all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
DRAFT RF SAFETY BOOKLET | Users Manual | 796.36 KiB | August 11 2005 / July 11 2005 | |||
1 2 |
|
USERS MANUAL | Users Manual | 2.86 MiB | August 11 2005 / July 11 2005 | |||
1 2 | Cover Letter(s) | June 04 2007 | ||||||
1 2 | Attestation Statements | June 04 2007 | ||||||
1 2 | Test Report | June 04 2007 | ||||||
1 2 | Cover Letter(s) | August 11 2005 / July 11 2005 | ||||||
1 2 | Test Report | August 11 2005 / July 11 2005 | ||||||
1 2 | Test Report | August 11 2005 / July 11 2005 | ||||||
1 2 | Test Report | August 11 2005 / July 11 2005 | ||||||
1 2 | External Photos | August 11 2005 / July 11 2005 | ||||||
1 2 | Internal Photos | August 11 2005 / July 11 2005 | ||||||
1 2 | ID Label/Location Info | August 11 2005 / July 11 2005 | ||||||
1 2 | Test Report | August 11 2005 / July 11 2005 |
1 2 | DRAFT RF SAFETY BOOKLET | Users Manual | 796.36 KiB | August 11 2005 / July 11 2005 |
95C98-C.book Page 1 Wednesday, October 27, 2004 11:59 AM Product Safety and RF Energy Exposure Booklet for Portable Two-Way Radios The information provided in this document supersedes the general safety information contained in user guides published prior to February 2002.
C a u t i o n BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION AND OPERATIONAL INSTRUCTIONS FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. ALSO READ THE OPERATIONAL INSTRUCTIONS FOR SAFE USAGE. FOR RADIOS THAT HAVE BEEN APPROVED AS INTRINSICALLY SAFE, READ THE INSTRUCTIONS AND INFORMATION ON INTRINSIC SAFETY ON PAGE 10 OF THIS BOOKLET. Motorola, Inc. 2004 8000 W. Sunrise Blvd., Ft. Lauderdale, FL 33322 68P81095C98 68P81095C98-C English 95C98-C.book Page 2 Wednesday, October 27, 2004 11:59 AM RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use NOTICE: This radio is intended for use in occupational/controlled conditions where users have full knowledge of their exposure and can exercise control over their exposure to meet the occupational limits in FCC and International standards. This radio device is NOT authorized for general population consumer use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. English 2 95C98-C.book Page 3 Wednesday, October 27, 2004 11:59 AM Please refer to the following websites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits:
http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Federal Communication Commission (FCC) Regulations The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for portable two-way radios before they can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a product label directing users to specific user awareness information. Your Motorola two-way radio has a RF Exposure Product Label. Also, your Motorola user manual, or separate safety booklet includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standards Your Motorola two-way radio is designed and tested to comply with a number of national and International standards and guidelines (listed below) for human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at operating duty factors of up to 50% talk-50%
listen and is authorized by the FCC for occupational use only. In terms of measuring RF energy for compliance with these exposure guidelines, your radio generates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. NOTE: The approved batteries, supplied with this radio, are rated for a 5-5-90 duty factor (5% talk-5% listen-90% standby) even though this radio complies with FCC occupational exposure limits and may operate at duty factors of up to 50% talk. 3 English 95C98-C.book Page 4 Wednesday, October 27, 2004 11:59 AM Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:
United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 Australian Communications Authority Radiocommunications (Electromagnetic Radiation Human Exposure) Standard, 2003 ANATEL ANNEX to Resolution No. 303 of July 2, 2002 "Regulation of limitation of exposure to electrical, magnetic and electromagnetic fields in the radio frequency range between 9 KHz and 300 GHz" and "Attachment to resolution #
303 from July 2, 2002"
RF Exposure Compliance and Control Guidelines and Operating Instructions To control your exposure and ensure compliance with the occupational/controlled environment exposure limits, always adhere to the following procedures. Guidelines:
Do not remove the RF Exposure Label from the device. User awareness instructions should accompany device when transferred to other users. Do not use this device if the operational requirements described herein are not met. English 4 95C98-C.book Page 5 Wednesday, October 27, 2004 11:59 AM Operating Instructions Transmit no more than the rated duty factor of 50% of the time. To transmit
(talk), push the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). Hold the radio in a vertical position in front of the face with the microphone (and other parts of the radio including the antenna) at least one inch (2.5 centimeters) away from the nose or lips. Antenna should be kept away from the eye. Keeping the radio at a proper distance is important since RF exposures decrease with increasing distance from the antenna. When worn on the body, always place the radio in a Motorola-approved clip, holder, holster, case, or body harness for this product. Using approved body-
worn accessories is important because the use of non-Motorola-approved accessories may result in exposure levels, which exceed the FCC occupational/controlled environment RF exposure limits. If you are not using a body-worn accessory and are not using the radio in the intended-use position in front of the face, ensure the antenna and the radio are kept at least one inch (2.5 centimeters) from the body when transmitting. Keeping the radio at a proper distance is important because RF exposures decrease with increasing distance from the antenna. Approved Accessories Use only Motorola-approved supplied or replacement antennas, batteries, and accessories. Use of Non-Motorola approved antennas, batteries, and accessories may exceed the FCC (IEEE) and ICNIRP RF exposure guidelines. For a list of Motorola-approved accessories, visit the following website, which lists approved accessories for your radio model:
http://www.motorola.com/cgiss/index.shtml. 5 English 95C98-C.book Page 6 Wednesday, October 27, 2004 11:59 AM Additional Information For additional information on exposure requirements or other training information, visit http://www.motorola.com/rfhealth. Electromagnetic Interference/Compatibility NOTE: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Aircraft When instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions. Medical Devices Pacemakers The Advanced Medical Technology Association (AdvaMed) recommends that a minimum separation of 6 inches (15 centimeters) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with those of the U.S. Food and Drug Administration. English 6 95C98-C.book Page 7 Wednesday, October 27, 2004 11:59 AM Persons with pacemakers should:
ALWAYS keep the radio more than 6 inches (15 centimeters) from their pacemaker when the radio is turned ON. Not carry the radio in the breast pocket. Use the ear opposite the pacemaker to minimize the potential for interference. Turn the radio OFF immediately if there is any reason to suspect that interference is taking place. Hearing Aids Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives. Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. Use of Communication Devices While Driving Always check the laws and regulations on the use of radios in the areas where you drive. Give full attention to driving and to the road. Use hands-free operation, if available. Pull off the road and park before making or answering a call, if driving conditions or regulations so require. 7 English 95C98-C.book Page 8 Wednesday, October 27, 2004 11:59 AM Operational Warnings
W A R N I N G For Vehicle With Air Bags:
Refer to vehicle manufacturer's manual prior to installation of electronic equipment to avoid interference with air bag wiring. Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. Potentially Explosive Atmospheres
(Explosive atmospheres refers to hazard classified locations that may contain hazardous gas, vapors, or dusts.) Turn off your radio prior to entering any area with a potentially explosive atmosphere unless it is a portable radio type especially qualified for use in such areas as Intrinsically Safe (for example, Factory Mutual, CSA, UL, or CENELEC). Do not remove, install, or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. English 8 95C98-C.book Page 9 Wednesday, October 27, 2004 11:59 AM
W A R N I N G The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often, but not always, posted. Blasting Caps and Blasting Areas To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: "Turn off two-way radio." Obey all signs and instructions. Operational Cautions
C a u t i o n Antennas Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. Batteries All batteries can cause property damage and/or bodily injury, such as burns, if a conductive material such as jewelry, keys, or beaded chains touches exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse, or other container with metal objects. 9 English 95C98-C.book Page 10 Wednesday, October 27, 2004 11:59 AM Intrinsically Safe Radio Information The Intrinsically safe approval unit refers to a product that has been approved as intrinsically safe by an approval agency (for example FM Approvals, CSA, UL, or Cenelec) and certifies that a particular product meets the Agency's applicable intrinsic safety standards for specific types of hazardous classified locations. A portable radio that has been approved for intrinsic safety will have Approval label attached to the radio to identify the unit as being Approved for specified hazardous atmospheres. This label specifies the hazardous Class/Division/Group along with the part number of the battery that must be used. The Intrinsically Safe Approval Label will be located on the portable radio unit. Operational Cautions for Intrinsic Safe Equipment
C a u t i o n Do not operate radio communications equipment in a hazardous atmosphere unless it is a type especially qualified (for example, FM, UL, CSA, or CENELEC approved). An explosion or fire may result. Do not operate a radio unit that has been approved as intrinsically safe product in a hazardous atmosphere if it has been physically damaged (for example, cracked housing). An explosion or fire may result. Do not replace or charge batteries in a hazardous atmosphere. Contact sparking may occur while installing or removing batteries and cause an explosion or fire. Warnings for Radios Approved as Intrinsically Safe Radios must ship from the Motorola manufacturing facility with the hazardous atmosphere capability and the intrinsic safety approval labelling (FM, UL, CSA, CENELEC). Radios will not be upgraded to this capability and labeled once they have been shipped to the field. English 10 95C98-C.book Page 11 Wednesday, October 27, 2004 11:59 AM A modification changes the units hardware from its original design configuration. Modifications can only be made by the original product manufacturer.
W A R N I N G
W A R N I N G Do not replace or change accessories in a hazardous atmosphere. Contact sparking may occur while installing or removing accessories and cause an explosion or fire. Turn the radio off before removing or installing a battery or accessory. Do not disassemble an intrinsically safe product in any way that exposes the internal circuits of the unit. Failure to use an intrinsically safe approved battery or Approved accessories specifically approved for the radio unit may result in the dangerously unsafe condition of an unapproved radio combination being used in a hazardous location. Unauthorized or incorrect modification of the intrinsically safe approved Product will negate the approval rating of the product. Incorrect repair or relabeling of any intrinsically safe Agency-
approved radio could adversely affect the Approval rating of the unit. Use of a radio that is not intrinsically safe in a hazardous atmosphere could result in serious injury or death. 11 English 95C98-C.book Page 12 Wednesday, October 27, 2004 11:59 AM Repair
W A R N I N G REPAIRS FOR MOTOROLA PRODUCTS WITH INTRINSICALLY SAFE APPROVAL ARE THE RESPONSIBILITY OF THE USER. Repairs to a Motorola FM approved radio product should only be done at a location that has been FM audited under the FM 3605 repairs and service standard. Contact Motorola for assistance regarding repairs and service of Motorola intrinsically safe equipment. A repair constitutes something done internally to the unit that would bring it back to its original condition. Items not considered as repairs are those in which an action is performed on a unit which does not require the outer casing of the unit to be opened in a manner that exposes the internal electrical circuits of the unit. Do Not Substitute Options or Accessories The Motorola communications equipment certified as intrinsically safe by the approving agency, (FM, UL, CSA, CENELEC) is tested as a complete system which consists of the listed agency Approved portable, Approved battery, and Approved accessories or options, or both. This Approved portable and battery combination must be strictly observed. There must be no substitution of items, even if the substitute has been previously Approved with a different Motorola communications equipment unit. Approved configurations are listed by the Approving Agency (FM, UL, CSA, CENELEC). The Intrinsically Safe Approval Label affixed to radio refers to the intrinsically safe classification of that radio product, and the approved batteries that can be used with that system. English 12 95C98-C.book Page 13 Wednesday, October 27, 2004 11:59 AM The manual PN referenced on the Intrinsically Safe Approval Label identifies the approved Accessories and or options that can be used with that portable radio unit. Using a non Motorola intrinsically safe battery and or accessory with the Motorola approved radio unit will void the intrinsically safe approval of that radio unit. 13 English 95C98-C.book Page 14 Wednesday, October 27, 2004 11:59 AM Notes English 14
1 2 | USERS MANUAL | Users Manual | 2.86 MiB | August 11 2005 / July 11 2005 |
ATS2500.book Page 1 Monday, December 18, 2000 7:39 PM C O N T E N T S CONTENTS Radio Overview . 4 Operation and Control Functions . 5 Radio Controls . 5 Programmable Buttons . 7 Keypad Keys (for Model II radios only) . 8 Menu Keys (for Model II radios only) . 9 Selecting a Feature. 9 Menu Display . 10 LCD Screen and Icons . 10 Alert Tone Indications . 11 Getting Started . 13 Battery Information. 13 Battery Care and Tips . 13 Recycling or Disposal of Batteries . 14 Charging the Battery . 14 Accessory Information . 15 Attaching the Battery. 15 Removing the Battery . 15 Attaching the Antenna. 16 Removing the Antenna . 16 Attaching the Belt Clip. 17 Removing the Belt Clip . 17 Attaching the Dust Cover . 18 Radio Operation . 19 Turning The Radio On or Off . 19 Adjusting the Radios Volume. 19 Radio Self Test . 19 Basic Radio Calls . 20 Selecting a Zone and Mode. 20 Selecting a Zone
(for Model II radios only). 20 Selecting a Mode . 20 Receiving a Call. 21 Making a Call. 21 Conventional Modes. 21 Trunked Modes. 21 Low-Battery Alert . 22 Coded Squelch Operation . 22 Variable RF Power Level
(Selected Models Only) . 22 Failsoft Operation
(Trunked Systems Only) . 22 Muting the Keypad Tones
(for keypad Radios only) . 23 Trunked Features . 24 Viewing Your Radios ID Number . 24 Enhanced Private Call Operation . 24 1 ATS2500.book Page 2 Monday, December 18, 2000 7:39 PM S T N E T N O C Answering a Private Call. 24 Making a Private Call . 25 Leaving a Call Alert Page . 28 Call Alert Operation . 28 Answering a Call Alert Page with a Group Call . 28 Making a Call Alert . 29 Automatic Multiple Site Selection (AMSS) 31 Viewing the Current Site . 31 Forcing a Site Change . 32 Locking and Unlocking a Site . 32 Conventional Features . 33 Repeat/Direct . 33 Smart PTT . 33 Scan. 35 Scan Operation . 35 Turning Scan On or OFF with the Keypad
(for Keypad radios only) . 35 Deleting Nuisance Modes . 36 Viewing a Scan List
(for keypad radios only) . 36 Programming a Scan List
(for keypad radios only) . 37 Scan Modes . 38 2 Programming the Radio . 39 Programming the Telephone List Numbers . 39 Programming the Call List . 40 Telephone Operation. 42 Answering a Telephone Call. 42 Making a Telephone Call
(for Model II radios only). 42 Special Features . 46 Emergency Operation . 46 Sending an Emergency Alarm . 46 Sending a Silent Emergency Alarm . 47 Canceling an Emergency Alarm . 47 Sending an Emergency Call . 47 Ending an Emergency Call . 48 Emergency with Voice to Follow. 48 Dynamic Regrouping . 48 Mode Selection. 48 Select Enable and Disable . 49 SmartZone Operation . 50 Benefits of SmartZoneTM . 50 Site Switching in SmartZone . 51 Viewing the Current Site. 52 ATS2500.book Page 3 Monday, December 18, 2000 7:39 PM PTT-ID . 60 Radio Check . 60 Emergency Operation . 60 C O N T E N T S Forcing a Site Change . 52 Locking and Unlocking a Site . 52 Preferred Site Selection . 52 Busy Override . 53 Site Trunking. 54 Stat-Alert Features . 55 Viewing Your Radios ID Number. 55 Stat-Alert Voice Selective Call Operation. 55 Receiving a Voice Selective Call . 56 Making a Voice Selective Call. 56 Stat-Alert Call Alert Operation . 58 Receiving a Call Alert Page . 58 Making a Call Alert . 59 3 ATS2500.book Page 4 Monday, December 18, 2000 7:39 PM I W E V R E V O O D A R I RADIO OVERVIEW This user guide covers the operation of the ATS 2500 Portable Radio. Please read the Safety Information on pages 61 to 64 using this radio. before 1. Mode Selector Knob 2. On-Off / Volume Knob 7. Top Button 8. LED Indicator 10. Antenna 3. Side Button 1/
Select Key 4. Push to Talk (PTT) Button 5. Side Button 2 6. Side Button 3 4 11. Dust Cover covering Accessory Connector 9. Microphone Model I ATS2500.book Page 5 Monday, December 18, 2000 7:39 PM 1. Mode Selector Knob 2. On-Off / Volume Knob 7. Top Button 3. Side Button 1/
Select Key 4. Push to Talk (PTT) Button 5. Side Button 2 6. Side Button 3 8. LED Indicator 9. Microphone 12. LCD Screen 13. Menu Keys 14. Keypad Model II 10. Antenna 11. Dust Cover covering Accessory Connector OPERATION AND CONTROL FUNCTIONS Radio Controls Refer to the illustrations above and on the previous page. 1. Mode Selector Knob Used to select the required operation mode. 2. On-Off / Volume Knob Used to turn the radio on or off, and to adjust the radios volume. 5 I R A D O O V E R V E W I ATS2500.book Page 6 Monday, December 18, 2000 7:39 PM 3. Side Button 1/Select Key (programmable) Recommended for the Monitor Button. Also functions as the select key when programming your radios lists. 4. Push to Talk (PTT) Button Press and hold down this button to talk, release it to listen. 5. Side Button 2 (programmable) 6. Side Button 3 (programmable) 7. 8. Top Button (programmable) Recommended as Emergency button. LED Indicator The indicator LED on top of the radio indicates radio operating conditions. With PTT switch pressed (radio transmitting) Continuous red LED Normal transmission. LED unlit Radio is not transmitting. Blinking red light Low battery (conventional mode only; programmable from the CPS) With PTT switch released (radio receiving) Blinking red light Mode busy (conventional mode only). Receipt of a telephone call, Pri-
vate Conversation call, or Call Alert page. Blinking green light 9. Microphone Speak clearly into the microphone when send-
ing a message. 10. Antenna 11. Accessory Connector Connects headsets, remote speaker/micro-
phones and other accessories. Replace attached dust cover when not in use. Additionally for keypad radios (Model II), there are 12. LCD Screen 13. Menu Keys 14. Keypad 6 I W E V R E V O O D A R I ATS2500.book Page 7 Monday, December 18, 2000 7:39 PM Programmable Buttons Several of your radio buttons can be programmed (by using the Customer Programming Software CPS) to activate the radio features. Programmable buttons are Top button Three side buttons Check with your dealer or Motorola representative for a complete list of the functions your radios programmable buttons support. The table below shows the functions available by
- pressing and holding the
- quickly pressing and releasing the short press programmable buttons, or long press programmable buttons for a period of time before releasing, or hold down programmable buttons while checking status or making adjustments.
- pressing and holding down the Button Short Press Long Press Hold Down Monitor/Permanent Monitor Volume Set Scan Nuisance Delete Search Light Emergency Call Page
Toggles between the start/stop of the Scan operation. Temporarily deletes an unwanted non-priority active scan member. Makes a system search. Turns on/off your radios backlight. Enters Emergency mode. Enters or exits a Private call. Enters or exits a Call Alert. Continually monitors the selected channel.
Leaves Emergency mode. Monitors the selected channel for any activity. Sounds a tone for adjusting the radios volume level.
7 I R A D O O V E R V E W I ATS2500.book Page 8 Monday, December 18, 2000 7:39 PM Button Short Press Long Press Hold Down Call Response Phone Respond to or exit from a Private Call or Call Alert. Enters or leaves Phone mode.
I W E V R E V O O D A R I Keypad Keys (for Model II radios only) 1 2 3 4 5 6 7 8 9
* 0 #
These keys are used when dialing a phone number, making a radio call or entering information for programming the radios lists. The following table shows the character cycle for each key, when entering information for programming the radios lists. Number of Times the Key is Pressed Key 0 1 1 0 1 2 3 4 5 6 Blank space 8
7 9
2 3 4 5 6 S 8 Z
2 3 4 5 6 7 8 A D G J M P T 9 W
B E H K N Q U X
C F I L O R V Y
Note:
The sequence in the table above is valid when entering information on a blank display. However, when editing existing information, the above sequence may differ. For instance, if the ATS2500.book Page 9 Monday, December 18, 2000 7:39 PM 7 last character entered is a to enter the next character, would start the char-
acter cycle at
, pressing
and NOT at R S P
. When editing existing information, pressing 1 the would blank space ALWAYS
and start the character cycle at NOT 1 at
. Menu Keys (for Model II radios only) Softkey 1 Softkey 2 Softkey 3 l ; l
Left Home Right Selecting a Feature A unique feature of your radio is its use of the display to give you quick access to many of the radios features without having to have a dedicated key for each feature. The names of the features (CALL, MUTE, etc.) are shown on the display, three at a time. Selection of features is controlled by the three keys directly below the feature names: the left key controls the left feature, the middle key controls the middle feature, and the right key controls the right feature. Softkeys (l;l) When already in Menu Mode, these keys are used to make Menu selections. Left and Right Arrow Keys (,/) The left and right arrow keys are used to scroll the display forward or backward through the radios features and lists. There is no end point to the list, so if you continue to scroll in one direction, the display will
wrap around back to the beginning of the list. If you hold either key down, the display will scroll at a faster rate until the key is released. The left arrow key is also used for editing when you are entering information manually from the keypad. Pressing the left arrow key, when editing numeric information (such as telephone numbers), will backspace, and erase the display, one character at a time. If you have erased all the digits, an additional press of the left arrow key will return the display to the pre-programmed list. Pressing the left arrow key, when editing alphabetic information (such as members names), will move the cursor one step to the left. HOME Key (.) The HOME key will always return you to the home
(default) display. In most cases, this is the current mode. In addition, if you are using a feature that 9 I R A D O O V E R V E W I ATS2500.book Page 10 Monday, December 18, 2000 7:39 PM requires it, pressing the HOME key will also cause information to be saved in memory before going to the home display. Some radio features will automatically go to the home display when they are completed, without having to press the HOME key, thus reducing the number of key presses required. Menu Display The menu items can be displayed in normal video or in reversed video (programmable through the CPS). All the menu items in the examples in this manual are shown in reversed video. The order in which the menu items are displayed is programmable. Thus, the order of the menu items on your radio may differ from those shown here in this manual. In such a situation, press the relevant softkey to make your menu selections. All descriptions of functions and displays after the selection are valid. LCD Screen and Icons Displays mode selected, channel, menu, and radio status information. The top two screen rows show 10 radio status indicator symbols, explained in the following table. Symbol Name and Description A XPAND Indicator Indicates that your radio has the companding feature activated. B C F G H Power Level Indicator R lights up when your radio is congured to transmit in Low Power. S lights up when your radio is congured to transmit in High Power. Carrier Squelch Indicator Indicates when the active conventional mode is being monitored in the carrier squelch mode;
ON = BEING MONITORED/
OFF = NOT BEING MONITORED. Call Received Flashes when a call or page is received. Scan Indicator Indicates when the radio is scanning;
ON = SCANNING/OFF =NOT SCANNING. Priority Scan The presence of a dot along with the scan annunciator indicates the receiving of a priority mode;
BLINKING DOT = PRIORITY 1 SOLID DOT = PRIORITY 2. I W E V R E V O O D A R I ATS2500.book Page 11 Monday, December 18, 2000 7:39 PM Symbol Name and Description J K M P Direct Indicates whether you are talking directly to another radio (talkaround), or through a repeater;
ON = DIRECT OFF = REPEATER. Programming/Viewing Mode Indicates when the radio is in the programming or viewing mode;
ON = IN VIEWING MODE BLINKING = IN PROGRAMMING MODE. Signal Quality Indicator Shows the radio signal quality. Five bars indicates the best signal (Smart Zone Only). Battery Level Indicator Shows the remaining charge in your battery, based on how many bars are displayed. Flashing, indicates at battery. Alert Tone Indications Your radio generates a number of audible tones to indicate radio operating conditions:
Low Battery A low-battery condition is indi-
cated by a high-pitched, cricket-like chirp-chirp when the PTT switch is released following a transmission. Successful Power-Up A short, medium-pitched tone when the radio is rst turned on indicates that the radio has passed its power-up self test and is ready for use. Unsuccessful Power-Up A short, low-pitched tone when the radio is rst turned on indicates that the radio has failed its power-up self test and is not ready for use. Contact your service representative for service. Transmit on Receive-Only Mode If you press the PTT switch while tuned to a receive-only mode, you will hear a continuous, low-pitched alert tone, indicating that no transmission is pos-
sible on this mode. This tone will continue until the PTT switch is released. Transmit Inhibit on Busy Mode If you press the PTT switch while the mode is busy, you will hear a continuous, low-pitched alert tone, indicating that no transmission is possible on this mode. This tone will continue until the PTT switch is released. Transmit Inhibit on Flat Battery If you press the PTT while the battery is at, you will hear a con-
tinuous, low pitched alert tone, indicating that transmission is impossible. Invalid Mode A continuous, low-pitched tone is heard when an invalid or unprogrammed opera-
tion is attempted on the radio. 11 I R A D O O V E R V E W I ATS2500.book Page 12 Monday, December 18, 2000 7:39 PM Valid (Good) Key Press A short, medium-
switch is released. pitched tone when a keypad key is pressed indi-
cates that the key press was accepted. Invalid (Bad) Key Press A short, low-pitched tone when a keypad key is pressed indicates that the key press was rejected. Emergency Alarm Entry A short, medium-
pitched tone when the emergency button is pressed indicates that the radio has entered the emergency mode. Emergency Alarm/Call Exit A continuous, medium-pitched tone when the radio is in the emergency mode indicates that the radio has exited the emergency mode. Failsoft (Trunked Systems Only) A faint beep-
ing tone every ten seconds indicates that the radio is operating in the failsoft mode. Time-Out Timer Warning Your radios time-out timer limits the length of your transmission time. When you are pressing the PTT switch (transmit-
ting), a short, low-pitched warning tone will sound four seconds before the allotted time will expire. Time-Out Timer Timed-Out If you hold down the PTT switch longer than the time-out timers allotted time, a continuous, low-pitched tone will sound, indicating that your transmission has been cut off. This tone will continue until the PTT Phone Busy A bah-bah-bah-bah tone when telephone interconnect is accessed indicates that all available modes are busy and the radio is in queue for the next available phone line. Call Alert (Page) Received A group of four medium-pitched tones every ve seconds indi-
cates that your radio has received a Call Alert page. Call Alert (Page) Sent A single medium-
pitched tone (central acknowledge), followed by a group of four medium-pitched tones indicates that a Call Alert page sent by your radio has been received by the target radio. Private Conversation Call Received A group of two medium-pitched tones indicates that your radio has received a Private Conversation call. This sequence is repeated every ve seconds for approximately 20 seconds for enhanced Pri-
vate Conversation. Trunked System Busy (Trunked Systems Only) A bah-bah-bah-bah tone when a trunked sys-
tem is accessed indicates that all available chan-
nels are busy and the radio is in queue for the next available channel. Call Back (Trunked Systems Only) A group of three medium-pitched tones (di-di-dit) indicates that a talkgroup is now available for your previ-
ously requested transmission. 12 I W E V R E V O O D A R I ATS2500.book Page 13 Monday, December 18, 2000 7:39 PM GETTING STARTED BATTERY INFORMATION Battery Care and Tips This product is powered by a nickel-cadmium (NiCd), nickel-metal-hydride (NiMH), or lithium-ion rechargeable battery. The following battery tips will help you obtain the highest performance and longest cycle life from your Motorola rechargeable battery. Charge your new battery overnight (14-16 hours) before using it to obtain maximum battery capacity and performance. Charging in non-Motorola equipment may lead to battery damage and void the battery warranty. When charging a battery that is attached to the radio, turn the radio off to ensure a full charge. The battery should be at about 25C (room temperature) whenever possible. Charging a cold battery (below 10C) may result in leakage of electrolyte and ultimately, in failure of the battery. Charging a hot battery (above 35C) results in reduced discharge capacity, affecting the performance of the radio. Motorola rapid-rate battery chargers contain a temperature-sensing circuit to ensure that the battery is charged within these temperature limits. New batteries can be stored up to two years without signicant cycle loss. Store new/unused batteries in a cool dry area. Batteries which have been in storage should be charged overnight. Do not return fully charged batteries to the charger for an extra boost. This action will signicantly reduce cycle life. Do not leave your radio and battery in the charger when not charging. Continuous charging will shorten battery life. (Do not use your charger as a radio stand.) For optimum battery life and operation use only Motorola brand chargers. They were designed to operate as an integrated energy system. 13 I G E T T N G S T A R T E D ATS2500.book Page 14 Monday, December 18, 2000 7:39 PM Recycling or Disposal of Batteries NiCd At the end of its useful life, the NiCd battery can be recycled. However, recycling facilities may not be available in all areas. Motorola endorses and encourages the recycling of all re-chargeable batteries. Contact your local Motorola dealer for further information. Charging the Battery If a battery is new, or its charge level is very low, indicated by battery level indicator showing one or no segments, you will need to charge the battery before you can use it in your radio. Note:Batteries are shipped uncharged from the factory. New batteries could prematurely indicate full charge, charge a new battery for 14-16 hours before initial use. 14 Charger LED Status Red Green Battery is charging Battery is fully charged Flashing Red *
Battery is unchargeable Flashing Yellow Charger is getting ready to charge Flashing Green
* Battery is damaged. Please contact your dealer. Battery is 90% charged 1. Place the radio with the battery attached, or the 2. battery alone, in the charger. The chargers LED indicates the charging progress. Battery chargers will charge only the Motorola authorized batteries listed below; other batteries will not charge. Part No. HNN9008 HNN9009 HNN9010 HNN9011 HNN9012 HNN9013 Description High-Capacity NiMH Ultra-High-Capacity NiMH Ultra-High-Capacity FM NiMH High-Capacity FM NiCd High-Capacity NiCd Lithium-Ion FM - Factory Mutual D E T R A T S G N T T E G I ATS2500.book Page 15 Monday, December 18, 2000 7:39 PM ACCESSORY INFORMATION Attaching the Battery Removing the Battery Battery Latches 2 3 2 1 Slots 1. Fit the extensions at the bottom of the battery into the slots at the bottom of the radios body. 2. Press the top part of the battery towards the radio until you hear a click. 1. Turn off the radio, if it is turned on. 2. Slide the battery latches, on both sides of the battery, downwards. 3. Pull the top part of the battery away from the radios body, and remove the battery. 15 I G E T T N G S T A R T E D ATS2500.book Page 16 Monday, December 18, 2000 7:39 PM Attaching the Antenna Removing the Antenna 1. Align the threaded end of the antenna with the radios antenna connector. 2. Turn the antenna clockwise to fasten it. 16 Turn the antenna counterclockwise until you can remove it. D E T R A T S G N T T E G I ATS2500.book Page 17 Monday, December 18, 2000 7:39 PM Attaching the Belt Clip Removing the Belt Clip Belt Clip Tab 1 2 1. Align the grooves of the belt clip with those 1. Use a key to press the belt clip tab away of the battery. from the battery. 2. Press the belt clip downwards until a click is 2. Slide the belt clip upwards to remove it. heard. 17 I G E T T N G S T A R T E D ATS2500.book Page 18 Monday, December 18, 2000 7:39 PM Attaching the Dust Cover Dust Cover Loop Dust Cover Tab Slot for Dust Cover Tab Thumbscrew 1. Place the dust cover loop over the attached antenna. 4. Tighten the thumbscrew to hold the cover in place. DO NOT overtighten the thumbscrew. 2. Slide the loop all the way down to the base of the antenna. 3. Insert the dust cover tab into the slot above the connector. 18 D E T R A T S G N T T E G I ATS2500.book Page 19 Monday, December 18, 2000 7:39 PM RADIO OPERATION Turning The Radio On or Off ON OFF To turn the radio on, turn the On-Off/Volume Con-
trol knob clockwise. To turn the radio off, turn the On-Off/Volume Con-
trol knob counterclockwise until you hear a click. Adjusting the Radios Volume Turn the On-Off/Volume Control knob to adjust the volume level. Listen until you hear a transmission, then adjust the volume control for a comfortable listening level. Or, if a button is programmed for volume set, press this button and adjust the volume to a com-
fortable listening level. Radio Self Test Turn the radio on by rotating the volume control clockwise. The radio goes through a power-up self check and, if it passes the check, the display momentarily shows SELF TEST. A good-power-up, high-pitched tone sounds to indicate that the radio has passed the self check. If the radio fails the self check, the display shows
ERROR XX/XX (where XX/XX is an alphanumeric error code), accompanied by a bad-power-up, low-
pitched tone. Turn the radio off, check the battery, and turn the radio back on. If the radio still does not pass the self check, a problem exists in the radio. Contact your nearest Motorola Service Shop. Note: The power-up self check veries that the radios microprocessor-based systems are work-
ing, but it does not check all of the rf compo-
nents, nor does it check the operation of all customer-specic recom-
mends that the functionality of the radio be peri-
odically checked by an authorized Motorola service shop. features. Motorola 19 I G E T T N G S T A R T E D I S L L A C O D A R C S A B I ATS2500.book Page 20 Monday, December 18, 2000 7:39 PM BASIC RADIO CALLS This section outlines the basic functions of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below PLANT POLICE is used to indicate the radios home display. SELECTING A ZONE AND MODE A mode is a channel or talkgroup and all the features that are programmed to it. A zone is a grouping of modes that is selected using the menu keys. Before you use your radio to receive or send messages, you should rst select the desired zone and mode. Selecting a Zone
(for Model II radios only) 1. Press / until ZONE is displayed. 2. Press l (the soft-
key below ZONE). The current zone name blinks on the display. 20 3. Press / until the desired zone name is displayed.
or Enter the number of the desired zone. 4. Press .. 5. The displayed zone is the new selected zone. Selecting a Mode For example CITY POLICE CITY POLICE 1. Turn the mode selector knob to the desired mode. 2. The display shows the selected modes name. For example PLANT MODE 1 ZONE MUTE CALL 3. For example PLANT POLICE If the selected mode is unprogrammed, an invalid-mode tone is heard until a valid programmed mode is selected. UNPROGRAMMED I B A S C R A D O C A L L S I ATS2500.book Page 21 Monday, December 18, 2000 7:39 PM RECEIVING A CALL 1. Turn the radio on and select the desired zone and mode (see Selecting a Zone and Mode). 2. Your radio is now set to receive calls on the selected mode. If the mode-busy feature is enabled, a blink-
ing red LED on receive (PTT released) indicates that the mode is currently busy. If a mode is programmed for receive only, any attempt to transmit on that mode will cause an invalid-mode tone to sound until the PTT switch is released. MAKING A CALL Conventional Modes 1. Turn the radio on and select the desired con-
ventional zone and mode (see Selecting a Zone and Mode). 2. Press and hold the PTT switch on the side of the radio and speak slowly and clearly into the microphone area. The red LED lights continuously when the radio is transmitting. 3. When you have nished talking, release the PTT to listen. Note: Do not interrupt another user. If the present mode is programmed to receive PL, ensure that the mode is not in use by pressing the monitor button to listen for activity. Trunked Modes 1. Turn the radio on and select the desired trunked zone and mode (see Selecting a Zone and Mode). 2. Press and hold the PTT switch on the side of the radio and speak slowly and clearly into the microphone area. The red LED lights when the radio is transmitting. When you have nished talking, release the PTT to lis-
ten. Note: If you hear a busy signal (a low-frequency
bah-bah-bah-bah), release the PTT switch and wait for a call-back tone (sounds like di-di-dit). When you hear the call-back tone you will have three seconds to press the PTT switch. This allows you to make another call without getting a busy signal. 21 I S L L A C O D A R C S A B I ATS2500.book Page 22 Monday, December 18, 2000 7:39 PM If a continuous talk-prohibit tone is heard when the PTT switch is pressed, transmission is not possible. The radio may be out of range. Low-Battery Alert Your radio emits an alert tone when a low-battery condition is detected. Coded Squelch Operation Tone Private-Line (PL), Digital Private-Line (DPL), and carrier squelch operation are all available in your radio, on a per-mode basis. When in carrier squelch operation, all trafc on the mode is heard. When in PL or DPL operation, your radio responds to only those messages intended for you. When this feature is mode-slaved, PL, DPL, or carrier squelch is programmed to each mode. Whenever the radio is operating in carrier squelch, the display will show C. Variable RF Power Level
(Selected Models Only) Radios can have more than one power level. High power can be programmed on modes where high power is permitted, and low power can be programmed on all other modes. The high-/low-power feature can be selected via the menu keys. 22 FAILSOFT OPERATION
(TRUNKED SYSTEMS ONLY) The failsoft system ensures continual radio communications capability during a trunked system failure. Your radio will automatically go into failsoft operation, if the central trunking controller fails for any reason. While in failsoft operation, your radio will transmit and receive on a predetermined frequency on a conventional mode. When the trunked system returns to normal operation, the radio will automatically leave the failsoft operation and return to trunked operation. During failsoft operation, 1. You will hear a faint Alternates between
beeping sound every ten seconds. FAILSOFT and PLANT POLICE 2. Your radio becomes unsquelched. I B A S C R A D O C A L L S I ATS2500.book Page 23 Monday, December 18, 2000 7:39 PM MUTING THE KEYPAD TONES
(FOR KEYPAD RADIOS ONLY) The radios keypad tones, normally heard each time a keypad key is pressed, can be turned off (muted) or on
(unmuted) at your discretion. To use the keypad mute feature 1. Press / until MUTE is displayed. 2. Press ; (the soft-
key below MUTE). ZONE MUTE CALL You will see the cur-
rent mute state momentarily. TONES ON or TONES OFF Then ON OFF 3. Press the softkey below the desired mute state (on or off). The radio returns to the home display. PLANT POLICE Note: Pressing . or the PTT switch will exit this menu without changing the mute selection. 23 ATS2500.book Page 24 Monday, December 18, 2000 7:39 PM TRUNKED FEATURES This section outlines the trunked features of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below PLANT POLICE is used to indicate the radios home display. VIEWING YOUR RADIOS ID NUMBER To view your radios ID number 1. Press / until CALL is displayed. ZONE MUTE CALL 2. Press l (the softkey below CALL). S E R U T A E F D E K N U R T 3. The display shows the last ID number transmit-
ted or received. 4. Press ,. 5. The display shows your radios ID number. 6. Press . to return the radio to the home dis-
play. 24 Note: If your radio has been so programmed, you can press the call button for quick access to viewing your radios ID number. This takes you directly to step 3. ENHANCED PRIVATE CALL OPERATION The Enhanced Private Conversation feature not only allows you to have a conversation that is heard only by the two parties involved, but also enables you to determine whether the radio that you are calling is in service. The radio being called can also view the calling radios ID number before answering. You can then choose whether or not to leave your radios ID number (via a Call Alert page) with the radio you are calling so that you may be called back. Enhanced Private Conversation operation is similar to telephone operation. ID: 722588 Answering a Private Call 1. Upon receiving a Pri-
vate Conversation call, two alert tones sounds
(repeating every ve seconds for 20 sec-
onds). Alternates between CALL RECEIVED and PLANT POLICE MY ID:741317 PLANT POLICE ATS2500.book Page 25 Monday, December 18, 2000 7:39 PM 2. The green LED and call received status annunciator, F, will blink indicating that a call is being received. You have 20 seconds to answer the call before the radio automatically returns to the home display. 3. Press the call response button or the call but-
ton. 4. The display shows the incoming callers ID number, and the call received annunciator will turn off. ID: 722588 5. After viewing the callers ID number, you can decide to either talk privately (go to next step), or not answer the call by pressing the call response or call button to return to the home display. 6. If you decide to answer the call, press the PTT switch. 7. The callers ID number remains displayed for the duration of the call. ID: 722588 8. When nished with conversation, press . or the call response button to hang up. 9. The radio will return to the home display. PLANT POLICE Note: If you press the PTT switch before you press the call response button, the response will be transmitted to everyone in the talkgroup (a dis-
patch mode operation). After answering a Private Call, the callers ID number is stored in your radio as the last ID number received. If your radio is congured for Private Call II, upon receiving a Private Conversation call, two alert tones sounds, followed by the received voice. Making a Private Call There are four phases in making a private call, namely initiating a private call, entering the desired radio ID number, sending the radio ID number, and having the conversation and hanging-up. Initiating a Private Call 1. Press / until CALL is displayed. ZONE MUTE CALL 2. Press l (the softkey below CALL). T R U N K E D F E A T U R E S 25 ATS2500.book Page 26 Monday, December 18, 2000 7:39 PM S E R U T A E F D E K N U R T 3. The display shows the last ID number transmit-
ted or received. ID: 722588 Entering the Desired Radio ID Number If the last ID number called is the desired number, go directly to step 5. To enter a new number 4a. Enter the new six-digit ID number using the keypad. 4b. On the display, the old ID number disappears and the new digits appear as they are being entered. 4c. The cursor ashes indicating the location of the next number to be entered. Note: Exactly six digits must be entered for the radio ID number. If fewer than six digits were entered, you will hear a bad-keypress tone and the display will show INVALID ENTRY when attempting to send the radio ID number. A bad-
keypress tone will also be heard if you try to enter a seventh digit. Once you have started entering numbers, the , key functions as a backspace key. Pressing it causes the last digit entered to be 26 erased, and the cursor moves to the left. When the last digit is erased, an additional press of this key causes the last ID number transmitted or received to be displayed; pressing / shows the rst member of the list. To enter a number from the call list 4a. Press either , or /. 4b. / takes you forward to the rst or next member of the list; , takes you backwards to the last or previous member of the list. 4c. When at a member of Alternates between the list, the display alter-
nates between showing the members name and ID number. CK TANG and ID: 784116 To enter a number from a location in the call list 4a. Press either , or / to enter the call list. 4b. Enter the rst digit of the location number. If there are fewer than 10 members in the list, go directly to step 4e. ATS2500.book Page 27 Monday, December 18, 2000 7:39 PM 4c. If there are 10 or more members in the list, the display shows ID LOC#X_ (where X is the rst digit). The cursor blinks to show the location of the second digit. 4d. Enter the second digit of the location number. 4e. The radio goes to that position in the list. The display alternates between showing the members name and ID number. Alternates between CK TANG and ID: 784116 Note: The last member of the list is also the last ID transmitted or received at position 00 on the list. If you enter a location number that does not exist (for example, 15), the display will show
INVALID ENTRY, and the radio will sound an invalid-keypress tone and return back to step 4b of this procedure. Sending the Radio ID Number 5. Press the PTT switch to transmit the ID num-
ber. 6. If the radio you are calling is on the air, you will hear a telephone-type ringing for 20 seconds, or until the called radio answers the call. 7. If the party you are call-
ing does not answer the call within twenty sec-
onds, the telephone ring-
ing stops and an alert tone sounds. NO ANSWER At this point you can either send a Call Alert page, or go to step 10 to hang up. 8. If the party you are calling answers the call, you will hear his/her voice. Note: If the radio you are calling is not in service, you will not hear the ringing and the display will show NO ACK. Go to step 10 to hang up. If your radio is congured for Private Call II, you will not hear the telephone type ringing. Instead you are able to proceed to talk to the Called party. Having the Conversation and Hanging-up 9. Press the PTT switch to have a Private Con-
versation with the called person. 10. When nished with your conversation, or if the radio you called does not answer or is not in service, press . to hang up. T R U N K E D F E A T U R E S 27 ATS2500.book Page 28 Monday, December 18, 2000 7:39 PM 11. The radio will return to the home display. PLANT POLICE Note: Once engaged in a private conversation, if the radio is left idle for more than one minute, a momentary warning alert sounds every six sec-
onds to remind you that dispatch calls are not being heard. After two minutes, a permanent invalid mode tone sounds. Leaving a Call Alert Page 1. If the party you want to have a Private Call does not answer the call within twenty sec-
onds, you can choose to leave a Call Alert page. This leaves your radios ID number with the called radio so you can be called back later. 2. Press the PTT switch to send the Call Alert page. You will hear ve beeps, indicating that the system has received your ID number and the radio you are calling is on the air. 3. Press .. 4. The radio will return to the home display. PLANT POLICE CALL ALERT OPERATION Answering a Call Alert Page with a Group Call 1. Upon receiving a Call Alert page, four alert tones sounds (repeats every 5 seconds). 2. The green LED lights and the Call Received annunciator, F, blinks indicating a call is received. 3. Press the PTT switch to answer the page. 4. The display shows the current talkgroup. The audible alert, LED and call received annunciator turns off. FIRE DEPT 5. The ID number of the radio that paged you is stored as the last ID number received. 6. Have your conversation in the normal manner;
all members of your talkgroup will hear your response. Press the PTT switch to talk;
release the switch to listen. Note: When you received a Call Alert page, you can enter Private Call mode and call the paging radio using the latest ID received. S E R U T A E F D E K N U R T 28 ATS2500.book Page 29 Monday, December 18, 2000 7:39 PM Making a Call Alert To enter a new number There are three phases in making a call alert, namely 4a. Enter the new six-digit ID number using the initiating a call alert, entering the radio ID number that you wish to page, and sending the call alert. Initiating a Call Alert 1. Press / until PAGE is displayed. PAGE PHON VIEW 2. Press l (the softkey below PAGE). 3. The display shows the last ID number transmit-
ted or received. ID: 722588 Note: The same list is shared by both Call Alert and Private Conversation features. If your radio has been so programmed, you can press the page button for quick access to the Call Alert feature. This will take you directly to step 3. Entering the Radio ID Number that you wish to Page If the last ID number called or received is the desired number, go directly to step 5. keypad. 4b. On the display, the old ID number disappears and the new digits appear as they are being entered. 4c. The cursor ashes indicating the location of the next number to be entered. Note: Exactly six digits must be entered for the radio ID number. If fewer than six digits were entered, you will hear a bad-keypress tone when attempting to send the radio ID number. A bad-
keypress tone will also be heard if you try to enter a seventh digit. Once you have started entering numbers, the , key functions as a backspace key. Pressing it causes the last digit entered to be erased, and the cursor moves to the left. When the last digit is erased, an additional press of this key causes the last ID number transmitted or received to be displayed; pressing / shows the rst member of the list. To enter a number from the call list 4a. Press either , or /. T R U N K E D F E A T U R E S 29 ATS2500.book Page 30 Monday, December 18, 2000 7:39 PM 4b. / takes you forward to the rst or next member of the list; , takes you backwards to the last or previous member of the list. 4c. When at a member of Alternates between the list, the display alter-
nates between showing the members name and ID number. CK TANG and ID: 784116 To enter a number from a location in the call list 4a. Press either , or / to enter the call list. 4b. Enter the rst digit of the location number. If there are fewer than 10 members in the list, go directly to step 4e. 4c. If there are 10 or more members in the list, the display shows ID LOC#X_ (where X is the rst digit). The cursor blinks to show the location of the second digit. 4d. Enter the second digit of the location number. S E R U T A E F D E K N U R T 30 4e. The radio goes to that position in the list. The display alternates between showing the members name and ID number. Alternates between CK TANG and ID: 784116 Note: The last member of the list is also the last ID transmitted or received at position 00 on the list. If you enter a location number that does not exist (for example, 15), the display will show
INVALID ENTRY, and the radio will sound an invalid-keypress tone and return back to step 4b of this procedure. Sending the Call Alert 5. Press the PTT switch to transmit the ID num-
ber. ATS2500.book Page 31 Monday, December 18, 2000 7:39 PM If the page is unsuccessful 6a. If you hear one beep, the ID number has been received by the system, but the radio you are paging is not on the air; your radio remains in the Call Alert mode. If after six seconds the called radio fails to acknowledge the alert, a low-pitched alert tone sounds and the display changes to NO ACKNOWLEDGE. 6b. Press the PTT switch to send the ID number again, or press . to hang up and return to the home display. If the page is successful 6a. If you hear ve beeps, the ID number has been received by the system, and the radio you are paging is on the air and has received your page. 6b. The radio automatically returns to the home dis-
play PLANT POLICE AUTOMATIC MULTIPLE SITE SELECTION
(AMSS) The automatic multiple site selection (AMSS) feature extends communications beyond the reach of a single trunked site. In a system where wide-area coverage is required, multiple trunking sites are used. AMSS automatically switches the radio to a different site when the current-site signal becomes too weak. Typically, this happens when the radio is moved out of the range of one site and into the range of another. Under normal conditions, this switching is invisible to the user. Viewing the Current Site 1. 2. 3. Press the search button. If the radio is locked on a site, the display shows the current site. If the radio is scanning for a new site, the dis-
play shows SCAN-
NING until it locks on a new site. Then it shows the num-
ber of the new site. SITE 4 SCANNING SITE SITE 7 31 T R U N K E D F E A T U R E S ATS2500.book Page 32 Monday, December 18, 2000 7:39 PM Forcing a Site Change 1. Press and hold down the search button to force the change to a new site. Locking and Unlocking a Site 1. Press / until SITE is displayed. SITE PAGE CALL 2. You will hear a tone while the radio scans for a new site. 3. The radio automatically returns to the home dis-
play. 2. Press l (the softkey below SITE). SCANNING SITE 3. The current lock state is momentarily displayed. PLANT POLICE SITE LOCKED or SITE UNLOCKED 4. The display changes to LOCK UNLK 5. Press the key below the desired lock state. 6. The radio automatically returns to the home dis-
play. PLANT POLICE S E R U T A E F D E K N U R T 32 ATS2500.book Page 33 Monday, December 18, 2000 7:39 PM CONVENTIONAL FEATURES This section outlines the conventional features of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below PLANT POLICE is used to indicate the radios home display. REPEAT/DIRECT The repeat/direct feature allows you to bypass the repeater and talk directly to another portable radio. This is known as DIRECT operation. The transmit frequency is the same as the receive frequency. In REPEAT operation, you talk through the repeater, which increases the radios operating range. The transmit frequency is not the same as the receive frequency. If the repeat/direct feature is programmed to a mode, that mode operates on either direct or repeat operation. If the repeat/direct feature is programmed to the keypad, you can change the repeat/direct setting by doing the following. 1. Press / until DIR is displayed. DIR PWR PROG 2. Press l (the softkey below DIR). 3. The current talkaround state appears on the dis-
play for a few seconds. 4. Then, the display prompts for the new state. REPEATER MODE or DIRECT MODE DIR RPTR 5. Press l below the desired talkaround state: repeat (RPTR) or direct (DIR). 6. The radio returns to the home display. PLANT POLICE SMART PTT Smart PTT is a per-mode feature which gives the system manager better control of radio operators. When smart PTT is enabled in your radio, you cannot transmit on an active mode. Three radio-wide variations of smart PTT are available. Transmit Inhibit on Busy Modeyou are pre-
vented from transmitting if any activity is detected on the mode. 33 F E A T U R E S C O N V E N T O N A L I ATS2500.book Page 34 Monday, December 18, 2000 7:39 PM Transmit Inhibit on Busy Mode with Wrong Squelch Codeyou are prevented from trans-
mitting on an active mode with a squelch code other than your own. If the PL code is the same as yours, you are allowed to transmit. Note: If you try to transmit (press the PTT) on a smart PTT mode that is busy, a continuous alert tone is generated until the PTT is released; the transmission is inhibited. The red LED blinks when the radio is receiv-
Quick-Key OverrideThis feature can work in conjunction with either of the two above varia-
tions. This feature allows you to override the transmit-inhibit state by quick-keying (two PTT presses within a programmable period -- the default is one second -- of each other) the radio. ing indicating that the mode is busy. I L A N O T N E V N O C S E R U T A E F 34 ATS2500.book Page 35 Monday, December 18, 2000 7:39 PM SCAN This section outlines the scan functions of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below PLANT POLICE is used to indicate the radios home display. SCAN OPERATION The scan feature allows you to monitor activity on different conventional or trunked modes by scanning a scan list of modes. This list can be programmed with the Customer Programming Software (CPS) or user programmable. Three types of scan operation are available depending on radio model. Trunking Priority Monitor Comprises modes that are all from the same trunked system. Conventional Comprises conventional-only modes. Talkgroup Scan Comprises conventional modes and trunked modes from more than one trunking system. Priority operation is NOT available in this type of list. Your radio may support both priority and non-priority scanning. With priority scanning enabled, a scan list can have one mode assigned as the rst priority mode, and a second as the second priority mode. Automatic scanning (autoscan) can be programmed through the CPS. If autoscan is enabled for a mode, your radio begins scanning, using the modes scan list, whenever you select that mode. The radio will continue autoscanning until you select a mode that does not have autoscan enabled. Turning Scan On or OFF with the Keypad
(for Keypad radios only) S C A N 1. Press / until SCAN is displayed. 2. Press ; (the soft-
key below SCAN). PHON SCAN CALL You will see the cur-
rent scan state momentarily. SCAN ON or SCAN OFF Then ON OFF 35 ATS2500.book Page 36 Monday, December 18, 2000 7:39 PM N A C S 3. Press the softkey below the desired scan state (on or off). The radio returns to the home display. PLANT POLICE Note: The scan status annunciator, G, is dis-
played when the scan operation is active. It will be removed from the display when the scan operation is terminated. Deleting Nuisance Modes When the radio scans to a mode you do not wish to monitor (nuisance mode), you can temporarily delete that mode from the scan list. 1. When your radio is locked on the mode to be deleted, press the nuisance-mode delete button (programmed via the CPS). 2. A valid-keypress chirp is heard, indicating that the mode has been deleted. 3. The radio continues scanning the remaining modes in the list. 4. To resume scanning the deleted mode, you must leave and reenter scan operation. Note: Priority modes cannot be deleted. 36 Viewing a Scan List
(for keypad radios only) The view scan list feature allows you to view the members of the scan list associated with the currently selected mode. To view a scan list 1. Press / until VIEW is displayed. 2. Press l (the soft-
key below VIEW). 3. Press ; (the soft-
key below SCAN). The display shows the rst member of the scan list. PAGE STS VIEW PHON SCAN CALL For example FIRE DEPT 4. Every subsequent press of / will scroll through subsequent members of the scan list. 5. To leave the scan list feature, press the HOME key, or the PTT switch, or turn the mode selector knob. 6. The radio returns to the home display. PLANT POLICE ATS2500.book Page 37 Monday, December 18, 2000 7:39 PM Note: The programming-mode annunciator, K, is displayed while list view mode is active. The scan status annunciator, G, appears, indicating that a scan list is being viewed. The dot of the priority scan annunciator, H, blinks if the current displayed member of the scan list is a priority 1 mode, and is solid the cur-
rent displayed member of the scan list is a prior-
ity 2 mode. Programming a Scan List
(for keypad radios only) The program scan list feature allows you to program the members of the scan list associated with the currently selected mode. To program a scan list 1. Press / until PROG is displayed. 2. Press l (the soft-
key below PROG). 3. Press l (the soft-
key below SCAN). The display shows the current mode selected. PROG SCAN PHON CALL For example FIRE DEPT S C A N 4. Use the mode selector knob to select the required talkgroup zone. 5. Press , or / to select the required zone. If the scan status annunciator G is displayed, the mode is part of the scan list. 6. Press the select key to change the scan mode (see Scan Modes on page 38). 7. After making all the changes, select the required operating mode. 8. Press the HOME key, or the PTT switch, or turn the mode selector knob to commit all the changes made. Note: The programming-mode annunciator, K, blinks while program mode is active. The scan status annunciator, G, appears, indicating that a scan list is being viewed. The dot of the priority scan annunciator, H, blinks if the current displayed member of the scan list is a priority 1 mode, and is solid the cur-
rent displayed member of the scan list is a prior-
ity 2 mode. 37 ATS2500.book Page 38 Monday, December 18, 2000 7:39 PM Scan Modes When programming the scan list, each member can be given one of several scan modes. The following table lists the scan mode cycle activated by subsequent presses of the select key. N A C S Initial Scan Mode of Member Number of Times the Select Key is Pressed 1 2 3 4 Priority 2*
Priority 1*
Non Scan Member Scan Member Priority 2*
Priority 1*
Non Scan Member Scan Member Priority 2*
Priority 1*
Non Scan Member Scan Member Priority 2*
Priority 1*
Non Scan Member Scan Member Priority 2*
Priority 1*
Non Scan Member Scan Member
* Priority options are only available if enabled. Note: There can only be ONE Priority 1 member and ONE Priority 2 member in a scan list. Thus, if there is already a Priority 1 member in the scan list, changing another members mode to Priority 1, would automatically cause the previ-
ous members mode to be changed to a Scan Member. This same behavior is also seen when programming the Priority 2 member. 38 ATS2500.book Page 39 Monday, December 18, 2000 7:39 PM PROGRAMMING THE RADIO This section outlines the programming functions of your radio, and is only valid for Model II radios. Throughout this section, the display below PLANT POLICE is used to indicate the radios home display. Programming the Telephone List Numbers This feature lets you use the radios keypad to change the telephone numbers assigned to any of the telephone list members. Each phone number can have up to 16 digits. To change the telephone list 1. Press / until PROG is displayed. PROG 2. Press l (the softkey below PROG). 3. Press ; (the softkey below PHON). The dis-
play shows the rst pro-
grammable member of the telephone list. SCAN PHON CALL FIRE DEPT 4. Press / or ,,
or Use the keypad to enter the desired members position number (1 to 19) to view the other members of the telephone list. 5. When you stop on a member of the list, the display will alternate between showing the members name and telephone number. Alternates between POLICE DEPT and 5556213 6. Press the select key to enter edit mode. 7. A short press would enable the editing of the telephone number. The display shows the cur-
rent members telephone number. 8. A long press would enable the editing of the members name. The display shows the cur-
rent members name. 5556213 POLICE DEPT 39 R A D O I P R O G R A M M N G T H E I ATS2500.book Page 40 Monday, December 18, 2000 7:39 PM I E H T G N M M A R G O R P I O D A R 9. Use any of the alphanumeric keys to make the changes. The blinking cursor indicates the position of the next number to be added. If you require a pause in the phone dialing sequence
(to allow for a delay), you can do so by rst pressing the * key, followed by pressing the
# key. The display will show a P for pause. 10. When you have nished changing the tele-
phone number, press the select key again. The change is saved in the radios memory. 11. You are returned to step 5. The display will again alternate between show-
ing the members name and telephone number. You can now change additional numbers. Alternates between POLICE DEPT and 5556445 12. When you have nished making changes, press . to exit program mode. 13. The radio will return to the home display. PLANT POLICE Note: The programming-mode annunciator, K, blinks while program mode is active. In the edit mode, the , key functions as a backspace key. Pressing it will erase the previ-
ous digit, and the cursor will move to the left. 40 When the last digit on the display has been erased, additional presses of this key or the
/ key will cause you to leave the edit mode without making any changes. You can only enter a maximum of 16 digits in any entry for the telephone list. When this maxi-
mum is reached, the cursor will disappear. If you try to add any more digits, you will hear an invalid (bad) keypress alert tone. Programming the Call List This feature lets you use the radios keypad to change the radio ID numbers assigned to the call list used by the trunked Private Conversation and Call Alert features. Similarly, in Conventional Mode, you may change the Call List used by Stat-
Alert Selective Call and Call Alert. To change the call list radio ID numbers 1. Press / until PROG is displayed. 2. Press l (the softkey below PROG). 3. Press l (the softkey below CALL). The dis-
play shows the rst pro-
grammable member of the call list. DIR SCAN PROG SCAN PHON CALL SK TAN ATS2500.book Page 41 Monday, December 18, 2000 7:39 PM 4. Press / or ,,
or Use the keypad to enter the desired members position number (1 to 19) to view the other members of the call list. 5. When you stop on a member of the list, the display will alternate between showing the members name and radio ID number. Alternates between CT CHAN and ID: 753951 6. Press the select key to enter edit mode. 7. A short press would enable the editing of the radio ID. The display shows the current mem-
bers radio ID number. 8. A long press would enable the editing of the members name. The display shows the cur-
rent members name. ID: 753951 CT CHAN 9. Use any of the alphanumeric keys to make the changes. The blinking cursor indicates the position of the next number to be added. 10. When you have nished changing the number, press the select key again. The change is saved in the radios memory. 11. You are returned to step 5. The display will again alternate between show-
ing the members name and radio ID number. You can now change additional numbers. Alternates between CT CHAN and ID: 753853 12. When you have nished making changes, press . to exit program mode. 13. The radio will return to the home display. PLANT POLICE Note: The programming-mode annunciator, K, blinks while program mode is active. In the edit mode, the , key functions as a backspace key. Pressing it will erase the previ-
ous digit, and the cursor will move to the left. When the last digit on the display has been erased, additional presses of this key or the
/ key will cause you to leave the edit mode without making any changes. When the maximum number of digits for the radio ID is reached, the cursor will disappear. If you try to add any more digits, you will hear an invalid (bad) keypress alert tone. 41 R A D O I P R O G R A M M N G T H E I ATS2500.book Page 42 Monday, December 18, 2000 7:39 PM TELEPHONE OPERATION This section outlines the telephone operations of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below PLANT POLICE is used to indicate the radios home display. The telephone feature allows you to use your radio similar to a standard telephone. When you are dialing from the keypad, your radio may be programmed with either buffered dial (you enter all digits and press the PTT before the digits are sent out) or live dial (each digit is sent out as it is pressed). Answering a Telephone Call 1. When a telephone call is being received, you will hear telephone-type ringing. Alternates between PLANT POLICE and PHONE CALL 2. Press the pre-pro-
grammed phone button or call response button to answer the call. PHONE CALL 42 3. Carry on with your conversation in the normal manner. Press the PTT switch to talk; release the PTT to listen. 4. When you have nished your conversation, press . or the phone button to hang up. 5. The radio will return to the home display. PLANT POLICE Note: The call received status annunciator, F,
ashes when you receive a call, but is not dis-
played when you answer the call. Making a Telephone Call
(for Model II radios only) There are three phases in making a phone call, namely accessing the telephone system, sending the telephone number, having the conversation and hanging-up. Accessing the Telephone System 1. Press / until PHON is displayed. MSG SCAN PHON 2. Press l (the softkey below PHON). I E N O H P E L E T N O T A R E P O ATS2500.book Page 43 Monday, December 18, 2000 7:39 PM 3. Your radio attempts to access the telephone 6c. The telephone number will be sent out; you system. 4. If you connect successfully, you will hear a dial tone. will hear tones as they are sent. If you hear a busy signal, go to step 8 for hang-up proce-
dure. 5. The display will show the last number dialed. 5551135 Sending the telephone number using a Number on the Telephone List Sending the Telephone Number Sending the telephone number using the keypad 6a. The number can now be entered from the keypad, using any of the numeric (0 9) keys, and the * and # keys. The cursor ashes to indicate the location of the next digit to be entered. A pause can be entered in the tele-
phone number by rst pressing the * key, then the # key (Buffered dial only - The pause will be shown on the display as a P). 6b. If your radio is programmed for live dial, each digit is sent out as its key is pressed.
or If your radio is programmed for buffered dial, each digit is temporarily stored as you enter them. After entering the number, press the PTT switch to send out the number. 6a. Press , or /, to enter the telephone list. / takes you forward to the next mem-
ber of the list; , takes you backwards to the previous member of the list. 6b. Stop at the member you wish to call. 6c. The display alternates between showing the members name and telephone number. Alternates between POLICE DEPT and 5556445 6d. Press the PTT button. 6e. The telephone number will be sent out; you will hear tones as they are sent. POLICE DEPT 6f. If you hear a busy signal, go to step 8 for hang-up procedure. 43 O P E R A T O N T E L E P H O N E I ATS2500.book Page 44 Monday, December 18, 2000 7:39 PM Sending the Telephone number using a Location in the Telephone List 6a. Press , or /, to enter the telephone list. 6b. Enter the location (any preprogrammed loca-
tion from 1 through 19) of the number you wish to call. 6c. The radio will go to the selected location. 6d. The display alternates between showing the members name and telephone number. Alternates between POLICE DEPT and 5556445 6e. Press the PTT button. 6f. The telephone number will be sent out; you will hear tones as they are sent. POLICE DEPT I E N O H P E L E T N O T A R E P O 6g. If you hear a busy signal, go to step 8 for hang-up procedure. 44 Having the Conversation and Hanging Up 7. If call is answered, communicate in the normal manner. Press the PTT switch to talk; release the PTT to listen. 8. When nished with your conversation, or if the number you called is busy or does not answer, press . or the phone button to send the hang-up code. 9. The radio will return to the home display. PLANT POLICE Note: You can press the pre-programmed phone button for quick access to the telephone call fea-
ture. This will take you directly to step 3. The PLEASE WAIT message is a timed message. If you cannot access the telephone system (no dial tone heard), press . key or the phone button to hang up, and start again at step 1 of this procedure. If you are out of range of the trunked system or the phone interconnect is out of service, NO PHONE is displayed and a continuous low-
pitched tone sounds. If the trunked phone interconnect is in use, a busy tone sounds and PHONE BUSY is dis-
played. ATS2500.book Page 45 Monday, December 18, 2000 7:39 PM When the maximum number of digits have been entered (buffered dial only), the cursor will disappear. In the edit mode, the , key functions as a backspace key. Pressing this key erases the last digit entered, and moves the cursor to the left. When the last digit on the display is erased, additional presses of this key causes the last member of the preprogrammed telephone list to be displayed; pressing the / key displays the
rst member of the list. After reaching the number you are calling, you may need to dial an extension number before you can reach your party. Here, enter the extension number from the keypad or (if so pro-
grammed) use the arrow keys to nd the exten-
sion number in the telephone list. If you have live dial, the number is sent as the keys are pressed. If you have buffered dial, press the PTT switch again to send out the extension number. Motorola trunked systems and many conven-
tional telephone patches generate a high-
pitched go-ahead tone when the radios PTT switch is released. This is heard by the land-line party and is an indicator to begin talking. The conventional telephone feature allows you to use your conventional radio similar to a standard telephone. To make a call through the telephone system, your radio must send access and hangup codes to the system. Unless other-
wise indicated, the conventional telephone sec-
tions in this manual assume that the access and hangup codes have been programmed into the radio by the RSS. These codes will then be auto-
matically transmitted. O P E R A T O N T E L E P H O N E I 45 ATS2500.book Page 46 Monday, December 18, 2000 7:39 PM SPECIAL FEATURES This section outlines some of the special features that can be congured for your radio. However, not all models come equipped with these features. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below PLANT POLICE S E R U T A E F L A C E P S I is used to indicate the radios home display. EMERGENCY OPERATION Pressing the top emergency button (for radios with emergency operation) sends out an emergency signal, which takes precedence over any other signalling activity in progress. This emergency signal can take two forms: emergency alarm and emergency call. Your radio can have either or both signal types enabled. The emergency alarm feature alerts the dis-
patcher, who is using a special terminal, to an emergency condition and identies the unit sending the emergency signal. The emergency call (radios with trunked emer-
gency operation only) is a type of dispatch oper-
ation which gives your radio priority access. Emergency call is programmable for either tacti-
cal or non-tactical operation. Tactical emergency 46 operation places the call to the currently selected mode; non-tactical operation places the call to a predetermined emergency mode.
Emergency signals a critical situation. It should NEVER be used for any other reason. Sending an Emergency Alarm 1. Press and hold the Alternates between emergency button (the length of button press is programmable by the CPS). EMERGENCY and PLANT POLICE 2. A short, medium-pitched emergency tone sounds, indicating entry into emergency operation. 3. When the trunked emergency alarm is acknowledged by the central controller, the radio sounds ve beeps and the alarm ends. 4. The radio returns to normal operation or, if enabled in your radio (trunked emergency call systems only), enters into emergency call operation. 5. While in emergency call operation, subse-
quent presses of the emergency button will re-initiate the emergency sequence. ATS2500.book Page 47 Monday, December 18, 2000 7:39 PM Sending a Silent Emergency Alarm 1. In radios with the silent emergency alarm option enabled, pressing the emergency but-
ton sends an emergency signal to the dis-
patcher. Note: Pressing the PTT switch while the radio is in emergency alarm operation will place the radio in emergency call operation if emergency call is enabled. Sending an Emergency Call 2. During the emergency alarm procedure: the 1. Press the emergency Alternates between LED will not light, tones will not sound, and the display will not change. button. I S P E C A L F E A T U R E S 3. The audio is muted (turned off), and will remain so until you exit the emergency state. Canceling an Emergency Alarm 1. Press the emergency button for more than 11/2 seconds (programmable by the CPS). 2. A medium-pitched emergency-exit tone sounds until the button is released and the radio returns to normal operation. The alarm can also be canceled (without sounding the emergency-exit tone) by:
pressing the PTT switch (see following note), turning the radio off, or receiving an acknowledge from the dispatcher. EMERGENCY and PLANT POLICE 2. A short, medium-pitched emergency tone sounds. 3. Press the PTT switch requesting a priority mode assignment in the trunked system. 4. While the radio is in emergency call operation, it operates in the usual dispatch manner. Note: The mode you use during an emergency is controlled by whether your radio is programmed for tactical or non-tactical operation. If tactical, you will be talking to the mode you selected before entering emergency call; if non-tactical, you will talk to a preprogrammed emergency mode. 47 S E R U T A E F L A C E P S I ATS2500.book Page 48 Monday, December 18, 2000 7:39 PM If you change modes while in emergency call operation, the emergency call is moved and con-
tinued on the new mode. Ending an Emergency Call It is important that you exit the emergency call mode when you have nished your emergency call. The dynamic regrouping feature allows the dispatcher to temporarily reassign selected radios, operating in the same or different trunked modes, to a single special mode so that they can communicate with each other. This feature, enabled in each radio via the CPS, is typically used during special operations. When your radio has been dynamically regrouped, you will hear a distinct gurgle tone. 1. Press the emergency button for more than 1 1/2 seconds (programmable by the CPS). Mode Selection 2. You will hear a medium-pitched emergency-
exit tone until the emergency button is released, and the radio will return to normal operation. Emergency with Voice to Follow This feature (aka Hot Microphone) places your radio in a transmit mode for a preprogrammed period of time
(programmable by CPS) after the emergency alarm is activated. During this time period, voice transmissions can be made without pressing the PTT. After this transmit time has expired, the unit will revert back to receive mode. Normal operation resumes, and the user is required to press PTT for any further transmissions on that emergency channel. DYNAMIC REGROUPING You will not notice whether your radio has this feature enabled until a dynamic regrouping is sent by the dispatcher. If you turn your radios mode selector knob to the dynamic regrouping position without being dynamically regrouped, an invalid-mode tone will be heard. You can select the dynamic regrouping position using the menu on the display (Model II radios only) or using the mode selector knob. To do this with the mode selector knob 1. When your radio is dynamically regrouped, you will hear a gurgle tone. 2. Your radio is automatically switched to the dynamic regrouping mode. The display shows the name assigned to the dynamic regrouping mode. 48 I S P E C A L F E A T U R E S ATS2500.book Page 49 Monday, December 18, 2000 7:39 PM 3. Turn the mode selector knob to the dynamic regrouping position to transmit on the dynamic regrouping mode. 4. Talk and listen as usual. 5. When the dynamic regrouping is canceled by the dispatcher:
a. If the mode selector knob is in the dynamic regrouping position, an invalid-mode tone is heard until a normal mode is selected. b. If the mode selector knob is in any other mode position, the radio will transmit in the selected mode. Note: Until you select the correct mode position, you will hear a gurgle tone each time you press the PTT switch, reminding you that you are transmitting on the dynamic regrouping mode, not the mode indicated by the position of the mode selector knob. Select Enable and Disable The dispatcher may classify regrouped radios into either of two categories: select enabled, and select disabled. Select Enabled Select Dis-
abled These radios are free to make mode changes to any available mode, including the dynamic regrouping mode. These radios cannot change modes, since the dispatcher has specically chosen to force the radio to remain in the dynamic mode. Scan, Phone, and Private Conversation cannot be selected while the radio is select disabled. 49 ATS2500.book Page 50 Monday, December 18, 2000 7:39 PM I E N O Z T R A M S N O T A R E P O 3. Automatic Site Registration/De-registration SmartZone radios automatically send in their unit IDs and current mode selections upon power up, power down, site switches, mode changes, and when they exit emergency operation. This allows the zone controller to know where the radio is at all times, and what mode the radio has selected. 4. Critical Site Assignment One or more sites can be designated as critical sites. This instructs the zone controller to ensure that every site designated as a critical site must have available channel resources, before a chan-
nel is given to a radio wishing to be identied as a critical site user. Otherwise a busy will be sent to the unit. 5. Busy Override This feature allows a SmartZone radio to send a busy override request if a busy is issued. The zone controller sends a grant even though not all of the sites may have available channel resources. SMARTZONE OPERATION This section outlines the SmartZone operations of your radio. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below PLANT POLICE is used to indicate the radios home display. BENEFITS OF SMARTZONETM Radios that operate in a SmartZone system enjoy the benets that SmartZone brings over AMSS operation. Like AMSS, SmartZone is a wide-area coverage system that allows multiple sites to be operational in the system. SmartZone brings several enhancements over AMSS operation, as in the following. 1. Dynamic Site Assignment Allows the zone controller to dynamically assign channels at sites where required, as opposed to bringing up channels at all of the sites as AMSS systems do. 2. Variable Density Sites SmartZone allows sites to have varying numbers of channel resources to accommodate low-density areas as well as high-density areas. 50 ATS2500.book Page 51 Monday, December 18, 2000 7:39 PM 6. Enhanced Automatic Site Switching SmartZone radios will use RSSI (received signal strength indication) to determine if the radio should switch to another site. This is transparent to the user. In addition, the zone controller contin-
uously transmits adjacent site information to the radios, so that the radio, at any time, is able to quickly switch to the next site that has the highest RSSI rating. This is an enhancement over AMSS systems. 7. Preferred Site SmartZone radios can program certain sites to be always preferred, most preferred, or least pre-
ferred. This gives the user the exibility to keep a radio on a particular site, regardless of the pres-
ence of a stronger signal from an adjacent site. This also forces the radio to always look for its pre-
ferred site and use it whenever possible. 8. Site Trunking If the zone controller loses communication with any site, that site will revert to what is known as
site trunking. While in this condition, radios are still able to operate in the trunking mode, but trunking operations are limited to the site only. 9. Enhanced Failsoft Operation If a site experiences a complete failure, it will revert to failsoft operation like todays SMARTNET system. A SmartZone radio, however, can be pro-
grammed to automatically migrate to the lowest failsoft frequency programmed in its list of 32 con-
trol modes. The radio will periodically scan the control mode to check for the presence of a valid control mode (in case the radio roamed into a site which is trunking). Site Switching in SmartZone Site Switching in SmartZone mainly uses signal strength to determine whether or not to switch sites. Other factors used are the radios preferred site selection, and whether the radio is site locked or not. Because the radio knows the site ID, active control mode, and the signal strengths of its adjacent sites, the radio is capable of quickly switching sites. 51 O P E R A T O N S M A R T Z O N E I ATS2500.book Page 52 Monday, December 18, 2000 7:39 PM I E N O Z T R A M S N O T A R E P O 3. When a new site is found, the new sites name will be momentarily displayed if it is known, otherwise SITE XX Locking and Unlocking a Site As in an AMSS radio, you can force the radio to stay locked onto a site, regardless of whether the signal level of an adjacent site is higher or not. Of course, locking a radio onto a particular site defeats the automatic site switching mechanisms of the radio. However, you can still force the radio to scan to another site while site locked. The radio automatically becomes site locked to the next site it nds. Refer to Locking and Unlocking a Site on page 32 to change the radios locked state. Preferred Site Selection SmartZone radios can have up to eight sites that are individually set as either always preferred, most preferred, or least preferred. The default value is no preference. This feature is programmed via the CPS. Viewing the Current Site 1. Press the search button. a. b. If the radio is presently locked on a site, the display shows either the name of the current site or the site number. If the radio is scanning for a new site, the dis-
play shows SCANNING SITE until it locks onto a new site. This is a timed display which disappears after a few seconds. c. If the radio has not received a site ID, the radio displays SITE XX until either the display times out or the radio receives the site ID. Forcing a Site Change 1. Press and hold down the search button to force the change to a new site. 2. You will hear a tone and the display shows SCANNING SITE while the radio scans for a new site. 52 ATS2500.book Page 53 Monday, December 18, 2000 7:39 PM Always-Preferred Site A SmartZone radio always attempts to stay on this site whenever possible unless the receive signal strength indication (RSSI) level falls below the unacceptable level. The radio periodically checks the RSSI levels of its preferred site(s) to ensure that it always operates on the best preferred site
(more than one preferred site can be enabled). Most-Preferred Site A site marked in this fashion is one level of prefer-
ence below always preferred. The radio attempts to remain on this site unless an always-preferred site is determined to have either the same or a higher RSSI level. The radio always determines the best most-preferred site and switches to it whenever possible. Non-Preferred Site A radio operating in this site switches sites if an always preferred or most-preferred adjacent site with the same or higher RSSI level is discovered. The radio always determines the best non-pre-
ferred site and switch to it whenever possible. Least-Preferred Site A radio operating in this site switches sites if any of the above site rankings for any adjacent sites are discovered and their RSSI levels are at least at the acceptable range. The unit always determines the best least-preferred site and switch to it when-
ever possible. Busy Override With the introduction of dynamic site assignment, critical site, and critical user concepts in SmartZone, the busy processing rules were changed to allow users to communicate with some of the trunked mode members instead of waiting for all trunked mode members in all sites to be available. A busy override request can be made to request for the grant, even though one or more non-critical states are busy. Busy override is not a radio codeplug option but is enabled or disabled via the SmartZone manager. After you have requested a mode by pressing the PTT, and have received a busy indication 1. Release the PTT and press it again. A busy indication will be received if still busy. 53 O P E R A T O N S M A R T Z O N E I 1. When a site goes into site trunking, the radio receives this indication and displays. SITE TRUNKING 2. The display will alternate between the current trunked mode and the site trunking display for as long as the radio remains in site trunking. 3. The radio will not be considered in site trunking if:
a. The zone controller determines that the site should no longer be in site trunking and the radio receives this indication, or b. the radio is out of range, or c. the radio enters failsoft operation. ATS2500.book Page 54 Monday, December 18, 2000 7:39 PM 2. Keep the PTT switch pressed for the amount of time specied in the codeplug for busy over-
ride delay time (typically about three seconds, but can range from two to six seconds). 3. After the timer times out, if the PTT is still pressed, the busy override request is sent. 4. A programmable busy override chirp acknowl-
edgement is heard. 5. I E N O Z T R A M S N O T A R E P O If a grant is received, you should note that not all of the members of the mode are engaged in the call. You will not be able to determine this. More sites may join the call, however, if mem-
bers become available at these sites and the original call is still active. Site Trunking Site trunking occurs when a site is no longer able to participate in wide-area calls controlled by the zone controller. Radios operating in site trunking can only communicate with other radios at that site. All trunking features are still available. The radio will always be looking for a wide-area trunking site to lock onto if it roams into range of one. 54 ATS2500.book Page 55 Monday, December 18, 2000 7:39 PM STAT-ALERT FEATURES This section outlines the Stat-Alert features of your radio. Stat-Alert is an option which you can enable for your radio. Please see your dealers for more information. All references to what is shown on the display is only valid for Model II radios. Throughout this section, the display below PLANT POLICE is used to indicate the radios home display. VIEWING YOUR RADIOS ID NUMBER To view your radios ID number 1. Press / until CALL is displayed. ZONE MUTE CALL 2. Press l (the softkey below CALL). 3. The display shows the last ID number transmit-
ted or received. 4. Press ,. 5. The display shows the last Group ID number transmitted or received. ID: 1048 GROUP: 105 6. Press ,. 7. The display shows your radios ID number. MY ID:1048 8. Press ,. 9. The display shows your radios Group ID number. 10. Press . to return the radio to the home dis-
play. MY GRP:001 PLANT POLICE Note: If your radio has been so programmed, you can press the call button for quick access to viewing your radios ID number. This takes you directly to step 3. STAT-ALERT VOICE SELECTIVE CALL OPERATION This feature provides a convenient way for a dispatcher to voice page an individual or group. Voice selective call decode also eliminates the need for you to listen to trafc that is of no concern to you. This is a per-radio feature, enabled on a per-mode basis, and available as individual call or group call. Voice Selective Call is another method of unmuting a radio other than PL codes. Radios with Voice F E A T U R E S S T A T
A L E R T 55 ATS2500.book Page 56 Monday, December 18, 2000 7:39 PM Selective Call may be programmed to unmute one of two ways:
1. (OR muting option) upon receiving proper PL code or a Selective Call, or 2. (AND muting option) upon receiving both proper PL code and Selective Call Receiving a Voice Selective Call 1. When a call is received, the green LED
ashes, and a one-time, two-beep alert tone is emitted; on the display, the call-received status annunciator (F) ashes. A voice message will follow. 2. The display shows the incoming callers ID number momentarily. ID: 2350 3. Return the radio back to voice selective call operation by pressing the monitor button, or if so programmed, the radio can automatically reset to voice selective call. 4. The radio will return to the home display. PLANT POLICE Note: After answering a Voice Selective Call, the callers ID number is stored in your radio as the
last ID number received. 56 T R E L A
T A T S S E R U T A E F Two automatic-reset features are available for voice selective-call. These features reset the radio to voice selective call when the automatic reset timer expires. 1. Automatic Reset Without Carrier Override The automatic-reset timer will start after the last voice message is completed, or after the radio is dekeyed (you released the PTT switch). 2. Automatic Reset With Carrier Override When a carrier is detected, the automatic reset timer will stop; when the carrier is lost, the automatic-reset timer will start over. Voice selective call automatic reset is can-
celled when the monitor button is pressed, or when the mode is changed. The automatic-reset timer is started over if it was running when either a voice selective call was again decoded or a successful transmission was completed. Making a Voice Selective Call There are four phases in making a Voice Selective call, namely initiating a Voice Selective call, entering the desired radio ID number, sending the radio ID number, and having the conversation. ATS2500.book Page 57 Monday, December 18, 2000 7:39 PM Initiating a Voice Selective Call 1. Press / until CALL is displayed. ZONE MUTE CALL 2. Press l (the softkey below CALL). 3. The display shows the last ID number transmit-
ted or received. ID: 2350 Entering the Desired Radio ID Number If the last ID number called is the desired number, go directly to step 5. To enter a new number 4a. Enter the new four-digit ID number using the keypad. 4b. On the display, the old ID number disappears and the new digits appear as they are being entered. 4c. The cursor ashes indicating the location of the next number to be entered. Note: Once you have started entering numbers, the , key functions as a backspace key. Pressing it causes the last digit entered to be erased, and the cursor moves to the left. When the last digit is erased, an additional press of this key causes the last ID number transmitted or received to be displayed; pressing / shows the rst member of the list. If automatic Selective Call is enabled, your radio will remain in Selective Call until you exit the mode. If automatic Selective Call is disabled in your radio, the radio will immediately exit Selective Call when you release the PTT. In both Selective Call and Call Alert, a * will match any number in the ID position. For exam-
ple, paging ID 000* will page all IDs from 0000-
0009. Paging **** will page all radios on the sys-
tem. To enter a number from the call list 4a. Press either , or /. 4b. / takes you forward to the rst or next member of the list; , takes you backwards to the last or previous member of the list. 4c. When at a member of Alternates between the list, the display alter-
nates between showing the members name and ID number. CK TANG and ID: 2350 F E A T U R E S S T A T
A L E R T 57 ATS2500.book Page 58 Monday, December 18, 2000 7:39 PM To enter a number from a location in the call list Sending the Radio ID Number 4a. Press either , or / to enter the call list. 4b. Enter the rst digit of the location number. If there are fewer than 10 members in the list, go directly to step 4e. 4c. If there are 10 or more members in the list, the display shows ID LOC#X_ (where X is the rst digit). The cursor blinks to show the location of the second digit. 4d. Enter the second digit of the location number. 5. Press the PTT switch to transmit the ID num-
ber. If enabled, an alert tone will sound during the transmission of the radio ID number. After the alert tone, you may talk. STAT-ALERT CALL ALERT OPERATION Stat-Alert Call Alert is a per-radio feature that provides a convenient way for the dispatcher to page you through your radio. This is especially useful in noisy environments, or when you need to be away from your radio equipment. Alternates between Receiving a Call Alert Page 4e. The radio goes to that position in the list. The display alternates between showing the members name and ID number. CK TANG and ID: 2350 T R E L A
T A T S S E R U T A E F Note: The last member of the list is also the last ID transmitted or received at position 00 on the list. If you enter a location number that does not exist (for example, 15), the display will show
INVALID ENTRY, and the radio will sound an invalid-keypress tone and return back to step 4b of this procedure. 58 1. Upon receiving a Call Alert page, four alert tones sounds (repeats every 5 seconds). 2. The green LED lights up and the Call Received annunciator, F, blinks indicating a call is received. 3. The display will show the Caller ID, and then alternates between the home display, and
PAGE RECEIVED. 4. Press the PTT switch to answer the page. You may have to make a voice selective call, if the radio that paged you is on selective call mode. ATS2500.book Page 59 Monday, December 18, 2000 7:39 PM 5. The display shows the current mode. The audi-
ble alert, LED and call received annunciator turns off. FIRE DEPT 6. The ID number of the radio that paged you is stored as the last ID number received. Note: The green ashing LED, alert tone, and
ashing annunciator will continue until the Call Alert is acknowledged (press PTT, or press and release the monitor button). Making a Call Alert There are three phases in making a call alert, namely initiating a call alert, entering the radio ID number that you wish to page, and sending the call alert. Initiating a Call Alert 1. Press / until PAGE is displayed. 2. Press l (the softkey below PAGE). PAGE PHON VIEW 5a. 3. The display shows the last ID number transmit-
ted or received. ID: 2350 Note: The same list is shared by both Call Alert and Select Call features. If your radio has been so programmed, you can press the page button for quick access to the Call Alert feature. This will take you directly to step 3. Entering the Radio ID Number that you wish to Page The procedure for entering the Radio ID Number is exactly the same as the process outlined in the Select Call section. Please refer to Entering the Desired Radio ID Number on page 57. Sending the Call Alert 4. Press the PTT switch to transmit the ID num-
ber. If the page is unsuccessful If the called radio fails to acknowledge the alert, a low-pitched alert tone sounds and the display changes to NO ACKNOWLEDGE. 59 F E A T U R E S S T A T
A L E R T RADIO CHECK This feature allows the dispatcher to determine if a radio unit is on the air without disturbing the radio operator. This is a useful tool for the radio dispatcher to use for routine maintenance checks, or if there is reason to doubt the availability of a radio unit. When the dispatcher "checks" for the radio, the radio will receive the command and automatically acknowledge it. The transmit (red) LED will light when the radio sends the acknowledgement. EMERGENCY OPERATION Please refer to Emergency Operation on page 46. ATS2500.book Page 60 Monday, December 18, 2000 7:39 PM 5b. Press the PTT switch to send the ID number again, or press . to hang up and return to the home display. If the page is successful 5a. If you hear ve beeps, the radio you are pag-
ing is on the air and has received your page. 5b. The radio automatically returns to the home dis-
play PLANT POLICE PTT-ID Stat-Alert PTT-ID is a per-mode feature describing an identication code transmission that is tied to the PTT switch. The ID code is automatically sent every time a voice transmission occurs (that is, the PTT switch is pressed). When PTT-ID comes before the voice transmission, you will hear a tone until the ID transmission is completed; this helps you avoid talking while the ID code is being transmitted. This tone can be disabled on a per-radio basis. Also, the ID code transmission can be programmed to follow the voice transmission. 60 T R E L A
T A T S S E R U T A E F
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2007-04-06 | 851 ~ 870 | TNF - Licensed Non-Broadcast Transmitter Held to Face | Class II permissive change or modification of presently authorized equipment |
2 | 2005-11-07 | 851 ~ 870 | TNF - Licensed Non-Broadcast Transmitter Held to Face | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2007-04-06
|
||||
1 2 |
2005-11-07
|
|||||
1 2 | Applicant's complete, legal business name |
Motorola Solutions, Inc.
|
||||
1 2 | FCC Registration Number (FRN) |
0003778479
|
||||
1 2 | Physical Address |
8000 West Sunrise Blvd
|
||||
1 2 |
Ft Lauderdale, Florida 33322
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
t******@timcoengr.com
|
||||
1 2 |
T******@TIMCOENGR.COM
|
|||||
1 2 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
AZ4
|
||||
1 2 | Equipment Product Code |
89FT5837
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
D******** Z******
|
||||
1 2 | Title |
Regulatory Compliance Manager
|
||||
1 2 | Telephone Number |
95472********
|
||||
1 2 | Fax Number |
--********
|
||||
1 2 |
d******@motorolasolutions.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 | Yes | |||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | TNF - Licensed Non-Broadcast Transmitter Held to Face | ||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | ATS2500, PMUF1063B, 1064B | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 | Original Equipment | |||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Power listed is conducted. SAR compliance for body-worn operations is restricted to belt-clips, holsters and accessories supplied or designated for this product, and to belt-clips, holsters, or similar accessories that have no metallic component in the assembly and which provide at least 2.5 cm separation between the device, including its antenna and the users body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50%. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration to comply with the Occupational/Controlled MPE limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR values are: Body: 4.79 W/kg for 50% Duty Cycle, Head: 1.83 W/kg for 50% Duty Cycle. CLASS II CHANGE: This Class II Change adds alternate components for compliance with the RoHS requirements. No other changes. Output power is continuously variable from the value listed to 1W. | ||||
1 2 | Power listed is conducted. SAR compliance for body-worn operations is restricted to belt-clips, holsters and accessories supplied or designated for this product, and to belt-clips, holsters, or similar accessories that have no metallic component in the assembly and which provide at least 2.5 cm separation between the device, including its antenna and the users body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50%. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration to comply with the Occupational/Controlled MPE limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR values are: Body: 4.79 W/kg for 50% Duty Cycle, Head: 1.83 W/kg for 50% Duty Cycle. Output power is continuously variable from the value listed to 1W. | |||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Motorola
|
||||
1 2 | Name |
W******** E****
|
||||
1 2 | Telephone Number |
954-7********
|
||||
1 2 | Fax Number |
954-7********
|
||||
1 2 |
F******@motorolasolutions.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 9 | 806 | 824 | 2.95 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 2 | 9 | 851 | 870 | 2.95 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 9 | 806 | 824 | 2.95 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
2 | 2 | 9 | 851 | 870 | 2.95 | 1.5 ppm | 16K0F3E |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC