all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
Antenna Installation Instructions | Users Manual | 50.84 KiB | ||||
1 2 |
|
Installation Manual | Users Manual | 668.98 KiB | ||||
1 2 |
|
Users Manual | Users Manual | 755.37 KiB | ||||
1 2 |
|
users Manual (revised) | Users Manual | 834.29 KiB | ||||
1 2 | Cover Letter(s) | April 02 2008 | ||||||
1 2 | Test Report | April 02 2008 | ||||||
1 2 | Attestation Statements | |||||||
1 2 | Block Diagram | |||||||
1 2 | External Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Internal Photos | |||||||
1 2 | RF Exposure Info | September 08 2000 | ||||||
1 2 | Operational Description | |||||||
1 2 | Parts List/Tune Up Info | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | RF Exposure Info | September 08 2000 | ||||||
1 2 | RF Exposure Info | |||||||
1 2 | RF Exposure Info | September 08 2000 | ||||||
1 2 | Schematics | |||||||
1 2 | Test Setup Photos |
1 2 | Installation Manual | Users Manual | 668.98 KiB |
i Section1 Radio Installation Table of Contents Chapter 1.1 Safety Information SAFE AND EFFICIENT OPERATION OF MOTOROLA TWO-WAY RADIOS ............. 1.1-1 EXPOSURE TO RADIO FREQUENCY ENERGY ............................................................. 1.1-1 PORTABLE RADIO OPERATION AND EME EXPOSURE ............................................. 1.1-1 ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY .......................................... 1.1-2 OPERATIONAL WARNINGS ............................................................................................. 1.1-2 OPERATIONAL CAUTIONS............................................................................................... 1.1-2 MOBILE RADIO OPERATION AND EME EXPOSURE .................................................. 1.1-3 ANTENNA INSTALLATION .............................................................................................. 1.1-3 Chapter 1.2 Introduction 1.2.1 General Information ....................................................................................... 1.2-4 1.2.2 Plan the Installation........................................................................................ 1.2-4 Chapter 1.3 DC Power Cable Installation 1.3.1 Planning the Power Cable Installation ........................................................... 1.3-5 1.3.2 Power Cable Installation Procedure............................................................... 1.3-5 Chapter 1.4 Trunnion Installation 1.4.1 Planning the Mounting Trunnion Installation.................................................. 1.4-8 1.4.2 Trunnion Installation Procedure ..................................................................... 1.4-8 1.4.3 Control Head Mounting Position .................................................................... 1.4-9 Chapter 1.5 Antenna Installation 1.5.1 Mobile Radio Operation and EME Exposure ............................................... 1.5-10 1.5.2 Selecting an Antenna Site............................................................................ 1.5-10 1.5.3 Mobile Antennas............................................................................. 1.5-10 Fixed Site Antennas ....................................................................... 1.5-11 1.5.4 1.5.5 Antenna Installation Procedure.................................................................... 1.5-11 1.5.6 Completing the Installation........................................................................... 1.5-12 ii Chapter 1.6 Installation Options 1.6.1 Radio Mounting in Dashboard ......................................................................1.6-14 1.6.2 External Speaker Installation........................................................................1.6-15 1.6.3 Remote Control Head Installation.................................................................1.6-16 1.6.3.1 Removing the Front Housing ..........................................................1.6-16 1.6.3.2 Assembling the Remote Front Housing ..........................................1.6-16 1.6.3.3 Assembling the Remote Back Housing...........................................1.6-16 1.6.3.4 Installing the Remote Control Head ................................................1.6-16 Chapter 1.7 Accessory Connections 1.7.1 Accessory Connector Pin Functions.............................................................1.7-18 1.7.2 Connection Plan for Accessories..................................................................1.7-20 General:
A The following installation suggestions and test procedures are recommended for vehicles with electronic anti-
lock/anti-skid brakes. Refer to your vehicle service manual for your vehicles braking system, or contact your dealer directly. INSTALLATION WARNINGS:
WARNING Disruption of the anti-skid/anti-lock braking system by the radio transmitter may result in unexpected vehicle motion. Motorola recommends the following radio installation precautions and vehicle braking system test procedures to ensure that the radio, when transmitting, does not interfere with the operation of the vehicle braking system. INSTALLATION PRECAUTIONS:
1. Always provide as much distance as possible between the braking modulator unit and the radio, the radio antenna, and associated transmission line. Before installing the radio, determine the location of the brak-
ing modulator unit in the vehicle. Depending on the make and model of the vehicle, the braking modulator unit may be located in the trunk, under the dashboard, in the engine compartment, or in some other cargo area. If you cannot determine the location of the braking modulator unit, refer to the vehicle service man-
ual or contact a dealer for the particular make of the vehicle. If the braking modular unit is located on the left side of the vehicle, install the radio on the right side of the vehicle, and conversely. 2. 3. Route all radio wiring, including the antenna transmission line, as far away as possible from the braking modular unit and associated braking system wiring. 4. Never activate the radio transmitter while the vehicle is in motion and the vehicle trunk lid is open. BRAKING SYSTEM TESTS:
Be sure the following vehicle testing is done in an isolated area. The following procedure checks for the most common types of interference that may be caused by a radio transmitter to vehicle braking system:
1. Run the vehicle engine at idle speed and set the vehicle transmission selector to PARK. Release the brake pedal completely and key the radio transmitter. While NOT speaking into the microphone, verify that there are no unusual effects (visual or audible) to the vehicle lights, or other electrical equipment and accesso-
ries. 2. Repeat Step 1, except do so while speaking into the microphone. 3. Press the vehicle brake pedal slightly; just enough to illuminate the vehicle brake light(s). Then repeat Steps 1 and 2. 4. Press the vehicle brake pedal rmly and repeat Steps 1 and 2. 5. Ensure that there is a minimum of two vehicle lengths between the front of the vehicle and any object in the vehicles forward path. Then, set the vehicle transmission selector to DRIVE. Press the brake pedal just far enough to stop the vehicle motion completely. Key the radio transmitter. Verify that the vehicle does not start to move while NOT speaking into the microphone. 6. Repeat Step 5, except do so while speaking into the microphone. 7. Release the brake pedal completely and accelerate the vehicle to a speed between 15 and 25 miles (25 and 40 kilometers) per hour. Ensure that a minimum of two vehicle lengths is maintained between the front of the vehicle and any object in the vehicles forward path. Have another person key the radio transmitter, and verify that the vehicle can be braked normally to a moderate stop while NOT speaking into the micro-
phone. 8. Repeat Step 7, except do so while speaking into the microphone. 9. Release the brake pedal completely and accelerate the vehicle to a speed of 20 miles (30 kilometers) per hour. Ensure that a minimum of two vehicle lengths is maintained between the front of the vehicle and any object in the vehicles forward path. Have another person key the radio transmitter, and verify that the vehi-
cle can be braked properly to a sudden (panic) stop while NOT speaking into the microphone. 10. Repeat Step 9, except do so while speaking into the microphone. 11. Repeat Steps 9 and 10, except use a vehicle speed of 30 miles (50 kilometers) per hour. 6881092C58-O B
WARNING For radios installed in vehicles fuelled by liqueed petroleum gas, refer to the (U. S.) National Fire Protection Association standard, NFPA 58, for storage, handling, and/or container information. For a copy of the LP-gas standard, NFPA 58, contact the National re Protection Association, One Battery Park, Quincy, MA,. 6881092C58-O Chapter 1.1 Safety Information 1.1-1 Read this information before using your radio. SAFE AND EFFICIENT OPERATION OF MOTOROLA TWO-WAY RADIOS This document provides information and instructions for the safe and efcient operation of Motorola Portable and Mobile Two-Way Radios. The information provided in this document supersedes the general safety information contained in user guides published prior to 1 January 1998. For information regarding radio use in hazardous areas, please refer to the Factory Mutual (FM) approval manual supplement. EXPOSURE TO RADIO FREQUENCY ENERGY Your Motorola Two-Way Radio, which generates and radiates radio frequency (RF) electromagnetic energy (EME), is designed to comply with the following National and International Standards and Guidelines regarding exposure of human beings to radio frequency electromagnetic energy:
l l l l l Federal Communications Commission Report and Order No. FCC 96-326 (August 1996) American National Standards Institute (C95.1 - 1992) National Council on Radiation Protection and Measurements (NCRP-1986) International Commission on Non-Ionizing Radiation Protection (ICNRP- 1986) European Committee for Electrotechnical Standardization (CENELEC):
- ENV 50166-1 1995 E
- ENV 50166-2 1995 E
- Proceedings of SC211/B 1996 Human exposure to electromagnetic elds Low frequency (0 Hz to 10 kHz) Human exposure to electromagnetic elds High frequency (10 kHz to 300 GHz) Safety Considerations for Human Exposure to EMFs from Mobile Telecommunication Equipment
(MTE) in the Frequency Range 30MHz - 6 GHz.
(EMF - Electro-Magnetic Fields) To assure optimal radio performance and to ensure that your exposure to radio frequency electromagnetic energy is within the guidelines in the above standards, always adhere to the following procedures:
PORTABLE RADIO OPERATION AND EME EXPOSURE 2.5 to 5.0 cm
(1 to 2 in.) l l When transmitting with a portable radio, hold radio in a vertical position with the microphone 2.5 to 5.0 centimeters (one to two inches) away from the mouth. Keep antenna at least 2.5 centimeters (one inch) from your head or body when transmitting. If you wear a portable two-way radio on your body, ensure that the antenna is at least 2.5 centimeters (one inch) from the body when transmitting. 1.1-2 ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY NOTE Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inade-
quately shielded, designed, or alternately congured for electromagnetic compatibility. l l To avoid electromagnetic interference and/or compatibility conicts, turn off your radio in any facility where posted notices instruct you to do so. Hospital or health facilities may be using equipment that is sensitive to external RF energy. When instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions. OPERATIONAL WARNINGS Vehicles with an air bag
WARNING: Do not place a portable radio in the area over an air bag or in the air bag deploy-
ment area. Air bags inate with great force. If a portable radio is placed in the air bag deploy-
ment area and the air bag inates, the radio may be propelled with great force and cause serious injury to occupants of vehicle. Potentially explosive atmospheres
WARNING: Turn off your Two-Way radio when you are in any area with a potentially explosive atmosphere, unless it is a radio type especially qualied for use in such areas (e.g. FM or Cenelec approved). Sparks in a potentially explosive atmosphere can cause an explosion or re resulting in bodily injury or even death. Batteries WARNING: Do not replace or recharge batteries in a potentially explosive atmosphere. Con-
tact sparking may occur while installing or removing batteries and cause an explosion.
Blasting caps and areas
NOTE WARNING:
near electrical blasting caps. In a signs and instructions. To avoid possible interference with blasting operations, turn off your radio when you are
, obey all turn off two-way radio or in areas posted blasting area The areas with potentially explosive atmospheres referred to above include fuelling areas such as:
below decks on boats; fuel or chemical transfer or storage facilities; areas where the air contains chemicals or particles, such as grain, dust or metal powders; and any other area where you would normally be advised to turn off your vehicle engine. Areas with potentially explosive atmospheres are often but not always posted. OPERATIONAL CAUTIONS Damaged antennas
CAUTION: Do not use any portable two-way radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. 1.1-3 Batteries
CAUTION: All batteries can cause property damage and/or bodily injury such as burns if a conductive material such as jewelry, keys or beaded chains touch exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse or other container with metal objects. MOBILE RADIO OPERATION AND EME EXPOSURE To assure optimal radio performance and that human exposure to radio frequency electromagnetic energy is within the guidelines referenced in this document, transmit when people outside the vehicle are at least the minimum distance away from a properly installed, externally-mounted antenna. The table below lists the minimum distance for several different ranges of rated radio power. only Table 1.1-1: Rated Power and Distance Rated Power of Vehicle-Installed Mobile Two-Way Radio Minimum Distance from Transmitting Antenna 7 to 15 Watts 16 to 50 Watts 1 Foot (30.5 Centimeters) 2 Feet (61 Centimeters) More than 50 Watts 3 Feet (91.5 Centimeters) ANTENNA INSTALLATION MOBILE ANTENNAS Recommended mobile antenna installations are limited to metal body vehicles at the center of the roof and center of the trunk deck locations. The antenna installation must additionally be in accordance with:
a. The requirements of the antenna manufacturer/supplier b. Instructions in the Radio Installation Manual FIXED SITE ANTENNAS Mobile radio equipment is sometimes installed at a xed location and operated as a control station or as a xed unit. In such cases the antenna installation must comply with the following requirements in order to assure optimal performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards:
l l l l The antenna must be mounted outside the building. Mount the antenna on a tower if at all possible. If the antenna is to be mounted on a building, then it must be mounted on the roof. As with all xed site antenna installations, it is the responsibility of the licensee to manage the site in accordance with applicable regulatory requirements and may require additional compliance actions, such as site survey measurements, signage, and site access restrictions in order to insure that exposure limits are not exceeded. General Information 1.2-4 Chapter 1.2 Introduction 1.2.1 General Information There are two methods of installing your mobile radio:
1. The standard radio package contains a direct mounting trunnion and power cables. 2. Some models may be mounted in the car radio cut-out (using the required GLN7320 mounting kit, per ISO7736). An accessory connector on the rear of the radio (see Figure 1.5-1) enables you to attach different accessories required for the installation. A ten-pin telephone type connector on the front control head panel (see Figure 1.5-2) provides for the connection of various types of microphones. 1.2.2 Plan the Installation 1. Mount the radio horizontally near the driver, so the driver can easily view, access, and operate the controls and accessories. 2. Ensure that the location is not exposed to dirt and moisture. 3. Verify that there will be sufcient space around the mobile unit for air ow and installation. 4. Check that there is enough routing space for the power cable connector and the antenna coaxial cable. 5. Plan the best place to run connections to minimize pinching, crushing, and overheating of wires and cables. NOTE In a vehicle with an airbag, make sure that the mounting location of the mobile radio, or of any radio accessory, is not in the deployment path of the air bag. Planning the Power Cable Installation 1.3-5 Chapter 1.3 DC Power Cable Installation 1.3.1 Planning the Power Cable Installation
CAUTION: This radio must be operated only in negative ground electrical systems. Operating the radio on a positive ground system will cause the cable fuse to short-circuit. Check the vehicle ground polarity before you begin the installation. The 10 foot (3 meter) DC power cable shipped with the radio should be long enough to be installed in most vehicles. Take the following precautions before you begin:
l l Whenever possible, avoid routing the cable above the catalytic converter. Use grommets whenever a cable has to pass through a hole in a metal panel. The following table lists power cables available for this radio:
Table 1.3-1: Power Cables Number Description Rating HKN4137 HKN4191 12V Low power cable to battery 1-25W; 15A fuse; 14 AWG 3m High Power Cable to battery 25-45W; 20A fuse; 12 AWG 3m 1.3.2 Power Cable Installation Procedure Begin the power cable installation as follows:
1. Determine a routing plan, keeping in mind where the radio is to be mounted. CAUTION: Improper handling with the power cable may cause shortages to ground. Ensure that during radio installation the power cable fuse is removed."
2. Locate an existing hole with grommet in the vehicle re wall, or use a 3/8-inch (9.5 mm) bit to drill an access hole in the re wall. Install a grommet with a 3/16-inch (4.9 mm) inside diameter into the hole to protect the power cable. CAUTION: Be very careful not to damage existing wires.
3. From inside the vehicle, feed the red and black leads (without the lugs attached) through the access hole and into the engine compartment. (See Figure 1.3-1) 1.3-6 Power Cable Installation Procedure To Radio Black Lead Red Lead Firewall Grommet Engine Compartment FL08302460 Figure 1.3-1. Power Cable Routing into the Engine Compartment 4. Connect the black lead of the power cable to the nearest vehicle chassis ground point (using the provided ring lug if necessary). Shorten the black lead to remove any excess cable. (See Figure 1.3-2.) NOTE Locate a good vehicle ground point. The vehicle frame provides the best ground. Optimum radio performance can only be achieved with a very low resistance ground connection. Verify that the connections between the battery negative terminal, vehicle chassis, and engine block have low resistance. 5. Place the fuse holder close to the battery. Ensure that it is not near any hot engine component. Mount the fuse holder using its mounting hole and dress the wires as required. 6. Insert the stripped end of the red lead of the fuse holder into the ring lug hole and crimp it. Connect the fuse holder red adapter lead plug to the mating receptacle on the red lead of the power cable. (See Figure 1.3-2.) 7. Connect the power cable black lead directly to the vehicle chassis ground. 8. Connect the red lead ring lug from the fuse holder to the positive (+) battery terminal. Make sure the adapter cable is connected to the main power cable red lead. 9. Carefully check that all connections are proper. Insert the fuse into the fuse holder and close the cover. (See Figure 1.3-2.) NOTE Failure to mount the red lead of the power cable kit directly to the battery may result in severe alternator whine interference. Power Cable Installation Procedure 1.3-7 Fuse Molded In-Line Fuse Holder Adapter Red Lead Firewall Red Lead Mounting Hole Black Lead Engine Compartment Cover Red Lead Ring Lugs To Vehicle Chassis Ground To Battery (+) FL08302470 Figure 1.3-2. Power Cable Assembly 1.4-8 Planning the Mounting Trunnion Installation Chapter 1.4 Trunnion Installation 1.4.1 Planning the Mounting Trunnion Installation The standard mounting trunnion allows the radio to be mounted to a variety of surfaces. 1. Ensure the surface can support the weight of the radio. 2. Although the trunnion can be mounted to a plastic dashboard, it is recommended that the mounting screws be located so they penetrate the supporting metal frame of the dashboard. NOTE For Low Band radios only: Motorola recommends the use of a Three-point Mounting Trunnion (Motorola part number RLN4774). 1.4.2 Trunnion Installation Procedure 1. Select either the transmission hump or an open underneath portion of the dash to mount your radio. (See Figure 1.5-2.) When mounting the trunnion on the transmission hump, be careful that the transmission housing is not affected. 2. Use the trunnion mounting bracket as a template to mark the hole positions on the mounting surface. Use the innermost three holes for a curved mounting surface, such as the transmission hump, and the three outermost holes for a at surface such as under the dash. 3. Center-punch the spots you marked and use a 5/32-inch (4 mm) bit to drill a hole at each location. 4. Secure the trunnion mounting bracket to the mounting surface with the three self-tapping screws provided. (See Figure 1.5-2.) 5. Slide the radio into the trunnion. Secure the radio with the two thumb screws provided. (See Figure 1.4-1.) Thumb Screw Thumb Screw Trunnion Figure 1.4-1. Radio into Trunnion Control Head Mounting Position 1.4-9 1.4.3 Control Head Mounting Position The control head is designed to be removed from the housing and turned to any position within a 180 radius. This provides multiple mounting options for the radio. For example, the radio may be mounted on either side of the vehicle transmission tunnel to facilitate the safest and most ergonomically ideal position. The control head may then be turned to provide the most convenient access. To reposition the control head:
1. Insert a small at blade screwdriver, or similar instrument, in the recess between the control head and the radio housing. 2. Press until the control head releases. Repeat the process on the opposite side of the radio. 3. Pull the control head away while ensuring that the ex connector remains attached. 4. Rotate the control head, and fold the ex circuit to align it to the new position. 5. Push the control head into the housing until the protruding tabs snap into place.
CAUTION: The contact surface of the ex circuit should be facing the printed circuit board. 1.5-10 Mobile Radio Operation and EME Exposure Chapter 1.5 Antenna Installation 1.5.1 Mobile Radio Operation and EME Exposure Observe the following caution and electromagnetic energy exposure (EME) statements when installing antennas:
CAUTION: Use caution when installing antennas with mobile radio equipment using transmitter power in excess of 7 Watts. NOTE For low-power mobile radios (7 Watts, or less), there are no antenna type or installation restrictions. To assure optimal radio performance and that human exposure to radio frequency electromagnetic energy is within the guidelines referenced in this document, transmit when people outside the vehicle are at least the minimum distance away from a properly installed, externally-mounted antenna. The table below lists the minimum distance for several different ranges of rated radio power. only Table 1.5-1: Rated Power and Distance Rated Power of Vehicle-Installed Mobile Two-Way Radio Minimum Distance from Transmitting Antenna 7 to 15 Watts 16 to 50 Watts 1 Foot (30.5 Centimeters) 2 Feet (61 Centimeters) More than 50 Watts 3 Feet (91.5 Centimeters) 1.5.2 Selecting an Antenna Site 1.5.3 Mobile Antennas Recommended mobile antenna installations are limited to metal body vehicles at the center of the roof and center of the trunk deck locations. 1. to the vehicle and in accordance with:
Install the vehicle antenna a. The requirements of the antenna manufacturer/supplier b. Instructions in the radio installation manual. external 2. The best mounting location for the antenna is in the center of a large, at conductive surface. In almost all vehicles, mounting the antenna in the center of the roof will satisfy these requirements. A good alternate location is in the center of the trunk lid. If you use the trunk lid, ensure that the trunk lid is grounded by connecting grounding straps between the trunk lid and the vehicle chassis. 3. Ensure the antenna cable can be easily routed to the radio. Ensure that the antenna cable is routed separately and not in parallel to any other vehicle wiring or mobile radio cable wiring. Antenna Installation Procedure 1.5-11 4. Check the antenna location for any electrical interference. NOTE Any two metal pieces rubbing against each other (such as seat springs, shift levers, trunk and hood lids, exhaust pipes, etc.) in close proximity to the antenna can cause severe receiver interference. 5. If the vehicle is equipped with an electronic anti-lock braking system (ABS), and the antenna will be trunked mounted, then install the antenna on the side opposite to the braking modulator box. This minimizes radio interference to the modulator box from the radio. 6. Make sure the mobile radio antenna is installed at least one foot (30.48 cm) away from any other antenna on the vehicle. 1.5.4 Fixed Site Antennas Mobile radio equipment is sometimes installed at a xed location and operated as a control station or as a xed unit. In such cases the antenna installation must comply with the following requirements in order to assure optimal performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards:
l l l l The antenna must be mounted outside the building. Mount the antenna on a tower if at all possible. If the antenna is to be mounted on a building, then it must be mounted on the roof. As with all xed site antenna installations, it is the responsibility of the licensee to manage the site in accordance with applicable regulatory requirements and may require additional compliance actions, such as site survey measurements, signage, and site access restrictions in order to insure that exposure limits are not exceeded. 1.5.5 Antenna Installation Procedure 1. Mount the antenna according to the instructions provided with the antenna kit. Run the coaxial cable to the radio mounting location. If necessary, cut off the excess cable and install the cable connector. 2. Connect the antenna cable connector to the radio antenna connector on the rear of the radio.
(See Figure 1.5-1.) Accessory Connector Antenna Connector To Battery
+ via Fuse F1 (red) Power Connector Vehicle Chassis Ground
(black) FL0830249O Figure 1.5-1. Connections to the Back of Radio 1.5-12 Completing the Installation 1.5.6 Completing the Installation 1. Mount the microphone clip to a convenient spot near your radio. 2. Your microphone has a telephone-type connector at the end of its cord. Plug the microphone into the control head connector. 3. To complete your radio installation, plug the power cable into the radio power connector. (See Figure 1.5-1.) Completing the Installation 1.5-13 TRANSMISSION HUMP MOUNTING Tab Thumb Screw
(2) Tab Mounting Surface Tab Trunnion Mounting Bracket 1.12"
(28mm) 1.84"
(46mm) 1.84"
(46mm) 2.92"
(73mm) 2.92"
(73mm) BELOW DASH MOUNTING Mounting Surface Trunnion Mounting Bracket Sheet Metal Screws Thumb Screw
(2) Figure 1.5-2. Transmission Hump Mounting (Top) and Below Dash Mounting (Bottom) FL0830250O 1.6-14 Radio Mounting in Dashboard Chapter 1.6 Installation Options 1.6.1 Radio Mounting in Dashboard To install the radio in an automotive dashboard:
1. Open the radio cutout in the dashboard and, if necessary, enlarge it to the dimensions shown in Figure 1.6-1. 2. Insert the mounting frame into the cutout and bend the six tabs (see Figure 1.6-2) to hold it in place. Press the bezel onto the mounting frame. 3. Slide the radio into the mounting frame. 4. Make the necessary connections to the radio for power, antenna, and accessory connector as shown in Figure 1.5-1. Mounting Frame 52mm
(2") 180mm
(7-1/4") Bezel 175mm
(7") FL08302510 Figure 1.6-1. Mounting the radio into the dashboard External Speaker Installation 1.6-15 Tabs (6) Mounting Frame Figure 1.6-2. Mounting Frame Detail FL0830252O 1.6.2 External Speaker Installation 1. Remove the speaker from the trunnion bracket by loosening the two wing screws. 2. Choose a place to mount the speaker. 3. Use the trunnion bracket as a template to mark the locations of the three mounting holes. 4. Centerpunch and drill a 5/32-inch (4 mm) diameter hole at each location. 5. Mount the trunnion bracket with the screws supplied. (See Figure 1.6-3.) 6. 7. Insert the speaker into the trunnion bracket and tighten the two wing screws. Insert the external speaker accessory plug into the accessory connector of the radio. Dashboard Firewall Console or Floor Dashboard 0.157'' (0.399cm) Diameter Firewall Trunnion Bracket Trunnion Bracket To Firewall Mounting or 10-16 x 5/8''
Self-Tapping Screw FL0830253O Figure 1.6-3. Mounting the Speaker Under the Dashboard 1.6-16 Remote Control Head Installation 1.6.3 Remote Control Head Installation 1.6.3.1Removing the Front Housing 1. Remove the Control Head from the Transceiver by inserting the dismantling tool (Motorola part number 6686119B01) in the recess between the Control Head and the Transceiver (see Figure1.6-4). 2. Split the Control Head into Front and Back housings by inserting the dismantling tool in the recess between them. NOTE 1. To minimize cosmetic damage disassemble from the bottom side,
(label side). 2. The Controlhead Back Housing is not required for remote mounting. 3. Remove the ex from the Control Head PCB only. 1.6.3.2Assembling the Remote Front Housing 1. Connect the ex from the Transceiver to the Remote Front PCB. NOTE For correct orientation of the ex, align the O on the ex with the O on the PCB. 2. Press the Remote Front Housing onto the Transceiver chassis until the four chassis tabs snap into place. 1.6.3.3Assembling the Remote Back Housing 1. Connect the ex from the Remote Back to the Control Head PCB connector
(the connector ex was removed in 1.6.3.1.3 above). 2. Align the speaker with the speaker support. 3. Press the Control Head onto the Remote Back Housing until ALL the tabs snap into place (four tabs on the RLN4801, six on the RLN4802). 1.6.3.4Installing the Remote Control Head 1. Position the Remote Mount Bracket in the desired location and mark the positions of the mounting holes 2. Centerpunch the marked spots and drill 4mm holes at each spot. 3. Fix the Remote Mount Bracket in position using the supplied screws. 4. Route the Remote Cable (Table 1.6-1:) as required, feeding it through the bracket
(a 20mm hole is required for the cable plug). 5. Push the cable plug into the Remote Front and Back Housing until it snaps into place. 6. Snap the assembly into the bracket. 7. Adjust the assembly as required then x it in position with the wing screws supplied.\
Remote Control Head Installation 1.6-17 1 2 3 4 5 6 7 8 9 Figure 1.6-4. Remote Front and Back Housings FL0830254O Table 1.6-1: Associated Components Item Description Part Number 1,8 2,9 3 4 5 6 7 Flex (two per kit) Remote PCB (two per kit) Transceiver Front Housing Cable Kit 3M Cable Kit 5M Cable Kit 7M Wing screws Remote Bracket Remote Back Housing Primary Remote Back Housing Practical/Versatile O-Ring Controlhead 8486127B01 GLN7362A 1564270B01 RKN4077 RKN4078 RKN4079 0305760W02 0764275B01 1564268B01 1564269B01 3202620Y01 1.7-18 Accessory Connector Pin Functions Chapter 1.7 Accessory Connections 1.7.1 Accessory Connector Pin Functions This section gives a description of the accessory connector pin functions. CAUTION: The accessory connections shown are not compatible to some other models of Motorola radios. Check the appropriate accessory or technical manual for further information.
Table 1.7-1: Connector Pin Functions Pin Function Description 1 2 3 4 5 6 7 8 9 External Speaker -
External Mic Audio Digital In 1 Digital Out 2 Speaker - and Speaker + (Pin 16) are used to connect an external speaker. The audio PA is a bridge amplier with a minimum load resistance of 3.2 ohms (W
). The internal speaker can be disabled by removing the control head. Disconnect the internal speaker and assemble the control head back to the radio. External or Emergency Mic depends on dealer programming. This microphone signal is independent of the microphone signal on the microphone connector. The nominal input level is 80mV for 60% deviation. The DC impedance is 660 ohms and the AC impedance is 560. This is a digital input only and the primary use for this pin is external PTT.
(See Note 1). This is a digital output only and the primary use for this pin is as an external alarm out-
put (See Note 3). Flat_TX_Audio
(NPD Data Out) This input is intended for injecting signals into the transmit path that should not be l-
tered; for example, the analog output of a modem. The nominal input level is 150mVrms for 60% deviation. The impedance is greater than 25kohms. Digital In 3 This is a digital input only. Function depends on dealer programming. (See Note 4). Ground Used as ground for both analog and digital signals Digital In/Out 4 This is a digital input/output depending on dealer programming. (See Note 1, 2). Digital In 5 with Wakeup Emer-
gency This is a digital input only. Emergency can be enabled via the CPS. To activate, this line must be connected to ground; this will turn on the radio. The CPS details which functions may be assigned to this pin by the codeplug. 10 Ignition Detect Connecting this line to the ignition line of the vehicle will automatically turn the radio on when the ignition of the vehicle is turned on. 11 Receiver Audio There are two possible outputs: (1) Discriminator Audio; and (2) Continuous ltered RX audio. The nominal output level for Discriminator Audio is 330m Vrms at 60% devi-
ation and for Filtered Audio 600m Vrms at 60% deviation at 1kHz. Function depends on dealer programming. 12 Digital In/Out 7 This digital input/output function depends on dealer programming. Accessory Connector Pin Functions 1.7-19 Table 1.7-1: Connector Pin Functions Pin Function Description 13 14 15 16 17 18 19 20 Switched Battery Voltage This voltage is available when the radio is switched on. The maximum current is 1A. Digital In/Out 8 This is a digital input/output depending on dealer programming. (See Note 1, 2). RSSI External Speaker +
Bus +
Boot Control This is an analog output which indicates the strength of the received signal. Positive output of radios audio PA (see Pin 1). This pin is used for ashing and for programming the radio. To enter Boot Mode this line must be connected to ground when the radio is switched on. Reserved Reserved Reserved. Reserved. Note 1:
Note 2:
Note 3:
Note 4:
Internal Pull Up Resistor to +5V. Digital Input 4.7 kW Maximum Input Voltage accepted as Low = 0.6V Minimum Input Voltage accepted as High = 3.0V Internal Pull Up Resistor to +5V Digital Output 4.7kW Maximum Current when Output Low = 10mA Maximum Voltage when Output Low = 0.5V @ 10mA Internal Pull Up Resistor to continuous B+
High Current Digital Output 4.7kW Maximum Current when Output Low = 200mA Maximum Voltage when Output Low = 1.7V @200mA Digital Input 10kohms Internal Pull Up Resistor to +5V Maximum Input Voltage accepted as Low = 0.6V Minimum Input Voltage accepted as High = 3V 1.7-20 Connection Plan for Accessories 1.7.2 Connection Plan for Accessories
CAUTION: The accessory connections shown are not compatible to some other models of Motorola radios. Check the appropriate accessory or technical manual for further information.
+12V 86 85
+12V 86 85 Alternative 4 Alternative 4 87 30 Alarm Relay
+12V 87 30 Alarm Relay
+12V CAUTION: DO NOT short pin 16 or 1 on the accessory connector to ground; this may damage the radio. Accessory Connector Antenna Connector To Battery
+ via Fuse F1 (red) Power Connector Vehicle Chassis Ground
(black) Figure 1.7-1. Accessory Connector CAUTION: Ensure correct position of the accessory connector.
Section 2 Reducing Noise Interference in Mobile Two-Way Radio Installations i Chapter 2.1 Introduction 2.1.1 Noise Sources................................................................................................ 2.1-1 2.1.2 Radiated Noise .............................................................................................. 2.1-1 2.1.3 Conducted Noise ........................................................................................... 2.1-2 2.1.4 Induced Noise ................................................................................................ 2.1-2 Chapter 2.2 Operation of a Conventional Ignition System 2.2.1 Introduction .................................................................................................... 2.2-3 2.2.2 Sources of Ignition Interference ..................................................................... 2.2-3 Chapter 2.3 Detection of Noise Sources 2.3.1 Noise Detection Procedure ............................................................................ 2.3-5 2.3.2 Sources of Noise............................................................................................ 2.3-7 Chapter 2.4 Noise Reduction Techniques 2.4.1 General .......................................................................................................... 2.4-8 2.4.2 Ignition System Interference .......................................................................... 2.4-8 2.4.2.1 Engine Maintenance and Tune-Up................................................... 2.4-8 2.4.2.2 Available Noise Reduction Kits......................................................... 2.4-8 2.4.2.3 Ignition Coil Interference................................................................... 2.4-9 2.4.2.4 Distributor Interference ..................................................................... 2.4-9 2.4.2.5 Battery Connections ......................................................................... 2.4-9 2.4.3 Alternator/Generator Whine ......................................................................... 2.4-10 2.4.4 Voltage Regulator Noise .............................................................................. 2.4-11 2.4.5 Hood and Trunk Lid Noise ........................................................................... 2.4-11 2.4.6 Other Electrical Noises ................................................................................ 2.4-12 2.4.7 Wheel Static................................................................................................. 2.4-12 2.4.8 Ground Bonding........................................................................................... 2.4-12 Noise Sources Chapter 2.1 Introduction 2.1-1 Electrical noise generated by the electrical system of a vehicle, as well as local ambient noise, can interfere with normal operation of mobile radios. Satisfactory operation of a mobile radio may require slight or heavy noise reduction, depending upon the relative strength of the radio signal, and upon the ability of the radio to reject undesired noise. These requirements vary from one vehicle to another, depending upon the vehicle type and required coverage area. When operating in a strong signal area, a certain amount of noise interference can be tolerated. In weak signal areas, however, noise reduction becomes very important. As a rule of thumb, noise levels create greatest interference in the 25-50MHz band and reduce with increasing frequency. Before attempting any noise reduction procedures, determine the noise source(s). Then, follow a logical, systematic method of elimination until the interference is eliminated or reduced to an acceptable level.
CAUTION: Do not add interference elimination equipment to vehicles equipped with electronic ignition systems before obtaining advice from the vehicle manufacturer. Addition of some noise suppression components may interfere with proper operation of electronic ignition systems and could seriously damage them. Care and patience must be exercised in locating and eliminating noise sources. There may be several sources of noise, each slightly stronger or weaker than the other. Elimination of one source may seem ineffective because another noise source remains active at a barely discernible difference in level. Consult a service manual for the vehicle to determine what noise reduction provisions the manufacturer applies when AM, AM/FM, or CB radios are installed as original equipment. These radios are also subject to electrical noise interference, and the manufacturer may install noise suppression components only upon those vehicles which require radio equipment at the time of manufacture. These noise suppression components should be added in any rst attempt to suppress noise. 2.1.1 Noise Sources The three major noise sources affecting mobile radio systems are: (1) radiated noise, (2) conducted noise, and (3) induced noise. (See Figure 2.1-1 for typical vehicular noise sources.) 2.1.2 Radiated Noise Radiated noise enters the radio through the antenna along with the desired signal and can block or degrade desired communication. It can be generated by power lines, uorescent lights, or by electrical discharges from static build-up, ignition systems, or electrical motors. Radiated noise is the most common cause of mobile radio interference. When a spark discharge or arc takes place through air, energy is radiated at frequencies from a few kilohertz to hundreds of megahertz. This spurious radiation may have some energy radiated at a frequency near or even identical to the desired radio signal. The standard receiver may be unable to distinguish between the two signals (desired and noise). Therefore they both enter the receiver, resulting in degradation of the desired signal. 2.1-2 Conducted Noise It is impractical to prevent all arcing in the standard vehicle electrical system. In an 8-cylinder engine running at 2,000 RPM, arcing occurs across the spark plugs at a rate of 8,000 sparks per minute or 133 sparks per second. Electrical motors and generators also produce arcs. Inadequate Terminal or Fuse Block Filtering Radiated Noise Pick-up Antenna Ground or Location Windshield Wiper Motor Heater Air Conditioner Blower Electric Windows Motors Hood Static Power Seat Motor Electric Fuel Pump Wheel Static Voltage Regulator Distributor Ignition Coil Alternator or Generator Spark Plug Wires Spark Plugs Idle Stop Solenoid FL0830260-O Figure 2.1-1. Noise Sources 2.1.3 Conducted Noise Conducted noise enters the radio through the points where the radio is attached to the vehicles electrical system such as battery cables, ignition switch, chassis ground etc. It can be generated by electrical transients, electrical motors, poor grounding points, or inadequate electrical system ltering
(from alternators, generators, voltage regulators, or weak batteries). Conducted noise can degrade both transmit and receive performance of a mobile radio. 2.1.4 Induced Noise Induced noise enters the radio through the proximity of radio wiring to other wiring in the vehicle. Electrical currents through the standard vehicular wiring can induce undesirable noise signals into the radio cabling. Communication is degraded simply because the wiring provides a transformer-type coupling action without any actual physical connection. Induced noise can degrade both transmit and receive performance of a mobile radio. Introduction 2.2-3 Chapter 2.2 Operation of a Conventional Ignition System 2.2.1 Introduction To effectively reduce ignition interference in a vehicle, it is well to understand the operation of an automobile ignition system. Ignition is necessary in a gasoline engine to ignite the gasoline vapor and the air mixture in its cylinders. The system is made up of the battery, distributor, breaker points, coil, condenser, and spark plugs. The battery is the only electrical source of power in an automobile, so the lower battery voltage must be stepped up to the high voltage necessary to arc across the spark plug electrodes. This arc ignites the gas mixture. 2.2.2 Sources of Ignition Interference In the conventional ignition system (Figure 2.2-1) a mechanical circuit breaker (the cam and points in the distributor) opens the primary circuit of the ignition coil, and high voltage is developed at the secondary. This high voltage is synchronized and applied to each spark plug by the distributor. HV Lead Ignition Coil Breaker Points Ignition Switch Battery Cam Condenser Distributor Spark plug leads Spark Plugs Breaker Points Ignition Switch Battery Cam Rotor Gap Ignition Coil Stray Capacitance Condenser Lead Inductance Spark Plug Gap FL0830261-O Figure 2.2-1. Typical Vehicular Ignition System, Simplied Schematic Diagram 2.2-4 Sources of Ignition Interference The battery is connected to the primary winding of the coil through the ignition switch. The primary circuit is returned to the battery through the breaker points, which are bypassed by the condenser. The points are normally closed. As the cam shaft is rotated by the engine, its lobes or corners open and close the points in proper synchronization with the piston in each cylinder. With the ignition switch on and the breaker points closed, coil primary current builds up at a rate determined by the coil inductance. When the breaker points open, primary current decreases and, by self-induction, an electromotive force is induced in the primary which is many times greater than the battery voltage. The high voltage inducted in the coil secondary causes a spark across the distributor rotor-to-spark plug wire gap and then across the spark plug gap for a short interval of time when the breaker points open. The condenser reduces arcing of the points. The secondary circuit of the ignition coil, including the distributor rotor gap and the spark gap, is the main source of ignition interference. The lead inductance and stray capacitance provide a tuned circuit. Because the discharge of the circuit is through a low resistance (ionized spark gap), the circuit tends to oscillate. The frequency and amplitude of oscillation vary as current changes in the spark gap. Noise Detection Procedure 2.3-5 Chapter 2.3 Detection of Noise Sources 2.3.1 Noise Detection Procedure Detection of offending noise sources is the heart of noise suppression because, after the noise source is identied, the solution becomes obvious. A logical methodical procedure is basic to the effective noise suppression. Use your available equipment to best advantage. A pick-up loop, about one inch in diameter, can be connected to a portable CB radio or a mobile radio being operated at a frequency similar to the installed radio frequency but from an isolated supply voltage. The pick-up loop can be moved throughout the vehicle with the radio used as a radiated noise detector. Be sure the pick-up loop has sufcient insulation to prevent the input of the radio from coming into direct contact with high voltage points in the vehicle ignition system. A non-polarized bypass capacitor, which has alligator clips rmly attached, can be used on a trial-
and-error basis to locate wiring which needs additional ltering. Keep capacitor lead lengths short for best suppression. Ceramic disc capacitors are not as suitable or effective as automotive coaxial capacitors. (See Figures 2.3-1 and 2.3-2 for part numbers.) Ignition Switch Battery 2 1 Ignition Coil 3 Resistive Wire
(Note 2) Breaker Points Distributor Resistor Spark Plugs
(Note 2) Notes:
1. Noise reduction can only be achieved if components are grounded properly. 2. Items not supplied in kit. See auto parts dealer. Reference Number 1 2 3
Quantity 1 1 1 1 Motorola Part Number 1V839913 8C82571B02 30A502396 1V80782A52 Description FL0830262-O Lead & Lug Assembly Capacitor, Coaxial (0.1F, 100V) Ignition Coil Suppressor Cable Hood Wipers (2) and Mounting Hardware Kit (not illustrated). Figure 2.3-1. TLN8845 Noise Reduction Kit for Alternator-Equipped Vehicles 2.3-6 Ignition Switch Battery Noise Detection Procedure 3 1 Ignition Coil 6 Resistive Wire
(Note 2) Breaker Points Distributor Resistor Spark Plugs
(Note 2) Notes:
1. Noise reduction can only be achieved if components are grounded properly. Be sure that all the capacitors and the generator filed suppressor assembly are grounded properly. This may require bonding straps for proper bypass capacitor effectiveness. 2. Items not supplied in kit. See auto parts dealer. Generator 2 4 Armature 5 Field Common Ground To Battery 4 4 1 1 Voltage Regulator ARM FLD BAT To Generator Field FL0830263-O Reference Number Quantity Motorola Part Number Description 1 2 3 4 5 6
3 1 1 3 1 1 1 1V839913 1V80700A88 8C82571B02 8C82571B01 1V80700A89 30A502396 1V80700A91 Lead & Lug Assembly Lead & Lug Assembly Capacitor, Coaxial (0.1F, 100V) Capacitor, Coaxial (0.5F, 100V) Generator Field Suppressor Assembly Ignition Coil Suppressor Cable Hood Wipers (2) and Mounting Hardware Kit (not illustrated). Figure 2.3-2. TLN6252 Noise Reduction Kit for Generator-Equipped Vehicles Sources of Noise 2.3.2 Sources of Noise 2.3-7 Some interference is due to geographic location. This interference does not need to be eliminated since it is possible for the vehicle to be moved away from the interfering noise source. Noise from power lines, uorescent lights, and other vehicles (emitting high levels of radiated noise) are examples of noise which depends upon location. Make certain that you are not attempting to suppress noise in a vehicle while it is in a noisy location. If you suspect that your location is noisy, simply turn off everything in the vehicle except the radio and listen to the remaining ambient noise. If the noise level is objectionable, you may have to noise suppress the vehicle during a less noisy time of day or in a different, quieter location. Check the installed radio for conducted and inducted noise by using an unmodulated signal generator to supply a clean RF signal through a coaxial cable directly to the antenna connector on the radio set. This should prevent radiated noise from entering the receiver and masking conducted and induced noise. Make certain that the signal generator is not microphonic and is placed away from the noise of the engine and exhaust. Operate the controls for fans, blowers, power windows, headlamps, turn signals, windshield wipers, and other electrical accessories. Listen for the presence of noise in the received radio signal. This will allow the source of the interference to be determined. Some noise sources cannot be turned on and off at will. These sources will need to be attacked piecemeal on a trial and error basis: alternator whine, voltage regulators, electric fuel pump, and other possible sources. Remember that induced noise can result from radio wiring being too close to other vehicle wiring. This problem is most easily solved by proper cable routing at the time of installation. Radiated noise must be attacked after conducted and induced noise has been satisfactorily suppressed. The vehicle ignition system is usually the primary source of this interference. Antenna placement can be critical in some installations. Remember that static discharge generates static or radiated noise and will probably be generated only when the vehicle is in motion. Since radiated noise interference is most noticeable in weak signal areas, it is suggested that suppression be nalized while listening to a weak on frequency signal. (The squelch should be open so that even marginal signals can be heard.) 2.4-8 General Chapter 2.4 Noise Reduction Techniques 2.4.1 General There are three basic ways to suppress noise. The rst is the addition of resistance in circuits subject to ringing. This method is used for the ignition coil HV cable, spark plug wires, and spark plugs. The second is to lter noise from low voltage wiring using coaxial bypass capacitors. The third is to control static charge build-up using wipers for movable parts such as automobile hoods and trunk lids, or exible bonding leads for xed members. Static in wheels may also be controlled using collector rings. Applications of each of these techniques are discussed below. The vehicle manufacturers service manual also may provide noise suppression information which is valuable in any rst attempt at noise suppression. 2.4.2 Ignition System Interference 2.4.2.1 Engine Maintenance and Tune-Up The most important step in reducing ignition noise is insuring that the engine is in proper tune. Pay particular attention to the following points if the noise interference from the ignition system is severe:
1. Be sure the spark plugs distributor points, and condenser are in good condition. 2. Be sure ignition timing is properly adjusted. 3. Be sure the distributor cap and rotor are in good condition. They should be replaced at least every 30,000 miles. 4. Be sure that spark plug wires make good, solid contact at each end and are routed as far as possible from low voltage leads. 5. Many late-model automobiles are equipped with a shield over the distributor points. Check to see that this shield is properly positioned and securely attached. 2.4.2.2 Available Noise Reduction Kits Motorola offers two noise reduction kits: Model TLN8845 for alternator-equipped vehicles; Model TLN6252 for generator-equipped vehicles. These kits are for suppression of noise in the primary and secondary of the ignition coil and for bleeding of static charges on the hood. The TLN6252 also is used to suppress noise from the generator and voltage regulator. Figures 2.3-1 and 2.3-2 show the contents of the kits and their usage. Motorola also offers wheel static collectors (Motorola Part No. 1K534254-regular type and 1K563173-
small type). Use of these items are described in section 2.4.7 Wheel Static on page 12. Most auto parts dealers can supply 0.05 F bypass capacitors (condensers), resistive ignition wires, and resistor spark plugs. The type of spark suppression used in noise reduction should always be in accordance with the recommendations of the vehicle manufacturer, that is, if spark plugs are to be replaced with built-in suppressor types, they should be in the proper heat ranges and thread sizes for the particular engine. In each ignition system, there is a maximum amount of resistance that may be connected between the distributor and a spark plug. If resistance-type ignition wire is used, the length of each wire must be limited so that its resistance does not exceed the allowable maximum. Ignition System Interference 2.4-9 2.4.2.3 Ignition Coil Interference This type of interference is characterized by a popping sound which is most noticeable when the engine is running slowly. To suppress the noise, connect a 0.1 F coaxial capacitor (Motorola Part No. 8C82571B02) from the battery side of the ignition coil to vehicle ground (see Figure 2.4-1). This keeps the distributor noise from being conducted through the battery lead into the electrical system of the vehicle. Note that some electronic ignition systems do not route the battery lead to the ignition coil;
proper operation of the ignition system can be impaired if the input terminal is bypassed. Step 3. Connect wire lead to capacitor using lockwasher and nut. Step 4. Connect capacitor lead to battery post. Step 1. Mount Capacitor
(0.1F Coaxial Type) to vehicle chassis using lockwasher and self-tapping screw. Step 2. Disconnect wire (dashed) from battery post and connect to capacitor using lockwasher and nut. From distributor Distributor Post Battery Post Figure 2.4-1. Ignition Coil Noise Suppression FL0830264-O 2.4.2.4 Distributor Interference This type of interference is characterized by popping sounds which are present at all engine speeds. It is caused by sparking between the rotor and the distributor cap inserts as the rotor turns. To suppress this noise, use resistance ignition wire to connect the ignition coil to the distributor cap. 2.4.2.5 Battery Connections The radio set power cable can pick up noise generated in the vehicle. This can be minimized by connecting the power cable directly to the battery instead of the fuse block. The battery acts like a large capacitor (about one Farad for a 50 amp/hour battery), which bypasses induced noise. The battery ground lead should be securely bonded to the vehicle frame. Undesirable parallel ground currents can be minimized by using the vehicle frame as a common ground point. If ignition switch control of the radio is desired, the radio power leads may be connected to the battery through a relay which is controlled by the ignition switch. 2.4-10 Alternator/Generator Whine 2.4.3 Alternator/Generator Whine This type of interference is characterized by a high-pitched whine which varies with engine speed. A 0.5 F coaxial capacitor (Motorola Part No. 8C82571B01) can be used to bypass the whine. For generators, the capacitors is connected in the armature lead. Never use a capacitor in the eld lead. Use the eld suppressor assembly supplied in the TLN6252 Noise Reduction Kit. For alternators, the capacitor is connected in the lead to the battery post (see Figure 2.4-2 and 2.4-3). Step 1. Mount Capacitor
(0.5F Coaxial Type) under generator ground screw. Step 3. Connect wire lead to capacitor using lockwasher and nut. Step 4. Connect capacitor lead to armature post. Caution:
Do not connect capacitor to field teminal. Step 2. Disconnect wire (dashed) from armature post and connect to capacitor using lockwasher and nut. Figure 2.4-2. Generator Whine Suppression FL0830310-O Step 1. Mount Capacitor to
(0.5F Coaxial Type) under alternator ground screw. Step 2. Disconnect wire from battery post and connect to capacitor using lockwasher and nut. Caution:
Do not connect capacitor to field terminal. Step 3. Connect wire lead to capacitor using lockwasher and nut. Step 4. Connect capacitor lead to battery post. FL0830311-O Figure 2.4-3. Alternator Whine Suppression Voltage Regulator Noise 2.4-11 2.4.4 Voltage Regulator Noise This type of interference is characterized by erratic popping noises which change only slightly with changes in engine speed. The noise is generated by arcing in the vibrating breaker contacts of the voltage regulator. It can be suppressed by connecting a 0.5 F coaxial capacitor (Motorola Part No. 8C82571B01) in the battery and armature leads of the voltage regulator (see Figure 2.4-4).
CAUTION: Disconnect the battery ground terminal before attempting to connect components to the voltage regulator. Step 1. Mount Capacitor
(0.5F Coaxial Type) to vehicle chassis using lockwasher and self-tapping screw. Vehicle Step 2. Disconnect wire (dashed) from battery post and connect to capacitor using lockwasher and nut. Battery Post Step 3. Add lead from battery post to capacitor using lockwasher and nut. Armature A coaxial capacitor can be added here, if required. FL0830265-O Figure 2.4-4. Voltage Regulator Noise Suppression 2.4.5 Hood and Trunk Lid Noise This type of noise is characterized by irregular popping sounds. It is caused by friction in poorly bonded automobile hoods or trunk lids. This friction causes static electricity to build up until arcing occurs. This type of noise is suppressed using a Motorola Hood Wipers and Mounting Hardware Kit
(part of TLN8845 or TLN6252 Noise Reduction Kits) which provides electrical bonding of the hood or trunk to the vehicle body while permitting them to be opened. 2.4-12 Other Electrical Noises 2.4.6 Other Electrical Noises Other elements of the electrical system which can generate noise are listed below. These can be suppressed by connecting a 0.5 F bypass capacitor between the noise source and ground. 1. Ammeter-to-battery lead 2. Gauges (oil, fuel, temperature) 3. Ignition Switch 4. Lamp bulbs (headlamps, tail lamps, dome lamps, etc.) 5. Accessory wiring (electrical fuel pump, electric windshield wipers, heater fan motor, window openers, etc.) 2.4.7 Wheel Static Road friction can cause static build-up on the front wheels. Suppress noise from this source using wheel static collector rings (Motorola Part No. 1K534254 regular type - 1K653173 small type). 2.4.8 Ground Bonding If a vehicle is not properly bonded to ground, static charges can increase. This increase can cause noise from electrical arcing. This type of noise is suppressed by bonding the part using one-inch wide ground straps (keep them as short as possible). Some common points where bonding may be helpful are listed below (see Figure 2.4-5). A. From engine block to the rewall. B. From engine block to vehicle frame at points where the engine is shock-mounted. C. From the battery ground terminal to the vehicle body. D. From top of front wheel A frames to chassis, particularly in cases where rubber-mounted members are used. Firewall Battery C A Fender Well Chassis Front Wheel
"A" Frame D B D Figure 2.4-5. Ground Bonding FL0830266-O Ground Bonding 2.4-13
1 2 | Users Manual | Users Manual | 755.37 KiB |
CONTENTS Computer Software Copyrights . 3 Radio Overview . 5 Parts of the Radio . 5 Optional Enhanced DTMF (Keypad) Microphone (RMN4026) . 6 On/Off/Volume Knob . 7 Channel Selector/Menu Navigation Buttons . 7 LED Indicators . 7 Programmable Buttons . 7 Push-to-Talk (PTT) Button . 10 Microphone . 10 Menu Keys . 10 Use with Optional Enhanced DTMF Microphone (RMN4026) . 11 LCD Screen . 13 Audio Indicators for Programmable Buttons . 14 Getting Started . 15 Turning the Radio On or Off . 15 Adjusting the Volume . 15 Selecting a Zone . 16 Selecting a Radio Channel . 16 Sending a Call . 17 Receiving a Call . 17 Radio Calls . 19 Making a Selective Call . 19 Receiving a Selective Call . 19 Sending a Call Alert Page. 20 Receiving a Call Alert Page . 20 Radio Check . 21 Sending a Status . 21 Sending a Message . 22 Receiving a Message . 23 Sending an Emergency Alert . 23 Receiving Selective Radio Inhibit . 24 Editing a Radio Call List . 24 Repeater or Talkaround Mode . 25 Setting the Power Level . 25 Name and Call/Message Tone Tagging . 26 Scan . 29 Starting or Stopping Scan. 29 Talkback . 30 Deleting a Nuisance Channel . 30 Restoring a Channel to the Scan List . 30 C O N T E N T S 1 English S T N E T N O C Editing a Scan List . 30 Adding or Deleting Channels in a Scan List . 31 Prioritizing a Channel in a Scan List . 32 Setting Priority Channels . 32 Phone. 35 Making a Phone Call . 35 Modifying the Phone List . 36 Adding an Entry (when using the keypad microphone only) . 36 Deleting an Entry: . 37 Editing an Entry (when using the keypad microphone only) . 38 Editing an Access/Deaccess Code
(when using the keypad microphone only) . 39 Audio/Tone Settings. 41 Utilities. 43 Setting the Time . 45 Displaying the Time . 46 Selecting the Display Language . 46 Safety and Warranty . 47 Safe and Efficient Operation of Motorola Two-Way Radios . 47 Exposure to Radio Frequency Energy. 47 Electromagnetic Interference/
Compatibility . 48 Operational Warnings . 48 Vehicles with an Air Bag . 48 Potentially Explosive Atmospheres. 48 Blasting Caps and Blasting Areas. 49 Mobile Radio Operation and EME Exposure . 49 Mobile Antenna Installation. 50 Control Station Operation. 50 Limited Warranty . 50 Accessories . 55 Audio . 55 Mounting . 55 Antennas . 56 Control Station . 56 English 2 COMPUTER SOFTWARE COPYRIGHTS The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modied, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. C O N T E N T S 3 English S T N E T N O C Notes English 4 RADIO OVERVIEW PARTS OF THE RADIO On/Off/Volume Knob Red/Yellow/Green LED Indicators LCD Screen Channel Selector/
Menu Navigation Buttons
(Up/Down) Menu Exit/Escape Button Menu Enter/Select Button Programmable Button 3 (P3)
(Interchangeable) I R A D O O V E R V E W I Microphone Jack Programmable Button 1 (P1)
(Interchangeable) Programmable Button 2 (P2)
(Interchangeable) Editing Buttons
(Left/Right) Programmable Button 4 (P4)
(Interchangeable) 5 English I W E V R E V O O D A R I Optional Enhanced DTMF (Keypad) Microphone (RMN4026) Your radio may be ordered with an optional DTMF (Dual-Tone Multi-Frequency) microphone that has a direct entry keypad. This keypad microphone has three buttons
(A, B, C) below the keypad that can be programmed to conveniently activate select radio features. Push-to-Talk
(PTT) button Keypad Programmable Buttons
(A, B, C) English 6 On/Off/Volume Knob Turns the radio on or off, and adjusts the radios volume. Channel Selector/Menu Navigation Buttons y or z Used for channel scrolling. When in menu mode, used for menu navigation. LED Indicators Indicates channel, scan, and monitor status, as well as receipt of a selective call. Programmable Buttons Your radio has several programmable buttons. Your dealer can program these buttons as shortcuts to various radio features. Check with your dealer for a complete list of functions your radio supports. Programmable buttons include the i buttons (see page 5).
, and j g
, h Some buttons can access up to two features, depending on the type of button press:
short press quickly pressing and releasing the programmable buttons pressing and holding the long press programmable buttons for a period of time
(at least 1 1/2 seconds) hold down pressing and holding down the programmable buttons while checking status or making adjustments A summary of programmable radio features and corresponding page references appears beginning on page 8. In the Button column, have your dealer record the name of the programmable button next to the feature that has been programmed to it. The dealer can use the abbreviations (P1, P2, P3, P4) shown in the radio illustration on page 5. Also, where appropriate, have your dealer indicate whether the button press requires a short press, a long press, or needs to be held down. I R A D O O V E R V E W I 7 English Function Indicator Short Press Long Press Volume Set Home Revert Direct Channel Access Direct Zone Access PRTT (Priority Request- to-Talk) Emergency Power Level Repeater/
Talkaround Scan/Nuisance Channel Delete E B J G Takes you directly to a pre-programmed zone/channel combination. Toggle the direct access channel feature.
(DTMF microphone required.) Direct entry to zone selection menu. Sends a priority access request to the dispatcher. Initiate Emergency Alert. Cancel Emergency status. Toggle transmit power level between High and Low. Toggle between using a repeater or transmitting directly to another radio. Delete a nuisance channel while scanning. Toggle scan on and off. I W E V R E V O O D A R I Phone This function is activated by D Access Phone Mode. EITHER a short OR a long press, but not both. Hold Down Page Button Sound a tone for adjusting your radios volume level. 15 16 16 16 17 23 25 25 29-30 35 English 8 Function Indicator Short Press Long Press Hold Down Page Button Speed Dial Access your phone list directly. Monitor Option Board
(if one is installed) Radio Call Light Auxiliary Control (1/2) Status One-Touch Status Message One-Touch Message Horn and Lights Toggle silent monitor operation (also turn off open squelch monitor when it has been activated). Turn on open squelch monitor. Toggle between activating and deactivating the option board. Access the radio call menu. Adjust brightness level (off/low/med/high). Activates or deactivates a pin on the accessory connector.
(See your dealer.) Direct entry to the status menu. Immediately sends a preprogrammed status. Direct entry to the message menu. Immediately sends a preprogrammed message. Toggles external alarm feature or cancels a triggered alarm. C N 35 I R A D O O V E R V E W I This function is activated by EITHER a short OR a long press, but not both. 9 English Up Key y and Down Key z Used for channel scrolling. When in Menu Mode, used for menu navigation. w Right Key Moves the cursor right or inserts a space when editing. Left Key v Moves the cursor left or used as a backspace key when editing. I W E V R E V O O D A R I Push-to-Talk (PTT) Button Press and hold down this button to talk;
release it to listen. Microphone Hold the microphone 1 to 2 inches (2.5 to 5 cm) from your mouth, and speak clearly into it. Menu Keys Up Exit Menu/
Select t y u v z w Left Right Down Menu/Select Key u Used to enter Menu Mode. When in Menu Mode, this key is also used to make menu selections. Exit Key t Used to move to the previous Menu level (short press) or to exit Menu Mode (long press). English 10 Use with Optional Enhanced DTMF Microphone (RMN4026
) 1 2 3 4 5 6 7 8 9
* 0 #
* * *A C B These keys are used to:
Dial a phone number Make a radio call Enter information when programming radio lists Directly access preprogrammed features Each key can generate several different characters. For example, to enter the character C, press the following table.) key three times. (Refer to the 2 I R A D O O V E R V E W I 11 English Entering Characters Using the Keypad Number of Times Key is Pressed Key 0 1 2 3 4 5 6 7 8 1 0 1 A D G J M P T 9 W
2
B E H K N Q U X
Blank Space 3
) 4
C F I L O R V Y
2 3 4 5 6 S 8 Z
. 5
a d g j m 7 t 9
6 7 8 9 10 11 12 13 14 15 16 17 b e h k n p u w
c f i l o q v x 2 3 4 5 6 r 8 y s z 7 9 Y y
I W E V R E V O O D A R I English 12 LCD Screen Symbol Indication The top screen row displays radio status information:
Symbol A Companding B Power Level Indication The Companding feature is activated. When in narrow band, this feature improves audio quality. Low Power R or High Power S is activated. C Carrier Squelch
(CSQ) The radio is on a CSQ channel, monitor is active, or the microphone is off-hook. D Phone E Emergency F Call Received G Scan Priority 1 Scan
ashing) H Priority 2 Scan
steady) Phone Mode is selected. An Emergency Alert is being sent. A Selective Call or Call Alert has been received. The Scan feature is active. During Scan, indicates that the scan has locked on to a priority 1 channel. During Scan, indicates that the scan has locked on to a priority 2 channel. I R A D O O V E R V E W I 13 English Symbol Indication AUDIO INDICATORS FOR PROGRAMMABLE BUTTONS J Talkaround K Programming Mode M Signal Strength N Option Board The radio is not transmitting through a repeater. The radio is in Program List editing mode. Indicates signal strength. The more bars, the stronger the signal. Option board is enabled. Q L Not currently assigned. Not currently assigned. Low-High Tone High-Low Tone In addition to having associated visual indicators, some programmable buttons use tones to indicate one of two modes:
Button Low-High Tone High-Low Tone Scan Power Level Start scan High power selected Stop scan Low power selected Option Board Enabled Disabled Repeater/
Talkaround Does not use repeater Uses repeater I W E V R E V O O D A R I English 14 ADJUSTING THE VOLUME Turn the On/Off/Volume Control knob clockwise to increase the volume, or counterclockwise to decrease the volume. or 1 Hold down the Volume Set button (see page 8). You will hear a continuous tone. 2 Turn the On/Off/Volume Control knob to the desired volume level. 3 Release the Volume Set button. GETTING STARTED TURNING THE RADIO ON OR OFF OFF Push the On/Off/
Volume Control knob until you hear a click and the display clears. ON Push the On/Off/
Volume Control knob until you hear a click. If power-up is successful, you will hear the Self-Test Pass Tone. If the radio fails to power up, you will hear the Self-Test Fail Tone
. I G E T T N G S T A R T E D 15 English SELECTING A ZONE A zone is a group of up to 16 channels. Before you can access a channel in a zone, you must select the zone in one of two ways:
Method 1 1 u to enter Menu Mode. 2 y or z until 3 u to select ZZZZoooonnnneeee ZZZZoooonnnneeee 4 y or z until you see the desired zone name. 5 u to select the zone. SELECTING A RADIO CHANNEL Your radio offers 128 channels (8 zones of 16 channels each). Note: Due to government regulations, some channels may not be programmed. See your dealer for more information. There are three ways to select a channel:
Method 1 1 Select the appropriate Zone, if required. 2 y or z until you reach the desired channel, shown on LCD display. Method 2 (if programmed by your dealer [see pages 8 -9]). Method 2 (if programmed by your dealer [see pages 8 -9]). 1 Press the Home Revert button. 1 Press the Direct Zone Access button. 2 y or z until you reach the desired zone. 3 u to select the zone. Method 3 (if programmed by your dealer [see pages 8 -9]). 1 Press the Direct Channel Access button. D E T R A T S G N T T E G I English 16 2 Enter the desired channel using the DTMF 4 Hold the microphone vertically 1 to 2 inches keypad microphone. 3 u to conrm your selection. SENDING A CALL 1 Turn your radio on.
(2.5 to 5 cm) from your mouth. Press the PTT to talk; release it to listen. 5 Release the PTT to listen. RECEIVING A CALL 2 y or z to select the desired channel. 3 Hold the microphone vertically 1 to 2 inches
(2.5 to 5 cm) from your mouth. Press the PTT to talk; release it to listen. 1 2 3 Turn your radio on. Adjust the radios volume, if necessary (see page 15). Select the desired channel. If your system uses the request-to-talk feature, use the following method to send a call:
4 Hold the microphone vertically 1 to 2 inches
(2.5 to 5 cm) from your mouth. Press the PTT to talk; release it to listen. 1 Turn your radio on. 2 y or z to select the desired channel. 3 Press the PTT (for priority requests to talk, the PRTT button) and wait for the talk permit tone. I G E T T N G S T A R T E D 17 English GETTING STARTED E n g l i s h 1 8 N o t e s I R A D O C A L L S 8 Press the PTT to talk; release it to listen. 9 When nished with the call, t to return to or Hold down t to exit Menu Mode. SSSSeeeelllleeeeccccttttiiiivvvveeee CCCCaaaallllllll RECEIVING A SELECTIVE CALL F When you receive a selective call:
You will hear two alert tones. The LED Indicator ashes yellow. The LCD screen displays F and the preprogrammed name or ID of the calling radio, if available. RADIO CALLS MAKING A SELECTIVE CALL You can make a selective call to a particular radio or group of radios, provided the signalling protocol supports it. To make a Selective Call:
1 u to enter Menu Mode. 2 y or z until RRRRaaaaddddiiiioooo CCCCaaaallllllll 3 u to select RRRRaaaaddddiiiioooo CCCCaaaallllllll 4 y or z until SSSSeeeelllleeeeccccttttiiiivvvveeee CCCCaaaallllllll 5 u to select SSSSeeeelllleeeeccccttttiiiivvvveeee CCCCaaaallllllll 6 y or z to locate the desired ID in the Radio Call List. or when using the keypad microphone only, enter the ID number of the radio you want to call. 7 Press the PTT to send the call. The radio sounds a continuous tone. 19 English S L L A C O D A R I SENDING A CALL ALERT PAGE You can alert another person by sending a Call Alert page. To send a Call Alert page:
1 u to enter Menu Mode. 2 y or z until RRRRaaaaddddiiiioooo CCCCaaaallllllll 3 u to select RRRRaaaaddddiiiioooo CCCCaaaallllllll 4 y or z until CCCCaaaallllllll AAAAlllleeeerrrrtttt 5 ) to select CCCCaaaallllllll AAAAlllleeeerrrrtttt 6 y or z to locate the desired ID in the Radio Call List;
or when using the keypad microphone only, enter the ID number of the radio you want to page. 7 Press the PTT to send the page. You will see CCCCaaaallllllll IIIInnnn PPPPrrrroooogggg 8 If the Call Alert page is received, you will see If not, you will see AAAAcccckkkknnnnoooowwwwlllleeeeddddggggeeee NNNNoooo AAAAcccckkkknnnnoooowwwwlllleeeeddddggggeeee 9 t to return to CCCCaaaallllllll AAAAlllleeeerrrrtttt or Hold down t to exit Menu Mode. RECEIVING A CALL ALERT PAGE When your radio receives a Call Alert page, it sounds four alert tones continuously and the following are displayed until you respond:
the F symbol, and the ID of the calling radio alternating with Call Received. Press the PTT to answer the page, or press any other key to clear it. Note: Your radio will display only the last Call Alert page received. Also, your radio will not receive any Selective Calls until you clear the page. English 20 RADIO CHECK This feature allows you to determine if a radio is in range without disturbing the user of the radio. Radio Check can also be used when attempts with Selective Call and Call Alert fail.
(This feature is available only if your signalling protocol supports it.) To perform a Radio Check:
1 u to enter Menu Mode. 2 y or z until RRRRaaaaddddiiiioooo CCCCaaaallllllll 3 u to select RRRRaaaaddddiiiioooo CCCCaaaallllllll 4 y or z until RRRRaaaaddddiiiioooo CCCChhhheeeecccckkkk 5 u to select RRRRaaaaddddiiiioooo CCCChhhheeeecccckkkk 6 y or z to locate the desired ID in the Radio Call List;
or when using the keypad microphone only, enter the ID number of the radio you are checking. 7 8 Press the PTT. You will see CCCCaaaallllllll IIIInnnn PPPPrrrroooogggg If the Radio Check is received, you will see AAAAcccckkkknnnnoooowwwwlllleeeeddddggggeeee If not, you will see NNNNoooo AAAAcccckkkknnnnoooowwwwlllleeeeddddggggeeee I R A D O C A L L S 9 t to return to RRRRaaaaddddiiiioooo CCCChhhheeeecccckkkk RRRRaaaaddddiiiioooo CCCChhhheeeecccckkkk or Hold down t to exit Menu Mode. SENDING A STATUS This feature gives you the ability to send a status update to the base. The status feature makes more efcient use of the channel compared to voice transmissions. Status updates of up to 14 characters may be programmed by your dealer. To send a Status:
1 u to enter Menu Mode. 2 y or z until SSSSttttaaaattttuuuussss 3 u to select SSSSttttaaaattttuuuussss 21 English S L L A C O D A R I 4 y or z to locate the desired status in the pre-programmed list. or when using the keypad microphone only, enter the number of the status you wish to send. or if programmed by your dealer (see pages 8 -9), press the button that has been preprogrammed for a specic status. Note: You cannot retransmit the current status update. SENDING A MESSAGE This feature gives you the ability to send and receive preprogrammed messages. Data messages make more efcient use of channels compared to voice transmissions. Messages of up to 14 characters may be programmed by your dealer. To send an electronic (data) message:
1 u to enter Menu Mode. 2 y or z until MMMMeeeessssssssaaaaggggeeee 3 u to select MMMMeeeessssssssaaaaggggeeee 4 y or z to locate the desired message in the preprogrammed list. or when using the keypad microphone only, enter the number of the message you wish to send. or if programmed by your dealer (see pages 8 -9), press the button that has been preprogrammed for a specic message. English 22 I R A D O C A L L S The E symbol will appear on the display when your radio is in the Emergency Alert state. An Emergency Alert can be programmed to:
Show E and sound a tone or Show E (Silent Emergency) or Activate the microphone so that all activity can be transmitted (for a predetermined amount of time). See your dealer for more information. To cancel the Emergency Alert, press and hold down the Emergency button. RECEIVING A MESSAGE When your radio receives a message:
You will hear two alert tones. The LED indicator ashes yellow. The LCD screen displays alternating with the preprogrammed alias. MMMMssssgggg RRRReeeecccceeeeiiiivvvveeeedddd Note: If you receive a message that is programmed into your radio, the display will alternate with the following:
MMMMeeeessssssssaaaaggggeeee ####____ and NNNNoooo AAAAlllliiiiaaaassss SENDING AN EMERGENCY ALERT E A priority Emergency Alert can be sent to a specic radio or dispatch center by pressing:
A button preprogrammed by your dealer
(see pages 8 -9). The footswitch A pushbutton accessory Emergency Alerts have priority over all other calls. 23 English S L L A C O D A R I RECEIVING SELECTIVE RADIO INHIBIT Your radio is equipped with a security feature that can temporarily render the unit inoperative. This feature is commonly used to disable radios:
When your vehicle is being serviced For system control reasons Note: When your radio has been disabled, all In case of theft controls will be inoperative. When the radio is powered up, the display will show:
RRRRaaaaddddiiiioooo DDDDiiiissssaaaabbbblllleeeedddd EDITING A RADIO CALL LIST K The ID numbers in your Radio Call List are preprogrammed by your dealer. However, you can edit the names associated with these IDs using the optional keypad microphone. The K symbol will appear on the display when you are editing. Note: Your radio cannot receive any calls while you are editing. To edit a Call List entry:
1 u to enter Menu Mode. 2 y or z until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 3 u to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 y or z until RRRRaaaaddddiiiiooooCCCCaaaallllllll LLLLiiiisssstttt 5 u to select RRRRaaaaddddiiiiooooCCCCaaaallllllll LLLLiiiisssstttt 6 y or z until EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
7 u to select EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
8 y or z until you locate the desired entry. 9 u to select the entry. 10 Use your keypad to edit the entry (see page 11). 11 u to save your changes. You will see 12 t to return to EEEEnnnnttttrrrryyyy SSSSaaaavvvveeeedddd EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
or Hold down t to exit Menu Mode. English 24 I R A D O C A L L S REPEATER OR TALKAROUND J MODE Talkaround Mode enables you to communicate with another radio when either:
The repeater is not operating. or Your radio is out of the repeaters range but within communicating distance of another radio. The J symbol appears on the display when Talkaround Mode is selected. To select either Repeater Mode or Talkaround Mode:
Press the preprogrammed Repeater/
Talkaround button (see page 8) to toggle between Repeater Mode and Talkaround Mode. or 1 u to enter Menu Mode. 2 y or z until RRRRppppttttrrrr////TTTTaaaallllkkkkaaaarrrrnnnndddd 3 u to select RRRRppppttttrrrr////TTTTaaaallllkkkkaaaarrrrnnnndddd 4 y or z until RRRReeeeppppeeeeaaaatttteeeerrrr MMMMooooddddeeee or until TTTTaaaallllkkkkaaaarrrrnnnndddd MMMMooooddddeeee 5 u to conrm your selection. SETTING THE POWER LEVEL B Each channel in your radio has a predened transmit power level that can be changed. High power ( S ) Low power ( R ) You can set the power level in two ways:
Method 1 Press the preprogrammed Power Level button
(see page 8) to toggle between low and high. or Method 2 1 u to enter Menu Mode. 2 y or z until UUUUttttiiiilllliiiittttiiiieeeessss 3 u to select UUUUttttiiiilllliiiittttiiiieeeessss 25 English S L L A C O D A R I 4 y or z until PPPPoooowwwweeeerrrr LLLLeeeevvvveeeellll 5 u to select PPPPoooowwwweeeerrrr LLLLeeeevvvveeeellll The display shows the current power level. To tag a specic users name or message:
1 u to enter Menu Mode. 2 y or z until AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss 6 y or z until PPPPoooowwwweeeerrrr HHHHiiiigggghhhh????
3 u to select AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss or until PPPPoooowwwweeeerrrr LLLLoooowwww????
4 y or z until NNNNaaaammmmeeee TTTToooonnnneeee TTTTaaaagggg 7 u to conrm the selection. or MMMMssssgggg TTTToooonnnneeee TTTTaaaagggg NAME AND CALL/MESSAGE TONE TAGGING You can program your radio to sound a particular alert tone when:
a specic user is callingname tone tagging, or a message is being sent to your radio, or your radio is receiving a type of radio call call tone tagging. There are seven alert tones to select from. 5 u to select NNNNaaaammmmeeee TTTToooonnnneeee TTTTaaaagggg or MMMMssssgggg TTTToooonnnneeee TTTTaaaagggg 6 y or z until you see the name or message you want to tag. 7 u to conrm the selection. 8 y or z until you hear one of the seven tones you want to use for this name or message. 9 u to conrm the selection. You will see or NNNNaaaammmmeeee TTTTaaaagggg SSSSeeeetttt MMMMssssgggg TTTToooonnnneeee TTTTaaaagggg English 26 I R A D O C A L L S 10 t to return to NNNNaaaammmmeeee TTTToooonnnneeee TTTTaaaagggg 9 u to conrm the selection. You will see CCCCaaaallllllll TTTToooonnnneeee TTTTaaaagggg 10 t to return to CCCCaaaallllllll TTTToooonnnneeee TTTTaaaagggg or Hold down t to exit Menu Mode. MMMMssssgggg TTTToooonnnneeee TTTTaaaagggg or or Hold down t to exit Menu Mode. To tag a type of radio call:
1 u to enter Menu Mode. 2 y or z until AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss 3 u to select AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss 4 y or z until CCCCaaaallllllll TTTToooonnnneeee TTTTaaaagggg 5 u to select CCCCaaaallllllll TTTToooonnnneeee TTTTaaaagggg 6 y or z until you see the call type you want to tag. 7 u to conrm the selection. 8 y or z until you hear the tone you want to use for this type of call. 27 English Notes S L L A C O D A R I English 28 You can start or stop a scan operation either by:
pressing the preprogrammed Scan button (see page 8) to start or stop scanning;
or 1 ) to enter Menu Mode. 2 + or e until SSSSyyyysssstttteeeemmmm SSSSccccaaaannnn 3 ) to select SSSSyyyysssstttteeeemmmm SSSSccccaaaannnn 4 + or e until SSSSyyyyssss SSSSccccaaaannnn OOOOnnnn????
or SSSSyyyyssss SSSSccccaaaannnn OOOOffffffff????
5 ) to conrm your selection. S C A N SCAN Your radio can monitor multiple channels in a scan list. Your dealer can program up to 16 different channels into each scan list. When your radio detects activity on a scan list channel, it will automatically switch to that channel. Note: The same channels can be assigned to different scan lists. STARTING OR STOPPING SCAN G The Gsymbol, and the number of the channel you are transmitting on, will appear on the display when you start a scan operation. The green LED indicator blinks during a scan operation and stops blinking when the radio switches to a channel. Note: If you enter Menu Mode while the radio is scanning, scanning will stop. It will resume when you exit Menu Mode. 29 English N A C S TALKBACK The Talkback feature allows you to respond to a transmission while scanning. If a transmission on a channel is detected while scanning, the radio will stop on that channel for a preprogrammed period of time. During this hangtime you may respond by pressing the PTT. Note: If transmission stops/ceases or if the PTT is not pressed for a preprogrammed duration, the radio will continue scanning. Also, the LED scan indicator stops blinking while the radio is in hangtime. DELETING A NUISANCE CHANNEL If a channel continually generates unwanted calls or noise (a nuisance channel), use the Scan button to temporarily delete the channel from the scan list. Note: You cannot delete a priority channel (see page 32) or the last remaining channel in a scan list. 1 While the radio is on the nuisance channel, hold down the Scan button until you hear a tone. 2 Release the Scan button. The nuisance channel is deleted. Restoring a Channel to the Scan List To restore a previously deleted channel to the scan list, restart the scan operation or turn your radio off and on again. EDITING A SCAN LIST A scan list is a group of up to 16 channels. Each channel can have a scan list assigned to it. The same channel can be included in several scan lists, and the same scan list can be assigned to several Channel Selector positions. For example:
Position 2 Position 14 C h a n n e l s 1 3 5 6 1 2 3 11 When you edit a scan list, you can either add, delete, or prioritize channels. The K symbol will appear on the display while you are in edit mode. Note: Your radio cannot receive any calls while you are editing a scan list. English 30 Adding or Deleting Channels in a Scan List To add or delete channels in a scan list:
1 ) to enter Menu Mode. 2 + or e until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 + or e until SSSSccccaaaannnn LLLLiiiisssstttt 5 ) to select SSSSccccaaaannnn LLLLiiiisssstttt 6 + or e until AAAAdddddddd EEEEnnnnttttrrrryyyy????
or until DDDDeeeelllleeeetttteeee EEEEnnnnttttrrrryyyy????
7 ) to conrm your selection. 8 + or e until you see the channel you want to add or delete. Note: You cannot delete the last remaining channel in a scan list. 9 ) to conrm your selection. 10 If you added a channel, EEEEnnnnttttrrrryyyy SSSSaaaavvvveeeedddd you will see or If you deleted a channel, you will see
) to conrm the deletion. You will see DDDDeeeelllleeeetttteeee????
EEEEnnnnttttrrrryyyy DDDDeeeelllleeeetttteeeedddd 11 ( to return to AAAAdddddddd EEEEnnnnttttrrrryyyy????
or to return to or Hold down ( to exit Menu Mode. DDDDeeeelllleeeetttteeee EEEEnnnnttttrrrryyyy????
S C A N 31 English Prioritizing a Channel in a Scan List Setting Priority Channels You may want to check the activity on one or two channels more frequently than others. You can do this by assigning them priority:
Note: Even if there may be activity on a non-
priority channel, your radio will automatically switch to an active priority channel and indicate the activity with a short tone. N A C S Priority Channel Scanning Sequence None specied Ch1 Ch2 Ch3 Ch4 Ch1 Channel 2
(Priority 1) Channel 2
(Priority 1) Channel 8
(Priority 2) Ch2 Ch1 Ch2 Ch3 Ch2 Ch4 Ch2 Ch1 Ch2 Ch1 Ch8 Ch3 Ch2 Ch4 Ch8 Ch1 Note: You cannot reprioritize a Priority 1 channel to Priority 2. 1 ) to enter Menu Mode. 2 + or e until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 + or e until SSSSccccaaaannnn LLLLiiiisssstttt 5 ) to select SSSSccccaaaannnn LLLLiiiisssstttt 6 + or e until EEEEddddiiiitttt PPPPrrrriiiioooorrrriiiittttyyyy????
7 ) to select EEEEddddiiiitttt PPPPrrrriiiioooorrrriiiittttyyyy????
8 + or e until PPPPrrrriiiioooorrrriiiittttyyyy ####1111????
or until PPPPrrrriiiioooorrrriiiittttyyyy ####2222????
9 ) to select the desired priority level. 10 + or e until you see the channel you want to prioritize. English 32 11 ) to prioritize that channel. 12 ( to return to EEEEddddiiiitttt PPPPrrrriiiioooorrrriiiittttyyyy????
or Hold down ( to exit Menu Mode. Note: If you want to reprioritize all channels, you must rst delete each priority channel from the scan list, and then add it back. S C A N 33 English NOTES S E T O N English 34 PHONE If your radio has access to a telephone system, you can make a phone call. To do this, your radio must send an access code to a station that connects it to a phone line. (Ask your dealer for more details.) After completing a call, your radio must send a deaccess code to hang up. MAKING A PHONE CALL D You can make a phone call using the preprogrammed Phone button (see page 8) or the radio menu. The D symbol appears on the LCD screen when you are in Phone Mode. To initiate a phone call:
Press the Phone button. or Do the following:
1 Switch to the desired channel. 2 ) to enter Menu Mode. 3 + or e until PPPPhhhhoooonnnneeee 4 ) to select PPPPhhhhoooonnnneeee 5 You will hear a series of tones indicating that an access code is being sent automatically. You will also see your access code displayed;
or when using the keypad microphone only, enter your access code using the keypad. 6 When you hear a dial tone, enter or select a phone number:
when using the keypad microphone only, enter the phone number using the keypad. or
+ or e to select a number from the phone list. or when using a keypad microphone only, a Press and release the preprogrammed Speed Dial button (see page 9) to use the Speed Dial feature. b Press the key (1 to 8) corresponding to the number you want to call, or-
press 0 if you want to call the last number dialed. P H O N E 35 English Note: To redial the last number dialed (if not using Speed Dial), do not choose a number. Proceed to step 7. Alternatively, if you entered your access code using the keypad, press the e key once to access the last number dialed; then press and release the PTT. 7 8 To end a phone call, do one of the following:
If your radio has the deaccess code preprogrammed, proceed to step 8. or Enter the deaccess code using the keypad. Press the Phone button to exit Phone Mode. or
( to exit Phone Mode and return to PPPPhhhhoooonnnneeee or Hold down ( to exit Menu Mode. MODIFYING THE PHONE LIST K You can modify a phone list in one of the following ways:
Add an entry Delete an entry Edit an existing entry Edit an Access/Deaccess code When you are modifying the phone list, the K symbol will appear on the display. Note: Your radio cannot receive any calls while you are modifying the phone list. Adding an Entry (when using the keypad microphone only) To add an entry:
1 ) to enter Menu Mode. 2 + or e until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 + or e until PPPPhhhhoooonnnneeee LLLLiiiisssstttt 5 ) to select PPPPhhhhoooonnnneeee LLLLiiiisssstttt E N O H P English 36 6 + or e until AAAAdddddddd EEEEnnnnttttrrrryyyy????
14 ( to return to AAAAdddddddd EEEEnnnnttttrrrryyyy????
7 ) to select AAAAdddddddd EEEEnnnnttttrrrryyyy????
You will see EEEEnnnntttteeeerrrr NNNNaaaammmmeeee 8 Use the keypad to enter the name (see page 11). or Hold down ( to exit Menu Mode. Deleting an Entry:
To delete an entry:
9 ) to store the name. 1 ) to enter Menu Mode. You will see EEEEnnnntttteeeerrrr PPPPhhhhoooonnnneeee ####
2 + or e until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 10 Use the keypad to enter the phone number. You can also add a dash (press f) and a Pause Indicator (hold down # until the # character on the display changes to a P). 11 ) to select the phone number. 12 + or e until you see the location in the list where you want to store the phone number. 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 + or e until PPPPhhhhoooonnnneeee LLLLiiiisssstttt 5 ) to select PPPPhhhhoooonnnneeee LLLLiiiisssstttt 6 + or e until DDDDeeeelllleeeetttteeee EEEEnnnnttttrrrryyyy????
7 ) to select DDDDeeeelllleeeetttteeee EEEEnnnnttttrrrryyyy????
13 ) to store the phone number. 8 + or e until you see the entry you You will see EEEEnnnnttttrrrryyyy SSSSaaaavvvveeeedddd want to delete. P H O N E 37 English 9 ) to select the entry. DDDDeeeelllleeeetttteeee????
You will see
) again to conrm the deletion. You will see EEEEnnnnttttrrrryyyy DDDDeeeelllleeeetttteeeedddd 10 ( to return to DDDDeeeelllleeeetttteeee EEEEnnnnttttrrrryyyy????
or Hold down ( to exit Menu Mode. Editing an Entry (when using the keypad microphone only) To edit an entry:
1 ) to enter Menu Mode. 2 + or e until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 + or e until PPPPhhhhoooonnnneeee LLLLiiiisssstttt 5 ) to select PPPPhhhhoooonnnneeee LLLLiiiisssstttt 6 + or e until EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
7 ) to select EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
E N O H P English 38 8 + or e until you see the entry you want to edit. 9 ) to select the entry. 10 + or e until EEEEddddiiiitttt NNNNaaaammmmeeee????
to edit the name, or until to edit the phone number, or until to edit the location in the phone list. EEEEddddiiiitttt NNNNuuuummmmbbbbeeeerrrr????
EEEEddddiiiitttt LLLLooooccccaaaattttiiiioooonnnn????
11 ) to conrm your selection. 12 Use the keypad to edit the entry (see page 11). or
+ or e until you see the location where you want to store the phone number. 13 ) to store the information. 14 ( to return to EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
or Hold down ( to exit Menu Mode. Editing an Access/Deaccess Code (when using the keypad microphone only) To edit an access/deaccess code:
1 ) to enter Menu Mode. 10 + or e to edit another code. or Hold down ( to exit Menu Mode. 2 + or e until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 + or e until EEEEddddiiiitttt CCCCooooddddeeeessss????
5 ) to select EEEEddddiiiitttt CCCCooooddddeeeessss????
6 + or e until AAAAcccccccceeeessssssss CCCCooooddddeeee????
or until DDDDeeeeaaaacccccccceeeessssssss CCCCooooddddeeee????
7 ) to select AAAAcccccccceeeessssssss CCCCooooddddeeee????
or DDDDeeeeaaaacccccccceeeessssssss CCCCooooddddeeee????
8 Enter the number using the keypad microphone. 9 ) to select the entry. P H O N E 39 English Notes E N O H P English 40 S E T T N G S I I A U D O T O N E
AUDIO/TONE SETTINGS You can customize the audio and tone feature settings on your radio. 1 ) to enter Menu Mode. 2 + or e until AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss 3 ) to select AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss 4 + or e until you see the feature you want to change. (Refer to the table below.) 5 ) to select the feature. You will see the features current setting. 6 + or e for available settings. (Refer to the table below.) 7 ) to select the desired setting. Feature Alert Vol Lvl Audio/Tone Settings What it Does Makes the volume level of the audio and alert tones independent. These two volume levels can be adjusted independently. Tone Disable Turns all tones on or off. Settings Ind Alert Off Ind Alert On Tones On Tones Off 41 English
E N O T O D U A I I S G N T T E S Audio/Tone Settings Feature Name Tone Tag Call Tone Tag Msg Tone Tag Escalert What it Does Settings Assigns a specic tone to all calls from a specic user
(see page 26 for details). Standard Alert #1 #7 Assigns a specic tone when receiving a specic type of radio call (see page 27 for details). Standard Alert #1 #7 Assigns a specic tone when receiving a specic message (see page 26 for details). Standard Alert #1 #7 Gradually increases the volume of the alarm tones when a call is not answered. Escalert On Escalert Off Companding
(XPand) Approximates the same audio quality for 12.5kHz channels to that of 25kHz channels. Keypad Tones Turns keypad tones on or off. Compand On Compand Off Tones On Tones Off English 42 UTILITIES You can customize some of your radios features by:
1 ) to enter Menu Mode. 2 + or e until UUUUttttiiiilllliiiittttiiiieeeessss 3 ) to select UUUUttttiiiilllliiiittttiiiieeeessss 4 + or e until you see the feature you want to change (see table below). 5 ) to select the feature. You will see the features current setting. 6 + or e for available settings. 7 ) to select the desired setting. Feature Power Level Clock Reminder Alarm Utilities Features What it Does Settings Changes the power level of the radio to high, low, or auto (see page 25). Power High Power Low Sets the time (see page 45). Sets the alarm and turns it on or off (see page 45). Set Time Display Clock Alarm On Alarm Off Set Time I I U T L T E S I 43 English Utilities Features What it Does Allows you to select the language displayed on the display. Activates/deactivates the option board installed in your radio. Displays the radios software version number. Feature Language Selection Option board Software Ver #
Settings English Spanish Portuguese French Opt Board On Opt Board Off I S E T L T U I I English 44 SETTING THE TIME To set the time:
1 ) to enter Menu Mode. 2 + or e until UUUUttttiiiilllliiiittttiiiieeeessss 3 ) to select UUUUttttiiiilllliiiittttiiiieeeessss 4 + or e until CCCClllloooocccckkkk 8 When a setting (e.g., hour) is blinking, you can change it with + or e. Hour
(AM or PM) 3:05 PM Minutes
(AM/PM or 24 hr) 9 f to proceed to the next setting (e.g., from hour to minutes). or until RRRReeeemmmmiiiinnnnddddeeeerrrr AAAAllllaaaarrrrmmmm 10 ) to save your changes. Note: You must access the clock menu to select AM/PM or 24 hr. This selection cannot be made from Reminder Alarm menu. 11 ( to return to CCCClllloooocccckkkk or to return to or RRRReeeemmmmiiiinnnnddddeeeerrrr AAAAllllaaaarrrrmmmm 5 ) to conrm your selection. Hold down ( to exit Menu Mode. 6 + or e until SSSSeeeetttt TTTTiiiimmmmeeee????
7 ) to select SSSSeeeetttt TTTTiiiimmmmeeee????
I I U T L T E S I 45 English DISPLAYING THE TIME To display the time:
1 ) to enter Menu Mode. 2 + or e until UUUUttttiiiilllliiiittttiiiieeeessss 3 ) to select UUUUttttiiiilllliiiittttiiiieeeessss 4 + or e until CCCClllloooocccckkkk 5 ) to conrm your selection. 6 + or e until DDDDiiiissssppppllllaaaayyyy CCCClllloooocccckkkk????
7 ) to select DDDDiiiissssppppllllaaaayyyy CCCClllloooocccckkkk????
The radio will display the time for a preprogrammed duration. 8 ( to exit the menu. SELECTING THE DISPLAY LANGUAGE To select the display language:
1 ) to enter Menu Mode. 2 + or e until UUUUttttiiiilllliiiittttiiiieeeessss 3 ) to select UUUUttttiiiilllliiiittttiiiieeeessss 4 + or e until LLLLaaaannnngggguuuuaaaaggggeeee SSSSeeeelllleeeecccctttt 5 ) to conrm your selection. 6 + or e until desired language is displayed. 7 ) to select desired language. 8 ( to exit the menu. I S E T L T U I I English 46 SAFETY AND WARRANTY European Committee for Electrotechnical Standardisation (CENELEC):
SAFE AND EFFICIENT OPERATION OF MOTOROLA TWO-WAY RADIOS Exposure to Radio Frequency Energy National and International Standards and Guidelines Your Motorola Two-Way Radio, which generates and radiates radio frequency (RF) electromagnetic energy (EME), is designed to comply with the following National and International Standards and Guidelines regarding exposure of human beings to radio frequency electromagnetic energy:
Federal Communications Commission Report and Order No. FCC 96-326 (August 1996) American National Standards Institute
(C95.1 - 1992) National Council on Radiation Protection and Measurements (NCRP - 1986) International Commission on Non-Ionizing Radiation Protection (ICNRP - 1986) ENV. 50166-
1 1995 E Human Exposure to Electromagnetic Fields Low Frequency (0Hz to 10kHz) ENV. 50166-
2 1995 E Proceedings of SC211/8 1996 Human Exposure to Electromagnetic Fields High Frequency (10kHz to 300GHz) Safety Considerations for Human Exposure to E.M.F.s from Mobile Telecommunications Equipment (M.T.E.) in the Frequency Range 30MHz - 6 GHz (E.M.F. -
Electromagnetic Fields) To assure optimal radio performance and that human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards, always adhere to the following procedures:
W A R R A N T Y S A F E T Y A N D 47 English ELECTROMAGNETIC INTERFERENCE/COMPATIBILITY Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise congured for electromagnetic compatibility. To avoid electromagnetic interference and/or compatibility conicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. When instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions. OPERATIONAL WARNINGS Vehicles with an Air Bag
W A R N I N G Do not place a radio in the area over an air bag or in the air bag deployment area. Air bags inate with great force. If a radio is placed in the air bag deployment area and the air bag inates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. Potentially Explosive Atmospheres Turn off your two-way radio when you are in any area with a potentially explosive atmosphere, unless it is a radio type especially qualied for use in such areas (for example, Factory Mutual or CENELEC approved). Sparks in a potentially explosive atmosphere can cause an explosion or re resulting in bodily injury or even death. D N A Y T E F A S Y T N A R R A W English 48 Blasting Caps and Blasting Areas Mobile Radio Operation and EME Exposure To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: Turn off two-way radio. Obey all signs and instructions. Note: The areas with potentially explosive atmospheres referred to above include fueling areas such as: below decks on boats; fuel or chemical transfer or storage facilities; areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you would normally be advised to turn off a vehicle engine. Areas with potentially explosive atmospheres are often but not always posted. To assure optimal radio performance and that human exposure to radio frequency electromagnetic energy is within the guidelines referenced earlier in this document, transmit only when people inside and outside the vehicle are at least the minimum distance away from a properly installed, externally mounted antenna. Table 1 lists the minimum distance for several different ranges of radiated power. Table 1: Radiated Power and Distance Radiated Power of Vehicle-installed Mobile Two-way Radio Minimum Distance From Transmitting Antenna 7 to 15 Watts 1 Foot (30.5 cm) 16 to 50 Watts 2 Feet (61 cm) More than 50 Watts 3 Feet (91.5 cm) W A R R A N T Y S A F E T Y A N D 49 English Mobile Antenna Installation Install the vehicle antenna external to the vehicle and in accordance with:
The requirements of the antenna manufacturer/supplier Instructions in the Radio Installation Manual CONTROL STATION OPERATION When radio equipment is used to operate as a control station, it is important that the antenna be installed outside the building and away from places where people may be in close proximity. Note: Refer to Table on page 49 for rated power and minimum distant values for transmitting antennas. LIMITED WARRANTY MOTOROLA COMMUNICATION PRODUCTS I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:
MOTOROLA INC. (MOTOROLA) warrants the MOTOROLA manufactured Communication Products listed below (Product) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:
_______ Mobile Units Two (2) Years Product Accessories One (1) Year Motorola, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA. D N A Y T E F A S Y T N A R R A W English 50 This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modications to this warranty unless made in writing and signed by an ofcer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product. MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. II. GENERAL PROVISIONS:
This warranty sets forth the full extent of MOTOROLA's responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLAs option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. W A R R A N T Y S A F E T Y A N D 51 English III. STATE LAW RIGHTS:
V. WHAT THIS WARRANTY DOES NOT SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specic legal rights, and there may be other rights which may vary from state to state. IV. HOW TO GET WARRANTY SERVICE:
You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by Motorola through one of its authorized warranty service locations. If you rst contact the company which sold you the Product
(e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call Motorola at 1-800-927-2744 US/Canada. COVER:
A Defects or damage resulting from use of the Product in other than its normal and customary manner. B Defects or damage from misuse, accident, water, or neglect. C Defects or damage from improper testing, operation, maintenance, installation, alteration, modication, or adjustment. D Breakage or damage to antennas unless caused directly by defects in material workmanship. A Product subjected to unauthorized Product modications, disassemblies or repairs (including, without limitation, the addition to the Product of non-Motorola supplied equipment) which adversely affect performance of the Product or interfere with Motorola's normal warranty inspection and testing of the Product to verify any warranty claim. Product which has had the serial number removed or made illegible. E F G Freight costs to the repair depot. D N A Y T E F A S Y T N A R R A W English 52 H A Product which, due to illegal or unauthorized alteration of the software/
rmware in the Product, does not function in accordance with MOTOROLAs published specications or the FCC type acceptance labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA. Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. Normal and customary wear and tear. I J VI. PATENT AND SOFTWARE PROVISIONS:
MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages nally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:
A B that MOTOROLA will be notied promptly in writing by such purchaser of any notice of such claim;
that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and C should the Product or parts become, or in MOTOROLAs opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA. MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof. W A R R A N T Y S A F E T Y A N D 53 English Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such Motorola software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modied in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modication, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights. VII. GOVERNING LAW:
This Warranty is governed by the laws of the State of Illinois, USA. D N A Y T E F A S Y T N A R R A W English 54 ACCESSORIES Motorola offers a number of accessories to enhance the productivity of your two-way radio. Many of the available accessories are listed below. For a complete list, see your Motorola dealer. AUDIO RMN4025 RMN4026 RMN4038 RSN4001 HSN8145 Compact Remote Speaker Microphone Enhanced DTMF Keypad Microphone Heavy Duty Microphone External Speaker 13W External Speaker 7.5W MOUNTING GLN7324 RLN4780 HLN8097 RLN4779 RLN4774 RLN4782 RLN4802 RKN4077 RKN4078 RKN4079 Low Prole Trunnion High Prole Trunnion Removable Slide Mount Key Lock Mount 3 Point Lowband Mount DIN Mounting Kit (in dash) Remote Mount Kit Remote Mount Cable - 3 m Remote Mount Cable - 5 m Remote Mount Cable - 7 m A C C E S S O R E S I 55 English ANTENNAS CONTROL STATION GPN6145 HPN4002 GPN6149 HPN4001 RMN4030 GLN7318 GLN7326 Desktop Power Supply 1-25W (EMC) Desktop Power Supply 1-25W Desktop Power Supply 25-45W (EMC) Desktop Power Supply 25-45W Desktop Microphone Desktop Tray without Speaker Desktop Tray with Speaker Note: A variety of interchangeable buttons are available for use in the P1-P4 locations on your radio (page 5). See your dealer for further details. I S E R O S S E C C A HAD4006 HAD4007 HAD4008 HAD4009 HAD4014 HAE4002 HAE4003 HAE4010 HAE4011 HAE4019 HAE4004 HAE4012 HAE4013 VHF 136-144 MHz, 1/4 Wave Roof Mount VHF 146-150.8 MHz, 1/4 Wave Roof Mount VHF 150.8-162 MHz, 1/4 Wave Roof Mount VHF 162-174 MHz, 1/4 Wave Roof Mount VHF 146-172 MHz, 30dB Gain Roof Mount UHF 403-430 MHz, 1/4 Wave Roof Mount UHF 450-470 MHz, 1/4 Wave Roof Mount UHF 406-420 MHz, 3.5dB Gain Roof Mount UHF 450-470 MHz, 3.5dB Gain Roof Mount UHF 450-470 MHz, 5dB Gain Roof Mount UHF 470-512 MHz, 1/4 Wave Roof Mount UHF 470-494 MHz, 3.5dB Gain Roof Mount UHF 494-512 MHz, 5dB Gain Roof Mount Lowband 29.7-36 MHz Lowband 36-42 MHz Lowband 42-50 MHz HAB9405 RAB4003 RAB4004 09-02105F01 BNC Connector English 56 Sending a Call 1. Turn radio on and select appropriate zone and channel. 2. Press PTT, hold the microphone 1 to 2 inches (2.5 to 5 cm) from your mouth, and speak clearly into it. 3. Release PTT to listen. Receiving a Call 1. Turn radio on and adjust volume to the desired level. 2. Select desired channel. 3. To receive incoming call, press PTT, hold the microphone 1 to 2 inches (2.5 to 5 cm) from your mouth, and speak clearly into it. Deleting a Nuisance Channel During Scanning 1. While radio is on a nuisance channel, hold down preprogrammed Scan button until you hear a tone. 2. Release Scan button. Making a Phone Call 1. Press Phone button, or select Phone from the menu. 2. 3. Send phone number in one of the following ways:
If access code is not displayed, send access code if required. Press and release PTT to send last dialed number. or when using keypad microphone only, press preprogrammed Speed Dial button, followed by a keypad key (18), to access rst nine numbers in your phone list. (Press PTT if buffered dial.) or when using keypad microphone only, enter phone number using the key-
pad. (Press PTT if buffered dial.) 4. Press PTT, hold the microphone 1 to 2 inches (2.5 to 5 cm) from your mouth, and speak clearly into it. Ending a Phone Call 1. Send deaccess code if required. 2. Press preprogrammed Phone button, or press (. Sending and Cancelling an Emergency Alert To activate Emergency Alert., press preprogrammed Emergency button. To cancel, press and hold down Emergency button. Quick Reference Card Record the functions for your radios programmable buttons in the table provided below. For further information, see pages 8 and 9 of this User Guide. On/Off/Volume Knob Red/Yellow/Green LED Indicators LCD Screen Channel Selector/
Menu Navigation Buttons
(Up/Down) Menu Exit/Escape Button Menu Enter/Select Button Programmable Button 3 (P3)
(Interchangeable) Microphone Jack Programmable Button 1 (P1)
(Interchangeable) Programmable Button 2 (P2)
(Interchangeable) Editing Buttons
(Left/Right) Programmable Button 4 (P4)
(Interchangeable) Button Function Short Press Long Press Hold Down Page Menu Navigation Chart
(Refer to Menu Navigation guidelines lower, left-hand corner of this page)
+ e System Scan
(p. 29) Program Lists Phone
(p. 35)
+ e on/off
+ e Radio Call
(p. 19)
+ e Zone
(p. 16) Message Message Status Utilities p. 43) Rptr/
Talkarnd
(p. 25) Audio/
Tones
(p. 41) select/
select/
enter ID enter ID select/
enter ID
+ e + e + e repeater mode/
talkarnd mode Scan List
(p. 30) Phone List
(p. 36) RadioCall List
(p. 24) edit entry add/delete entry edit priority all/delete/edit entry/edit codes Selective Call Call Alert Radio Check select/
enter ID select/
enter ID select/
enter ID Menu Navigation
) to enter Menu Mode.
+ or e to scroll through the list.
) to select Menu item.
( to return to previous menu level or Hold down ( to exit Menu Mode.
+ or e to scroll through sub-list.
) to select sub-menu item. Power Level high/low/
auto Clock display/
set time Reminder Alarm on/off/
set time Language Select select Option Board on/off Light Disable on/off Software Ver #
Alert Vol Lvl on/off Tone Disable on/off Name Tone Tag standard/alert
#1 - #7 Message Tone/Tag standard/alert
#1 - #7 Call Tone Tag standard/alert
#1 - #7 Escalert on/off Companding on/off Keypad Tones on/off
1 2 | users Manual (revised) | Users Manual | 834.29 KiB |
CONTENTS Computer Software Copyrights. iii Radio Overview . 1 Parts of the Radio . 1 Optional Enhanced Keypad Microphone (RMN4026) . 2 On/Off/Volume Knob . 3 Channel Selector/Menu Navigation Buttons . 3 LED Indicators . 3 Programmable Buttons . 3 Push-to-Talk (PTT) Button . 6 Microphone . 6 Menu Keys . 6 Use with Enhanced Keypad Microphone (RMN4026) . 7 LCD Screen . 9 Audio Indicators for Programmable Buttons. 10 Getting Started . 11 Turning the Radio On or Off . 11 Adjusting the Volume . 11 Selecting a Zone . 12 Selecting a Radio Channel . 12 Sending a Call . 13 Receiving a Call . 13 Radio Calls . 15 Making a Selective Call . 15 Receiving a Selective Call . 15 Sending a Call Alert Page. 16 Receiving a Call Alert Page . 16 Radio Check . 17 Sending a Status . 17 Sending a Message . 18 Receiving a Message . 19 Sending an Emergency Alert . 19 Selective Radio Inhibit . 20 Editing a Radio Call List . 20 Repeater or Talkaround Mode . 21 Setting the Power Level . 21 Name and Call/Message Tone Tagging . 22 Scan . 25 Starting or Stopping Scan. 25 Talkback . 26 Deleting a Nuisance Channel . 26 Restoring a Channel to the Scan List . 26 Editing a Scan List . 26 Adding or Deleting Channels in a Scan List . 27 C O N T E N T S i English S T N E T N O C Exposure to Radio Frequency Energy . 43 Mobile Radio Operation and EME Exposure . 44 Electromagnetic Interference/
Compatibility . 44 Operational Warnings . 45 Vehicles with an Air Bag . 45 Potentially Explosive Atmospheres. 45 Blasting Caps and Blasting Areas. 45 ANTENNA INSTALLATION . 46 MOBILE ANTENNAS . 46 FIXED SITE ANTENNAS . 46 Limited Warranty . 47 Accessories . 51 Audio . 51 Mounting . 51 Antennas . 52 Control Station . 52 Prioritizing a Channel in a Scan List . 28 Setting Priority Channels . 28 Phone. 31 Making a Phone Call . 31 Modifying the Phone List . 32 Adding an Entry (when using the enhanced keypad microphone only). 32 Deleting an Entry . 33 Editing an Entry (when using the enhanced keypad microphone only). 34 Editing an Access/Deaccess Code
(when using the enhanced keypad microphone only). 35 Audio/Tone Settings. 37 Utilities. 39 Setting the Time . 41 Displaying the Time . 42 Selecting the Display Language . 42 Safety and Warranty. 43 Safe and Efficient Operation of Motorola Two-Way Radios . 43 English ii COMPUTER SOFTWARE COPYRIGHTS The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modied, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. C O N T E N T S iii English S T N E T N O C English iv RADIO OVERVIEW PARTS OF THE RADIO On/Off/Volume Knob Red/Yellow/Green LED Indicators LCD Screen Channel Selector/
Menu Navigation Buttons
(Up/Down) Menu Exit/Escape Button Menu Enter/Select Button Programmable Button 3 (P3)
(Interchangeable) I R A D O O V E R V E W I Microphone Jack Programmable Button 1 (P1)
(Interchangeable) Programmable Button 2 (P2)
(Interchangeable) Editing Buttons
(Left/Right) Programmable Button 4 (P4)
(Interchangeable) 1 English Optional Enhanced Keypad Microphone
(RMN4026) Your radio may be ordered with an optional DTMF (Dual-Tone Multi-Frequency) microphone that has a direct entry keypad. This enhanced keypad microphone has three buttons (A, B, C) below the keypad that can be programmed to conveniently activate select radio features. Push-to-Talk
(PTT) button Keypad Programmable Buttons
(A, B, C) FL0830328O I W E V R E V O O D A R I English 2 On/Off/Volume Knob Turns the radio on or off, and adjusts the radios volume. Channel Selector/Menu Navigation Buttons y or z Used for channel scrolling. When in menu mode, used for menu navigation. LED Indicators Indicates channel, scan, and monitor status, as well as receipt of a selective call. Programmable Buttons Your radio has several programmable buttons. Your dealer can program these buttons as shortcuts to various radio features. Check with your dealer for a complete list of functions your radio supports. Programmable buttons include the i buttons (see page 1).
, and j g h
, Some buttons can access up to two features, depending on the type of button press:
short press quickly pressing and releasing the programmable buttons pressing and holding the long press programmable buttons for a period of time
(default 1 1/2 seconds or programmed value) hold down pressing and holding down the programmable buttons while checking status or making adjustments A summary of programmable radio features and corresponding page references appears beginning on page 4. In the Button column, have your dealer record the name of the programmable button next to the feature that has been programmed to it. The dealer can use the abbreviations (P1, P2, P3, P4) shown in the radio illustration on page 1. Also, where appropriate, have your dealer indicate whether the button press requires a short press, a long press, or needs to be held down. I R A D O O V E R V E W I 3 English Function Indicator Short Press Long Press Volume Set Direct Zone Access Home Revert Direct Channel Access PRTT (Priority Request-to-Talk) Direct entry to zone selection menu. Takes you directly to a pre-programmed zone/channel combination. Toggle the direct access channel feature.
(Enhanced keypad microphone required.) Sends a priority access request to the dispatcher. Emergency E Initiate Emergency Alert. Cancel Emergency status. Power Level Repeater/
Talkaround Scan/Nuisance Channel Delete B J G Toggle transmit power level between High and Low. Toggle between using a repeater or transmitting directly to another radio. Delete a nuisance channel while scanning. Toggle scan on and off. I W E V R E V O O D A R I Phone This function is activated by D Access Phone Mode. EITHER a short OR a long press, but not both. Hold Down Page Button Sound a tone for adjusting your radios volume level. 11 12 13 13 13 19 21 21 25 31 English 4 Function Indicator Short Press Long Press Hold Down Page Button Speed Dial Access your phone list directly. Monitor Option Board
(if one is installed) Radio Call Light Auxiliary Control (1/2) Status One-Touch Status Message One-Touch Message Horn and Lights Toggle silent monitor operation (also turn off open squelch monitor when it has been activated). Turn on open squelch monitor. Toggle between activating and deactivating the option board. Access the radio call menu. Adjust brightness level (off/low/med/high). Activates or deactivates a pin on the accessory connector.
(See your dealer.) Direct entry to the status menu. Immediately sends a preprogrammed status. Direct entry to the message menu. Immediately sends a preprogrammed message. Toggles external alarm feature or cancels a triggered alarm. C N 31 I R A D O O V E R V E W I This function is activated by EITHER a short OR a long press, but not both. 5 English Up Key y and Down Key z Used for channel scrolling. When in Menu Mode, used for menu navigation. Right Key w Moves the cursor right or inserts a space when editing or Zone scrolling. Left Key v Moves the cursor left or used as a backspace key when editing or Zone scrolling. I W E V R E V O O D A R I Push-to-Talk (PTT) Button Press and hold down this button to talk;
release it to listen. Microphone Hold the microphone 1 to 2 inches (2.5 to 5 cm) from your mouth, and speak clearly into it. Menu Keys Menu/
Exit Select t y u Up v z w Left Right Down Menu/Select Key u Used to enter Menu Mode. When in Menu Mode, this key is also used to make menu selections. Exit Key t Used to move to the previous Menu level (short press) or to exit Menu Mode (long press). English 6 Use with Enhanced Keypad Microphone
(RMN4026
) These keys are used to:
Dial a phone number Make a radio call Enter information when programming radio lists Directly access preprogrammed features Each key can generate several different characters. For example, to enter the character C, press the following table.) key three times. (Refer to the 2 I R A D O O V E R V E W I 7 English Entering Characters Using the Keypad Number of Times Key is Pressed Key 0 1 2 3 4 5 6 7 8 1 0 1 A D G J M P T 9 W
2
B E H K N Q U X
Blank Space 3
) 4
C F I L O R V Y
2 3 4 5 6 S 8 Z
. 5
a d g j m 7 t 9
6 7 8 9 10 11 12 13 14 15 16 17 b e h k n p u w
c f i l o q v x 2 3 4 5 6 r 8 y s z 7 9 Y y
I W E V R E V O O D A R I English 8 LCD Screen The top screen row displays radio status information:
Symbol A Companding B Power Level C Carrier Squelch
(CSQ) Indication The Companding feature is activated. When in narrow band, this feature improves audio quality. Low Power R or High Power S is activated. The radio is on a CSQ channel, monitor is active, or the microphone is off-hook. Symbol D Phone E Emergency F Call Received G Scan Priority 1 Scan ashing)
H Priority 2 Scan
steady) Indication Phone Mode is selected. An Emergency Alert is being sent. A Selective Call or Call Alert has been received. The Scan feature is active. Flashes when Scan is suspended. During Scan, indicates that the scan has locked on to a priority 1 channel. During Scan, indicates that the scan has locked on to a priority 2 channel. I R A D O O V E R V E W I 9 English Symbol J Talkaround K Programming Mode M Signal Strength N Option Board Indication The radio is not transmitting through a repeater. The radio is in Program List editing mode. Indicates signal strength. The more bars, the stronger the signal. Option board is enabled. Q L Not currently assigned. Not currently assigned. AUDIO INDICATORS FOR PROGRAMMABLE BUTTONS Low-High Tone High-Low Tone In addition to having associated visual indicators, some programmable buttons use tones to indicate one of two modes:
Button Low-High Tone High-Low Tone Scan Power Level Start scan High power selected Stop scan Low power selected Option Board Enabled Disabled Repeater/
Talkaround Does not use repeater Uses repeater I W E V R E V O O D A R I English 10 ADJUSTING THE VOLUME Turn the On/Off/Volume Control knob clockwise to increase the volume, or counterclockwise to decrease the volume. or 1 Hold down the Volume Set button (see page 4). You will hear a continuous tone. 2 Turn the On/Off/Volume Control knob to the desired volume level. 3 Release the Volume Set button. GETTING STARTED TURNING THE RADIO ON OR OFF OFF Push the On/Off/
Volume Control knob until you hear a click and the display clears. ON Push the On/Off/
Volume Control knob until you hear a click. If power-up is successful, you will hear the Self-Test Pass Tone. If the radio fails to power up, you will hear the Self-Test Fail Tone
. I G E T T N G S T A R T E D 11 English SELECTING A ZONE A zone is a group of up to 16 channels. Before you can access a channel in a zone, you must select the zone in one of three ways:
Method 1 1 u to enter Menu Mode. 2 y or z until 3 u to select ZZZZoooonnnneeee ZZZZoooonnnneeee 4 y or z until you see the desired zone name. 5 u to select the zone. Method 2 (if programmed by your dealer [see pages 4-5]). 1 Press the Direct Zone Access button. 2 y or z until you reach the desired zone. 3 u to select the zone. Method 3 Press v to select the previous zone. If pressed while the rst zone is selected, the radio will wrap around to the last zone.
-or-
Press w to select the next zone. If pressed while the last zone is selected, the radio will wrap around to the rst zone. SELECTING A RADIO CHANNEL Your radio offers 128 channels (8 zones of 16 channels each). Note: Due to government regulations, some channels may not be programmed. See your dealer for more information. There are three ways to select a channel:
Method 1 1 Select the appropriate Zone, if required. 2 y or z until you reach the desired channel, shown on the screen. D E T R A T S G N T T E G I English 12 Method 2 (if programmed by your dealer [see pages 4 -5]). If your system uses the request-to-talk feature, use the following method to send a call:
1 Press the Home Revert button. 1 Turn your radio on. Method 3 (if programmed by your dealer [see pages 4 -5]). 1 Press the Direct Channel Access button. 2 Enter the desired channel using the enhanced keypad microphone. 2 y or z to select the desired channel. 3 Press the PTT (for priority requests to talk, the PRTT button) and wait for the talk permit tone. 4 Hold the microphone vertically 1 to 2 inches
(2.5 to 5 cm) from your mouth. Press the PTT to talk; release it to listen. 3 u to conrm your selection. 5 Release the PTT to listen. SENDING A CALL 1 Turn your radio on. 2 y or z to select the desired channel. 3 Hold the microphone vertically 1 to 2 inches
(2.5 to 5 cm) from your mouth. Press the PTT to talk; release it to listen. RECEIVING A CALL 1 2 3 4 Turn your radio on. Adjust the radios volume if necessary (see page 11). Select the desired channel. To respond, hold the microphone vertically 1 to 2 inches (2.5 to 5 cm) from your mouth. Press the PTT to talk; release it to listen. I G E T T N G S T A R T E D 13 English Notes D E T R A T S G N T T E G I English 14 I R A D O C A L L S RADIO CALLS MAKING A SELECTIVE CALL You can make a selective call to a particular radio or group of radios, provided the signaling protocol supports it. To make a Selective Call:
1 u to enter Menu Mode. 2 y or z until RRRRaaaaddddiiiioooo CCCCaaaallllllll 3 u to select RRRRaaaaddddiiiioooo CCCCaaaallllllll 4 y or z until SSSSeeeelllleeeeccccttttiiiivvvveeee CCCCaaaallllllll 5 u to select SSSSeeeelllleeeeccccttttiiiivvvveeee CCCCaaaallllllll 6 y or z to locate the desired ID in the Radio Call List. or when using the enhanced keypad microphone only, enter the ID number of the radio you want to call. 7 8 Press the PTT to send the call. The radio sounds a continuous tone. Press the PTT to talk; release it to listen. 9 When nished with the call, t to return to or Hold down t to exit Menu Mode. SSSSeeeelllleeeeccccttttiiiivvvveeee CCCCaaaallllllll RECEIVING A SELECTIVE CALL F When you receive a selective call:
You will hear two alert tones. The LED Indicator ashes yellow. The LCD screen displays F and the preprogrammed name or ID of the calling radio, if available. 15 English S L L A C O D A R I SENDING A CALL ALERT PAGE You can alert another person by sending a Call Alert page. To send a Call Alert page:
1 u to enter Menu Mode. 2 y or z until RRRRaaaaddddiiiioooo CCCCaaaallllllll 3 u to select RRRRaaaaddddiiiioooo CCCCaaaallllllll 4 y or z until CCCCaaaallllllll AAAAlllleeeerrrrtttt 5 ) to select CCCCaaaallllllll AAAAlllleeeerrrrtttt 6 y or z to locate the desired ID in the Radio Call List;
or when using the enhanced keypad microphone only, enter the ID number of the radio you want to page. 7 Press the PTT to send the page. You will see CCCCaaaallllllll IIIInnnn PPPPrrrroooogggg 8 If the Call Alert page is received, you will see If not, you will see AAAAcccckkkknnnnoooowwwwlllleeeeddddggggeeee NNNNoooo AAAAcccckkkknnnnoooowwwwlllleeeeddddggggeeee 9 t to return to CCCCaaaallllllll AAAAlllleeeerrrrtttt or Hold down t to exit Menu Mode. RECEIVING A CALL ALERT PAGE When your radio receives a Call Alert page, it sounds four alert tones continuously and the following are displayed until you respond:
the F symbol, and the ID of the calling radio alternating with Call Received. Press the PTT to answer the page, or press any other key to clear it. Note: Your radio will display only the last Call Alert page received. Also, your radio will not receive any Selective Calls until you clear the page. English 16 RADIO CHECK This feature allows you to determine if a radio is in range without disturbing the user of the radio. Radio Check can also be used when attempts with Selective Call and Call Alert fail.
(This feature is available only if your signaling protocol supports it.) To perform a Radio Check:
1 u to enter Menu Mode. 2 y or z until RRRRaaaaddddiiiioooo CCCCaaaallllllll 3 u to select RRRRaaaaddddiiiioooo CCCCaaaallllllll 4 y or z until RRRRaaaaddddiiiioooo CCCChhhheeeecccckkkk 5 u to select RRRRaaaaddddiiiioooo CCCChhhheeeecccckkkk 6 y or z to locate the desired ID in the Radio Call List;
or when using the enhanced keypad microphone only, enter the ID number of the radio you are checking. 7 8 Press the PTT. You will see CCCCaaaallllllll IIIInnnn PPPPrrrroooogggg If the Radio Check is received, you will see AAAAcccckkkknnnnoooowwwwlllleeeeddddggggeeee If not, you will see NNNNoooo AAAAcccckkkknnnnoooowwwwlllleeeeddddggggeeee I R A D O C A L L S 9 t to return to RRRRaaaaddddiiiioooo CCCChhhheeeecccckkkk RRRRaaaaddddiiiioooo CCCChhhheeeecccckkkk or Hold down t to exit Menu Mode. SENDING A STATUS This feature gives you the ability to send a status update to the base. The status feature makes more efcient use of the channel compared to voice transmissions. Status updates of up to 14 characters may be programmed by your dealer. To send a Status:
1 u to enter Menu Mode. 2 y or z until 3 u to select SSSSttttaaaattttuuuussss SSSSttttaaaattttuuuussss 17 English S L L A C O D A R I 4 y or z to locate the desired status in the preprogrammed list. or when using the enhanced keypad microphone only, enter the number of the status you wish to send. or if programmed by your dealer (see pages 4-5), press the button that has been preprogrammed for a specic status. Note: You cannot retransmit the current status update. SENDING A MESSAGE This feature gives you the ability to send and receive preprogrammed messages. Data messages make more efcient use of channels compared to voice transmissions. Messages of up to 14 characters may be programmed by your dealer. To send an electronic (data) message:
1 u to enter Menu Mode. 2 y or z until MMMMeeeessssssssaaaaggggeeee 3 u to select MMMMeeeessssssssaaaaggggeeee 4 y or z to locate the desired message in the preprogrammed list. or when using the enhanced keypad microphone only, enter the number of the message you wish to send. or if programmed by your dealer (see pages 4-5), press the button that has been preprogrammed for a specic message. English 18 I R A D O C A L L S Emergency Alerts have priority over all other calls. The E symbol will appear on the display when your radio is in the Emergency Alert state. An Emergency Alert can be programmed to:
Show E and sound a tone or Show E (Silent Emergency) or Activate the microphone so that all activity can be transmitted (for a predetermined amount of time). See your dealer for more information. To cancel the Emergency Alert, press and hold down the Emergency button. RECEIVING A MESSAGE When your radio receives a message:
You will hear two alert tones. The yellow LED indicator ashes. The LCD screen displays alternating with the preprogrammed alias. MMMMssssgggg RRRReeeecccceeeeiiiivvvveeeedddd Note: If you receive a message that is programmed into your radio, the display will alternate with the following:
MMMMeeeessssssssaaaaggggeeee ####____ and NNNNoooo AAAAlllliiiiaaaassss SENDING AN EMERGENCY ALERT E A priority Emergency Alert can be sent to a specic radio or dispatch center by pressing:
A button preprogrammed by your dealer
(see pages 4-5). The footswitch A pushbutton accessory 19 English S L L A C O D A R I SELECTIVE RADIO INHIBIT Your radio is equipped with a security feature that can temporarily render the unit inoperative when an inhibit signal is sent from the base station. This feature is commonly used to disable radios:
When your vehicle is being serviced For system control reasons Note: When your radio has been disabled by In case of theft the base station, all controls will be inoperative except for the On/Off button. When the radio is powered up, the display will show:
RRRRaaaaddddiiiioooo DDDDiiiissssaaaabbbblllleeeedddd EDITING A RADIO CALL LIST K The ID numbers in your Radio Call List are preprogrammed by your dealer. However, you can edit the names associated with these IDs using the enhanced keypad microphone. The K symbol will appear on the display when you are editing. Note: Your radio cannot receive any calls while you are editing. To edit a Call List entry:
1 u to enter Menu Mode. 2 y or z until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 3 u to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 y or z until RRRRaaaaddddiiiiooooCCCCaaaallllllll LLLLiiiisssstttt 5 u to select RRRRaaaaddddiiiiooooCCCCaaaallllllll LLLLiiiisssstttt 6 y or z until EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
7 u to select EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
8 y or z until you locate the desired entry. 9 u to select the entry. 10 Use your keypad to edit the entry (see page 7). 11 u to save your changes. You will see EEEEnnnnttttrrrryyyy SSSSaaaavvvveeeedddd English 20 I R A D O C A L L S 12 t to return to EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
or Hold down t to exit Menu Mode. REPEATER OR TALKAROUND J MODE Talkaround Mode enables you to communicate with another radio when either:
The repeater is not operating. or Your radio is out of the repeaters range but within communicating distance of another radio. The J symbol appears on the display when Talkaround Mode is selected. To select either Repeater Mode or Talkaround Mode:
Press the preprogrammed Repeater/
Talkaround button (see page 4) to toggle between Repeater Mode and Talkaround Mode. or 1 u to enter Menu Mode. 2 y or z until RRRRppppttttrrrr////TTTTaaaallllkkkkaaaarrrrnnnndddd 3 u to select RRRRppppttttrrrr////TTTTaaaallllkkkkaaaarrrrnnnndddd 4 y or z until RRRReeeeppppeeeeaaaatttteeeerrrr MMMMooooddddeeee or until TTTTaaaallllkkkkaaaarrrrnnnndddd MMMMooooddddeeee 5 u to conrm your selection. SETTING THE POWER LEVEL B Each channel in your radio has a predened transmit power level that can be changed. High power ( S ) Low power ( R ) You can set the power level in two ways:
Method 1 Press the preprogrammed Power Level button
(see page 4) to toggle between low and high. or Method 2 1 u to enter Menu Mode. 21 English S L L A C O D A R I 2 y or z until UUUUttttiiiilllliiiittttiiiieeeessss 3 u to select UUUUttttiiiilllliiiittttiiiieeeessss 4 y or z until PPPPoooowwwweeeerrrr LLLLeeeevvvveeeellll 5 u to select PPPPoooowwwweeeerrrr LLLLeeeevvvveeeellll The display shows the current power level. 6 y or z until PPPPoooowwwweeeerrrr HHHHiiiigggghhhh????
or until PPPPoooowwwweeeerrrr LLLLoooowwww????
7 u to conrm the selection. NAME AND CALL/MESSAGE TONE TAGGING You can program your radio to sound a particular alert tone when:
a specic user is callingname tone tagging, or a message is being sent to your radio, or your radio is receiving a type of radio call call tone tagging. There are seven alert tones to select from. To tag a specic users name or message:
1 u to enter Menu Mode. 2 y or z until AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss 3 u to select AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss 4 y or z until NNNNaaaammmmeeee TTTToooonnnneeee TTTTaaaagggg or 5 u to select MMMMssssgggg TTTToooonnnneeee TTTTaaaagggg NNNNaaaammmmeeee TTTToooonnnneeee TTTTaaaagggg or MMMMssssgggg TTTToooonnnneeee TTTTaaaagggg 6 y or z until you see the name or message you want to tag. 7 u to conrm the selection. 8 y or z until you hear one of the seven tones you want to use for this name or message. 9 u to conrm the selection. You will see or NNNNaaaammmmeeee TTTTaaaagggg SSSSeeeetttt MMMMssssgggg TTTToooonnnneeee TTTTaaaagggg English 22 I R A D O C A L L S 10 t to return to NNNNaaaammmmeeee TTTToooonnnneeee TTTTaaaagggg 9 u to conrm the selection. You will see CCCCaaaallllllll TTTToooonnnneeee TTTTaaaagggg 10 t to return to CCCCaaaallllllll TTTToooonnnneeee TTTTaaaagggg or Hold down t to exit Menu Mode. MMMMssssgggg TTTToooonnnneeee TTTTaaaagggg or or Hold down t to exit Menu Mode. To tag a type of radio call:
1 u to enter Menu Mode. 2 y or z until AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss 3 u to select AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss 4 y or z until CCCCaaaallllllll TTTToooonnnneeee TTTTaaaagggg 5 u to select CCCCaaaallllllll TTTToooonnnneeee TTTTaaaagggg 6 y or z until you see the call type you want to tag. 7 u to conrm the selection. 8 y or z until you hear the tone you want to use for this type of call. 23 English Notes S L L A C O D A R I English 24 You can start or stop a scan operation either by:
pressing the preprogrammed Scan button (see page 4) to start or stop scanning;
or 1 ) to enter Menu Mode. 2 y or z until SSSSyyyysssstttteeeemmmm SSSSccccaaaannnn 3 ) to select SSSSyyyysssstttteeeemmmm SSSSccccaaaannnn 4 y or z until SSSSyyyyssss SSSSccccaaaannnn OOOOnnnn????
or SSSSyyyyssss SSSSccccaaaannnn OOOOffffffff????
5 ) to conrm your selection. S C A N SCAN Your radio can monitor multiple channels in a scan list. Your dealer can program up to 16 different channels into each scan list. When your radio detects activity on a scan list channel, it will automatically switch to that channel. Note: The same channels can be assigned to different scan lists. STARTING OR STOPPING SCAN G The Gsymbol, and the number of the channel you are transmitting on, will appear on the display when you start a scan operation. The green LED indicator blinks during a scan operation and stops blinking when the radio switches to a channel. Note: If you enter Menu Mode while the radio is scanning, scanning will stop. It will resume when you exit Menu Mode. 25 English N A C S TALKBACK The Talkback feature allows you to respond to a transmission while scanning. If a transmission on a channel is detected while scanning, the radio will stop on that channel for a preprogrammed period of time. During this hangtime you may respond by pressing the PTT. Note: If transmission stops/ceases or if the PTT is not pressed for a preprogrammed duration, the radio will continue scanning. Also, the LED scan indicator stops blinking while the radio is in hangtime. DELETING A NUISANCE CHANNEL If a channel continually generates unwanted calls or noise (a nuisance channel), use the Scan button to temporarily delete the channel from the scan list. Note: You cannot delete a priority channel (see page 28) or the last remaining channel in a scan list. 1 While the radio is on the nuisance channel, hold down the Scan button until you hear a tone. 2 Release the Scan button. The nuisance channel is deleted. Restoring a Channel to the Scan List To restore a previously deleted channel to the scan list, restart the scan operation or turn your radio off and on again. EDITING A SCAN LIST A scan list is a group of up to 16 channels. Each channel can have a scan list assigned to it. The same channel can be included in several scan lists, and the same scan list can be assigned to several Channel Selector positions. For example:
Position 2 Position 14 C h a n n e l s 1 3 5 6 1 2 3 11 When you edit a scan list, you can either add, delete, or prioritize channels. The K symbol will appear on the display while you are in edit mode. Note: Your radio cannot receive any calls while you are editing a scan list. English 26 Adding or Deleting Channels in a Scan List To add or delete channels in a scan list:
1 ) to enter Menu Mode. 2 y or z until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 y or z until SSSSccccaaaannnn LLLLiiiisssstttt 5 ) to select SSSSccccaaaannnn LLLLiiiisssstttt 6 y or z until AAAAdddddddd EEEEnnnnttttrrrryyyy????
or until DDDDeeeelllleeeetttteeee EEEEnnnnttttrrrryyyy????
7 ) to conrm your selection. 8 y or z until you see the channel you want to add or delete. Note: You cannot delete the last remaining channel in a scan list. 9 ) to conrm your selection. 10 If you added a channel, EEEEnnnnttttrrrryyyy SSSSaaaavvvveeeedddd you will see or If you deleted a channel, you will see
) to conrm the deletion. You will see DDDDeeeelllleeeetttteeee????
EEEEnnnnttttrrrryyyy DDDDeeeelllleeeetttteeeedddd 11 ( to return to AAAAdddddddd EEEEnnnnttttrrrryyyy????
or to return to or Hold down ( to exit Menu Mode. DDDDeeeelllleeeetttteeee EEEEnnnnttttrrrryyyy????
S C A N 27 English Prioritizing a Channel in a Scan List Setting Priority Channels You may want to check the activity on one or two channels more frequently than others. You can do this by assigning them priority:
Note: Even if there may be activity on a non-
priority channel, your radio will automatically switch to an active priority channel and indicate the activity with a short tone. N A C S Priority Channel Scanning Sequence None specied Ch1 Ch2 Ch3 Ch4 Ch1 Channel 2
(Priority 1) Channel 2
(Priority 1) Channel 8
(Priority 2) Ch2 Ch1 Ch2 Ch3 Ch2 Ch4 Ch2 Ch1 Ch2 Ch1 Ch8 Ch3 Ch2 Ch4 Ch8 Ch1 Note: You cannot reprioritize a Priority 1 channel to Priority 2. 1 ) to enter Menu Mode. 2 y or z until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 y or z until SSSSccccaaaannnn LLLLiiiisssstttt 5 ) to select SSSSccccaaaannnn LLLLiiiisssstttt 6 y or z until EEEEddddiiiitttt PPPPrrrriiiioooorrrriiiittttyyyy????
7 ) to select EEEEddddiiiitttt PPPPrrrriiiioooorrrriiiittttyyyy????
8 y or z until PPPPrrrriiiioooorrrriiiittttyyyy ####1111????
or until PPPPrrrriiiioooorrrriiiittttyyyy ####2222????
9 ) to select the desired priority level. 10 y or z until you see the channel you want to prioritize. English 28 11 ) to prioritize that channel. 12 ( to return to EEEEddddiiiitttt PPPPrrrriiiioooorrrriiiittttyyyy????
or Hold down ( to exit Menu Mode. Note: If you want to reprioritize all channels, you must rst delete each priority channel from the scan list, and then add it back. S C A N 29 English Notes N A C S English 30 PHONE If your radio has access to a telephone system, you can make a phone call. To do this, your radio must send an access code to a station that connects it to a phone line. (Ask your dealer for more details.) After completing a call, your radio must send a deaccess code to hang up. MAKING A PHONE CALL D You can make a phone call using the preprogrammed Phone button (see page 4) or the radio menu. The D symbol appears on the display when you are in Phone Mode. To initiate a phone call:
Press the Phone button. or Do the following:
1 Switch to the desired channel. 2 ) to enter Menu Mode. 3 y or z until PPPPhhhhoooonnnneeee 4 ) to select PPPPhhhhoooonnnneeee 5 You will hear a series of tones indicating that an access code is being sent automatically. You will also see your access code displayed;
or when using the keypad microphone only, enter your access code using the keypad. 6 When you hear a dial tone, enter or select a phone number:
when using the keypad microphone only, enter the phone number using the keypad. or y or z to select a number from the phone list. or when using the keypad microphone only, a Press and release the preprogrammed Speed Dial button (see page 5) to use the Speed Dial feature. b Press the key (1 to 8) corresponding to the number you want to call, or press 0 if you want to call the last number dialed. P H O N E 31 English Note: To redial the last number dialed (if not using Speed Dial), do not choose a number. Proceed to step 7. Alternatively, if you entered your access code using the keypad, press z once to access the last number dialed; then press and release the PTT. 7 8 To end a phone call, do one of the following:
If your radio has the deaccess code preprogrammed, proceed to step 8. or Enter the deaccess code using the keypad. Press the Phone button to exit Phone Mode. or
( to exit Phone Mode and return to PPPPhhhhoooonnnneeee or Hold down ( to exit Menu Mode. MODIFYING THE PHONE LIST K You can modify a phone list in one of the following ways:
Add an entry Delete an entry Edit an existing entry Edit an Access/Deaccess code When you are modifying the phone list, the K symbol will appear on the display. Note: Your radio cannot receive any calls while you are modifying the phone list. Adding an Entry (when using the enhanced keypad microphone only) To add an entry:
1 ) to enter Menu Mode. 2 y or z until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 y or z until PPPPhhhhoooonnnneeee LLLLiiiisssstttt 5 ) to select PPPPhhhhoooonnnneeee LLLLiiiisssstttt E N O H P English 32 6 y or z until AAAAdddddddd EEEEnnnnttttrrrryyyy????
14 ( to return to AAAAdddddddd EEEEnnnnttttrrrryyyy????
7 ) to select AAAAdddddddd EEEEnnnnttttrrrryyyy????
You will see EEEEnnnntttteeeerrrr NNNNaaaammmmeeee 8 Use the keypad to enter the name (see page 7). or Hold down ( to exit Menu Mode. Deleting an Entry To delete an entry:
9 ) to store the name. 1 ) to enter Menu Mode. You will see EEEEnnnntttteeeerrrr PPPPhhhhoooonnnneeee ####
2 y or z until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 10 Use the keypad to enter the phone number. You can also add a dash (press w) and a Pause Indicator (hold down # until the #
character on the display changes to a P). 11 ) to select the phone number. 12 y or z until you see the location in the list where you want to store the phone number. 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 y or z until PPPPhhhhoooonnnneeee LLLLiiiisssstttt 5 ) to select PPPPhhhhoooonnnneeee LLLLiiiisssstttt 6 y or z until DDDDeeeelllleeeetttteeee EEEEnnnnttttrrrryyyy????
7 ) to select DDDDeeeelllleeeetttteeee EEEEnnnnttttrrrryyyy????
13 ) to store the phone number. 8 y or z until you see the entry you want You will see EEEEnnnnttttrrrryyyy SSSSaaaavvvveeeedddd to delete. P H O N E 33 English 9 ) to select the entry. 8 y or z until you see the entry you want to DDDDeeeelllleeeetttteeee????
You will see
) again to conrm the deletion. You will see EEEEnnnnttttrrrryyyy DDDDeeeelllleeeetttteeeedddd 10 ( to return to DDDDeeeelllleeeetttteeee EEEEnnnnttttrrrryyyy????
or Hold down ( to exit Menu Mode. Editing an Entry (when using the enhanced keypad microphone only) To edit an entry:
1 ) to enter Menu Mode. 2 y or z until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss edit. 9 ) to select the entry. EEEEddddiiiitttt NNNNaaaammmmeeee????
10 y or z until to edit the name, or until to edit the phone number, or until to edit the location in the phone list. EEEEddddiiiitttt NNNNuuuummmmbbbbeeeerrrr????
EEEEddddiiiitttt LLLLooooccccaaaattttiiiioooonnnn????
11 ) to conrm your selection. 12 Use the keypad to edit the entry (see page 7). or y or z until you see the location where you want to store the phone number. E N O H P 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 13 ) to store the information. 4 y or z until PPPPhhhhoooonnnneeee LLLLiiiisssstttt 14 ( to return to EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
5 ) to select PPPPhhhhoooonnnneeee LLLLiiiisssstttt 6 y or z until EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
7 ) to select EEEEddddiiiitttt EEEEnnnnttttrrrryyyy????
or Hold down ( to exit Menu Mode. English 34 10 y or z to edit another code. or Hold down ( to exit Menu Mode. Editing an Access/Deaccess Code (when using the enhanced keypad microphone only) To edit an access/deaccess code:
1 ) to enter Menu Mode. 2 y or z until PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 3 ) to select PPPPrrrrooooggggrrrraaaammmm LLLLiiiissssttttssss 4 y or z until EEEEddddiiiitttt CCCCooooddddeeeessss????
5 ) to select EEEEddddiiiitttt CCCCooooddddeeeessss????
6 y or z until AAAAcccccccceeeessssssss CCCCooooddddeeee????
or until DDDDeeeeaaaacccccccceeeessssssss CCCCooooddddeeee????
7 ) to select AAAAcccccccceeeessssssss CCCCooooddddeeee????
or DDDDeeeeaaaacccccccceeeessssssss CCCCooooddddeeee????
8 Enter the number using the enhanced keypad microphone. 9 ) to select the entry. P H O N E 35 English Notes E N O H P English 36 S E T T N G S I I A U D O T O N E
AUDIO/TONE SETTINGS You can customize the audio and tone feature settings on your radio. 1 ) to enter Menu Mode. 2 y or z until AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss 3 ) to select AAAAuuuuddddiiiioooo////TTTToooonnnneeeessss 4 y or z until you see the feature you want to change. (Refer to the table below.) 5 ) to select the feature. You will see the features current setting. 6 y or z for available settings. (Refer to the table below.) 7 ) to select the desired setting. Audio/Tone Settings Feature Alert Vol Lvl What it Does Settings Allows the volume level of the audio and the volume level of the alert tones to be set independently. Ind Alert Off Ind Alert On Tone Disable Turns all tones on or off. Tones On Tones Off 37 English
E N O T O D U A I I S G N T T E S Audio/Tone Settings Feature Name Tone Tag Call Tone Tag Msg Tone Tag Escalert What it Does Settings Assigns a specic tone to all calls from a specic user
(see page 22 for details). Standard Alert #1 #7 Assigns a specic tone when receiving a specic type of radio call (see page 23 for details). Standard Alert #1 #7 Assigns a specic tone when receiving a specic message (see page 22 for details). Standard Alert #1 #7 Gradually increases the volume of the alarm tones when a call is not answered. Escalert On Escalert Off Companding
(XPand) Approximates the same audio quality for 12.5kHz channels to that of 25kHz channels. Keypad Tones Turns keypad tones on or off. Compand On Compand Off Tones On Tones Off English 38 UTILITIES You can customize some of your radios features by:
1 ) to enter Menu Mode. 2 y or z until UUUUttttiiiilllliiiittttiiiieeeessss 3 ) to select UUUUttttiiiilllliiiittttiiiieeeessss 4 y or z until you see the feature you want to change (see table below). 5 ) to select the feature. You will see the features current setting. 6 y or z for available settings. 7 ) to select the desired setting. Utilities Features What it Does Changes the power level of the radio to high or low (see page 21). Sets the time (see page 41). Sets the alarm and turns it on or off (see page 41). Feature Power Level Clock Reminder Alarm Settings Power High Power Low Set Time Display Clock Alarm On Alarm Off Set Time I I U T L T E S I 39 English Utilities Features What it Does Allows you to select the language displayed on the display. Activates/deactivates the option board installed in your radio. Displays the radios software version number. Feature Language Selection Option board Software Ver #
Settings English Spanish Portuguese French Opt Board On Opt Board Off I S E T L T U I I English 40 SETTING THE TIME To set the time:
1 ) to enter Menu Mode. 2 y or z until UUUUttttiiiilllliiiittttiiiieeeessss 3 ) to select UUUUttttiiiilllliiiittttiiiieeeessss 4 y or z until CCCClllloooocccckkkk 8 When a setting (e.g., hour) is blinking, you can change it with y or z. Hour
(AM or PM) 3:05 PM Minutes
(AM/PM or 24 hr) 9 w to proceed to the next setting (e.g., from hour to minutes). or until RRRReeeemmmmiiiinnnnddddeeeerrrr AAAAllllaaaarrrrmmmm 10 ) to save your changes. Note: You must access the clock menu to select AM/PM or 24 hr. This selection cannot be made from Reminder Alarm menu. 5 ) to conrm your selection. 6 y or z until SSSSeeeetttt TTTTiiiimmmmeeee????
7 ) to select SSSSeeeetttt TTTTiiiimmmmeeee????
11 ( to return to CCCClllloooocccckkkk or to return to or Hold down ( to exit Menu Mode. RRRReeeemmmmiiiinnnnddddeeeerrrr AAAAllllaaaarrrrmmmm I I U T L T E S I 41 English DISPLAYING THE TIME To display the time:
1 ) to enter Menu Mode. 2 y or z until UUUUttttiiiilllliiiittttiiiieeeessss 3 ) to select UUUUttttiiiilllliiiittttiiiieeeessss 4 y or z until CCCClllloooocccckkkk 5 ) to conrm your selection. 6 y or z until DDDDiiiissssppppllllaaaayyyy CCCClllloooocccckkkk????
7 ) to select DDDDiiiissssppppllllaaaayyyy CCCClllloooocccckkkk????
The radio will display the time for a preprogrammed duration. 8 ( to exit the menu. SELECTING THE DISPLAY LANGUAGE To select the display language:
1 ) to enter Menu Mode. 2 y or z until UUUUttttiiiilllliiiittttiiiieeeessss 3 ) to select UUUUttttiiiilllliiiittttiiiieeeessss 4 y or z until LLLLaaaannnngggguuuuaaaaggggeeee SSSSeeeellllcccctttt 5 ) to conrm your selection. 6 y or z until desired language is displayed. 7 ) to select desired language. 8 ( to exit the menu. I S E T L T U I I English 42 SAFETY AND WARRANTY SAFE AND EFFICIENT OPERATION OF MOTOROLA TWO-WAY RADIOS Exposure to Radio Frequency Energy National and International Standards and Guidelines Your Motorola Two-Way Radio, which generates and radiates radio frequency (RF) electromagnetic energy (EME), is designed to comply with the following National and International Standards and Guidelines regarding exposure of human beings to radio frequency electromagnetic energy:
Federal Communications Commission Report and Order No. FCC 96-326 (August 1996) American National Standards Institute
(C95.1 - 1992) National Council on Radiation Protection and Measurements (NCRP - 1986) International Commission on Non-
Ionizing Radiation Protection (ICNRP -
1986) European Committee for Electrotechnical Standardisation
(CENELEC):
ENV. 50166-
1 1995 E Human Exposure to Electromagnetic Fields Low Frequency (0Hz to 10kHz) ENV. 50166-
2 1995 E Proceedings of SC211/8 1996 Human Exposure to Electromagnetic Fields High Frequency (10kHz to 300GHz) Safety Considerations for Human Exposure to E.M.F.s from Mobile Telecommunications Equipment (M.T.E.) in the Frequency Range 30MHz - 6GHz (E.M.F. -
Electromagnetic Fields) To assure optimal radio performance and that human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards, always adhere to the following procedures:
W A R R A N T Y S A F E T Y A N D 43 English Mobile Radio Operation and EME Exposure Electromagnetic Interference/Compatibility To assure optimal radio performance and that human exposure to radio frequency electromagnetic energy is within the guidelines referenced earlier in this document, transmit only when people outside the vehicle are at least the minimum distance away from a properly installed, externally mounted antenna. Table 1 lists the minimum distance for several different ranges of radiated power. Table 1: Radiated Power and Distance Radiated Power of Vehicle-installed Mobile Two-way Radio Minimum Distance From Transmitting Antenna 7 to 15 Watts 1 Foot (30.5 cm) 16 to 50 Watts 2 Feet (61 cm) More than 50 Watts 3 Feet (91.5 cm) Note: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise congured for electromagnetic compatibility. To avoid electromagnetic interference and/or compatibility conicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. When instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions. D N A Y T E F A S Y T N A R R A W English 44 OPERATIONAL WARNINGS Vehicles with an Air Bag
W A R N I N G Do not place a radio in the area over an air bag or in the air bag deployment area. Air bags inate with great force. If a radio is placed in the air bag deployment area and the air bag inates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. Potentially Explosive Atmospheres Turn off your two-way radio when you are in any area with a potentially explosive atmosphere, unless it is a radio type especially qualied for use in such areas (for example, Factory Mutual or CENELEC approved). Sparks in a potentially explosive atmosphere can cause an explosion or re resulting in bodily injury or even death. Blasting Caps and Blasting Areas To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: Turn off two-way radio. Obey all signs and instructions. Note: The areas with potentially explosive atmospheres referred to above include fueling areas such as: below decks on boats; fuel or chemical transfer or storage facilities; areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and any other area where you would normally be advised to turn off a vehicle engine. Areas with potentially explosive atmospheres are often but not always posted. W A R R A N T Y S A F E T Y A N D 45 English The antenna must be mounted outside the building. Mount the antenna on a tower if at all possible. If the antenna is to be mounted on a building, then it must be mounted on the roof. As with all xed site antenna installations, it is the responsibility of the licensee to manage the site in accordance with applicable regulatory requirements and may require additional compliance actions such as site survey measurements, signage, and site access restrictions in order to insure that exposure limits are not exceeded. ANTENNA INSTALLATION MOBILE ANTENNAS Recommended mobile antenna installations are limited to metal body vehicles at the center of the roof and center of the trunk deck locations. The antenna installation must additionally be in accordance with:
a.The requirements of the antenna manu-
facturer/supplier. b.Instructions in the Radio Installation Manual. FIXED SITE ANTENNAS Mobile radio equipment is sometimes installed at a xed location and operated as a control station or as a xed unit. In such cases the antenna installation must comply with the following requirements in order to assure optimal performance and make sure human exposure to radio frequency electromagnetic energy is within the guidelines set forth in the above standards:
D N A Y T E F A S Y T N A R R A W English 46 LIMITED WARRANTY MOTOROLA COMMUNICATION PRODUCTS I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:
MOTOROLA INC. (MOTOROLA) warrants the MOTOROLA manufactured Communication Products listed below (Product) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:
CDM1550 Mobile Units Product Accessories Two (2) Years One (1) Year Motorola, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA. This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modications to this warranty unless made in writing and signed by an ofcer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product. MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. W A R R A N T Y S A F E T Y A N D 47 English II. GENERAL PROVISIONS:
III. STATE LAW RIGHTS:
This warranty sets forth the full extent of MOTOROLA's responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLAs option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specic legal rights, and there may be other rights which may vary from state to state. IV. HOW TO GET WARRANTY SERVICE:
You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by Motorola through one of its authorized warranty service locations. If you rst contact the company which sold you the Product
(e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call Motorola at 1-800-927-2744 US/Canada. D N A Y T E F A S Y T N A R R A W English 48 V. WHAT THIS WARRANTY DOES NOT COVER:
A Defects or damage resulting from use of the Product in other than its normal and customary manner. B Defects or damage from misuse, accident, water, or neglect. C Defects or damage from improper testing, operation, maintenance, installation, alteration, modication, or adjustment. D Breakage or damage to antennas unless caused directly by defects in material workmanship. A Product subjected to unauthorized Product modications, disassemblies or repairs
(including, without limitation, the addition to the Product of non-Motorola supplied equipment) which adversely affect performance of the Product or interfere with Motorola's normal warranty inspection and testing of the Product to verify any warranty claim. Product which has had the serial number removed or made illegible. E F G Freight costs to the repair depot. H A Product which, due to illegal or unauthorized alteration of the software/
rmware in the Product, does not function in accordance with MOTOROLAs published specications or the FCC type acceptance labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA. Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. Normal and customary wear and tear. I J VI. PATENT AND SOFTWARE PROVISIONS:
MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages nally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:
A B that MOTOROLA will be notied promptly in writing by such purchaser of any notice of such claim;
that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and W A R R A N T Y S A F E T Y A N D 49 English C should the Product or parts become, or in MOTOROLAs opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA. MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such Motorola software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modied in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modication, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights. VII.GOVERNING LAW:
This Warranty is governed by the laws of the State of Illinois, USA. D N A Y T E F A S Y T N A R R A W English 50 ACCESSORIES Motorola offers a number of accessories to enhance the productivity of your two-way radio. Many of the available accessories are listed below. For a complete list, see your Motorola dealer. AUDIO RMN4025 RMN4026 RMN4038 RSN4001 HSN8145 Compact Remote Speaker Microphone Enhanced Keypad Microphone Heavy Duty Microphone External Speaker 13W External Speaker 7.5W MOUNTING GLN7324 RLN4780 HLN8097 RLN4779 RLN4782 RKN4077 RKN4078 RKN4079 Low Prole Trunnion High Prole Trunnion Removable Slide Mount Key Lock Mount DIN Mounting Kit (in dash) Remote Mount Cable - 3 m Remote Mount Cable - 5 m Remote Mount Cable - 7 m A C C E S S O R E S I 51 English CONTROL STATION GPN6145 HPN4002 GPN6149 HPN4001 RMN4030 GLN7318 GLN7326 Desktop Power Supply 1-25W (EMC) Desktop Power Supply 1-25W Desktop Power Supply 25-45W (EMC) Desktop Power Supply 25-45W Desktop Microphone Desktop Tray without Speaker Desktop Tray with Speaker Note: A variety of interchangeable buttons are available for use in the P1-P4 locations on your radio (page 1). See your dealer for further details. I S E R O S S E C C A ANTENNAS HAD4006A HAD4007A HAD4008A HAD4009A HAD4014A HAE4002A HAE4003A HAE4010A HAE4011A HAE4019A HAE4004A HAE4012A VHF 136-144 MHz, 1/4 Wave Roof Mount VHF 146-150.8 MHz, 1/4 Wave Roof Mount VHF 150.8-162 MHz, 1/4 Wave Roof Mount VHF 162-174 MHz, 1/4 Wave Roof Mount VHF 146-172 MHz, 3.0dB Gain Roof Mount UHF 403-430 MHz, 1/4 Wave Roof Mount UHF 450-470 MHz, 1/4 Wave Roof Mount UHF 406-420 MHz, 3.5dB Gain Roof Mount UHF 450-470 MHz, 3.5dB Gain Roof Mount UHF 450-470 MHz, 5dB Gain Roof Mount UHF 470-512 MHz, 1/4 Wave Roof Mount UHF 470-494 MHz, 3.5dB Gain Roof Mount Lowband 29.7-36 MHz, 1/4 Wave Base Loaded Lowband 36-42 MHz, 1/4 Wave Base Loaded Lowband 42-50 MHz, 1/4 Wave Base Loaded 09-02105F01 BNC Connector RAB4002A RAB4003A RAB4004A 52 English Sending a Call 1. Turn radio on and select appropriate zone and channel. 2. Press PTT, hold the microphone 1 to 2 inches (2.5 to 5 cm) from your mouth, and speak clearly into it. 3. Release PTT to listen. Receiving a Call 1. Turn radio on and adjust volume to the desired level. 2. Select desired channel. 3. To respond to an incoming call, press PTT, hold the microphone 1 to 2 inches
(2.5 to 5 cm) from your mouth, and speak clearly into it. Deleting a Nuisance Channel During Scanning 1. While radio is on a nuisance channel, hold down preprogrammed Scan button until you hear a tone. 2. Release Scan button. Making a Phone Call 1. Press Phone button, or select Phone from the menu. 2. 3. Send phone number in one of the following ways:
If access code is not displayed, send access code if required. Press and release PTT to send last dialed number. or when using an enhanced keypad microphone only, press preprogrammed Speed Dial button, followed by a keypad key (18), to access rst nine numbers in your phone list. (Press PTT if buffered dial.) or when using an enhanced keypad microphone only, enter phone number using the keypad. (Press PTT if buffered dial.) 4. Press PTT, hold the microphone 1 to 2 inches (2.5 to 5 cm) from your mouth, and speak clearly into it. Ending a Phone Call 1. Send deaccess code if required. 2. Press preprogrammed Phone button, or press (. Sending and Cancelling an Emergency Alert To activate Emergency Alert., press preprogrammed Emergency button. To cancel, press and hold down Emergency button. CDM1550 Quick Reference Card Record the functions for your radios programmable buttons in the table provided below. For further information, see page 4 of this User Guide. On/Off/Volume Knob Red/Yellow/Green LED Indicators LCD Screen Channel Selector/
Menu Navigation Buttons
(Up/Down) Menu Exit/Escape Button Menu Enter/Select Button Programmable Button 3 (P3)
(Interchangeable) Microphone Jack Programmable Button 1 (P1)
(Interchangeable) Programmable Button 2 (P2)
(Interchangeable) Editing Buttons
(Left/Right) Programmable Button 4 (P4)
(Interchangeable) Button Function Short Press Long Press Hold Down Page Menu Navigation Chart
(Refer to Menu Navigation guidelines lower, left-hand corner of this page)
) y z Program Lists Phone
(p. 31) y z Radio Call
(p. 15) y z Scan List
(p. 26) Phone List
(p. 32) System Scan
(p. 25) y z on/off RadioCall List
(p. 20) edit entry add/delete entry edit priority all/delete/edit entry/edit codes Selective Call Call Alert Radio Check select/
enter ID select/
enter ID select/
enter ID Menu Navigation
) to enter Menu Mode. y or z to scroll through the list.
) to select Menu item. y or z to scroll through sub-list.
( to return to previous menu level
) to select sub-menu item. or Hold down ( to exit Menu Mode. Zone
(p. 12) Message Message Status Utilities
(p. 39) Rptr/
Talkarnd
(p. 21) Audio/
Tones
(p. 37) select/
select/
enter ID enter ID select/
enter ID y z y z y z repeater mode/
talkarnd mode Alert Vol Lvl on/off Tone Disable on/off Name Tone Tag standard/alert
#1 - #7 Message Tone/Tag standard/alert
#1 - #7 Call Tone Tag standard/alert
#1 - #7 Escalert on/off Companding on/off Keypad Tones on/off Power Level high/low/
auto Clock display/
set time Reminder Alarm on/off/
set time Language Select select Option Board on/off Light Disable on/off Software Ver #
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2008-02-04 | 29.7 ~ 36 | TNB - Licensed Non-Broadcast Station Transmitter | Class II permissive change or modification of presently authorized equipment |
2 | 2000-08-31 | 29.7 ~ 36 | TNB - Licensed Non-Broadcast Station Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2008-02-04
|
||||
1 2 |
2000-08-31
|
|||||
1 2 | Applicant's complete, legal business name |
Motorola Solutions, Inc.
|
||||
1 2 | FCC Registration Number (FRN) |
0003778479
|
||||
1 2 | Physical Address |
8000 West Sunrise Blvd
|
||||
1 2 |
Ft Lauderdale, Florida 33322
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
T******@TIMCOENGR.COM
|
||||
1 2 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
AZ4
|
||||
1 2 | Equipment Product Code |
92FT1627
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
D******** Z********
|
||||
1 2 | Title |
Regulatory Compliance Manager
|
||||
1 2 | Telephone Number |
95472********
|
||||
1 2 | Fax Number |
--********
|
||||
1 2 |
d******@motorolasolutions.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
Motorola Inc
|
||||
1 2 | Name |
M******** R******
|
||||
1 2 | Physical Address |
8000 West Sunrise Blvd
|
||||
1 2 |
Ft. Lauderdale, Florida 33322
|
|||||
1 2 |
United States
|
|||||
1 2 | Telephone Number |
954-7********
|
||||
1 2 | Fax Number |
954-7********
|
||||
1 2 |
M******@Motorola.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | TNB - Licensed Non-Broadcast Station Transmitter | ||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | MOBILE TRANSMITTER | ||||
1 2 | Mobile Transmitter | |||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 | Original Equipment | |||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | RF exposure compliance was determined in vehicle-mount antenna configurations with respect to controlled MPE limit for vehicle occupants and uncontrolled SAR limit for bystanders at an equivalent separation distance of 3 feet from a 0 dBd base-loaded quarter-wave antenna. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work related use only. Qualified end-users of this device must have the knowledge to control the exposure conditions of bystanders to ensure a minimum separation distance of 3 feet is maintained between the antenna and persons outside of the vehicle for satisfying RF exposure compliance. For other fixed-mounted operations, the antenna must be installed to provide a separation distance of at least 3 feet from persons to ensure compliance. End-users must be provide with specific instructions for meeting Occupational/Controlled Exposure Environment requirements. The highest reported SAR value at 3 feet from the antenna is 0.02 W/kg. Class 2 permissive change. | ||||
1 2 | RF exposure compliance was determined in vehicle-mount antenna configurations with respect to controlled MPE limit for vehicle occupants and uncontrolled SAR limit for bystanders at an equivalent separation distance of 3 feet from a 0 dBd base-loaded quarter-wave antenna. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work related use only. Qualified end-users of this device must have the knowledge to control the exposure conditions of bystanders to ensure a minimum separation distance of 3 feet is maintained between the antenna and persons outside of the vehicle for satisfying RF exposure compliance. For other fixed-mounted operations, the antenna must be installed to provide a separation distance of at least 3 feet from persons to ensure compliance. End-users must be provide with specific instructions for meeting Occupational/Controlled Exposure Environment requirements. The highest reported SAR value at 3 feet from the antenna is 0.02 W/kg. | |||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Motorola
|
||||
1 2 | Name |
W**** E******
|
||||
1 2 | Telephone Number |
954-7********
|
||||
1 2 | Fax Number |
954-7********
|
||||
1 2 |
F******@motorolasolutions.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 22,9 | BN | 29.7 | 36 | 72 | 5 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
1 | 2 | 22,9 | BN | 29.7 | 36 | 72 | 5 ppm | 16K0F2D | |||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 22,9 | BN | 29.7 | 36 | 72 | 5 ppm | 16K0F3E | Power is variable 55% of the | ||||||||||||||||||||||||||||||||
2 | 2 | 22,9 | 29.7 | 36 | 72 | 5 ppm | 16K0F2D | value listed |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC