FCC ID: AZ489FT7111 2-Way Mobile Radio (with Bluetooth, Bluetooth LE and WIFI)

APX TWO-WAY RADIOS MODEL 1.5 APX 8000HXE USER GUIDE MAY 2020 2020 Motorola Solutions, Inc. All rights reserved

*MN006727A01*

MN006727A01-AA MN006727A01-AA Contents Contents List of Tables............................................................................................................... 8 Software Version.........................................................................................................9 Read Me First.............................................................................................................10 1.1 Notations Used in This Manual..............................................................................................10 1.2 Radio Care.............................................................................................................................11 1.2.1 Cleaning Your Radio................................................................................................12 1.2.2 Cleaning the External Surface of the Radio.............................................................12 1.2.3 Radio Service and Repair........................................................................................ 13 1.3 Battery Recycling and Disposal............................................................................................. 13 1.4 Additional Performance Enhancement.................................................................................. 13 1.4.1 ASTRO 25 Enhanced Data......................................................................................13 1.4.2 Dynamic System Resilience.................................................................................... 13 1.4.3 CrossTalk Prevention...............................................................................................14 1.4.4 Encrypted Integrated Data....................................................................................... 14 1.4.5 SecureNet................................................................................................................ 14 1.4.6 P25 Digital Vehicular Repeater System...................................................................14 1.4.7 Conventional Talkgroup and Radio Scan Enhancements....................................... 14 1.5 What Your Dealer/System Administrator Can Tell You......................................................... 15 Preparing Your Radio for Use..................................................................................16 2.1 Charging the Battery..............................................................................................................16 2.2 Attaching the Battery ............................................................................................................ 16 2.3 Attaching the Antenna........................................................................................................... 17 2.4 Removing and Attaching the Accessory Connector Cover....................................................18 2.5 Using the Carry Holder.......................................................................................................... 19 2.6 Attaching the Belt Clip........................................................................................................... 20 2.7 Turning On the Radio ........................................................................................................... 21 2.8 Adjusting the Volume.............................................................................................................22 Radio Controls...........................................................................................................23 3.1 Radio Parts and Controls.......................................................................................................23 3.2 Programmable Features........................................................................................................ 24 3.2.1 Assignable Radio Functions.................................................................................... 24 3.2.2 Assignable Settings or Utility Functions...................................................................26 Status Indicators....................................................................................................... 27 4.1 Battery Charge Status........................................................................................................... 27 4.1.1 Fuel Gauge Icons.....................................................................................................27 2 MN006727A01-AA Contents 4.1.2 HAZLOC Battery Type Detection.............................................................................27 4.2 LED Indications......................................................................................................................28 4.3 Status Icons........................................................................................................................... 28 4.4 Intelligent Lighting Indicators................................................................................................. 31 4.5 Alert Tones ........................................................................................................................... 31 4.6 Display Color Change On Channel........................................................................................33 General Radio Operation..........................................................................................35 5.1 Selecting a Zone....................................................................................................................35 5.2 Selecting a Radio Channel.................................................................................................... 35 5.3 Receiving and Responding to a Radio Call........................................................................... 35 5.3.1 Receiving and Responding to a Talkgroup Call.......................................................35 5.3.2 Receiving and Responding to a Private Call (Trunking Only)..................................36 5.3.3 Receiving and Responding to a Telephone Call (Trunking Only)............................ 36 5.4 Methods to Make a Radio Call...............................................................................................36 5.4.1 Making a Talkgroup Call ......................................................................................... 37 5.4.2 Making a Private Call (Trunking Only)..................................................................... 37 5.4.3 Making an Enhanced Private Call (Trunking Only).................................................. 37 5.5 Switching Between Repeater or Direct Operation Button......................................................38 5.6 Monitor Feature..................................................................................................................... 38 5.6.1 Monitoring a Channel...............................................................................................38 5.6.2 Monitoring Conventional Mode................................................................................ 39 Advanced Features................................................................................................... 40 6.1 Advanced Call Features........................................................................................................ 40 6.1.1 Selective Call (ASTRO Conventional Only)............................................................. 40 6.1.1.1 Receiving a Selective Call..........................................................................40 6.1.1.2 Making a Selective Call..............................................................................40 6.1.2 Making a Priority Dispatch Calls.............................................................................. 40 6.1.3 Dynamic Regrouping (Trunking Only)......................................................................41 6.1.3.1 Classification of Regrouped Radios........................................................... 41 6.1.3.2 Requesting a Reprogram (Trunking Only)................................................. 42 6.2 Scan Lists.............................................................................................................................. 42 6.2.1 Intelligent Priority Scan............................................................................................ 42 6.2.2 Viewing a Scan List..................................................................................................42 6.2.3 Viewing and Changing the Priority Status................................................................42 6.3 Scan.......................................................................................................................................43 6.3.1 Turning Scan On or Off............................................................................................43 6.3.2 Making a Dynamic Priority Change (Conventional Scan Only)................................43 6.3.3 Deleting a Nuisance Channel.................................................................................. 43 6.3.4 Restoring a Nuisance Channel................................................................................ 44 3 MN006727A01-AA Contents 6.4 Call Alert Paging.................................................................................................................... 44 6.4.1 Receiving a Call Alert Page..................................................................................... 44 6.4.2 Sending a Call Alert Page........................................................................................44 6.5 Emergency Operation............................................................................................................45 6.5.1 Special Considerations for Emergency Operation................................................... 45 6.5.2 Emergency Keep-Alive............................................................................................ 46 6.5.3 Exiting Emergency Operation.................................................................................. 46 6.5.4 Exiting Emergency as Supervisor (Trunking Only).................................................. 46 6.5.5 Sending an Emergency Alarm................................................................................. 47 6.5.6 Sending an Emergency Call (Trunking Only)...........................................................47 6.5.7 Sending An Emergency Call With Hot Mic (Trunking Only).....................................47 6.5.8 Sending an Emergency Alarm with Emergency Call............................................... 48 6.5.9 Sending An Emergency Alarm and Call with Hot Mic.............................................. 49 6.5.10 Sending a Silent Emergency Alarm....................................................................... 49 6.5.11 Emergency Find Me...............................................................................................49 6.5.11.1 Sending and Receiving Emergency Find Me Beacon..............................50 6.6 Fireground............................................................................................................................. 50 6.6.1 Entering Fireground Zone Channel (Conventional)................................................. 50 6.6.2 Sending Evacuation Tone........................................................................................51 6.6.3 Responding to Evacuation Indicator........................................................................ 51 6.7 Tactical Public Safety (Conventional Only)............................................................................52 6.7.1 Using TPS Normal Transmission.............................................................................52 6.7.2 Using TPS Emergency Transmission...................................................................... 52 6.8 Man Down..............................................................................................................................52 6.8.1 Radio Alerts When Man Down is Triggered.............................................................53 6.8.2 Testing the Man Down Feature................................................................................53 6.8.3 Exiting Man Down.................................................................................................... 53 6.8.4 Re-Initiating Man Down............................................................................................54 6.9 Secure Operations.................................................................................................................54 6.9.1 Selecting Secure Transmissions..............................................................................54 6.9.2 Selecting Clear Transmissions ............................................................................... 54 6.9.3 Managing Encryption............................................................................................... 55 6.9.3.1 Loading Encryption Keys........................................................................... 55 6.9.3.2 Multikey Feature.........................................................................................55 6.9.3.3 Erasing Encryption Keys............................................................................ 55 6.9.3.4 Requesting an Over-the-Air Rekey............................................................ 56 6.9.3.5 MDC OTAR (Conventional Only)............................................................... 56 6.9.3.6 Infinite UKEK Retention............................................................................. 56 6.9.3.7 Hear Clear..................................................................................................56 4 MN006727A01-AA Contents 6.10 Radio Inhibit.........................................................................................................................57 6.11 Global Positioning System/Global Navigation Satellite System...........................................57 6.11.1 GPS Performance Enhancement...........................................................................57 6.11.2 Location Format..................................................................................................... 58 6.11.3 Location Feature in Emergency Mode................................................................... 58 6.12 Mission Critical Geofence (ASTRO 25 Trunking)................................................................ 58 6.12.1 Entering the Geofence Area.................................................................................. 58 6.12.2 Mission Critical Geofence...................................................................................... 59 6.12.3 Entering Mission Critical Geofence........................................................................59 6.12.4 Exiting Mission Critical Geofence.......................................................................... 59 6.13 Trunking System Controls................................................................................................... 60 6.13.1 Operating in Failsoft System..................................................................................60 6.13.2 Out-of-Range Radio...............................................................................................60 6.13.3 SmartConnect........................................................................................................ 60 6.13.4 Site Trunking Feature............................................................................................ 61 6.13.5 Locking and Unlocking a Site.................................................................................61 6.13.6 Viewing the Current Site........................................................................................ 61 6.13.7 Changing the Current Site..................................................................................... 61 6.14 Mission Critical Wireless Bluetooth ................................................................................... 61 6.14.1 Turning On Bluetooth ............................................................................................62 6.14.2 Turning Off the Bluetooth.......................................................................................62 6.14.3 Pairing with Low Frequency-Motorola Proximity Pairing (LF-MPP) Feature..........62 6.14.4 Standard Pairing Feature.......................................................................................63 6.14.4.1 Searching and Pairing the Bluetooth Device............................................63 6.14.4.2 Turning On Bluetooth Visibility................................................................. 64 6.14.4.3 Receiving Pairing Request from other Devices........................................64 6.14.5 Turning On the Bluetooth Audio.............................................................................65 6.14.6 Turning Off the Bluetooth Audio.............................................................................65 6.14.7 Adjusting the Volume of the Radio from Bluetooth Audio Device.......................... 65 6.14.8 Clearing All Bluetooth Devices Information............................................................65 6.14.9 Pairing with LEX Handheld.................................................................................... 66 6.14.10 Responder Alert Sensors.....................................................................................66 6.14.10.1 Holster Sensor....................................................................................... 67 6.14.10.2 Weapon Fired Sensor............................................................................ 67 6.14.10.3 Vest Pierced Sensor.............................................................................. 67 6.14.10.4 Disabling the Sensor.............................................................................. 67 6.15 ASTRO 25 (P25) Programming Over Project 25 (POP25).................................................. 68 6.15.1 Responding to the Notification of Upgrade............................................................ 68 6.16 Voice Announcement ..........................................................................................................69 5 MN006727A01-AA Contents 6.17 Site Selectable Alerts (ASTRO 25 Trunking).......................................................................69 6.18 Wi-Fi.................................................................................................................................... 69 6.18.1 Turning Wi-Fi On or Off..........................................................................................69 6.18.2 Checking the Wi-Fi Configuration and Status of the Radio....................................70 6.19 Utilities................................................................................................................................. 70 6.19.1 Using the Flip Display............................................................................................ 70 6.19.2 Selecting a Basic Zone Bank................................................................................. 70 6.19.3 Selecting the Power Level..................................................................................... 71 6.19.4 Controlling the Display Backlight........................................................................... 71 6.19.5 Locking and Unlocking the Controls...................................................................... 71 6.19.6 Turning Voice Mute On or Off................................................................................ 72 6.19.7 Using the Time-Out Timer......................................................................................72 6.19.8 Conventional Squelch Operation........................................................................... 72 6.19.8.1 Using Conventional Squelch Operation Features.................................... 73 6.19.9 Using the PL Defeat Feature................................................................................. 73 6.19.10 Digital PTT ID Support......................................................................................... 73 6.19.11 Smart PTT (Conventional Only)...........................................................................74 6.19.12 Transmit Inhibit.................................................................................................... 74 6.19.12.1 Enabling Transmit Inhibition...................................................................74 6.19.12.2 Disabling Transmit Inhibition.................................................................. 75 6.19.13 Instant Recall....................................................................................................... 75 6.19.13.1 Saving and Playback Calls.....................................................................75 Accessories............................................................................................................... 76 Legal and Compliance Statement............................................................................77 Disclaimer.................................................................................................................................... 77 Copyrights....................................................................................................................................77 Declaration of Conformity............................................................................................................ 78 Important Safety Information....................................................................................................... 79 Notice to Users (FCC)................................................................................................................. 79 FCC Licensing Information............................................................................................... 79 Canada Licensing Information..................................................................................................... 80 Maritime Radio Use in the VHF Frequency Range................................................. 81 Special Channel Assignments..................................................................................................... 81 Emergency Channel......................................................................................................... 81 Non-Commercial Call Channel......................................................................................... 81 Operating Frequency Requirements............................................................................................81 Declaration of Compliance for the Use of Distress and Safety Frequencies............................... 84 Technical Parameters for Interfacing External Data Sources......................................................84 Limited Warranty.......................................................................................................85 6 MN006727A01-AA Contents MOTOROLA SOLUTIONS COMMUNICATION PRODUCTS..................................................... 85 I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:................................................. 85 II. GENERAL PROVISIONS:....................................................................................................... 86 III. STATE LAW RIGHTS:............................................................................................................86 IV. HOW TO GET WARRANTY SERVICE:.................................................................................86 V. WHAT THIS WARRANTY DOES NOT COVER:.................................................................... 86 VI. PATENT AND SOFTWARE PROVISIONS:...........................................................................87 VII. GOVERNING LAW:...............................................................................................................88 VIII. For Australia Only.................................................................................................................88 Glossary.....................................................................................................................89 7 MN006727A01-AA List of Tables List of Tables Table 1: LED Indications........................................................................................................................ 28 Table 2: Emergency Operation Scenarios..............................................................................................45 Table 3: VHF Marine Channel List......................................................................................................... 82 8 MN006727A01-AA Software Version Software Version All the features described in the following sections are supported by the software version R21.00.00 or later. Contact your system administrator for more details of all the supported features. 9 MN006727A01-AA Read Me First Read Me First This User Guide covers the basic operation of the radio. However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information. 1.1 Notations Used in This Manual Notations such as Warning, Caution, and Notice are used throughout the text in this publication. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed. WARNING: An operational procedure, practice, or condition and so on, which may result in injury or death if not carefully observed. CAUTION: An operational procedure, practice, or condition and so on, which may result in damage to the equipment if not carefully observed. NOTICE: An operational procedure, practice, or condition and so on, which is essential to emphasize. 10 MN006727A01-AA Read Me First 1.2 Radio Care Proper radio usage and care ensure efficient operation and long life of the product. CAUTION: Use the radio according to the following recommendations and warnings. Your radio casing has a vent port for pressure equalization in the radio. Never poke this vent with objects such as needles, tweezers, or screwdrivers. Poking the vent could create leak paths into the radio and the radio submergibility will be lost. Never obstruct or cover the vent port, even with a label. Ensure that no oily substances come in contact with the vent port. Your radio is designed to be submerged to a maximum depth of 2 meters, with a maximum submersion time of 4 hours. Exceeding either maximum limit may result in damage to the radio. Elastomer seals used in portable radios age with time and environmental exposure. To ensure the waterseal integrity of the radio, Motorola Solutions recommends that radios be checked annually as a preventive measure. The disassembly, test, and reassembly procedures along with necessary test equipment are available in the Service Manual. If the radio battery contacts are exposed to water without the battery attached, dry and clean the radio battery contacts before attaching a battery to the radio. Turn the radio over with the battery contact facing down and shake the radio so any trapped water can escape. A short circuit of the contacts could occur if they are not dried properly. If the radio has been submerged in water, shake the radio to remove any water that is trapped inside the speaker grille and microphone port. Otherwise, the water decreases the audio quality of the radio. If an accessory is not attached to the radio, ensure that the accessory connector cover is attached to the radio side accessory connector. If the radio is submerged or exposed to a high force water spray, such as from a hose, remove the accessory or accessory connector cover immediately and ensure that no water is forced into the accessory connector/radio interface. Rinse and dry the area and re-attach the accessory or accessory connector cover if leakage occurs. 11 A MN006727A01-AA Read Me First If the radio is exposed to a corrosive environment, such as salt water or corrosive gases or liquids, rinse and clean the radio immediately to prevent damage to radio materials, especially plated surfaces. Remove the battery and the antenna before cleaning. Do not disassemble the radio as you could damage radio seals and result in leak paths into the radio. Any radio maintenance should be performed only by a qualified radio technician. Only Underwriter Laboratory (UL) approved service centers can open and service UL certified radios. Opening or repairing at unauthorized locations invalidates hazardous location rating of the radio. Do not pound, drop, or throw the radio unnecessarily. Turn off the radio when charging the radio using a wall-mounted charger. Otherwise, the Man Down Alert and Emergency may be accidentally triggered. When cleaning the radio, do not use a high-pressure jet spray as this may exceed the depth pressure and cause water to leak into the radio. 1.2.1 Cleaning Your Radio CAUTION: Do not use solvents or disinfectants to clean your radio as these chemicals may permanently damage the radio housing, seals, and adhesives. To clean the external surfaces of your radio, follow the procedure described next. Procedure:

1 Combine one teaspoon of mild dishwashing detergent to one gallon of water (0.5% solution). 2 Apply the solution sparingly with a stiff, non-metallic, shortbristled brush, making sure that excess detergent does not get entrapped near the connectors, controls, or crevices. Rinse and then dry the radio thoroughly with a soft, lint-free cloth. 3 Clean battery contacts with a lint-free cloth to remove dirt or grease. 1.2.2 Cleaning the External Surface of the Radio CAUTION: Do not use solvents to clean your radio. Spirits may permanently damage the radio housing. Do not submerge the radio in detergent solution. 1 Combine 1 teaspoon of mild dishwashing detergent to 1 gallon of water (0.5% solution). 2 Apply the solution sparingly with a stiff, non-metallic, short-bristled brush, ensuring that excess detergent does not get entrapped near the connectors, controls, or crevices. 3 Dry the radio thoroughly with a soft, absorbent, lint-free cloth. 4 Ensure that no water remains entrapped near the connectors, cracks, or crevices. Prerequisites:

Procedure:

12 MN006727A01-AA Read Me First 1.2.3 Radio Service and Repair Proper repair and maintenance procedures ensure efficient operation and long life of this radio. A Motorola Solutions maintenance agreement provides expert service to keep the radio and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola Solutions to support maintenance services. Through its maintenance and installation program, Motorola Solutions makes the finest service available to those desiring reliable continuous communications on a contract basis. For a contract service agreement, contact your nearest Motorola Solutions service or sales representative, or an authorized Motorola Solutions dealer. 1.3 Battery Recycling and Disposal In the U.S. and Canada, Motorola Solutions participates in the nationwide Call2Recycle program for battery collection and recycling. Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, go to http://www.call2recycle.org/ or call 1-800-8-

BATTERY. This website and telephone number also provide other useful information concerning recycling options for consumers, businesses, and governmental agencies. 1.4 Additional Performance Enhancement The following performance enhancements are some of the latest creations designed to enhance the security, quality, and efficiency of the radios. 1.4.1 ASTRO 25 Enhanced Data ASTRO 25 Enhanced Data is optimized to handle different message sizes and variable update rates from different applications of the radio. To improve data channel efficiency and enable denser network traffic, add Enhanced Data to the Integrated Data system with a software installation. 1.4.2 Dynamic System Resilience Dynamic System Resilience (DSR) ensures that the radio system is seamlessly switched to a backup master site dynamically during a system failure. DSR also provides indications such as failure detection, fault recovery, and redundancy within the system. DSR also supports mechanisms related to the Integrated Voice and Data (IV&D) or data centric. 13 MN006727A01-AA Read Me First 1.4.3 CrossTalk Prevention 1.4.4 Encrypted Integrated Data 1.4.5 SecureNet CrossTalk Prevention feature prevents crosstalk scenarios and allows the adjustment of the internal SSI clock rate of the radio. This reduces the possibility of radio frequency interfering spurs. Encrypted Integrated Data (EID) provides security encryption and authentication of Integrated Voice and Data (IV&D) data bearer service communication between the radio and the Customer Enterprise Network. SecureNet allows you to perform secured communications on an Analog or Motorola Data Communication (MDC) channel. The MDC Over-the-Air Rekeying (OTAR) feature allows you to perform OTAR activities on an MDC channel. 1.4.6 P25 Digital Vehicular Repeater System Motorola Solutions offers an MSI Certified APX compatible, third party, P25 Digital Vehicular Repeater System (DVRS) that provides low-cost portable radio coverage in areas where only mobile radio coverage is available and portable radio coverage is either intermittent or non-existent. NOTICE: Portable subscriber units enabled in the system for Radio Authentication shall be able to authenticate regardless of whether they are communicating directly on the system or by using a DVRS. 1.4.7 Conventional Talkgroup and Radio Scan Enhancements Enhancements have been made to the Conventional Talkgroup at the system to improve the Scan feature operation significantly when multiple agencies are using a single conventional radio frequency channel. These enhancements allow you to use Selective Squelch to operate on only the subset of talkgroups that are relevant to the users rather than all talkgroups on the channel. The enhancements support the following Scan mode:

Mixed Vote Scan. Standard Conventional Scan. Priority Operation. Up to 30 different talkgroups can be supported using conventional channels. A maximum of four talkgroups can be supported when Vote Scan channels are being used. Smart PTT is supported with this enhancement as Smart PTT prevents you from transmitting while other users are on the channel. NOTICE: User Selectable Talkgroups are not compatible with this Conventional Talkgroup Enhancement. 14 MN006727A01-AA Read Me First 1.5 What Your Dealer/System Administrator Can Tell You If the radio is to be operated in extreme temperatures (less than -30 C or more than +60 C), check with your system administrator for the correct radio settings. You can consult your dealer or system administrator about the following:

Is your radio programmed with any preset conventional channels?

Which buttons have been programmed to access other features?

What optional accessories may suit your needs?

NOTICE: Specifications may vary for different radio models. Contact your system administrator for more information. 15 MN006727A01-AA Preparing Your Radio for Use Preparing Your Radio for Use This section provides simple instructions to prepare your radio for use. 2.1 Charging the Battery Prerequisites:

WARNING: To avoid a possible explosion:

Do not replace the battery in any area labeled hazardous atmosphere. Do not discard batteries in a fire. When and where to use: The Motorola Solutions-approved battery shipped with your radio is uncharged. Prior to using a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and performance. For a list of Motorola Solutions-authorized batteries and chargers available for use with your radio, see Accessories on page 76. NOTICE: When charging a battery attached to a radio, the radio must be turned off. Procedure:

To charge the battery, place the battery (with or without the radio) in a Motorola Solutions-

approved charger. The LED on the charger indicates the charging progress; see the Charger User Guide. 2.2 Attaching the Battery Prerequisites: If your radio is preprogrammed with volatile-key retention, the encryption keys are retained for approximately 30 seconds after battery removal. Check with your dealer or system administrator for more information. When and where to use:

NOTICE:

User is notified if radio detects non-Motorola Solutions battery upon powering up, charging, or removing from the charger. This feature is applicable for IMPRES and Non-IMPRES battery. When the radio is attached with the non-Motorola Solutions battery, a tone sounds, display shows Unknown Battery temporarily, and battery indicator is not shown in the radio display. Battery menu screen displays Unknown Battery permanently and IMPRES battery information is not shown on the radio display. Procedure:

1 Slide the battery into the radio frame until the side latches click into place. 16 2 To remove the battery, turn the radio off. Squeeze the release latches at the bottom of the battery until the battery releases from the radio and remove the battery from the radio. 2.3 Attaching the Antenna Prerequisites: Ensure the radio is turned off before attaching the antenna. Procedure:

1 Set the antenna in the receptacle. 2 Turn the antenna clockwise to attach to the radio. MN006727A01-AA Preparing Your Radio for Use 17 A MN006727A01-AA Preparing Your Radio for Use 3 To remove the antenna, turn the antenna counterclockwise. NOTICE: When removing the antenna, ensure that the radio is turned off. 2.4 Removing and Attaching the Accessory Connector Cover When and where to use: The accessory connector is on the antenna side of the radio. It is used to connect accessories to the radio. NOTICE: To prevent damage to the connector, shield it with the connector cover when not in use. Procedure:

1 To remove the accessory connector cover, rotate the thumbscrew counterclockwise until it disengages from the radio. NOTICE: If the thumbscrew is too tight, use an Allen wrench at to loosen it first. 2 Rotate and lift the connector cover to disengage it from the radio. 3 To attach the accessory connector cover, insert the hooked end of the cover into the slot above the connector. 4 Press the top of the cover downward to seat it in the slot. 5 Once in place, tighten by rotating the thumbscrew clockwise by hand. 18 A C B MN006727A01-AA Preparing Your Radio for Use 2.5 Using the Carry Holder Procedure:

1 Position the radio within the carry holder with the main speaker facing outward. 2 Slide the radio down into the carry holder until it clicks in place. 3 To remove the radio from the carry holder, place the tip of your fingers on the ledge of the carry holder. 19 MN006727A01-AA Preparing Your Radio for Use 4 Push at the bottom of the radio until the radio is released from it. 2.6 Attaching the Belt Clip Procedure:

to attach the belt clip. 1 Align the grooves of the belt clip with those of the radio and press upward until you hear a click 20 2 Use a flat-bladed object to press the belt clip tab away from the radio. Then, slide the clip downward and away from the radio to remove the clip. MN006727A01-AA Preparing Your Radio for Use 2.7 Turning On the Radio Procedure:

1 Rotate the On/Off/Volume Control Knob clockwise until you hear a click. If the power-up test is successful, you see a splash screen on the radio display, followed by the Home screen and the Codeplug Alias. If the power-up test is unsuccessful, you see Error XX/YY (XX/YY is an alphanumeric code). NOTICE:

If the radio fails to power-up after repeating a few times, record the Error XX/YY code and contact your dealer. Codeplug Alias feature is enabled through Customer Programming Software (CPS) configuration to display the codeplug alias as a temporary text during power on. 2 To turn off the radio, rotate the On/Off/Volume Control Knob counterclockwise until you hear a click. 21 MN006727A01-AA Preparing Your Radio for Use 2.8 Adjusting the Volume Prerequisites: Ensure the radio is powered on and the main speaker is pointed towards you for increased loudness and intelligibility, especially in areas with loud background noises. Procedure:

1 To increase the volume, rotate the On/Off/Volume Control Knob clockwise. 2 To decrease the volume, rotate this knob counterclockwise. 22 A MN006727A01-AA Radio Controls Radio Controls This chapter explains the buttons and functions to control the radio. 3.1 Radio Parts and Controls No. Description Antenna Top (Orange) Button Accessory Connector 16-Position Select Knob This button is usually programmed as the Emergency button. This knob is usually programmed for channel selection. On/Off/Volume Control Knob Rotate clockwise until you hear a click to turn on the radio. Rotate counterclockwise until you hear a click to turn off the radio. Rotate clockwise to increase the volume. Rotate counterclockwise to decrease the volume. 3-Position A/B/C Switch This switch is usually programmed for zone selection. Belt Clip 1 2*

3 4*

5 6*

7

* These radio controls/buttons are programmable. 23 1 2 3 4 5 6 7 8 9 10 11 12 13 16 14 15 17 18 MN006727A01-AA Radio Controls Description Battery Latch 2-Position Concentric Switch This switch is usually programmed to enable or disable secure operation. Purple (Side Top) Programmable Button Use this programmable button to access a preprogrammed function or enable or disable a feature. Push-to-Talk (PTT) Button Press and hold to talk in simplex calls or to initiate a group call, release it to listen. Middle Side (1-Dot) Programmable Feature Button Use this programmable button to access a preprogrammed function or enable or disable a feature. Lower Side (2-Dot) Programmable Feature Button Use this programmable button to access a preprogrammed function or enable or disable a feature. Your system administrator can program the programmable buttons as shortcuts to radio functions or preset channels/groups depending on the duration of a button press. Some functions can also be programmed to the radio switches. Top Display Microphone Speaker Battery Bluetooth Pairing Location Indicator 3.2 Programmable Features 3.2.1 Assignable Radio Functions Bluetooth On/Off Allows you to turn on/off the Bluetooth. Bluetooth Audio Reroute Bluetooth Headset PTT Keys up the Bluetooth Headset microphone. Bluetooth Clear All Pairing Bluetooth Inquiry On/Off Enables the Bluetooth Search feature. Bluetooth Discoverable On/Off Allows you to toggle the audio route between the radio speaker or Remote Speaker Microphone and the Bluetooth headset. Allows you to clear all pairing information for Bluetooth by pressing and holding the Bluetooth On/Off Button. Enables Bluetooth visibility pressing and holding the Bluetooth Inquiry On/Off Button. No. 8 9*

10*

11 12*

13*

14 15 16 17 18 24 MN006727A01-AA Radio Controls Call Response Allows you to answer a private call. Dynamic Priority (Conventional Only) Allows any channel in a Scan List (except for the Priority-One channel) to temporarily replace the Priority-Two channel. Depending on the programming, initiates or cancels an emergency alarm or call. Displays the Internet Protocol (IP) address, device name, and status of the radio. Emergency Internet Protocol Address Man Down Clear Clears the Man Down mode alarm that is triggered when your radio achieves or passes a tilt angle threshold or a combination of the angle threshold and a motion sensitivity level. Monitor (Conventional Only) Monitors a selected channel for all radio traffic until the function is disabled. Nuisance Delete Temporarily removes an unwanted channel, except for priority channels or the designated transmit channel from the scan list. Private Line Defeat (Conventional Only) Overrides any coded squelch (DPL or PL) that is preprogrammed to a channel. Priority Dispatch Rekey Request Allows you to call the dispatcher on a different talkgroup. Notifies the dispatcher that a new encryption key is needed. Repeater Access Button (RAB) (Conventional Only) Allows you to manually send a repeater access codeword. Reprogram Request (Trunking Only) Notifies the dispatcher that a new dynamic regrouping assignment is needed. Request-To-Talk (Conventional Only) Notifies the dispatcher that you want to send a voice call. Scan Toggles scan on or off. Scan List Programming Selects the scan list for editing (by pressing and holding the Scan button). Secure Transmission Select (Conventional and Trunking) Toggles the Secure Transmission On or Off when the Secure/Clear Strapping field is set to Select for the current channel and when the radio is model/option capable. Site Display/Search (Trunking Only) Displays the current site ID and RSSI value; performs site search for Automatic Multiple Site Select

(AMSS) or SmartZone operation. Site Lock/Unlock (Trunking Only) Locks onto a specific site. Talkaround/Direct (Conventional Only) Basic Zone Bank Toggles between using a repeater or communicating directly with another radio. Provides access from up to six zones by toggling between two banks of three zones, one group of three (A, B, and C) to a second group of three zones (D, E, and F). 25 Provides access from up to 75 zones by toggling between 25 banks (A, B, ... X or Y) of three zones. MN006727A01-AA Radio Controls Enhanced Zone Bank Wi-Fi Toggles Wi-Fi on or off. Controls Lock Light/Flip TX Power Level Voice Announcement Voice Mute Volume Set Tone Sets the volume set tone. 3.2.2 Assignable Settings or Utility Functions Locks or unlocks the programmable buttons, switches, or rotary knobs. Press the button to toggle the display backlight on and off; press and hold the button to reverse the content of the top display. Toggles the transmit power level between high and low. Audibly indicates the current feature mode, zone, or channel that you have been assigned to. Toggles the voice transmission between mute and unmute. 26 MN006727A01-AA Status Indicators Status Indicators This section explains the status indicators of the radio. 4.1 Battery Charge Status Your radio indicates the battery charge status through LED, sounds, and the fuel gauge icon on the display. You can also check the battery charge status by using the menu entry. If you press the PTT button when your battery is low, the LED blinks red and you hear a short, high-

pitched tone. 4.1.1 Fuel Gauge Icons Gauge The fuel gauge icon indicates the battery level of your radio. Battery Charge 76% to 100% full 51% to 75%

26% to 50%

11% to 25%

10% or less (at 10%, the gauge begins blinking) 4.1.2 HAZLOC Battery Type Detection This feature alerts the user when there is a HAZLOC certification mismatch between the radio and the battery. This feature supports IMPRES batteries only. During power-up, if there is a mismatch, the following scenarios occurs:

The radio continuously displays Wrong Battery with red intelligent backlight The radio Voice Announcement announces the preprogrammed Wrong Battery The battery icon blinks continuously A repetitive tone sounds LED blinks RED continuously 27 MN006727A01-AA Status Indicators NOTICE:

The radio alerts you when NNTN8921 and NNTN8930 batteries are attached to the radio. These batteries are not supported by the radio. The radio requires a HAZLOC-certified and compatible battery by default. The radio does not display any indication when the radio is connected to the charger or when the radio and battery is UL certified. The radio alerts the user when the battery is not UL certified with the radio. Refer to the radio UL Manual for a list of battery which is UL certified with the radio. Check with your dealer or system administrator for more information. The Status LED shows the operational status of your radio. 4.2 LED Indications Table 1: LED Indications Indication Solid red Blinking red Status Radio is transmitting. Radio is transmitting at low battery condition or detects an incompatible battery. Double blinking red Radio is transmitting an emergency alarm or call. Rapid blinking red Radio has failed the self-test upon powering up or encountered a fatal er-

ror. Solid yellow Channel is busy in conventional mode. Blinking yellow Radio is receiving a secured transmission. Solid green Blinking green Radio is powering up or is on a non-priority channel while in the Scan List Programming mode. Radio is receiving an individual or telephone call or is on a Priority-Two channel while in the Scan List Programming mode. Rapid blinking green Radio is on a Priority-One channel while in the Scan List Programming mode. 4.3 Status Icons Selected icons are also shown on the first row of the 112 x 32 pixel top monochrome display screen of your radio. Icon Description Radio is receiving a call or data. Radio is transmitting a call or data. 28 Icon Description MN006727A01-AA Status Indicators or For IMPRES battery operation only the icon shown indicates the charge remaining in the battery. For all battery operation the icon blinks when the battery is low. The number of bars displayed represents the received signal strength for the current site (trunking only). The more stripes in the icon, the stronger the signal. The radio has roamed to and is currently registered to a foreign system. Direct On Off Radio is configured for direct radio-to-radio communication

(during conventional operation only). Radio is connected with other radios through a repeater. Selected channel is being monitored (during conventional opera-

tion only). When the radio displays L, the radio is set at Low power. When the radio displays H, the radio is set at High power. Radio detects activity on channel designated as Priority-One. Radio detects activity on channel designated as Priority-Two. Radio is in the view or program mode. Radio is scanning a scan list. Blinking dot Steady dot On steady View mode Blinking Program mode Basic Zone Bank 1 A B C Radio is in Zone 1. Radio is in Zone 2. Radio is in Zone 3. The vote scan feature is enabled. 29 MN006727A01-AA Status Indicators Icon until or 30 Description Basic Zone Bank 2 Radio is in Zone 4. Radio is in Zone 5. Radio is in Zone 6. Enhanced Zone Bank D E F A B C X Y until On Off On Blinking Steady Blinking On Inverted Contains Zone 1, Zone 2, and Zone 3, Contains Zone 4, Zone 5, and Zone 6, Contains Zone 7, Zone 8, and Zone 9, Contains Zone 70, Zone 71, and Zone 72, Contains Zone 73, Zone 74, and Zone 75. Secure operation. Clear operation. Blinking Receiving an encrypted voice call. Feature is enabled and GPS signal is available. Feature is enabled, but no GPS signal is available. Bluetooth is on and ready for Bluetooth connection. Bluetooth is connected to the external Bluetooth device. Bluetooth device is disconnected. The current channel supports SmartConnect. The current channel is connected through the SmartConnect feature. MN006727A01-AA Status Indicators 4.4 Intelligent Lighting Indicators This feature temporarily changes the backlight of the top display screen to help signal that a radio event has occurred. This feature temporarily changes the display backlight color and the alert text background color of the radio to help signal that a radio event has occurred. Backlight and Bar Color Notification When Orange Emergency Alerts The radio initiates an emergency alarm or call. The radio receives an emergency alarm or call. Red Critical Alerts The radio battery is low. Green Call Alerts The radio receives a private call. The radio is out of range. The radio enters Failsoft mode. The radio is unable to establish a full connection with the system. The radio is unable to authenticate or register with the system. The radio detects mismatch between the radio and the battery. The radio receives a phone call. The radio receives a call alert. The radio receives a selective call. The radio enters Geofence. 4.5 Alert Tones Your radio uses alert tones to inform you of the condition of your radio. The following table lists these tones and when they occur. You Hear Tone Name Heard Short, Low-

Pitched Tone Radio Self Test Fail When radio fails its power-up self test. Reject When an unauthorized request is made. Time-Out Timer Warn-

ing Four seconds before time out. No ACK Received When radio fails to receive an acknowledgment. Individual Call Warn-

ing Tone When radio is in an individual call for greater than six seconds without any activity. Man Down Entry When radio initiates Man Down mode. Long, Low-

Pitched Tone Time-Out Timer Timed Out After time out. 31 MN006727A01-AA Status Indicators You Hear Tone Name Heard Talk Prohibit/PTT In-

hibit

(When PTT button is pressed) transmissions are not al-

lowed. Lack of Voice PTT Time out When the radio ends your call after it detected there are lack of voice for five seconds after the PTT is pressed and hold. Your radio ends the call to enable your radio to receive calls from other radio users. Out of Range

(When PTT button is pressed) the radio is out of range of the system. Invalid Mode When radio is on an unpreprogrammed channel. Busy When system is busy. Valid Key-Press When a correct key is pressed. Radio Self Test Pass When radio passes its power-up self test. Clear Voice At beginning of a non-coded communication. When activity on a priority channel is received. Priority Channel Re-

ceived Emergency Alarm/Call Entry Central Echo When entering the emergency state. When central controller has received a request from a radio. Volume Set When volume is changed on a quiet channel. Emergency Exit When exiting the emergency state. Failsoft When the trunking system fails. Automatic Call Back When voice channel is available from previous request. Keyfail When encryption key has been lost. Console Acknowledge When status, emergency alarm, or reprogram request Received Individual Call ACK is received. When Call Alert or Private Call is received. Site Trunking When a SmartZone trunking system fails. Over-the-Air Program-

ming request When the radio receives an over-the-air programming request. Low-Battery Chirp When battery is below preset threshold value. GPS Fails When the GPS fails or loses signal. Ringing Phone Call Received When a land-to-mobile phone call is received. A Group of Low-Pitch-

ed Tones Short, Me-

dium-Pitch-

ed Tone Long, Medi-

um-Pitched Tone A Group of Medium-

Pitched Tones Two Short, Medium-

Pitched Tones Short, High-

Pitched Tone

(Chirp) Two High-

Pitched Tones 32 MN006727A01-AA Status Indicators You Hear Tone Name Heard Gurgle Dynamic Regrouping Talk Permit

(When PTT button is pressed) a dynamic ID has been received.

(When PTT button is pressed) is verifying with the sys-

tem for accepting its transmissions. New Message When a new message is received. Unique, Low-Pitch-

ed Chirp Unique, High-Pitch-

ed Chirp Incremen-

tal- Pitched Tone Decremen-

tal- Pitched Tone A Group of Very High-

Pitched Tones Unique Low-High Tone Unique High-Low Tone Priority Status When a priority message is received. Bluetooth Paired When Bluetooth accessory is paired with the radio. Bluetooth Connected When Bluetooth accessory is connected to the radio. Bluetooth Unpaired When Bluetooth accessory is unpaired from the radio. Bluetooth Disconnect-

ed When Bluetooth accessory is disconnected from the ra-

dio. Man Down Continu-

ous Tone Critical Man Down Continuous Tone When radio is in Man Down mode and prepares to transmit Emergency Alarm when the timer of this alarm ends. When radio is in Man Down Enhanced mode and pre-

pares to transmit Emergency Alarm when the timer of this alarm ends. Enhanced Zone Bank Up When EZB Up button is pressed to scroll the Enhance Zone Bank up. Enhanced Zone Bank Down When EZB Down button is pressed to scroll the En-

hance Zone Bank down. 4.6 Display Color Change On Channel This feature provides visual channel identification for users to have a quick visual recognition on a particular channel. Your radio must be preprogrammed to allow you to use this feature. When changing channels, the radio backlight on top display and accessories (DRSM or keypad Mic) changes to the preprogrammed color. When changing channels, the radio backlight on top display and accessories (DRSM) changes to the preprogrammed color. The radio backlight on top display changes to white and if connected to accessories, the DRSM backlight changes to white and the keypad mic backlight changes to green for the following scenarios:

The backlight on top display changes to white and if connected to DRSM, the DRSM backlight changes to white for the following scenarios:

When changing to or powering up on invalid channels such as unprogrammed channels, receiver frequency error channel and blank channels 33 MN006727A01-AA Status Indicators For hard key zeroize, key loading, and scan list programming, the backlight follows the home channel backlight color. 34 MN006727A01-AA General Radio Operation General Radio Operation This chapter explains the general operations of your radio. 5.1 Selecting a Zone When and where to use: A zone is a group of channels. Procedure:

zone. Select a zone using the preprogrammed Zone (3-Position A/B/C) switch:

a. Move the preprogrammed Zone (3-Position A/B/C) switch to the position of the required If the zone number entered is unprogrammed, the display shows INVALID. Repeat this step. 5.2 Selecting a Radio Channel When and where to use: A channel is a group of radio characteristics, such as transmit/receive frequency pairs. Procedure:

Select a channel using the preprogrammed 16Position Select Knob to the desired channel. a. Rotate the preprogrammed 16Position Select Knob to the desired channel. 5.3 Receiving and Responding to a Radio Call Once you have selected the required channel and/or zone, you can proceed to receive and respond to calls. The radio shows different indicators based on the system the radio is configured. The LED lights up solid red while the radio is transmitting. In conventional mode, the LED lights up solid yellow when the radio is receiving a transmission. In trunking mode, there is no LED indication when the radio receives a transmission. If the radio is receiving a secure transmission, the LED blinks yellow. 5.3.1 Receiving and Responding to a Talkgroup Call When and where to use: When you receive a talkgroup call (while on the Home screen) the radio displays the following depending on the system your radio is configured to:

For ASTRO Conventional system, the LED lights up solid yellow. The display shows the talkgroup alias or ID, and the caller alias or ID. 35 MN006727A01-AA General Radio Operation Procedure:

For Trunking system, the display shows the caller alias or ID. 1 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 2 Press the PTT button to respond to the call. The LED lights up solid red. 3 Release the PTT button to listen. 5.3.2 Receiving and Responding to a Private Call (Trunking Only) A Private Call is a call from one individual radio to another. Other users in the current talkgroup cannot hear the one-to-one call between the two radios. The calling radio automatically verifies that the receiving radio is active on the system and can display the caller ID. When and where to use:

When you receive a Private Call, you hear two alert tones and the LED blinks green. The display shows CALL RCV, alternating with the caller alias (name) or ID (number). Procedure:

1 Press the Call Response button within 20 seconds after the call indicators begin. 2 Press and hold the PTT button to talk. Release the PTT button to listen. 3 Press the Call Response button to hang up and return to the Home screen. 5.3.3 Receiving and Responding to a Telephone Call (Trunking Only) This feature allows you to receive calls similar to standard phone calls from a landline phone. When and where to use:

When you receive a Telephone Call, you hear a telephone-type ringing and the LED blinks green. The backlight of the screen turns green and the display shows PHN CALL and the call received icon blinks. Procedure:

1 Press the Call Response button within 20 seconds after the call indicators begin. 2 Press and hold the PTT button to talk. Release the PTT button to listen. 3 Press the Call Response button to hang up and return to the Home screen. 5.4 Methods to Make a Radio Call You can select a zone, channel, subscriber ID, or talkgroup by using:

The preprogrammed Zone switch. The 16-Position Select Channel Knob. A preprogrammed button. 36 MN006727A01-AA General Radio Operation 5.4.1 Making a Talkgroup Call Procedure:

1 Turn the 16-Position Select Channel Knob to select the channel with the desired talkgroup. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to make the call. The radio shows different indicators based on the system the radio is configured. For ASTRO Conventional system, the LED lights up solid red. The display shows the talkgroup alias or ID. For Trunking system, the LED lights up solid red. 4 Speak clearly into the microphone. 5 Release the PTT button to listen. 5.4.2 Making a Private Call (Trunking Only) Procedure:

1 Press the preprogrammed Private Call button to dial the preprogrammed ID. The display shows the preprogrammed ID. 2 Press the PTT button to initiate the Private Call. 3 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. When you are connected, the display shows the ID of the target radio. If no acknowledgment is received, the display shows NO ACK. 4 Press and hold the PTT button to talk. Release the PTT button to listen. 5 Press the preprogrammed Private Call button to return to the home screen. 5.4.3 Making an Enhanced Private Call (Trunking Only) Prerequisites: Your radio must be preprogrammed to allow you to use this feature. Procedure:

1 Press the preprogrammed Quick Access (One-Touch) Private Call button to dial the preprogrammed ID and initiate the Enhanced Private Call. The display shows the preprogrammed ID and a ringing tone sounds. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. When you are connected, the display shows the ID of the target radio and the ringing tone stops. If no acknowledgment is received, the display shows NO ACK. 37 MN006727A01-AA General Radio Operation If the target radio does not respond before the time out, the display shows NO ANSR. 3 Press and hold the PTT button to talk. Release the PTT button to listen. 4 Press the preprogrammed Private Call button to return to the home screen. 5.5 Switching Between Repeater or Direct Operation Button The Repeater Operation increases the radio coverage area by connecting with other radios through a repeater. The transmit and receive frequencies are different. The Direct or talkaround operation allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same. Press the preprogrammed Repeater/Direct switch to toggle between talkaround and repeater modes. The monitor feature ensures that a channel is clear before transmitting. The lack of static on a digital channel when the users switch from analog to digital radios is not an indication that the radio is malfunctioning. Digital technology quiets the transmission by removing the noise from the signal and allows only the clear voice or data information to be heard. Procedure:

5.6 Monitor Feature 5.6.1 Monitoring a Channel Procedure:

Monitoring a Channel using the Monitor and Volume Set button. a. Press the preprogrammed Monitor button. The Carrier Squelch indicator appears on the display when you monitor a channel using the preprogrammed Monitor button. b. Press and hold the Volume Set button to hear the volume set tone. c. Adjust the Volume Control Knob if necessary. d. Release the Volume Set button. e. Press and hold the PTT button to transmit. The LED lights up solid red. f. Release the PTT button to receive (listen). 38 MN006727A01-AA General Radio Operation 5.6.2 Monitoring Conventional Mode This feature allows you to monitor channel traffic on conventional channels by defeating the coded squelch. Thus, you can listen to another active user on the channel. This way, you may be prevented from taking over the conversation of another user. When and where to use: Your radio may be preprogrammed to receive Private-Line (PL) calls. Procedure:

1 Momentarily press the Monitor button to listen for activity. The Carrier Squelch indicator appears on the display. 2 Press and hold the Monitor button to set continuous monitor operation. The duration of the button press is programmable. 3 Press the Monitor button again, or the PTT button, to return to the original squelch setting. If you try to transmit on a receive-only channel, you hear an invalid tone until you release the PTT button. 39 MN006727A01-AA Advanced Features Advanced Features This chapter explains the operations of the features available in your radio. 6.1 Advanced Call Features This chapter explains the operations of the call features available in your radio. 6.1.1 Selective Call (ASTRO Conventional Only) This feature allows you to receive a call from a specific individual with privacy. 6.1.1.1 Receiving a Selective Call When and where to use: When you receive a Selective Call, you hear two alert tones and the LED lights up solid yellow. The backlight of the screen turns green momentarily, the display briefly shows CALL RCV, and the speaker unmutes. Procedure:

1 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 2 Press and hold the PTT button to talk. Release the PTT button to listen. 6.1.1.2 Making a Selective Call Procedure:

Prerequisites: Your radio must be preprogrammed for you to use this feature. 1 Press the preprogrammed Selective Call button to dial the preprogrammed ID. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press and hold the PTT button to start the Selective Call. The display shows the current zone and channel name. 4 Release the PTT button to listen. The radio returns to home screen. Repeat step 1 to step 3 to start the Selective Call. 6.1.2 Making a Priority Dispatch Calls If a talkgroup is congested, the Priority Dispatch feature allows you to call the dispatcher on a different talkgroup. This talkgroup is called the Priority Talkgroup. Each trunking talkgroup can have its own 40 MN006727A01-AA Advanced Features assigned Priority Talkgroup.Priority Dispatch is not available during Emergency operations. Scan feature is suspended when Priority Dispatch is initiated. Prerequisites: Dispatch console that supports this feature must be preprogrammed to use this feature. Check with your dealer or system administrator for more information on dispatch console supporting this feature. Procedure:

1 Press the preprogrammed Priority Dispatch button. A tone sounds and the radio enters Priority Dispatch mode. The radio exits this mode when the Priority Dispatch Time Out Timer expires. 2 Before the Priority Dispatch Time Out Timer expires, press and hold the PTT button to transmit. The display shows the Priority Talkgroup alias. 3 Release the PTT button to listen. The radio exits Priority Dispatch mode, returns to its original talkgroup, and displays the home channel alias. 6.1.3 Dynamic Regrouping (Trunking Only) This feature allows the dispatcher to temporarily reassign selected radios to a particular channel to communicate with each other. When your radio is dynamically regrouped, it receives a dynamic regrouping command and automatically switches to the dynamically regrouped channel. You hear a tone and the display shows the name of the dynamically regrouped channel. When the dispatcher cancels dynamic regrouping, the radio automatically returns to the previous zone and channel. If you access a zone or channel that has been reserved as a dynamically regrouped mode for other users, you hear an invalid tone. 6.1.3.1 Classification of Regrouped Radios The dispatcher can classify regrouped radios into Select Enabled or Select Disabled categories. Select Enabled Select Disabled Select-enabled radios are free to change to any available channel, including the dynamic-

regrouping channel, once you have selected the dynamic-regrouping position. Select-disabled radios cannot change channels while dynamically regrouped. The radio is forced to remain on the dynamic-regrouping channel. The Scan and Private Call features are unavailable when your radio is Select Disabled. 41 6.1.3.2 Requesting a Reprogram (Trunking Only) This feature allows you to notify the dispatcher when you want a new dynamic regrouping assignment. Press the preprogrammed Reprogram Request button to send reprogram request to the dispatcher. The display shows RPGM and PLS WAIT. If you hear five beeps, the dispatcher has acknowledged the reprogram request. The display shows ACK RCVD and the radio returns to the Home screen. If the dispatcher does not acknowledge the reprogram request within six seconds, you hear a low-

pitched alert tone and the display shows NO ACK. MN006727A01-AA Advanced Features Procedure:

6.2 Scan Lists Scan lists are created and assigned to individual channels/groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group. Your radio supports different types of Scan Lists:

Trunking Priority Monitor Scan List Conventional Scan List Talkgroup Scan List Refer to a qualified radio technician for the maximum number of Scan Lists to be preprogrammed in your radio. 6.2.1 Intelligent Priority Scan Intelligent Priority Scan feature allows you to add or delete conventional channels and trunking talkgroups from multiple system into the priority scan lists. When the radio locks onto a channel in the Intelligent Priority Scan list, radio scans for higher priority member within the same Trunking or Conventional system. 6.2.2 Viewing a Scan List Procedure:

Turn the 16-Position Select Knob to view the members on the list. 6.2.3 Viewing and Changing the Priority Status Press the Top Side (Select) button to change the priority status of the currently displayed channel or the scan list status icon of the currently displayed channel. The radio shows one of following priority status icons and scenarios:

Procedure:

42 MN006727A01-AA Advanced Features A Scan icon indicates that the current channel is in the scan list as a non-priority channel. The LED lights up solid green. A Priority-One Channel Scan icon indicates that the current channel is in the scan list as the Priority-One channel. The LED rapidly blinks green. You hear all traffic on the Priority-

One channel, regardless of traffic on non-priority channels. A Priority-Two Channel Scan icon indicates that the current channel is in the scan list as the Priority-Two channel. The LED blinks green. No icon indicates that the current channel is deleted from the scan list. This feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels. Scanning is halted if you initiate a call and resumes when the call has ended. 6.3 Scan 6.3.1 Turning Scan On or Off Procedure:

Press the preprogrammed Scan button to toggle SCAN ON or SCAN OFF to initiate or stop scan. If the scan is enabled, the display shows SCAN ON and the scan status icon. If the scan is disabled, the display shows SCAN OFF. 6.3.2 Making a Dynamic Priority Change (Conventional Scan Only) When and where to use:

While the radio is scanning, the dynamic priority change feature allows you to temporarily change any channel in a scan list (except for the Priority-One channel) to the Priority-Two channel. This change remains in effect until scan is turned off. Scan then reverts to the default setting. Procedure:

Making a Dynamic Priority Change using the preprogrammed Dynamic Priority button:

a. When the radio locks onto the channel designated as the new Priority-Two channel, press the preprogrammed Dynamic Priority button. The radio continues scanning the remaining channels in the list. 6.3.3 Deleting a Nuisance Channel When and where to use:

If a channel continually generates unwanted calls or noise (termed nuisance channel), you can temporarily remove the unwanted channel from the scan list. This capability does not apply to priority channels or the designated transmit channel. 43 MN006727A01-AA Advanced Features Procedure:

NOTICE: Deleting a nuisance channel is only possible through the preprogrammed Nuisance Channel Delete button. When the radio is locked onto the channel to be deleted, press the preprogrammed Nuisance Delete button. The radio continues scanning the remaining channels in the list. 6.3.4 Restoring a Nuisance Channel Procedure:

To restore the deleted nuisance channel, perform one of the following actions:

Stop and restart a scan. Mode change to another channel and back to the original channel. Turn off the radio and then turn it on again. 6.4 Call Alert Paging This feature allows your radio to work like a pager. If other users are away from their radios or if they are unable to hear their radios, you can send them an individual call alert page. You can also verify if a radio is active on the system. Depending on how your radio is programmed, if there is no answer after the maximum ring time or when you press the PTT button for an Enhanced Private Call, the radio automatically sends a call alert page. NOTICE: This feature must be preprogrammed by a qualified radio technician. 6.4.1 Receiving a Call Alert Page When and where to use: When you receive a Call Alert page, you hear four repeating alert tones and the LED blinks green. The call received icons blinks and the display shows PAGE RCV. Procedure:

Press any button to clear the Call Alert page. 6.4.2 Sending a Call Alert Page When and where to use:

Your radio must be preprogrammed for you to use this feature. Procedure:

44 Press the preprogrammed Call Alert Paging button to send a page to the preprogrammed ID. If the call alert page is sent successfully, a tone sounds and the display shows the current zone and channel name. If the call alert page is not acknowledged, a tone sounds and the display shows the current zone and channel name. MN006727A01-AA Advanced Features The Emergency feature is used to indicate a critical situation. An emergency signal overrides any other communication over the selected channel. 6.5 Emergency Operation Your radio supports the following Emergency modes:

Emergency Alarm Emergency Call Emergency Alarm with Emergency Call Silent Emergency Alarm Only one Emergency mode can be assigned to the Emergency button. Your radio is also programmed to operate in one of the following conditions:

Tactical/Non-Revert The radio sends an emergency alarm and/or makes an emergency call on the current channel. Non-Tactical/Revert for Conventional System The radio reverts to the preprogrammed emergency channel to send an alarm and/or make an emergency call. Non-Tactical/Revert for Trunking System The radio reverts to the preprogrammed emergency talkgroup (trunking system) or channel

(conventional system) to send an alarm and/or make an emergency call. Man Down is an alternate way to activate the Emergency feature. For more information, see Man Down on page 52. Contact your system administrator for more information. 6.5.1 Special Considerations for Emergency Operation The following scenarios apply during Emergency operation:

Table 2: Emergency Operation Scenarios If... If you press the Emergency button while in a channel that has no Emergency capability, Then... a low-pitched tone sounds. If you change to a channel/mode with no Emer-

gency capability while in Emergency operation, the following occurs:

The display shows NO EMERG. A continuous low-pitched tone sounds until you select a valid Emergency channel/mode or until you disable the Emergency opera-

tion. 45 MN006727A01-AA Advanced Features If... Then... If you change to a channel/mode with Emergen-

cy capability while in Emergency operation, the Emergency Alarm and/or Emergency Call continues on the new channel/mode. If the radio is out-of-range of the system or the emergency alarm is not acknowledged, a tone sounds and the display shows No ac-

knowledge. 6.5.2 Emergency Keep-Alive This feature prevents the radio from being turned off when it is in Emergency mode. If this feature is enabled, you are required to exit Emergency mode before turning off your radio. 6.5.3 Exiting Emergency Operation If an Emergency operation is triggered on your radio, the dispatch console or radios configured as Supervisor can also exit the Emergency operation. Procedure:

To exit Emergency operation, press and hold the preprogrammed Emergency button. 6.5.4 Exiting Emergency as Supervisor (Trunking Only) Radios configured as Supervisor are able to cancel emergency mode of other radios. The dispatch console must be preprogrammed to use this feature. Check with your dealer or system administrator for more information on dispatch console supporting this feature. Procedure:

1 Perform one of the following actions:

If Then If the emergency mode is ini-

tiated by other radios, press and hold the Side Button 1 and press the Emer-

gency button. If the emergency mode is ini-

tiated by the Supervisor, Perform one of the following actions:

Press and hold the Emergency button. Press and hold the Side Button 1 and press the Emergency button. Wait for console to clear emergency. NOTICE: The following buttons combinations are supported:

Radio Side Button 1 and Top (Orange) button. Radio Side Button 1 and accessory Orange button. Accessory 1-Dot Button and radio Top (Orange) button. Accessory 1-Dot Button and accessory Orange button. 46 MN006727A01-AA Advanced Features 6.5.5 Sending an Emergency Alarm When and where to use: This feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher. NOTICE: The default timer of Emergency button press to activate Emergency is 1000 milliseconds. This timer is programmable from 506200 milliseconds by a qualified technician. Procedure:

Press the preprogrammed Emergency button. One of the following scenarios occurs:

The display shows EMERGENCY and the current zone or channel. You hear a short medium-

pitched tone and the LED blinks red momentarily. The radio sounds a short low-pitched tone to indicate that the selected channel does not support emergency and rejects to launch emergency mode. When you receive the dispatchers acknowledgment, the display shows ACK RCVD. Four tones sound, the alarm ends, and the radio exits the Emergency Alarm mode. If no acknowledgment is received, the display shows NO ACK. The alarm ends and the radio exits the Emergency Alarm mode. 6.5.6 Sending an Emergency Call (Trunking Only) When and where to use: This feature gives your radio priority access to a talkgroup. Procedure:

1 Press the preprogrammed Emergency button. One of the following scenarios occurs:

The display shows EMERGNCY and the current zone or channel. You hear a short medium-

pitched tone and the LED blinks red momentarily. You hear a short low-pitched tone to indicate that the selected channel does not support emergency and rejects to launch emergency mode. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press and hold the PTT button. Speak clearly into the microphone. 4 Release the PTT button to end the transmission and wait for a response from the dispatcher. 5 To exit Emergency Call, press and hold the preprogrammed Emergency button for about a second. 6.5.7 Sending An Emergency Call With Hot Mic (Trunking Only) This feature allows you to send an Emergency Call with hot mic to a group of radios. When and where to use:

Your radio must be programmed for this type of operation. 47 MN006727A01-AA Advanced Features Your radio microphone is automatically activated, allowing you to communicate with the group of radios without pressing the PTT button. This activated microphone state is also known as hot mic. The hot mic applies to the first voice transmission from your radio during the Emergency call. For subsequent transmissions in the same Emergency call, you must press the PTT button. Follow the procedure to send Emergency Call with hot mic on your radio. Procedure:

1 Press the preprogrammed Emergency button. One of the following scenarios occurs:

The display shows EMERGNCY and the current zone or channel. A tone sounds and the LED blinks red momentarily. to launch emergency mode. A tone sounds to indicate that the selected channel does not support emergency and rejects 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 The microphone remains active for the hot mic time specified in the radio's codeplug programming. 4 To exit Emergency Call, press and hold the preprogrammed Emergency button. 6.5.8 Sending an Emergency Alarm with Emergency Call When and where to use:

This feature gives your radio priority access on a channel for conventional system, and to a talkgroup for trunking system. Procedure:

1 Press the preprogrammed Emergency button. If successful, the display shows EMERGNCY on the current zone and channel. You hear a short, medium-pitched tone and the LED blinks red momentarily. The radio exits Emergency Alarm and enters the Emergency Call state when one of the following scenarios occur:

You receive the dispatcher acknowledgment. The display shows ACK RCVD. You receive no acknowledgment. The display shows NO ACK. You press the PTT button while in the Emergency Alarm mode. If unsuccessful, you hear the radio sounds a short low-pitched tone to indicate the selected channel does not support emergency and rejects to launch emergency mode. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press and hold the PTT button. Speak clearly into the microphone. 4 Release the PTT button to end the transmission and wait for a response from the dispatcher. 5 To exit Emergency Call, press and hold the preprogrammed Emergency button for about a second. Turning off the radio also cancels the emergency state. 48 MN006727A01-AA Advanced Features 6.5.9 Sending An Emergency Alarm and Call with Hot Mic This feature allows you to send an Emergency Alarm and Call with hot mic to a group of radios. When and where to use: Your radio must be programmed for this type of operation. Follow the procedure to send Emergency Alarms and Call with hot mic on your radio. Procedure:

1 Press the preprogrammed Emergency button. If successful, the display shows EMERGNCY on the current zone and channel. A tone sounds and the LED blinks red momentarily. The radio exits Emergency Alarm and enters the Emergency Call state when one of the following scenarios occur:

You receive the dispatcher acknowledgment. The display shows ACK RCVD. You receive no acknowledgment. The display shows NO ACK. If unsuccessful, a tone sounds to indicate that the selected channel does not support emergency and rejects to launch emergency mode. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 The microphone remains active for the hot mic time specified in your radio's codeplug programming. 4 To exit Emergency Call, press and hold the preprogrammed Emergency button. Turning off the radio also cancels the emergency state. 6.5.10 Sending a Silent Emergency Alarm When and where to use: This feature allows you to send an Emergency Alarm to the system without triggering any audio or visual indicators. Procedure:

1 Press the preprogrammed Emergency button. The display shows no changes, the LED does not light up, and you hear no tones. The silent emergency state continues until you perform the next step. Press and hold the preprogrammed Emergency button for about a second to exit the Silent Press and release the PTT button to exit the Silent Emergency Alarm mode and enter regular 2 Perform one of the following actions:

Emergency Alarm mode. dispatch or Emergency Call mode. 6.5.11 Emergency Find Me When the radio is in Emergency mode, the Emergency Find Me feature transmits Bluetooth Low Energy (BTLE) signals and other Emergency information to nearby radios. Contact your system administrator for more information. 49 6.5.11.1 Sending and Receiving Emergency Find Me Beacon Press the pre-programmed Emergency button to transmit the EFM beacon. The receiving radio displays BEAC RX. MN006727A01-AA Advanced Features Procedure:

6.6 Fireground The portable Fireground Communications System is designed for deployment at an incident scene. It consists of central components that provide on-scene and inbuilding radio coverage, and enhanced personnel accountability and monitoring:

Radio Frequency (RF) Modem (Conventional Only) Your APX portable radios Incident Management Software Command Terminal Control Channel Radio (Trunking) Optional Data Radio (Trunking) Accountability Server (Trunking) DVRS (Optional) Turning the radio on and off Automatic response to Polling Response to Evacuation commands Pressing the PTT button to make voice transmission Sending an Emergency Alarm and Call Entering or Exiting a Trunking Talkgroup If you have a critical situation, you can press the Emergency button which activates an alarm on the Incident Management Software at the command terminal. The command terminal receives the following status updates from your radio:

6.6.1 Entering Fireground Zone Channel (Conventional) Procedure:

1 Upon powering up, one of the following scenarios occurs:

If the Fireground Zone Channel is set as default, you hear the gurgle tone and the radio displays the home screen. You are in Fireground zone channel. If the Fireground Zone Channel is set as default, but you hear a short, low-pitched tone, the display shows REG FAIL to indicate that the command terminal does not respond to Fireground Zone Channel. Get a qualified technician for assistance. If your home channel is not Fireground Zone Channel, toggle or change the radio zone channel to Fireground Zone Channel. 50 MN006727A01-AA Advanced Features If you are entering Fireground Trunking Talkgroup, upon powering up, ensure that the Fireground Trunking Talkgroup is selected. The subscriber unit automatically appears on the Incident Commander's terminal. 2 Listen for a transmission. Adjust the Volume Control Knob if necessary. 3 Perform one of the following actions:

Press and hold the preprogrammed Volume Set button to hear the volume set tone. Adjust the Volume Control Knob if necessary. Release the Volume Set button. At the desired Fireground zone and channel, press the preprogrammed Monitor button and listen for activity. Adjust the Volume Control Knob if necessary. If your radio is working in Fireground Zone Channel, proceed to next step. 4 Press and hold the PTT button to transmit. The LED lights up solid red while transmitting. Talk into the microphone clearly if needed. 5 Release the PTT button to receive. You hear a Transmit End Tone. 6.6.2 Sending Evacuation Tone This feature enables the evacuation tone to be heard on the transmitting radio and on any radio that is able to receive the tone instruction. Procedure:

Press and hold the PTT button and then short press the Top (Orange) button. Once the tone begins to sound, if the orange button is released the tone continues to alarm on all radios within the talkgroup, until the PTT button is released. NOTICE: Radio does not transmit evacuation tone if the radio is in secure mode. 6.6.3 Responding to Evacuation Indicator When and where to use: The Incident Commander can trigger one of sixteen Tactical Alerts from the Command Terminal. These alerts can target individuals or groups of users within the Fireground Communication System. The ergonomic (visual and audible) response for the Tactical Alerts can be customized. Your radio sounds the audible response at the profile maximum alert tone volume level. The display shows the configurable programmed alert text and intelligent lighting. Procedure:

1 Perform one of the following actions:

Press the radio Top Side button. Press the RSM Side Button 1 if the radio is connected to RSM. Press the PTT button. PTT button must be configured in CPS to enable this function. The radio cancels the indications, a tone sounds and the radio sends an acknowledgment to the command terminal. NOTICE: Move the Volume Control Knob to adjust the volume of the audible alert from full volume. 51 MN006727A01-AA Advanced Features 6.7 Tactical Public Safety (Conventional Only) Tactical Public Safety (TPS) enables the member of a group to identify the start and the end of a transmission by displaying the caller name or ID on the radio display. 6.7.1 Using TPS Normal Transmission Procedure:

At TPS Zone Channel, perform one of the following actions:

Press PTT button to transmit. Talk clearly into the microphone. Release PTT button to listen. Receive and listen to call, the radio displays the callers name or ID. 6.7.2 Using TPS Emergency Transmission When and where to use:

The following are two important alert tones designed for this feature. Emergency Beacon During Emergency if the TPS radio user pushes the Emergency button, the radio sounds a Beacon at the maximum volume of the radio at radios internal speaker and it is not adjustable. This beacon goes to silent when user presses the PTT button for voice transmission. Emergency Call De-Key Sidetone The radio sounds an alert tone to remind radio user that the Emergency Mode is still active after user releases the PTT button for an Emergency call transmission. The volume of loudness depends on the maximum tone at your radio profile. Procedure:

1 Press the Emergency button to enter Emergency Mode. You hear the Emergency Beacon. 2 Press PTT button to make an Emergency Call. 3 Release to listen. You hear Emergency Call De-Key Sidetone. After a short pause, you hear Emergency Beacon. 4 Long press Emergency button to exit Emergency mode and cancel Emergency Beacon. Man Down is a supporting feature of the Emergency operation. The Emergency feature must be programmed for Man Down to operate. Your radio activates the Man Down feature when it achieves or exceeds a tilt angle threshold or a combination of the angle threshold and radio motion below the motion sensitivity level. The radio must stay in this condition for a programmed period before the Emergency Alarm or Call is activated. 6.8 Man Down 52 MN006727A01-AA Advanced Features NOTICE: Because Man Down may be triggered accidentally, consider the following scenarios when using your radio:

If the radio is programmed to a horizontal position only, it must be worn in a vertical position. If the radio is programmed with the Man Down feature, turn off the radio when charging it with a wall-mounted charger. 6.8.1 Radio Alerts When Man Down is Triggered When Man Down is triggered, your radio plays an alert tone and the display shows MAN-DOWN. NOTICE: If the radio is programmed for Surveillance Mode, it inhibits all tones and lights including the Man Down tones. Man Down Enhanced Your radio also supports Man Down Enhanced where it plays an alert tone for a preprogrammed period. This tone is louder than the preprogrammed minimum level or the current level of the speaker and it acts as a beacon that helps to find the radio. NOTICE: The radio plays this alert tone even in Surveillance Mode. When the alert tone is active, changing to another channel with a different setup triggers a different response from the radio:

The alert tone is inhibited when you change to a channel without Emergency feature. The alert tone is inhibited when you change to a channel with Emergency but no Man Down feature. configuration. The current alert tone is inhibited and is replaced with a different alert tone when you change to a channel with Emergency feature and a different Man Down configuration. The alert tone continues when you change to a channel with Emergency and similar Man Down 6.8.2 Testing the Man Down Feature Prerequisites: Ensure that Man Down is configured on your radio. Procedure:

1 Turn on the radio and place it in a vertical position for at least five seconds. 2 Lay the radio down in a horizontal position. The radio plays an alert tone and the display shows MAN-DOWN. Postrequisites: If Man Down is configured but the condition does not trigger the activation of the feature, send the radio to a qualified technician. 6.8.3 Exiting Man Down Procedure:

To exit Man Down mode, press Clr. 53 MN006727A01-AA Advanced Features 6.8.4 Re-Initiating Man Down Procedure:

Return the radio to a vertical position. If motion sensitivity is enabled, shake the radio. 6.9 Secure Operations To re-initiate Man Down after exiting Emergency Operation, perform one of the following actions:

Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels. By default, the radio automatically enters the encrypted environment without having to manually select or clear the secure transmission. 6.9.1 Selecting Secure Transmissions Procedure:

Turn the preprogrammed Secure/Clear switch to the secure position. If the selected channel is preprogrammed for clear-only operation, when you press the PTT button, you hear an invalid mode tone and the display shows CLR TX. The radio does not transmit until you set the Secure/Clear switch to the clear position. If the Ignore Secure/Clear Switch when Strapped programming option is enabled, the radio transmits without displaying any messages in the strapped mode of operation, regardless of the Secure/Clear switch setting. This option must be preprogrammed by a qualified radio technician. The Secure/Clear switch only applies when the radio is transmitting. 6.9.2 Selecting Clear Transmissions Procedure:

Turn the preprogrammed Secure/Clear switch to the clear position. If the selected channel is preprogrammed for secure-only operation, when you press the PTT button, you hear an invalid mode tone and the display shows SEC TX. The radio does not transmit until you set the Secure/ Clear switch to the secure position. You can request to configure the radio to ignore the clear voice or insecured transmission when the radio is in secured transmission. Check with your agent for details. If the Ignore Secure/Clear Switch when Strapped programming option is enabled, the radio transmits without displaying any messages in the strapped mode of operation, regardless of the Secure/Clear switch setting. This option must be preprogrammed by a qualified radio technician. The Secure/Clear switch only applies when the radio is transmitting. 54 MN006727A01-AA Advanced Features 6.9.3 Managing Encryption This chapter explains the encryption feature on your radio. 6.9.3.1 Loading Encryption Keys Prerequisites:

Procedure:

1 Attach the KVL to your radio. Refer to the Key Variable Loader (KVL) manual for equipment connections and setup. The display shows KEYLOAD and all other radio functions, except for power down, backlight, and volume, are locked out. NOTICE:

If the Multi-system Over-the-Air Rekeying feature is in use, the ASTRO profile name is displayed below KEYLOAD. 2 Select the required keys and press Load on the KVL. The KVL indicates that keyload is successful. 6.9.3.2 Multikey Feature This feature allows the radio to be equipped with different encryption keys and supports the DES-OFB algorithm. There are two types of encryption keys:

Conventional Multikey The encryption keys are strapped on a one-per-channel basis, through CPS. In addition, you can have operator-selectable keys, operator-selectable keysets, and operator-selectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups. Trunked Multikey If the radio is used for both conventional and trunked applications, strap the encryption keys for trunking on a per-talkgroup or announcement-group basis. In addition, a different key can be strapped to other features, such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operator-selectable key erasure. 6.9.3.3 Erasing Encryption Keys Procedure:

Erasing the single key in radios with the single-key option and erasing all keys in radios with the multikey option by using the preprogrammed Top Side (Select) button and Top (Orange) button:

a. Press and hold the Top Side (Select) button. b. While holding Top Side (Select) button down, press the Top (Orange) button. The display shows PLS WAIT. When all the encryption keys have been erased, the display shows ALL ERASED. 55 MN006727A01-AA Advanced Features NOTICE: Do not press the Top (Orange) button before pressing the Top Side

(Select) button, unless you are in an emergency situation as this sends an emergency alarm. 6.9.3.4 Requesting an Over-the-Air Rekey Prerequisites: Ensure that the Unique Key Encryption Key (UKEK) or Unique Shadow Key (USK) is loaded into the radio with the Key Variable Loader (KVL) before the rekey request can be sent. Refer to your local key management supervisor for more information. Procedure:

1 Press and hold the preprogrammed Rekey Request button to send the rekey request. If the rekey operation fails, a bad-key tone sounds and the display shows RKY FAIL. NOTICE: The rekey operation failure indicates that your radio does not contain the UKEK or USK. 6.9.3.5 MDC OTAR (Conventional Only) This feature allows you to view or define the Motorola Data Communications (MDC) Over-the-Air Rekeying (OTAR) features. It is applied only when operating in secure encrypted mode. In addition to Rekey Requests, OTAR transmissions include Delayed Acknowledgments, and Power-up Acknowledgments. Some of the selected options require configuration at the Key Management Controller (KMC) site to work properly. NOTICE: This feature must be preprogrammed by a qualified radio technician. Contact your system administrator for more information. 6.9.3.6 Infinite UKEK Retention This feature enables Unique Key Encryption Key (UKEK) to be permanently stored in the radio even when all the encryption keys are erased. Without this UKEK key, the radio cannot be rekeyed over the air. The Infinite UKEK Retention settings can be different for each secure profile. NOTICE: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. Hear-Clear is a noise reduction system which composed of Companding and Random FM Noise Canceller. Reduces the channel noise, such as OTA transmission that is predominantly present in UHF2 and 900 MHz channel with the following features. Compressor Reduces the background noise flow and the speech signal at transmitting radio. 6.9.3.7 Hear Clear Companding 56 MN006727A01-AA Advanced Features Expander Expands the speech while the noise flow remains the same at receiving radio. Random FM Noise Canceller (Flutter Fighter) Reduces the unwanted effects of random FM noise pulses caused by channel fading under high Signal-to-Noise (S/N) conditions such as in a moving transportation. The fading effects, heard as audio pops and clicks, are canceled without affecting the desired audio signal. The Random FM Noise Canceller operates only in receive mode. NOTICE: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. 6.10 Radio Inhibit This feature allows the system administrator to put a radio into a non-functional state when the radio is missing or in an unknown hand. The radio stays in this state regardless of its power changes. NOTICE:

If the radio has Inter-system roaming capability, the system administrator is able to put the radio into a non-functional state when the missing radio roams to another system. The radio can only be uninhibited by receiving an uninhibited command from the system administrator. 6.11 Global Positioning System/Global Navigation Satellite System The Global Navigation Satellite System (GNSS) in the radio integrates the information from the Global Positioning System (GPS) and the GLObal NAvigation Satellite System (GLONASS) to determine the approximate geographical location of your radio. NOTICE: This feature is addressed as GPS across the manual as the naming convention of the buttons and strings remain the same as the legacy feature of GPS. The availability and accuracy of this location information (and the amount of time that it takes to calculate it) varies depending on the environment in which you are using the GPS feature. For example, GPS location fixes are difficult to obtain indoors, in covered locations, between high buildings, or in situations where you have not established a clear broad view of the sky. If adequate signals from multiple satellites are available, your GPS feature only provides an approximate location, usually within 10 meters from your actual location, but sometimes farther away. 6.11.1 GPS Performance Enhancement Sometimes, the GPS feature may be unable to complete a location calculation successfully. You then see a message indicating that your radio cannot connect to enough visible satellites. To maximize the ability of your radio to determine a fix, take note of the following guidelines:

For your initial fix, hold the radio in the face position. Stay in the open. The GPS feature works best where there is nothing between your radio and the open sky. 57 This feature allows you to select different display formats of GPS location. The following GPS location formats are available:

MN006727A01-AA Advanced Features 6.11.2 Location Format Lat/Long(DD) Lat/Long(DDM) Lat/Long(DMS) UTM/UCS SLD99 MGRS NOTICE: When you send your location to another radio, the receiving radio displays the location in its selected format. 6.11.3 Location Feature in Emergency Mode When the Emergency feature is activated, the radio exits the Location menu and returns to the Home screen for you to view the channel that triggers the emergency signal. You may re-enter the Location menu while still in Emergency mode as long as Silent Emergency is not activated. If you have disabled the Location feature on your radio, it automatically turns back on when Emergency mode is activated. If there is a solid location signal during Emergency operation, the current location and the location information received is saved as Emergency and Last Known Location waypoints respectively. 6.12 Mission Critical Geofence (ASTRO 25 Trunking) This feature allows the radio to use the GPS receiver to determine its location at frequent intervals and evaluate if the radio is within the Geofence area in real time. Geofence is a virtual perimeter based on the GPS to define a geographical area on earth. When the radio enters the predefined Geofence area, your radio receives the Dynamic Regroup command from the system and immediately connects to a Dynamic Regroup talkgroup. The radio display shows the new selected Dynamic Regrouped talkgroup with green intelligent light for your attention. Voice Announcement is also available to support this feature. Any new text messages received at Geofence is displayed immediately on the radio display. NOTICE: If the radio is set up in DVRS, only mobile radio is supported for this feature. 6.12.1 Entering the Geofence Area Prerequisites: The Voice Announcement in this feature is optional. They must be configured to enable you to hear and see these indicators. When and where to use: When the radio enters a Geofence area, the radio immediately sends a message ACK back to the system. The radio searches the current zone for the channel with same talkgroup assigned as the Dynamic Talkgroup and also with same system ID of current trunk system. Once matched, the radio display shows the first matched and connected channel alias. 58 MN006727A01-AA Advanced Features If there is no channel with matching Talkgroup ID and trunk system ID, the radio display shows the channel alias of <DYNAMIC talkgroup>. Once the radio is connected, you hear a dynamic regroup tone, the radio display shows <DYNAMIC channel> with the temporary green color intelligent backlight and you hear a Voice Announcement. NOTICE:

When the radio loses the GPS signal, the GPS icon blinks and the radio sounds two high-

pitched tones repetitively to indicate that the GPS has failed to operate. The radio display shows the red intelligent light. If the first matched channel is not configured with Voice Announcement, no Voice Announcement is played. Procedure:

The other operations are the same as normal dynamic regroup command. When the radio exits the Geofence area, your radio reverts to original channel or newly assigned talkgroup. The radio display shows the new channel together with Voice Announcement to indicate the changes. Voice Announcement of the new channel only works if that channel is configured with Voice Announcement. 6.12.2 Mission Critical Geofence This feature allows the radio to use the GPS receiver to determine radio location at frequent intervals and evaluate if the radio is within the Geofence area in real time Check with your dealer or qualified technician to program the geofence coordinates and actions. 6.12.3 Entering Mission Critical Geofence When and where to use:

When the radio enters the predefined Geofence area, the radio displays <Geofence Alias> with the intelligent backlight and you hear a Voice Announcement. Zone and channel alias of the Geofence area is displayed. If the radio is set to manual, you can choose either to proceed with zone and channel change or cancel the change. The radio then connects to the designated talkgroup. The radio displays the talkgroup alias and dynamic regroup tone sounds. The transmit power level changes and the radio shows a direct text message content without any user operation. NOTICE:

The availability of the Voice Announcement (VA), TMS display, Intelligent Backlight, and Transmit Power Level alerts depend on your radio configuration. The VA can be programmed to alert continuously or momentarily. If Site Selectable Alert (SSA) is enabled, the radio mutes any alert that is received when entering the Geofence area and unmutes when exiting. 6.12.4 Exiting Mission Critical Geofence When and where to use:

When the radio exits the Geofence area, the radio reverts to the original transmit power level, intelligent lighting, channel, or newly assigned talkgroup. Voice announcement is canceled or you hear 59 MN006727A01-AA Advanced Features a preprogrammed VA tone. The radio displays the new channel and a message is received to indicate the changes. 6.13 Trunking System Controls This chapters explain the trunking system control features in your radio. 6.13.1 Operating in Failsoft System When and where to use:

The failsoft system ensures continuous radio communication during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel. During failsoft operation, your radio transmits and receives in conventional operation on a predetermined frequency. You hear a medium-pitched tone and the display shows FAILSOFT. When the trunking system returns to normal operation, your radio automatically leaves failsoft operation and returns to trunked operation. To continue in Failsoft and to communicate with other talkgroups, refer to the following procedure. Procedure:

1 Rotate the 16Position Select Knob to change to a different repeater frequency. 2 Press the PTT button to talk, and release the button to listen. When your radio goes out of the range of the system, it can no longer lock onto a control channel. You hear a low-pitched tone and/or the display shows the currently selected zone/channel combination and Out of range notification. Your radio remains in this out-of-range condition until it locks onto a control channel or failsoft channel, or if it is turned off. 6.13.2 Out-of-Range Radio 6.13.3 SmartConnect SmartConnect allows your radio to maintain voice communication when LMR is out of range by switching to a Wi-Fi, LTE through Tethered Data Modem and Satellite through Ethernet. Before switching broadband connections, your radio compares the relative signal strength of the various broadband connection types to one another, as well as LMR. Your radio remains or returns to LMR connection when the other broadband connections fall below the quality threshold. In addition, a radio operating on a lower priority broadband connection returns to the higher priority or quality connection while idle on SmartConnect. NOTICE: This feature must be preprogrammed by a qualified radio technician. Contact your system administrator for more information. Your radio can connect through a fixed Wi-Fi access point in buildings or in-vehicle Broadband modem such as the following modems:

Motorola Solutions VML750 Sierra Wireless MP70 Sierra Wireless GX450 60 MN006727A01-AA Advanced Features Your radio displays the SmartConnect capable icon the device is connected to an available network, the radio displays SmartConnect connection icon on the SmartConnect enabled channel, once Your radio displays Out of Range when both LMR and SmartConnect are unavailable. 6.13.4 Site Trunking Feature If the Zone Controller loses communication with any site, that site reverts to site trunking. When this occurs, you can communicate only with the radios within your trunking site. If the Zone Controller loses communication with any site, that site reverts to site trunking. When this occurs, you can communicate only with the radios within your trunking site. The display shows the currently selected zone/channel and the Site Trunking message. 6.13.5 Locking and Unlocking a Site When and where to use: This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system. Procedure:

Use the preprogrammed Site Lock/Unlock button to toggle the lock state between locked and unlocked. The radio saves the new site lock state and returns to the Home screen. 6.13.6 Viewing the Current Site Procedure:

Press the preprogrammed Site Displ/Srch button. The display shows momentarily the name of the current site and its corresponding received RSSI. 6.13.7 Changing the Current Site Procedure:

Press and hold down the preprogrammed Site Displ/Srch button. You hear a tone and the display shows momentary SCANNING. When the radio finds a new site, it returns to the Home screen. 6.14 Mission Critical Wireless Bluetooth This feature allows your radio to extend its functionality by connecting to external proprietary Motorola Solutions accessories. Use Motorola Solutions proprietary Mission Critical Wireless (MCW) devices 61 with APX radios during Mission Critical operations as other Bluetooth devices may or may not meet the mission critical standard. By default, Bluetooth is activated on your radio. Your radio supports the following Bluetooth devices or profiles:

MN006727A01-AA Advanced Features Headset (HSP) Dial Up Networking (DUN) Personal Area Networking (PAN) Serial Port (SPP) Generic Access Profile (GAP) General Attribute Profile (GATT) 6.14.1 Turning On Bluetooth When and where to use:

Procedure:

Turning on the Bluetooth using the preprogrammed button:

a. Press the preprogrammed button to turn on the Bluetooth. You hear a short, medium-pitched tone. The display shows momentarily BT ON, and appears. If Bluetooth fails to launch, the display shows BT ON FL. 6.14.2 Turning Off the Bluetooth Procedure:

Turning off the Bluetooth using the preprogrammed button:

a. Press the preprogrammed button to turn off the Bluetooth. You hear a short, medium-pitched tone. The display shows momentary BT OFF and disappears. 6.14.3 Pairing with Low Frequency-Motorola Proximity Pairing (LF-MPP) Feature Prerequisites:

Ensure that Bluetooth feature of your radio is on and the Bluetooth tones are enabled. Bluetooth tones, Bluetooth menu and preprogrammed buttons must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. When and where to use: The range of Bluetooth operation when using a MCW accessory is 10 meters line-of-sight communication. This is an unobstructed path between the location of the signal transmitter (your radio) and the location of the receiver (your device or accessory). Obstacles that can cause an obstruction in the line-of-sight include trees, buildings, mountains, cars, and others. 62 MN006727A01-AA Advanced Features For high degree of reliability, Motorola Solutions recommends to NOT separate the radio and the accessory. At the fringe areas of reception, both voice and tone quality will start to sound "garbled" or "broken". To correct this problem, simply position the accessory and radio closer to each other (within the 10 meter defined range) to re-establish clear audio reception. NOTICE: Once a COTS headset is paired to your radio, it is always connected. Therefore the battery life of the accessory is aligned with the Talk Time power consumption, not the Standby Time consumption. Procedure:

Turn on the accessory. Then, place it close to the radio aligning the Bluetooth Pairing Location

(a blue dot) on the radio to the Bluetooth Pairing Location (a blue dot) on the accessory. If the pairing process is successful, you hear an incremental-pitched tone. The radio begins to connect to the device. If the pairing process fails, you hear a short, low-pitched tone. The display shows PAIRFAIL. Repeat this step. The radio tries to establish connection with the device once paired. NOTICE: If the connection fails within 6 seconds, you hear a decremental-pitched tone to indicate that the device is unpaired. The display shows <Device Type> UNPAIRED. Repeat this step to re-initiate the pairing process. If the connection is successful, you hear an incremental-pitched tone. The display shows <Device Type> CONNCTED and the Bluetooth icon turns from to

. If the radio has the pairing record of the device and the connection fails, you hear a short, low-pitched tone. The display shows <Device Type> CON FAIL. 6.14.4 Standard Pairing Feature The Bluetooth Standard Pairing feature enables your Bluetooth enabled radio to search for other Bluetooth enabled and discoverable devices. NOTICE: Bluetooth tones, Bluetooth menu, and preprogrammed buttons must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. Once the device is discovered, your radio automatically pairs with the device. 6.14.4.1 Searching and Pairing the Bluetooth Device Prerequisites: Ensure the Bluetooth on your device is turned on and is set to Discoverable in order to enable your radio to detect your device in Bluetooth. When and where to use: Bluetooth Search in Bluetooth Standard Pairing method is used to scan for other Bluetooth devices nearby. It is set to turn off by default. 63 MN006727A01-AA Advanced Features Procedure:

The radio only search for HSP devices and Motorola Solutions MCW & OCW accessories. Radio filters out other profiles. Press the preprogrammed Bluetooth Inquiry On/Off button, to enable the Bluetooth Search feature. One of the following scenarios occurs:

If successful, the display shows SRCH ON followed by SRCH END when the radio is pairing with a device found. The display shows <Device Name> PAIRED to indicate pairing is complete. If the feature fails to initiate or the radio fails to pair with any device, the display shows SRCH END when the search timer expires without pairing with any device. Repeat this step. One of the following scenarios occurs:

The radio continues to connect to the device. If the connecting process is successful, the radio sounds an incremental-pitched tone. The display shows <Device Type>CONNCTED, and the Bluetooth icon turns from b to a. If the device already has pairing records and the connecting process fails, the radio sounds a short, low-pitched tone. The display shows <Device Type> CON FAIL. If the connection fails within 6 seconds, you hear a decremental-pitched tone to indicate that the device is unpaired. The display shows <Device Type> UNPAIRED. 6.14.4.2 Turning On Bluetooth Visibility When and where to use: Turning Bluetooth visibility on enables other Bluetooth devices to search for your radio. The visibility of the Bluetooth is set to turn off by default. a. Press and hold the preprogrammed Bluetooth Inquiry On/ Off button for three seconds to Procedure:

enable the Bluetooth visibility feature. One of the following scenarios occurs:

Keep holding the button although you hear a short, medium-pitched tone with the display shows momentary VISIBLE. This indicates the visibility is turned on successfully.1 If the visibility fails to turn on, the display shows VISIBLTYFAILED. When the timer expires, the display shows VISI OFF. 6.14.4.3 Receiving Pairing Request from other Devices Procedure:

Turn on your radio Bluetooth Visible mode. Your radio automatically accept the request and pair with any request received from other device. 1 Releasing the preprogrammed button turns off the Visibility mode. 64 MN006727A01-AA Advanced Features 6.14.5 Turning On the Bluetooth Audio Procedure:

Turning on the Bluetooth audio using the preprogrammed button:

a. Press the preprogrammed Bluetooth Audio Reroute button to route the audio from the radio to the headset. You hear a short, medium-pitched tone. The display shows HDSET ON. BT audio routing can be configured in CPS to route the audio to RSM or radio's internal speaker. The audio routes to the radio's speaker if RSM is not connected. Check with your dealer or system administrator for more information on the programming of this feature. NOTICE: For BT PTT press, the active microphone can be configured in CPS to transmit from either the RSM, the radio microphone, or the BT headset. If the configured device is not available, audio transmission reverts to BT headset. 6.14.6 Turning Off the Bluetooth Audio Procedure:

Turning off the Bluetooth audio using the preprogrammed button:

a. Press the preprogrammed Bluetooth Audio Reroute button to route the audio from the headset to the radio. You hear a short, medium-pitched tone. The display shows SPKR ON. 6.14.7 Adjusting the Volume of the Radio from Bluetooth Audio Device Prerequisites: Ensure that the Bluetooth audio device is connected to the radio. When and where to use:

Your radio can only control the volume of MCW and OCW Bluetooth enabled audio device. If the radio is paired with other Bluetooth enabled audio device, its volume is independent from the APX radio. In this case, the volume is only adjustable on the device. Adjust volume up/down on the Bluetooth audio device. The radio display shows VOL XX and sounds a short, medium-pitched tone. 6.14.8 Clearing All Bluetooth Devices Information Procedure:

Procedure:

Clearing all Bluetooth devices information using the preprogrammed Bluetooth On/Off button:

a. Long press the preprogrammed Bluetooth On/Off button. You hear a short, medium-pitched tone. The display shows PLS WAIT to indicate clearing is in progress. 65 MN006727A01-AA Advanced Features Postrequisites:

If successful, the display shows ALL CLR. If unsuccessful, the radio sounds a short, low-pitched tone.The display shows CLR FAIL. NOTICE: If Re-Pair Timer is set to infinite and you clear keys on the radio, you must clear keys on all previously paired devices as well. (Please see your accessories manual for further details.) 6.14.9 Pairing with LEX Handheld Prerequisites: Ensure that Bluetooth feature of your radio is on and the Bluetooth tones are enabled. Procedure:

1 Turn on the handheld and activate the Bluetooth feature. 2 Place the handheld close to the radio aligning the Bluetooth Pairing Location on the handheld with the Bluetooth Pairing Location on the radio. If the pairing process is successful, you hear an incremental-pitched tone from the radio. The radio begins to connect to the handheld. If the connecting process is successful, you hear an incremental-pitched tone. The display shows <Device Friendly Name> connected, and the Bluetooth icon turns from to

. If unsuccessful, one of the following scenarios occur:

You hear a short, low-pitched tone and the display shows Bluetooth pairing failed (if pairing fails). You hear a decremental-pitched tone and the display shows <Device Friendly Name>

unpaired (if the connection fails within 6 seconds). You hear a short, low-pitched tone and the display shows <Device Friendly Name>

connect failed (if the radio has the pairing record of the handheld and the connection fails). Repeat this step to re-initiate the pairing process. NOTICE: To unpair the handheld after a successful connection, follow the steps in Viewing and Clearing the Bluetooth Device Information. 6.14.10 Responder Alert Sensors Responder alert sensors allow the radio to send an over-the-air (OTA) notification when the radio receives the holster, weapon fired, and vest pierced sensor events. To enable the feature, ensure that the GPS, Enhanced Data, and Bluetooth feature of your radio is on and the radio supports Bluetooth Low Energy (BTLE). You can disable the feature temporarily or permanently. This feature allows you to prevent one or all events from being reported OTA. This feature is enabled through Customer Programming Software (CPS) configuration. Contact your system administrator for more information. 66 MN006727A01-AA Advanced Features NOTICE: The radio reports the next event after the preprogrammed 15-second timer expires. Any consecutive event occurring within the timer is not reported to avoid multiple reports over the same incident. 6.14.10.1 Holster Sensor Holster sensor monitors the state of the holster and allows the radio to send an over-the-air (OTA) notification whenever a gun or a taser is pulled out of the holster or put in the holster. The sensor can cache events that happen when the sensor is disconnected from the radio. When the sensor is reconnected, the radio evaluates and sends the important events OTA to the system. Check with your system administrator for more information about these cached events. If the sensor is disconnected from the radio for more than 30 minutes or it is disabled, the holster sensor clears the cached events. The feature allows the radio to send an over-the-air (OTA) notification when a weapon enabled with the sensor is fired. The event is immediately sent to the system to alert the dispatcher of the weapon fired incident. 6.14.10.2 Weapon Fired Sensor 6.14.10.3 Vest Pierced Sensor Vest Pierced sensor is located inside a bulletproof vest. The sensor reports an event to the radio when the vest is pierced due to various causes such as bullet shot or knife stabbing. The feature allows the radio to send an emergency message and over-the-air (OTA) notification when a vest piercing event occurs. The event is immediately sent to the system to alert the dispatcher of the vest pierced incident. The receiving radio displays VPierced RCVD to indicate that the sender is in a Vest Pierced Emergency event. 6.14.10.4 Disabling the Sensor This feature disables the sensors temporarily or permanently from sending the sensor events to the system. NOTICE: The feature is only applicable to holster sensor and weapon fired sensor. Vest pierced sensor cannot be disabled. 6.14.10.4.1 Disabling the Sensor Temporarily Procedure:

1 Short-press the preprogrammed Sensor button to activate the sensor timer. The following scenarios affect the sensor state:

If a gun or taser is removed from the holster within the timer duration, the timer stops and switches the sensor to disabled state. A tone sounds and the radio displays Sensor Disable. 67 MN006727A01-AA Advanced Features NOTICE: The radio enables the sensor only when all the guns or tasers are placed into the holster. A tone sounds and the radio displays Sensor On temporarily. If the timer expires without an event, a tone sounds, the radio switches the sensor to enabled state, and clears the sensor status from the display. If the preprogrammed Sensor button is long-pressed, the OTA sensor notification is enabled. 6.14.10.4.2 Disabling the Sensor Permanently Procedure:

1 Long-press the preprogrammed Sensor button to permanently disable the sensors. A tone sounds and the radio displays Sensor Off. While in this state, no events is reported over-the-air (OTA), regardless of how many times the gun is drawn, re-inserted or weapon is fired. The radio generates a bad key tone if the sensor is not allowed to be disabled or there is no sensor connected to the radio when the preprogrammed button or menu select button is pressed. 2 Long-press the preprogrammed Sensor button again to enable the OTA Sensor notification. A tone sounds, and the radio displays SNSR OFF. 6.15 ASTRO 25 (P25) Programming Over Project 25 (POP25) Also called Over-the-Air Programming, this feature allows configuration data and firmware to be upgraded to your radio over-the-air. Full use of the radio is retained during the data transfer without interrupting communication. If the upgrade happens on the ASTRO 25 and ASTRO Conventional systems, the upgrade pauses to give priorities to voice call, and continues after the voice call ended. If the upgrade happens on a Wi-Fi network, the upgrade process runs concurrently with voice calls. Once a configuration upgrade is downloaded to your radio, you can install new changes immediately or delay changes to be installed on the radio when it is being powered up. 6.15.1 Responding to the Notification of Upgrade When and where to use: If a configuration upgrade is downloaded to your radio, an alert tone sounds and the upgrade is installed at the next radio power up. If a firmware upgrade is downloaded to your radio, an alert tone sounds and the display shows UPGRADE. 1 To accept the upgrade, long press the Top Side (Select) button within 15 seconds of UPGRADE appearing on the display. The radio resets and the installation takes several minutes. Procedure:

68 MN006727A01-AA Advanced Features NOTICE: The radio cannot be used while the upgrade is being installed. Therefore, make sure to only accept the upgrade at a convenient time when immediate radio use is not required. If the Top Side (Select) button is not long pressed within 15 seconds, the UPGRADE display is cleared until the next radio power up. 6.16 Voice Announcement This feature enables the radio to audibly indicate the current feature mode, zone, or channel assigned to the user. The available voice announcement priority options are:

High Low Voice announcement is enabled even when the radio is receiving calls. Voice announcement is disabled when the radio is receiving calls. 6.17 Site Selectable Alerts (ASTRO 25 Trunking) A Site Selectable Alert (SSA) is an Intelligent Lighting indicator with audio alert sent to radios at sites to notify the users when there is a special situation that they need to be aware of. Your radio supports up to 250 site aliases. Only authorized radios are enabled to send SSA. NOTICE:

The alert alias, alert tone, and alert period is configured in the Customer Programming Software. Contact your system administrator for more information. When mixing SSA with received voice audio, the SSA alert is reduced in volume to ensure that the voice message is still heard clearly. It is important that the SSA audio files are created with clear loud audio to ensure audio clarity at reduced levels. You can connect your radio to a Wi-Fi network for wireless programming. Your service administrator preprograms the Wi-Fi Service Set Identifier (SSID) or network name that your radio can connect to. 6.18 Wi-Fi 6.18.1 Turning Wi-Fi On or Off Procedure:

Turning Wi-Fi on or off using the preprogrammed button:

a. To toggle the Wi-Fi on or off, press the preprogrammed Wi-Fi button. This button must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. The display shows WIFI ON or WIFI OFF. 69 MN006727A01-AA Advanced Features 6.18.2 Checking the Wi-Fi Configuration and Status of the Radio Procedure:

Long press the preprogrammed Wi-Fi button. The display shows the current status of the Wi-Fi as described next. WF SRCHG Looking for available Wi-Fi networks that have been preprogrammed into the radio. In the process of connecting to a found Wi-Fi network. Connected to one of the preprogrammed Wi-Fi networks. WF CNTG WF CNTD NO SERVICE No available networks or connection with one of the networks failed. If the radio is Wi-Fi connected, you see a Wi-Fi signal strength indicator, on the top display. This chapter explains the operations of the utility functions available in your radio. 6.19 Utilities 6.19.1 Using the Flip Display When and where to use: This feature allows you to flip the content of the top display upside down. It is particularly useful when you would like to read the top display while the radio is still in the carry holder attached to your belt. Procedure:

To flip the display, press and hold the preprogrammed Light/Flip button. 6.19.2 Selecting a Basic Zone Bank Prerequisites: The Basic Zone Select feature must to be preprogrammed to the 3-position A-B-C switch, while the Basic Zone Bank feature must be preprogrammed to any side button or Top

(Orange) button before you can use this feature. When and where to use: This feature allows twice as many zones to be accessed from a switch, doubling the amount of switch positions. 1 Use the preprogrammed Basic Zone Bank button to toggle the position between Bank 1 and The top display shows the status icons (A, B, C, D, E, or F) or the zone name based on the bank and switch position selected. NOTICE: See the Basic Zone Bank 1 and Basic Zone Bank 2 icons for more information on the status icons. Procedure:

Bank 2. 70 MN006727A01-AA Advanced Features 6.19.3 Selecting the Power Level Prerequisites:

NOTICE: This feature must be preprogrammed by a qualified radio technician. When and where to use: This feature enables you to reduce the transmit power level for specific case that requires a lower power level. You can select the power level at which your radio transmits. The radio always turns on to the default setting. These reduced transmit power level settings do not affect the receiving performance of your radio, nor diminish the overall quality of the audio and data functionality of the radio given the following conditions. Power level Low enables a shorter transmitting distance and to conserve power. Power level High enables a longer transmitting distance. Procedure:

and high power. Use the preprogrammed Transmit Power Level switch to toggle the power level between low The display shows LOW PWR and the low power icon or the display shows HIGH PWR and the high power icon. 6.19.4 Controlling the Display Backlight When and where to use: You can enable or disable the radio display backlight as needed, if poor light conditions make the display difficult to read. NOTICE:

The backlight remains on for a preprogrammed time before it automatically turns off completely or returns to the minimum backlight level. Procedure:

Perform one of the following actions:

To toggle the backlight on or off, press the preprogrammed Light/Flip button. To turn the backlight on, press any programmable radio controls or buttons. 6.19.5 Locking and Unlocking the Controls When and where to use: You can lock the programmable buttons, switches, and rotary knobs of your radio to avoid inadvertent entry. Check with your dealer or qualified technician for best selection to suit your usage. Procedure:

1 Toggle the preprogrammed Keypad/Control Lock button or switch to on. The display shows CTRL LCK. 2 Toggle again to unlock the controls. 71 MN006727A01-AA Advanced Features Procedure:

6.19.6 Turning Voice Mute On or Off When and where to use: You can enable and disable voice transmission, if needed. Turning Voice Mute off or on using the preprogrammed Voice Mute button:

a. To turn the feature off or on, press the preprogrammed Voice Mute button. The display shows momentary VMUT OFF, and you hear a short tone, indicating that the feature is disabled or the display shows momentary VMUT ON, and you hear a short tone, indicating that the feature is enabled. 6.19.7 Using the Time-Out Timer When and where to use: This feature turns off the transmitter of your radio. You cannot transmit longer than the preset timer setting. If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone. The timer is defaulted at 60 seconds, but it can be preprogrammed from 15 to 465 seconds, in 15-

second intervals, or it can be disabled entirely for each radio mode, by a qualified radio technician. NOTICE: You hear a brief, low-pitched, warning tone four seconds before the transmission times out. Procedure:

1 Hold down the PTT button longer than the preprogrammed time. You hear a continuous talk prohibit tone. The transmission is cut off and the LED goes out. 2 Release the PTT button. The timer resets. 3 To re-transmit, press the PTT button. The time-out timer restarts and the LED lights up solid red. 6.19.8 Conventional Squelch Operation This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise. Tone Private Line, Digital Private-Line, and carrier squelch is available (preprogrammed) per channel. Tone Private Line or Digital Private-Line The radio responds only to your messages. Result You hear all traffic on a channel. Analog Options Option Carrier squelch 72 MN006727A01-AA Advanced Features Digital Options One or more of the following options may be preprogrammed in your radio. Contact your system administrator for more information. Option Result Digital Carrier-Operated Squelch You hear all digital traffic. You hear any digital traffic having the correct network access code. You hear any digital traffic having the correct network access code and correct talkgroup. 6.19.8.1 Using Conventional Squelch Operation Features Normal Squelch Selective Switch Procedure:

1 2 3 Perform one of the following actions:

Press the Menu Select button directly below + to increase the squelch volume. Press the Menu Select button directly below - to decrease the squelch volume. 4 Press to return to the selected channel. 6.19.9 Using the PL Defeat Feature This feature allows you to override any coded squelch that preprogrammed to a channel. The radio also unmutes to any digital activity on a digital channel. When this feature is active, the Carrier Squelch status indicator is displayed. Procedure:

Place the preprogrammed PL Defeat switch in the PL Defeat position. One of the following occurs:

The radio plays the active transmission on the channel. If no activity is present, the radio is muted 6.19.10 Digital PTT ID Support This feature allows you to see the radio ID (number) of the radio from whom you are currently receiving a transmission. The receiving radio and the dispatcher can view the ID, which consists of up to a maximum of eight characters. The ID number of your radio is also automatically sent every time you press the PTT button. This feature is preprogrammed per channel. For digital voice transmissions, the ID of your radio is sent continuously during the voice message. 73 MN006727A01-AA Advanced Features 6.19.11 Smart PTT (Conventional Only) Smart PTT is a per-personality, programmable feature used to keep radio users from talking over other radio conversations. When Smart PTT is enabled in your radio, you cannot transmit on an active channel. The following table shows the variations of Smart PTT. Mode Description Transmit Inhibit on Busy Channel with Carrier Transmit Inhibit on Busy Channel with Wrong Squelch Code You cannot transmit if traffic is detected on the channel. You cannot transmit on an active channel with a squelch code or (if secure-equipped) encryption key other than your own. If the PL code is the same as yours, the transmission is not prevent-

ed. Your radio must be preprogrammed to allow you to use Quick-Key Override. This feature works with either one of the two above varia-

tions. You can override the transmit-inhibit state by quick-keying the radio (press PTT button twice within the preprogrammed time limit). Quick-Key Override 6.19.12 Transmit Inhibit This feature allows you to stops all transmission including voice and data. The radio can receive messages but not able to reply the acknowledgment request of the received message. This feature is available for APCO 25 trunking, Type II trunking and Conventional operations for all APX radios. You can physically control the transmission of the radio especially during operation in hazardous environments. An environment is considered hazardous if radio transmission could initiate an explosion or other dangerous reactions. 6.19.12.1 Enabling Transmit Inhibition Procedure:

1 Press the Transmit Inhibit programmable button. NOTICE: If the user has disabled TX Inhibit using the menu and then moves the switch to the position where TX Inhibit is enabled, the new value overwrites the menu value. The display shows Tx inhibit on. You hear a sequence of short, low-high tones to indicate that transmission is inhibited. Pressing PTT triggers the radio sounds a constant short, low-pitched tone (reject tone). NOTICE: The status of the Transmit Inhibit does not change after the radio powers up. 74 MN006727A01-AA Advanced Features 6.19.12.2 Disabling Transmit Inhibition Procedure:

1 Press the Transmit Inhibit programmable button. NOTICE: If the user has disabled TX Inhibit using the softkey and then moves the switch to the position where TX Inhibit is enabled, the new value overwrites the menu value. The display shows Tx inhibit off. You hear a sequence of short, high-low tone (Transmit Inhibit Off tone) to indicate that the transmission is back to normal operation. This feature allows you to save the last received call and playback the recorded call. 6.19.13 Instant Recall 6.19.13.1 Saving and Playback Calls When and where to use:

Procedure:

Saving the recorded calls using the preprogrammed Record Playback button:

a. Long press the preprogrammed Record Playback button to save the recorded calls. Radio displays Audio Saved momentarily. Radio plays the saved call automatically if call saving is successful. A tone sounds if call saving is not successful. Playback the saved calls using the preprogrammed Record Playback button:

a. Short press the preprogrammed Record Playback button to playback the saved calls. b. Short press the preprogrammed Record Playback button again to skip to the next saved call. If there is only a single saved call, the playback skips to the end of the call. Radio auto playback the most recent incoming call followed by saved calls in chronological order. Radio displays the playback status. NOTICE:

Received call overwrites the ongoing record playback. User can short press the programmable button within three seconds to continue the playback and ignore the receiving call. User can short press the programmable button to trigger playback when the radio is receiving call to overwrite the receiving call. Playback can be halted by any tone and button press except for specific buttons. Check with your dealer or system administrator for more information. 75 MN006727A01-AA Accessories Accessories Not all accessories are FCC certified to operate with all radio models and/or bandsplits. Refer to the radio price pages for a list of FCC certified accessories or contact your sales representative for accessory compatibility. Visit http://www.motorolasolutions.com to know more about the accessories supported by this radio. 76 MN006727A01-AA Legal and Compliance Statement Legal and Compliance Statement Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola Solutions reserves the right to change any products to improve readability, function, or design. Motorola Solutions does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others. Copyrights The Motorola Solutions products described in this document may include copyrighted Motorola Solutions computer programs. Laws in the United States and other countries preserve for Motorola Solutions certain exclusive rights for copyrighted computer programs. Accordingly, any copyrighted Motorola Solutions computer programs contained in the Motorola Solutions products described in this document may not be copied or reproduced in any manner without the express written permission of Motorola Solutions. 2020 Motorola Solutions, Inc. All Rights Reserved No part of this document may be reproduced, transmitted, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without the prior written permission of Motorola Solutions, Inc. Furthermore, the purchase of Motorola Solutions products shall not be deemed to grant either directly or by implication, estoppel or otherwise, any license under the copyrights, patents or patent applications of Motorola Solutions, except for the normal non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product. Please note that certain features, facilities, and capabilities described in this document may not be applicable to or licensed for use on a specific system, or may be dependent upon the characteristics of a specific mobile subscriber unit or configuration of certain parameters. Please refer to your Motorola Solutions contact for further information. Disclaimer Trademarks MOTOROLA, MOTO, MOTOROLA SOLUTIONS, and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. European Union (EU) Waste of Electrical and Electronic Equipment (WEEE) directive The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries should not dispose of electronic and electrical equipment or accessories in household waste. 77 MN006727A01-AA Legal and Compliance Statement Customers or end-users in EU countries should contact their local equipment supplier representative or service centre for information about the waste collection system in their country. Declaration of Conformity Per FCC CFR 47 Part 2 Section 2.1077(a) This declaration is applicable to your radio only if your radio is labeled with the following FCC logo. Responsible Party Name: Motorola Solutions, Inc. Phone Number: 1-800-927-2744 Address: 1303 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A. Hereby declares that APX 8000HXE conforms to FCC Part 15, subpart B, section 15.107(a), 15.107(d), and section 15.109(a) Class B Digital Device As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1 This device may not cause harmful interference, and 2 This device must accept any interference received, including interference that may cause undesired operation. NOTICE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. 78 MN006727A01-AA Legal and Compliance Statement Important Safety Information RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios CAUTION:

This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. For a list of Motorola Solutions-approved antennas, batteries, and other accessories, visit the following website:

http://www.motorolasolutions.com Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter is approved by Industry Canada to operate with a Motorola Solutions-approved antenna with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Notice to Users (FCC) This device complies with Part 15 of the FCC rules per the following conditions:

This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this device, not expressly approved by Motorola Solutions, could void the authority of the user to operate this equipment. FCC Licensing Information This device complies with Parts 90 and 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the condition that this device does not cause harmful interference. The radio operates on radio frequencies that are regulated by the Federal Communications Commission (FCC). To transmit on these frequencies, you are required to have a license issued by the FCC. Application is made available on FCC Form 601 and Schedules D, H, and Remittance Form 159. To obtain these FCC forms, request document 000601 which includes all forms and instructions. If you wish to have the document faxed, mailed or have questions, use the following contact information. Contact the Fax-On-Demand system at 1-202-418-0177 Call the FCC forms hotline at 1-800-418-FORM or 1-800-418-3676 Fax Mail Contact For questions regarding FCC license, contact 1-888-CALL-FCC, 1-888-225-5322, or http://

www.fcc.gov. Before filling out your application, you must decide which frequency you can operate on. For questions on determining the radio frequency, call Motorola Solutions Product Services at: 1-800-448- 6686. Changes or modifications not expressly approved by Motorola Solutions may void the user authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, 79 MN006727A01-AA Legal and Compliance Statement transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component such as crystal, semiconductor, and others not authorized by the FCC equipment authorization for this radio could violate FCC rules. NOTICE: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited. Canada Licensing Information Notice to Users (Industry Canada) The operation of your Motorola Solutions radio is subject to the Radiocommunications Act and must comply with rules and regulations of the Federal Government's department of Industry Canada. Industry Canada requires that all operators using Private Land Mobile frequencies obtain a radio license before operating their equipment. 1 Fill in the items as per the instructions. If you need additional space for any item use the reverse The License Application side of the application. 2 Be sure to print legibly 3 Make a copy for your files. 4 Prepare a cheque or money made out to the "Receiver General for Canada", for an amount, which is on the following schedule, for each radio purchased. (License is renewed on April 1st each year, and issued for a period of 12 months). 5 Mail your completed application, along with your cheque or money order to the closest Industry Canada District office, according to the list on pages. To obtain the latest Canadian License Application form, please go to http://www.ic.gc.ca/ic_wp-pa.htm. 80 MN006727A01-AA Maritime Radio Use in the VHF Frequency Range Maritime Radio Use in the VHF Frequency Range Special Channel Assignments Emergency Channel If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order:

1 MAYDAY, MAYDAY, MAYDAY. 2 THIS IS _____________________, CALL SIGN __________. State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times. 3 Repeat MAYDAY and the name of the vessel. 4 WE ARE LOCATED AT _______________________. State the position of the vessel in distress, using any information that will help responders to locate you, e.g.:

latitude and longitude bearing (state whether you are using true or magnetic north) distance to a well-known landmark vessel course, speed or destination 5 State the nature of the distress. 6 Specify what kind of assistance you need. length and/or tonnage, hull color, etc. 9 OVER. 10 Wait for a response. 7 State the number of persons on board and the number needing medical attention, if any. 8 Mention any other information that would be helpful to responders, such as type of vessel, vessel 11 If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you. Non-Commercial Call Channel For non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9. Operating Frequency Requirements A radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows:

on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency. on ships subject to the Safety Convention, the radio must be capable of operating:

in the simplex mode on the ship station transmitting frequencies specified in the 156.025 157.425 MHz frequency band, and 81 MN006727A01-AA Maritime Radio Use in the VHF Frequency Range

in the semiduplex mode on the two frequency channels specified in the table below. NOTICE:

Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast Guard. Table 3: VHF Marine Channel List Channel Number Frequency (MHz) 1 2

4 5 6 7 8 9 10 11 12 13**

14 15**

16 17**

18 19 20 22

24 25 26 27 28 60 82 Transmit 156.050 156.100 156.150 156.200 156.250 156.300 156.350 156.400 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 156.850 156.900 156.950 157.000 157.050 157.100 157.150 157.200 157.250 157.300 157.350 157.400 156.025 Receive 160.650 160.700 160.750 160.800 160.850 160.950 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 156.850 161.500 161.550 161.600 161.650 161.700 161.750 161.800 161.850 161.900 161.950 162.000 160.625 67**

77**

62 63

65 66 68 69 71 72 73 74 75 76 78 79 80

84 85 86 87 88 156.075 156.125 156.175 156.225 156.275 156.325 156.375 156.425 156.475 156.575 156.625 156.675 156.725

156.875 156.925 156.975 157.025 157.075 157.125 157.175 157.225 157.275 157.325 157.375 157.425 MN006727A01-AA Maritime Radio Use in the VHF Frequency Range 160.675 160.725 160.775 160.825 160.875 160.925 156.375 156.425 156.475 156.575 156.675 156.725

161.525 161.575 161.625 161.675 161.725 161.775 161.825 161.875 161.925 161.975 162.025 83 NOTICE:

* Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.

** Low power (1 W) only.

*** Guard band. NOTICE: A in the Receive column indicates that the channel is transmit only. MN006727A01-AA Maritime Radio Use in the VHF Frequency Range Declaration of Compliance for the Use of Distress and Safety Frequencies The radio equipment does not employ a modulation other than the internationally adopted modulation for maritime use when it operates on the distress and safety frequencies specified in RSS-182 Section 7.3. Technical Parameters for Interfacing External Data Sources Input Voltage (Volts Peak-to-peak) Max Data Rate Impedance RS232 18 V 115 Kbps 5000 USB 3.6 V 12 Mbps 90 SB9600 5 V 9.6 Kbps 120 84 MN006727A01-AA Limited Warranty Limited Warranty MOTOROLA SOLUTIONS COMMUNICATION PRODUCTS I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:

MOTOROLA SOLUTIONS, INC. (MOTOROLA) warrants the MOTOROLA SOLUTIONS manufactured Communication Products listed below (Product) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:

ASTRO APX 8000HXE Portable Units Product Accessories For LACR region:

One (1) Year One (1) Year ASTRO APX 8000HXE Portable Units Three (3) Years Product Accessories One (1) Year MOTOROLA SOLUTIONS, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA SOLUTIONS. This express limited warranty is extended by MOTOROLA SOLUTIONS to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA SOLUTIONS. MOTOROLA SOLUTIONS assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA SOLUTIONS. Unless made in a separate agreement between MOTOROLA SOLUTIONS and the original end user purchaser, MOTOROLA SOLUTIONS does not warrant the installation, maintenance or service of the Product. MOTOROLA SOLUTIONS cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA SOLUTIONS which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA SOLUTIONS disclaims liability for range, coverage, or operation of the system as a whole under this warranty. MOTOROLA SOLUTIONS offers the following optional extended service contracts. DEVICE MANAGED SERVICES (DMS) ACCIDENTAL DAMAGE Provides for extended hardware repair coverage INCLUDING CHEMICAL, LIQUID, FIRE, AND OTHER PHYSICAL DAMAGE. Accidental damage coverage is available in conjunction with MOTOROLA SOLUTIONSS standard Commercial Warranty and starts from the FIRST DAY the radio is put into use. Service performed under this plan consists of repair or replacement of the covered equipment as set forth in the terms and conditions. Repairs will be made only at the designated MOTOROLA SOLUTIONS repair depot. Local services are not included. MOTOROLA SOLUTIONS will pay the inbound shipping charges only with use of the MOTOROLA SOLUTIONS designated 85 MN006727A01-AA Limited Warranty delivery service. MOTOROLA SOLUTIONS will pay for outbound shipping via MOTOROLA SOLUTIONS'S normal shipping methods. DEVICE MANAGED SERVICES (DMS) STANDARD HARDWARE Provides extended hardware normal wear and tear repair coverage beginning AFTER MOTOROLA SOLUTIONSS standard Commercial Warranty period expires. Service performed under this plan consists of repair of the covered equipment as set forth in the terms and conditions. Repairs will be made only at the designated MOTOROLA SOLUTIONS repair depot. Local services are not included. MOTOROLA SOLUTIONS will pay for outbound shipping via MOTOROLA SOLUTIONS'S normal shipping methods. II. GENERAL PROVISIONS:

This warranty sets forth the full extent of MOTOROLA SOLUTIONS'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLA SOLUTIONSs option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA SOLUTIONS BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. III. STATE LAW RIGHTS:

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. IV. HOW TO GET WARRANTY SERVICE:

You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA SOLUTIONS through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA SOLUTIONS at 1-800-927-2744 US/Canada. V. WHAT THIS WARRANTY DOES NOT COVER:

1 Defects or damage resulting from use of the Product in other than its normal and customary manner. 2 Defects or damage from misuse, accident, water, or neglect. 3 Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. 4 Breakage or damage to antennas unless caused directly by defects in material workmanship. 5 A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA SOLUTIONS supplied equipment) 86 MN006727A01-AA Limited Warranty which adversely affect performance of the Product or interfere with MOTOROLA SOLUTIONS's normal warranty inspection and testing of the Product to verify any warranty claim. 6 Product which has had the serial number removed or made illegible. 7 Rechargeable batteries if:

any of the seals on the battery enclosure of cells are broken or show evidence of tampering. the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified. 8 Freight costs to the repair depot. 9 A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA SOLUTIONSs published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA SOLUTIONS. 10 Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. 11 Normal and customary wear and tear. VI. PATENT AND SOFTWARE PROVISIONS:

MOTOROLA SOLUTIONS will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA SOLUTIONS will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:

1 that MOTOROLA SOLUTIONS will be notified promptly in writing by such purchaser of any notice of such claim, 2 that MOTOROLA SOLUTIONS will have sole control of the defense of such suit and all negotiations for its settlement or compromise, and 3 should the Product or parts become, or in MOTOROLA SOLUTIONSs opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA SOLUTIONS, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-

infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA SOLUTIONS. MOTOROLA SOLUTIONS will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA SOLUTIONS, nor will MOTOROLA SOLUTIONS have any liability for the use of ancillary equipment or software not furnished by MOTOROLA SOLUTIONS which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA SOLUTIONS with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA SOLUTIONS certain exclusive rights for copyrighted MOTOROLA SOLUTIONS software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA SOLUTIONS software. MOTOROLA SOLUTIONS software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA SOLUTIONS software or exercise of rights in such MOTOROLA SOLUTIONS software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA SOLUTIONS patent rights or copyrights. 87 MN006727A01-AA Limited Warranty VII. GOVERNING LAW:

This Warranty is governed by the laws of the State of Illinois, U.S.A. VIII. For Australia Only This warranty is given by Motorola Solutions Australia Pty Limited (ABN 16 004 742 312) of Tally Ho Business Park, 10 Wesley Court. Burwood East, Victoria. Our goods come with guarantees that cannot be excluded under the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Motorola Solutions Australias limited warranty above is in addition to any rights and remedies you may have under the Australian Consumer Law. If you have any queries, please call Motorola Solutions Australia at 1800 457 439. You may also visit our website: http://www.motorolasolutions.com/XA-EN/

Pages/Contact_Us for the most updated warranty terms. 88 MN006727A01-AA Glossary This glossary contains an alphabetical listing of terms and their definitions that are applicable to portable and mobile subscriber radio products. Glossary ACK Acknowledgment of communication. Active Channel A channel that has traffic on it. ARS Automatic Registration Service Analog Signal An RF signal that has a continuous nature rather than a pulsed or discrete nature. ASTRO 25 Motorola Solutions standard for wireless digital trunked communications. ASTRO conventional Motorola Solutions standard for wireless analog or digital conventional communications. Autoscan A feature that allows the radio to automatically scan the members of a scan list. Bluetooth Bluetooth is an open wireless technology standard for exchanging data over short distances from fixed and mobile devices with high levels of security. Bluetooth Pairing Bluetooth pairing occurs when two bluetooth devices exchanged a passkey to form a paired Bluetooth wireless connection. Call Alert Privately paging an individual by sending an audible tone. Carrier Squelch Feature that responds to the presence of an RF carrier by opening or unmuting (turning on) a receiver audio circuit. A squelch circuit silences the radio when no signal is being received so that the user does not have to listen to noise. Central Controller A software-controlled, computer-driven device that receives and generates data for the trunked radios assigned to it. It Monitors and directs the operations of the trunked repeaters. 89 MN006727A01-AA Glossary Channel A group of characteristics, such as transmit/receive frequency pairs, radio parameters, and encryption encoding. Control Channel In a trunking system, one of the channels that is used to provide a continuous, two-way/data-

communications path between the central controller and all radios on the system. Conventional Typically refers to radio-to-radio communications, sometimes through a repeater. Frequencies are shared with other users without the aid of a central controller to assign communications channels. Conventional Scan List A scan list that includes only conventional channels. COTS Commercial Off-The-Shelf. Cursor A visual tracking marker (a blinking line) that indicates a location on a display. Digital Private Line (DPL) A type of digital communications that utilizes privacy call, as well as memory channel and busy channel lock out to enhance communication efficiency. Digital Signal An RF signal that has a pulsed, or discrete, nature, rather than a continuous nature. Dispatcher An individual who has radio-system management duties and responsibilities. Digital Signal Processor A microcontroller specifically designed for performing the mathematics involved in manipulating analog information, such as sound, that has been converted into a digital form. DSP also implies the use of a data compression technique. Dynamic Regrouping A feature that allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. Failsoft A backup system that allows communication in a non-trunked, conventional mode if the trunked system fails. FCC Federal Communications Commission. Hang up 90 MN006727A01-AA Glossary Disconnect. IV&D Integrated Voice and Data. Key Variable Loader (KVL) A portable, handheld, rugged device used to transfer encryption keys to a target device. Encryption keys can be entered manually by the KVL user, auto-generated by the KVL, obtained from or shared with another KVL, or downloaded from a Key Management Facility

(KMF). Liquid-Crystal Display (LCD) An LCD uses two sheets of polarizing material with a liquid-crystal solution between them. An electric current passed through the liquid causes the crystals to align so that light cannot pass through them. Light Emitting Diode (LED) An electronic device that lights up when current is passed through it. Li-Ion Lithium ion. Man Down A life-saving feature that senses the radio user may be in trouble by monitoring the whether the radio is in a vertical or horizontal position or whether the radio is motionless. When this feature is triggered, the radio alerts the user with audio and visual alerts. It can also trigger Emergency Alarm the Post-Alert Timer is not cancelled. MCW Mission Critical Wireless. MDC Motorola Solutions Digital Communications. Monitor Check channel activity by pressing the Monitor button. If the channel is clear, you hear static. If the channel is in use, you hear conversation. It also serves as a way to check the volume level of the radio, since the radio opens the squelch when the monitor button is pressed. Multi-System Talkgroup Scan List A scan list that can include both talkgroups (trunked) and channels (conventional). Network Access Code Network Access Code (NAC) operates on digital channels to reduce voice channel interference between adjacent systems and sites. NiMH Nickel-metal-hydride. Non-tactical/revert 91 The user will talk on a preprogrammed emergency channel. The emergency alarm is sent out on this same channel. MN006727A01-AA Glossary OCW Operation Critical Wireless. Over-The-Air Rekeying Allows the dispatcher to remotely reprogram the encryption keys in the radio. Page A one-way alert with audio and/or display messages. Personality A set of unique features specific to a radio. Preprogrammed A software feature that has been activated by a qualified radio technician. Private (Conversation) Call A feature that lets you have a private conversation with another radio user in the group. Private Line (PL) A sub-audible tone that is transmitted such that only receivers decoding the tone receives it. Programmable A radio control that can have a radio feature assigned to it. Push-to-Talk PTT-The switch or button usually located on the left side of the radio which, when pressed, causes the radio to transmit. When the PTT is released, the unit returns to receive operation. Radio Frequency RF-The portion of the electromagnetic spectrum between audio sound and infrared light (approximately 10 kHz to 10 GHz). Repeater Remote transmit/receive facility that re-transmits received signals in order to improve communications range and coverage (conventional operation). selective switch Any digital P25 traffic having the correct Network Access Code and the correct talkgroup. Squelch Muting of audio circuits when received signal levels fall below a pre-determined value. With carrier squelch, all channel activity that exceeds the preset squelch level can be heard. Synchronous Serial Interface (SSI) 92 MN006727A01-AA Glossary DSP interface to peripherals that consists of a clock signal line, a frame synchronization signal line, and a data line. Standby An operating condition whereby the radios speaker is muted but still continues to receive data. Status Calls Pre-defined text messages that allow the user to send a conditional message without talking. Tactical/non-revert The user will talk on the channel that was selected before the radio entered the emergency state. TalkAround Bypassing a repeater and talking directly to another unit for local unit-to-unit communications. Talkgroup An organization or group of radio users who communicate with each other using the same communications path. Trunking The automatic sharing of communications paths between a large number of users. Allows users to share a smaller number of frequencies because a repeater or communications path is assigned to a talkgroup for the duration of a conversation. Trunking Priority Monitor scan list A scan list that includes talkgroups that are all from the same trunking system. USK Unique shadow key. VRS Vehicular Repeater System. Zone A grouping of channels. 93

en-US RF Energy Exposure Training and Product Safety Information for Portable Two-Way Radios fr-CA Formation sur lexposition aux RF et information sur la scurit du produit pour radios bidirectionnelles portatives es-LA Capacitacin sobre la exposicin a energa de radiofrecuencia e informacin de proteccin del producto para radios de dos vas porttiles pt-BR Treinamento sobre a Exposio Energia de RF e Informaes de Segurana do Produto para Rdios Portteis Bidirecionais https://learning.motorolasolutions.com/User_Documentation English Caution Before using this radio, read this booklet which contains important operating instructions. For information on product details, brochures, user manuals and approved accessories. Please refer to www.motorolasolutions.com. Compliance with RF Exposure Standards National and international regulations require manufacturers to comply with the RF energy exposure limits for portable two-way radios before they can be marketed. Your Motorola Solutions two-way radio is designed, manufactured, and tested to comply with all applicable national and international regulations for human exposure to radio frequency electromagnetic energy. When two-way radios are used as a consequence of employment, applicable regulations may require users to be fully aware of and able to control their exposure to meet occupational requirements. RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use Notice: This radio is intended for use in occupational/controlled conditions where users are aware of their exposure and can exercise control over their exposure to meet the requirements in national and international regulations. This radio device is not authorized for general population, consumer use. For more information on what RF energy exposure is, and how to control your exposure to ensure compliance with established RF exposure limits, consult the following websites:

https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en http://www.who.int/peh-emf/project/en/

http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf11467.html http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01904.html For additional user training information on exposure requirements, consult the following websites:

https://www.motorolasolutions.com/en_us/about/company-overview/corporate-

responsibility/governance-and-policies/wireless-communication-and-health-

faqs.html http://learning.motorolasolutions.com/

3 English RF Exposure Compliance and Control Guidelines To control your exposure, and ensure compliance with the relevant RF exposure limits, always adhere to the following guidelines:

Do not remove any of the RF Exposure Labels if present from this device or its related accessories. Attach these instructions to the device when you transfer it to other users. Do not use this device if the operational requirements described herein are not met. Operating Instructions Transmit no more than 50% of the time. To transmit (talk), press the Push-To-

Talk (PTT) button. To receive calls, release the PTT button. Transmitting more than 50% of the time may cause RF exposure compliance requirements to be exceeded. Hold the radio in a vertical position in front of the face with the microphone (and other parts of the radio including the antenna) at least 1 in. (2.5 cm) away from the nose or lips. Antenna should be kept away from the eye. When worn on the body, always place the radio in a Motorola Solutions-

approved clip, holder, holster, case, or body harness for this product. DO NOT hold the antenna when the radio is transmitting. DO NOT use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. To ensure continued compliance with applicable RF exposure limits, use only Motorola Solutions approved, supplied or replacement antennas, batteries, and accessories. For a list of Motorola Solutions approved accessories please refer to your user manual or visit www.motorolasolutions.com Acoustic Safety Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the volume of the radio, the sooner your hearing will be affected. Hearing damage from loud noise is sometimes undetectable at first, and can have a cumulative effect. To protect your hearing:

Use the lowest volume necessary to do your job. Turn up the volume only if you are in noisy surroundings. Turn down the volume before adding headset or earpiece. Limit the amount of time you use headsets or earpieces at high volume. 4 English When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear. Medical Devices If you use a personal medical device, such as a pacemaker or hearing aid, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. Holsters Incorporating Magnets Some Motorola Solutions holsters incorporate strong, neodymium magnets. If you use a personal medical device, such as a pacemaker or hearing aid, consult the manufacturer of your device to determine if it can be used in close proximity to magnets. Your physician may be able to assist you in obtaining this information. Also be aware that magnets can damage other products, including cell phones, computers, hard drives, and other electronic devices, as well as credit cards and magnetic media. Keep the holster away from any mechanical device that could be affected by a magnetic field. Consult the manufacturer of your product to determine if your device or product can be used in close proximity to magnets. Notice to Users (FCC) This device complies with Part 15 of the FCC rules per the following conditions:

This device may not cause harmful interference. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this device, not expressly approved by Motorola Solutions, could void the authority of the user to operate this equipment. Operational Warnings The following explains the operational warnings:

For Vehicle With Air Bags Warning:

Refer to vehicle manufacturer's manual prior to installation of electronic equipment to avoid interference with air bag wiring. DO NOT place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. 5 English Potentially Explosive Atmospheres Warning:

Use of a radio that is not intrinsically safe in a potentially explosive atmosphere could result in a serious injury or death. You should only use a certified Intrinsically Safe radio in potentially explosive atmospheres. Explosive atmospheres refer to hazard classified locations that may contain hazardous gas, vapors, dusts, such as fueling areas below decks on boats, fuel or chemical transferor storage facilities, and areas where the air contains chemicals or particles such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often, but not always, posted. Turn off your radio prior to entering any area with a potentially explosive atmosphere unless it is a radio type specifically certified for use in hazardous location areas. DO NOT remove, install, or charge batteries in such areas, or remove or install antennas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. Blasting Caps and Blasting Areas Warning: To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: Turn off two-way radio. Obey all signs and instructions. Batteries rating. Charge your battery using the approved Motorola Solutions charger. Use the battery in accordance with its water and/or dust Ingress Protection (IP) Do not discard your battery into a fire. Do not replace the battery in any area labeled "Hazardous Atmosphere". Do not disassemble, crush, puncture, shred, or otherwise attempt to change the Do not dry a wet or damp battery with an appliance or heat source, such as a form of your battery. hair dryer or microwave oven. Do not allow conductive material such as jewelry, keys, or beaded chains to touch exposed battery terminals. Do not dispose of batteries with household waste. 6 English Repair Warning:

Repairs to a Motorola Solutions intrinsically safe radio product certified by, for example, FM, UL, CSA, CENELEC, should only be done at a location that has been audited under the certifying body's repair and service standard. Contact Motorola Solutions for assistance regarding repairs and service of Motorola Solutions intrinsically safe equipment. A repair constitutes something done internally to the unit that would bring it back to its original condition. Items not considered as repairs are those in which an action is performed on a unit which does not require the outer casing of the unit to be opened in a manner that exposes the internal electrical circuits of the unit. Do Not Substitute Options or Accessories The Motorola Solutions communications equipment certified as intrinsically safe by the approving agency (FM, UL, CSA, CENELEC) is tested as a complete system which consists of the listed agency Approved portable, Approved battery, and Approved accessories or options, or both. This Approved portable and battery combination must be strictly observed. There must be no substitution of items, even if the substitute has been previously Approved with a different Motorola Solutions communications equipment unit. Approved configurations are listed by the Approving Agency (FM, UL, CSA, CENELEC). The Intrinsically Safe Approval Label affixed to radio refers to the intrinsically safe classification of that radio product, and the approved batteries that can be used with that system. The manual PN referenced on the Intrinsically Safe Approval Label identifies the approved Accessories and or options that can be used with that portable radio unit. Using a non-Motorola Solutions-intrinsically safe battery and/or accessory with the Motorola Solutions approved radio unit will void the intrinsically safe approval of that radio unit. European Union (EU) Waste of Electrical and Electronic Equipment

(WEEE) Directive The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries should not dispose of 7 English electronic and electrical equipment or accessories in household waste. Customers or end-users in EU countries should contact their local equipment supplier representative or service centre for information about the waste collection system in their country. For Brazil, information for disposal and recycling of electronic waste, batteries, and packaging, please call: 0800168272. 8 Notes Cover2.fm Page 1 Wednesday, April 24, 2019 1:17 PM MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. 2012 and 2020 Motorola Solutions, Inc. All rights reserved.

*PMLN6300F*

PMLN6300F

*68012007006*

68012007006-CD

en-US RF Energy Exposure Training and Product Safety Information for Portable Two-Way Radios fr-CA Formation sur lexposition aux RF et information sur la scurit du produit pour radios bidirectionnelles portatives es-LA Capacitacin sobre la exposicin a energa de radiofrecuencia e informacin de proteccin del producto para radios de dos vas porttiles pt-BR Treinamento sobre a Exposio Energia de RF e Informaes de Segurana do Produto para Rdios Portteis Bidirecionais English Caution Before using this radio, read this booklet which contains important operating instructions. For information on product details, brochures, user manuals and approved accessories. Please refer to www.motorolasolutions.com. Compliance with RF Exposure Standards National and international regulations require manufacturers to comply with the RF energy exposure limits for portable two-way radios before they can be marketed. Your Motorola Solutions two-way radio is designed, manufactured, and tested to comply with all applicable national and international regulations for human exposure to radio frequency electromagnetic energy. When two-way radios are used as a consequence of employment, applicable regulations may require users to be fully aware of and able to control their exposure to meet occupational requirements. RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use Note: This radio is intended for use in occupational/controlled conditions where users are aware of their exposure and can exercise control over their exposure to meet the requirements in national and international regulations. This radio device is not authorized for general population, consumer use. For more information on what RF energy exposure is, and how to control your exposure to ensure compliance with established RF exposure limits, consult the following websites:

https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en http://www.who.int/peh-emf/project/en/

For additional user training information on exposure requirements, consult the following websites:

https://www.motorolasolutions.com/en_us/about/company-overview/corporate-

responsibility/governance-and-policies/wireless-communication-and-health-

faqs.html http://learning.motorolasolutions.com/

RF Exposure Compliance and Control Guidelines To control your exposure, and ensure compliance with the relevant RF exposure limits, always adhere to the following guidelines:

1 English Do not remove any of the RF Exposure Labels if present from this device or its related accessories. Attach these instructions to the device when you transfer it to other users. Do not use this device if the operational requirements described herein are not met. Operating Instructions Transmit no more than 50% of the time. To transmit (talk), press the Push-To-

Talk (PTT) button. To receive calls, release the PTT button. Transmitting more than 50% of the time may cause RF exposure compliance requirements to be exceeded. Hold the radio in a vertical position in front of the face with the microphone (and other parts of the radio including the antenna) at least 1 in. (2.5 cm) away from the nose or lips. Antenna should be kept away from the eye. When worn on the body, always place the radio in a Motorola Solutions-

approved clip, holder, holster, case, or body harness for this product. DO NOT hold the antenna when the radio is transmitting. DO NOT use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. To ensure continued compliance with applicable RF exposure limits, use only Motorola Solutions approved, supplied or replacement antennas, batteries, and accessories. For a list of Motorola Solutions approved accessories please refer to your user manual or visit www.motorolasolutions.com Acoustic Safety Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the volume of the radio, the sooner your hearing will be affected. Hearing damage from loud noise is sometimes undetectable at first, and can have a cumulative effect. To protect your hearing, follow these precautions:

Use the lowest volume necessary to do your job. Turn up the volume only if you are in noisy surroundings. Turn down the volume before putting on a headset or headphones. Limit the amount of time you use a headset or headphones at high volume. When using the radio without a headset or headphones, do not place the speaker of the radio directly against your ear. 2 English Medical Devices If you use a personal medical device, such as a pacemaker or hearing aid, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. Operational Warnings The following explains the operational warnings:

For Vehicle With Air Bags Warning:

Refer to vehicle manufacturer's manual prior to installation of electronic equipment to avoid interference with air bag wiring. DO NOT place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. Potentially Explosive Atmospheres Warning:

Use of a radio that is not intrinsically safe in a potentially explosive atmosphere could result in a serious injury or death. You should only use a certified Intrinsically Safe radio in potentially explosive atmospheres. Explosive atmospheres refer to hazard classified locations that may contain hazardous gas, vapors, dusts, such as fueling areas below decks on boats, fuel or chemical transferor storage facilities, and areas where the air contains chemicals or particles such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often, but not always, posted. Turn off your radio prior to entering any area with a potentially explosive atmosphere unless it is a radio type specifically certified for use in hazardous location areas. DO NOT remove, install, or charge batteries in such areas, or remove or install antennas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. 3 English Blasting Caps and Blasting Areas Warning: To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: Turn off two-way radio. Obey all signs and instructions. Batteries Charge your battery using the approved Motorola Solutions charger. Use the battery in accordance with its water and/or dust Ingress Protection (IP) rating. Do not discard your battery into a fire. Do not replace the battery in any area labeled "Hazardous Atmosphere". Do not disassemble, crush, puncture, shred, or otherwise attempt to change the form of your battery. Do not dry a wet or damp battery with an appliance or heat source, such as a hair dryer or microwave oven. Do not allow conductive material such as jewelry, keys, or beaded chains to touch exposed battery terminals. Repair Warning:

Repairs to a Motorola Solutions intrinsically safe radio product certified by, for example, FM, UL, CSA, CENELEC, should only be done at a location that has been audited under the certifying body's repair and service standard. Contact Motorola Solutions for assistance regarding repairs and service of Motorola Solutions intrinsically safe equipment. A repair constitutes something done internally to the unit that would bring it back to its original condition. Items not considered as repairs are those in which an action is performed on a unit which does not require the outer casing of the unit to be opened in a manner that exposes the internal electrical circuits of the unit. Do Not Substitute Options or Accessories The Motorola Solutions communications equipment certified as intrinsically safe by the approving agency (FM, UL, CSA, CENELEC) is tested as a complete system which consists of the listed agency Approved portable, Approved battery, and Approved accessories or options, or both. This Approved portable and battery combination must be strictly observed. There must be no substitution of items, even if the substitute has been previously Approved with a different Motorola Solutions 4 English communications equipment unit. Approved configurations are listed by the Approving Agency (FM, UL, CSA, CENELEC). The Intrinsically Safe Approval Label affixed to radio refers to the intrinsically safe classification of that radio product, and the approved batteries that can be used with that system. The manual PN referenced on the Intrinsically Safe Approval Label identifies the approved Accessories and or options that can be used with that portable radio unit. Using a non-Motorola Solutions-intrinsically safe battery and/or accessory with the Motorola Solutions approved radio unit will void the intrinsically safe approval of that radio unit. European Union(EU) Waste of Electrical and Electronic Equipment

(WEEE) Directive The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product (or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries should not dispose of electronic and electrical equipment or accessories in household waste. Customers or end-users in EU countries should contact their local equipment supplier representative or service centre for information about the waste collection system in their country. 5 RED_2.fm Page 5 Friday, June 23, 2017 10:11 AM Notes Portugus (Brasil) Ateno Antes de usar o rdio, leia este folheto, que contm importantes instrues de operao. Para obter informaes sobre detalhes do produto, folhetos, manuais do usurio e acessrios aprovados. Consulte www.motorolasolutions.com. Conformidade com os Padres de Exposio RF Os regulamentos nacionais e internacionais exigem que os fabricantes estejam em conformidade com os limites de exposio energia de RF para rdios portteis bidirecionais antes de serem comercializados. O rdio bidirecional da Motorola Solutions foi projetado, fabricado e testado para estar em conformidade com todos os regulamentos nacionais e internacionais para exposio de seres humanos energia eletromagntica de radiofrequncia. Ao usar rdios bidirecionais por motivos de trabalho, os regulamentos aplicveis podem exigir que os usurios estejam totalmente conscientes e aptos a controlar sua exposio de modo a atender s exigncias ocupacionais. Informaes sobre Conscientizao e Controle de Exposio Energia de RF e Instrues Operacionais para o Uso Ocupacional Comunicado: Este rdio destina-se ao uso em condies ocupacionais/

controladas, em que os usurios estejam cientes de sua exposio e possam exercer controle sobre ela, para atender aos requisitos nos regulamentos nacionais e internacionais. O uso do dispositivo de rdio pela populao em geral no autorizado. Para obter mais informaes sobre a exposio energia de RF e como controlar a exposio para garantir a conformidade com os limites de exposio RF estabelecidos, acesse os seguintes sites:

https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en http://www.who.int/peh-emf/project/en/

Para informaes adicionais de treinamento sobre os requisitos de exposio, acesse os seguintes sites:

https://www.motorolasolutions.com/en_us/about/company-overview/corporate-

responsibility/governance-and-policies/wireless-communication-and-health-

faqs.html http://learning.motorolasolutions.com/

1 Portugus (Brasil) Diretrizes de Conformidade e Controle de Exposio RF Para controlar a exposio e garantir a conformidade com os limites de exposio RF em questo, siga sempre as diretrizes a seguir:

No remova as Etiquetas de Exposio RF, se houverem, do dispositivo ou acessrios relacionados. Anexe essas instrues ao dispositivo quando o transferir a outros usurios. No use este dispositivo se os requisitos operacionais descritos aqui no forem atendidos. Instrues Operacionais Transmita, no mximo, 50% do tempo. Para transmitir (falar), pressione o boto PTT (Push-To-Talk). Para receber chamadas, solte o boto PTT (Push-To-Talk). Transmitir mais de 50% do tempo pode fazer que os requisitos de conformidade de exposio RF sejam excedidos. Segure o rdio em posio vertical em frente ao rosto com o microfone (e outras partes do rdio incluindo a antena) a pelo menos 2,5 cm (1 polegada) de distncia do nariz ou dos lbios. A antena deve ficar longe dos olhos. Ao usar o rdio junto ao corpo, sempre o coloque em um prendedor, suporte, suporte para cinto ou estojo para este produto aprovado pela Motorola Solutions. NO segure a antena enquanto o rdio estiver transmitindo. NO utilize um rdio porttil com antena danificada. Se a antena danificada entrar em contato com sua pele, poder causar uma queimadura leve. Para garantir constantemente a conformidade com os limites aplicveis de exposio RF, use apenas antenas, baterias e acessrios de reposio aprovados ou fornecidos pela Motorola Solutions. Para obter uma lista dos acessrios aprovados pela Motorola Solutions, consulte o manual do usurio ou acesse www.motorolasolutions.com Segurana Acstica A exposio a rudos muito altos de qualquer origem por longos perodos pode prejudicar sua audio temporria ou permanentemente. Quanto maior for o volume do rdio, mais cedo sua audio ser prejudicada. s vezes, os danos auditivos causados por rudos fortes no so detectados em sua fase inicial, e podem ter efeito cumulativo. Para proteger sua audio, siga estas precaues:

Use o volume mais baixo necessrio para a execuo da sua tarefa. Aumente o volume somente se estiver em ambientes barulhentos. Reduza o volume antes de colocar um headset ou fones de ouvido. 2 Portugus (Brasil) Limite o tempo de utilizao de um headset ou fones de ouvido com volume alto. Ao usar o rdio sem o headset ou fones de ouvido, no coloque o alto-falante do rdio diretamente em contato com o ouvido. Equipamentos Mdicos Se voc usa um dispositivo mdico pessoal, como um marca-passo ou aparelho auditivo, consulte o fabricante do dispositivo para determinar se est adequadamente protegido contra energia de RF. Seu mdico pode ajud-lo a obter essas informaes. Avisos Operacionais A seguir so explicados os avisos operacionais:

Para Veculos Equipados com Air Bags Aviso:

Consulte o manual do fabricante do veculo antes de instalar equipamentos eletrnicos para evitar interferncia com o funcionamento do air bag. NO coloque um rdio porttil na rea sobre um air bag ou na rea de liberao do air bag. Os air bags inflam com muita fora. Se um rdio porttil estiver posicionado na rea de abertura do air bag e ele inflar, o rdio poder ser impelido com grande fora e causar graves ferimentos aos ocupantes do veculo. Ambientes Potencialmente Explosivos Aviso:

O uso de um rdio que no intrinsecamente seguro em um ambiente potencialmente explosivo poder resultar em danos graves e at em morte. Voc deve usar apenas rdios Intrinsecamente Seguros certificados em ambientes potencialmente explosivos. Ambientes potencialmente explosivos referem-se a locais classificados como de risco que podem conter gases, vapores ou ps nocivos, como reas de abastecimento embaixo do convs principal em barcos, instalaes de armazenamento ou transferncia de produtos qumicos ou combustvel e reas onde o ar contm partculas ou elementos qumicos, como fibras, poeira ou ps metlicos. As reas com ambientes potencialmente explosivos so frequentes, mas nem sempre h avisos sobre isso. Desligue o rdio antes de entrar em qualquer rea com ambientes potencialmente explosivos, a menos que o tipo de rdio seja especificamente certificado para utilizao em reas de risco. 3 Portugus (Brasil) NO remova, instale ou carregue baterias nessas reas, nem remova ou instale antenas. Fascas em um ambiente potencialmente explosivo podem causar uma exploso ou incndio que pode resultar em ferimentos e, at mesmo, morte. reas e Equipamentos para Detonao Aviso: Para evitar possveis interferncias em operaes de detonao, desligue o rdio quando estiver prximo a detonadores eltricos, reas de detonao ou reas onde haja avisos tais como: Desligue rdios bidirecionais. Obedea a todas as sinalizaes e instrues. Baterias Sempre carregue a bateria usando o carregador aprovado pela Motorola Solutions. Use a bateria de acordo com sua classificao de Proteo contra entrada (IP) de p e gua. No descarte a bateria no fogo. No troque a bateria em lugares identificados como "Atmosferas Potencialmente Perigosas". No desmonte, comprima, perfure, fragmente nem tente alterar de outra maneira a forma da bateria. No seque baterias molhadas nem midas usando aparelhos ou fontes de calor, como secadores de cabelo ou fornos de micro-ondas. No permita que materiais condutores como joias, chaves ou correntes toquem os terminais expostos da bateria. Reparo Aviso:

Reparos em rdios intrinsecamente seguros da Motorola Solutions certificados, por exemplo, por FM, UL, CSA, CENELEC, devem ser feitos apenas em um local que passou por auditoria de acordo com as normas de reparo e manuteno dos rgos certificadores. Entre em contato com a Motorola Solutions para obter assistncia sobre reparos e servios em equipamentos Motorola Solutions intrinsecamente seguros. Um reparo constitui algo sendo feito internamente na unidade que a retornar as suas condies originais. Os itens que no so considerados como reparos so os em que a ao realizada em uma unidade que no precisa que a parte externa seja aberta para expor os circuitos eltricos internos da unidade. 4 Portugus (Brasil) No Substitua Opes ou Acessrios O equipamento de comunicao Motorola Solutions certificado como intrinsecamente seguro pelos rgos de aprovao (FM, UL, CSA, CENELEC), testado como um sistema completo que consiste do porttil aprovado, bateria aprovada e acessrios e/ou opes aprovados pelo rgo listado. Essa combinao de porttil e bateria aprovada deve ser estritamente observada. No pode haver substituio de itens, mesmo se o substituto tiver sido aprovado previamente com um equipamento de comunicaes Motorola Solutions diferente. As configuraes aprovadas so listadas pelo rgo Aprovador (FM, UL, CSA, CENELEC). A Etiqueta de Aprovao de Intrinsecamente Seguro afixada ao rdio refere-se classificao de intrinsecamente seguro do rdio e da bateria aprovada que pode ser usada com o sistema. O PN manual referenciado na Etiqueta de Aprovao de Intrinsecamente Seguro identifica os acessrios ou opes aprovados que podem ser usados com a unidade de rdio porttil. O uso de uma bateria e/ou acessrio intrinsecamente seguro no Motorola Solutions com a unidade de rdio aprovada pela Motorola Solutions invalidar a aprovao de segurana intrnseca da unidade de rdio. Diretiva de Resduos de Equipamentos Eltricos e Eletrnicos

(WEEE) para a Unio Europeia (UE) A Diretiva de WEEE da Unio Europeia exige que os produtos vendidos nos pases da UE tenham a etiqueta de lixeira riscada no produto (ou no pacote, em alguns casos). Conforme definido pela diretiva WEEE, essa etiqueta de lixeira cruzada indica que os clientes e os usurios nos pases da UE no devem descartar equipamentos ou acessrios eltricos ou eletrnicos em lixo domstico. Os clientes ou os usurios nos pases da UE devem entrar em contato com o representante local do fornecedor do equipamento ou com a central de servios para obter informaes sobre o sistema de coleta de lixo em seu pas. 5 RED_2.fm Page 5 Friday, June 23, 2017 10:11 AM Notes Franais (Canada) Mise en garde Avant d'utiliser cette radio, lisez cette brochure qui contient d'importantes consignes d'utilisation. Pour obtenir plus dinformation sur les dtails du produit, les brochures, les manuels et les accessoires approuvs : Veuillez vous reporter www.motorolasolutions.com. Conformit aux normes sur l'exposition aux radiofrquences Les rglementations nationales et internationales noncent que les fabricants de radios bidirectionnelles portatives doivent sassurer que celles-ci sont conformes aux limites dexposition l'nergie RF avant de les commercialiser. Cette radio bidirectionnelle Motorola Solutions a t conue, fabrique et teste afin de garantir sa conformit aux normes nationales et internationales lies l'exposition des tres humains l'nergie lectromagntique de radiofrquence. Lorsque les radios bidirectionnelles sont utilises des fins professionnelles, la rglementation en vigueur exige que les utilisateurs soient pleinement conscients des effets de l'exposition et qu'ils soient capables de contrler le niveau d'exposition auquel ils se soumettent afin de rpondre aux exigences de leur profession. Information de sensibilisation et de gestion de l'exposition l'nergie RF, et consignes pour l'usage professionnel Avis: Cette radio a t conue pour un usage professionnel dans un environnement contrl, o les utilisateurs sont pleinement conscients de l'exposition l'nergie RF laquelle ils sont soumis et peuvent exercer un contrle sur cette exposition afin de respecter les limites tablies par les rglements nationaux et internationaux. Ce dispositif radio n'est pas autoris pour l'utilisation grand public par des consommateurs ordinaires. Visitez les sites Web suivants pour obtenir plus de renseignements sur ce qu'est l'nergie RF et sur les moyens de contrle prendre afin de respecter les limites tablies en matire d'exposition aux radiofrquences. https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en http://www.who.int/peh-emf/project/en/

Pour plus de renseignements sur la formation des utilisateurs relativement aux limites d'exposition, consultez les sites suivants :

https://www.motorolasolutions.com/en_us/about/company-overview/corporate-

responsibility/governance-and-policies/wireless-communication-and-health-

faqs.html http://learning.motorolasolutions.com/

1 Franais (Canada) Directives de conformit et de contrle de l'exposition aux RF Pour contrler votre exposition et garantir le respect des limites d'exposition applicables, observez toujours les consignes suivantes. Ne pas retirer les tiquettes relatives l'exposition aux RF qui sont apposes sur cet appareil ou sur ses accessoires. Joignez ces directives l'appareil lorsque vous le transfrez d'autres utilisateurs. N'utilisez pas cet appareil si les conditions de fonctionnement dcrites aux prsentes ne sont pas runies. Consignes dutilisation Ne pas mettre plus de 50 % du temps. Pour transmettre (parler), appuyez sur le bouton Push-to-talk (PTT). Pour recevoir les appels, relchez le bouton PTT. Le fait de transmettre plus de 50 % du temps peut entraner le dpassement de la limite dexposition normalise au rayonnement RF. Tenez la radio la verticale devant le visage, en maintenant une distance dau moins 2,5 centimtres (1 pouce) entre le micro (et les autres parties de la radio, y compris lantenne) et le nez ou les lvres. Lantenne doit tre maintenue loin des yeux. Lorsque vous portez la radio sur vous, fixez-la toujours avec une pince ou une attache de ceinture et placez-la dans un tui ou un harnais approuv par Motorola Solutions pour l'utilisation avec ce produit. NE TENEZ PAS lantenne entre vos doigts pendant que la radio met. N'UTILISEZ PAS une radio portative, quelle quelle soit, dont lantenne est endommage. Si une antenne endommage entre en contact avec votre peau, il peut en rsulter une brlure lgre. Pour assurer la conformit continue avec les limites d'exposition aux RF applicables, utilisez uniquement les antennes, les batteries et les accessoires de remplacement ou fournis et approuvs par Motorola Solutions. Pour obtenir une liste des accessoires approuvs par Motorola Solutions, veuillez consulter votre manuel ou visitez le site www.motorolasolutions.com Protection de l'oue Une exposition des bruits forts en provenance de n'importe quelle source pendant de longues priodes pourrait affecter votre audition de manire temporaire ou permanente. Plus le volume de la radio est lev, plus le dommage pour l'oue survient rapidement. Des dommages auditifs dus l'exposition des bruits forts peuvent ne pas tre dcels immdiatement, mais leurs effets sont parfois cumulatifs. Pour protger votre oue, suivez ces instructions:

2 Franais (Canada) Rglez le volume le plus bas possible pour effectuer votre travail. Montez le volume seulement si vous vous trouvez dans un environnement bruyant. Baissez le volume avant d'ajouter un casque ou un couteur. Limitez la dure d'utilisation de votre casque ou de votre couteur un volume lev. Lorsque vous utilisez la radio sans casque ni couteur, ne placez pas le haut-

parleur de la radio directement sur votre oreille. Appareils mdicaux Si vous utilisez un dispositif mdical personnel, comme un stimulateur cardiaque ou une prothse auditive, consultez le fabricant de votre appareil pour dterminer s'il est convenablement protg contre les RF. Votre mdecin peut vous aider obtenir ces renseignements. Avertissements de fonctionnement Le tableau suivant explique les avertissements de fonctionnement :

Pour vhicules quips de coussins gonflables Avertissement:

Consultez le manuel du fabricant du vhicule avant d'installer un appareil lectronique, afin d'viter toute interfrence avec le cblage des coussins gonflables. NE PLACEZ PAS de radio portative dans la zone situe au-dessus d'un coussin gonflable ou dans la zone de dploiement de ce dernier. Un coussin gonflable de scurit se dploie avec beaucoup de force. Si une radio portative se trouve dans la zone de dploiement du coussin, lorsque celui-ci se gonfle, la radio peut tre propulse avec une force considrable et risque alors d'occasionner de graves lsions corporelles aux passagers du vhicule. Atmosphres potentiellement explosives Avertissement:

L'utilisation d'une radio autre qu'une radio scurit intrinsque dans une atmosphre potentiellement explosive est susceptible d'entraner des blessures graves ou la mort. Vous ne devez pas utiliser de radio de scurit intrinsque agre dans des atmosphres potentiellement explosives. On retrouve des atmosphres explosives dans les lieux classs comme tant dangereux en raison de la prsence de gaz, de vapeurs et de poussires reprsentant un danger, par exemple, les zones 3 Franais (Canada) d'avitaillement en carburant dans des cales de bateau, les installations de transfert et de stockage de carburant ou de produits chimiques, et les zones dans lesquelles l'air est charg en produits chimiques ou en particules telles que de la poudre de crales, de la poussire ou de la poudre mtallique. Les zones atmosphres potentiellement explosives affichent gnralement des panneaux de mise en garde, mais ce n'est pas toujours le cas. teignez la radio avant d'accder un lieu prsentant une atmosphre potentiellement explosive, moins qu'il s'agisse d'un type de radio certifi spcifiquement pour une utilisation dans des zones dangereuses. VITEZ d'enlever, d'installer ou de charger les batteries, ou d'enlever ou d'installer des antennes dans de tels lieux. Les tincelles dans des atmosphres potentiellement explosives peuvent provoquer une explosion ou un incendie et entraner des lsions corporelles, voire la mort. Zone de dynamitage et dtonateurs Avertissement: teignez la radio lorsque vous vous trouvez proximit de dtonateurs lectriques ou dans une zone de dynamitage afin dviter de dclencher une explosion, ou lorsque vous vous trouvez dans un endroit o il est indiqu : teindre les radios bidirectionnelles . Respectez tous les panneaux et toutes les consignes. Batteries Chargez votre batterie l'aide du chargeur approuv par Motorola Solutions. Utilisez la batterie conformment son indice de protection (IP) contre l'eau et la poussire. Ne jetez pas votre batterie au feu. Ne remplacez pas la batterie dans un endroit qui porte la mention atmosphre dangereuse . Veillez ne pas dmonter, craser, percer, dcouper ou autrement modifier la forme de votre batterie. Ne faites pas scher une batterie mouille ou humide avec un appareil lectrique ou une source de chaleur, comme un schoir cheveux ou un four micro-

ondes. Ne permettez pas des matriaux conducteurs, comme des bijoux, des cls ou des mailles de chane dentrer en contact avec les bornes de la batterie. 4 Franais (Canada) Rparation Avertissement:

La rparation d'une radio de scurit intrinsque de Motorola Solutions homologue, notamment, par FM, UL, CSA ou CENELEC, doit tre effectue uniquement un endroit ayant fait l'objet d'une vrification en vertu de la norme sur les rparations et l'entretien de l'organisme de certification. Contactez Motorola Solutions afin d'obtenir de l'assistance pour l'entretien et la rparation d'une unit Motorola Solutions scurit intrinsque. Le terme rparation dsigne tout travail effectu sur les composants internes de l'unit afin de la ramener son tat d'origine. Un travail qui ne ncessite pas l'ouverture du botier de l'unit afin d'en exposer les circuits lectriques internes ne constitue pas une rparation. vitez de substituer des options ou des accessoires. L'quipement de communications Motorola Solutions certifi de scurit intrinsque par l'entit d'homologation (FMRC, UL, CSA, CENELEC) est test en tant que systme complet, savoir : la radio portative, la batterie, les accessoires et les options, tous agrs par l'entit correspondante. L'intgrit de cette configuration forme d'une radio portative et d'une batterie agres doit tre strictement respecte. Aucune substitution d'lment n'est permise, mme si l'lment de remplacement a pralablement t agr pour une autre unit de communication Motorola Solutions. Les configurations agres peuvent tre consultes dans la liste mise disposition par l'entit d'homologation (FMRC, UL, CSA, CENELEC). L'tiquette d'homologation de scurit intrinsque appose sur la radio identifie la classification de scurit intrinsque de cette radio ainsi que les batteries agres qui peuvent tre utilises avec ce systme. Le numro de rfrence du manuel mentionn sur l'tiquette d'homologation de scurit intrinsque identifie les accessoires et/ou les options agrs qui peuvent tre utiliss avec cette unit de radio portative. Le fait de ne pas utiliser une batterie ou un accessoire Motorola Solutions de scurit intrinsque avec l'unit de radio Motorola Solutions agre annule l'homologation de scurit intrinsque de cette unit de radio. Directive sur la mise au rebut des quipements lectriques et lectroniques de l'Union europenne (UE) (WEEE) La directive WEEE de l'Union europenne exige que les produits vendus dans les pays de l'UE portent l'tiquette de la poubelle barre (ou leur emballage, dans 5 Franais (Canada) certains cas). Comme le dfinit la directive WEEE, cette tiquette de poubelle barre signifie que les clients et les utilisateurs finaux dans les pays de l'UE ne doivent pas jeter les quipements lectriques et lectroniques ou leurs accessoires dans les ordures domestiques. Les clients ou les utilisateurs finaux dans les pays de l'UE doivent communiquer avec le reprsentant ou le centre de service de leur fournisseur d'quipement pour obtenir des renseignements sur le systme de collecte des dchets de leur pays. 6 Espaol (Latinoamrica) Precaucin Antes de usar este radio, lea el folleto que contiene instrucciones de funcionamiento importantes. Para obtener informacin sobre los detalles del producto, folletos, manuales de usuario y accesorios aprobados, consulte www.motorolasolutions.com. Conformidad con las normas sobre exposicin a la radiofrecuencia Las regulaciones nacionales e internacionales obligan a que los fabricantes cumplan con los lmites de exposicin a energa de radiofrecuencia para radios mviles de dos vas antes de que se puedan comercializar. El radio de dos vas Motorola Solutions est diseado, fabricado y probado para cumplir con todas las regulaciones nacionales e internacionales correspondientes en materia de exposicin humana a la energa electromagntica de radiofrecuencia. Cuando los radios de dos vas se usan para trabajar, las regulaciones correspondientes podran exigir que los usuarios conozcan y controlen su nivel de exposicin para cumplir con los requisitos de uso profesional. Conocimiento de la exposicin a energa de radiofrecuencia, informacin de control e instrucciones de funcionamiento para uso ocupacional Nota: Este radio est diseado para usarse en condiciones controladas o profesionales, donde los usuarios tengan pleno conocimiento de su exposicin y puedan controlarla con el fin de cumplir con los requisitos de las regulaciones nacionales e internacionales. Este dispositivo de radio no est autorizado para el uso particular de la poblacin en general. Para obtener ms informacin sobre el significado de la exposicin a energa de radiofrecuencia y cmo controlar la exposicin con el fin de asegurar el cumplimiento de los lmites de exposicin a radiofrecuencias establecidos, consulte los siguientes sitios web:

https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en http://www.who.int/peh-emf/project/en/

Para obtener informacin adicional de la capacitacin de los usuarios sobre los requisitos de exposicin, consulte los siguientes sitios web:

https://www.motorolasolutions.com/en_us/about/company-overview/corporate-

responsibility/governance-and-policies/wireless-communication-and-health-

faqs.html 1 Espaol (Latinoamrica) http://learning.motorolasolutions.com/

Cumplimiento de exposicin a radiofrecuencia y pautas de control Para controlar la exposicin y garantizar el cumplimiento de los lmites de exposicin a radiofrecuencias correspondientes, respete siempre las siguientes pautas:

No retire ninguna de las etiquetas de exposicin a radiofrecuencias, si las hubiere, de este dispositivo o sus accesorios respectivos. Adjunte estas instrucciones al dispositivo cuando se lo transfiera a otros usuarios. No utilice este dispositivo si no se cumple con los requisitos de funcionamiento descritos en este documento. Instrucciones de funcionamiento No transmita ms de un 50 % del tiempo. Para transmitir (hablar), presione el botn Push to Talk (PTT). Para recibir llamadas, suelte el botn PTT. Una transmisin superior al 50 % del tiempo de uso podra provocar que se superen los requisitos de cumplimiento de exposicin a radiofrecuencia. Sostenga el radio en posicin vertical frente a su rostro con el micrfono (y otras partes del radio, incluida la antena) al menos a 1 pulgada (2,5 cm) de distancia de la nariz o los labios. Mantenga la antena alejada de los ojos. Siempre que use el radio ajustado al cuerpo, pngalo en un clip, un soporte, un estuche, una funda o un arns para el cuerpo aprobado por Motorola Solutions para este producto. NO sujete la antena mientras el radio est realizando una transmisin. No utilice radios porttiles que tengan la antena daada. Si una antena daada toca su piel, puede causar una pequea quemadura. Para garantizar el cumplimiento continuo de los lmites de exposicin a radiofrecuencia correspondientes, utilice solamente las antenas, las bateras y los accesorios de repuesto suministrados o aprobados por Motorola Solutions. Para obtener una lista de los accesorios aprobados por Motorola Solutions, consulte el manual del usuario o visite www.motorolasolutions.com. Seguridad acstica La exposicin a ruidos fuertes de cualquier fuente durante perodos prolongados podra afectar la audicin de manera temporal o permanente. Cuanto ms alto sea el volumen del radio, ms rpido se ver afectada la audicin. En ocasiones, el dao a la audicin provocado por ruidos fuertes es indetectable en un principio y puede tener efecto acumulativo. Para proteger la audicin, siga estas precauciones:

2 Espaol (Latinoamrica) Utilice el volumen ms bajo que necesite para hacer su trabajo. Aumente el volumen solo si se encuentra en un ambiente ruidoso. Reduzca el volumen antes de conectar auriculares o audfonos. Limite el tiempo durante el cual utiliza auriculares o audfonos a volumen alto. Cuando use el radio sin auriculares o audfonos, no coloque el altavoz del radio directamente en la oreja. Aparatos mdicos Si utiliza un dispositivo mdico, como un marcapasos o una prtesis auditiva, consulte al fabricante del dispositivo para determinar si est adecuadamente protegido contra las energas de radiofrecuencia. Su mdico podra ayudarlo a obtener esta informacin. Advertencias de funcionamiento A continuacin, se explican las advertencias de funcionamiento:

Para vehculos con airbags Advertencia:

Consulte el manual del fabricante del vehculo antes de instalar equipos electrnicos, a fin de evitar la interferencia con el cableado de las bolsas de aire. NO coloque el radio porttil sobre una bolsa de aire ni en el rea de despliegue de la bolsa. Las bolsas de aire se inflan con mucha fuerza. Si se pone un radio porttil en el rea de despliegue de la bolsa de aire y esta se infla, es posible que el radio salga disparado con gran fuerza y cause lesiones graves a los ocupantes del vehculo. Atmsferas potencialmente explosivas Advertencia:

El uso de un radio que no sea intrnsecamente seguro en una atmsfera potencialmente explosiva puede provocar lesiones graves o la muerte. En atmsferas potencialmente explosivas, debe utilizar solamente un radio intrnsecamente seguro certificado. El trmino atmsferas explosivas se refiere a lugares clasificados como peligrosos en los que podra haber gases, vapores o polvos peligrosos, como reas con combustibles bajo las cubiertas de los botes o instalaciones de almacenamiento o transferencia de qumicos, y reas en que el aire contenga productos qumicos o partculas, como material granulado, polvo o polvo metlico. En las reas con atmsferas potencialmente explosivas generalmente hay seales de precaucin, aunque no siempre es as. 3 Espaol (Latinoamrica) Apague el radio antes de ingresar a cualquier rea que posea una atmsfera potencialmente explosiva, a menos que se trate de un tipo de radio certificado especficamente para ser usado en zonas de ubicaciones peligrosas. NO retire, instale ni cargue bateras, ni tampoco retire o instale antenas en dichas reas. Las chispas en ambientes potencialmente explosivos pueden desencadenar una explosin o un incendio, y ocasionar lesiones o incluso la muerte. reas de voladuras y explosivos Advertencia: Para evitar posibles interferencias con operaciones de voladuras, apague el radio cuando se encuentre cerca de zonas de voladuras elctricas, en un rea de explosivos o en reas donde se encuentre el siguiente aviso: Apague el radio de dos vas. Obedezca todas las seales e instrucciones. Bateras Cargue la batera con cargadores aprobados por Motorola Solutions. Utilice la batera de acuerdo con su clasificacin de proteccin de ingreso (IP) contra polvo y agua. No arroje la batera al fuego. No cambie la batera en un rea designada como Atmsfera peligrosa. No desarme, rompa, perfore, triture ni intente cambiar de ningn otro modo la forma de la batera. No intente secar una batera mojada o hmeda con un electrodomstico o una fuente de calor externa, como un secador de pelo o un horno microondas. No permita que materiales conductores como joyas, llaves o cadenas hagan contacto con los terminales expuestos de la batera. Reparacin Advertencia:

Las reparaciones de productos de un radio Motorola Solutions intrnsecamente seguro certificado, por ejemplo, FM, UL, CSA, CENELEC, deben realizarse solo en una ubicacin que haya sido auditada segn el estndar de reparacin y servicio de la entidad certificante. Comunquese con Motorola Solutions para solicitar asistencia relacionada con reparaciones y tareas de servicio de los equipos Motorola Solutions intrnsecamente seguros. Una reparacin consta de algo hecho en el interior de la unidad que debe devolverla a su estado original. 4 Espaol (Latinoamrica) Las instancias que no se consideran reparaciones son las que incluyen una accin realizada en una unidad que no requiere que la cubierta externa se abra de manera tal que queden expuestos los circuitos elctricos de la unidad. No sustituya los elementos opcionales ni los accesorios Los equipos de comunicaciones de Motorola Solutions que cuentan con un certificado que indica que son intrnsecamente seguros, emitido por una agencia de aprobacin (FM, UL, CSA, CENELEC), se prueban como sistemas completos que incluyen: el dispositivo porttil aprobado, la batera aprobada y los accesorios o los elementos opcionales aprobados, o ambos. Debe respetar de manera estricta esta combinacin de dispositivo porttil y batera aprobada. No se deben sustituir los elementos, aun si la pieza de sustitucin se prob anteriormente para otro equipo de comunicaciones Motorola Solutions. Las configuraciones aprobadas son detalladas por la agencia de aprobacin (FM, UL, CSA, CENELEC). La etiqueta de aprobacin como intrnsecamente seguro adherida al radio indica la clasificacin de intrnsecamente seguro de ese radio e indica las bateras aprobadas que pueden usarse con ese sistema. La etiqueta de aprobacin de intrnsecamente seguro adherida al radio hace referencia a un nmero de pieza del manual que indica los accesorios o los elementos opcionales que se pueden usar con la unidad de radio porttil. El uso de una batera o un accesorio aprobado como intrnsecamente seguro que no sea de Motorola Solutions con el radio Motorola Solutions aprobado anular la aprobacin de intrnsecamente seguro de esa unidad de radio. Directiva de Residuos de Aparatos Elctricos y Electrnicos

(RAEE) de la Unin Europea (UE) La Directiva RAEE de la Unin Europea requiere que los productos que se venden en los pases de la UE tengan la etiqueta de un bote de residuos tachado sobre el producto (o en el paquete, en algunos casos). Como define la directiva RAEE, esta etiqueta con un bote de basura tachado indica que los clientes y los usuarios finales en los pases de la UE no deben deshacerse de los equipos o accesorios elctricos y electrnicos con la basura domstica. Los clientes o los usuarios finales en los pases de la UE deben ponerse en contacto con su representante distribuidor de equipos o el centro de servicio locales para obtener informacin sobre el sistema de recoleccin de residuos de su pas. 5 MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. 2007 and 2017 Motorola Solutions, Inc. All rights reserved. Printed in

*NNTN7223J*

NNTN7223J

*6881095C98*

6881095C98-LB

Applicant: Motorola Solutions Inc FCC ID: AZ489FT7111 / IC: 109U-89FT7111

(Pursuant to FCC Part 2.1033(c)(11), 2.1033(b)(7) and RSP 100 Annex C and Sec 3) EXHIBIT 1 IDENTIFICATION LABEL See the Attached Photograph or Sketch Bottom of Radio Top of Radio Back of Radio Back of Radio under Belt Clip X The label is a polyester film laminate with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with the minimum peel strength of 40 oz/inch. See the Attached Photograph and Exhibit 3 for the actual location of the FCC/IC label on the device. X Label Attached Below. See Attached Drawing. LOCATION X TYPE MARKINGS (TEXT) X EXHIBIT 1 SHEET 1 OF 4 Applicant: Motorola Solutions Inc FCC ID: AZ489FT7111 / IC: 109U-89FT7111 Figure 1A: FCC/IC Label for APX 8000H Model 3.5 (Full Keypad) (Existing) Figure 1B: FCC/IC Label for APX 8000H Model 2.5 (Limited Keypad) (Existing) EXHIBIT 1 SHEET 2 OF 4 Applicant: Motorola Solutions Inc FCC ID: AZ489FT7111 / IC: 109U-89FT7111 EXHIBIT 1 SHEET 3 OF 4 Figure 1C: FCC/IC Label for APX 8000HXE Model 3.5 (Full Keypad) (Existing) Figure 1D: FCC/IC Label for APX 8000HXE Model 2.5 (Limited Keypad) (Existing) Applicant: Motorola Solutions Inc FCC ID: AZ489FT7111 / IC: 109U-89FT7111 Figure 1E: FCC/IC Label for APX 8000HXE Model 1.5 (No Keypad) (New) EXHIBIT 1 SHEET 4 OF 4

Certification Department Date: 20 January 2022 Subject: Application Authorization for FCC/IC filing To Whom It May Concern:

I hereby authorize Arine Lee to apply, on my behalf, the application for the following FCC/IC ID:

FCC/IC ID: AZ489FT7111 / 109U-89FT7111 Please contact me if there are any questions or issues. Regards, Deanna Zakharia Regulatory Compliance Manager Tel: (954) 723 4707 Email: Deanna.zakharia@motorolasolutions.com ____________________________________________________________________________ Motorola Solutions Inc, 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322

Declaration Date: January 18, 2022 This WLAN/Bluetooth is a WLAN/Bluetooth combination antenna with FCC/IC To whom it may concern, ID:

This AZ489FT7111/109U-89FT7111. co-existence mechanism is to ensure that the WLAN and Bluetooth transmitters would not simultaneously operate. Therefore, WLAN and Bluetooth antenna in FCC/IC ID: AZ489FT7111/109U-89FT7111 should not be considered to be able to transmit simultaneously. Though the users can use WLAN and Bluetooth simultaneously, but the real situation is that WLAN and Bluetooth are used by time sharing and no overlap transmission. Should you have any question, please have my best attention. Sincerely yours,

Name: Afiq Jamani Title: Engineering Manager E-mail: afiq.jamani@motorolasolutions.com

FCC ID: AZ489FT7111 Date: January 21, 2022 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for Class 2 Permissive Change to FCC Authorized Transceiver with FCC ID:

AZ489FT7111 Dear Sir/Madam, A permissive change is requested for the subject transceiver which is marketed in the United States and elsewhere. A. DESCRIPTION OF PRODUCT CHANGES:

1) Replacing the current WLAN/BT IC and its supporting circuitries with new replacement and supporting design optimization circuitries. The components changes are made within the Bluetooth (BT)/ WLAN circuitries as below:

i) BT/WLAN chipset for BT/WLAN functionality from NXP IC001201A01 has 2 Vendor P/N Semiconductor and 88W8987-A2-EAH2E005-P123 from Marvell Semiconductor. Both Vendor P/N are referring to the same chipset/part. Marvell BT/Wifi business was acquired by NXP. Inclusion of 38.4MHz temperature compensated crystal oscillator (TCXO) for BT/WLAN IC reference clock listed; 88W8987-A2-EAHE/AZ ii) iii) BT/WLAN bandpass filter (passive component) change to cater for new BT/WLAN IC requirement iv) Value change on the passive components (capacitors, resistors and inductors) 2) Replacing the components on the controller section (non RF) to support the WLAN/BT IC changes. The changes are as below:

Inclusion of PM823HN PMIC for power management 3.3V LDO change to cater for new BT/WLAN IC requirement 3.6V Switching Regulator change to cater for new BT/WLAN IC requirement i) ii) iii) iv) Value change on the passive components (capacitors, resistors and inductors) 3) Added as dual source with the existing parts due to multiple supply constraints with the current parts lead time increased to 99 weeks which causing immediate line down. There is no change to the radio electrically and the replacement parts are pin-to-pin comparable with the current parts. Old Part Number New Part Number Description Where Used 4870370A72 CR001795A01 5109522E84 LD000335A01 Zener Diode

(Non RF) Buffer (Non RF) Controller Connector, as a buffer Peripheral GCAI circuit (VBUS), as a switch ________________________________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13A 5103535B53 LD000329A01 51009345001 LD000331A01 B. PERFORMANCE DIFFERENCES:

Inverter (Non RF) NOR Gate (Non RF) FCC ID: AZ489FT7111 Controller GCAI schematic, a logic inverter Controller Low Frequency pairing circuit, as a logic gate SAR degradation is observed in EME compared to the previous filing but still within the FCC limits. There is no degradation observed on EMC for LMR and BTLE, except BT and WIFI 2.4GHz have degraded as compared to the previous filing but the data continues to be compliant to the FCC limits. This radio continues to meet all FCC requirements for which authorization was granted, thus this change does meet requirements of a Class-2 Permissive Change. C. CONCLUSION:

Sincerely, _____________ Arine Lee FCC/IC Certification Manager E-mail : arinelee@motorolasolutions.com ________________________________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13A

FCC ID: AZ489FT7111 Date: January 21, 2022 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Class II Permissive Change for PCB and Part Modification and PAG C2PCPX Dear Sir/Madam, With reference to the C2PCPX procedure subject to PAG approval (item C2PCPX in KDB Publication 388624 D02) and KDB inquiry #144531, the application shall meet the following conditions:

1) The requirements of 2.1043 are fulfilled, i.e., devices block functions for the fundamental frequency, primary modulator circuit, maximum power or field strength ratings shall remain unchanged. Overall block diagram maintained no changes to primary modulator circuit, maximum power or field strength ratings. 2) Transmitter PCB layout and parts changes are only permitted if there is no change in the identification of a devices form, functional specification, as initially granted, or previously approved under a Class II permissive change. No change in terms of layout and functional specification. 3) PCB changes are limited to non-substantive modifications layout changes to the same size physical circuit board previously granted. Yes. PCB stack up, form factor and material are maintained. 4) C2PCPX is not permitted to add, remove, augment, or change capabilities, such as transmitters, increased bandwidth, additional rule parts, bands, etc. There are no addition or removal in the transmitter capabilities, bandwidth or rules part. 5) In the PAG submission for item C2PCPX, the applicant shall provide complete information on testing demonstrating that the proposed changes for fundamental emissions are unchanged within the normal acceptable tolerances and out band emissions do not exceed the appropriate limits. The PAG submission shall include all applicable test reports and internal photos. The test reports and internal photos are provided in the application. 6) The modified device shall not be marketed under the existing grant of certification before confirmation that the C2PCPX PAG is approved and granted. Yes. 7) Software Defined Radio (SDR) grants that use the C2PCPX procedure are not permitted to make subsequent Class III permissive changes. Software Defined Radio (SDR) is not used for this application. 8) The C2PCPX PAG procedure has no impact on the provisions of V) of this publication for nonSDR software-only changes, thus adding an equipment class when related to rule changes is still permitted. There is no addition of equipment class. 9) Class I permissive changes are not permitted under this C2PCPX procedure. Yes, Class I permissive changes were not performed ___________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13D FCC ID: AZ489FT7111 Sincerely, __________ Arine Lee FCC/IC Certification Manager E-mail: arinelee@motorolasolutions.com ___________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13D

FCC ID: AZ489FT7111 CONFIDENTIALITY REQUEST Date: January 21, 2022 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request for Transmitter with FCC ID: AZ489FT7111 Dear Sir / Madam, Motorola Solutions Malaysia Sdn Bhd is requesting that Exhibit 4 (Block Diagram), Exhibit 5

(Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12

(Operational Description) not be made routinely available for public inspection. Motorola Solutions considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d), 0.459 and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as Confidential. Please contact me if you require any additional information. Sincerely, Arine Lee FCC/IC Certifcation Manager E-mail: arinelee@motorolasolutions.com __________________________________________________________________________________________________________________________ Motorola Solutions Malaysia Sdn Bhd, Plot 2A, Medan Bayan Lepas, Mukim 12 SWD, 11900 Bayan Lepas, Penang, Malaysia EXHIBIT 13B

Applicant: Motorola Solutions Inc FCC ID: AZ489FT7111/ IC: 109U-89FT7111 EXHIBIT 2 Statement of Certification

(Pursuant to FCC Part 2.907, 2.908 and RSP 100 Sec 4) 2.1 Statement of Certification Transceiver type described herein (AZ489FT7111/109U-89FT7111) is in compliance with all applicable parts of the FCC rules and ISED RSS standards. This device is P25 Compliant as well which meets FCC Part 90.548 and RSS 119 Section 5.11 as declared in exhibit 12. Each unit manufactured, imported, or marketed will conform to the samples tested herein, within the statistical variations that can be expected due to high volume production and test measurement error. NAME:

Afiq Jamani SIGNATURE:

DATE:

18th January 2022 TITLE:

Engineering Manager EXHIBIT 2 SHEET 1 OF 2 Applicant: Motorola Solutions Inc FCC ID: AZ489FT7111/ IC: 109U-89FT7111 2.2 Attestation Statement (Equipment Class DTS and DSS Bluetooth/WiFi) This device contains an embedded Bluetooth device and WiFi device that are compliant with the applicable FCC Part 15C and ISED RSS 247 regulations. Part 15.247 (a)(1) / RSS 247 Section 5.1 The hopping sequence must be pseudo random. Each frequency must be used equally on the average by each transmitter The receivers input bandwidth is approximately equal to the transmit bandwidth The receiver hops in sequence with the transmitted signal Part 15.247 (g) / RSS 247 Section 5.1 The system is designed to comply with all of the regulations in this section when the transmitter is presented with a continuous data (or information) Part 15.247(h) / RSS 247 Section 5.1 The system does not coordinate its channel selection/hopping sequence with other frequency hopping systems for the express purpose of avoiding the simultaneous occupancy of individual hopping frequencies by multiple transmitters. NAME:

Muhammad Aiman Ismail SIGNATURE:

DATE:

TITLE:

18th January 2022 Electrical Engineer EXHIBIT 2 SHEET 2 OF 2

Date: January 18, 2022 that the device, FCC Declaration ID:

Inc., declare We, Motorola Solutions, AZ489FT7111, does not support any non-US channels in all the operational mode(s) in the US market. All non-US frequencies, US 2.4G channel 12-13 and Country code selection are disabled through proprietary software and are not user changeable. Should you have any question or comment regarding this matter, please do not hesitate to contact me. Sincerely yours,

Name: Afiq Jamani Title: Engineering Manager E-mail: afiq.jamani@motorolasolutions.com

FCC ID: AZ489F FT7111 er 15, 2020 Engineering a ry Division nt Authorizatio Communicatio kland Mills Ro

, MD 21046 and Technolo gy on Branch ons Commissi oad ion Laborator ry APPLICATIO ID: AZ489FT ON FOR CLAS T7111 APX80 SS 2 PERMIS 000H ALL BAN SSIVE CHAN ND (7/800, VH GE TO FCC A HF, UHF) PO ORTABLE AUTHORIZE D Transceive er Madam, sive change is er) which is m s requested fo marketed in th or APX8000H e United Stat H ALL BAND tes and elsew where.

(7/800, VHF, UHF) Portab ble (the subjec ct RIPTION OF PRODUCT C CHANGES:

T co pa he subject tra omponent cha assive compo ansceiver has anges are ma onents in the s an existing p ade within Tra LMR section. part replacem ansmitter, Re

. There is no ment due to En ceiver and DC change to the nd of Life (EO C supply sect e radio electri OL) which the tion, which ar ically. re all here is an os T Unit (FGU) in t U pin-to-

has th no cha cillator chipse the LMR sect

-pin compatib e same basic ange in radio et and VCO m ion. There is le c function as t parameters (

the previous c electrically id chip entical) module replac no change to cement made o the radio ele within Frequ ectrically. The ency Generat e changes are tion e:-

FORMANCE D DIFFERENCE ES:

MC has been ons were eval no impact to B assessed an uated and tha BT/WIFI perfo nd no degrada at the worst c ormance due ation found. In case performa to no change n the EMC re ance is presen es were involv eport, all chan nted in the re ved on these s nnels and port. sections. CLUSION:

o continues to o meet all FCC C emissions r requirements for which aut thorization wa as granted. Zakharia ry Compliance Deanna.zakha e Manager aria@motorola asolutions.co m ______________ olutions Inc. 8000 ______________ 0 West Sunrise B ______________ Boulevard, Fort L _____________ Lauderdale, Florid ______________ da 33322 ______________ ______________ EXHIBIT 13A ______ Decembe Office of E Laborator Equipmen Federal C 7435 Oak Columbia Subject: A with FCC Dear Sir/M A permiss transceive A. DESCR B. PERF EME & EM modulatio There is n C. CONC This radio Sincerely,

, Deanna Z Regulator E-mail : D __________ Motorola So

FCC ID: AZ489FT7111 December 10, 2020 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch, FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification for Certification of Transmitter with FCC ID: AZ489FT7111. Dear Sir/Madam:

This transmitter was designed to operate in the following frequency ranges:

Band / Mode VHF UHF 700 800 Bluetooth WiFi Frequency ranges 136 174 MHz 380 520 MHz 762-776 MHz, 792-806 MHz 806-825 MHz, 851-870 MHz 2402-2480 MHz 2400 2483.5 MHz FCC rule parts 22, 74, 80, 90 22, 74, 80, 90 90 90 15C 15C To aid equipment authorization in other countries which accept the United States FCC Grant for Certification, Motorola Solutions is requesting that the FCC lists the above applicable frequencies range under FCC Rule Parts 22, 74, 80, and 90 on the FCC Grant. For the FCCs Rule Parts 22, 74, 80 and 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e) and 80.203(b), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCCs KDB634817 guidance, as an alternative to listing the exact frequencies, we acknowledge that its a violation of the FCC Rules if this device operates on unauthorized frequencies. Part 22 Part 74 Part 80 Part 90 Federal Other Regions Frequency Range

(MHz) 136-150.8*

150.8-152.855 152.855-154 154-156.2475 156.2475-157.1875 157.1875-157.45 157.45-161.575 161.575-161.625 161.625-161-775 161.775-161.9625 161.9625-162.025 162.025-162.0375*

162.0375-173.4 173.4-174*

380-406.1 406.1-450 450-454 454-456 456-460 460-462.5375 462.5375-462.7375*

462.7375-467.5375 x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x x _________________________________________________________________________________________________ Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 EXHIBIT 13C 467.5375-46 467.7375 470-5 512-52 762-76 768-76 769-77 775-77 792-79 798-79 799-80 805-80 806-80 809-82 824-82 851-85 854-86 869-87 67.7375 5-470 12 20 68 69*

75 76*

98 99*

05 06*

09 24 25 54 69 70

* Canada x x x x x x x x x x x x FCC FT7111 C ID: AZ489F x x x x x x x x x x x x x x x x x x x Please con Sincerely, ntact me if you required any a additional inform mation. Deanna Za Regulatory E-mail: De akharia y Compliance M anna.zakharia@

Manager

@motorolasolu utions.com _________ Motorola So ____________ olutions Inc. 8000 _____________ 0 West Sunrise B ____________ Boulevard, Fort L _____________ Lauderdale, Florid ____________ da 33322 _____________ ____________ _________ E EXHIBIT 13C