FCC ID: AZ492FT5865 Mobile 2-Way Radio

 

APXTM TWO-WAY RADIOS APX MOBILE O2 CONTROL HEAD USER GUIDE m ASTRO APX O2 Control Head Mobile Radio Quick Reference Card RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Stations ATTENTION!

This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Station which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. Radio Controls LED Indicators Power Button Up & Down Buttons*

Emergency Button*

Multi-function Knob

(MFK)*

Home Button Dimmer Button Menu Select Buttons*

Accessory Port (Microphone)

*These controls/buttons are programmable. Radio On/Off Press the Power button to turn the radio on or off. Adjusting Volume If volume is set as the primary mode, 1 Turn the MFK clockwise to increase volume or counterclockwise to decrease the volume. If volume is not set as the primary mode, press the MFK once and repeat step 1. Selecting a Zone If zone is set as the primary mode, 1 Turn the MFK until the display shows the desired zone and press the PTT button to begin transmitting on the displayed zone. If zone is not set as the primary mode, press the MFK once and repeat step 1. OR 2 > or < (on the keypad mic.) to scroll to Zone. 3 Press the Menu Select button directly below Zone. 4 Rotate the MFK or D or U to the desired zone. 5 Press the Menu Select button directly below Sel or the button (on the keypad mic.) to confirm the selected zone number. 6 Press the PTT button to begin transmitting on the displayed zone. Selecting a Channel If channel is set as the primary mode, 1 Turn the MFK until the display shows the desired channel and press the PTT button to begin transmitting on the displayed channel. If channel is not set as the primary mode, press the MFK once and repeat step 1. OR 2 > or < (on the keypad mic.) to scroll to Chan. 3 Press the Menu Select button directly below Chan. 4 Rotate the MFK or press D or U to the desired channel. 5 Press the Menu Select button directly below Sel or the button (on the keypad mic.) to confirm the channel. 6 Press the PTT button to transmit on the displayed channel. Receiving and Transmitting 1 Take the microphone off the hook. 2 Select zone/channel. 3 Listen for a transmission. OR

> or < (on the keypad mic.) to Mon then press the Menu Select button directly below Mon and listen for activity. 4 Adjust volume, if necessary. 5 Press the PTT button to transmit; release to receive. Sending an Emergency Alarm 1 Press the Emergency button. A tone sounds and the display alternates Emergency and the home display. 2 A dispatcher acknowledgment Ack received display follows. AND, Trunking Only:

A high-pitched tone indicates that the alarm has been received by the trunked systems central controller. To exit emergency at any time, press and hold the Emergency button or the PTT button.

*PMLN6193C*

PMLN6193C English MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. 2012, 2013 by Motorola Solutions, Inc. All Rights Reserved. 06/13 1303 East Algonquin Road, Schaumburg, Illinois 60196, U.S.A. Sending an Emergency Call (Trunking Only) 1 Press Emergency button. 2 A tone sounds and the display alternates Emergency and the home display. OR A short low-pitched tone sounds when the selected channel does not support emergency. 3 Press and hold the PTT button. Speak clearly into the microphone. 4 Release the PTT to end the transmission. To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Alarm 1 Press the preprogrammed Emergency button to activate the silent alarm feature. 2 The display does not change; the LED does not light up, and there is no tone. If silent emergency alarm is used with emergency call, pressing the PTT button exits the silent mode and initiates the emergency call. Receiving a call or data. Display Status Icons u t F V Transmitting a call or data. Received an Individual Call. The more stripes, the stronger the signal strength for the current site (trunking only). m l G n o O Direct radio-to-radio communication or communication through a repeater. On = Direct Off = Repeater M K HOR . i j k This channel is being monitored. Voice muting the affiliated trunking talkgroup or selected channel. On = Enabled Off = Disabled L = Radio is set at Low power. H = Radio is set at High power. Scanning a scan list. Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority-

Two Channel during scan. The vote scan feature is enabled. Menu Navigation

< or > to Menu Entry

(on the keypad mic.). On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On = AES Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On = Location feature enabled, and location signal available. Off = Location feature disabled. Blinking = Location feature enabled, but location signal unavailable. Inverted = User is currently associated with the radio. On = Packet data is activated. Off = Packet data is deactivated. Blinking = Device registration or user registration with the server failed due to an invalid username or pin. Data activity is present. MFK is in Mode Change feature Turn the MFK to change channel. MFK is in Volume Change feature Turn the MFK to adjust the volume. g directly below Menu Entry to select. U or D to scroll through sub-list. H to exit. g directly below Menu Entry to select. English Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola Solutions, Inc. Address: Motorola Solutions, Inc., 1303 East Algonquin Road Schaumburg, IL60196, U.S.A. Phone Number: 1-800-927-2744 Hereby declares that the product:

Model Name: APX Mobile conforms to the following regulations:

FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital Device As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. D e c l a r a t i o n o f C o n f o r m i t y i English Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. y t i m r o f n o C f o n o i t a r a l c e D ii English Additional FCC Notes to Users The following FCC information applies to Bluetooth radio options IC Model Name: PMHN4193A Description: O2 Bluetooth Option Board FCC ID: AZ492FT6002 IC: 109U-92FT6002 Conforms to the following regulations: FCC Part 15, Section 15.19, 15.12, and 15.105 Note: Changes or modifications not expressly approved by Motorola may void the users authority, as authorized by the FCC, to operate this device and should not be made. See 47 CFR Part 15.21. Information to user.The users manual or instruction manual for an intentional or unintentional radiator shall caution the user that changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. See 47 CFR Part. 15.19(3). This device has been tested and found to comply with the limits of Part 15.15 of the FCC rules. Parties responsible for equipment compliance should note that the limits specified in this part will not prevent harmful interference under all circumstances. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. See Part 15.105b These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. D e c l a r a t i o n o f C o n f o r m i t y iii English However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Industry Canada (IC) Statements:

This Class B digital apparatus complies with ICES-003 and Radio Standards Specification (RSS) 210. y t i m r o f n o C f o n o i t a r a l c e D iv English Contents Declaration of Conformity . i Important Safety Information. ix RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Stations . ix Software Version . x Notice to Users (FCC and Industry Canada) . x Informations importantes sur la scurit . x GUIDE SUR LEXPOSITION AUX RADIOFRQUENCES ET LA SCURIT DU PRODUIT POUR RADIOS MOBILES BIDIRECTIONNELLES. x Version du logiciel . xi Avis aux utilisateurs (FCC et Industrie Canada) . xi Computer Software Copyrights. xii C o n t e n t s Documentation Copyrights. xii Disclaimer. xii Getting Started. 1 How to Use This User Guide . 1 Notations Used in This Manual . 1 Additional Performance Enhancement . 2 Dynamic System Resilience (DSR) . 2 CrossTalk Prevention . 2 Encrypted Integrated Data (EID) . 2 SecureNet. 2 P25 Digital Vehicular Repeater System (DVRS) . 2 What Your Dealer/System Administrator Can Tell You. 3 Preparing Your Radio for Use . 3 Turning On the Radio. 4 Validating Compatibility During Power Up . 4 Adjusting the Volume . 5 Identifying Radio Controls . 5 Radio Parts and Controls. 6 O2 Control Head and Microphone . 6 v English Programmable Features . 7 One Touch Button . 7 Assignable Radio Functions . 7 Assignable Settings or Utility Functions . 9 Accessing the Preprogrammed Functions . 10 Using the Menu Select Buttons . 10 Using the Advance Programmable Buttons. 11 Using the Navigation Buttons . 11 Home Button . 12 Dimmer Button . 12 Multi-function Knob. 12 The MFK button on your radio is programmable to the following features : . 12 Using the Keypad . 14 Keypad Characters Uppercase Mode . 14 Keypad Characters Lowercase Mode . 15 Keypad Characters Numeric Mode . 16 Keypad Characters Hexadecimal Mode . 17 Push-To-Talk (PTT) Button . 18 Identifying Status Indicators . 18 Status Icons. 19 Text Messaging Service (TMS) Icons . 21 Status Icons. 21 TMS Menu Options . 22 s t n e t n o C vi English Call Type Icons . 23 LED Indicator . 24 Multi-function Knob - Concentric Ring LED . 24 Intelligent Lighting Indicators . 25 Alert Tones . 26 General Radio Operation . 31 Selecting a Zone . 31 Selecting a Radio Channel . 32 Receiving and Responding to a Radio Call. 32 Receiving and Responding to a Talkgroup Call . 33 Receiving and Responding to a Private Call (Trunking Only). 33 Receiving and Responding to a Telephone Call . 34 Making a Radio Call . 35 Making a Talkgroup Call . 35 Making a Private Call (Trunking Only) . 36 Making a Telephone Call . 37 Repeater or Direct Operation . 37 Monitoring Features . 38 Monitoring a Channel . 38 Conventional Mode Operation . 39 Advanced Features. 40 Advanced Call Features. 40 Calling a Phone Not in the List. 40 Receiving and Making a Selective Call (Conventional Only). 41 Receiving a Selective Call. 41 Making a Selective Call. 41 Using the Talkgroup Call Feature (Conventional Operation Only) . 42 Selecting a Talkgroup . 42 Sending a Status Call. 43 Using the Dynamic Regrouping Feature (Trunking Only) 44 Requesting a Reprogram . 44 Classifying Regrouped Radios . 45 Contacts. 45 Making a Private Call from Contacts . 46 Adding a New Contact Entry . 47 Deleting a Contact Entry . 48 Adding a Contact to a Call List or Phone List. 49 Editing a Contact in a Call List or a Phone List . 49 Editing an Entry Alias . 49 Editing as Entry ID . 50 Editing a Call Type . 51 Scan Lists . 51 Viewing a Scan List . 51 C o n t e n t s Editing the Scan List . 52 Changing the Scan List Status . 52 Viewing and Changing the Priority Status . 53 Scan. 53 Turning Scan On or Off. 53 Turning Scan On While Disregarding the Squelch Code

(Conventional Channels Only) . 54 Transmitting While the Scan is On . 54 Radio Programmed for Talkback Scan . 54 Radio Programmed for Non-Talkback Scan . 55 Deleting a Nuisance Channel . 55 Restoring a Nuisance Channel . 55 Changing Priorities Status While Scan is On . 56 Restoring Priorities in a Scan List. 56 Hang Up Box (HUB) . 56 Call Alert Paging . 57 Receiving a Call Alert Page . 57 Sending a Call Alert Page. 58 In-Call User Alert . 59 Emergency Operation . 59 Sending an Emergency Alarm . 60 Sending an Emergency Call (Trunking Only) . 60 Sending an Emergency Alarm with Emergency Call60 Sending a Silent Emergency Alarm . 61 Special Considerations for Emergencies . 62 vii English Automatic Registration Service (ARS) . 63 Selecting or Changing ARS Mode. 63 Accessing the User Login Feature . 64 Logging In as a User . 64 Logging Out . 65 Text Messaging Service (TMS). 66 Accessing TMS Feature . 66 Composing and Sending a New Text Message . 67 Sending a Quick Text Message. 68 Using the Priority Status and Request Reply Features 70 Appending or Removing a Priority Status to a Text Message . 70 Appending or Removing a Request Reply to a Text Message . 70 Appending a Priority Status and a Reply Request to a Text Message . 70 Removing a Priority Status and a Reply Request from a Text Message . 71 Managing Text Messages . 71 Receiving a Text Message . 71 Viewing a Text Message from the Inbox. 72 Replying to a Received Text Message . 73 Accessing the Drafts Folder . 74 Managing Sent Text Messages . 74 Viewing a Sent Text Message . 74 Sending a Sent Text Message . 75 s t n e t n o C viii English Deleting Text Messages . 76 Secure Operations . 76 Managing Encryption . 76 Loading a Single Encryption Key . 76 Loading the Group Encryption Keys . 77 Using the Multikey Feature . 77 Selecting an Encryption Key (Conventional Only). 78 Enabling Secure Transmission . 78 Accessing the Secure Feature . 79 Selecting a Keyset. 79 Erasing the Selected Encryption Keys . 79 Requesting an Over-the-Air Rekey . 80 MDC Over-the-Air Rekeying (OTAR) Page. 80 Infinite UKEK Retention. 80 Hear Clear . 81 The Global Positioning System (GPS) . 81 Understanding the GPS Feature . 81 Enhancing GPS Performance . 82 The Outdoor Location Feature (Using GPS) . 82 Accessing the Outdoor Location Feature . 83 Saving a Waypoint . 84 Viewing a Saved Waypoint . 85 Editing the Alias of a Waypoint . 86 Editing the Coordinates of a Waypoint . 86 Deleting a Single Saved Waypoint . 87 Deleting All Saved Waypoints . 88 Measuring the Distance and Bearing from a Saved Waypoint . 88 Using the Location Feature While in Emergency Mode 89 Trunking System Controls . 89 Using the Failsoft System . 89 Going Out-of-Range. 90 SmartZone. 90 Using Site Trunking Feature . 90 Locking and Unlocking a Site. 91 Viewing and Changing a Site . 91 Viewing the Current Site . 91 Changing the Current Site . 92 Trunked Announcement. 92 Initiating an Announcement . 93 Ignition Switch Options . 93 Blank . 93 Tx Inhibit. 93 PTT Tx Inhibit. 93 Required. 94 Soft Power Off . 94 Ignition Only Power Up . 94 Emergency Power Up . 94 Auto Power Off Timer. 95 Utilities . 95 Viewing Recent Calls List. 95 Selecting the Power Level . 96 C o n t e n t s Selecting a Radio Profile . 96 Controlling the Display Backlight . 97 Turning Keypad Tones On or Off . 97 Turning Voice Mute On or Off. 98 Using the Time-Out Timer . 98 Using the Conventional Squelch Operation Features99 Analog Options . 99 Digital Options . 99 Using the PL Defeat Feature . 100 Using the Digital PTT ID Feature . 100 Using the Smart PTT Feature (Conventional Only)100 Accessing General Radio Information . 101 Accessing Radio Information . 101 Viewing IP Information. 102 Viewing Control Assignments . 102 Using Siren, PA and Light . 103 Using Keypad as Siren Type Selector . 103 Using Keypad as Light Type Selector . 103 Using the Public Address Button on the Keypad . 103 Using the External Public Address Button on the Keypad. 104 Using Optional External Alarms (Horn and Lights) 104 Using Non-Permanent Horn and Lights. 104 Using Permanent Horn and Lights. 105 Changing the Selected Alarms . 105 Receiving a Call While Alarms are Turned On . 106 Turning Off Non-Rearmable External Alarms . 106 ix English Turning Off Rearmable External Alarms. 106 Using the Voice Announcement . 107 Helpful Tips . 108 Accessories . 109 Appendix: Maritime Radio Use in the VHF Frequency Range. 110 Special Channel Assignments. 110 Emergency Channel . 110 Non-Commercial Call Channel . 111 Operating Frequency Requirements . 111 Declaration of Compliance for the Use of Distress and Safety Frequencies . 113 Technical Parameters for Interfacing External Data Sources . 113 Glossary . 114 Commercial Warranty and Service . 118 s t n e t n o C x English Important Safety Information RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Stations ATTENTION!

This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Station which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. For a list of Motorola-approved antennas and other accessories, visit the following website:

http://www.motorolasolutions.com/APX Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power

(e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter has been approved by Industry Canada to operate with the Motorola-approved antenna types with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Note: Setting up the radio as an RF Modem takes complete control of the radio. In this mode, the radio no longer responds to button and PTT presses nor will it unmute to voice activity. This mode is designed to receive and pass specifically formatted over the air data to a tethered computer with RF modem enabled applications. This mode can only be exit by reprogramming the radio with Customer Programming Software (CPS) to not operate in RF modem mode and cycling power. I m p o r t a n t S a f e t y I n f o r m a t i o n ix English Software Version All the features described in the following sections are supported by the radio's software version R08.05.00 or later. Accessing Radio Information on page 101 to determine your radio's software version. Check with your dealer or system administrator for more details of all the features supported. Notice to Users (FCC and Industry Canada) This device complies with Part 15 of the FCC rules, Industry Canada license-exempt RSS standard(s) and RSS 210 of the Industry Canada rules per the conditions listed below:

1 This device may not cause harmful interference. 2 This device must accept any interference received, including interference that may cause undesired operation. 3 Changes or modifications made to this device, not expressly approved by Motorola, could void the user's authority to operate this equipment. i n o s r e V e r a w t f o S x English Informations importantes sur la scurit Guide sur lexposition aux radiofrquences et la scurit du produit pour radios mobiles bidirectionnelles

!

Mise en garde Avant d'utiliser ce produit, lisez les directives d'utilisation scuritaire prsentes dans le livret Scurit du produit et exposition l'nergie RF accompagnant votre radio. ATTENTION!

Cette radio est rserve un usage professionnel seulement pour satisfaire les normes d'exposition l'nergie RF de la FCC. Avant d'utiliser ce produit, lisez le guide inclus avec votre radio, qui contient d'importantes informations sur le mode d'emploi scuritaire du produit ainsi que des informations relatives l'nergie de RF et son contrle, afin d'assurer la conformit aux normes et rglements applicables. Pour obtenir une liste d'antennes et d'autres accessoires approuvs par Motorola, consultez le site Web :

http://www.motorolasolutions.com/APX Selon la rglementation d'Industrie Canada, cet metteur radio ne peut tre utilis qu'avec une antenne dont le type et le gain maximal (ou minimal) sont approuvs par Industrie Canada pour cet metteur. Afin de limiter les interfrences radio pour les autres utilisateurs, le type et le gain de l'antenne doivent tre choisis de faon ce que la puissance isotrope rayonne quivalente (P.I.R.E.) ne soit pas plus forte qu'il ne le faut pour tablir la communication. Le prsent metteur a t approuv par Industrie Canada pour fonctionner avec les types d'antenne agrs par Motorola et ayant un gain admissible maximal ainsi que l'impdance requise pour chaque type d'antenne indiqu. Les types d'antenne non inclus, dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour l'exploitation de l'metteur. Remarque: Rgler la radio en tant que modem RF prend le contrle complet de la radio. Dans ce mode, la radio ne rpond plus aux pressions des boutons de commande et PTT, et ne reoit aucun signal vocal. Ce mode est conu pour recevoir et transmettre des donnes spcifiquement formates pour la liaison radio avec un ordinateur attach dot d'applications compatibles avec le modem RF. Ce mode ne peut tre dsactiv qu'en reprogrammant la radio avec un logiciel CPS (programmation client) afin qu'elle ne fonctionne plus en mode modem RF et en la redmarrant. Version du logiciel Toutes les fonctionnalits dcrites dans les sections suivantes sont prises en charge par la version du logiciel R08.05.00 ou ultrieure de la radio. Vrifiez auprs de votre dtaillant ou de l'administrateur de systme pour obtenir des renseignements sur les fonctionnalits prises en charge. Avis aux utilisateurs (FCC et Industrie Canada) Cet appareil est conforme la Partie 15 des rglements de la FCC, normes CNR (cahiers des charges sur les normes radiolectriques) pour les appareils exempts de licence dIndustrie Canada et RSS 210 du rglement d'Industrie Canada selon les conditions numres ci-

dessous:

1 Ce dispositif ne doit pas causer d'interfrences nuisibles. 2 Cet appareil doit accepter toute interfrence reue, y compris les interfrences qui peuvent perturber le fonctionnement. i V e r s o n d u l o g c i i e l xi English 3 Les changements ou les modifications apportes ce dispositif, non expressment approuves par Motorola, peuvent annuler le droit de l'utilisateur utiliser cet quipement. Computer Software Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. s t h g i r y p o C e r a w t f o S r e t u p m o C xii English Documentation Copyrights No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others. Getting Started Take a moment to review the following:

How to Use This User Guide. page 1 Notations Used in This Manual . page 1 Additional Performance Enhancement . page 2 What Your Dealer/System Administrator Can Tell You . page 3 How to Use This User Guide This User Guide covers the basic operation of the APX Mobile Radios. However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information. Notations Used in This Manual Throughout the text in this publication, you will notice the use of WARNING, Caution, and Note. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed.The following special notations identify certain items:

!

!

W A R N I N G An operational procedure, practice, or condition, etc., which may result in injury or death if not carefully observed. G e t t i n g S t a r t e d

!

+ = K J E  

An operational procedure, practice, or condition, etc., which may result in damage to the equipment if not carefully observed. Note:

An operational procedure, practice, or condition, etc., which is essential to emphasize. 1 English Example Home button or H PHONE

>

Description Buttons and keys are shown in bold print or as an icon. Menu entries are shown similar to the way they appear on the radios display. This means Press the right side of the 4-way Navigation button. (Using keypad mic) Additional Performance Enhancement The following are some of the latest creations designed to enhance the security, quality and efficiency of APX mobile radios. Dynamic System Resilience (DSR) DSR ensures the radio system is seamlessly switched to a backup master site dynamically in case of system failure. DSR also provides additional indication e.g. failure detection, fault recovery, and redundancy within the system to address to the user in need. Mechanisms related to the Integrated Voice and Data (IV & D) or data centric are all supported by DSR. d e t r a t S g n i t t e G 2 English CrossTalk Prevention This feature prevents crosstalk scenario from happening, especially when a wideband antenna is used. This feature allows the adjustment of the Trident Transmitting SSI clock rate in the radio to be varied from the Receiving Frequency. This subsequently reduced the possibilities of radio frequency interfering spurs and prevents the issues of crosstalk. Encrypted Integrated Data (EID) EID provides security encryption and authentication of IV & D data bearer service communication between the radio and the Customer Enterprise Network. SecureNet SecureNet allows user to perform secured communications on an Analog or Motorola Data Communication (MDC) channel. The MDC OTAR feature will allow users to perform OTAR activities on an MDC channel. P25 Digital Vehicular Repeater System (DVRS) Motorola Solutions offers an MSI Certified APX compatible, 3rd Party, P25 Digital Vehicular Repeater System (DVRS) that provides low cost portable radio coverage in areas where only mobile radio coverage is available and portable radio coverage is either intermittent or non-existent. What Your Dealer/System Administrator Can Tell You You can consult your dealer or system administrator about the following:

Is your radio preprogrammed with any preset conventional channels?

Which buttons have been programmed to access other features?

What optional accessories may suit your needs?

Preparing Your Radio for Use Turning On the Radio. page 4 Validating Compatibility During Power Up. page 4 Adjusting the Volume . page 5 P r e p a r i n g Y o u r R a d o f o r U s e i 3 English Turning On the Radio Power Button Press the Power Button briefly turn on the radio. After a short time, the red, yellow and green LEDs light up. The display then shows Zone and channel text, and menu items display on the screen. The backlight will turn on to the last selected dim level. Note: Pressing the Power Button before the LED lights up LEDs will be ignored. If Fail ##/## appears in the display, the radio will not function until the condition has been corrected. If Error ##/## appears, some non-critical data has been changed. If either of these displays appear, if the display goes blank, or if the unit appears to be locked up, see Helpful Tips on page 108 for more information. If the power-up test is unsuccessful, you see Error XX/YY (XX/YY is an alphanumeric code). Turn off the radio, check the battery, and turn the radio back on. If the radio fails the power-up test again, i e s U r o f o d a R r u o Y g n i r a p e r P 4 English record the Error XX/YY code and contact your dealer. If CH Mismatch appears, means that either the Control Head has been connected to an incompatible transceiver, or vice versa. If your radio does not power up, contact your dealer. To turn off the radio, press the Power Button after the LEDs light up. Validating Compatibility During Power Up The radio validates and updates the software and hardware of your control head(s) during power up. Follow the procedure below when your radio runs this task. Procedure:

1 The display shows Maintenance mode remote device;

promptly followed by other maintenance statuses. 2 The display shows Update done please reset upon completion. OR The display shows Update failed please reset when it fails to update. 3 Press the Power Button to reset. The radio runs the usual power up operation if the software updates are complete. OR The radio runs the Maintenance Mode if the updates are not complete and repeat step 1. Note:

If Sw incomplete appears, use Flashport Recovery Tool to update the control heads before you power on the radio again. Adjusting the Volume To increase the volume, rotate the Multi-Function Knob (MFK) clockwise. To decrease the volume, rotate the MFK counterclockwise. The display shows volume bars and volume level when you change the volume. Multi-Function Knob Identifying Radio Controls Take a moment to review the following:

Radio Parts and Controls . page 6 O2 Control Head and Microphone . page 6 Programmable Features . page 7 Assignable Radio Functions . page 7 Assignable Settings or Utility Functions . page 9 Accessing the Preprogrammed Functions . page 10 Using the Menu Select Buttons . page 10 Using the Advance Programmable Buttons . page 11 Using the Navigation Buttons . page 11 Using the Keypad. page 14 Keypad Characters Uppercase Mode . page 14 Keypad Characters Lowercase Mode . page 15 Keypad Characters Numeric Mode . page 16 Keypad Characters Hexadecimal Mode . page 17 Push-To-Talk (PTT) Button. page 18 I i d e n t i f y n g R a d o C o n t r o s i l 5 English Radio Parts and Controls O2 Control Head and Microphone LED Indicators Bluetooth Indicator**

Emergency Button*

Push-to-Talk

(PTT) Button Power Button Up & Down Buttons*

Accy No-Dot Button (Purple)*

Data Feature Button*

Home Button

(Microphone) Keypad Navigation Button

(Microphone) Cancel Button

() Okay/Select Button ()

*This button is programmable. Note:

The microphone is not part of a radio. It is an optional accessory. l i s o r t n o C o d a R g n y f i t n e d i I 6 English Multi-function Knob

(MFK)*

Home Button Dimmer Button Menu Select Buttons*

Accessory Port (Microphone)

*These controls/buttons are programmable.

** Your radios hardware is Bluetooth ready. Check with your dealer or system administrator for more details of all the features supported Accy 1-Dot Button*

Accy 2-Dot Button*

Programmable Features Any reference in this manual to a control that is preprogrammed means that the control must be programmed by a dealer or a qualified radio technician using the radios programming software, in order to assign a feature to that control. The programmable buttons can be programmed as shortcuts to radio functions or preset channels/groups depending on the duration of a button press:

Press Pressing and releasing rapidly. Long press Pressing and holding for the programmed duration (between 0.25 seconds and 3.75 seconds). Hold down Keeping the button pressed. One Touch Button Each of the four Menu Select buttons, the Emergency button and the three Accy buttons on the microphone are programmable buttons which can be preprogrammed by a qualified radio technician to a default function which is activated upon a short press. Assignable Radio Functions Auxiliary Switches back and forth between two radios that are attached to the same control head. Call Alert Allows the radio to function like a pager, or to verify if a radio is active on the system. Call Response Allows you to answer a private call or phone call. Channel Selects a channel. Contacts Selects the Contacts menu. Delete Deletes digit, or deletes a nuisance channel in Scan. Digital Vehicle Repeater System Toggles between the Digital Vehicle Repeater System (VRS) mode. Dynamic Priority (Conventional Only) Allows any channel in a scan list (except for the Priority-One channel) to temporarily replace the Priority-Two channel. Emergency Depending on the programming, initiates or cancels an emergency alarm or call. Information Displays the basic radio information, IP-related information, and buttons or switches control mapping. Intercom Enables users of multiple control heads to talk to each other via the control heads in a multi-control head setup. Internet Protocol Address Displays the Internet Protocol (IP) address, device name, and status of the radio. Location Determines the current location (latitude, longitude, time and date), and also the distance and bearing to another I i d e n t i f y n g R a d o C o n t r o s i l 7 English location. Or, turns the GPS functionality on or off for all locations. Message Enters the current message list. Monitor (Conventional Only) Monitors a selected channel for all radio traffic until function is disabled. Multiple Private Line (Conventional Only) Selects the Multiple Private Line lists. Nuisance Delete Temporarily removes an unwanted channel, except for priority channels or the designated transmit channel, from the scan list. The designated transmit channel refers to the users selected zone/channel combination from which scan is initiated. One Touch 1 4 Launches a specific feature with one single button-press. You can setup as much as four separately programmed buttons for four different features. Phone Allows you to make and receive calls similar to standard phone calls. Private Line Defeat (Conventional Only) Overrides any coded squelch (DPL or PL) that is preprogrammed to a channel. Private Call (Trunking Only) Allows a call from an individual radio to another individual radio. Radio Profiles Allows for easy access to a set of preprogrammed visual and audio settings of the radio. l i s o r t n o C o d a R g n y f i t n e d i I 8 English Ext PA On/Off Toggles the audio routing between the connected public address (PA) loudspeaker amplifier and the radios internal public address (PA) system. Recent Calls Allows for easy access to the list of calls recently received or made. Rekey Request Notifies the dispatcher that you require a new encryption key. Repeater Access Button (RAB) (Conventional Only) Allows to manually send a repeater access codeword. Reprogram Request (Trunking Only) Notifies the dispatcher that you want a new dynamic regrouping assignment. Request-To-Talk (Conventional Only) Notifies the dispatcher that you want to send a voice call. Scan Toggles scan on or off. Scan List Programming Selects the scan list for editing. Secure/Clear Toggles secure transmission on or off. Select Selects the assigned list for editing. Selective Call (Conventional Only) Calls an assigned radio. Site Display (Trunking Only) Views the current site or enable a site search for SmartZone operation. Site Lock/Unlock (Trunking Only) Toggles between lock and unlock mode when using the SmartZone option. Site Search (Trunking Only) Performs site search for AMSS

(Automatic Multiple Site Select) or SmartZone operation. Status Sends data calls to the dispatcher about a predefined status. Talkaround/Direct (Conventional Only) Toggles between using a repeater and communicating directly with another radio. Talkgroup (Conventional Only) Allows a call from an individual radio to a group of radios. Text Messaging Service (TMS) Selects the text messaging menu. TMS Quick Text Selects a predefined message. User Login Automatically registers with the server. Zone Down Toggles downward through the zones in the radio. Zone Select Allows selection from a list of zones. Zone Up Toggles upward through the zones in the radio. Assignable Settings or Utility Functions Air Horn Toggles the external airhorn alert tone on or off. All Tones/Alerts Toggles all tones on or off. Dimmer Changes the display brightness. External Radio Toggles external radio on or off. Front/Rear Switches one of two control heads to be active at one time. HiLo Toggles the Hilo Airhorn tones on or off. Backlight Toggles display backlight on or off. Horns/Lights Toggles horns and lights feature on or off. Keypad Mute Toggles the keypad tones on or off. Keypad Lock Locks the radios keypad, or even locks in the radios currently operating channel when the Mode Knob scrolls to other channels. Low Power Toggles transmit power level between high and low. Manual Toggles the manual tone on or off. Public Address On/Off Toggles the radios internal public address (PA) system on or off. Siren Toggles external siren alert tone on or off. I i d e n t i f y n g R a d o C o n t r o s i l 9 English Squelch Toggles squelch level between normal open and tight. TX Power Level Toggles transmit power level between high and low. Voice Announcement Audibly indicates the current feature mode, Zone or Channel the user has just assigned. Voice Mute Toggles voice mute on or off for the channels which have enabled In-Call User Alert. When Voice Mute is active, the radio remains muted to all conventional dispatch calls and affiliated trunking group calls. Volume Set Tone Adjusts the volume of the speakers, or adjusts the volume of the radios alert tones. Wail Toggles the external wail alert tone on or off. Yelp Toggles the external yelp alert tone on or off. Accessing the Preprogrammed Functions You can access various radio functions through one of the following ways:

A short or long press of the relevant programmable buttons. OR Use the Menu Select Button (g). Using the Menu Select Buttons The Menu Select Buttons allow you to access the menu entries of features. Note: Check with your dealer or system administrator for the list of features activated in your radio. Your radio may be preprogrammed differently from the following example, but the steps for selecting a zone may appear as shown below:

Press the Menu Select button (g) directly below Zone. l i s o r t n o C o d a R g n y f i t n e d i I 10 English Using the Advance Programmable Buttons This feature is to help you to shorten the process of applying certain common features. Up & Down Buttons Emergency Button*

Menu Select Buttons*

Accy No-Dot Button

(Purple)*

Accy 1-Dot Button*

Accy 2-Dot Button*

* These programmable buttons support the One Touch Button feature.

(Quick Access) One Touch Button Enters a menu with a short press on the preprogrammed One Touch button. Features assigned to these buttons are Call, Call Alert, Phone, Repeater Access, MDC RTT Button Access, Status and Message. Using the Navigation Buttons Your radio is equipped with navigation buttons. The navigation buttons will allow you to access the features in the radio. Up and Down Buttons By default, the U and D buttons are used as up and down arrow input. These buttons are programmable. They can be programmed to navigate through zones, channels and to increase and decrease the volume of the radio. Right and Left Buttons The > and < buttons mentioned throughout the manual can be found on the keypad microphone (keypad mic.). These buttons will allow you to navigate the lists in the radio. I i d e n t i f y n g R a d o C o n t r o s i l 11 English Home Button Multi-function Knob The H button returns you to the home (default) display. In most cases, this is the current mode. The MFK button on your radio is programmable to the following features :

For selected radio features, the H button is also used to save user-edited radio settings or information before returning you to the Home screen. Note: Some features do not require you to press H to go to the Home screen. Refer to the individual feature sections in this manual for further details on saving user-edited radio settings or information. The H button also can revert to home channel from any other zone and mode in the radio. Check with your dealer or system administrator for more information. Dimmer Button Use this button to adjust the brightness of the display. Long press to toggle between day and night mode. l i s o r t n o C o d a R g n y f i t n e d i I 12 English Mode Change to scroll the channel list.

- Press the MFK once and turn clockwise

-Turn the MFK clockwise or Volume Change counterclockwise to adjust the volume level of the speaker. The volume level can be adjusted in 16 steps or 32 steps. A fast turn of the MFK adjusts the volume level in 16 steps with large increments in volume level. A slow turn of the MFK adjusts the volume level in 32 steps with small increments in volume level. The display shows the volume level and bars to indicate the current level. The level of last selected volume when your radio powers down remains the same when the radio powers up. The main display shows the icon of the secondary feature.The main display does not show the icon of primary feature. Your radio by default is set to use the primary feature. Short press the MFK to toggle it to work on either the secondary or primary feature. The concentric ring LED on the MFK will blink in green when the knob is set to secondary feature. The secondary feature has an inactivity timer. This timer starts when the secondary feature is idle. The radio returns to primary feature when the timer expires. If the MFK is set to operate only one feature, it is recommended that it be set to Volume Change. Consult your dealer or system administrator for the best option available for MFK. Concentric Ring LED I i d e n t i f y n g R a d o C o n t r o s i l 13 English Using the Keypad You can use the 3 x 4 alphanumeric keypad on the keypad microphone to access your radios features. The keypad functions in a manner similar to a standard telephone keypad when entering numeric digits. When the keypad is used to edit a list, each key can generate different characters of the alphabet. The tables below show the number of times a key needs to be pressed to generate the required character. Keypad Characters Uppercase Mode 14

/

15

+

16

=

17

\

18 19 20

(

21

) l i s o r t n o C o d a R g n y f i t n e d i I 7 5

!

9

-

4

?

Number of Times Key is Pressed 6 8

; @ _ 10

*

12

&

11

#

13

$

3

, C F I L O R V Y 2 Key 1 1 1

. 2 A B 3 D E 4 G H 5 J K 6 M N 7 P Q 8 T U 9 W X 0 Toggle between mixed case mode, uppercase mode, and lowercase mode.

* Space

# Toggle between numeric and letter mode. S Z 14 English Keypad Characters Lowercase Mode 14

/

7 5

!

9

-

4

?

Number of Times Key is Pressed 8 6

; @ _ 10

*

12

&

11

#

13

$

3

, c f i l o r v y 2

. b e h k n q u x 1 Key 1 1 2 a 3 d 4 g 5 j 6 m 7 p 8 t 9 w 0 Toggle between mixed case mode, uppercase mode, and lowercase mode.

* Space

# Toggle between numeric and letter mode. s z 15

+

16

=

17

\

18 19 20

(

21

) I i d e n t i f y n g R a d o C o n t r o s i l 15 English 15

+

16

=

17

\

18 19 20

(

21

) Keypad Characters Numeric Mode Number of Times Key is Pressed 8 6

; @ _ 10

*

13

$

12

&

11

#

9

-

7 14

/

5

!

3

, 2

. 4

?

1 Key 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 0 0

* Space

# Toggle between numeric and letter mode. l i s o r t n o C o d a R g n y f i t n e d i I 16 English Keypad Characters Hexadecimal Mode 3 2 B E A D 1 Key 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 0 0

* Not applicable

# Not applicable Number of Times Key is Pressed 8 10 13 12 11 9 14 5 6 7 4 C F 15 16 17 18 19 20 21 I i d e n t i f y n g R a d o C o n t r o s i l 17 English Push-To-Talk (PTT) Button PTT Button The PTT button on the side of the microphone serves two basic purposes:

While a call is in progress, the PTT button allows the radio to transmit to other radios in the call. Press and hold down PTT button to talk. Release the PTT button to listen. The microphone is activated when the PTT button is pressed. While a call is not in progress, the PTT button is used to make a new call. See Making a Radio Call on page 35 for more information. Identifying Status Indicators Your radio indicates its operational status through the following:

Status Icons . page 19 Text Messaging Service (TMS) Icons . page 21 Status Icons . page 21 TMS Menu Options . page 22 LED Indicator . page 24 Intelligent Lighting Indicators . page 25 Alert Tones. page 26 s r o t a c d n i I s u t a t S g n y f i t n e d i I 18 English Status Icons The liquid crystal display (LCD) of your radio shows the radio status, text entries, and menu entries. The following are the icons that appear on the radios display. u t F V N Receiving Radio is receiving a call or data. Transmitting Radio is transmitting a call or data. Call Received Radio has received an Individual Call. Received Signal Strength Indicator (RSSI) The number of bars displayed represents the received signal strength for the current site, for trunking only. The more stripes in the icon, the stronger the signal. Direct On = Radio is currently configured for direct radio-to-radio communication (during conventional operation only). Off = Radio is connected with other radios through a repeater. M K Monitor (Carrier Squelch) Selected channel is being monitored (during conventional operation only). In-Call User Alert On = The feature is enabled. Voice muting of the affiliated trunking talkgroup or selected channel is activated. Off = The feature is disabled. Voice muting of the affiliated trunking talkgroup or selected channel is deactivated. H or . i j Power Level L = Radio is set at Low power. H = Radio is set at High power. Scan Radio is scanning a scan list. Priority Channel Scan Blinking dot = Radio detects activity on channel designated as Priority-One. Steady dot = Radio detects activity on channel designated as Priority-Two. I i d e n t i f y n g S t a t u s I i n d c a t o r s 19 English k m l G Vote Scan Enabled The vote scan feature is enabled. Secure Operation On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. AES Secure Operation On = AES Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. Location Signal On = Location feature is enabled, and location signal is available. Off = Location feature is disabled. Blinking = Location feature is enabled, but no location signal is available. n o

{

User Login Indicator (IP Packet Data) Inverted = User is currently associated with the radio. On = Packet data context activated. Off = Packet data context deactivated. Blinking = Device registration or user registration with the server failed due to an invalid username or pin. Data Activity Data activity is present. Hexadecimal Indicates that the text entry is currently in hexadecimal mode. MFK is in Mode Change feature Turn the MFK to change channel. MFK is in Volume Change feature Turn the MFK to adjust the volume. s r o t a c d n i I s u t a t S g n y f i t n e d i I 20 English Text Messaging Service (TMS) Icons This feature allows you to send and receive text messages. See Text Messaging Service (TMS) on page 66 for more information. Status Icons Inbox Full The Inbox is full. The following icons appear on the radios display for TMS features:

,

[

Z r Message Sent The text message is sent successfully. Message Unsent The text message cannot be sent. Unread Message User receives a new message. The selected text message in the Inbox has not been read.

]

3/6 I P

;

p Read Message The selected text message in the Inbox has been read. Message Index Indicates the index of the current message the user is viewing. Example: If the user is looking at the third message out of a total of 6 messages in the Inbox folder, the icon is displayed as the icon on the left column. Priority Status The Priority feature is toggled on before the message is sent. Messages in the Inbox folder are flagged with Priority. Request Reply The Request Reply feature is toggled on before the message is sent. Messages in the Inbox folder are flagged with Request Reply. I i d e n t i f y n g S t a t u s I i n d c a t o r s 21 English q 2 1 3

}

Priority Status and Request Reply User is composing a message with a priority status and a request for a reply. Messages in the Inbox folder are flagged with Priority and Request Reply. Numeric Indicates that the text entry is currently in numeric mode. Mixed Case Indicates that the text entry is currently in normal text mode. Uppercase Indicates that the text entry is currently in uppercase mode. Lowercase Indicates that the text entry is currently in lowercase mode. Lowercase Indicates that the text entry is currently in lowercase and with predicted words shown at the bottom of the screen. s r o t a c d n i I s u t a t S g n y f i t n e d i I 22 English Mixedcase Predictive Indicates that the text entry is currently in mixed case and with predicted words shown at the bottom of the screen. Uppercase Predictive Indicates that the text entry is currently in uppercase and with predicted words shown at the bottom of the screen. TMS Menu Options Menu Option Description/Function Back Edit Save Rply Del New Impt Brings you back to the previous menu screen. Edits a draft message or key in a target address. Saves the messages you have edited to the Draft folder. Replies to a message. Deletes a message or a character text during editing mode. Creates a new message. Toggles the Priority Status icon on or off for an outgoing message.

?

%

Menu Option Description/Function Rqrp Yes No Exit Optn Sel Send Toggles Request Reply icon on or off for an outgoing message. Deletes all the messages in the current folder. Cancel the delete all messages options. Exits to the Home screen. Brings you to the Options main screen. Selects a predefined message or address. Sends the message. Call Type Icons The following icons appear on the radios main display, when you make or receive a call, or view selected call lists, to indicate the different call types associated with an alias or ID. U Radio number. Radio number added to a Call List. Mobile number. I Mobile number added to a Call List. Landline phone number. Landline phone number added to a Call List. Incoming call or data. Outgoing call or data. i d e n t i f y n g S t a t u s I i n d c a t o r s 23 English Multi-function Knob - Concentric Ring LED The concentric ring LED blinks green when the MFK is using the secondary feature. See Multi-function Knob on page 12 to understand the functionality of MFK. If Intelligent Lighting is activated, the concentric ring LED will not blink green when the MFK is in the secondary mode. The LED turns into solid color of orange, red or green depending on the status of Intelligent Lighting. See Intelligent Lighting Indicators on page 25 for different status of Intelligent Lighting. Concentric Ring LED LED Indicator LED indicator shows the operational status of your radio. Red LED Yellow LED Green LED s r o t a c d n i I s u t a t S g n y f i t n e d i I Solid red Radio is transmitting. Blinking red Radio is transmitting at low power condition. Double blinking red Radio is in Emergency Mode. Rapidly blinking red Radio has failed the self test upon powering up or encountered a fatal error. Solid yellow Channel is busy. Blinking yellow Radio is receiving a secured transmission. Solid green Radio is powering up, or is on a non-priority channel while in the Scan List Programming mode. Blinking green Radio is receiving an individual or telephone call, or is on a Priority-Two channel while in the Scan List Programming mode. Rapidly blinking green Radio is on a Priority-One channel while in the Scan List Programming mode. 24 English Intelligent Lighting Indicators This feature temporarily changes the radios display backlight color and the alert text background color to help signal that a radio event has occurred. Note:

This feature must be preprogrammed by a qualified radio technician. Backlight Orange Event Emergency Alerts Red Critical Alerts Green Call Alerts When The radio initiates an emergency alarm or call. The radio receives an emergency alarm or call. The radio is out of range. The radio enters failsoft mode. The radio is unable to establish a full connection with the system. The radio is unable to authenticate or register with the system. The radio receives a private call. The radio receives a phone call. The radio receives a call alert. The radio receives a selective call. I i d e n t i f y n g S t a t u s I i n d c a t o r s 25 English Alert Tones An alert tone is a sound or group of sounds. Your radio uses alert tones to inform you of your radios conditions. The following table lists these tones and when they occur. You Hear Tone Name Heard Short, Low-Pitched Tone Long, Low-Pitched Tone Radio Self Test Fail Reject Time-Out Timer Warning No ACK Received Individual Call Warning Tone Time-Out Timer Timed Out When radio fails its power-up self test. When an unauthorized request is made. Four seconds before time out. When radio fails to receive an acknowledgment. When radio is in an individual call for greater than 6 seconds without any activity. When the Time-Out Timer has expired. Talk Prohibit/PTT Inhibit Out of Range Invalid Mode

(When PTT button is pressed) transmissions are not allowed.

(When PTT button is pressed) the radio is out of range of the system. When radio is on an unpreprogrammed channel. A Group of Low-Pitched Tones Busy When system is busy. s r o t a c d n i I s u t a t S g n y f i t n e d i I 26 English You Hear Medium-Pitched Short, Tone Medium-Pitched Long, Tone Tone Name Valid Key-Press Radio Self Test Pass Clear Voice Priority Channel Received Heard When correct key is pressed. When radio passes its power-up self test. At beginning of a non-coded communication. When activity on a priority channel is received. Emergency Alarm Entry When entering the emergency state. Central Echo Volume Set When central controller has received a request from a radio. When volume is changed on a quiet channel. Emergency Exit When exiting the emergency state. A Group of Medium-Pitched Tones Failsoft Automatic Call Back Talk Permit Keyfail When the trunking system fails. When voice channel is available from previous request.

(When PTT button is pressed) verifying system accepting transmissions. When encryption key has been lost. When status, emergency alarm, or reprogram request ACK is received. Console Acknowledge Received Individual Call When Call Alert or Private Call is received. Call Alert Sent Site Trunking When Call Alert is received by the target radio. When a SmartZone trunking system fails. I i d e n t i f y n g S t a t u s I i n d c a t o r s 27 English You Hear Ringing Low-Pitched Gurgle Unique, Chirp Unique, High-Pitched Chirp Tone Name Fast Ringing Enhanced Call Sent Phone Call Received Dynamic Regrouping Heard When system is searching for target of Private Call. When waiting for target of Private Call to answer the call. When a land-to-mobile phone call is received.

(When the PTT button is pressed) a dynamic ID has been received. New Message When a new message is received. Priority Status When a priority message is received. s r o t a c d n i I s u t a t S g n y f i t n e d i I 28 English You Hear Tone Name When Two high-pitched tones Four high-pitched tones every five seconds Single, high-pitched tone Private Conversation When a Private Call is received. Call Alert When a Call Alert page is received. Central Acknowledge When a Call Alert, emergency alarm, reprogram request, or status/message transmission is received by the systems central controller. Four high-pitched tones Mobile Unit Acknowledge When a Call Alert page is received by the intended unit, or the emergency System Busy alarm, reprogram request, or status/message transmission is acknowledged by the intended dispatcher. When the PTT button is pressed, indicates transmission fail because all system radio channels are in use. Release the PTT button and wait for call back. Automatic Call Back When a channel is now available for your previously requested transmission. Talk Permit (Optional) When the PTT button is pressed, indicates the system is accepting your Scan Alert On transmission. When Scan feature is activated through the preprogrammed button. I i d e n t i f y n g S t a t u s I i n d c a t o r s Sound similar to a telephone busy signal A series of two short, high-pitched tones A series of low-pitched tones followed by a series of high-pitched tones A series of high-pitched tones followed by a series of low-pitched tones Scan Alert Off When Scan feature is deactivated through the preprogrammed button. 29 English You Hear Continuous, low-pitched tone Tone Name Talk-Prohibit Smart PTT Inhibit When

(When the PTT button is pressed) the system is out of service.

(When the PTT button is pressed) the channel is busy with the Smart PTT feature enabled.

(When the PTT button is pressed) indicates the radio is not in the range of the trunked radio system. When you have entered a mode where normal system traffic will be missed, or you are attempting something which is not permitted. Examples include: forgetting to exit the telephone interconnect mode after a call ends (fleet and subfleet calls cannot be received), attempting to transmit on a receive-only conventional mode, attempting to select a dynamic mode where no dynamic ID assignment has been made. Powers off the radio when no user actions occur during a preprogrammed length of time. When a trunked system central controller failure in an unmuted receive condition. The radio reverts from trunked operation to a system similar to conventional radio repeater operation. Other system users can be heard sharing the channel. When your present transmission will soon be disabled. Out-of-Range Illegal Mode Auto Power Off Failsoft Time-Out Timer Warning or Menu Inactive Exit Valid Key Invalid Key When you pressed a valid key, or you entered a feature configuration state, or you are receiving or transmitting in the clear mode on secure models (with TX Clear Alert Tones enabled). When you tried to make an invalid key press, or that an emergency alarm, reprogram request, or status/message was not acknowledged. s r o t a c d n i I s u t a t S g n y f i t n e d i Single, high-pitched tone every nine seconds Brief low-pitched tone Single, short, high-pitched tone I Single, low-pitched tone 30 English General Radio Operation Once you understand how your APX Mobile Radio is configured, you are ready to use your radio. Use this navigation guide to familiarize yourself with the basic Call features:

Selecting a Zone . page 31 Selecting a Radio Channel . page 32 Receiving and Responding to a Radio Call. page 32 Making a Radio Call . page 35 Repeater or Direct Operation . page 37 Monitoring Features. page 38 Selecting a Zone A zone is a group of channels. Note: Your radio must be preprogrammed to allow you to use these features. Procedure:

If zone is set as the primary mode, 1 Turn the MFK until the display shows the desired zone and press the PTT button to begin transmitting on the displayed zone. If zone is not set as the primary mode, press the MFK once and repeat step 1. OR 2 > or < (on the keypad mic.) to Zone. 3 Press the Menu Select button directly below Zone. The display shows the current zone. 4 Rotate the MFK or press U or D to the desired zone is displayed. 5 Press the Menu Select button directly below Sel or the button (on the keypad mic.) to confirm the selected zone number. G e n e r a l i R a d o O p e r a t i o n 31 English 6 Press the PTT button to begin transmitting on the displayed zone. 6 Press the PTT button to transmit on the displayed channel. Selecting a Radio Channel A channel is a group of radio characteristics, such as transmit/

receive frequency pairs. Use the following procedure to select a channel. Procedure:

If channel is set as the primary mode, 1 Turn the MFK until the display shows the desired channel and press PTT to begin transmitting on the displayed. If channel is not set as the primary mode, press the MFK once and repeat step 1. OR 2 > or < (on the keypad mic.) to scroll to Chan. 3 Press the Menu Select button directly below Chan. The display shows the current channel. Receiving and Responding to a Radio Call Once you have selected the required channel and/or zone, you can proceed to receive and respond to calls. Red LED Yellow LED Green LED You will see solid red LED while the radio is transmitting. You will see solid yellow LED when the radio is receiving a transmission in conventional mode and there is no LED indication when the radio receives a transmission in trunking mode. If the radio is receiveing a secure transmission, the yellow LED blinks. 4 Rotate the MFK or press U or D to the desired channel. 5 Press the Menu Select button directly below Sel or the button (on the keypad mic.) to confirm the channel. n o i t a r e p O o d a R i l a r e n e G 32 English Receiving and Responding to a Talkgroup Call To receive a call from a group of users, your radio must be configured as part of that talkgroup. Procedure:

When you receive a talkgroup call (while on the Home screen), depending on how your radio is preprogrammed:

1 ASTRO Conventional Only:

The LED lights up solid yellow. The display shows the talkgroup alias or ID, and the caller alias or ID. OR Trunking Only:

The display shows the caller alias or ID. 2 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to respond to the call. The LED lights up solid red. 4 Release the PTT button to listen. See Making a Talkgroup Call on page 35 for details on making a Talkgroup Call. Receiving and Responding to a Private Call

(Trunking Only) A Private Call is a call from an individual radio to another individual radio. These one-to-one calls between two radios are not heard by others in the current talkgroup. The calling radio automatically verifies that the receiving radio is active on the system and can display the caller ID. Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure:

When you receive a Private Call:

1 You hear two alert tones and the LED blinks green. The display shows Call received and the caller alias or ID. 2 Press the Menu Select button directly below Resp within 20 seconds after the call indicators begin. 3 During the call, the display shows the caller alias (name), if it is in the call list. OR During the call, the display shows the caller ID (number), if the callers name is not in the call list. G e n e r a l i R a d o O p e r a t i o n 33 English Receiving and Responding to a Telephone Call This feature allows you to receive calls similar to standard phone calls from a landline phone. Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure:

1 You hear a telephone-type ringing and the LED blinks green. The backlight of the screen turns green. The display shows Phone call and the call received icon blinks. 2 Press the Menu Select button directly below Resp. 3 Press and hold the PTT button to talk. Release the PTT button to listen. 4 Press H or the Menu Select button directly below Exit to hang up and return to the Home screen. See Making a Telephone Call on page 37 for details. 4 Press and hold the PTT button to talk. Release the PTT button to listen. 5 Press H to hang up and return to the Home screen. Note:

If you press PTT button before pressing the Menu Select button directly below Resp, your conversation will be heard by all members of the talk group. If 20 seconds pass before you press the Menu Select button directly below the Resp, you will not respond privately to the call just received. Instead, you initiate a Private Call. See Making a Private Call (Trunking Only) on page 36 for details on making a Private Call. n o i t a r e p O o d a R i l a r e n e G 34 English Making a Radio Call You can select a zone, channel, subscriber ID, or talkgroup by using:

The preprogrammed Zone switchmenu The Multi-function Knob A preprogrammed One Touch button The Contacts list (see Contacts on page 45). Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Making a Talkgroup Call To make a call to a group of users, your radio must be configured as part of that talkgroup. Procedure:

1 > or < (on the keypad mic.) to Tgrp and press the Menu Select button directly below Tgrp. The display shows the last-selected talkgroup. 2 Press the Menu Select button directly below Sel. OR Rotate the MFK or U or D to select the channel with the desired talkgroup the press the Menu Select button directly below Sel. 3 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. G e n e r a l i R a d o O p e r a t i o n 4 Press the PTT button to make the call. 5 ASTRO Conventional Only:

The LED lights up solid red. The display shows the talkgroup alias or ID. OR Trunking Only:

The LED lights up solid red. 6 Speak clearly into the microphone. 7 Release the PTT button to listen. 35 English 6 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 7 When you are connected, the display shows the ID of the target radio. Press and hold the PTT button to talk. Release the PTT button to listen. OR If no acknowledgment is received, the display shows No acknowledge. OR If the target radio does not respond before the time out, the display shows No answer. 8 Press H to return to the Home screen. See Sending a Call Alert Page on page 55 for more information. Making a Private Call (Trunking Only) This feature allows you to send an individual Call Alert or page if there is no answer from the target radio. Your radio must be preprogrammed to allow you to use this feature. Procedure:

Press the preprogrammed Quick Access (One-Touch) Enhanced Private Call button to dial the preprogrammed ID and proceed to Step 5. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Call. 2 Press the Menu Select button directly below Call. The display shows the last transmitted or received. 3 Press the Menu Select button directly below Cnts to scroll through and select the required ID. OR D or U to the required ID. OR Use the keypad to enter the required ID. 4 Press the PTT button to start the Private Call. 5 A telephone-type ringing sounds if the receiving unit is in service. The display shows Calling...<Number> or Calling...<Alias>. n o i t a r e p O o d a R i l a r e n e G 36 English Making a Telephone Call This feature allows you to make calls similar to standard phone calls to a mobile or landline phone. Procedure:

Press the preprogrammed Quick Access (One-Touch) Phone Call button to dial the preprogrammed phone number and proceed to Step 5. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Phon. 2 Press the Menu Select button directly below Phon. The display shows the last transmitted phone number. 3 Press the Menu Select button directly below Cnts to scroll through and select the required ID. OR D or U to the required phone number. OR Use the keypad to enter the required phone number. 4 Press and release the PTT button to dial the phone number. 5 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 6 When your call is answered, press the PTT button to talk. 7 Release the PTT button to listen. 8 Press H to return to the Home screen. See Alert Tones on page 26 for more information if your call is NOT answered. Repeater or Direct Operation G e n e r a l i R a d o O p e r a t i o n The REPEATER operation increases the radios range by connecting with other radios through a repeater. The transmit and receive frequencies are different. The DIRECT or talkaround operation allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same. Procedure:

Press the preprogrammed Repeater/Direct switch to toggle between talkaround and repeater modes. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Dir. 2 Press the Menu Select button directly below Dir. 3 The display shows Repeater mode if the radio is currently in Repeater mode. OR The display shows Direct mode and the Talkaround icon if 37 English the radio is currently in Direct mode (during conventional operation only). You can repeat step 2 to toggle between the two modes. Once in Direct Mode, press PTT button to start conversation with the radios nearby. Monitoring Features Radio users who switch from analog to digital radios often assume that the lack of static on a digital channel is an indication that the radio is not working properly. This is not the case. Digital technology quiets the transmission by removing the noise from the signal and allowing only the clear voice or data information to be heard. Monitor a channel to ensure the channel is clear before transmitting. 2 Adjust the volume by rotating the MFK if necessary. 3 If you hear no activity, press and hold the PTT button to start your conversation. OR Trunked Modes Only:

1 Press the PTT button. 2 If you hear two, short, high-pitched tones, or if you hear no tone and the t indicator lights steadily, then proceed with your message. 3 Release the PTT button to receive (listen). If you are not in the range of the system, you may hear a continuous low-pitched tone and the display shows Out of range. n o i t a r e p O o d a R i l a r e n e G 38 English Monitoring a Channel Procedure:

Lift the microphone off hook. Conventional Modes Only:

1 Listen for activity on that channel. Conventional Mode Operation This feature allows you to monitor channel traffic on conventional channels by defeating the coded squelch. This way, you can listen to another user active on the channel. Thus, you may be prevented from talking over someone elses conversation. Note:

This feature must first be enabled by a qualified radio technician or system administrator. Procedure:

Take the control head off hook. (This is the same as monitor on. You hear all channel traffic.) OR 1 At Home mode where the default zone and channel are being displayed, > or < button (on the keypad mic.) to Mon. 2 Press the Menu Select button directly below Mon momentarily to activate monitoring. The display shows Monitor on. 3 Press the Menu Select button to deactivate the monitoring. The display shows Monitor off. G e n e r a l i R a d o O p e r a t i o n 39 English Advanced Features Use this navigation guide to learn more about advanced features available with your radio:

Advanced Call Features . page 40 Contacts . page 45 Scan Lists . page 51 Scan . page 53 Call Alert Paging . page 57 Emergency Operation . page 59 Automatic Registration Service (ARS) . page 63 Text Messaging Service (TMS) . page 66 Secure Operations . page 76 The Global Positioning System (GPS) . page 81 Trunking System Controls. page 89 Ignition Switch Options . page 93 Utilities. page 95 Advanced Call Features Calling a Phone Not in the List 1 > or < (on the keypad mic.) to Phon. 2 Press the Menu Select button directly below Phon. 3 Enter the desired phone number from the optional keypad microphone. The display updates as the numbers are entered. 4 Press button or the PTT button (on the keypad mic.) to make the call. 5 Press and hold the PTT button to talk. Release the PTT button to listen. 6 Press H or Menu Select button directly below Phon to exit. s e r u t a e F d e c n a v d A 40 English Receiving and Making a Selective Call

(Conventional Only) This feature allows you to receive a call from or to call a specific individual. It is intended to provide privacy and to eliminate the annoyance of having to listen to conversations that are of no interest to you. Receiving a Selective Call Procedure:

1 When you receive a Selective Call, you hear two alert tones and the LED lights up solid yellow. The call received icons blink and the display alternates between Call received and the home display. 2 The speaker unmutes. 3 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 4 Press and hold the PTT button to talk. Release the PTT button to listen. Note:

If you press PTT button before pressing the Menu Select button directly below Call, your conversation will be heard by all members of the talk group. A d v a n c e d F e a t u r e s If 20 seconds pass before you press the Menu Select button directly below the Call, you will not respond privately to the call just received. Instead, you initiate a Selective Call. See Making a Selective Call on page 41. Making a Selective Call Procedure:

Press the preprogrammed Quick Access (One-Touch) Selective Call button to dial the preprogrammed ID and proceed to Step 4. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Call. 2 Press the Menu Select button directly below Call. The display shows the last transmitted or received ID. 3 Press the Menu Select button directly below Cnts to scroll through and select the required ID. OR D or U to the required ID. OR Use the keypad to enter the required ID. 4 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 5 Press and hold the PTT button to start the Selective Call. The display shows the ID of the target radio. 41 English 6 Release the PTT button to listen. 7 Press H to return to the Home screen. Selecting a Talkgroup Procedure:

If you do not press H button to hang up, your radio will remain in Selective Call state with the other unit. You will miss all subfleet traffic and incoming phone calls. Using the Talkgroup Call Feature (Conventional Operation Only) This feature allows you to define a group of conventional system users so that they can share the use of a conventional channel. Note: Encryption keys are associated to talkgroups. When talkgroups are enabled, encryption keys are changed by changing the active talkgroup. See Secure Operations on page 76 for more information. s e r u t a e F d e c n a v d A 1 > or < (on the keypad mic.) to Tgrp. 2 Press the Menu Select button directly below Tgrp. The display shows the last talkgroup that was selected and stored. 3 U or D to Pset for the preset preprogrammed talkgroup. OR D or U to the required talkgroup. OR Use the keypad to enter the number of the corresponding talkgroup in the list. 4 Press the Menu Select button directly below Sel to save the currently selected talkgroup and return to the Home screen. 5 If the encryption key associated to the new talkgroup is erased, a momentary key fail tone sounds and the display shows Key fail. OR If the encryption key that is associated to the new talkgroup is not allowed, a momentary key fail tone sounds and the display shows Illegal key. 6 Press H or the PTT button to exit. 42 English Sending a Status Call This feature allows you to send data calls to the dispatcher about a predefined status. Each status can have up to a 14-character name. A maximum of eight status conditions is possible. Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure:

Press the preprogrammed Status button and proceed to Step 3. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Sts. 2 Press the Menu Select button directly below Sts. 3 The display shows the last acknowledged status call, or the first status in the list. 4 D or U to the required status. OR Use the keypad to enter a number corresponding to the location in the status list. 5 Press the PTT button to send the status. The display shows Please wait. 6 When the dispatcher acknowledges, four tones sound and the display shows Ack received. The radio returns to normal dispatch operation. OR If no acknowledgment is received, a low-pitched tone sounds and the display shows No acknowledge. 7 Press H to return to the Home screen. No traffic is heard on trunked channels while Status Calls is selected. If the radio detects no Status Call activity for six seconds, an alert tone sounds until you press H or the PTT button. A d v a n c e d F e a t u r e s 43 English Using the Dynamic Regrouping Feature (Trunking Only) This feature allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. This feature is typically used during special operations and is enabled by a qualified radio technician. You will not notice whether your radio has this feature enabled until a dynamic regrouping command is sent by the dispatcher. Note:

If you try to access a zone or channel that has been reserved by the dispatcher as a dynamically regrouped mode for other users, an invalid tone sounds. Procedure:

1 When your radio is dynamically regrouped, it automatically switches to the dynamically regrouped channel. A gurgle tone sounds and the display shows the dynamically regrouped channels name. 2 Press the PTT button to talk. Release PTT button to listen. When the dispatcher cancels dynamic regrouping, the radio automatically returns to the zone and channel that you were using before the radio was dynamically regrouped. Requesting a Reprogram This feature lets you notify the dispatcher that you want a new dynamic regrouping assignment. Procedure:

Press the preprogrammed Reprogram Request button to send reprogram request to the dispatcher and proceed to Step 3. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Rpgm. 2 Press the Menu Select button directly below Rpgm to send reprogram request to the dispatcher. 3 The display shows Reprogram rqst and Please wait. 4 If you hear five beeps, the dispatcher has acknowledged the reprogram request. The display shows Ack received and the radio returns to the Home screen. OR If the dispatcher does not acknowledge the reprogram request within six seconds, a low-pitched alert tone sounds and the display shows No acknowledge. Try again or press H to cancel and return to the Home screen. s e r u t a e F d e c n a v d A 44 English Classifying Regrouped Radios The dispatcher can classify regrouped radios into either of two categories: Select Enabled or Select Disabled. Select-enabled radios are free to change to any available channel, including the dynamic-regrouping channel, once the user has selected the dynamic-regrouping position. Select-disabled radios cannot change channels while dynamically regrouped. The dispatcher has forced the radio to remain on the dynamic-regrouping channel. The Scan or Private Call feature cannot be selected while your radio is Select Disabled. A d v a n c e d F e a t u r e s Contacts This feature provides address-book capabilities on your radio. Each entry corresponds to an alias (name) or ID (number) that you use to initiate a call. Contact entries are alphabetically sorted according to entry alias. Each alias can have up to 5 IDs of different call types associated with it. Additionally, each entry, depending on context (conventional, trunking, or phone), associates with one or more of the four types of calls: Phone Call, Selective Call, Private Call, or Call Alert. Each entry within Contacts displays the following information:

Call Alias (Name) Call ID (Number) Call Type (Icon) WACN ID (Astro 25 Trunking IDs only) System ID Note: Your radio must be preprogrammed to allow you to add, edit, or delete the contact entries. Your radio also supports a maximum of 50 call lists. Each list can store up to 100 IDs (numbers). 45 English Note: Your radio is preprogrammed with a number of contacts per Call Lists. Check with your dealer or system administrator for more information. If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Making a Private Call from Contacts Note: Your radio must be preprogrammed to allow you to use this feature. Procedure:

Use the Options Menu. 1 > or < (on the keypad mic.) to Cnts. 2 Press the Menu Select button directly below Cnts to the call list. The display shows Contact Alias. 3 D or U to the required subscriber alias. 4 Press the Menu Select button directly below Optn. 5 D or U (on the keypad mic.) to Call and press the Menu Select button directly below Sel. 6 D or U to select the call type. s e r u t a e F d e c n a v d A 7 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 8 Press the PTT button to initiate the call. During the call, the display shows the subscriber alias. 9 Press and hold the PTT button to talk. The LED lights up solid red. OR Release the PTT button to listen. The LED lights up solid green. 10 If there is no voice activity for a programmed period of time, the call ends. OR The call ends when it reaches the maximum ring time. OR Use the PTT button:

1 > or < (on the keypad mic.) to Cnts. 2 Press the Menu Select button directly below Cnts. 3 D or U to the required subscriber alias. 4 Press the Menu Select button directly below Cnts. The display shows Contact Alias. 5 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 46 English 6 Press the PTT button to initiate the call. During the call, the display shows the subscriber alias. 7 Press and hold the PTT button to talk. The LED lights up solid red. OR Release the PTT button to listen. The LED lights up solid yellow. 8 If there is no voice activity for a preprogrammed period of time, the call ends. OR The call ends when it reaches the maximum ring time. Adding a New Contact Entry Procedure:

1 > or < (on the keypad mic.) to Cnts. 2 Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. 3 D or U to {New Contact} and press the Menu Select button directly below Sel. 4 The display shows Name. Press the Menu Select button directly below Edit. Use the keypad to enter the name. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 5 Press the Menu Select button directly below OK once you have entered the name. OR Press the Menu Select button directly below Cncl to return to the previous screen. 6 D or U to {Add Number} and press the Menu Select button directly below Sel. The display shows Type 1

<Default Type>. 7 Press Menu Select button directly below Edit. 8 D or U to the required channel and press the Menu Select button directly below OK. A d v a n c e d F e a t u r e s 47 English 9 D or U to Number 1 and press the Menu Select button directly below Edit. The display shows Number 1 and a cursor appears. Use the keypad to enter the number. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. 10 Press the Menu Select button directly below OK once you have entered the number. OR Press the Menu Select button directly below Cncl to return to the previous screen. 11 Press the Menu Select button directly below Done once you have finished. 12 The display shows <Entry> stored, confirming that the contact entry has been added. 13 The radio returns to the main Contacts screen. Deleting a Contact Entry Procedure:

1 > or < (on the keypad mic.) to Cnts. 2 Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. 3 D or U to the entry you want to delete and press the Menu Select button directly below Optn. 4 D or U to Delete and press the Menu Select button directly below Sel. The display shows <Entry> confirm del?. 5 Select Yes to delete the entry. The display shows <Entry> deleted and the radio returns to the main screen for Contacts. OR Select No to return to the main screen for Contacts. s e r u t a e F d e c n a v d A 48 English Adding a Contact to a Call List or Phone List Procedure:

1 > or < (on the keypad mic.) to Cnts. 2 Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. 3 D or U to the entry you want to add to the call list and press the Menu Select button directly below Optn. 4 D or U to Add to CallLst or Add to PhonLst and press the Menu Select button directly below Sel. 5 D or U until the display shows {Available} and press the Menu Select button directly below Add to add as a new entry. OR D or U until the display shows <ENTRY> and its associated number and press the Menu Select button directly below RPLC to replace the existing entry. 6 The display shows <ENTRY> added, confirming the addition of the contact to the list. 7 The radio returns to the main display for Contacts. Editing a Contact in a Call List or a Phone List Editing an Entry Alias Procedure:

1 > or < (on the keypad mic.) to Cnts. 2 Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. 3 D or U to the entry you want to edit and press the Menu Select button directly below Optn. 4 D or U to Edit and press the Menu Select button directly below Sel. 5 D or U to the entry alias you wish to change and press the Menu Select button directly below Edit. A d v a n c e d F e a t u r e s 6 A cursor appears. Use the keypad to edit the name. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 49 English 6 A cursor appears. Use the keypad to edit the number. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 7 Press the Menu Select button directly below OK once you have finished. The display returns to the Edit Contact screen. 8 Press the Menu Select button directly below Done to save your changes and return to the main screen for Contacts. 7 Press the Menu Select button directly below OK once you have finished. The display returns to the Edit Contact screen. 8 Press the Menu Select button directly below Done to save your changes and return to the main screen for Contacts. Editing as Entry ID Procedure:

1 > or < (on the keypad mic.) to Cnts. 2 Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. 3 D or U to the entry you want to edit and press the Menu Select button directly below Optn. 4 D or U to Edit and press the Menu Select button directly below Sel. 5 D or U to the entry ID you wish to change and press the Menu Select button directly below Edit. s e r u t a e F d e c n a v d A 50 English Editing a Call Type Procedure:

1 > or < (on the keypad mic.) to Cnts. 2 Press the Menu Select button directly below Cnts. The entries are alphabetically sorted. 3 D or U to the entry you want to edit and press the Menu Select button directly below Optn. 4 D or U to Edit and press the Menu Select button directly below Sel. 5 D or U to TYPE and press the Menu Select button directly below Edit. 6 D or U to choose from the list of call types given and press the Menu Select button directly below OK to select. 7 The display returns to the Edit Contact screen. 8 Press the Menu Select button directly below Done to save your changes and return to the main screen for Contacts. Scan Lists Scan lists are created and assigned to individual channels/

groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group. Your radio supports different types of Scan Lists:

Trunking Priority Monitor Scan List Conventional Scan List Talkgroup Scan List A maximum of 200 Scan Lists can be programmed in your radio. These lists must be preprogrammed by a qualified radio technician. A d v a n c e d F e a t u r e s Viewing a Scan List Procedure:

1 > or < (on the keypad mic.) to ScnL. 2 Press the Menu Select button directly below ScnL. 3 D or U to view the members on the list. 4 Press the H to exit the current display and return to the Home screen. 51 English Editing the Scan List This feature lets you change scan list members and priorities. Procedure:

1 > or < (on the keypad mic.) to ScnL. 2 Press the Menu Select button directly below ScnL. The display shows the lists that can be changed. 3 D or U to the entry you want to edit. 4 Press the Menu Select button directly below Sel to add and/

or change the priority of the currently displayed channel in the scan list. OR Press the Menu Select button directly below Del to delete the currently displayed channel from the scan list. OR Press the Menu Select button directly below Rcl to view the next member of the scan list. 5 D or U to select more channels to be added or deleted. OR Use the keypad to go directly to additional channels to be added or deleted. OR Use the MFK to select additional channels to be added or deleted. s e r u t a e F d e c n a v d A 6 Press H to exit scan list programming and return to the Home screen. See Viewing and Changing the Priority Status on page 53 for more information on how to add and/or change the priority of the currently displayed channel in the scan list. Changing the Scan List Status Procedure:

1 Long press the preprogrammed Scan side button. 2 D or U to the member you want to edit. 3 Press the button or press the Menu Select button directly below Sel once to add the currently displayed channel to the scan list. OR Press the button or press the Menu Select button directly below Sel, one or more times to change the scan list status icon of the currently displayed channel. 4 D or U to select more list members whose scan status you want to change. OR Use the keypad to go directly to that scan list member. OR Use the MFK to select another scan list member. 52 English 5 Press H to exit scan list programming and return to the Home screen. Scan Viewing and Changing the Priority Status Procedure:

1 Below the Sel, Del, and Rcl screen, press the Menu Select button directly below Sel to view and/or change the priority status of the currently displayed channel. OR Below the Sel, Del, and Rcl screen, press the button or press the Menu Select button directly below Sel, one or more times to view and/or change the scan list status icon of the currently displayed channel. 2 A Scan icon indicates that the current channel is in the scan list as a non-priority channel. The LED lights up solid green. OR A Priority-Two Channel Scan icon indicates that the current channel is in the scan list as the Priority-Two channel. The LED blinks green. OR A Priority-One Channel Scan icon indicates that the current channel is in the scan list as the Priority-One channel. The LED rapidly blinks green. You hear all traffic on the Priority-

One channel, regardless of traffic on non-priority channels. OR No icon indicates that the current channel is deleted from the scan list. This feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels. Turning Scan On or Off Procedure:

Press the preprogrammed Scan button. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Scan. 2 Press the Menu Select button directly below Scan. 3 The display shows Scan off if scan is disabled. Press the Menu Select button directly below Scan to enable scan. OR The display shows Scan on and the scan status icon if scan is enabled. Press the Menu Select button directly below Scan to disable scan. A d v a n c e d F e a t u r e s 4 The radio returns to the Home screen. 53 English Transmitting While the Scan is On Radio Programmed for Talkback Scan Procedure:

1 Press the PTT button to transmit on the channel indicated by the display. The radio does not begin scanning again for a predetermined hang time after you release the PTT button, allowing the other party to respond. If the other party responds within the hang time, scanning does not resume until the full hang time expires after they have finished speaking, allowing the conversation to be completed. To transmit on the selected channel if another channel is active, first turn scan off by pressing the Menu Select button below Scan momentarily. Turning Scan On While Disregarding the Squelch Code (Conventional Channels Only) Procedure:

1 > or < (on the keypad mic.) to Mon. 2 Press the Menu Select button directly below Mon. 3 The brief Monitor on display indicates that the radio is disregarding the squelch code. While scanning for activity, you can still receive fleetwide, system-wide, dynamic regrouping, incoming telephone interconnect and Private Conversation/Call Alert calls. Respond to these types of calls as you would normally on the selected channel. However, when scanning different channels while in talkgroup scan, incoming Private Conversation/Call Alert calls may be missed. s e r u t a e F d e c n a v d A 54 English Restoring a Nuisance Channel Procedure:

To restore the deleted nuisance channel, do one of the following:

Turn scan off, then on. OR Change modes. OR Turn off the radio, and then turn it back on. Nuisance mode delete can be disabled by the system administrator. Radio Programmed for Non-Talkback Scan Procedure:

1 Press the PTT button at any time to transmit on the selected channel or fixed channel. To make a Call Alert page, or Private Conversation call while scanning, press either the Menu Select button directly below Page or Call. The call is entered on the selected channel and scanning is halted until the call is exited by pressing H or pressing the Menu Select button below either Page or Call. Deleting a Nuisance Channel If a channel continually generates unwanted calls or noise

(termed a nuisance channel), you can temporarily remove the unwanted channel from the scan list. This capability does not apply to priority channels or the designated transmit channel. Procedure:

1 When the radio is locked onto the channel to be deleted,

> or < (on the keypad mic.) to Nuis. 2 Press the Menu Select button directly below Nuis. A d v a n c e d F e a t u r e s 55 English Changing Priorities Status While Scan is On While the radio is scanning, the dynamic priority change feature allows you to temporarily change any channel in a scan list

(except for the Priority-One channel) to the Priority-Two channel. This change remains in effect until scan is turned off. Scan then reverts to the preprogrammed (original) setting. Procedure:

1 Press the Menu Select button directly below Dynp to change the priority of a non-priority channel in the scan list to Priority-Two. 2 Press H momentarily to exit the scan list and resume scanning. s e r u t a e F d e c n a v d A 56 English Restoring Priorities in a Scan List Procedure:

To restore the original channel priorities in a scan list, do one of the following:

Turn scan off, then on. OR Change channels. OR Turn off the radio, and then turn it back on. Hang Up Box (HUB) To temporarily suspend Scan Mode operation, remove the control head from the Hang Up Box (HUB). You are allowed to use the control head while scan is suspended. However, Priority Member scanning is not suspended. This feature applies to all Scan Lists and Scan Types. Scan is resumed once the control head is returned to the holding clip and the preprogrammed hang time has elapsed. Note: Priority Scan List members are continuously scanned only when the Scan List, Designated Tx Member field is set to Talkback in the radio programming. Otherwise, all scan mode operation is suspended. Call Alert Paging This feature allows your radio to work like a pager. Even if other users are away from their radios, or if they are unable to hear their radios, you can send them an individual Call Alert page. You can also verify if a radio is active on the system. Depending on how your radio is programmed, when you make an Enhanced Private Call, the radio either automatically sends a Call Alert page if there is no answer after the maximum ring time, OR when you press the PTT button. Note:

This feature must be preprogrammed by a qualified radio technician. Receiving a Call Alert Page Procedure:

When you receive a Call Alert page 1 You hear four repeating alert tone and the green LED blinks. OR You hear one alert tone and the green LED blinks if Call Alert Tone Auto Reset is enabled. 2 The call received icons blinks and the display shows Page received. 3 Press the PTT button to answer. OR Press any button to clear the Call Alert page. See Making a Talkgroup Call on page 35 or Making a Private Call (Trunking Only) on page 36 for more information. A d v a n c e d F e a t u r e s 57 English Sending a Call Alert Page Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure:

Press the preprogrammed Quick Access (One-Touch) Call Alert Paging button to send a page to the preprogrammed ID and proceed to Step 5 of the procedure below. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Page. 2 Press the Menu Select button directly below Page. 3 D or U to select the required ID. 4 Press the PTT button to send the page. 5 The display shows Paging...<Number> or <Alias>. 6 If the call alert page is sent successfully, four highpitch tone sounds and the display shows Ack received. OR If the call alert page is not acknowledged, a low tone sounds and the display shows No acknowledge. s e r u t a e F d e c n a v d A 58 English 7 The radio returns to the Home screen. OR Press the Menu Select button directly below OK to return to the main screen for Contacts. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Call. 2 Press the Menu Select button directly below Call. 3 D or U to select the required ID, press the PTT button to initiate the call. 4 If the target radio does not respond after a preprogrammed period of time, the display shows Send page?. 5 Press the Menu Select button directly below Yes to send the call alert page. OR Press the Menu Select button directly below No to exit the screen without sending the call alert page. 6 The display shows Paging...<Alias>. 7 If the call alert page is sent successfully, a tone sounds and the display shows Ack received. OR If the call alert page is not acknowledged, a low tone sounds and the display shows No acknowledge. 8 The radio returns to the Home screen. OR Press the Menu Select button directly below OK to return to the main screen for Contacts. In-Call User Alert You can enable and disable voice transmission, if needed. Procedure:

1 Make sure you are in Home mode where the default zone and mode are being displayed. 2 > or < (on the keypad mic.) to scroll to the Vmut. 3 Press the Menu Select button directly below Vmut. 4 Press the Menu Select button directly below Vmut or the VMut preprogrammed button again to turn the feature off and you will be able to hear to normal dispatch calls. Pressing the Menu Select button directly below Vmut or the VMut programmed button momentarily toggles between Voice mute on and Voice mute off. Voice mute on shown on the display indicates that the radio is muted to all conventional dispatch calls and affiliated trunking group calls. Emergency Operation The Emergency feature is used to indicate a critical situation. If the Orange button is preprogrammed to send an emergency signal, this signal overrides any other communication over the selected channel. Your radio supports 5 Emergency modes:

Emergency Call Emergency Alarm Emergency Alarm with Call Silent Emergency Alarm Special Considerations for Emergencies Check with your dealer or system administrator for more information on the programming of this feature. Only one of the Emergency modes above can be assigned to the preprogrammed Emergency button or the Emergency footswitch. Note:

To exit emergency at any time, press and hold the preprogrammed Emergency button for about a second. A d v a n c e d F e a t u r e s 59 English Sending an Emergency Alarm This feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher. Procedure:

1 Press the preprogrammed Emergency button. A tone sounds and the display alternates Emergency and the home display. 2 A dispatcher acknowledgment Ack received display follows. AND, Trunking Only:

A high-pitched tone indicates that the alarm has been received by the trunked systems central controller. 3 Press and hold the emergency button or the PTT button to return to normal operation. Sending an Emergency Call (Trunking Only) Procedure:

1 Press preprogrammed Emergency button. 2 A tone sounds and the display alternates Emergency and the home display. OR A short low-pitched tone sounds when the selected channel does not support emergency. s e r u t a e F d e c n a v d A 60 English 3 Hold the microphone vertically 1 to 2 inches (2.0 to 2.5 cm) from your mouth. 4 Press and hold the PTT button. Speak clearly into the microphone. 5 Release the PTT to end the transmission. 6 Press and hold the preprogrammed Emergency button until a tone sounds to exit Emergency mode. Sending an Emergency Alarm with Emergency Call This feature allows you to send an Emergency Alarm to another radio. Upon acknowledgement, both radios can communicate over a preprogrammed Emergency channel. If the radio has both emergency call and alarm features enabled, it automatically proceeds to the call mode after the alarm is acknowledged. Procedure:

1 Press the preprogrammed Emergency button to activate the emergency call/alarm feature. 2 The display alternates Emergency and the home display. 3 A high-pitched tone sounds, indicating that the alarm has been received by the trunked systems central controller. A dispatcher acknowledgment (four high-pitched tones) follows, accompanied by an Ack received display. 4 Hold the microphone vertically 1 to 2 inches (2.0 to 2.5 cm) from your mouth. 5 Press and hold the PTT button. Speak clearly into the microphone. 6 Release the PTT to end the transmission. 7 Press and hold the preprogrammed Emergency button until a tone sounds to exit Emergency mode. Turning the radio off also cancels the emergency state. Sending a Silent Emergency Alarm This feature allows you to send an Emergency Alarm to another radio without any audio or visual indicator. Upon acknowledgement, your radios microphone is automatically activated, allowing you to communicate with the other radio without pressing the PTT button. This activated microphone state is also known as hot mic. Note:

If you press the PTT button during hot mic, and continue to press it after the hot mic duration expires, the radio continues to transmit until you release the PTT button. Procedure:

1 Press the preprogrammed Emergency button to activate the silent alarm feature. 2 Press and hold the emergency button until a tone sounds to exit the silent alarm mode. If silent emergency alarm is used with emergency call, pressing the PTT button exits the silent mode and initiates the emergency call. A d v a n c e d F e a t u r e s 61 English Special Considerations for Emergencies If you press the emergency button while in a channel that has no emergency capability, a low-pitched tone sounds. If the unit is out of the range of the system and/or the emergency alarm is not acknowledged, a tone sounds and the display shows No acknowledge. If you press the emergency button, then change to a mode that has no emergency capability, the display shows No Emergency and a continuous low-pitched tone sounds until a valid emergency mode is selected or until the emergency is cancelled. When an emergency is active, changing to another mode where emergency is enabled (trunked or conventional) causes an emergency alarm and/or emergency call to be active on the new mode. s e r u t a e F d e c n a v d A 62 English Advanced FeaturesAutomatic Registration Service (ARS) This feature provides an automated data application registration for the radio. When you turn on the radio, the device automatically registers with the server. Data applications within the fixed network can determine the presence of a device on the system and send data to the device. For example: Text Messaging Service (TMS). The Automatic Registration Service for the radio consists of two

(2) modes:

ARS Server Mode (default mode) ARS Non Server Mode Note:

The default ARS mode can be changed by a qualified radio technician using the radios programming software. Selecting or Changing ARS Mode Procedure:

1 After the zone you want is displayed, toggle until the display shows the required channel. OR Press and hold > or < (on the keypad mic.) to Chan. Press the Menu Select button directly below Chan. The display shows the current zone is not blinking, and the channel is blinking. 2 D or U or press the MFK once and rotate the MFK to the desired channel. 3 In ARS Server Mode, the display shows the User Login Indicator icon, the zone, and ARS server channel. OR In ARS Non-Server Mode, the display shows the User Login Indicator icon, the zone, and ARS non-server channel. OR If the channel or mode selected is unprogrammed, the display shows Unprogrammed. Repeat Step 2. 4 Press H to confirm the displayed zone and channel. A d v a n c e d F e a t u r e s 63 English Accessing the User Login Feature This feature allows you as the user to be associated with the radio. With this association, every data application (Example:

Text Messaging Service) takes on a friendly username. You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message. Note: Valid characters for a username entry are capital letters

(A Z), small letters (a z), numbers (0 9), symbols

(*, #, -, /), and the space character. The maximum length for a username is eight (8) characters. Usernames are not case sensitive in server mode but are case sensitive in non-server mode. A predefined username may sometimes be invalid because the programming software that is used to set predefined usernames allows you to set usernames comprising of eight (8) characters or more. s e r u t a e F d e c n a v d A 64 English Logging In as a User Procedure:

1 > or < (on the keypad mic.) to User. 2 Press the Menu Select button directly below User. 3 The display shows the User Login screen. 4 Press the Menu Select button directly below ID. 5 A blinking cursor appears beside ID. Use the keypad to enter a username using the keypad multi-tap function. OR D or U to scroll through the list of predefined usernames. Press the Menu Select button to select a predefined username. OR Press and hold D or U to scroll through the list of predefined usernames at a fast scroll rate. Press the Menu Select button directly below Logn to select a predefined username. 6 If the selected predefined username has more than eight (8) characters, or an invalid character in it, the display momentary shows Invalid ID. Repeat Step 5. OR Press the Menu Select button directly below PIN. 7 A blinking cursor appears beside PIN. Enter your Personal Identification Number (PIN) number. The maximum PIN length is 4 digits. The PIN number will appear as asterisks. 8 Press the Menu Select button directly below Logn. 9 In ARS server mode, the display shows the User Login Indicator icon, the ID, In progress and Cncl. OR In ARS non-server mode, the display shows the User Login Indicator icon, the ID, Logged in and Logt. In non-ARS enabled mode, the display shows Offline and Logt. 10 If the username is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also momentary shows Login failed. Repeat step 5. OR If the PIN is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also momentary shows Login failed. Repeat Step 7. OR Press the Menu Select button directly below Cncl to cancel the login in progress screen and return to the initial user login screen. OR Wait for the logged in confirmation screen. If the login process is successful, the display shows the successful user login indicator (IP indicator) icon and Logged in and Logt. Logging Out Once the data application registration is completed, you can log out. Procedure:

1 > or < (on the keypad mic.) to Logt. 2 Press the Menu Select button directly below Logt. 3 Display shows the User Login Indicator icon and Clear private data?. 4 Select Yes to clear all your private data. The display shows momentary Private data cleared. OR Select No to keep your private data. Note: Private data refers to all messages in the text messaging Inbox, Draft and Sent folder. The next radio user will be able to access your Inbox, Draft and Sent messages if private data is not deleted. A d v a n c e d F e a t u r e s 65 English Text Messaging Service (TMS) This feature allows you to send and receive text messages. The maximum length of characters for a text message is 200. There are three (3) types of text messages:

A new text message (free form message) A predefined message (quick text message) An edited quick text message The main menu consists of the following options:

Inbox Compose Drafts Sent Note: See Status Icons on page 21 for more details on the TMS icons and TMS Menu Options on page 22 for more details on each menu option. s e r u t a e F d e c n a v d A 66 English Accessing TMS Feature Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Press the Menu Select button directly below Back at any time to return to the previous screen. Procedure:

Press the preprogrammed Data Feature button or the TMS button to access the TMS feature screen. OR Press and hold the preprogrammed Data Feature button or the TMS button to access the Inbox screen. OR Follow the procedure below. 1 > or < (on the keypad mic.) to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 D or U to scroll through the main menu options. Composing and Sending a New Text Message Note: During the uppercase and lowercase mode, multi-

tapping the keys only scrolls through the letters. For example, A->B->C, a->b->c. During the num lock mode, except for 1, pressing the keypad only enters the numeric digits. Subsequent presses of the same key inserts the same digit to the text message (no multi-tap). Procedure:

1 > or < (on the keypad mic.) to f. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 D or U to Compose. Press the Menu Select button directly below Compose to see the compose options. 4 Press the Menu Select button directly below New to compose a new message. 5 A blinking cursor appears on the Compose screen. Use the keypad to type or edit your message. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase A d v a n c e d F e a t u r e s mode, and lowercase mode. Press # to toggle between numeric and letter mode. 6 Press the Menu Select button directly below Optn once the message is composed. 7 D or U to Send and press the Menu Select button directly below Send to send. OR D or U to Back and press the Menu Select button directly below Back to return to Compose screen if you want to edit the message. 8 D or U to scroll through the address list and press the Menu Select button below Sel to select the required address. OR D or U to {Other recpnt} and press the Menu Select button below Edit. A blinking cursor appears in the Enter address screen. Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 67 English 9 Press the Menu Select button below Send to send the message. OR Press the PTT button to send the message. 10 The display shows the Send message screen and Sending msg. 11 If the message is sent, a tone sounds and the display shows Msg sent. OR If the message is not sent, a low tone sounds and the display shows Send failed. If the message fails to send, the radio returns you to the main TMS screen. Note: You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 70 for more information. Note: You can also select the DRFT option to save your message in the Drafts folder to send it at a later time. See Accessing the Drafts Folder on page 74 for more details. s e r u t a e F d e c n a v d A 68 English Sending a Quick Text Message Quick Text messages are messages that are predefined and usually consist of messages that are used most frequently. Each Quick Text message has a maximum length of 50 characters. Procedure:

Press the preprogrammed Quick Text button and proceed to Step 3. OR Follow the procedure below. 1 > or < (on the keypad mic.) to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 D or U tto Compose. Press the Menu Select button directly below Compose to access the compose options. 4 D or U to List. 5 D or U to scroll through the list of messages and press the Menu Select button directly below Sel to select the required message. 6 The message appears on the Compose screen, with a blinking cursor at the end of it. Use the keypad to edit the message. Press < to move one space to the left. 10 Press the Menu Select button below Send to send the message. OR Press the PTT button to send the message. 11 The display shows the screen and Sending msg. 12 If the message is sent, a tone sounds and the display shows Msg sent. OR If the message is not sent, a low tone sounds and the display shows Send failed. If the message fails to send, the radio returns you to the main TMS screen. Note: You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 70 for more information. A d v a n c e d F e a t u r e s Press > to move one space to the right. Press the Menu Select button directly below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 7 Press the Menu Select button directly below Optn. 8 D or U to Send and press the Menu Select button directly below Sel to send the message. 9 D or U to scroll through the address list and highlight the required address. OR D or U to {Other recpnt} and press the Menu Select button below Edit. A blinking cursor appears in the Enter address screen. Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 69 English Using the Priority Status and Request Reply Features Before sending your message, you can append a priority message and/or a request reply to your message. Appending or Removing a Priority Status to a Text Message Note:

The Priority Message icon on a message does not imply that the message gets higher priority over the other messages when it is being transmitted. It is just an indication that can be embedded into a message to let the receiver know that the message is important. Procedure:

After the outgoing message is composed (see Composing and Sending a New Text Message on page 67 for more information):

1 Press the Menu Select button directly below Optn. 2 Press the Menu Select button directly below Impt. The priority status icon appears beside the normal message icon on the label bar. 3 Press the Menu Select button directly below Impt again. The priority status icon and the normal message icon disappear from the label bar. s e r u t a e F d e c n a v d A 70 English Appending or Removing a Request Reply to a Text Message Procedure:

After the outgoing message is composed (see Composing and Sending a New Text Message on page 67 for more information):

1 Press the Menu Select button directly below Optn. 2 Press the Menu Select button directly below Rqrp. The reply status icon appears beside the normal message icon on the label bar. 3 Press the Menu Select button directly below Rqrp again. The reply status icon and the normal message icon disappear from the label bar. Appending a Priority Status and a Reply Request to a Text Message Procedure:

After the outgoing message is composed (see Composing and Sending a New Text Message on page 67 for more information):

1 Press the Menu Select button directly below Optn. 2 D or U to Impt and press the Menu Select button directly below Impt to indicate the message as important. AND D or U to Rqrp and press the Menu Select button directly below Rqrp to request for a reply. 3 The priority status and reply status icons appear beside the normal message icon on the label bar. Removing a Priority Status and a Reply Request from a Text Message When an outgoing message is indicated with priority status and reply status icons, follow the procedure below to remove these indicators. Procedure:

1 Press the Menu Select button directly below Optn. 2 U or D to Impt and press the Menu Select button directly below Impt to remove the priority status icon. AND D or U to Rqrp and press the Menu Select button directly below Rqrp to remove the reply status icon. 3 The priority status, reply status and normal message icons disappear from the label bar. Managing Text Messages Receiving a Text Message Note: When you receive a message that is flagged with the Request Reply icon, you must manually respond to the sender that you have received the message. The system will not automatically send back a notification that the radio has received such message. Procedure:

When you receive a message, press and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox and go to Step3. OR Follow the procedure below. 1 The new message icon appears and the display momentarily shows New msg. 2 Press the Menu Select button directly below TMS to access the message. 3 The display shows alias or ID with the sender of the latest received message on top. A d v a n c e d F e a t u r e s 71 English Select Del to delete the message. Select Back to return to the previous screen. Note:

The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) on page 66 for more information. Viewing a Text Message from the Inbox The Inbox can hold up to thirty (30) messages. Note: D or U to read the message if fills more than one screen. Procedure:

Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3. OR Press and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox screen and proceed to Step 4. OR Follow the procedure below. 1 > or < (on the keypad mic.) to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 Press the Menu Select button below Inbox to view Inbox feature screen. 4 The display shows alias or IDs, with the sender of the latest received message. While on the review message screen, press the Menu Select button directly below Rply, Del, or Back to access the option. Select Rply to reply the message. s e r u t a e F d e c n a v d A 72 English Replying to a Received Text Message Note:

The original date and time stamp, address and message content is automatically appended to the reply message. Procedure:

1 D or U to the required aliases or ID and press the Menu Select button below Sel to view the message. 2 Press the Menu Select button directly below Rply to reply to a message. 3 D or U to NEW and press the Menu Select button directly below NEW. OR D or U to LIST and press the Menu Select button directly below LIST for a predefined message. OR D or U to scroll through the list of messages and press the Menu Select button directly below Sel to select the required message. 4 A blinking cursor appears on the screen. OR The predefined message appears on the Compose screen, with a blinking cursor at the end of it. 5 Use the keypad to type or edit your message. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 6 Press the Menu Select button directly below Optn once you have finished writing the message. 7 D or U to Send and press the Menu Select button directly below Send to send the message. 8 The display shows the Send Message screen and Sending msg. Press the Menu Select button directly below Back at any time to return to the previous screen. Note: You can append a priority message and/or a request reply to your message. Using the Priority Status and Request Reply Features on page 70 for more information. A d v a n c e d F e a t u r e s 73 English Accessing the Drafts Folder This folder stores the messages that were saved previously. The Drafts folder can hold up to 10 messages. The oldest draft in the folder is deleted when the 11th message comes in. Procedure:

1 > or < (on the keypad mic.) to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 D or U to DRFT and press the Menu Select button below DRFT. 4 The display shows the first draft message. Press the Menu Select button directly below Edit, Del, or Back to access the option. Select Edit to edit the message before sending it. Select Del to delete the message. Select Back to return to the previous screen. s e r u t a e F d e c n a v d A 74 English Managing Sent Text Messages Once a message is sent to another radio, it is saved in the Sent folder. The most recent sent text message is always added to the top of the Sent list. The Sent folder is capable of storing a maximum of ten (10) last sent messages. When the folder is full, the oldest text message in the folder is deleted when the 11th message comes in. Viewing a Sent Text Message The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) on page 66 for more information. Procedure:

Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3. OR Follow the procedure below. 1 > or < (on the keypad mic.) to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 D or U to Sent and press the Menu Select button below Sent. Press the Menu Select button directly below Optn, Del, or Back to access the option. Select Optn to send to the message. Select Del to delete the message. Select Back to return to the previous screen. Note:

The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) Icons on page 21 for more information. Sending a Sent Text Message Procedure:

1 Press the Menu Select button directly below Optn while viewing the message. 2 D or U to Send and press the Menu Select button directly below Send to send the message. 3 D or U to scroll through the address list and highlight the required address. OR D or U to {Other recpnt} and press the Menu Select button below Edit. A blinking cursor appears in the Enter address screen. Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 4 Press the Menu Select button below Send or the PTT button to send the message. 5 The display shows the Send Message screen and Sending msg. 6 Press the Menu Select button directly below Back to return to the previous screen. Note: You can append a priority message and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 70 for more details. A d v a n c e d F e a t u r e s 75 English Deleting Text Messages Procedure:

From the Inbox, Draft, or Sent screen:

1 D or U to scroll through the messages. 2 Press the Menu Select button directly below Del to view the delete options. 3 Press the Menu Select button directly below Curr to delete the current message. OR Press the Menu Select button directly below All to delete all the messages. s e r u t a e F d e c n a v d A 76 English Secure Operations Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels. Unlike other forms of security, Motorola digital encryption provides signaling that makes it virtually impossible for others to decode any part of an encrypted message. Managing Encryption Note: Refer to the Key-Variable Loader (KVL) manual for equipment connections and setup. Loading a Single Encryption Key Procedure:

1 Attach the KVL to your radio. Upon attaching the KVL, the radio display shows Keyloading. 2 Press the Menu Select button below Target. 3 Press the Menu Select button below Load. 4 Press the Menu Select button below Key. 5 D or U to required key. 6 Press the Menu Select button below Load to load the key to your radio. 7 When the key has been loaded successfully, the radio sounds a short tone for single-key radios. Loading the Group Encryption Keys Procedure:

1 Attach the KVL to your radio. 2 Press the Menu Select button below Target. 3 Press the Menu Select button below Load. 4 Press the Menu Select button below Group. 5 D or U to required group. 6 Press the Menu Select button below Load to load the key to your radio. 7 Your mobile radio display shows Keyloading when it is loading key(s) from KVL. 8 When the key has been loaded successfully, the radio sounds an alternating tone for multikey radios. Using the Multikey Feature This feature allows the radio to be equipped with different encryption keys and supports the DES-OFB algorithm. There are two types of multikey:

Conventional Multikey The encryption keys can be tied

(strapped), on a one-per-channel basis, through Customer Programming Software. In addition, you can have operator-

selectable keys, operator-selectable keysets, and operator-

selectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups. Trunked Multikey If you use your radio for both conventional and trunked applications, you have to strap your encryption keys for trunking on a per-talkgroup or announcement-group basis. In addition, you may strap a different key to other features, such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operator-

selectable key erasure. A d v a n c e d F e a t u r e s 77 English Selecting an Encryption Key (Conventional Only) Procedure:

Enabling Secure Transmission Procedure:

1 > or < (on the keypad mic.) to Key. 2 Press the Menu Select button directly below Key. The display shows the last user-selected and stored encryption key, and the available menu selections. 3 D or U to scroll through the encryption keys. OR Use the keypad to enter the number of the desired key. 4 Press the Menu Select button directly below Sel to save the newly selected key and return to the Home screen. OR Press H, the PTT button, or the Menu Select button directly below Exit to exit. Note:

If the selected key is erased, a momentary keyfail tone sounds and the display shows Key fail. OR If the selected key is not allowed, a momentary illegal key tone sounds and the display shows Illegal key. 1 > or < (on the keypad mic.) to Sec and press the Menu Select button directly below Sec. The display shows m and the current key if multi-key has been enabled. 2 Monitor the mode to be sure it is not in use. 3 Press PTT button to transmit. Note:

If the selected channel is preprogrammed for clear-only operation when you press the PTT button, an invalid mode tone sounds and the display shows Clear Tx only. The radio does not transmit until you disable the secure mode. The radio can be configured to ignore the clear voice or insecured transmission when the radio is in secured transmission. Check with your agent for details. s e r u t a e F d e c n a v d A 78 English Accessing the Secure Feature Procedure:

1 > or < (on the keypad mic.) to Sec. 2 Press and hold the Menu Select button directly below Sec to display Secure feature screen. 3 The display shows the Secure screen. Selecting a Keyset This feature allows you to select one or more groups of several encryption keys from among the available keys stored in the radio. For example, you could have a group of three keys structured to one keyset, and another group of three different keys structured to another keyset; by changing keysets, you would automatically switch from one set of keys to the other. Every channel to which one of the original keys was tied now has the equivalent new key instead. Note: Press H, the PTT button, or the Exit menu selection to exit this menu at any time without changing the keyset selection. Procedure:

1 > or < (on the keypad mic.) to Kset. A d v a n c e d F e a t u r e s 2 Press the Menu Select button directly below Kset. The display shows the last user-selected and stored keyset, and the available keyset menu selections. 3 D or U to scroll through the keysets. OR Use the keypad to enter the number of the desired keyset. 4 Press the Menu Select button directly below Sel to save the newly selected keyset. 5 The radio exits keyset selection and returns to the Home screen. Erasing the Selected Encryption Keys This feature allows you to erase all or selected encryption keys. Procedure:

1 > or < (on the keypad mic.) to Eras. 2 Press the Menu Select button directly below Eras. The display shows the last user-selected and stored encryption key, and the available menu selections. 3 D or U to the desired encryption key. OR Use the keypad to enter the number of the desired key. 4 Press the Menu Select button directly below All to delete all keys. OR 79 English Press the Menu Select button directly below Sngl to delete current shown key. OR Press the Menu Select button directly below Abrt to abort this screen and return to Home screen. Requesting an Over-the-Air Rekey This feature, also known as OTAR, allows the dispatcher to reprogram the encryption keys in the radio remotely. The dispatcher performs the rekey operation upon receiving a rekey request from the user. Procedure:

1 > or < (on the keypad mic.) to Rekey. 2 Press the Menu Select button directly below Rekey. 3 Press the PTT button to send the rekey request. OR Press the PTT button again, or the H or Emergency button, to exit the feature and transmit in normal mode. 4 If the rekey operation fails, a bad-key tone sounds and the display shows Rekey fail. Note:

The rekey operation failure indicates that your radio does not contain the Unique Shadow Key (USK). This key must be loaded into the radio with the key-variable loader (KVL) before the rekey request can be sent. s e r u t a e F d e c n a v d A 80 English Refer to your local key management supervisor for more information. MDC Over-the-Air Rekeying (OTAR) Page This feature allows to view or define MDC Over-the-Air Rekeying (OTAR) features.It is applied only when operating in secure encrypted mode and only for conventional communications. In additional to Rekey Requests, OTAR transmissions include Delayed Acknowledgements, and Power-

up Acknowledgements. Some of the options selected may also need to be set up at the Key Management Controller (KMC) site to work properly. Note:

This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. Infinite UKEK Retention This feature enables Unique Key Encryption Key (UKEK) to be permanently stored in the radio even when all of the encryption keys is erased. Without this UKEK key, the radio could not be over the air rekeyed. Note:

This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. Hear Clear There are two components of Hear Clear. 1 Companding:

Reduces the channel noise, e.g. OTA transmission, that is predominantly present in UHF2 and 900 MHz channel with the following features. Compressor reduces the background noise flow and the speech signal at transmitting radio. Expander expands the speech while the noise flow remains the same at receiving radio. 2 Random FM Noise Canceller (Flutter Fighter):

Reduces the unwanted effects of random FM noise pulses caused by channel fading under high Signal-to-Noise (S/N) conditions such as in a moving in a transportation. The fading effects, heard as audio pops and clicks, are cancelled without affecting the desired audio signal. The Random FM Noise Canceller operates only in receive mode. Note:

This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. The Global Positioning System (GPS) This feature uses information from the Global Positioning System (GPS) satellites orbiting the Earth to determine the approximate geographical location of your radio, expressed as latitude and longitude. The availability and accuracy of this location information (and the amount of time that it takes to calculate it) varies depending on the environment in which you are using the GPS feature. For example, GPS location fixes are very difficult to obtain indoors, in covered locations, between high buildings, or in situations where you have not established a clear broad view of the sky. A d v a n c e d F e a t u r e s Understanding the GPS Feature The GPS technology uses radio signals from earth orbiting satellites, to establish the location co-ordinates, maximizing your view of clear unobstructed sky is essential for optimum performance. Where adequate signals from multiple satellites are not available (usually because you cannot establish a view of a wide area of the sky), the GPS feature of your radio will not work. Such situations include but are not limited to:

In underground locations Inside of buildings, trains, or other covered vehicles 81 English Under any other metal or concrete roof or structure Between tall buildings or under dense tree-cover In temperature extremes outside the operating limits of your radio Even where location information can be calculated in such situations, it may take longer to do so, and your location estimate may not be as accurate. Therefore, in any emergency situation, always report your location to your dispatcher. Note: Even where adequate signals from multiple satellites are available, your GPS feature only provides an approximate location, usually within 20 meters from your actual location, but sometimes further away. Keep in mind that the accuracy of the location information and the time it takes to obtain it varies depending upon circumstances, particularly the ability to receive signals from an adequate number of satellites. Note:

The satellites used by the GPS feature are controlled by the U.S. government and are subject to changes implemented in accordance with the Department of Defense GPS user policy and the Federal Radio Navigation Plan. These changes may affect the performance of the GPS feature on your radio. Enhancing GPS Performance Sometimes, the GPS feature may be unable to complete a location calculation successfully. You then see a message indicating that your radio cannot connect to enough visible satellites. To maximize the ability of your radio to determine a fix, please note the following guidelines:

For your initial fix, hold the radio in the face position. Stay in the open. The GPS feature works best where there is nothing between your radio and a large amount of open sky. The Outdoor Location Feature (Using GPS) This feature allows you to determine your current location using a location menu, as well as your current distance and bearing in relation to another location. Radio location may be requested and reported over-the-air. Your radio stores up to a maximum of sixty (60) programmable location coordinates, also known as waypoints. When the memory is full, the next waypoints automatically replaces the oldest waypoints in the radio. s e r u t a e F d e c n a v d A 82 English The radio also stores four (4) preprogrammed waypoints. These coordinates cannot be deleted. Programmable Waypoints User-configurable location coordinates. Only the alias is editable, not the coordinates. Coordinates can be deleted one at a time, or all at once. Preprogrammed Waypoints Fixed location coordinates:

Home Emergency Last Known Location Destination The Home and Destination coordinates are editable. Coordinates cannot be deleted. Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. A d v a n c e d F e a t u r e s Accessing the Outdoor Location Feature Note: An ON menu key may be present on the location menu if it is preprogrammed by the dealer or system administrator. Procedure:

1 > or < (on the keypad mic.) to Loc. 2 Press the Menu Select button directly below Loc. The display shows Location off <Latitude>. 3 Press the Menu Select button directly below On to turn on the GPS. The display shows Previous loc <Latitude>. 4 U or D to check the longitude, time and date of the last successful location fix. 5 Press the Menu Select button directly below Rfsh to obtain a new location fix. 6 The top line temporarily displays Please wait while the new location is being determined. While the new location is being determined, the location signal can be a solid or blinking icon. 7 Once the location coordinates are fixed, the display shows the current latitude. Toggle to see the longitude, time and date. The location coordinates are updated automatically every five seconds while the location signal is present. 8 Press the Menu Select button directly below Exit to exit the feature and return to the main screen. 83 English OR Press H or the PTT button (if preprogrammed) to exit this menu. OR Follow the procedure below to turn off the GPS (This feature is enabled by a qualified radio technician.):

1 > or < (on the keypad mic.) to Loc. 2 Press the Menu Select button directly below Loc. The display shows Previous loc <Latitude>. 3 U or D to check the longitude, time and date of the last successful location fix. 4 Press the Menu Select button directly below Optn. 5 > or < (on the keypad mic.) to Turn off GPS (if preprogrammed). 6 Press the Menu Select button directly below Sel to turn off the GPS. The display shows Location off. 7 Press the Menu Select button directly below Exit to exit the feature and return to the main screen. OR Press H or the PTT button (if preprogrammed) to exit this menu. s e r u t a e F d e c n a v d A The radio also exits the menu if the emergency button is pressed. 84 English Saving a Waypoint Procedure:

While in the current location display:

1 Press the Menu Select button directly below Optn. 2 U or D to Save as waypt and press the Menu Select button directly below Sel. OR U or D to Save as home and press the Menu Select button directly below Sel and proceed to Step 5. OR U or D to Save as dest. and press the Menu Select button directly below Sel and proceed to Step 5. 3 A blinking cursor appears in the screen. Use the keypad to type the alias via multi-tap. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 4 Press the Menu Select button directly below OK once you are done. 5 The display shows Saved as <Waypoint name>. OR The display shows Saved as home. OR The display shows Saved as dest.. 6 Press H or the PTT button (if preprogrammed) to exit this menu. Viewing a Saved Waypoint Procedure:

While in the current location display:

1 Press the Menu Select button directly below Optn. 2 > or < (on the keypad mic.) to Waypoints. 3 Press the Menu Select button directly below Sel. 4 D or U to desired waypoint. 5 Press the Menu Select button directly below Optn. The display shows View. 6 Press the Menu Select button directly below Sel. 7 D or U again to view longitude, time and date the waypoint was detected. 8 Press the Menu Select button directly below Back to return to previous Waypoint screen. OR Press H or the PTT button (if preprogrammed) to exit this menu. A d v a n c e d F e a t u r e s 85 English Editing the Alias of a Waypoint Procedure:

While in the current location display:

1 Press the Menu Select button directly below Optn. 2 > or < (on the keypad mic.) to Waypoints. 3 Press the Menu Select button directly below Sel. 4 D or U to desired waypoints. 5 Press the Menu Select button directly below Optn. 6 D or U to Edit name and press the Menu Select button directly below Sel. 7 A blinking cursor appears in the Edit Name screen. Use the keypad to edit the alias. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 8 Press the Menu Select button directly below OK once you s e r u t a e F d e c n a v d A are done. OR 86 English Press the Menu Select button directly below Cncl to return to the Waypoints main screen. 9 The display shows <Waypoint Name> updated. 10 Press H or the PTT button (if preprogrammed) to exit this menu. Editing the Coordinates of a Waypoint Procedure:

While in the current location display:

1 Press the Menu Select button directly below Optn. 2 > or < (on the keypad mic.) to Waypoints and press the Menu Select button directly below Sel. 3 D or U to desired waypoints. 4 Press the Menu Select button directly below Optn. 5 D or U to Edit location and press the Menu Select button directly below Sel. 6 The first number blinks. Press < to move to the previous number/coordinates. Press > to move to the next number/coordinates. Press U or D to change the North (N), South (S), East (E) or West (W) direction. Press the Menu Select button below Edit to change the number/coordinates. 7 A blinking cursor appears in the Edit location screen. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. 8 Press the Menu Select button directly below OK once you are done. OR Press the Menu Select button directly below Cncl to return to the previous screen. 9 Press the Menu Select button directly below OK once you are done with the new coordinates. OR Press the Menu Select button directly below Cncl to return to the previous screen then skip to step 11. 10 The display shows {Home} Updated and the radio returns to the Waypoints main screen. OR The display shows {Destination} Updated and the radio returns to the Waypoints main screen. 11 Press H or the PTT button (if preprogrammed) to exit this menu. Deleting a Single Saved Waypoint Procedure:

While in the current location display:

1 Press the Menu Select button directly below Optn. 2 > or < (on the keypad mic.) to Waypoints. 3 Press the Menu Select button directly below Sel. 4 D or U to desired waypoints. 5 Press the Menu Select button directly below Optn. OR Press the Menu Select button directly below Del and then skip to step 7. A d v a n c e d F e a t u r e s 6 D or U to Delete and press the Menu Select button directly below Sel. 7 The display shows <Waypoint Name> confirm del?. 8 Press the Menu Select button directly below Yes to delete. The display shows <Waypoint Name> deleted. OR Press the Menu Select button directly below No to return to previous Waypoint screen. 9 Press H or the PTT button (if preprogrammed) to exit this menu. 87 English Measuring the Distance and Bearing from a Saved Waypoint Procedure:

While in the current location display:

1 Press the Menu Select button directly below Optn. 2 D or U to Dist frm here and press the Menu Select button directly below Sel. 3 D or U to the required waypoint, and press the Menu Select button directly below Sel. 4 The display shows the distance and bearing from the current to the selected coordinates. 5 Press the Menu Select button directly below Back to return to the previous Waypoint screen. OR Press H or the PTT button (if preprogrammed) to exit this menu. Deleting All Saved Waypoints Procedure:

1 Press the Menu Select button directly below Optn. 2 > or < (on the keypad mic.) to Waypoints and press the Menu Select button directly below Sel. 3 D or U to desired waypoints and press the Menu Select button directly below Optn. 4 D or U to Delete all and press the Menu Select button directly below Sel. 5 The display shows All saved wayp confirm del?. 6 Press the Menu Select button directly below Yes to delete. The display shows All saved wayp deleted. OR Press the Menu Select button directly below No to return to previous Waypoint screen. 7 Press H or the PTT button (if preprogrammed) to exit this menu. s e r u t a e F d e c n a v d A 88 English Using the Location Feature While in Emergency Mode When the Emergency feature is activated by pressing the emergency button, the radio exits the Location menu and returns to the home (default) display so that you can see which channel the emergency signal is going out on. However, you may re-enter the Location menu while still in emergency mode, provided that Silent Emergency has not been activated. If you have turned Location off using the ON/OFF menu key, it automatically turns back on when Emergency is activated. If there is a solid location signal during Emergency, the current location and the location information received is saved as Emergency and Last Known Location waypoints, respectively. Trunking System Controls Using the Failsoft System The failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel. The failsoft condition is indicated by a faint beeping tone every nine seconds (radio unsquelched) until the trunking system returns to normal operation. To continue, in Failsoft, to communicate with other talkgroups, refer to the following procedure. Procedure:

1 Rotate the MFK to change to a different repeater frequency. 2 Press the PTT button to talk, and release the button to listen. A d v a n c e d F e a t u r e s When the trunking system returns to normal operation, your radio automatically leaves failsoft operation and returns to trunked operation. 89 English Going Out-of-Range OUT OF RANGE when your radio goes out of the range of the system, it can no longer lock onto a control channel. Procedure:

1 A low-pitched tone sounds. AND/OR The display shows the currently selected zone/channel combination and Out of range. 2 Your radio remains in this out-of-range condition until:

It locks onto a control channel. OR It locks onto a failsoft channel. OR It is turned off. s e r u t a e F d e c n a v d A 90 English SmartZone The SmartZone feature extends communications beyond the reach of a single-trunked site (antenna location) when operating in a SmartZone system. SmartZone units provide expanded wide-area coverage. SmartZone automatically switches the radio to a different site when the current site signal becomes unacceptable. This usually happens when the vehicle in which the radio is located is driven out of the range of one site, and into the range of another. Under normal conditions, a SmartZone-enabled radio functions invisibly to the operator. However, the operator does have some manual controls on the Control Head the RSSI menu entry. This button can be used to check, or change, the SmartZone operation. Using Site Trunking Feature If the zone controller loses communication with any site, that site reverts to site trunking. The display shows the currently selected zone/channel combination and Site trunking. Note: When this occurs, you can communicate only with other radios within your trunking site. Locking and Unlocking a Site This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system. Procedure:

Use the preprogrammed Site Lock/Unlock button to toggle the lock state between locked and unlocked. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Site. 2 Press the Menu Select button directly below Site. 3 Press the Menu Select button directly below Lock to lock the site. OR Press the Menu Select button directly below Unlk to unlock the site. 4 The radio saves the new site lock state and returns to the Home screen. Viewing and Changing a Site This feature allows you to view the number of the current site or force your radio to change to a new one. Viewing the Current Site Procedure:

1 Press the preprogrammed Site Search button. OR

> or < (on the keypad mic.) to RSSI. 2 The display momentarily shows the name of the current site and its corresponding received signal strength indicator

(RSSI). A d v a n c e d F e a t u r e s 91 English Changing the Current Site Procedure:

1 Press and hold down the preprogrammed Site Search button. OR Press and hold down the Menu Select button directly below RSSI. 2 A tone sounds and the display momentarily shows Scanning site. When the radio finds a new site, it returns to the Home screen. s e r u t a e F d e c n a v d A 92 English Trunked Announcement The announcement capability allows you to make announcements to the entire user group, as well as monitor talkgroup calls and other announcements. Announcement calls are handled in two different ways, depending on the trunked central controller configuration. The two types are called ruthless and non-ruthless preemption. Ruthless Preemption:

When a ruthless preemption announcement call is initiated, the requesting radio begins transmitting immediately. All associated talkgroup calls taking place on other channels are immediately halted, and the radios are steered to the announcement call. Transmitting radios continue to transmit until the PTT button is released, at which time they also unmute for the announcement call. Individual calls (Private Conversation and telephone interconnect) are not affected. Non-Ruthless Preemption:

When a non-ruthless preemption announcement is initiated, the initiating unit receives a telephone-type busy tone, followed by a call back when all associated talkgroup conversations end. Once an announcement call is pending, any attempts by other users to initiate a talkgroup call will result in a telephone-type busy tone. These users will not receive a call back until the announcement call is complete. Initiating an Announcement If your radio has been programmed to allow announcement calls:

Procedure:

1 If channel is set as the primary mode, turn the MFK to locate the announcement-group mode. 2 Press the microphone PTT button to initiate the announcement. A d v a n c e d F e a t u r e s Ignition Switch Options This feature allows the user to select the radios functionality based on the Ignition State of the radio users vehicle. The available options are as follows. Blank This option allows the user to power on and power off the radio through the Power button regardless of the Ignitions current state. Tx Inhibit This option allows the user to power on and power off the radio through the Power button regardless of the Ignitions current state. In addition, if the Ignition is not present, then all transmissions are inhibited. This includes receiving any Trunking dispatch communications since the radio will not affiliate with the Trunking systems. PTT Tx Inhibit This option allows the user to power on and power off the radio through the Power button regardless of the Ignitions current state. In addition, if the Ignition is not present, then all PTT button transmissions are inhibited. However, the radio is able to affiliate with the Trunking systems. 93 English Required This option allows the user to power on the radio only if the Ignition is present. The radio can be powered off either through Power button press or when Ignition is lost. In addition, the radio automatically powers on when the Ignition is present only if the radio was turned off due to the ignition being removed. This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires. Soft Power Off This option allows the user to power on the radio either through Power button presses or when the Ignition is detected. Meanwhile, if the Power button was pressed or the Ignition was removed, the radio will be turned off. This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires. Ignition Only Power Up This option allows the user to power on the radio only when Ignition is detected and will power off when it is removed. The radio does not power on or off with the Power button press. s e r u t a e F d e c n a v d A This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires. Note: While "Ignition" is not present, the radio powers-off with a radio-user Power Off button / knob selection if the radio was powered-up with an Emergency Power Up footswitch-press or Ignition Auto Power Off timer is running. While "Ignition" is present, the radio powers-on with a radio-user Power On button / knob selection only if the radio was powered-down with Inactivity Auto Power Off timer. Emergency Power Up This feature allows the user to power on the radio and automatically transmits an emergency mode transmission on personalities with emergency enabled, with the use of a footswitch. In addition, when the Ignition Switch option is set to either Tx Inhibit or PTT Tx Inhibit, this feature will not be available to the users. Press the footswitch to turn on the radio and launch Emergency. A tone sounds and the display shows Emergency. 94 English Auto Power Off Timer Auto Power Off feature powers off the radio when no user actions occur during a preprogrammed length of time. There are two different versions of Auto Power Off:

Inactivity Auto Power Off Timer This timer begins once the radio is power-on. While the timer is active any user interaction with the radio resets the timer. Ignition Auto Power Off Timer This timer begins once the vehicle key is removed, when the voltage at the ignition sense is removed. While the timer is active any user interaction with the radio resets the timer. When the vehicle key is reapplied, the voltage at the ignition is reconnected, this timer is stopped. Although both Inactivity Auto Power Off and Ignition Auto Power Off can be enabled together, Ignition Auto Power Off timer is mutually exclusive with Inactivity Auto Power Off timer when both are enabled. During the last two minutes of the timer countdown, the radio generates continuous low tone and blinks Powering off warning on the display until the timer expires or the timer is reset. The radio automatically powers off after the timer expires. The duration of the timer is preprogrammed. Utilities A d v a n c e d F e a t u r e s Viewing Recent Calls List This feature allows you to view the recent incoming and outgoing call information of the following call types:

Call Alert Selective Call Private Call Phone Call (Outgoing only) Note:

The radio can also be preprogrammed to log the radio IDs associated with incoming Dispatch Calls. Check with your dealer or system administrator for more information. Procedure:

1 > or < (on the keypad mic.) to Rcnt. 2 Press the Menu Select button directly below Rcnt to access the Recent Calls feature screen. 3 D or U to scroll through the list. 4 Press the Menu Select button directly below Back to return to Home screen. OR Press H or the PTT button to return to the Home screen. 95 English If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. 3 The display shows Low power and the low power icon. OR The display shows High power and the high power icon. Selecting the Power Level You can select the power level at which your radio transmits. The radio always turns on to the default setting. Note:

This feature must be preprogrammed by a qualified radio technician. Settings:

Select Low for a shorter transmitting distance and to conserve power. Select High for a longer transmitting distance. Procedure:

Use the preprogrammed Transmit Power Level Switch to toggle transmit power level between high and low. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Pwr. 2 Press the Menu Select button directly below Pwr. s e r u t a e F d e c n a v d A 96 English Selecting a Radio Profile This feature allows you to manually switch the visual and audio settings of the radio. The display, backlight, alert tones, and audio settings are defined according to the preprogrammed radio settings of each radio profile. Please refer to a qualified technician for more information. Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure:

Use the preprogrammed Profile button and proceed to Step 3. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Prfl. 2 Press the Menu Select button directly below Prfl to access the Profiles feature screen. 3 D or U to scroll through the menu selections. 4 Press the Menu Select button directly below Sel to select the required radio profile. OR Press the Menu Select button directly below Exit to exit the screen without making any changes. 5 The radio returns to the Home screen. The profile name on the Home screen indicates the current selected radio profile. Controlling the Display Backlight You can enable or disable the radios display backlight as needed, if poor light conditions make the display difficult to read. Depending on how your radio is preprogrammed, you can also maintain a minimum backlight level on the radios display. Procedure:

Note: Press the Dimmer button to adjust the brightness of the display. Long press to toggle between day and night mode. Turning Keypad Tones On or Off You can enable and disable keypad tones as needed. Procedure:

Press the preprogrammed Keypad Mute button to turn the tones on or off. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Mute. 2 Press the Menu Select button directly below Mute. 3 The display momentarily shows Tones off, indicating that the keypad tones are disabled. OR The display momentarily shows Tones on, and a short tone sounds, indicating that the keypad tones are enabled. A d v a n c e d F e a t u r e s 97 English Turning Voice Mute On or Off You can enable and disable voice muting of the affiliated trunking talkgroup or selected conventional channel as needed. Procedure:

Press the preprogrammed Voice Mute button to turn the feature on or off. OR Follow the procedure below. 1 > or < (on the keypad mic.) to VMut. 2 Press the Menu Select button directly below VMut. 3 The display momentarily shows Voice mute off, and a short tone sounds, indicating that the feature is disabled. OR The display momentarily shows Voice mute on, and a short tone sounds, indicating that the feature is enabled. s e r u t a e F d e c n a v d A 98 English Using the Time-Out Timer This feature turns off your radios transmitter. You cannot transmit longer than the preset timer setting. If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone. The timer is defaulted at 60 seconds, but it can be preprogrammed from 3 to 120 seconds, in 15-second intervals, or it can be disabled entirely for each radio mode, by a qualified radio technician. Note: You will hear a brief, low-pitched, warning tone four seconds before the transmission times out. Procedure:

1 Hold down the PTT button longer than the preprogrammed time. You hear a short, low-pitched warning tone, the transmission is cut-off, and the LEDs goes out until you release the PTT button. 2 Release the PTT button. The LEDs relight and the timer resets. 3 Press the PTT button to re-transmit. The time-out timer restarts and the red LED lights up. Using the Conventional Squelch Operation Features This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise. 1 Procedure:

> or < (on the keypad mic.) to Sql. 2 Press the Menu Select button directly below Sql. The display shows Squelch XX, where XX is the value for the current squelch. 3 Press the Menu Select button directly below + to increase the squelch volume. OR Press the Menu Select button directly below - to decrease the squelch volume. 4 Press H to return to the selected channel. Analog Options Tone Private Line (PL), Digital Private-Line (DPL), and carrier squelch can be available (preprogrammed) per channel. Option Result Carrier squelch (C) You hear all traffic on a channel. The radio responds only to your messages. PL or DPL Digital Options One or more of the following options may be preprogrammed in your radio. Consult your dealer or system administrator for more information. A d v a n c e d F e a t u r e s Result Option Digital You hear any digital traffic. Carrier-Operated Squelch (COS) Normal Squelch You hear any digital traffic having the correct network access code. Selective Switch You hear any digital traffic having the correct network access code and correct talkgroup. 99 English Using the PL Defeat Feature This feature allows you to override any coded squelch (DPL or PL) that might be preprogrammed to a channel. The radio also unmutes to any digital activity on a digital channel. Procedure:

Place the preprogrammed PL Defeat switch in the PL Defeat position. You hear any activity on the channel. OR The radio is muted if no activity is present. Note: When this feature is active, the Carrier Squelch status indicator is displayed. Using the Digital PTT ID Feature This feature allows you to the radio ID (number) of the radio from whom you are currently receiving a transmission. This ID, consisting up to a maximum of eight characters, can be viewed by both the receiving radio and the dispatcher. Your radios ID number is also automatically sent every time the PTT button is pressed. This is a per-channel feature. For digital voice transmissions, your radios ID is sent continuously during the voice message. s e r u t a e F d e c n a v d A 100 English Using the Smart PTT Feature (Conventional Only) Smart PTT is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations. When smart PTT is enabled in your radio, you cannot transmit on an active channel. If you try to transmit on an active smart-PTT channel, you hear an alert tone, and the transmission is inhibited. The LED lights up solid yellow to indicate that the channel is busy. Three variations of smart PTT are available:

Mode Transmit Inhibit on Busy Channel with Carrier Transmit Inhibit on Busy Channel with Wrong Squelch Code Description You cannot transmit if any traffic is detected on the channel. You cannot transmit on an active channel with a squelch code or (if secure-

equipped) encryption key other than your own. If the PL code is the same as yours, the transmission is not prevented. Quick-Key Override This feature can work in conjunction with either of the two above variations. You can override the transmit-inhibit state by quick-keying the radio. In other words, two PTT button presses within the preprogrammed time limit. Accessing General Radio Information Your radio contains information on the following:

Radio Information IP Display Control Assignments Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Accessing Radio Information This feature displays the following information of your radio:

Host Version Secure Version CH 1 4 Version

(depending on the number of channels connected.) TIB Version TRC Version URC Version DSP Version KG (Secure Algorithm) Serial Number MCHIB Version CHIB Version AUX CH Version Siren Version VRS Version DVRS App Version (only when DVRS is available) DVRS DSP Version (only when DVRS is available) DVRS CP Version (only when DVRS is available) Model Number ESN Flash Code Tuning Version Serial Number Flash Size & Type RF Band Processor Version Note: Press H at any time to return to the Home screen. Procedure:

1 > or < (on the keypad mic.) to Info. 2 Press the Menu Select button directly below Info. 3 U or D to Radio info and press the Menu Select button directly below Sel. 4 The display shows the Information screen. 5 D or U to scroll through the various information. OR Press the Menu Select button directly below Back to return to previous screen. OR Press H to exit and return to the home display. A d v a n c e d F e a t u r e s 101 English Viewing Control Assignments This feature displays the programmable radio functions assigned to the controls of your radio for the currently selected channel. See Programmable Features on page 7 for more information on the various programmable features of your radio. Procedure:

1 > or < (on the keypad mic.) to Info. 2 Press the Menu Select button directly below Info. 3 D or U to Control map and press the Menu Select button directly below Sel. 4 D or U to scroll through the various information. OR Press the Menu Select button directly below Back to return to previous screen. OR Press H to exit and return to the Home display. Viewing IP Information This feature displays the device name, IP address, and status of your radio. Note:

The device name of your radio is preprogrammed. Check with your dealer or system administrator for more information. Procedure:

Press the preprogrammed Info button and proceed to Step 3. OR Follow the procedure below. 1 > or < (on the keypad mic.) to Info. 2 Press the Menu Select button directly below Info. 3 D or U to Ip info and press the Menu Select button directly below Sel. 4 D or U to scroll through the various information. OR Press the Menu Select button directly below Back to return to previous screen. OR Press H to exit and return to the Home display. s e r u t a e F d e c n a v d A 102 English Using Siren, PA and Light Your radio supports siren and light via the keypad microphone. The keypad microphone can be preprogrammed to enable siren, public address and light. Using Keypad as Siren Type Selector The keypad can be preprogrammed as different types of siren. Each button can be preprogrammed as a different siren tone. For example, pressing the preprogrammed button turns on the siren. Procedure:

1 Press the preprogrammed siren button to turn on the siren. The display shows Siren on. 2 Press a different preprogrammed siren button to change the siren tone. OR Press the same preprogrammed button to turn off the siren. A d v a n c e d F e a t u r e s Using Keypad as Light Type Selector The keypad can be preprogrammed as different types of light. Each button can be preprogrammed as a different light. For example, pressing the preprogrammed button turns on the light. Procedure:

1 Press the preprogrammed light button to turn on the light. 2 Press a different preprogrammed light button to change the light. OR Press the same preprogrammed button to turn off the light. Using the Public Address Button on the Keypad The keypad can be preprogrammed to enable the radios internal public address (PA) system. Procedure:

1 Press the preprogrammed public address button to turn on the public address feature. The display shows PA on. 2 Press the preprogrammed public address button to turn off the public address feature. When the internal public address and siren feature are turned on at the same time, the display shows Siren/PA on. 103 English Using Optional External Alarms (Horn and Lights) All control heads can be equipped for external alarms (horn and lights) that are activated when a Call Alert page, Private Conversation call, or phone call is received. The radio always powers up with the horn and lights feature enabled. Note:

The horn and lights feature must be enabled by a qualified radio technician. Using Non-Permanent Horn and Lights Procedure:

1 Press the Menu Select button directly below H/L momentarily. The last selected alarm(s) are enabled, and the display shows the enabled alarm(s) alternating with the selected mode, until it is turned off. 2 Press the Menu Select button directly below H/L momentarily to turn off the alarm(s). The display shows Horn/Lites off. Using the External Public Address Button on the Keypad The keypad can be preprogrammed to enable the radios external public address (PA) system. This button enables the external speaker to be able to transmit the radio user announcement publicly. Procedure:

1 Press the preprogrammed public address button to turn on the public address feature. The display shows Ext Rad on. 2 Press the preprogrammed public address button to turn off the public address feature. When the external public address and internal public address feature is turned on at the same time, the display shows Ext Rad/PA on. s e r u t a e F d e c n a v d A 104 English Using Permanent Horn and Lights If Permanent Horn and Lights is enabled, horn and lights will automatically be turned on when the radio powers up. Procedure:

1 Press the Menu Select button directly below H/L once to turn off the alarm(s). 2 Press the Menu Select button directly below H/L momentarily to enable the last selected alarm(s). The display briefly shows the enabled alarms, and then reverts back to the selected mode. Changing the Selected Alarms Procedure:

1 Press the Menu Select button directly below H/L until the display shows the required alarm. 2 Press the Menu Select button directly below the required entry and the display exits to Home screen. Press the Menu Select button directly below the entry activates the option. Below are the selections available. Select H+L to turn on both horn and lights. The display shows Horn/Lites on. Select Lgts to turn on the lights. The display shows Lights on. Select Horn to turn on the horn. The display shows Horn on. An Off entry is shown at the softkey when one of the features above is active. Selecting the Off deactivates the current active alarm. A d v a n c e d F e a t u r e s 105 English Receiving a Call While Alarms are Turned On When you receive a call with the Alarms turned on:

Procedure:

1 You hear the vehicles horn sounds for four seconds, and/or the car lights turn on for 60 seconds. 2 The display shows the type of call received (Call, Page, or Phone) and the selected mode name. The time interval can be modified by a qualified radio technician. Turning Off Non-Rearmable External Alarms Procedure:

1 Press the Menu Select button directly below Call, Page or Phon will turn off the external alarm(s) and place you directly in that feature. OR Press the PTT button or any control-head button to turn off the external alarm(s). 2 Press the Menu Select button directly below H/L momentarily to rearm the horn and lights feature. The Volume Knob and the Dimmer button have no effect on the state of the external alarm(s). s e r u t a e F d e c n a v d A 106 English Turning Off Rearmable External Alarms Procedure:

1 Press the Menu Select button directly below Call, Page or Phon to turn off the external alarm(s) and place you directly in that feature. The external alarm(s) is turned off and automatically rearmed so that when you exit the entry, the external alarm(s) will automatically turn on. OR Press the PTT button or any control head button other than the Menu Select button directly below H/L to turn off the external alarm(s). The external alarm(s) is turned off and automatically rearmed so that when you exit the entry, the external alarm(s) will automatically turn on. OR Press the Menu Select button directly below H/L to turn off the external alarm(s) and exit the Horn and Lights feature. Press the Menu Select button directly below H/L momentarily to rearm the horn and lights feature. The Volume knob and the Dimmer button have no effect on the state of the external alarms. Using the Voice Announcement This feature enables the radio to audibly indicate the current feature mode, Zone or Channel the user has just assigned. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display. Each voice announcement is within a limit of three seconds maximum. The sum total duration for all voice announcements in a radio shall be no more than 1000 seconds. Note:

This feature must be preprogrammed by a qualified radio technician. The features which Voice Announcement supports are:

Zone Scan Talkaround/Direct Emergency On Secure/Clear Channel Monitor (Conventional) Tx Inhibit In-Call User Alert (Voice Mute) Multi Functional Button Note: Voice announcements support certain number of zone-channel, but not all. Seek advice from your dealer or qualified technician for the best selections for this feature. The two options of priority for the Voice Announcement available are:

High enables the voice of the feature to announce even when the radio is receiving calls. Low disables the voice of the feature from announcing when the radio is receiving calls. Procedure:

You hear a voice announcement when the features below are preprogrammed in the radio. The radio powers up. The radio announces the current zone and channel it is transmitting. Press the preprogrammed voice announcement button

(which specifically programmed to playback the current zone and channel). The radio announces the current zone and channel it is transmitting. Note: Pressing this preprogrammed playback button will always enable the voice feature to announce in High priority. All the three programmable buttons at the side of the radio support this feature. A d v a n c e d F e a t u r e s 107 English Change to a new zone. The radio announces the current zone and channel it is transmitting. Change to a new channel within the current zone. The radio announces the current channel. Press either the Menu Select button or preprogrammed button of the radio to launch or terminate Scan, Monitor, Talkaround/Direct or Transmit Inhibit. The radio announces the corresponding feature activation or deactivation. s e r u t a e F d e c n a v d A 108 English Helpful Tips The following are suggestions to assist you in troubleshooting possible operating problems.

!

+ = K J E  

The cables that connect to the rear of the radio could have live voltage on some of their pins. Do not remove or reconnect these cables. Only a qualified radio technician should perform this task. Service performed by unauthorized personnel may cause the radio to transmit an emergency alarm even if the unit is turned off. If your radio is locked up or the display shows FAIL 01/09, turn the radio off and then back on. If this does not correct the condition, take the radio to a qualified radio technician for service. If radio operation is intermittent, check with other persons using the system for similar problems before taking the radio in for service. Similar problems indicate a system malfunction rather than a radio failure. If symptoms persist or, if your unit exhibits other problems, contact a qualified radio technician. Accessories For a list of Motorola-approved antennas and other accessories, visit the following website:

http://www.motorolasolutions.com/APX On the website, search for APX Mobile Radios. You will see the accessories information besides the specifications of the radio. You can also contact your dealer for details. A c c e s s o r i e s 109 English F H V e h t n i i e s U o d a R e m i t i r a M i

:

x d n e p p A Appendix: Maritime Radio Use in the VHF Frequency Range Take a moment to review the following:

Special Channel Assignments. page 110 Operating Frequency Requirements. page 111 Declaration of Compliance for the Use of Distress and Safety Frequencies . page 113 Technical Parameters for Interfacing External Data Sources . page 113 Special Channel Assignments Emergency Channel If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order:

1 MAYDAY, MAYDAY, MAYDAY. 2 THIS IS _____________________, CALL SIGN __________. State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times. 110 English 3 Repeat MAYDAY and the name of the vessel. 4 WE ARE LOCATED AT _______________________. State the position of the vessel in distress, using any information that will help responders to locate you, e.g.:

latitude and longitude bearing (state whether you are using true or magnetic north) distance to a well-known landmark vessel course, speed or destination 5 State the nature of the distress. 6 Specify what kind of assistance you need. 7 State the number of persons on board and the number needing medical attention, if any. 8 Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc. 9 OVER. 10 Wait for a response. 11 If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you. Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast Guard. Non-Commercial Call Channel For non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9. Operating Frequency Requirements Channel Number A radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows:

on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency on ships subject to the Safety Convention, the radio must be capable of operating:

a. in the simplex mode on the ship station transmitting frequencies specified in the 156.025 157.425 MHz frequency band, and in the semiduplex mode on the two frequency channels specified in the table below. b. Note: Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. 1 2

*

4 5 6 7 8 9 10 11 12 13**

14 15**

16 17**

18 19 Table A-1: VHF Marine Channel List Frequency (MHz) Transmit 156.050 156.100 156.150 156.200 156.250 156.300 156.350 156.400 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 156.850 156.900 156.950 Receive 160.650 160.700 160.750 160.800 160.850 160.950 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 156.850 161.500 161.550 A p p e n d x

:

i M a r i t i m e R a d o U s e i i n t h e V H F 111 English Table A-1: VHF Marine Channel List (Continued) Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Transmit 157.000 157.050 157.100 157.150 157.200 157.250 157.300 157.350 157.400 156.025 156.075 156.125 156.175 156.225 156.275 156.325 156.375 156.425 156.475 156.575 156.625 156.675 Receive 161.600 161.650 161.700 161.750 161.800 161.850 161.900 161.950 162.000 160.625 160.675 160.725 160.775 160.825 160.875 160.925 156.375 156.425 156.475 156.575 156.675 Channel Number 74 75 76 77**

78 79 80

*

*

*

84 85 86 87 88 Frequency (MHz) Transmit 156.725

***

***

156.875 156.925 156.975 157.025 157.075 157.125 157.175 157.225 157.275 157.325 157.375 157.425 Receive 156.725

***

***

161.525 161.575 161.625 161.675 161.725 161.775 161.825 161.875 161.925 161.975 162.025

* Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.

** Low power (1 W) only

*** Guard band Note: A in the Receive column indicates that the channel is transmit only. F H V e h t n i i e s U o d a R e m i t i r a M i

:

x d n e p p A Channel Number 20

*

22

*

24 25 26 27 28 60

*

62 63

*

65 66 67**

68 69 71 72 73 112 English Declaration of Compliance for the Use of Distress and Safety Frequencies The radio equipment does not employ a modulation other than the internationally adopted modulation for maritime use when it operates on the distress and safety frequencies specified in RSS-182 Section 7.3. Technical Parameters for Interfacing External Data Sources Input Voltage (Volts Peak-to-peak) Max Data Rate Impedance RS232 18V 28 kb/s 5k ohm USB 3.6V 12 Mb/s 90 ohm SB9600 5V 9.6 kb/s 120 ohm A p p e n d x

:

i M a r i t i m e R a d o U s e i i n t h e V H F 113 English Glossary This glossary is a list of specialized terms used in this manual. Term Definition ACK Active Channel A channel that has traffic on it. Acknowledgment of communication. Analog Signal ARS ASTRO 25 Trunking ASTRO Conventional Autoscan AUX CH Call Alert An RF signal that has a continuous nature rather than a pulsed or discrete nature. Automatic Registration Service Motorola standard for wireless digital trunked communications. Motorola standard for wireless digital conventional communications. A feature that allows the radio to automatically scan the members of a scan list. Auxiliary Control Head Privately page an individual by sending an audible tone. y r a s s o G l 114 English Term Definition Feature that responds to the presence of an RF carrier by opening or unmuting

(turning on) a receivers audio circuit. A squelch circuit silences the radio when no signal is being received so that the user does not have to listen to noise. A software-controlled, computer-driven device that receives and generates data for the trunked radios assigned to it. It monitors and directs the operations of the trunked repeaters. A group of characteristics such as transmit/

receive frequency pairs, radio parameters, and encryption encoding. Control Head Interface Board In a trunking system, one of the channels that is used to provide a continuous, two-

way/data communications path between the central controller and all radios on the system. Typically refers to radio-to-radio communications, sometimes through a repeater (see Trunking). A scan list that includes only conventional channels. Carrier Squelch Central Controller Channel CHIB Control Channel Conventional Conventional Scan List Term CP Cursor Deadlock Digital Private Line (DPL) Digital Signal Dispatcher DSP DVRS Dynamic Regrouping ESN Definition Term Definition Codeplug A visual tracking marker (a blinking line) that indicates a location on the display. Displayed by the radio after three failed attempts to unlock the radio.The radio must be powered off and on prior to another attempt. A type of coded squelch using data bursts. Similar to PL except a digital code is used instead of a tone. An RF signal that has a pulsed, or discrete, nature, rather than a continuous nature. An individual who has radio system management duties. Digital Signal Processing Digital Vehicular Repeater System A feature that allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. Electrical Serial Number l G o s s a r y A feature that allows communications to take place even though the central controller has failed. Each trunked repeater in the system transmits a data word informing every radio that the system has gone into failsoft. Federal Communications Commission. Frequency Modulation Disconnect. The first display information after the radio completes its self test. Key-variable loader: A device for loading encryption keys into the radio. Liquid crystal display Light-emitting diode A software-activated feature shown at the bottom of the display selection of these features is controlled by the g. Millennium Control Head Board Failsoft FCC FM Hang Up Home screen KVL LCD LED Menu Entry MCHB 115 English Term Definition Monitor Multi-System Talkgroup Scan List Network Access Code Non-Tactical/

Revert OTAR Page Check channel activity through menu entries. If the channel is clear, you hear static. If the channel is in use, you hear conversation. It also serves as a way to check the volume level of the radio, since the radio opens the squelch when the monitor button is pressed. A scan list that can include both talkgroups

(trunked) and channels (conventional). Network Access Code (NAC) operates on digital channels to reduce voice channel interference between adjacent systems and sites. The user talks on a preprogrammed emergency channel. The emergency alarm is sent out on this same channel. Over-the-air rekeying. A one-way alert, with audio and/or display messages. A set of unique features specific to a radio. Personal Identification Number Personality PIN Preprogrammed Refers to a software feature that has been activated by a qualified radio technician. y r a s s o G l 116 English Term Private

(Conversation) Call Private Line

(PL) Programmable PTT Radio Frequency (RF) Repeater Selective Call Definition A feature that lets you have a private conversation with another radio user in the talkgroup. A sub-audible tone that is transmitted such that only receivers decoding the tone receives it. Refers to a radio control that can have a radio feature assigned to it. Push-To-Talk the PTT button engages the transmitter and puts the radio in transmit (send) operation when pressed. The part of the general frequency spectrum between the audio and infrared light regions (about 10 kHz to 10,000,000 MHz). A conventional radio feature, where you talk through a receive/transmit facility that re-transmits received signals, in order to improve communications range and coverage. A feature that allows you to call a select individual, intended to provide privacy and to eliminate the annoyance of having to listen to conversations of no interest to you. Term Definition Selective Switch Squelch Standby Status Calls Tactical/

Non-Revert Talkaround Talkgroup TMS Any digital P25 traffic having the correct Network Access Code and the correct talkgroup. Special electronic circuitry, added to the receiver of a radio, that reduces, or cuts off, unwanted signals before they are heard in the speaker. An operating condition whereby the radios speaker is muted but still continues to receive data. Pre-defined text messages that allow the user to send a conditional message without talking. The user talks on the channel that was selected before the radio entered the emergency state. Bypass a repeater and talk directly to another unit for easy local unit-to-unit communications. An organization or group of radio users who communicate with each other using the same communication path. Text Messaging Service Term Trunking Trunking Priority Monitor Scan List USK UTC VRS Zone l G o s s a r y Definition The automatic sharing of communications paths between a large number of users

(see Conventional). A scan list that includes talkgroups that are all from the same trunking system. Unique Shadow Key Coordinated Universal Time. The international time standard (formerly Greenwich Mean Time, or GMT). Zero hours UTC is midnight in Greenwich, England, which is located at 0 degrees longitude. Everything east of Greenwich

(up to 180 degrees) is later in time;

everything west is earlier. There are 42 time authorities around the world that are constantly synchronizing with each other. Abbreviated as UTC (English backronym =

Universal Time, Coordinated), it is also known as Zulu (Z) Time. Vehicular Repeater System A grouping of channels. 117 English Commercial Warranty and Service Limited Warranty MOTOROLA COMMUNICATION PRODUCTS I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:

MOTOROLA SOLUTIONS INC. (MOTOROLA) warrants the MOTOROLA manufactured Communication Products listed below

(Product) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:

APX Mobile Radio Product Accessories One (1) Year One (1) Year MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA. This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the e c i v r e S d n a y t n a r r a W l a i c r e m m o C 118 English Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product. MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. II. GENERAL PROVISIONS:

This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLAs option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. C)Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. III. STATE LAW RIGHTS:

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. IV. HOW TO GET WARRANTY SERVICE:

You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at 1-800-927-2744 US/Canada. V. WHAT THIS WARRANTY DOES NOT COVER:

A) Defects or damage resulting from use of the Product in other than its normal and customary manner. B) Defects or damage from misuse, accident, water, or neglect. D)Breakage or damage to antennas unless caused directly by defects in material workmanship. E) A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim. F) Product which has had the serial number removed or made illegible. G)Rechargeable batteries if:

any of the seals on the battery enclosure of cells are broken or show evidence of tampering. the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified. H)Freight costs to the repair depot. I) A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLAs published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA. J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. K) Normal and customary wear and tear. C o m m e r c i a l W a r r a n t y a n d S e r v i c e 119 English VI. PATENT AND SOFTWARE PROVISIONS:

MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:

A) that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;

B) that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and C)should the Product or parts become, or in MOTOROLAs opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA. MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights. VII. GOVERNING LAW:

This Warranty is governed by the laws of the State of Illinois, U.S.A. e c i v r e S d n a y t n a r r a W l a i c r e m m o C 120 English VIII. FOR AUSTRALIA ONLY:

This warranty is given by Motorola Solutions Australia Pty Limited

(ABN 16 004 742 312) of Tally Ho Business Park, 10 Wesley Court. Burwood East, Victoria. Our goods come with guarantees that cannot be excluded under the Australia Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Motorola Solutions Australias limited warranty below is in addition to any rights and remedies you may have under the Australian Consumer Law. If you have any queries, please call Motorola Solutions Australia at 1800 457 439. You may also visit our website:

http://www.motorola.com/Business/XA-EN/Pages/

Contact_Us#support_tab for the most updated warranty terms. SERVICE Proper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola to support maintenance services. Through its maintenance and installation program, Motorola makes available the finest service to those desiring reliable, continuous communications on a contract basis. For a contract service agreement, please contact your nearest Motorola service or sales representative, or an authorized Motorola dealer. Express Service Plus (ESP) is an optional extended service coverage plan, which provides for the repair of this product for a period of three years from the date of shipment from the factory, or the date of delivery if purchased from an authorized Motorola two-

way radio dealer. For more information about ESP, contact the Motorola Radio Support Center, 2204 Galvin Drive, Elgin, IL 60123, 1-800-227-6772. C o m m e r c i a l W a r r a n t y a n d S e r v i c e 121 English Notes e c i v r e S d n a y t n a r r a W l a i c r e m m o C 122 English Motorola Solutions, Inc. 1303 East Algonquin Road Schaumburg, Illinois 60196 U.S.A. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. 2012, 2013 Motorola Solutions, Inc. All rights reserved. June 2013.

*68012006035*

68012006035-C

 

 

6881095C99_SafetyM_Eng.fm Page 1 Tuesday, March 20, 2012 2:43 PM RF Energy Exposure and Product Safety Guide for Mobile Two-Way Radios Installed in Vehicles, Vessels or as Fixed Site Control Stations ATTENTION!

BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. The information provided in this document supersedes the general safety information contained in user guides published prior to January 2008. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. 2005 2012 Motorola Solutions, Inc. All rights reserved. Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, U.S.A.

*NNTN7851D*

NNTN7851D

*6881095C99*

6881095C99-J English 6881095C99_SafetyM_Eng.fm Page 2 Tuesday, March 20, 2012 2:43 PM RF Energy Exposure Awareness and Control Information, and Operational Instructions for FCC Occupational Use Requirements NOTICE: This radio is intended for use in occupational/controlled conditions, where users have full knowledge of their exposure and can exercise control over their exposure to meet FCC limits. This radio device is NOT authorized for general population, consumer, or any other use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. English 2 6881095C99_SafetyM_Eng.fm Page 3 Tuesday, March 20, 2012 2:43 PM Please refer to the following Web sites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits. http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Federal Communication Commission Regulations The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for mobile two-way radios before they can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a label directing users to specific user awareness information. Your Motorola two-way radio has a RF exposure product label. Also, your Motorola user manual, or separate safety booklet, includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standard Your Motorola two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE and ICNIRP exposure limits for occupational/

controlled RF exposure environment at duty factors of up to 50% talk-50%

listen and is authorized by the FCC for occupational use only. In terms of measuring RF energy for compliance with the FCC exposure guidelines, your radio antenna radiates measurable RF energy only while it is transmitting

(during talking), not when it is receiving (listening) or in standby mode. 3 English 6881095C99_SafetyM_Eng.fm Page 4 Tuesday, March 20, 2012 2:43 PM Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:

United States Federal Communications Commission (FCC), Code of Federal Regulations; 47 CFR et seq. FCC, OET Bulletin 65 Institute of Electrical and Electronic Engineers (IEEE) C95.1 International Commission on Non-Ionizing Radiation Protection (ICNIRP) Ministry of Health (Canada) Safety Code 6 Industry Canada RSS-102 Australian Communications Authority Radiocommunications Standard et seq. ANATEL ANNEX to Resolution No. 303 et seq. RF Exposure Compliance and Control Guidelines and Operating Instructions To control exposure to yourself and others and to ensure compliance with the RF exposure limits, always adhere to the following procedures. Guidelines:

User awareness instructions should accompany device when transferred to other users. DO NOT use this device if the operational requirements described herein are not met. English 4 6881095C99_SafetyM_Eng.fm Page 5 Tuesday, March 20, 2012 2:43 PM Instructions:

Transmit no more than the rated duty factor of 50% of the time. To transmit

(talk), push the Push-To-Talk (PTT) button or, for radios equipped with VOX, speak into the microphone. The red LED will illuminate when the radio is transmitting. To receive calls, release the PTT button, or, for radios equipped with VOX, stop talking. The red LED will extinguish when the radio stops transmitting. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away, as shown in Table 1, from the body of a vehicle with a properly installed antenna. This separation distance will ensure that there is sufficient distance from a properly installed

(according to installation instructions) externally-mounted antenna to satisfy the RF exposure requirements in the standards listed above. NOTE: Table 1 below lists the recommended lateral distance for people in an uncontrolled environment from the body of a vehicle with an approved, properly installed transmitting antenna (i.e., monopoles over a ground plane, or dipoles) at several different ranges of rated radio power for mobile radios installed in a vehicle. Table 1. Rated Power of Vehicle-Installed Mobile Two-Way Radio and Recommended Minimum Lateral Distance from Vehicle Body Mobile Radio Rated Power (see Note) Less than 7 watts 7 to 14 watts 15 to 39 watts 40 to 110 watts Minimum Lateral Distance from Vehicle Body 8 inches (20 centimeters) 1 foot (30 centimeters) 2 feet (60 centimeters) 3 feet (90 centimeters) 5 English 6881095C99_SafetyM_Eng.fm Page 6 Tuesday, March 20, 2012 2:43 PM When a mobile radio is used in conjunction with another co-located transmitter such as a Vehicular Repeater, it is the vehicle operators responsibility to take appropriate steps to keep bystanders at the required separation distance from the vehicle to ensure compliance with the FCC's RF energy exposure limits for the general population. See the co-located transmitters user manual for more details. NOTE: If you are not sure of the rated power of your radio, contact your Motorola representative or dealer and supply the radio model number found on the radio model label. If you can not determine the rated power out, then assure 3-feet separation from the body of the vehicle. Users of multi-band radios subject to different separation distances in different operating bands according to Table 1 should select the larger applicable distance as the minimum lateral distance for bystanders outside the vehicle. The maximum power shown on the FCC Grant may be higher than the rated power allowing for production variation. Mobile Antenna Installation Guidelines These mobile antenna installation guidelines are limited to metal body motor vehicles or vehicles with appropriate ground planes. Antennas should be installed in the center area of the roof or the trunk lid taking into account exposure conditions of backseat passengers and according to the specific instructions and restrictions in the Radio Installation Manual along with the requirements of the antenna supplier. Trunk lid installations are limited to vehicles with clearly defined flat trunk lids, and in some cases, to specific radio models and antennas. See the Radio Installation Manual for specific information on how and where to install specific types of approved antennas to facilitate recommended operating distances to all potentially exposed persons. Use only the Motorola-approved, supplied antenna or a Motorola-

approved replacement antenna. Unauthorized antennas, modifications, or English 6 6881095C99_SafetyM_Eng.fm Page 7 Tuesday, March 20, 2012 2:43 PM attachments could damage the radio and may result in non-compliance with RF Safety Standards. Approved Accessories This radio has been tested and meets RF Safety Standards when used with the Motorola accessories supplied or designated for this product. Use of other accessories may result in non-compliance with RF Safety Standards. For a list of Motorola-approved antennas and accessories, refer to the user manual for your radio model. Additional Information For additional information on exposure requirements or other training information, visit: http://responsibility.motorolasolutions.com/index.php/

ourapproach/wirelesscommhealth/. Compliance and Control Guidelines and Operating Instructions for Mobile Two-Way Radios Installed as Fixed Site Control Stations If mobile radio equipment is installed at a fixed location and operated as a control station or as a fixed unit, the antenna installation must comply with the following requirements in order to ensure optimal performance and compliance with the RF energy exposure limits in the standards and guidelines listed on page 4:

The antenna should be mounted outside the building on the roof or a tower if at all possible. As with all fixed site antenna installations, it is the responsibility of the licensee to manage the site in accordance with applicable regulatory requirements and may require additional compliance actions such as site survey measurements, signage, and site access restrictions in order to ensure that exposure limits are not exceeded. 7 English 6881095C99_SafetyM_Eng.fm Page 8 Tuesday, March 20, 2012 2:43 PM For additional installation information, see the guidelines for minimum separation distances provided above in the RF Exposure Compliance and Control Guidelines and Operating Instructions section of this document. Compliance and Control Guidelines and Operating Instructions for Mobile Two-Way Radios Installed on Maritime Vessels If mobile radio equipment is installed on a vessel and operated as a fixed unit, the antenna installation must comply with the following requirements in order to ensure optimal performance and compliance with RF energy exposure limits in the standards and guidelines listed on page 4:

An antenna intended for Maritime operation should be chosen and installed according to the manufacturers recommendations. The antennas should be mounted solidly to the vessel structure at the highest location possible. As with all radio antenna installations, it is the responsibility of the operator to maintain adequate distances from the antenna and all personnel on board the vessel or adjacent to the vessel. For additional installation information, see the guidelines for minimum separation distances proved above in the RF Exposure Compliance and Control Guidelines and Operating Instructions section of this document. Electromagnetic Interference/Compatibility NOTE: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. It may be necessary to conduct compatibility testing to determine if any electronic equipment used in or around vehicles or near fixed site antenna is sensitive to external RF energy or if any procedures need to be followed to eliminate or mitigate the potential for interaction between the radio transmitter and the equipment or device. English 8 6881095C99_SafetyM_Eng.fm Page 9 Tuesday, March 20, 2012 2:43 PM Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Vehicles To avoid possible interaction between the radio transmitter and any vehicle electronic control modules, such as ABS, engine, or transmission controls, the radio should be installed only by an experienced installer and the following precautions should be used when installing the radio:

1. Refer to the manufacturers instructions or other technical bulletins for recommendations on radio installation. 2. Before installing the radio, determine the location of the electronic control modules and their harnesses in the vehicle. 3. Route all radio wiring, including the antenna transmission line, as far away as possible from the electronic control units and associated wiring. Driver Safety Check the laws and regulations on the use of radios in the area where you drive. Always obey them. When using your radio while driving, please:

Give full attention to driving and to the road. Pull off the road and park before making or answering a call if driving conditions so require. 9 English 6881095C99_SafetyM_Eng.fm Page 10 Tuesday, March 20, 2012 2:43 PM Acoustic Safety Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the radio's volume, the less time is required before your hearing could be affected. Hearing damage from loud noise is sometimes undetectable at first and can have a cumulative effect. To protect your hearing:

Use the lowest volume necessary to do your job. Turn up the volume only if you are in noisy surroundings. Turn down the volume before adding headset or earpiece. Limit the amount of time you use headsets or earpieces at high volume. When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear. English 10 6881095C99_SafetyM_Eng.fm Page 11 Tuesday, March 20, 2012 2:43 PM Operational Warnings W A R N I N G For Vehicles with an Air Bag DO NOT mount or place a mobile radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. Potentially Explosive Atmospheres Turn off your radio prior to entering any area with a potentially explosive atmosphere. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. The areas with potentially explosive atmospheres include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often, but not always, posted. Blasting Caps and Blasting Areas To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: Turn off two-way radio. Obey all signs and instructions. For radios installed in vehicles fueled by liquefied petroleum gas, refer to the (U.S.) National Fire Protection Association standard, NFPA 58, for storage, handling, and/or container information. For a copy of the LP-gas standard, NFPA 58, contact the National Fire Protection Association, One Battery Park, Quincy, MA. 11 English 6881095C99_SafetyM_Eng.fm Page 12 Tuesday, March 20, 2012 2:43 PM English 12 6881095C99_SafetyM_LAS.fm Page 1 Tuesday, March 20, 2012 2:39 PM Folleto de normas de seguridad y de exposicin a la energa de RF al usar radios bidireccionales mviles instalados en vehculos, embarcaciones o estaciones de control en emplazamientos fijos ATENCIN ANTES DE USAR EL RADIO LEA ESTE FOLLETO, EL CUAL CONTIENE INSTRUCCIONES DE OPERACIN IMPORTANTES PARA SU USO SEGURO, AS COMO INFORMACIN SOBRE LA ENERGA DE RF Y SU CONTROL, PARA GARANTIZAR SU CONFORMIDAD CON LOS LMITES DE EXPOSICIN A LA ENERGA DE RADIOFRECUENCIA ESTABLECIDOS EN LAS NORMAS NACIONALES E INTERNACIONALES APLICABLES. La informacin incluida en este documento reemplaza la informacin de seguridad general contenida en los manuales de usuario publicados antes de enero de 2008. MOTOROLA, MOTO, MOTOROLA SOLUTIONS y el logotipo estilizado M son marcas de fabrica o marcas registradas de Motorola Trademark Holdings, LLC y son usadas bajo licencia. Todas otras marcas registradas son la propiedad de sus dueos respectivos. 2005 2012 Motorola Solutions, Inc. Todos los derechos estn reservados. Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, EE.UU.

*NNTN7851D*

NNTN7851D

*6881095C99*

6881095C99-J Espaol Latinoamericano 6881095C99_SafetyM_LAS.fm Page 2 Tuesday, March 20, 2012 2:39 PM Informacin sobre exposicin a la energa de RF y su control, e instrucciones operacionales para satisfacer los requisitos de la FCC sobre el uso como herramienta ocupacional AVISO: Este radio est diseado para uso en ambientes ocupacionales controlados, donde los usuarios estn plenamente conscientes de la exposicin a la energa de radiofrecuencia a la que estn sujetos, y pueden ejercer control sobre dicha exposicin para mantenerse dentro de los lmites establecidos por la FCC. Esta unidad de radio NO est aprobada para la venta al pblico en general en el mercado de consumo masivo, ni para uso en entornos diferentes al aqu descrito. Este radio bidireccional usa energa electromagntica en el espectro de radiofrecuencia (RF) para permitir las comunicaciones a distancia entre dos o ms usuarios. El mismo emplea la energa de radiofrecuencia u ondas de radio para enviar y recibir llamadas. La energa de RF es una forma de energa electromagntica. Este tipo de energa se presenta en otras formas, entre las que se encuentran la luz solar y los rayos X. La energa de RF, sin embargo, no debe confundirse con estas otras formas de energa electromagntica que, cuando son usadas indebidamente, pueden ocasionar daos biolgicos. Niveles muy elevados de rayos X, por ejemplo, pueden producir daos en tejidos y en material gentico. Expertos en las ciencias, la ingeniera, la medicina, la salud y la industria trabajan conjuntamente con diferentes organizaciones con el fin de desarrollar normas que definan lmites prudentes de exposicin a la energa de RF. Estas normas proporcionan los niveles recomendados de exposicin a la RF, tanto para los trabajadores como para el pblico en general. Estos niveles recomendados de exposicin a la RF incluyen mrgenes de seguridad suficientemente amplios. Todos los radios bidireccionales Motorola son diseados, fabricados y probados de manera que aseguren el cumplimiento de los niveles de exposicin a la RF establecidos por los organismos pblicos reguladores. Asimismo, los fabricantes recomiendan a los usuarios de radios bidireccionales seguir instrucciones de operacin especficas. Estas instrucciones son importantes, ya que informan a los usuarios acerca de la exposicin a la energa de RF y proporcionan procedimientos sencillos para su control. Espaol Latinoamericano 2 6881095C99_SafetyM_LAS.fm Page 3 Tuesday, March 20, 2012 2:39 PM Visite los siguientes sitios Web para obtener ms informacin acerca de qu es la exposicin a la energa de RF y cmo controlar dicha exposicin para garantizar la observancia de los lmites de exposicin establecidos. http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Regulaciones de la Comisin Federal de Comunicaciones de EE.UU. Las normas de la FCC estipulan que los fabricantes de radios mviles bidireccionales no podrn comercializar sus productos en los EE.UU., a menos que los mismos cumplan con los lmites de exposicin a la energa de RF establecidos por la FCC. Cuando la naturaleza del trabajo requiere el uso de radios bidireccionales, la FCC exige que los usuarios estn totalmente conscientes de los efectos de la exposicin, y que sean capaces de controlar el nivel de exposicin al que se someten, a fin de satisfacer los requisitos laborales. La informacin sobre exposicin puede facilitarse mediante el uso de una etiqueta que remita a los usuarios a la fuente de informacin apropiada. Su radio bidireccional Motorola tiene una etiqueta con informacin acerca de la exposicin a la energa de RF. Adems, en el manual de usuario del producto Motorola, o en un folleto de seguridad separado, se incluye la informacin e instrucciones de operacin necesarias para controlar la exposicin a la energa de RF y para garantizar el cumplimiento de las normas. Conformidad con la normativa sobre exposicin a la RF Este radio bidireccional Motorola ha sido diseado y verificado con el fin de garantizar su compatibilidad con las siguientes normas y recomendaciones nacionales e internacionales relacionadas con la exposicin de seres humanos a la energa electromagntica de radiofrecuencia. Este radio cumple con los lmites de exposicin establecidos por el IEEE y por la ICNIRP para entornos ocupacionales o con control de exposicin a la energa de radiofrecuencia, a ciclos de trabajo de hasta 50% (50% transmisin y 50% recepcin) y ha sido aprobado por la FCC para uso como herramienta ocupacional solamente. En lo que respecta a la medicin de energa de RF para la determinacin de conformidad con las directrices de exposicin de la FCC, la antena del radio irradia energa de RF medible slo cuando est transmitiendo (cuando el usuario est hablando), no cuando est recibiendo (cuando el usuario est oyendo) o cuando se encuentra en espera. 3 Espaol Latinoamericano 6881095C99_SafetyM_LAS.fm Page 4 Tuesday, March 20, 2012 2:39 PM Este radio bidireccional Motorola satisface las siguientes normas y recomendaciones relacionadas con la exposicin a la energa de radiofrecuencia:

Comisin Federal de Comunicaciones de EE.UU. (FCC), Cdigo de Reglamentos Federales; 47 CFR y siguientes Comisin Federal de Comunicaciones de EE.UU. (FCC), Boletn OET 65 Instituto de Ingenieros Elctricos y Electrnicos (IEEE), C95.1 Comisin Internacional para la Proteccin contra la Radiacin No Ionizante

(ICNIRP) Ministerio de Sanidad (Canad), Cdigo de seguridad 6 Industria Canad, RSS-102 Direccin Australiana de Comunicaciones, Normativa de Radiocomunicaciones y siguientes ANATEL, Anexo a la Resolucin n 303 y siguientes. Pautas de conformidad y control de la exposicin de RF e instrucciones de operacin Para controlar la exposicin a la que tanto Ud. como otras personas se someten, y para asegurar el cumplimiento de los lmites de exposicin a la RF, observe siempre los siguientes procedimientos. Pautas:

El aparato debe ser acompaado de la informacin sobre la energa de RF cuando el mismo sea transferido a otros usuarios. No use este dispositivo sin antes satisfacer los requisitos operacionales aqu descritos. Espaol Latinoamericano 4 6881095C99_SafetyM_LAS.fm Page 5 Tuesday, March 20, 2012 2:39 PM Instrucciones:

No transmita ms del 50% del tiempo, a fin de no sobrepasar el mximo ciclo de trabajo especificado del 50%. Para transmitir (hablar) presione el botn de transmisin (PTT); si el radio est equipado con VOX, hable hacia el micrfono. El LED rojo se enciende cuando el radio est transmitiendo. Para recibir llamadas, suelte el botn PTT. Si el radio est equipado con VOX, deje de hablar. El LED rojo se apaga cuando el radio termina de transmitir. Es importante no transmitir ms del 50% del tiempo, ya que este radio emite energa de RF medible slo cuando est transmitiendo (en trminos de conformidad con las normas de medicin). Transmita nicamente cuando las personas que se encuentran fuera del vehculo estn apartadas por lo menos la distancia lateral mnima recomendada (indicada en la Tabla 1) de la carrocera de un vehculo equipado con una antena debidamente instalada. Esta separacin asegura que haya suficiente distancia entre una antena exterior debidamente instalada (segn las instrucciones de instalacin) para satisfacer los requisitos de exposicin a la energa de RF estipulados en las normas antes mencionadas. NOTA: La Tabla 1 presentada a continuacin indica la distancia lateral recomendada, en un entorno no controlado, a la que los transentes deben mantenerse de la carrocera de un vehculo equipado con una antena transmisora aprobada y debidamente instalada (es decir, monopolos sobre un plano de tierra, o bipolos) para diferentes niveles de potencia nominal de radios mviles instalados en un vehculo. Tabla 1. Potencia nominal del radio bidireccional mvil instalado en un vehculo y distancia lateral mnima recomendada de la carrocera del vehculo Potencia nominal del radio mvil

(ver nota) Menos de 7 vatios 7 a 14 vatios 15 a 39 vatios 40 a 110 vatios Distancia lateral mnima de la carrocera del vehculo 20 centmetros (8 pulg.) 30 centmetros (1 pie) 60 centmetros (2 pies) 90 centmetros (3 pies) 5 Espaol Latinoamericano 6881095C99_SafetyM_LAS.fm Page 6 Tuesday, March 20, 2012 2:39 PM Cuando se usa un radio mvil conjuntamente con otro transmisor ubicado en el mismo sitio como, por ejemplo, un repetidor vehicular, el operador del vehculo es responsable de tomar las medidas necesarias para mantener a los transentes alejados del vehculo la distancia mnima requerida, a fin de garantizar la conformidad con los lmites de exposicin a la energa de RF establecidos por la FCC para la poblacin en general. Para obtener ms detalles, consulte el manual de usuario de los transmisores ubicados en el mismo sitio. NOTA: Si no est seguro de cul es la potencia nominal de su radio, comunquese con el representante o concesionario Motorola e indquele el nmero de modelo del radio que aparece en la etiqueta del radio. Si no puede determinar la potencia nominal de salida, asegrese de mantener una separacin de un metro (3 pies) de la carrocera del vehculo. Los usuarios de radios multibanda sujetos a diferentes distancias de separacin en diferentes bandas de operacin conforme a la Tabla 1 deben seleccionar la distancia ms grande aplicable como la distancia lateral mnima para los transentes cercanos al vehculo. La potencia mxima mostrada en la autorizacin de la FCC puede ser mayor que la potencia nominal, tomando en consideracin las variaciones que ocurren a nivel de produccin. Pautas para la instalacin de antenas de radios mviles Las siguientes pautas para la instalacin de antenas de radios mviles son aplicables nicamente a vehculos automotores con carrocera metlica o a vehculos con planos de tierra apropiados. Las antenas deben ser instaladas en el rea central del techo o de la tapa del compartimiento de equipaje, tomando en consideracin las condiciones de exposicin de los pasajeros que viajen en el asiento trasero, as como las instrucciones y restricciones especficas mencionadas en el manual de instalacin del radio y los requisitos establecidos por el proveedor de la antena. La instalacin en la tapa del compartimiento de equipaje queda limitada a aquellos vehculos cuya tapa del compartimiento de equipaje sea una superficie plana claramente definida y, en algunos casos, a modelos especficos de radios y antenas. Consulte en el manual de instalacin del radio la informacin especfica sobre la ubicacin y la forma de instalar los diferentes tipos de antenas aprobados para satisfacer las distancias de operacin recomendadas entre las antenas y toda persona que pueda quedar expuesta. Espaol Latinoamericano 6 6881095C99_SafetyM_LAS.fm Page 7 Tuesday, March 20, 2012 2:39 PM Use nicamente la antena Motorola suministrada o una antena de reemplazo aprobada por Motorola. El uso de antenas, modificaciones o accesorios no aprobados podra daar el radio y constituir una violacin de las normas de seguridad relacionadas con la energa de RF. Accesorios aprobados Este radio ha sido probado y se ha determinado que satisface las normas de seguridad relacionadas con la energa de RF siempre que se use con los accesorios Motorola suministrados o designados para este producto. El uso de otros accesorios puede constituir una violacin de las normas de seguridad relacionadas con la energa de RF. Para obtener una lista de antenas y accesorios Motorola aprobados, consulte el manual de usuario para el modelo de radio. Informacin adicional Para obtener informacin adicional sobre los requisitos de exposicin o informacin sobre capacitacin, visite: http://responsibility.motorolasolutions.com/index.php/

ourapproach/wirelesscommhealth/. Pautas de control y conformidad, e instrucciones de operacin de radios bidireccionales mviles instalados como estaciones de control en emplazamientos fijos Si un equipo de radio mvil se instala en un lugar fijo y se hace funcionar como estacin de control o como unidad fija, la instalacin de la antena deber satisfacer los siguientes requisitos, a fin de garantizar un rendimiento ptimo y de cumplir con los lmites de exposicin a la energa de radiofrecuencia establecidos en las normas y pautas enumeradas en la pgina 4:

La antena se debe montar fuera del edificio, en el techo o en una torre, siempre que sea posible. Como en todas las instalaciones de antenas en emplazamientos fijos, es responsabilidad del portador de la licencia mantener el emplazamiento de conformidad con los reglamentos aplicables, y es posible que existan requisitos adicionales como mediciones de propagacin, colocacin de letreros y restricciones de acceso al emplazamiento. 7 Espaol Latinoamericano 6881095C99_SafetyM_LAS.fm Page 8 Tuesday, March 20, 2012 2:39 PM Para obtener informacin adicional sobre la instalacin, consulte las directrices relativas a las distancias de separacin antes mencionadas en la seccin de este documento titulada Pautas de conformidad y control de la exposicin de RF, e instrucciones de operacin. Pautas de Cumplimiento y Control e Instrucciones de Uso para usar radios bidireccionales mviles instalados en embarcaciones martimas Si el equipo de radio mvil est instalado en una embarcacin y funciona como una unidad fija, la instalacin de la antena debe cumplir con los siguientes requisitos con el fin de garantizar un rendimiento ptimo y cumplimiento de los lmites de exposicin a la energa de RF en las normas y pautas que figuran en la pgina 4:

Una antena destinada a la operacin Martima se debe elegir e instalar de acuerdo con las recomendaciones de los fabricantes. Las antenas se deben montar firmemente a la estructura de la embarcacin en el lugar ms alto posible. De la misma forma que con todas las instalaciones de antena de radio, es responsabilidad del operador mantener una distancia adecuada hasta la antena y de todo el personal a bordo del barco o que se encuentre en sus proximidades. Si desea obtener informacin adicional sobre la instalacin, consulte las directrices sobre distancias de separacin mnimas indicadas anteriormente en la seccin Pautas de conformidad y control de la exposicin de RF einstrucciones de operacin de este documento. Interferencia y compatibilidad electromagntica NOTA: Casi todos los dispositivos electrnicos son susceptibles a la interferencia electromagntica si no cuentan con el debido blindaje, o si no estn diseados o configurados de manera que sean compatibles con este tipo de seales electromagnticas. Puede que sea necesario realizar pruebas de compatibilidad para determinar si alguno de los equipos electrnicos usados en los vehculos, cerca de ellos o cerca de antenas en emplazamientos fijos, es sensible a la energa de radiofrecuencia externa, o si hay que ejecutar algn procedimiento para eliminar o reducir la posibilidad de interaccin entre el radio transmisor y el equipo o dispositivo. Espaol Latinoamericano 8 6881095C99_SafetyM_LAS.fm Page 9 Tuesday, March 20, 2012 2:39 PM Edificaciones Para evitar problemas de interferencia y/o compatibilidad electromagntica, apague el radio en todos los lugares donde haya letreros que as lo establezcan. Por ejemplo, en hospitales e instalaciones de asistencia mdica podran estar usando aparatos sensibles a la energa de RF externa. Vehculos Para evitar una posible interaccin entre el radio transmisor y cualquiera de los mdulos de control electrnico del vehculo (por ejemplo, el control del sistema antibloqueo de frenos (ABS), el control del motor o el control de la transmisin), se debe contratar a un instalador experimentado para realizar la instalacin del radio, as como tomar las siguientes precauciones:

1. Consulte las instrucciones proporcionadas por el fabricante y dems boletines tcnicos que contengan recomendaciones para la instalacin del radio. 2. Antes de instalar el radio, determine la ubicacin de los mdulos de control electrnico y del tendido de los cables del vehculo. 3. Haga pasar todo el cableado del radio, incluida la lnea de transmisin de la antena, lo ms lejos posible de las unidades de control electrnico y del tendido de cables correspondiente. Seguridad al conducir Consulte las leyes y reglamentos para el uso de radios en las zonas donde conduce. Obedzcalas siempre. Cuando utilice el radio al conducir un vehculo:

Preste atencin al camino y a las condiciones de conduccin. Salga del camino y estacione el vehculo antes de realizar o contestar una llamada, si la situacin lo amerita. Seguridad acstica La exposicin a ruidos intensos provenientes de cualquier fuente por perodos de tiempo prolongados podran afectar su capacidad auditiva de forma temporal o permanente. Mientras ms alto sea el volumen del radio, ms pronto podra resultar afectada su capacidad auditiva. El dao auditivo producido por ruidos 9 Espaol Latinoamericano 6881095C99_SafetyM_LAS.fm Page 10 Tuesday, March 20, 2012 2:39 PM intensos a veces puede que sea imperceptible al principio, pero puede tener un efecto acumulativo. Para proteger su capacidad auditiva:

Use el menor volumen que le permita realizar sus tareas. Aumente el volumen nicamente cuando est en un entorno ruidoso. Disminuya el volumen antes de conectar un audfono o un auricular. Lmite el tiempo de uso de audfonos o auriculares a alto volumen. Cuando use el radio sin un audfono o auricular, no se coloque el parlante del radio pegado a la oreja. Espaol Latinoamericano 10 6881095C99_SafetyM_LAS.fm Page 11 Tuesday, March 20, 2012 2:39 PM Advertencias operacionales ADVERTENCIA ADVERTENCIA Vehculos con bolsas de aire No instale ni coloque un radio mvil sobre una bolsa de aire ni en el rea de despliegue de la misma. Las bolsas de aire se inflan con mucha fuerza. Si se coloca un radio en el rea de despliegue de la bolsa de aire, cuando sta se infle el radio podra salir proyectado con gran velocidad y ocasionar lesiones graves a los pasajeros. Ambientes potencialmente explosivos Apague el radio antes de entrar en reas con atmsferas potencialmente explosivas. Las chispas en atmsferas potencialmente explosivas pueden desencadenar explosiones o incendios, y ocasionar lesiones e incluso la muerte. Entre los entornos potencialmente explosivos se encuentran las reas con combustible, por ejemplo, debajo de la cubierta de barcos, instalaciones de transferencia y almacenamiento de combustible o de productos qumicos, y reas donde el aire contiene productos qumicos o partculas tales como polvo de cereales, polvo comn o polvo metlico. En las reas con atmsferas potencialmente explosivas generalmente hay seales de precaucin, aunque no siempre es as. reas de voladuras y explosivos Para evitar una posible interferencia con las operaciones de detonacin, apague el radio cuando est cerca de detonadores elctricos, en un rea de detonaciones o donde haya letreros que indiquen apagar los radios bidireccionales. Obedezca todas las seales e instrucciones. Para el caso de radios instalados en vehculos propulsados por gas licuado de petrleo, consulte la norma NFPA 58 de la Asociacin nacional estadounidense de proteccin contra incendios (National Fire Protection Association) para obtener informacin sobre almacenamiento, manejo y/

o contenedores. Para obtener una copia de la norma NFPA 58 comunquese con la Asociacin nacional estadounidense de proteccin contra incendios (National Fire Protection Association), One Battery Park, Quincy, MA, EE. 11 Espaol Latinoamericano 6881095C99_SafetyM_LAS.fm Page 12 Tuesday, March 20, 2012 2:39 PM Espaol Latinoamericano 12 6881095C99_SafetyM_BP.fm Page 1 Tuesday, March 6, 2012 11:23 AM Guia de Exposio Energia RF e de Segurana do Produto para Rdios Portteis de Duas Vias Instalados em Veculos, Embarcaes ou como Estaes de Controle de Local Fixo ATENO ANTES DE UTILIZAR O RDIO PROCURE LER ESTE FOLHETO, QUE CONTM IMPORTANTES INSTRUES DE OPERAO PARA O USO SEGURO, BEM COMO INFORMAES SOBRE A ENERGIA DE RF E SEU CONTROLE, COM A FINALIDADE DE GARANTIR A CONFORMIDADE COM OS LIMITES DE EXPOSIO ENERGIA DE RADIOFREQNCIA ESTABELECIDOS NAS NORMAS NACIONAIS E INTERNACIONAIS APLICVEIS. As informaes contidas neste documento substituem as informaes a respeito de segurana geral contidas nos manuais do usurio publicados antes de janeiro de 2008. MOTOROLA, MOTO, MOTOROLA SOLUTIONS e o logotipo do M estilizado so marcas registradas ou marcas comerciais da Motorola Trademark Holdings, LLC e so usadas mediante licena. Todas as outras marcas registradas so de propriedade de seus respectivos proprietrios. 2005 2012 Motorola Solutions, Inc. Todos os direitos reservados. Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, EUA.

*NNTN7851D*

NNTN7851D

*6881095C99*

6881095C99-J Portugus Brasileiro 6881095C99_SafetyM_BP.fm Page 2 Tuesday, March 6, 2012 11:23 AM Informaes sobre a exposio energia de RF e seu controle, e instrues operacionais para satisfazer os requisitos da FCC sobre o uso como ferramenta ocupacional AVISO: Este rdio foi projetado para ser usado em ambientes ocupacionais controlados, onde os usurios estejam plenamente conscientes da exposio energia de radiofreqncia a que esto sujeitos e podem exercer o controle sobre tal exposio de modo a satisfazer as exigncias de limites de exposio estabelecidos pelo FCC. Esta unidade de rdio NO se destina a venda ao pblico em geral no mercado de consumo de massa, nem se destina ao uso em ambientes diferentes daqueles aqui descritos. Este rdio bidirecional utiliza energia eletromagntica no espectro de radiofreqncia (RF) para permitir a comunicao distncia entre dois ou mais usurios. O rdio utiliza a energia de radiofreqncia ou ondas de rdio para enviar e receber chamadas. A energia de RF uma forma de energia eletromagntica. Este tipo de energia se apresenta sob outras formas, dentre as quais se incluem a luz solar e os raios X. A energia de RF, contudo, no deve ser confundida com estas outras formas de energia eletromagntica que, quando so usadas indevidamente, podem causar danos biolgicos. Nveis muito elevados de raios X, por exemplo, podem produzir danos aos tecidos e ao material gentico. Especialistas em cincias, engenharia, medicina, sade e indstria tm trabalhado conjuntamente com as diferentes organizaes com a finalidade de desenvolver normas que definem os limites prudentes de exposio energia de RF. Estas normas proporcionam os nveis recomendveis de exposio RF, tanto para os trabalhadores quanto para o pblico em geral. Estes nveis recomendados de exposio energia de RF incluem margens de segurana suficientemente amplas. Todos os rdios bidirecionais Motorola so projetados, fabricados e testados de maneira segura de modo a assegurar o cumprimento dos nveis de exposio RF estabelecidos pelos organismos pblicos reguladores. Alm disto, os fabricantes recomendam aos usurios de rdios bidirecionais que sigam as instrues de operao especficas. Estas instrues so importantes uma vez que informam aos usurios a respeito da exposio energia de RF e oferecem procedimentos simples para seu controle. Portugus Brasileiro 2 6881095C99_SafetyM_BP.fm Page 3 Tuesday, March 6, 2012 11:23 AM Visite os websites indicados a seguir para obter mais informaes sobre o que se trata a exposio energia de RF e de como controlar esta exposio de modo a garantir a observncia dos limites de exposio estabelecidos. http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Regulamentos da Comisso Federal de Comunicaes dos Estados Unidos As normas do FCC estipulam que os fabricantes de rdios mveis bidirecionais no podero comercializar seus produtos nos Estados Unidos exceto se tais produtos cumprirem com as exigncias de limites de exposio energia de RF estabelecidos pelo FCC. Quando a natureza do trabalho requer o uso de rdios bidirecionais, o FCC exige que os usurios estejam totalmente conscientes dos efeitos da exposio e que sejam capazes de controlar o nvel de exposio a que esto submetidos de modo a satisfazer as exigncias do trabalho. As informaes sobre exposio podem ser facilitadas por meio do uso de uma etiqueta que remeta os usurios fonte de informaes apropriadas. Seu rdio bidirecional Motorola contm uma etiqueta com informaes sobre a exposio energia de RF. Alm disto, no manual do usurio do produto Motorola, ou em um folheto de segurana publicado em separado, esto includas as informaes e instrues de operao necessrias para controlar a exposio energia de RF e para garantir o cumprimento das normas. Conformidade com a normativa sobre a exposio RF Este rdio bidirecional Motorola foi projetado e testado com a finalidade de garantir a sua compatibilidade com as normas e recomendaes nacionais e internacionais descritas a seguir no que se refere a exposio de seres humanos energia eletromagntica de radiofreqncia. Este rdio atende aos limites de exposio estabelecidos pelo IEEE e pela ICNIRP para ambientes ocupacionais ou com controle de exposio energia de radiofreqncia, em ciclos de trabalho de at 50% (50% transmisso/50% recepo) e foi aprovado pelo FCC para uso somente como ferramenta ocupacional. No que se refere medio da energia de RF para a determinao de conformidade com as diretrizes de exposio do FCC, a antena do rdio irradia energia de RF mensurvel somente quando est transmitindo (quando o usurio est falando) e no quando est recebendo

(quando o usurio est ouvindo) ou quando se encontra em espera. 3 Portugus Brasileiro 6881095C99_SafetyM_BP.fm Page 4 Tuesday, March 6, 2012 11:23 AM Este rdio bidirecional Motorola satisfaz s seguintes normas e recomendaes relacionadas exposio energia de radiofreqncia:

Comisso Federal de Comunicaes dos Estados Unidos (FCC), Cdigo de Regulamentos Federais; 47 CFR e seguintes Comisso Federal de Comunicaes dos Estados Unidos (FCC), Boletim OET 65 Instituto de Engenheiros Eltricos e Eletrnicos (IEEE) C95.1 Comisso Internacional para Proteo contra Radiao no Ionizante (ICNIRP) Ministrio da Sade (Canad), Cdigo de segurana 6 Indstria Canad, RSS-102 Autoridade Australiana de Comunicaes, Normativa de Radiocomunicaes e seguintes ANATEL, Anexo Resoluo N. 303 e seguintes. Orientaes gerais de conformidade e controle da exposio de RF e instrues de operao Para controlar a exposio a que tanto o usurio como outras pessoas se submetem, e para assegurar o cumprimento dos limites de exposio RF, deve-se observar sempre os procedimentos descritos a seguir. Orientaes gerais:

O equipamento deve estar acompanhado das informaes relacionadas com a energia de RF quando o mesmo for transferido a outros usurios. No utilize este dispositivo sem antes satisfazer os requisitos operacionais aqui descritos. Portugus Brasileiro 4 6881095C99_SafetyM_BP.fm Page 5 Tuesday, March 6, 2012 11:23 AM Instrues:

No transmita mais de 50% do tempo, de modo a no ultrapassar o mximo ciclo de trabalho especificado de 50%. Para transmitir (falar) pressione o boto de transmisso (PTT); se o rdio estiver equipado com VOX, fale junto ao microfone. O LED vermelho acende quando o rdio est transmitindo. Para receber chamadas, solte o boto PTT. Se o rdio estiver equipado com VOX, pare de falar. O LED vermelho se apaga quando o rdio encerra a transmisso. importante no transmitir mais de 50% do tempo, uma vez que o rdio emite energia de RF mensurvel somente quando est em transmisso (em termos da conformidade com as normas de medio). Transmita somente quando as pessoas de fora do veculo se encontrarem afastadas pelo menos distncia lateral mnima recomendada (conforme mostrado na tabela 1) da carroceria de um veculo equipado com antena devidamente instalada. Esta separao assegura que haja distncia suficiente entre uma antena exterior devidamente instalada (conforme as instrues de instalao) para satisfazer os requisitos de exposio energia de RF estipulados nas normas acima mencionadas. NOTA: A tabela 1 mostrada a seguir indica a distncia lateral recomendada, em um ambiente no controlado, que deve ser mantida pelos transeuntes em relao carroceria de um veculo equipado com uma antena transmissora aprovada e devidamente instalada (isto , monopolos sobre um plano de terra, ou bipolos) para diferentes nveis de potncia nominal de rdios mveis instalados em um veculo. Tabela 1. Potncia nominal do rdio bidirecional mvel instalado em um veculo e distncia lateral mnima recomendada da carroceria do veculo Potncia nominal do rdio mvel (ver nota) Distncia lateral mnima da carroceria do veculo Menos de 7 watts 20 centmetros (8 polegadas) 7 a 14 watts 15 a 39 watts 40 a 110 watts 30 centmetros (1 p) 60 centmetros (2 ps) 90 centmetros (3 ps) 5 Portugus Brasileiro 6881095C99_SafetyM_BP.fm Page 6 Tuesday, March 6, 2012 11:23 AM Quando um rdio mvel utilizado juntamente com outro transmissor co-localizado como, por exemplo, um repetidor veicular, o operador do veculo ser responsvel por tomar as medidas necessrias para manter os transeuntes distncia mnima exigida do veculo, de modo a garantir a conformidade com os limites de exposio energia de RF estabelecidos pela FCC para a populao em geral. Para obter mais detalhes, consulte o manual do usurio dos transmissores co-localizados. NOTA: Se no tiver certeza sobre o valor da potncia nominal de seu rdio, entre em contato com o representante ou a concessionria Motorola e informe o nmero de modelo do rdio que aparece na etiqueta do rdio. Se no for possvel determinar a potncia de sada nominal, assegure-se de manter a separao de 1 metro (3 ps) da carroceria do veculo. Usurios de rdios multi-banda sujeitos a diferentes distncias de separao em diferentes bandas operacionais de acordo com a Tabela 1 devem selecionar a maior distncia aplicvel como a mnima distncia lateral para expectadores fora do veculo. A energia mxima exibida da Garantia FCC pode ser maior que a energia nominal permitida para a variao de produo. Orientaes gerais para a instalao das antenas de rdios mveis As orientaes gerais descritas a seguir para a instalao de antenas de rdios mveis se aplicam somente a veculos automotores com carroceria metlica ou a veculos com planos de terra apropriados. As antenas devem ser instaladas na rea central do teto ou da tampa do porta-

malas, levando em considerao as condies de exposio aplicveis aos passageiros do banco traseiro, bem como as instrues e restries especficas mencionadas no manual de instalao do rdio e os requisitos estabelecidos pelo fornecedor da antena. A instalao na tampa do porta-malas limitada a veculos cujas tampas do compartimento de porta-malas sejam planas e claramente definidas e, em alguns casos, a modelos especficos de rdios e antenas. Consulte no manual de instalao do rdio as informaes especficas sobre a localizao e a forma de instalar os diferentes tipos de antenas aprovados para satisfazer deste modo as exigncias de operao recomendadas e assim proteger as pessoas que possam estar expostas. Portugus Brasileiro 6 6881095C99_SafetyM_BP.fm Page 7 Tuesday, March 6, 2012 11:23 AM Use somente a antena Motorola fornecida ou uma antena de reposio aprovada pela Motorola. O uso de antenas, modificaes ou acessrios no aprovados poder resultar em dano ao rdio e se constituir em uma violao das normas de segurana em relao energia de RF. Acessrios aprovados Este rdio foi testado e constatou-se que satisfaz as normas de segurana em relao energia de RF sempre que utilizado com os acessrios Motorola fornecidos ou destinados a este produto. O uso de outros acessrios pode se constituir em uma violao das normas de segurana em relao energia de RF. Para uma lista de aprovados Motorola antenas e acessrios, consulte o manual do usurio manual para o seu modelo de rdio. Informaes adicionais Para obter informaes adicionais sobre os requisitos de exposio ou sobre treinamento, visite o seguinte website: http://responsibility.motorolasolutions.com/

index.php/ourapproach/wirelesscommhealth/. Orientaes gerais de controle e conformidade e instrues de operao de rdios mveis bidirecionais instalados como estaes de controle em locais fixos Se um equipamento de rdio mvel for instalado em um local fixo e o mesmo for colocado em funcionamento como uma estao de controle ou como uma unidade fixa, a instalao da antena dever satisfazer os requisitos descritos a seguir, de modo a garantir um rendimento otimizado e para atender aos limites de exposio energia de radiofreqncia estabelecidos nas normas e orientaes mencionadas na pgina 4:

Sempre que for possvel, a antena dever ser instalada fora do edifcio em um teto ou torre. Como acontece em todas as instalaes de antenas feitas em locais fixos, responsabilidade do licenciado manter o local em conformidade com os regulamentos aplicveis. Tambm possvel que existam requisitos adicionais tais como medies de propagao, colocao de sinalizao de aviso e outras restries de acesso ao local. 7 Portugus Brasileiro 6881095C99_SafetyM_BP.fm Page 8 Tuesday, March 6, 2012 11:23 AM Para obter informaes adicionais sobre a instalao, consulte as orientaes relativas s distncias mnimas de separao mencionadas anteriormente na seo denominada Orientaes de conformidade e controle da exposio de RF e instrues de operao, constantes nesse documento. Diretrizes de Conformidade e Controle e Instrues Operacionais para Rdios Portteis de Duas Vias Instalados em Embarcaes Martimas Se o equipamento de rdio porttil estiver instalado em uma embarcao e operado como unidade fixa, a instalao da antena deve estar em conformidade com os seguintes requerimentos para assegurar desempenho excelente e conformidade com os limites de exposio energia RF nos padres e diretrizes listadas na pgina 4:

Uma antena destinada para operao Martima deve ser escolhida e instalada de acordo com as recomendaes do fabricante. As antenas devem ser montadas solidamente estrutura da embarcao no local mais alto possvel. Como com todas as instalaes de antena de rdio, responsabilidade do operador manter distncias adequadas da antena e todo o pessoal a bordo da embarcao ou adjacente embarcao. Para informaes adicionais de instalao, veja as diretrizes para distncias de separao mnimas provadas acima na seo Diretrizes de Conformidade e Controle e Instrues Operacionais deste documento. Interferncia e compatibilidade eletromagntica NOTA: Quase todos os dispositivos eletrnicos so susceptveis interferncia eletromagntica se no estiverem devidamente blindados ou se no tiverem sido projetados ou configurados de maneira a serem compatveis com estes tipos de sinais eletromagnticos. possvel que seja necessrio realizar testes de compatibilidade para se determinar se algum dos equipamentos eletrnicos usados nos veculos, prximo a eles ou prximo s instalaes de antenas feitas em locais fixos sensvel energia de radiofreqncia externa, ou se h necessidade de executar algum procedimento para eliminar ou reduzir a possibilidade de interao entre o rdio transmissor e o referido equipamento ou dispositivo. Portugus Brasileiro 8 6881095C99_SafetyM_BP.fm Page 9 Tuesday, March 6, 2012 11:23 AM Edificaes Para evitar problemas de interferncia e/ou compatibilidade eletromagntica, desligue o rdio em todos os locais onde houver avisos instruindo neste sentido. Por exemplo, em hospitais e estabelecimentos de assistncia mdica podem estar sendo utilizados equipamentos sensveis energia de RF externa. Veculos Para evitar uma possvel interao entre o rdio transmissor e qualquer um dos mdulos de controle eletrnico do veculo (por exemplo, o controle do sistema anti-

bloqueio de freios (ABS), o controle do motor ou o controle da transmisso), recomenda-se que se contrate um instalador experiente para realizar a instalao do rdio, bem como tomar as seguintes precaues:

1. Consulte as instrues fornecidas pelo fabricante e as demais documentaes tcnicas que contenham recomendaes para a instalao do rdio. 2. Antes de instalar o rdio, determine o local dos mdulos de controle eletrnico e do cabeamento no veculo. 3. Passe toda a fiao do rdio, incluindo a linha de transmisso da antena, o mais distante possvel das unidades de controle eletrnico e do cabeamento correspondente. Segurana ao dirigir Consulte as leis e regulamentos de trnsito referentes ao uso de rdios nos locais em que estiver dirigindo. Obedea sempre estas leis. Quando estiver utilizando o rdio ao dirigir:

Preste ateno ao volante quando estiver dirigindo. Saia da pista e estacione antes de fazer ou receber uma chamada, se as condies de trnsito assim o exigirem. Segurana acstica A exposio a rudos intensos provenientes de qualquer fonte durante perodos de tempo prolongados poder afetar a sua capacidade auditiva temporariamente ou de forma permanente. Quanto mais alto for o volume sonoro do rdio, mais rapidamente sua capacidade auditiva poder ser afetada. O dano auditivo produzido por rudos intensos s vezes poder ser imperceptvel em um primeiro momento. Porm, ele tende a se tornar um efeito cumulativo. 9 Portugus Brasileiro 6881095C99_SafetyM_BP.fm Page 10 Tuesday, March 6, 2012 11:23 AM Para proteger a sua capacidade auditiva:

Use a menor intensidade de volume que permita a realizao de suas tarefas. Aumente o volume somente quando estiver em um ambiente ruidoso. Abaixe o volume antes de conectar um fone de ouvido ou acessrio auricular. Limite o tempo de uso de fones de ouvido ou de acessrios auriculares em volume alto. Quando estiver utilizando o rdio sem um fone de ouvido ou acessrio auricular, no coloque o alto-falante do rdio muito prximo ao ouvido. Portugus Brasileiro 10 6881095C99_SafetyM_BP.fm Page 11 Tuesday, March 6, 2012 11:23 AM ADVERTNCIA ADVERTNCIA Advertncias operacionais Veculos com air bag No instale nem coloque um rdio mvel sobre um air bag nem na rea prxima expanso do mesmo. O air bag se expande com grande intensidade. Se houver um rdio porttil na rea de expanso do air bag quando da expanso do mesmo, o rdio poder ser lanado com grande velocidade e causar leses graves aos passageiros. Ambientes potencialmente explosivos Desligue o rdio antes de entrar em reas com atmosferas potencialmente inflamveis. As fascas lanadas em ambientes potencialmente explosivos podem causar uma exploso ou incndio e resultar em leses graves ou inclusive fatais. Entre os ambientes potencialmente explosivos esto as reas com combustveis situadas, por exemplo, na parte inferior de embarcaes, instalaes de transferncia e armazenamento de combustveis ou de produtos qumicos, e reas onde o ar possa conter produtos qumicos ou partculas tais como cereais, poeira comum ou poeira metlica. As reas com ambientes potencialmente explosivos geralmente contm avisos de advertncia, embora nem sempre seja assim. reas de detonao e exploso Para evitar uma possvel interferncia com as operaes de detonao, desligue o rdio quando estiver prximo de detonadores eltricos, em reas de detonao ou onde houver avisos indicando para desligar os rdios bidirecionais. Siga todos os avisos e instrues. No caso de rdios instalados em veculos movidos a gs liqefeito de petrleo, consulte a norma NFPA 58 da Associao Nacional de Proteo contra Incndios dos EUA (National Fire Protection Association) para obter informaes a respeito do armazenamento, manuseio e/ou recipientes. Para obter uma cpia da norma NFPA 58 entre em contato com a Associao Nacional de Proteo contra Incndios, One Battery Park, Quincy, MA, EUA. 11 Portugus Brasileiro 6881095C99_SafetyM_BP.fm Page 12 Tuesday, March 6, 2012 11:23 AM Portugus Brasileiro 12 6881095C99_SafetyM_FrCan.fm Page 1 Tuesday, March 6, 2012 11:17 AM Guide dexposition aux frquences radio (RF) et de scurit des produits pour radios mobiles bidirectionnelles installes dans des vhicules, des navires ou comme stations fixes de surveillance de sites ATTENTION AVANT DUTILISER CETTE RADIO, LISEZ CETTE BROCHURE QUI CONTIENT DIMPORTANTES INFORMATIONS SUR LE MODE DEMPLOI SCURITAIRE DU PRODUIT AINSI QUE DES INFORMATIONS RELATIVES LNERGIE DE RF ET SON CONTRLE, AFIN DASSURER LA CONFORMIT AUX LIMITES DEXPOSITION LNERGIE DE RADIOFRQUENCE TABLIES PAR LES NORMES NATIONALES ET INTERNATIONALES APPLICABLES. Les informations contenues dans ce document remplacent les informations gnrales de scurit des manuels de lutilisateur publis avant janvier 2008. MOTOROLA, MOTO, MOTOROLA SOLUTIONS et le logo M stylis sont des marques de commerce ou des marques enregistres de Motorola Trademark Holdings, LLC et sont utilises sous licence. Toutes les autres marques de commerce appartiennent leurs propritaires respectifs. 2005 2012 Motorola Solutions, Inc. Tous droits rservs. Motorola Solutions, Inc. 1303 E. Algonquin Rd., Schaumburg, IL 60196, tats-Unis.

*NNTN7851D*

NNTN7851D

*6881095C99*

6881095C99-J Franais Canadien 6881095C99_SafetyM_FrCan.fm Page 2 Tuesday, March 6, 2012 11:17 AM Sensibilisation lexposition lnergie de RF, moyens de contrle et consignes dutilisation pour conformit aux normes du FCC en matire dusage professionnel de cette radio AVIS: Cette radio a t conue pour un usage professionnel dans un environnement contrl, o les utilisateurs sont pleinement conscients de lexposition lnergie de RF laquelle ils sont soumis et peuvent exercer un contrle sur cette exposition afin de respecter les limites tablies par le FCC. Ce dispositif radio Nest PAS autoris pour lensemble de la population, les consommateurs en gnral, ni pour une utilisation autre que celle dcrite ici. Cette radio bidirectionnelle utilise de lnergie lectromagntique dans le spectre des radiofrquences (RF) pour permettre les communications distance entre deux utilisateurs ou plus. Elle utilise lnergie de radiofrquence ou les ondes radio pour mettre et recevoir des appels. Lnergie de RF est une forme dnergie lectromagntique. Ce type dnergie se prsente sous dautres formes, notamment la lumire solaire et les rayons X. Il ne faut cependant pas confondre lnergie de RF avec dautres formes dnergie lectromagntique qui, lorsquelles sont mal utilises, peuvent occasionner des dommages biologiques. Des niveaux trs levs de rayons X, par exemple, peuvent endommager les tissus et le matriel gntique. Les experts en science, en ingnierie, en mdecine, en sciences de la sant et lindustrie travaillent en collaboration avec diffrentes organisations afin dlaborer des normes dfinissant les limites acceptables dexposition lnergie de RF. Ces normes fournissent les niveaux recommands dexposition aux RF, tant pour les travailleurs que pour le public en gnral. Ces niveaux recommands dexposition aux RF comprennent des marges de scurit apprciables. Toutes les radios bidirectionnelles Motorola sont conues, fabriques et testes de manire garantir leur conformit aux niveaux dexposition aux RF tablis par les autorits publiques comptentes. Par ailleurs, les fabricants recommandent aux utilisateurs de radios bidirectionnelles de suivre des directives de fonctionnement spcifiques. Ces directives sont importantes puisquelles informent les utilisateurs sur lexposition lnergie de RF et proposent des moyens simples pour la contrler. Franais Canadien 2 6881095C99_SafetyM_FrCan.fm Page 3 Tuesday, March 6, 2012 11:17 AM Visitez les sites Web suivants pour obtenir plus de renseignements sur ce quest lnergie de RF et sur les mesures de contrles observer afin de respecter les limites tablies en matire dexposition aux RF. http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Rglements du Conseil Fdral Amricain des Communications

(FCC) Les rglements du FCC stipulent que les fabricants de radios mobiles bidirectionnelles ne peuvent commercialiser leurs produits aux tats-Unis quaprs avoir vrifi leur conformit aux limites dexposition lnergie de RF tablies par le FCC. Lorsque les radios bidirectionnelles sont utilises des fins professionnelles, le FCC exige que les utilisateurs soient pleinement conscients des effets de lexposition et quils soient capables de contrler le niveau dexposition auquel ils se soumettent, afin de rpondre aux exigences de leur profession. Vous pouvez contribuer la sensibilisation lexposition aux RF en apposant des tiquettes renvoyant les utilisateurs vers la source dinformation approprie. Votre radio bidirectionnelle Motorola comporte une tiquette de produit sur lexposition lnergie de RF. Dautre part, vous trouverez dans le manuel de lutilisateur du produit Motorola ou dans la brochure de scurit fournie sparment, les informations requises et le mode demploi permettant de contrler lexposition lnergie de RF et de garantir le respect des normes. Conformit aux normes sur lexposition aux RF Cette radio bidirectionnelle Motorola a t conue et teste afin de garantir sa conformit aux normes et recommandations nationales et internationales ci-dessous lies lexposition des tres humains lnergie lectromagntique de radiofrquence. Cette radio respecte les limites dexposition tablies par l'IEEE et la ICNIRP pour les environnements professionnels ou avec contrle dexposition lnergie de radiofrquence, des cycles de travail allant jusqu 50% (50% transmission/50% rception) et est approuv par le FCC pour un usage exclusivement professionnel. En ce qui concerne la mesure de lnergie de RF afin dvaluer la conformit aux normes dexposition du FCC, la radio met de lnergie de RF mesurable seulement lorsquelle est en cours de transmission

(conversation), et non pas lorsquelle reoit (coute) ni quand elle est en mode Attente. 3 Franais Canadien 6881095C99_SafetyM_FrCan.fm Page 4 Tuesday, March 6, 2012 11:17 AM Cette radio bidirectionnelle Motorola est conforme aux normes et aux lignes directrices suivantes relatives lexposition lnergie de RF:

Conseil fdral amricain des communications (FCC), Code de la rglementation fdrale ; 47CFR et suiv. Conseil fdral amricain des communications (FCC), Bulletin OET 65 Institut des ingnieurs lectriciens et lectroniciens (IEEE), C95.1 Comit international pour la protection contre les radiations non ionisantes

(ICNIRP) Ministre de la sant (Canada), Code de scurit 6 Industrie Canada, RSS-102 Direction australienne de communications, norme de radiocommunications, et suiv. Annexe dANATEL la rsolution No. 303 et suiv. Directives en matire de conformit et de contrle dexposition aux RF et consignes de fonctionnement Pour contrler lexposition laquelle vous-mme et dautres personnes se soumettent et garantir le respect des limites dexposition aux RF, observez toujours les consignes suivantes. Consignes:

Lorsque lappareil est cd dautres utilisateurs, il doit tre accompagn des informations de sensibilisation des utilisateurs. Nutilisez pas cet appareil si les conditions de fonctionnement dcrites ici ne sont pas runies. Franais Canadien 4 6881095C99_SafetyM_FrCan.fm Page 5 Tuesday, March 6, 2012 11:17 AM Consignes:

Nmettez pas plus de 50% du temps afin de ne pas dpasser le cycle maximal de travail spcifi de 50%. Pour mettre (parler), appuyez sur le bouton de transmission (PTT) ou, si la radio est quipe de VOX, parlez dans le microphone. La DEL rouge sallume lorsque la radio met. Pour recevoir des appels, relchez le bouton PTT, ou, si la radio est quipe de VOX, arrtez de parler. La DEL rouge steint lorsque la radio arrte dmettre. Il est important de ne pas mettre plus de 50% du temps tant donn que cette radio gnre une nergie de RF dont lexposition nest mesurable que lors de lmission (en termes de conformit aux normes de mesure). Lmission ne doit se faire que lorsque les personnes situes lextrieur du vhicule se trouvent la distance latrale minimale recommande (indique dans le tableau 1) de la carrosserie dun vhicule quip dune antenne convenablement installe. Cette sparation garantit une distance suffisante par rapport une antenne extrieure convenablement installe (conformment aux consignes dinstallation) pour rpondre aux exigences en matire dexposition lnergie de RF stipules dans les normes mentionnes plus haut. REMARQUE: Le tableau 1 ci-dessous indique la distance latrale minimum recommande, dans un environnement non contrl, pour les passants par rapport la carrosserie dun vhicule quip dune antenne mettrice agre et convenablement installe (cest--dire, antenne unipolaire plan de sol, ou doublet) pour diffrents niveaux de puissance nominale de radios mobiles installes dans un vhicule. Tableau 1. Puissance nominale de la radio bidirectionnelle mobile installe dans un vhicule et distance latrale minimale recommande de la carrosserie du vhicule Puissance nominale de la radio mobile (voir Remarque) Moins de 7 watts 7 14 watts 15 39 watts 40 110 watts Distance latrale minimale de la carrosserie du vhicule 20 centimtres (8 pouces) 30 centimtres (1 pied) 60 centimtres (2 pieds) 90 centimtres (3 pieds) 5 Franais Canadien 6881095C99_SafetyM_FrCan.fm Page 6 Tuesday, March 6, 2012 11:17 AM Lorsqu'une radio mobile est utilise avec un autre metteur ayant la mme position, par exemple un rpteur vhiculaire, il incombe l'oprateur du vhicule de prendre les mesures ncessaires pour maintenir les tiers la distance requise du vhicule de faon garantir la conformit aux limites d'exposition l'nergie de RF tablies par la FCC pour le public en gnral. Pour plus de renseignements, consultez le guide de l'utilisateur relatif aux metteurs ayant la mme position. REMARQUE: Si vous ntes pas sr de la puissance nominale de votre radio, contactez le reprsentant ou le concessionnaire Motorola et indiquez-

lui le numro de modle de la radio qui figure sur ltiquette de celle-ci. Si vous narrivez pas dterminer la puissance de sortie nominale, conservez une distance dun mtre (3 pieds) par rapport la carrosserie du vhicule. Les utilisateurs de radio multi-bandes soumises diffrentes distances de sparation dans diffrentes bandes de fonctionnement selon le tableau 1 devront slectionner la plus grande distance applicable comme distance latrale minimale pour les personnes se trouvant l'extrieur du vhicule. La puissance maximale indique sur lautorisation de la FCC peut tre suprieure la puissance nominale si lon tient compte des variations de production. Consignes dinstallation pour les antennes de radios mobiles Les consignes suivantes pour linstallation dantennes de radios mobiles sont applicables uniquement aux vhicules automobiles carrosserie mtallique ou aux vhicules plans de sol appropris. Les antennes doivent tre installes au centre du toit ou du capot du coffre, en tenant compte des conditions dexposition des passagers du sige arrire, ainsi que des consignes et restrictions spcifiques mentionnes dans le manuel dinstallation de la radio et des exigences tablies par le fournisseur de lantenne. Les installations sur le capot du coffre sont rserves aux vhicules quips de coffres surfaces planes clairement dfinies et dans la plupart des cas, des modles spcifiques de radios et dantennes. Consultez dans le manuel dinstallation de la radio les informations spcifiques relatives lemplacement et au mode dinstallation des diffrents types dantennes agrs, destines fournir toute personne risquant dtre expose les distances de fonctionnement recommandes. Utilisez uniquement lantenne agre fournie par Motorola ou une antenne de rechange agre Motorola. Lutilisation dantennes, de modifications ou Franais Canadien 6 6881095C99_SafetyM_FrCan.fm Page 7 Tuesday, March 6, 2012 11:17 AM daccessoires non agrs peut endommager la radio et constituer une violation des normes de scurit en matire dnergie de RF. Accessoires agrs Cette radio a t teste et dclare conforme aux normes de scurit en matire dnergie de RF lorsquelle est utilise avec les accessoires Motorola fournis ou dsigns pour ce produit. Lutilisation dautres accessoires peut constituer une violation des normes de scurit en matire dnergie de RF. Pour obtenir une liste de Motorola antennes approuves et accessoires, reportez-

vous l'utilisateur manuel de votre modle de radio. Informations complmentaires Pour obtenir plus de renseignements sur les exigences en matire dexposition ou des informations de formation, visitez le site: http://

responsibility.motorolasolutions.com/index.php/ourapproach/wirelesscommhealth/. Directives de contrle et de conformit et consignes de fonctionnement des radios bidirectionnelles mobiles installes comme stations de contrle emplacements fixes. Si un appareil de radio mobile est install dans un endroit fixe et quil est utilis comme station de contrle ou comme unit fixe, linstallation de lantenne doit rpondre aux exigences ci-dessous afin de garantir un rendement optimal et de respecter les limites dexposition lnergie de RF tablies dans les normes et directives numres page 4 :

Dans la mesure du possible, lantenne doit tre monte sur le toit ou sur une tour, lextrieur du btiment. Comme pour toutes les installations dantennes emplacements fixes, il incombe au grant de maintenir lemplacement en conformit avec les rglements en vigueur. Par ailleurs, dautres exigences peuvent sappliquer, telles que des mesures de propagation, la pose de panneaux et des restrictions de laccs lemplacement afin dtre certain que les limites dexposition mentionnes ne sont pas dpasses. Pour toute information d'installation supplmentaire, consultez les directives relatives aux distances de sparation minimum fournies ci-dessus dans la section de ce document intitule Directives en matire de conformit et de contrle d'exposition aux RF et consignes de fonctionnement. 7 Franais Canadien 6881095C99_SafetyM_FrCan.fm Page 8 Tuesday, March 6, 2012 11:17 AM Directivesdeconformitetdecontrleetconsignes d'exploitationpourlesradiosmobilesbidirectionnelles installssurlesnavires Si un appareil de radio mobile est install sur un navire et utilis comme appareil fixe, l'installation de l'antenne devra tre conforme aux exigences suivantes en vue d'assurer une performance optimale et le respect des limites d'exposition aux frquences radio

(RF) stipules dans les normes et lignes directrices figurant la page 4:

Une antenne usage maritime devra tre choisie et installe conformment aux Les antennes devront tre montes solidement la structure du navire et places le recommandations du fabricant. plus haut possible. Comme avec toutes les installations d'antennes de radio, il est de la responsabilit de l'exploitant de maintenir des distances suffisantes entre l'antenne et tout le personnel bord ou proximit du navire. Pour plus d'informations sur l'installation, voir les recommandations pour les distances de sparation minimales exposes ci-dessus dans les Recommandations pour la conformit et le contrle de lexposition aux RF, ainsi que la section Instructions dutilisation de ce document. Interfrence et compatibilit lectromagntique REMARQUE: La grande majorit des dispositifs lectroniques sont sensibles leffet lectromagntique perturbateur (EMI) sils ne sont pas convenablement protgs ou sils ne sont pas conus ou configurs de telle sorte quils soient compatibles avec ce type de signaux lectromagntiques. Il se peut que des tests de compatibilit soient ncessaires afin de dterminer si lun des appareils lectroniques utiliss lintrieur ou proximit des vhicules ou proximit dantennes emplacements fixes est sensible lnergie de RF externe ou sil faut prendre des mesures quelconques pour liminer ou attnuer le risque dinteraction entre la radio mettrice et lappareil ou le dispositif. Btiments Afin dviter des problmes dinterfrence et/ou de compatibilit lectromagntique, teignez la radio dans tous les tablissements o des panneaux daffichage vous invitent le faire. Il se peut, par exemple, que les hpitaux ou les tablissements de sant utilisent des appareils sensibles lnergie de RF externe. Franais Canadien 8 6881095C99_SafetyM_FrCan.fm Page 9 Tuesday, March 6, 2012 11:17 AM Vhicules Afin dviter une ventuelle interaction entre la radio mettrice et lun des modules de contrle lectronique du vhicule (par exemple, le contrle du systme de freinage antiblocage (ABS), le contrle du moteur ou le contrle de la transmission) il est recommand de faire appel uniquement un installateur qualifi pour raliser linstallation de la radio et de prendre les prcautions suivantes :

1. Consultez la notice du fabricant ou toute autre documentation technique contenant des recommandations pour linstallation de la radio. 2. Avant dinstaller la radio, dterminez lemplacement des modules de contrle lectronique et du cblage lintrieur du vhicule. 3. Faites passer tout le cblage de la radio, y compris la ligne de transmission de lantenne, le plus loin possible des units de contrle lectronique et du cblage correspondant. Scurit lors de la conduite Consultez la lgislation et les rglements en vigueur sur lutilisation des radios dans les zones o vous conduisez. Respectez toujours ces rgles. Lorsque vous utilisez la radio en conduisant:

Concentrez-vous entirement sur votre conduite et sur la route. Rangez-vous sur le bas-ct et stationnez votre vhicule avant de faire ou de rpondre un appel, si les conditions de conduite lexigent. Scurit acoustique L'exposition des bruits forts de n'importe quelle source pendant de longues priodes peut affecter temporairement ou de manire permanente votre audition. Plus le volume de la radio est lev, plus votre audition risque de se dtriorer rapidement. Les dommages auditifs causs par des bruits forts sont parfois indtectables au dbut et peuvent avoir un effet cumulatif. 9 Franais Canadien 6881095C99_SafetyM_FrCan.fm Page 10 Tuesday, March 6, 2012 11:17 AM Pour protger votre audition:

Rglez le volume au plus bas niveau possible ncessaire pour effectuer votre travail. volumes. N'augmentez le volume que si vous tes dans un environnement bruyant. Baissez le volume avant d'utiliser un casque ou des oreillettes. Utilisez le moins longtemps possible un casque ou des oreillettes de forts Lorsque vous utilisez la radio sans casque ou oreillettes, ne placez pas le haut-parleur de la radio directement sur votre oreille. Franais Canadien 10 6881095C99_SafetyM_FrCan.fm Page 11 Tuesday, March 6, 2012 11:17 AM AVERTISSEMENT AVERTISSEMENT Avertissements de fonctionnement Vhicules quips de sac gonflable vitez de monter ou de placer une radio mobile au-dessus dun sac gonflable ou dans la zone de dploiement de ce dernier. Les sacs gonflables se dploient avec une force considrable. Si une radio se trouve dans la zone de dploiement du sac lorsque celui-ci se gonfle, la radio peut tre propulse avec une force considrable et risque alors doccasionner de graves lsions corporelles aux passagers. Atmosphres potentiellement explosives teignez la radio avant de pntrer dans une atmosphre potentiellement explosive. La moindre tincelle dans ce type d'atmosphre peut provoquer une explosion ou un incendie et entraner des lsions corporelles ou mme la mort. Parmi les zones potentiellement explosives, citons les zones davitaillement en carburant, par exemple la cale des bateaux, les installations de transfert et de stockage de carburant ou de produits chimiques et les zones dans lesquelles lair est charg en produits chimiques ou en particules telles que de la poudre de crales, de la poussire ou de la poudre mtallique. Les zones atmosphres potentiellement explosives affichent gnralement des panneaux de mise en garde, mais ce nest pas toujours le cas. Dtonateurs et zones de dynamitage Afin dviter toute interfrence ventuelle avec les oprations de dtonation, teignez la radio proximit de dtonateurs lectriques, dans une zone de dtonations ou l o sont affichs des panneaux vous invitant teindre les radios bidirectionnelles. Respectez tous les panneaux et toutes les consignes. En ce qui concerne les radios installes dans des vhicules fonctionnant au GPL, consultez la norme NFPA 58 de lAssociation amricaine pour la protection contre lincendie (National Fire Protection Association) pour obtenir des informations sur le stockage, la manipulation et/ou les conteneurs. Pour obtenir une copie de la norme GPL, NFPA 58, contactez lAssociation amricaine pour la protection contre lincendie (National Fire Protection Association), One Battery Park, Quincy, MA. 11 Franais Canadien 6881095C99_SafetyM_FrCan.fm Page 12 Tuesday, March 6, 2012 11:17 AM Franais Canadien 12