the home screen, press and hold Right Navigation key and enter the number. 2 If Phone or PABX is not the first type of call presented, press Ctype repeatedly to select it. 3 Press Send key. 5.12 Phone/PABX Speed Dial This feature allows you to dial Phone/PABX by a shortened number of up to three digits instead of the full number. The Phone/PABX Speed # number is assigned when the dialed number is added in the contact list. 125 DRAFT MN001488A01-BF (en-US) Features NOTICE: This feature is available only in TMO Mode. 5.12.1 Using the Phone/PABX Speed Dial Procedure:

1 From the home screen, enter the predefined Phone/PABX speed dial number and # key. 2 Press Send key. 5.13 Radio Messaging System (RMS) NOTICE: This feature is a paid feature. The Radio Messaging System (RMS) feature allows the radio to receive and send RMS messages through the TETRA network using the Short Data Service (SDS-TL) or Status (STS) as the transport layer. NOTICE: One-Touch Buttons are disabled in the RMS mode. There are two types of RMS messages:

RMS Status a predefined code that is sent bidirectionally between the radio and the service provider. The radio can have up to one hundred statuses that are assigned to numeric keys from 0 to 9. A received RMS status is displayed on the home screen. RMS Free Text (available in SDS-TL only) a unidirectional message containing free text that is sent to the radio by the service provider. Since this type of message may be longer, the radio displays only its beginning on the home screen. To view the full message, go to Menu Messages RMS Box. The latest RMS free text or the latest received or sent RMS status is kept on the home screen until the next power cycle. RMS free text messages and incoming and outgoing RMS statuses are stored in the RMS Box. Its capacity is maximum one hundred entries for incoming and outgoing RMS messages. If the RMS Box is full, any new incoming or outgoing RMS message overwrites the oldest message (received or sent). The latest RMS free text is kept on the home screen until the next power cycle. The latest received or sent RMS status is kept on the home screen until the next power cycle or up to 30 seconds (depending on the settings configured by your service provider). The radio receives and sends RMS messages only from and to the numbers predefined by your service provider. See Sending an RMS Status on page 67 on how to send an RMS message. 5.13.1 RMS Icons Table 18: RMS Icons Icon 126 Description RMS Status Received DRAFT MN001488A01-BF (en-US) Features Icon Description Indicates a new RMS status message just arrived. RMS Status Sent RMS Box Read Message RMS Box Unread Message 5.14 Radio User Assignment (RUA) and Radio User Identity (RUI) NOTICE: This feature is a paid feature. Radio User Assignment (RUA) and Radio User Identity (RUI) enables authentication service. Only a successful logon to any temporary radio, provides full access and your permanent radio functionality, so you can be still reached with your permanent number. A logon failure results in limited service. You can differentiate the RUA/RUI state by the interface color:

Blue you are logged on Gray you are logged off Radio States Full Service user logon was successful. Your radio has full functionality. Limited Service user not logged on. Specified by the service provider. Pseudo Log On occurs only in the Local Site Trunking (LST). You radio has full functionality available (depending on the service provider settings) except some services like forwarding calls. The RUI Pseudo Log On icon is displayed. Book On Your service provider assigns particular radio to one person for a predefined period of time. You are only going to see the screen with your login and the full service is granted. Force Off Your service provider can log you off. Radio displays Force Off. 5.15 SIM Card End-to-End Encryption The table below presents interactions occurring between radios with and without SIM card. SIM card provides End-to-End Encryption. 127 DRAFT MN001488A01-BF (en-US) Features NOTICE: This is a BSI feature only. Table 19: Radios Interactions Transmission Type Private Call Transmitting Ra-

dio SIM card Receiving Radio Result No SIM card Private Call No SIM card SIM card Group Call SIM card No SIM card Group Call No SIM card SIM card Message SIM card No SIM card Message No SIM card SIM card Call is not visible for the re-

ceiving radio. The transmit-

ting radio displays Called Party Clear Only mes-

sage. Warning: clear call message appears and the call is received. Call is not visible for the re-

ceiving radio. Warning: clear call message appears and the call is received. Delivery failed notifica-

tion appears and the mes-

sage is not received. Message is received. NOTICE: To send a message or call a non-SIM card radio, turn off the SIM card End-to-End Encryption. 5.16 Short Number Dial This feature allows you to dial part of the full number of the person you wish to call. Your radio automatically completes the number. Example: Your radio number is 4282564. 1 Dial 564 (instead of 4282564, the full number). 2 To place the call, press the PTT button or the Send key. 5.17 Talkgroup Dialing by Index This feature allows you to attach to any talkgroup by dialing its index, instead of choosing it from the talkgroup folders and lists. NOTICE: It is also known as Talkgroup Speed Dial. 128 DRAFT MN001488A01-BF (en-US) Features 5.18 Terminal Permanent Disable NOTICE: This feature is a paid feature. Your radio is provided with a feature that allows your service provider to disable it permanently in case it is stolen or lost. When your radio is disabled permanently, it becomes inoperable. After a Permanent Disable your service provider cannot enable your radio. It is recommended to Permanent Disable your radio only when you do not expect to recover it. If it is recovered then a Permanent Disable radio can be reactivated by returning it to Motorola Solutions. 5.19 Terminal Temporary Disable or Enable Your radio is provided with a feature that allows your service provider to disable it temporarily in case it is stolen. When your radio is disabled or is powered up in disabled state, it looks and acts like it is turned off. If your radio is found, your service provider can enable it again over the air. After your radio is enabled, you may resume normal operation. 5.20 Writing Text Every time that you see text entry screen, refer to this section. Use the Up/Down Navigation key to enter text, and the Right/Left Navigation key to go to the next/

previous character. To change the text entry mode, long press the Left Navigation key. To insert a new character into an existing word, long press the Right Navigation key. 5.20.1 Text Entry Icons In the text entry screen, icons tell you which text entry mode and method you are using. A character counter displayed on the text entry icon, indicates the amount of characters that can be entered. Press and hold the Left Navigation key to toggle through the text entry modes. Table 20: Text Entry Screen Icons Icons Description A-Z all capitals a-z no capitals Enter numbers and symbols: 0-9 # ^ ~ \ } { ] [ $ > < = * % & + ; _ : / ) ( -

@ ! ? , . 129 DRAFT MN001488A01-BF (en-US) Features 5.20.2 Keys Usage Table 21: Keys Usage Key Send Delete Up Navigation key Down Navigation key Right Navigation key Left Navigation key Menu Description Press to send the message. You have a choice to send it to a Private user or a Group. The target can be entered manually or selected from the Contacts List. Press once to delete the highlighted character. Press and hold to clear the entire main text area. Press to scroll through the letters, or numbers or symbols. Press to scroll through the letters, or numbers or symbols. Press to navigate to the right. Press to add a new character at the end of text (a, A or 0). Long press to insert a new character into an existing word. Press to navigate to the left. Press to add a new character at the beginning of text. Long press to select the text entry mode. Opens the Editor Menu to store the message as a template or save changes. 5.21 Wireless Application Protocol (WAP) NOTICE: This feature is a paid feature. Wireless Application Protocol (WAP) is a standard for application layer network communications in a wireless communication environment such as TETRA network. The protocol is used to access the mobile web from a radio through a WAP browser. 5.21.1 WAP Browser The Openwave Mobile Browser is a Wireless Application Protocol (WAP)-compliant user agent. The WAP browser, available only in TMO mode and on a network with Packet Data enabled, provides all the basic services of a computer web browser. Depending on the CPS configuration, the display can return to the browser session automatically after an interruption by the preemptive display. The WAP browser does not support right-to-left languages (as Arabic and Hebrew); English is used instead. The characters of right-to-left scripts are not displayed. NOTICE: Depending on the radio configuration and the network conditions, the WAP browser may not display images properly (or may display them with a delay). 130 DRAFT MN001488A01-BF (en-US) Features 5.21.2 Entering the Browser Prerequisites: From the home screen, press the Menu key. Set Setup Data Setup to Data Only or Voice & Data. Procedure:

1 From the home screen, press the Menu key. 2 Select Browser. 3 Optional: Exit the browser by pressing and holding the END key. 5.21.3 Entering Browser Menu Panes Prerequisites: You are in the browser. Procedure:

1 Press Menu or Menu key. 2 Usually, it brings up the Navigate pane, or the last browser menu pane. NOTICE: If the web page you navigated to has two or more soft keys/options, the Options pane pops up. From here, you may scroll to other panes with the Left or Right navigation keys Or you may select Browser Menu and then scroll to the required pane. 5.21.4 Tips for Browsing Create and use the following steps for easy browsing. 5.21.4.1 Creating Bookmarks through the Navigate Pane Procedure:

1 Enter the browser and browse to the required page. 2 Press Menu to enter the browser menu. 3 Select Mark Page. 4 The screen displays the title and URL of the marked page. 5 To save it:

a Press Save (or Select) to save the page in bookmarks. b Select Menu and select an option:

Save Confirms the bookmark creation. Edit Allows you to edit the title, folder, choice, and URL of the created bookmark. 5.21.4.2 Creating Bookmarks through the Bookmarks Pane Procedure:

1 Enter the browser. 2 Scroll to Bookmarks pane. 131 DRAFT MN001488A01-BF (en-US) Features 3 Select Organise (if there are no saved bookmarks), or More... 4 Select Menu. 5 Scroll to New Bookmark. 6 Enter the bookmark title and URL, and select its location. 7 Press Save. 5.21.4.3 Using Bookmarks Procedure:

1 Enter the browser. 2 Scroll to Bookmarks pane. 3 Scroll to the required bookmark and select Go. The bookmark downloads the selected page from the web. 5.21.4.4 Saving Pages When and where to use: Save a page for off-line browsing. Procedure:

1 Enter the browser and browse to the required page. 2 Press Menu. 3 Scroll to Tools pane. 4 Select Save Page. Edit the proposed page title if required. Scroll down and select Save. The page will be saved in the Bookmarks Saved Pages folder. 5.21.4.5 Selecting Saved Pages Procedure:

1 Enter the browser. 2 Scroll to Bookmarks pane. 3 Select Organise (if there are no saved bookmarks), or More... 4 Select Go to enter the Saved Pages folder. 5 Select a saved page and press OK. The display shows the saved page. Depending on the saved page, you may browse the web from here. 5.21.5 Disabled Packet Data Service If there is no Packet Data Service, your radio displays Error: No Network Available when entering the browser for the first time. Select Left Soft key to retry entering, or Right Soft key to enter the browser menu. When re-entering the browser with previously available Packet Data, the radio displays the last browsed page, or the last page to which you navigated off-line. 132 DRAFT MN001488A01-BF (en-US) Features 5.21.6 Disabled Browser Entry Browser entry is disabled:

During any type of voice call, except Ambience Listening Call. During Emergency Mode. During PIN lock. Service provider has not configured this feature. When the radio is disabled. In DMO Mode. NOTICE:

Browser entry is enabled during Ambience Listening (AL) Call. If you navigate to previously stored pages, the AL state remains. When you activate Packet Data for the first time, AL is disconnected, and you have the same look and feel as if you were not in AL before. 5.21.7 Browser Keys Usage When the browser is active, the following usage described occurs inside or outside the editor. Table 22: Browser Keys Interactions Key Press Left or Right Soft key Up Navigation key Up Navigation key (hold) Down Navigation key Down Navigation key (hold) Left Navigation key Left Navigation key (hold) Right Navigation key Right Navigation key (hold) Center of Navigation keys (hold) Menu key End key Send key Rotary Knob Action Selects the option that appears in the display di-

rectly above the left and right soft key (part of the page). While in list of options, moves up one line. Moves up on page. While in list of options, moves down one line. Moves down on page. Moves to the previous pane. In the editor: moves left. Functions as backward. Moves to the next pane. In the editor: moves cursor to the right and inserts space if at the end of the word. Functions as forward. Auto-repeat. Brings up the browser menu. Press to deactivate the browser. Disabled in browser active state. Used for volume adjustment only. 133 DRAFT MN001488A01-BF (en-US) Features Key Press Emergency button 5.21.8 Browser Menu Panes Overview The browser menu includes the following panes:

Action Deactivates the browser. The radio enters Emergency Mode. History Tools Image Input Text Table 23: Browser Menu Panes Menu Pane Navigate Bookmarks Description Provides access to the home page and commonly used items. Provides access, editing, and storage options to stored bookmarks and saved pages. Provides access to recently visited pages and shows the position of the currently loaded page in the history stack. Provides access to applications and utilities. The following panes are displayed according to the context:

Table 24: Additional Menu Panes Menu Pane Options Description Displayed only when there are additional options for the pane or page. Displayed only when an image is selected. Provides access to im-

age details, storage, and display use. Displayed only in text entry mode. Provides access to text entry mode (for example, symbol). 5.21.9 Navigate Pane You can select one of the following items:

Home for loading the home page. Open Page for entering the URL. Search item disabled. Mark Page for creating (saving) a bookmark for the current document. A title and URL for the bookmark are displayed, and the root folder is chosen for the location. Forward for navigating to the document located one step forward in the navigation history. If there is no forward history, this item is disabled. Reload for reloading the current document. Advanced... see following section. 134 DRAFT MN001488A01-BF (en-US) Features 5.21.10 Advanced... From the Navigation pane select Advanced... to see the following options:

Settings...

- Downloads for setting download preferences. You may deactivate the downloading of images and objects. The browser displays a special icon instead of the images and objects.

- Scroll Mode for setting the scrolling mode and speed.

- Key Press Timeout for setting key press time-out. This time-out is used for text entry.

- Set Proxy select the WAP Proxy (1, 2, 3). The browser connects to the web via the selected proxy or gateway. The network provider installs and configures the proxy. To establish a secure session, select a secure proxy. Please ask your service provider which proxy is configured for a secure session. Though you can choose your home page, the service provider may decide to force its own home page on your terminal.

- Circuit Prompt for turning on/off the circuit prompt.

- Resend Data Prompt for turning on/off the data re-send prompt. Security...

- Secure Prompt for enabling/disabling the browser to inform you that it replaced a non-secure connection with a secure connection, and the other way around.

- Current Certificate for viewing the digital certificate identifying the server that delivers the current document. A Certificate Authority (CA) digitally signs and thus authenticates this certificate. Up to ten additional custom WTLS certificates can be added to the default list of certificates installed. Please ask your service provider if you wish to have these custom WTLS certificates added.

- CA Certificates for viewing the digital certificates installed in the browser and digitally signed by Certificate Authorities (CA).

- Send Referrer for turning ON/OFF sending of the HTTP Referrer header as part of HTTP requests. The Referrer header provides the URL of the link source to the server.

- Authentication for turning ON/OFF the caching of HTTP Authentication credentials. HTTP Authentication protects access to content on the server. If you try to access a protected content, you enter your credentials (user name or password). Clear... for clearing of browser data: history, cache cookies, or auto-fill. Restart Browser for restarting the browser. About... for showing the information about the current version of Openwave Mobile Browser. 5.21.11 Bookmarks Pane If there are bookmarks in the root folder, select More... to access the Options pane. If the root folder is empty, select Organise... then press Menu key to access the Options pane. The Options pane allows you to manage bookmarks. The Saved Pages folder contains snapshots of saved pages. 5.21.11.1 Working with the Options Pane for Selected Bookmarks Procedure:

1 From the Bookmarks pane select More... 2 Scroll to a bookmark. 135 DRAFT MN001488A01-BF (en-US) Features 3 Press Menu to open the Options pane for that bookmark. 4 Select one of the following:

Back for displaying the page associated with the bookmark (page is downloaded if not available in cache). Details for modifying the bookmark title and URL. Delete for deleting the bookmark. New Bookmark for creating a new bookmark. New Folder for creating a new folder. Move for moving this bookmark to a new folder (or in Bookmarks). Delete All for deleting all bookmarks. Hotkeys for assigning hotkeys to available bookmarks. 5.21.11.2 Working with the Saved Pages Folder Procedure:

1 From the Bookmarks pane select Saved Pages folder. 2 The browser displays the page (snapshot) saved using Save Page in Tools pane. 3 Scroll to a saved page. 4 Press Menu to open the Options pane for the saved page. 5 Select one of the following:

Back for displaying this page saved on its cache. Details for modifying the page title and URL of the saved page. Update Page for replacing the saved version with the current version (to be downloaded from server). Delete for deleting this page from its cache. Delete All for deleting all the saved pages from its cache. Cancel for exiting this pane and returning to the last page displayed. 5.21.12 History Pane This pane displays the list of recently visited pages (up to nine history entries can be listed). Each history entry shows its title, if present. Otherwise, No Title is displayed. 5.21.12.1 Navigating to Recently Visited URLs Procedure:

1 Select the URL. 2 Press OK. 136 DRAFT MN001488A01-BF (en-US) Features 5.21.13 Tools Pane Procedure:

1 From the Tools pane select More... 2 Scroll to a document. 3 Select Menu key to open the Options pane for that document. 4 Select one of the following:

Show URL For displaying the current page URL. Save Page For creating a snapshot for the current document. Find Text For finding a text string in the current document. Copy Text For copying text from the current document to the clipboard. 5.21.14 Options Pane This pane is specific to the page or pane being displayed. 5.21.15 Text Input Pane Prerequisites: This pane is visible when the browser menu is opened and text entry field is active. When and where to use: To input the text for the URL. Procedure:

1 Select the URL. 2 Press abc. The text input pane opens up. 3 Select www. 4 Scroll the required extension (for example: .com). 5 Press .com. The screen displays the URL with the selected extension. Soft Key abc Table 25: Browser Text Input Icons Mode Alphabetic characters - low-

er case Alphabetic characters - up-

per case Numeric http mode ABC 123 www Action Enter text in lowercase. Enter text in uppercase. Enter numbers and symbols. Enter. 137 DRAFT MN001488A01-BF (en-US) Features 5.21.16 WAP Push NOTICE: This feature is a paid feature. Wireless Application Protocol (WAP) Push allows WAP content to be pushed to a radio. This push is carried out by sending a specially formatted (Push Access Protocol) XML document to the Push Proxy Gateway, that in turn forwards the document to the radio. A WAP push message is an encoded message including a link to a WAP address. When receiving a WAP push, a WAP enabled radio automatically gives the option to access the WAP content. The implemented WAP push is compliant with WAP 2.0 standard. The radio supports WAP 2.0 through a proxy only. Proxyless connections are not supported. 5.21.16.1 New WAP Messages Types of the WAP Messages and their priorities:

NOTICE: Your service provider sets the priority of the message. Push Message

- High animation and the icon (blinking) are displayed with the New WAP Message tone and the browser opens.

- Medium animation and the icon are displayed with the New WAP Message tone.

- Low icon is displayed with the New WAP Message tone.

- Delete available only if you are in WAP Box, the text WAP Message deleted remotely is displayed, otherwise there is no indication. NOTICE: Animation is not displayed if you are in a call, or in Emergency Mode, or in Call Out, or in message editor, or PIN lock state, or switching to DMO. Load Push Message

- High browser opens to the user with the New WAP Message tone.

- Low the icon is displayed with the New WAP Message tone. NOTICE: The browser does not open if you are in a call, in Emergency Mode, in Call Out, in message editor, in PIN lock state, or when switching to DMO. 5.21.16.2 Viewing WAP Messages Procedure:

1 From the home screen, press the Menu key. 2 Select Messages WAP Box. 3 Select the required message. 4 Select Go to to view the message in the browser. 138 DRAFT MN001488A01-BF (en-US) Tones Appendix A Tones NOTICE: The radio has two tone packs which are the default Classic Tones and New Tones. Your service provider decides which tone pack is enabled. To listen to the audio signal tones samples, click

. Table 26: Radio Tones New Tone Classic Tone Tone Description Default Beep Played when pressing a key. Invalid Action Examples:

Pressing an invalid key. Dialing an invalid number. Talk prohibit. System Notification Examples:

The radio changes its status from out-of-range to in service. The radio returns to the home network. Toggling between TMO and DMO modes. System Error Examples:

The radio changes its status from in service to out-of-range. Call disconnected. General Notification Examples:

Entering Local Site Trunking. Entering Transmit Inhibit Mode. Positive Notification Message sending succeeded. Negative Notification Message sending failed. Item Received A new message received. Talk Permit The radio user is allowed to transmit after pressing the PTT button. Clear-to-send Data transmission is ready to begin. Emergency Emergency Call received. 139 DRAFT MN001488A01-BF (en-US) Appendix A: Tones New Tone Classic Tone Tone Description Emergency 2 Emergency Call received (optional tone). Low Battery Battery charge level is low. Over the Air 1 Single D-PTT tone. Over the Air 2 Double D-PTT tone. Over the Air 3 Triple D-PTT tone. Phone Busy The called radio is busy. Phone Ring Back Played on the initiating phone when Phone Call is being set up. Private Ring Back Played on the initiating phone when Private Call is being set up. Ringtone 1 Ringtone 2 Ringtone 3 Ringtone 4 Ringtone 5 Simplex Volume Set Played when adjusting simplex volume. Duplex Volume Set Played when adjusting duplex volume. 140 DRAFT MN001488A01-BF (en-US) LED Indications Appendix B LED Indications Table 27: LED Status Indications Indication Solid green Status In use Repeating call Blinking green Solid red Blinking red Solid orange Blinking orange No indication In service or idle Switching modes from TMO to DMO Out of service Connecting to the network Switching modes from DMO to TMO Radio is powering up Transmit inhibit in service Channel busy in DMO Radio interference in DMO Incoming call Radio powered down Radio in Covert Mode Table 28: Battery Charging LED Indications Indication Solid green Blinking green Solid red Blinking red Blinking orange Status Battery fully charged Battery charged at 90%

Rapid or trickle charge Faulty or invalid battery Battery is waiting to charge NOTICE:

When you charge your radio in a multi-unit charger and the battery is at the 90100% charge level, the LED indicators on the radio and on the multi-unit charger differs:

LED on the radio blinking green. LED on the multi-unit charger solid green. If you insert a radio with a deeply discharged battery into the multi-unit charger, the LED on the radio shows blinking red, indicating a charging error. Resolve this error by reinserting the radio. 141 DRAFT MN001488A01-BF (en-US) Appendix C: Troubleshooting Appendix C Troubleshooting Your radio displays the following messages:

Table 29: Displayed Messages Message

...-Received Attachment Failed Authenticate Failure Battery level too low Call Cancelled Call Ended Call Forwarding Call Modified Call Preempted Decryption Failed:

Emergency In Use Wait For Mic Emgcy Mic Ended Emergency Mic On Empty Entry Faulty Unit Error Gateway available 142 Message Description Call received but not answered, or rejected. Your radio could not perform talkgroup attachment. It keeps on trying. If it does not succeed, try another talk-

group. Your radio could not register on an authenticated system

(for example, the Authentication Key is incorrect, or au-

thentication is disabled). The battery charge level is too low to perform the required operation. You have canceled the call. Faulty channel. Please try later. You have ended the call. The radio you are trying to call is not available and the call is being forwarded to another radio. The call you are participating in has been modified. Channel being used for priority. An error occurred while decrypting a message or call. The Hot Microphone feature is active, but the channel transmit grant has been given to another Emergency call on the same talkgroup. Your radio microphone is not ac-

tive during this time, but it automatically tries to regain talk permit after a predetermined time. The Hot Microphone timer automatically expired, or you pressed the PTT button to cancel the Hot Microphone fea-

ture. The Hot Microphone feature is active, and your radio is au-

tomatically transmitting hands free emergency audio. The speed number you dialed does not exist, or the num-

ber exists but the group is non-selectable. Self-test failed. An operational fault has been detected with your radio. Record the error number. Turn your radio off and contact service. Your radio has connected to a gateway. DRAFT Message Gateway not available This group already exists Individual Calls Only Insufficient visible data Insufficient visible satel-

lites Invalid ID Limited Service List Empty List Not Attached List Partially Attached Message Delivered Message Failed New Delivery Status No Service Not allowed in repeater mode My Groups Is Empty My Groups Is Full Network Trouble No Answer No Entries No Group MN001488A01-BF (en-US) Appendix C: Troubleshooting Message Description Your radio cannot connect to a gateway, or connection has been lost. The group you are attempting to add exists in the My Groups folder. You can make only individual (private) calls. Your radio is in the process of determining your location. This process may take several minutes to complete. Your radio is in the process of determining your location. This process may take several minutes to complete. The entered number is not valid. Emergency Calls, Emergency Alarms, and mobility opera-

tions (for example, group attachment) are allowed. All oth-

er incoming and outgoing call and data services are blocked. There are no programmed entries in the scrolling list. Type the entry. All talkgroups in the scan list are not attached. The scan list is active, but not all talkgroups are attached to it. Indicates mail successfully delivered. Indicates mail delivery failure. You have received a new Delivery Status. Your radio is outside coverage. Return to coverage. The service or feature is not available in the Repeater Mode.. You cannot view/delete groups when the My Groups fold-

er is empty. You are not allowed to add a group to the My Groups fold-

er as it already contains the maximum allowed number of groups. Network problems. Please try again later. The called party does not answer. This message is displayed when accessing an empty list. Attachment failed. Your radio detached from current talkgroup. Please wait until it attaches again to the cur-

rent talkgroup. Displayed when you are out of the normal coverage area of your selected talkgroup. Please select a new talkgroup that is valid for your working location. Indicates a favorite group was removed from the My Groups folder. 143 DRAFT Message Description The network list is empty. Indicates there are no new or old messages in the Inbox. You selected an empty network list. Your radio is out of coverage. You are not allowed to dial a number which is not in the address book. Release the PTT button and try again later. You are not al-

lowed to send a text message or a status message to a number which is not in the address book. There is only one programmed entry in the scrolling list. Your radio turns off. Keep it turned off for 5 minutes. Called radio is busy. Called radio is out-of-range or turned off. Please try again later. You could not call. A message during startup. Your radio could not register within the system. Please try again later. Your radio has connected to a repeater. Your radio cannot connect to a repeater, or connection has been lost. Invalid number. Call your service provider. This service is not available on the current network. This service or feature is restricted by your service provid-

er, it has not been purchased, or it is not available. Your service provider set this group so you cannot delete it from the favorite talkgroup folder. The requested service is temporarily unavailable. Check with your service provider. Self-test error. A minor fault has been detected. Your radio is still fully operative. If this error recur, note the error code and contact service. Your radio could not attach to the system. The talkgroup may not be defined in the system. Please try another group. MN001488A01-BF (en-US) Appendix C: Troubleshooting Message No List No New or Old Messages No Selected Scan List No Service Not Allowed To Initiate Call Not Allowed To Transmit Single TalkGroup Only Overheating, Please Turn Radio Off Party Busy Party Not Available Please Try Again Please Wait Connecting Registration Failure Repeater available Repeater not available Service Denied Service Not Available Service Restricted TalkGrp ... cannot be deleted Try Again Later Radio Disabled Unit is OK Warn:

Unit Not Attached 144 DRAFT MN001488A01-BF (en-US) Maintenance Appendix D Maintenance NOTICE:

Before using your radio for the first time, charge the battery until the LED lights green. Battery charging must occur only in non-hazardous areas. Ensure that radio connectors are clean and free of any debris before attaching accessories or a programming cable. Use a soft brush for cleaning contacts and do not use any chemicals or fluids in the cleaning process. D.1 Storage New Lithium-Ion batteries may be stored in ventilated, cool and dry areas with some capacity loss in the life cycle. It is not recommended to store the batteries when they are fully charged or discharged. D.2 Extending Battery Life A battery is an expendable part and may need replacing during the life of the radio. To ensure maximum service life of your radio, always replace the battery with a genuine Motorola Solutions replacement. D.3 Battery Charging Temperature Your charger only charges your battery when it is at temperature range of 1 C to 37 C. As the temperature gets colder (close to 0 C) less capacity is stored in the battery. If, during charging, the temperature is out of range, the battery might not be fully charged since the charging is temporarily stopped until the temperature becomes suitable. The temperature range of battery operation is from 0 C to +45 C in charger mode and from -30 C to +60 C in discharge mode. D.4 Additional Battery Warnings/Cautions To prevent injury, do not allow metal objects to touch the battery contacts. Do not disassemble. Do not throw in fire. Do not dispose of battery in household waste. NOTICE: When the battery is deeply discharged (for example after left unattended for months while connected to the radio), it cannot be recovered in all types of chargers. It is best recovered:

By charging the radio with the USB cable. In the rear pocket of a Dual Unit Charger. In a battery only pocket on a Multi-Unit Charger. 145 DRAFT MN001488A01-BF (en-US) Appendix D: Maintenance D.5 Looking after Your Radio Never leave your radio or battery in extreme temperatures, for example, behind a windscreen in direct sunlight. When the radio is not used together with an accessory, it is recommended to use an Accessory Connector Cover (part number PMHN4178A) to keep the connector clean and in good condition. To clean your radio, use a moistened or antistatic cloth. 146 DRAFT

 

 

en-US

fr-CA

es-LA

pt-BR

Caution Before using this device, read this booklet which contains important operating instructions. Compliance with RF Exposure Standards National and international regulations require manufacturers to comply with the RF energy exposure limits for mission critical devices before they can be marketed. Your Motorola Solutions device is designed, manufactured, and tested to comply with all applicable national and international regulations for human exposure to radio frequency electromagnetic energy. When mission critical devices are used as a consequence of employment, applicable regulations may require users to be fully aware of and able to control their exposure to meet occupational requirements. RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use Notice: This device is intended for use in occupational/

controlled conditions where users are aware of their exposure and can exercise control over their exposure to meet the requirements in national and international regulations. This device is not authorized for general population, consumer use. For more information on what RF energy exposure is, and how to control your exposure to ensure compliance with established RF exposure limits, consult the following websites:

https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en http://www.who.int/peh-emf/project/en/

For additional user training information on exposure requirements, consult the following websites:

https://www.motorolasolutions.com/en_us/about/company-overview/

corporate-responsibility/governance-and-policies/wireless-

communication-and-health-faqs.html http://learning.motorolasolutions.com/

English RF Exposure Compliance and Control Guidelines To control your exposure, and ensure compliance with the relevant RF exposure limits, always adhere to the following guidelines:

Do not remove any of the RF Exposure Labels if present from this device or its related accessories. Attach these instructions to the device when you transfer it to other Do not use this device if the operational requirements described users. herein are not met. Operating Instructions If your mission critical device operates similar to a mobile phone then hold your device at your ear when talking on it. When using the device's speaker to communicate, hold the device in a vertical position in front of the face with the microphone (and other parts of the device) at least one inch (2.5 centimeters) away from the nose and lips. When engaged in Push-To-Talk (PTT) communications, to transmit (talk), press the PTT button. To receive calls, release the PTT button. When worn on the body, always place the device in a Motorola Solutions approved clip, holder, holster, case, or body harness for this product. Special use cases for Mission Critical Devices Fixed Installation: The device operates from a fixed location with at least 20 cm distance between antennas and bystanders. Mobile Installation: The device operates on a vehicle with at least 20 cm distance between antennas and passangers or bystanders. For these special use cases, transmit only when people (bystanders and/or passengers) are at least at the recommended minimum distance

(as shown in Table 1 ) away from the antennas. This separation will ensure that there is sufficient distance from a properly installed

(according to the installation instructions) antenna to satisfy the relevant RF exposure limits. 1 English Table 1: Rated Power of Mission Critical Device and Recommended Minimum Distance from Antennas Rated Power Minimum Dis-

tance of Bystanders Less than 3.5 W 3.5 to 7 W 7 to 20 W 20 to 55 W Passengers from Antennas 8 in. (20 cm) 1 ft (30 cm) 2 ft (60 cm) 3 ft (90 cm) To ensure continued compliance with applicable RF exposure limits, use only Motorola Solutions approved, supplied or replacement batteries, and accessories. For a list of Motorola Solutions approved accessories please refer to your user manual or visit www.motorolasolutions.com Acoustic Safety Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the volume, the less time is required before your hearing could be affected. Hearing damage from loud noise is sometimes undetectable at first and can have a cumulative effect. To protect your hearing:

Use the lowest volume necessary to do your job. Turn up the volume only if you are in noisy surroundings. Turn down the volume before adding headset or earpiece. Limit the amount of time you use headsets or earpieces at high volume. When using the device without a headset or earpiece, do not place the loud speaker directly against your ear. Medical Devices If you use a personal medical device, such as a pacemaker or hearing aid, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. 2 Posted Facilities Switch your device off in any facility where posted notices require you to do so. Operational Warnings The following explains the operational warnings:

For Vehicle With Air Bags Warning:

Refer to vehicle manufacturers manual prior to installation of electronic equipment to avoid interference with air bag wiring. DO NOT mount or place a mission critical device in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a mission critical device is placed in the air bag deployment area and the air bag inflates, the device may be propelled with great force and cause serious injury to occupants of the vehicle. Potentially Explosive Atmospheres Warning:

Use of a mission critical device that is not intrinsically safe in a potentially explosive atmosphere could result in a serious injury or death. You should only use a certified Intrinsically Safe device in potentially explosive atmospheres. Explosive atmospheres refer to hazard classified locations that may contain hazardous gas, vapors, dusts, such as fueling areas below decks on boats, fuel or chemical transferor storage facilities, and areas where the air contains chemicals or particles such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often, but not always, posted. Turn off your device prior to entering any area with a potentially explosive atmosphere unless it is a device type specifically certified for use in hazardous location areas. DO NOT remove, install, or charge batteries in such areas, or remove or install antennas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. Batteries Charge your battery using the approved Motorola Solutions charger. Use the battery in accordance with its water and/or dust Ingress Protection (IP) rating. Do not discard your battery into a fire. Do not replace the battery in any area labeled "Hazardous Atmosphere". Do not disassemble, crush, puncture, shred, or otherwise attempt to change the form of your battery. Do not dry a wet or damp battery with an appliance or heat source, such as a hair dryer or microwave oven. Do not allow conductive material such as jewelry, keys, or beaded chains to touch exposed battery terminals. Do not dispose of batteries with household waste. European Union(EU) Waste of Electrical and Electronic Equipment (WEEE) Directive The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product

(or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries should not dispose of electronic and electrical equipment or accessories in household waste. Customers or end-users in EU countries should contact their local equipment supplier representative or service centre for information about the waste collection system in their country. English 3

Mise en garde Avant d'utiliser cet appareil, lisez cette brochure, qui contient d'importantes consignes d'utilisation. Conformit aux normes sur l'exposition aux radiofrquences Les rglementations nationales et internationales noncent que les fabricants doivent sassurer que leurs produits sont conformes aux limites dexposition l'nergie RF avant de les commercialiser. Votre appareil Motorola Solutions a t conu, fabriqu et test afin de garantir sa conformit aux normes nationales et internationales lies l'exposition des tres humains l'nergie lectromagntique de radiofrquence. Lorsque les appareils essentiels aux missions sont utiliss des fins professionnelles, la rglementation en vigueur exige que les utilisateurs soient pleinement conscients des effets de l'exposition et qu'ils soient capables de contrler le niveau d'exposition auquel ils se soumettent afin de rpondre aux exigences de leur profession. Information de sensibilisation et de gestion de l'exposition l'nergie RF, et consignes pour l'usage professionnel Avis: Cet appareil a t conu pour un usage professionnel dans un environnement contrl, o les utilisateurs sont pleinement conscients de l'exposition l'nergie RF laquelle ils sont soumis et peuvent exercer un contrle sur cette exposition afin de respecter les limites tablies par les rglements nationaux et internationaux. Cet appareil n'est pas autoris pour l'utilisation grand public par des consommateurs ordinaires. Visitez les sites Web suivants pour obtenir plus de renseignements sur ce qu'est l'nergie RF et sur les moyens de contrle prendre afin de respecter les limites tablies en matire d'exposition aux radiofrquences :

https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en Franais (Canada) http://www.who.int/peh-emf/project/en/

Pour plus de renseignements sur la formation des utilisateurs relativement aux limites d'exposition, consultez les sites suivants :

https://www.motorolasolutions.com/en_us/about/company-overview/

corporate-responsibility/governance-and-policies/wireless-

communication-and-health-faqs.html http://learning.motorolasolutions.com/

Directives de conformit et de contrle de l'exposition aux RF Pour contrler votre exposition et garantir le respect des limites d'exposition applicables, observez toujours les consignes suivantes. Ne pas retirer les tiquettes relatives l'exposition aux RF qui sont apposes sur cet appareil ou sur ses accessoires. Joignez ces directives l'appareil lorsque vous le transfrez d'autres utilisateurs. N'utilisez pas cet appareil si les conditions de fonctionnement dcrites aux prsentes ne sont pas runies. Consignes dutilisation Si votre appareil essentiel aux missions fonctionne de faon similaire un tlphone mobile, maintenez-le contre votre oreille lorsque vous l'utilisez pour parler. Lorsque vous utilisez le haut-parleur de l'appareil pour communiquer, tenez l'appareil la verticale devant le visage, en maintenant une distance d'au moins 2,5 centimtres (1 pouce) entre le micro (et les autres parties de l'appareil) et le nez ou les lvres. Durant une communication Push-To-Talk (PTT), pour mettre (parler), appuyez sur le bouton PTT. Pour recevoir les appels, relchez le bouton de transmission. Lorsque vous portez l'appareil sur vous, fixez-le toujours avec une pince ou une attache de ceinture et placez-le dans un tui ou un harnais approuv par Motorola Solutions pour utilisation avec ce produit. Cas d'utilisations spciales pour les appareils essentiels aux missions Installation fixe : L'appareil fonctionne partir d'un emplacement fixe avec au moins 20 cm de distance entre les antennes et les passants. 1 Franais (Canada) Installation mobile : L'appareil fonctionne dans un vhicule avec au moins 20 cm de distance entre les antennes et les passagers ou les passants. Dans ces cas d'utilisations spciales, n'mettez que lorsque les personnes (les passants ou les passagers) se trouvent au moins la distance minimum recommande (comme indiqu dans le Tableau 1) des antennes. Cet cart constitue une distance suffisante par rapport une antenne convenablement installe (conformment aux consignes dinstallation) pour rpondre aux exigences applicables en matire dexposition lnergie RF. Tableau 1: Puissance nominale de l'appareil essentiel aux missions et distance minimum recommande des antennes Puissance nominale et distance minimum des passants Moins de 3,5 W 3,5 - 7 W 7 - 20 W 20 - 55 W Distance des passagers des antennes 20 cm (8 po) 30 cm (1 pi) 60 cm (2 pi) 90 cm (3 pi) Pour assurer la conformit continue avec les limites d'exposition aux RF applicables, utilisez uniquement les batteries et les accessoires de remplacement fournis et approuvs par Motorola Solutions. Pour obtenir une liste des accessoires approuvs par Motorola Solutions, veuillez consulter votre manuel ou visitez le site www.motorolasolutions.com Protection de l'oue Une exposition des bruits forts en provenance de n'importe quelle source pendant de longues priodes pourrait affecter votre audition de manire temporaire ou permanente. Plus le volume sonore est lev, plus votre audition peut se dtriorer rapidement. Des dommages auditifs dus l'exposition des bruits forts peuvent d'abord tre indtectables, mais ceux-ci ont parfois des effets cumulatifs. Pour protger votre audition :

Rglez le volume le plus bas possible pour effectuer votre travail. 2 Montez le volume seulement si vous vous trouvez dans un environnement bruyant. Baissez le volume avant d'ajouter un casque ou une oreillette. Limitez la priode de temps d'utilisation de casques ou d'couteurs volume lev. Lorsque vous utilisez l'appareil sans casque ni couteur, ne placez pas le haut-parleur directement sur votre oreille. Appareils mdicaux Si vous utilisez un dispositif mdical personnel, comme un stimulateur cardiaque ou une prothse auditive, consultez le fabricant de votre appareil pour dterminer s'il est convenablement protg contre les RF. Votre mdecin peut vous aider obtenir ces renseignements. Avis affichs dans les installations teignez votre appareil dans toute installation o des avis vous obligent le faire. Avertissements de fonctionnement Le tableau suivant explique les avertissements de fonctionnement :

Pour vhicules quips de coussins gonflables Avertissement:

Consultez le manuel du fabricant du vhicule avant d'installer un appareil lectronique, afin d'viter toute interfrence avec le cblage des coussins gonflables. NE MONTEZ PAS ET NE PLACEZ PAS d'appareil essentiel aux missions dans la zone situe au-dessus d'un coussin gonflable ou dans la zone de dploiement de ce dernier. Un coussin gonflable de scurit se dploie avec beaucoup de force. Si un appareil essentiel aux missions se trouve dans la zone de dploiement du coussin, lorsque celui-ci se gonfle, l'appareil peut tre propuls avec une force considrable et risque alors d'occasionner de graves blessures aux passagers du vhicule. Atmosphres potentiellement explosives Avertissement:

L'utilisation d'un appareil essentiel aux missions autre qu'un appareil scurit intrinsque dans une atmosphre potentiellement explosive est susceptible d'entraner des blessures graves ou la mort. Vous devez utiliser uniquement un appareil scurit intrinsque agr dans des atmosphres potentiellement explosives. On retrouve des atmosphres explosives dans les lieux classs comme tant dangereux en raison de la prsence de gaz, de vapeurs et de poussires reprsentant un danger, par exemple, les zones d'avitaillement en carburant dans des cales de bateau, les installations de transfert et de stockage de carburant ou de produits chimiques, et les zones dans lesquelles l'air est charg en produits chimiques ou en particules telles que de la poudre de crales, de la poussire ou de la poudre mtallique. Les zones atmosphres potentiellement explosives affichent gnralement des panneaux de mise en garde, mais ce n'est pas toujours le cas. teignez l'appareil avant d'accder un lieu prsentant une atmosphre potentiellement explosive, moins qu'il s'agisse d'un type d'appareil certifi spcifiquement pour une utilisation dans des zones dangereuses. VITEZ d'enlever, d'installer ou de charger les batteries, ou d'enlever ou d'installer des antennes dans de tels lieux. Les tincelles dans des atmosphres potentiellement explosives peuvent provoquer une explosion ou un incendie et entraner des lsions corporelles, voire la mort. Batteries Chargez votre batterie l'aide du chargeur approuv par Motorola Solutions. Utilisez la batterie conformment son indice de protection (IP) contre l'eau et la poussire. Ne jetez pas votre batterie au feu. Ne remplacez pas la batterie dans un endroit qui porte la mention atmosphre dangereuse . Franais (Canada) Veillez ne pas dmonter, craser, percer, dcouper ou autrement modifier la forme de votre batterie. Ne faites pas scher une batterie mouille ou humide avec un appareil lectrique ou une source de chaleur, comme un schoir cheveux ou un four micro-ondes. Ne permettez pas des matriaux conducteurs, comme des bijoux, des cls ou des mailles de chane dentrer en contact avec les bornes de la batterie. Ne jetez pas les batteries avec les ordures domestiques. Directive sur la mise au rebut des quipements lectriques et lectroniques de l'Union europenne (UE)

(WEEE) La directive WEEE de l'Union europenne exige que les produits vendus dans les pays de l'UE portent l'tiquette de la poubelle barre (ou leur emballage, dans certains cas). Comme le dfinit la directive WEEE, cette tiquette de poubelle barre signifie que les clients et les utilisateurs finaux dans les pays de l'UE ne doivent pas jeter les quipements lectriques et lectroniques ou leurs accessoires dans les ordures domestiques. Les clients ou les utilisateurs finaux dans les pays de l'UE doivent communiquer avec le reprsentant ou le centre de service de leur fournisseur d'quipement pour obtenir des renseignements sur le systme de collecte des dchets de leur pays. 3

Precaucin Antes de utilizar este dispositivo, lea este folleto que contiene importantes instrucciones de funcionamiento. Conformidad con las normas sobre exposicin a la radiofrecuencia Las regulaciones nacionales e internacionales obligan a que los fabricantes cumplan con los lmites de exposicin a energa de radiofrecuencia para dispositivos de misin crtica antes de que se puedan comercializar. El dispositivo Motorola Solutions est diseado, fabricado y probado para cumplir con todas las regulaciones nacionales e internacionales correspondientes en materia de exposicin humana a la energa electromagntica de radiofrecuencia. Cuando los dispositivos de misin crtica se usan para trabajar, las regulaciones correspondientes podran exigir que los usuarios conozcan y controlen su nivel de exposicin para cumplir con los requisitos de uso profesional. Conocimiento de la exposicin a energa de radiofrecuencia, informacin de control e instrucciones de funcionamiento para uso ocupacional Nota: Este dispositivo est diseado para usarse en condiciones controladas o profesionales, donde los usuarios tengan pleno conocimiento de su exposicin y puedan controlarla con el fin de cumplir con los requisitos de las regulaciones nacionales e internacionales. Este dispositivo no est autorizado para el uso particular de la poblacin en general. Para obtener ms informacin sobre el significado de la exposicin a energa de radiofrecuencia y cmo controlar la exposicin con el fin de asegurar el cumplimiento de los lmites de exposicin a radiofrecuencias establecidos, consulte los siguientes sitios web:

https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en http://www.who.int/peh-emf/project/en/

Espaol (Latinoamrica) Para obtener informacin adicional de la capacitacin de los usuarios sobre los requisitos de exposicin, consulte los siguientes sitios web:

https://www.motorolasolutions.com/en_us/about/company-overview/

corporate-responsibility/governance-and-policies/wireless-

communication-and-health-faqs.html http://learning.motorolasolutions.com/

Cumplimiento de exposicin a radiofrecuencia y pautas de control Para controlar la exposicin y garantizar el cumplimiento de los lmites de exposicin a radiofrecuencias correspondientes, respete siempre las siguientes pautas:

No retire ninguna de las etiquetas de exposicin a radiofrecuencias, si las hubiere, de este dispositivo o sus accesorios respectivos. Adjunte estas instrucciones al dispositivo cuando se lo transfiera a otros usuarios. No utilice este dispositivo si no se cumple con los requisitos de funcionamiento descritos en este documento. Instrucciones de funcionamiento Si su dispositivo de misin crtica funciona de forma similar a un telfono mvil, mantenga el dispositivo en la oreja cuando hable en l. Cuando utilice el altavoz del dispositivo para comunicarse, sostenga el radio en posicin vertical frente a la cara con el micrfono (y otras partes del dispositivo) a al menos 2,5 cm (1 pulg.) de distancia de la nariz y los labios. Cuando participe en comunicaciones Push-To-Talk

(PTT), para transmitir (hablar) presione el botn PTT. Para recibir llamadas, suelte el botn PTT. Siempre que use el dispositivo ajustado al cuerpo, pngalo en un clip, un soporte, un estuche, una funda o un arns para el cuerpo aprobado por Motorola Solutions para este producto. Casos de uso especiales para dispositivos de misin crtica Instalacin fija: El dispositivo funciona desde una ubicacin fija con una distancia mnima de 20 cm (7,8 pulg.) entre antenas y personas presentes. 1 Espaol (Latinoamrica) Instalacin mvil: El dispositivo funciona en un vehculo con una distancia mnima de 20 cm (7,8 pulg.) entre antenas y pasajero o personas presentes. Para estos casos de uso especial, transmita solo cuando las personas

(personas presentes o pasajeros) estn por lo menos a la distancia mnima recomendada (como se muestra en la Tabla 1) de las antenas. Con esta separacin se garantiza que haya una distancia suficiente entre una antena instalada correctamente (segn las instrucciones de instalacin) para cumplir con los lmites de exposicin a radiofrecuencia correspondientes. Tabla 1: Potencia nominal del dispositivo de misin crtica y distancia mnima recomendada de las antenas Potencia nominal a una distancia mnima de las personas presentes Menor que 3,5 W De 3,5 a 7 W De 7 a 20 W De 20 a 55 W Pasajeros de las antenas 8 pulg. (20 cm) 1 pie (30 cm) 2 pies (60 cm) 3 pies (90 cm) Para garantizar el cumplimiento continuo de los lmites de exposicin a radiofrecuencia correspondientes, utilice solamente las bateras y los accesorios de repuesto suministrados o aprobados por Motorola Solutions. Para obtener una lista de los accesorios aprobados por Motorola Solutions, consulte el manual del usuario o visite www.motorolasolutions.com. Seguridad acstica La exposicin a ruidos fuertes de cualquier fuente durante perodos prolongados podra afectar la audicin de manera temporal o permanente. Cuanto ms alto sea el volumen, ms rpido se ver afectada su audicin. En ocasiones, el dao a la audicin provocado por ruidos fuertes es indetectable en un principio y puede tener efecto acumulativo. Para proteger la audicin:

2 Utilice el volumen ms bajo que necesite para hacer su trabajo. Aumente el volumen solo si se encuentra en un ambiente ruidoso. Reduzca el volumen antes de conectar los auriculares o el audfono. Limite el tiempo durante el cual usa los auriculares o los audfonos a volumen alto. Cuando use el dispositivo sin audfonos o auriculares, no coloque el altavoz directamente en la oreja. Aparatos mdicos Si utiliza un dispositivo mdico, como un marcapasos o una prtesis auditiva, consulte al fabricante del dispositivo para determinar si est adecuadamente protegido contra las energas de radiofrecuencia. Su mdico podra ayudarlo a obtener esta informacin. Publicaciones en instalaciones Apague su dispositivo en cualquier instalacin donde los avisos publicados requieran que lo haga. Advertencias de funcionamiento A continuacin, se explican las advertencias de funcionamiento:

Para vehculos con airbags Advertencia:

Consulte el manual del fabricante del vehculo antes de instalar equipos electrnicos para evitar la interferencia con el cableado de las bolsas de aire. NO instale ni ubique un dispositivo de misin crtica en el rea que se encuentra encima de la bolsa de aire ni en el rea de despliegue de esta. Las bolsas de aire se inflan con mucha fuerza. Si se pone un dispositivo de misin crtica en el rea de despliegue de la bolsa de aire y esta se infla, es posible que el dispositivo salga disparado con gran fuerza y cause lesiones graves a los ocupantes del vehculo. Atmsferas potencialmente explosivas Advertencia:

El uso de un dispositivo de misin crtica que no sea intrnsecamente seguro en una atmsfera potencialmente explosiva puede provocar lesiones graves o la muerte. En atmsferas potencialmente explosivas, debe utilizar solamente un dispositivo intrnsecamente seguro certificado. El trmino atmsferas explosivas se refiere a lugares clasificados como peligrosos en los que podra haber gases, vapores o polvos peligrosos, como reas con combustibles bajo las cubiertas de los botes o instalaciones de almacenamiento o transferencia de qumicos, y reas en que el aire contenga productos qumicos o partculas, como material granulado, polvo o polvo metlico. En las reas con atmsferas potencialmente explosivas generalmente hay seales de precaucin, aunque no siempre es as. Apague el dispositivo antes de ingresar en cualquier rea que posea una atmsfera potencialmente explosiva, a menos que se trate de un tipo de dispositivo certificado especficamente para ser usado en zonas de ubicaciones peligrosas. NO retire, instale ni cargue bateras, ni tampoco retire o instale antenas en dichas reas. Las chispas en ambientes potencialmente explosivos pueden desencadenar una explosin o un incendio, y ocasionar lesiones o incluso la muerte. Bateras Cargue la batera con cargadores aprobados por Motorola Solutions. Utilice la batera de acuerdo con su clasificacin de proteccin de ingreso (IP) contra polvo y agua. No arroje la batera al fuego. No cambie la batera en un rea designada como Atmsfera peligrosa. No desarme, rompa, perfore, triture ni intente cambiar de ningn otro modo la forma de la batera. No intente secar una batera mojada o hmeda con un electrodomstico o una fuente de calor externa, como un secador de pelo o un horno microondas. No permita que materiales conductores como joyas, llaves o cadenas hagan contacto con los terminales expuestos de la batera. No bote las bateras en la basura domstica. Espaol (Latinoamrica) Directiva de Residuos de Aparatos Elctricos y Electrnicos (RAEE) de la Unin Europea (UE) La Directiva RAEE de la Unin Europea requiere que los productos que se venden en los pases de la UE tengan la etiqueta de un bote de residuos tachado sobre el producto (o en el paquete, en algunos casos). Como define la directiva RAEE, esta etiqueta con un bote de basura tachado indica que los clientes y los usuarios finales en los pases de la UE no deben deshacerse de los equipos o accesorios elctricos y electrnicos con la basura domstica. Los clientes o los usuarios finales en los pases de la UE deben ponerse en contacto con su representante distribuidor de equipos o el centro de servicio locales para obtener informacin sobre el sistema de recoleccin de residuos de su pas. 3

Ateno Antes de usar o dispositivo, leia este folheto que contm instrues operacionais importantes. Conformidade com os Padres de Exposio RF Os regulamentos nacionais e internacionais exigem que os fabricantes estejam em conformidade com os limites de exposio energia de RF para dispositivos de misso crtica antes de serem comercializados. Seu dispositivo da Motorola Solutions foi projetado, fabricado e testado para estar em conformidade com todos os regulamentos nacionais e internacionais aplicveis para exposio humana energia eletromagntica de radiofrequncia. Ao usar dispositivos de misso crtica por motivos de trabalho, os regulamentos aplicveis podem exigir que os usurios estejam totalmente conscientes e aptos a controlar sua exposio de modo a atender s exigncias ocupacionais. Informaes sobre Conscientizao e Controle de Exposio Energia de RF e Instrues Operacionais para o Uso Ocupacional Comunicado: Este dispositivo destina-se ao uso em condies ocupacionais/controladas, em que os usurios estejam cientes de sua exposio e possam exercer controle sobre ela, para atender aos requisitos nos regulamentos nacionais e internacionais. O uso deste dispositivo pela populao em geral no autorizado. Para obter mais informaes sobre a exposio energia de RF e como controlar a exposio para garantir a conformidade com os limites de exposio RF estabelecidos, acesse os seguintes sites:

https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en http://www.who.int/peh-emf/project/en/

Para informaes adicionais de treinamento sobre os requisitos de exposio, acesse os seguintes sites:

https://www.motorolasolutions.com/en_us/about/company-overview/

corporate-responsibility/governance-and-policies/wireless-

communication-and-health-faqs.html Portugus (Brasil) http://learning.motorolasolutions.com/

Diretrizes de Conformidade e Controle de Exposio RF Para controlar a exposio e garantir a conformidade com os limites de exposio RF em questo, siga sempre as diretrizes a seguir:

No remova as Etiquetas de Exposio RF, se houverem, do dispositivo ou acessrios relacionados. Anexe essas instrues ao dispositivo quando o transferir a outros No use este dispositivo se os requisitos operacionais descritos aqui usurios. no forem atendidos. Instrues Operacionais Caso seu dispositivo de misso crtica opere de forma similar a um telefone celular, ento basta manter o dispositivo prximo ao ouvido ao us-lo. Ao utilizar o alto-falante do dispositivo para se comunicar, segure o dispositivo em posio vertical em frente ao rosto com o microfone (e outras partes do dispositivo) a pelo menos 2,5 centmetros (1 polegada) de distncia do nariz e dos lbios. Quando o modo PTT

(Push-to-Talk) estiver em uso, pressione o boto PTT para transmitir

(falar). Para receber chamadas, solte o boto PTT (Push-To-Talk, apertar para falar). Ao usar o dispositivo junto ao corpo, sempre o coloque em um prendedor, suporte, suporte para cinto ou estojo para este produto aprovado pela Motorola Solutions. Casos de usos especiais para Dispositivos de Misso Crtica Instalao Fixa: O aparelho opera a partir de um local fixo com, pelo menos, 20 cm de distncia entre as antenas e os presentes. Instalao mvel: O aparelho opera em um veculo com, pelo menos, 20 cm de distncia entre as antenas e os passageiros. Para estes casos de usos especiais, transmita apenas quando as pessoas (presentes e/ou passageiros) estiverem dentro da distncia mnima recomendada (conforme a Tabela 1) das antenas. Essa separao garantir que haja distncia suficiente de uma antena instalada (de acordo com as instrues de instalao) para atender aos limites de exposio RF em questo. 1 Portugus (Brasil) Tabela 1: Potncia Nominal de Dispositivo de Misso Crtica aparelho e Distncia Mnima Recomendada das Antenas Potncia Nominal Distncia Mnima dos Presentes Inferior a 3,5 W 3,5 a 7 W 7 a 20 W 20 a 55 W Passageiros das Antenas 20 cm (8 polegadas) 30 cm (1 p) 60 cm (2 ps) 90 cm (3 ps) Para garantir constantemente a conformidade com os limites aplicveis de exposio RF, use apenas baterias e acessrios de reposio aprovados ou fornecidos pela Motorola Solutions. Para obter uma lista dos acessrios aprovados pela Motorola Solutions, consulte o manual do usurio ou acesse www.motorolasolutions.com Segurana Acstica A exposio a rudos muito altos de qualquer origem por longos perodos pode prejudicar sua audio temporria ou permanentemente. Quanto mais alto for o volume, em menos tempo sua audio poder ser prejudicada. s vezes, os danos auditivos causados por rudos fortes no so detectados em sua fase inicial e podem ter efeito cumulativo. Para proteger sua audio:

Use o volume mais baixo necessrio para a execuo da sua tarefa. Aumente o volume somente se estiver em ambientes barulhentos. Reduza o volume antes de conectar o headset ou o fone de ouvido. Limite o tempo de uso dos headsets ou fones de ouvido com volume alto. Ao usar o dispositivo sem monofones ou fones de ouvido, no coloque o alto-falante diretamente em contato com seus ouvidos. Equipamentos Mdicos Se voc usa um dispositivo mdico pessoal, como um marca-passo ou aparelho auditivo, consulte o fabricante do dispositivo para determinar 2 se est adequadamente protegido contra energia de RF. Seu mdico pode ajud-lo a obter essas informaes. reas sinalizadas Desligue seu dispositivo em reas com avisos solicitando tal ao. Avisos Operacionais A seguir so explicados os avisos operacionais:

Para Veculos Equipados com Air Bags Aviso:

Consulte o manual do fabricante do veculo antes de instalar equipamentos eletrnicos para evitar interferncia com o funcionamento do air bag. NO instale nem coloque um dispositivo de misso crtica sobre um air bag ou sobre a rea de expanso dos air bags. Os air bags inflam com muita fora. Se um dispositivo de misso crtica estiver posicionado na rea de abertura do air bag e ele inflar, o dispositivo poder ser impelido com grande fora e causar graves ferimentos aos ocupantes do veculo. Ambientes Potencialmente Explosivos Aviso:

O uso de um dispositivo de misso crtica que no intrinsecamente seguro em um ambiente potencialmente explosivo poder resultar em danos graves e at em morte. Voc deve usar apenas um dispositivo Intrinsecamente Seguro certificado em ambientes potencialmente explosivos. Ambientes potencialmente explosivos referem-se a locais classificados como de risco que podem conter gases, vapores ou ps nocivos, como reas de abastecimento embaixo do convs principal em barcos, instalaes de armazenamento ou transferncia de produtos qumicos ou combustvel e reas onde o ar contm partculas ou elementos qumicos, como fibras, poeira ou ps metlicos. As reas com ambientes potencialmente explosivos so frequentes, mas nem sempre h avisos sobre isso. Desligue o dispositivo antes de entrar em qualquer rea com ambientes potencialmente explosivos, a menos que o tipo de dispositivo seja especificamente certificado para utilizao em reas de risco. NO remova, instale ou carregue baterias nessas reas, nem remova ou instale antenas. Fascas em um ambiente potencialmente explosivo podem causar uma exploso ou incndio que pode resultar em ferimentos e, at mesmo, morte. Portugus (Brasil) Baterias Sempre carregue a bateria usando o carregador aprovado pela Use a bateria de acordo com sua classificao de Proteo contra Motorola Solutions. entrada (IP) de p e gua. No descarte a bateria no fogo. No troque a bateria em lugares identificados como "Atmosferas Potencialmente Perigosas". No desmonte, comprima, perfure, fragmente nem tente alterar de outra maneira a forma da bateria. No seque baterias molhadas nem midas usando aparelhos ou fontes de calor, como secadores de cabelo ou fornos de micro-ondas. No permita que materiais condutores como joias, chaves ou correntes toquem os terminais expostos da bateria. No descarte baterias no lixo domstico. Diretiva de Resduos de Equipamentos Eltricos e Eletrnicos (WEEE) para a Unio Europeia (UE) A Diretiva de WEEE da Unio Europeia exige que os produtos vendidos nos pases da UE tenham a etiqueta de lixeira riscada no produto (ou no pacote, em alguns casos). Conforme definido pela diretiva WEEE, essa etiqueta de lixeira cruzada indica que os clientes e os usurios nos pases da UE no devem descartar equipamentos ou acessrios eltricos ou eletrnicos em lixo domstico. Os clientes ou os usurios nos pases da UE devem entrar em contato com o representante local do fornecedor do equipamento ou com a central de servios para obter informaes sobre o sistema de coleta de lixo em seu pas. 3

MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. 201 Motorola Solutions, Inc. All rights reserved. Printed in

-