FCC ID: AZ492FT7047 MULTI-BAND MOBILE 2-WAY RADIO

 

6881095C99-G.book Page 1 Tuesday, October 27, 2009 1:25 PM Product Safety and RF Energy Exposure Booklet for Mobile Two-Way Radios Installed in Vehicles or as Fixed Site Control Stations ATTENTION!

BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. The information provided in this document supersedes the general safety information contained in user guides published prior to January 2008. 2005 2009 by Motorola, Inc. All rights reserved. 10/09 1301 E. Algonquin Rd., Schaumburg, IL 60196-1078, U.S.A.

*NNTN7851B*

NNTN7851B

*6881095C99*

6881095C99-G English 6881095C99-G.book Page 2 Tuesday, October 27, 2009 1:25 PM RF Energy Exposure Awareness and Control Information, and Operational Instructions for FCC Occupational Use Requirements NOTICE: This radio is intended for use in occupational/controlled conditions, where users have full knowledge of their exposure and can exercise control over their exposure to meet FCC limits. This radio device is NOT authorized for general population, consumer, or any other use. This two-way radio uses electromagnetic energy in the radio frequency (RF) spectrum to provide communications between two or more users over a distance. It uses radio frequency (RF) energy or radio waves to send and receive calls. RF energy is one form of electromagnetic energy. Other forms include, but are not limited to, sunlight and x-rays. RF energy, however, should not be confused with these other forms of electromagnetic energy, which when used improperly, can cause biological damage. Very high levels of x-rays, for example, can damage tissues and genetic material. Experts in science, engineering, medicine, health, and industry work with organizations to develop standards for safe exposure to RF energy. These standards provide recommended levels of RF exposure for both workers and the general public. These recommended RF exposure levels include substantial margins of protection. All Motorola two-way radios are designed, manufactured, and tested to ensure they meet government-established RF exposure levels. In addition, manufacturers also recommend specific operating instructions to users of two-way radios. These instructions are important because they inform users about RF energy exposure and provide simple procedures on how to control it. English 2 6881095C99-G.book Page 3 Tuesday, October 27, 2009 1:25 PM Please refer to the following Web sites for more information on what RF energy exposure is and how to control your exposure to assure compliance with established RF exposure limits. http://www.fcc.gov/oet/rfsafety/rf-faqs.html http://www.osha.gov/SLTC/radiofrequencyradiation/index.html Federal Communication Commission Regulations The FCC rules require manufacturers to comply with the FCC RF energy exposure limits for mobile two-way radios before they can be marketed in the U.S. When two-way radios are used as a consequence of employment, the FCC requires users to be fully aware of and able to control their exposure to meet occupational requirements. Exposure awareness can be facilitated by the use of a label directing users to specific user awareness information. Your Motorola two-way radio has a RF exposure product label. Also, your Motorola user manual, or separate safety booklet, includes information and operating instructions required to control your RF exposure and to satisfy compliance requirements. Compliance with RF Exposure Standard Your Motorola two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to radio frequency electromagnetic energy. This radio complies with the IEEE and ICNIRP exposure limits for occupational/controlled RF exposure environment at duty factors of up to 50% talk-50% listen and is authorized by the FCC for occupational use. In terms of measuring RF energy for compliance with the FCC exposure guidelines, your radio antenna radiates measurable RF energy only while it is transmitting (during talking), not when it is receiving (listening) or in standby mode. 3 English 6881095C99-G.book Page 4 Tuesday, October 27, 2009 1:25 PM Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:

United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J American National Standards Institute (ANSI)/Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition Institute of Electrical and Electronic Engineers (IEEE) C95.1-2005 Edition International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 Australian Communications Authority Radiocommunications (Electromagnetic Radiation - Human Exposure) Standard, 2003 ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) additional requirements for SMR, cellular, and PCS product certification RF Exposure Compliance and Control Guidelines and Operating Instructions To control exposure to yourself and others and to ensure compliance with the RF exposure limits, always adhere to the following procedures. Guidelines:

User awareness instructions should accompany device when transferred to other users. DO NOT use this device if the operational requirements described herein are not met. English 4 6881095C99-G.book Page 5 Tuesday, October 27, 2009 1:25 PM Instructions:

Transmit no more than the rated duty factor of 50% of the time. To transmit

(talk), push the Push-To-Talk (PTT) button or, for radios equipped with VOX, speak into the microphone. The red LED will illuminate when the radio is transmitting. To receive calls, release the PTT button, or, for radios equipped with VOX, stop talking. The red LED will extinguish when the radio stops transmitting. Transmitting 50% of the time, or less, is important because this radio generates measurable RF energy exposure only when transmitting (in terms of measuring for standards compliance). Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away, as shown in Table 1, from the body of a vehicle with a properly installed antenna. This separation distance will ensure that there is sufficient distance from a properly installed

(according to installation instructions) externally-mounted antenna to satisfy the RF exposure requirements in the standards listed above. NOTE: Table 1 below lists the recommended lateral distance for people in an uncontrolled environment from the body of a vehicle with an approved, properly installed transmitting antenna (i.e., monopoles over a ground plane, or dipoles) at several different ranges of rated radio power for mobile radios installed in a vehicle. Table 1. Rated Power of Vehicle-Installed Mobile Two-Way Radio and Recommended Minimum Lateral Distance from Vehicle Body Mobile Radio Rated Power (see Note) Less than 7 watts 7 to 14 watts 15 to 39 watts 40 to 110 watts Minimum Lateral Distance from Vehicle Body 8 inches (20 centimeters) 1 foot (30 centimeters) 2 feet (60 centimeters) 3 feet (90 centimeters) 5 English 6881095C99-G.book Page 6 Tuesday, October 27, 2009 1:25 PM When a mobile radio is used in conjunction with another co-located transmitter such as a Vehicular Repeater, it is the vehicle operators responsibility to take appropriate steps to keep bystanders at the required separation distance from the vehicle to ensure compliance with the FCC's RF energy exposure limits for the general population. See the co-located transmitters user manual for more details. NOTE: If you are not sure of the rated power of your radio, contact your Motorola representative or dealer and supply the radio model number found on the radio model label. If you can not determine the rated power out, then assure 3-feet separation from the body of the vehicle. The maximum power shown on the FCC Grant may be higher than the rated power allowing for production variation. Mobile Antenna Installation Guidelines These mobile antenna installation guidelines are limited to metal body motor vehicles or vehicles with appropriate ground planes. Antennas should be installed in the center area of the roof or the trunk lid taking into account exposure conditions of backseat passengers and according to the specific instructions and restrictions in the Radio Installation Manual along with the requirements of the antenna supplier. Trunk lid installations are limited to vehicles with clearly defined flat trunk lids, and in some cases, to specific radio models and antennas. See the Radio Installation Manual for specific information on how and where to install specific types of approved antennas to facilitate recommended operating distances to all potentially exposed persons. Use only the Motorola-approved, supplied antenna or a Motorola-

approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the radio and may result in non-compliance with RF Safety Standards. English 6 6881095C99-G.book Page 7 Tuesday, October 27, 2009 1:25 PM Approved Accessories This radio has been tested and meets RF Safety Standards when used with the Motorola accessories supplied or designated for this product. Use of other accessories may result in non-compliance with RF Safety Standards. For a list of Motorola-approved antennas and accessories, refer to the user manual for your radio model. Additional Information For additional information on exposure requirements or other training information, visit http://www.motorola.com/rfhealth. Compliance and Control Guidelines and Operating Instructions for Mobile Two-Way Radios Installed as Fixed Site Control Stations If mobile radio equipment is installed at a fixed location and operated as a control station or as a fixed unit, the antenna installation must comply with the following requirements in order to ensure optimal performance and compliance with the RF energy exposure limits in the standards and guidelines listed on page 4:

The antenna should be mounted outside the building on the roof or a tower if at all possible. As with all fixed site antenna installations, it is the responsibility of the licensee to manage the site in accordance with applicable regulatory requirements and may require additional compliance actions such as site survey measurements, signage, and site access restrictions in order to ensure that exposure limits are not exceeded. For additional installation information, see the guidelines for minimum separation distances provided above in the RF Exposure Compliance and Control Guidelines and Operating Instructions section of this document. 7 English 6881095C99-G.book Page 8 Tuesday, October 27, 2009 1:25 PM Electromagnetic Interference/Compatibility NOTE: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. It may be necessary to conduct compatibility testing to determine if any electronic equipment used in or around vehicles or near fixed site antenna is sensitive to external RF energy or if any procedures need to be followed to eliminate or mitigate the potential for interaction between the radio transmitter and the equipment or device. Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Vehicles To avoid possible interaction between the radio transmitter and any vehicle electronic control modules, such as ABS, engine, or transmission controls, the radio should be installed only by an experienced installer and the following precautions should be used when installing the radio:

1. Refer to the manufacturers instructions or other technical bulletins for recommendations on radio installation. 2. Before installing the radio, determine the location of the electronic control modules and their harnesses in the vehicle. 3. Route all radio wiring, including the antenna transmission line, as far away as possible from the electronic control units and associated wiring. English 8 6881095C99-G.book Page 9 Tuesday, October 27, 2009 1:25 PM Driver Safety Check the laws and regulations on the use of radios in the area where you drive. Always obey them. When using your radio while driving, please:

Give full attention to driving and to the road. Pull off the road and park before making or answering a call if driving conditions so require. Operational Warnings W A R N I N G For Vehicles with an Air Bag DO NOT mount or place a mobile radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. Potentially Explosive Atmospheres Turn off your radio prior to entering any area with a potentially explosive atmosphere. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. The areas with potentially explosive atmospheres include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often, but not always, posted. 9 English 6881095C99-G.book Page 10 Tuesday, October 27, 2009 1:25 PM W A R N I N G Blasting Caps and Blasting Areas To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: Turn off two-way radio. Obey all signs and instructions. For radios installed in vehicles fueled by liquefied petroleum gas, refer to the (U.S.) National Fire Protection Association standard, NFPA 58, for storage, handling, and/or container information. For a copy of the LP-gas standard, NFPA 58, contact the National Fire Protection Association, One Battery Park, Quincy, MA. English 10

 

 

O5Head_6875947M01_C.book Page 1 Wednesday, October 20, 2010 12:13 PM m APX O5 Control Head Mobile Radio User Guide O5Head_6875947M01_C.book Page 2 Wednesday, October 20, 2010 12:13 PM O5Head_6875947M01_C.book Page 3 Wednesday, October 20, 2010 12:13 PM Radio On/Off Press the Power On/Off button to toggle the power on or off. Adjusting Volume Turn the Volume Knob clockwise to increase volume or counterclockwise to decrease the volume. Selecting a Zone 1 > or < to ZONE. 2 > or < button until the desired zone is displayed. 3 Press H or the PTT button to confirm the selected zone number. 4 Press the PTT button to begin transmitting on the displayed zone channel. Selecting a Channel 1 Press and hold > to scroll to CHAN and press the Menu Select button directly below CHAN. The display shows the current zone and channel. 2 Rotate the Mode knob to the desired channel. 3 Press H or the PTT button to confirm the channel. 4 Press the PTT button to transmit on the displayed zone channel. m ASTRO APX O5 Control Head Mobile Radio Quick Reference Card Product Safety and RF Exposure Compliance

+ = K J E  

Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION!

This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C99) to ensure compliance with RF energy exposure limits. Radio Controls Volume Knob Dim Button Home Button Power On/Off Button Indicators Mode Knob Orange Button _______ LED Indicators Menu Entries Menu Select Button Accessory Port (Microphone) Navigation Button 2009, 2010 by Motorola, Inc. All Rights Reserved. 10/10 1301 E. Algonquin Rd., Schaumburg, IL 60196-1078, U.S.A. Receiving and Transmitting 1 Take the microphone off hook. 2 Select zone/channel. 3 Listen for a transmission. OR Turn the Volume Knob. OR

> or < to MON then press the Menu Select button directly below MON and listen for activity. 4 Adjust volume, if necessary. 5 Press the PTT button to transmit; release to receive. Sending an Emergency Alarm 1 Press the Emergency button. A tone sounds and the display alternates EMERGENCY and the home display. 2 A dispatcher acknowledgment ACK RECEIVED display follows. AND, Trunking Only:

A high-pitched tone indicates that the alarm has been received by the trunked systems central controller. 3 Press and hold the emergency button or the PTT button to return to normal operation. To exit emergency at any time, press and hold the Emergency button.

*PMLN5592B*

PMLN5592B English O5Head_6875947M01_C.book Page 4 Wednesday, October 20, 2010 12:13 PM Sending an Emergency Call (Trunking Only) 1 Press Emergency button. 2 A tone sounds and the display alternates EMERGENCY and the home display. OR A talk prohibited tone sounds when the selected channel does not support emergency. 3 Press and hold the PTT button. Speak clearly into the microphone. 4 Release the PTT to end the transmission. To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Alarm 1 Press the preprogrammed Emergency button to activate the silent alarm feature. 2 The display does not change; the LED does not light up, and there is no tone. If silent emergency alarm is used with emergency call, pressing the PTT button exits the silent mode and initiates the emergency call. Receiving a call or data. Display Status Icons u t F V Transmitting a call or data. Received an Individual Call. The more stripes, the stronger the signal strength for the current site (trunking only). O Direct radio-to-radio communication or communication through a repeater. On = Direct Off = Repeater M K HOR . i j This channel is being monitored. Voice muting the affiliated trunking talkgroup or selected conventional channel. On = Enabled Off = Disabled L = Radio is set at Low power. H = Radio is set at High power. Scanning a scan list. Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority-

Two Channel during scan. Radio is in the view or program mode. On steady = View mode. Blinking = Program mode. Menu Navigation

< or > to Menu Entry. g directly below Menu Entry to select. H to exit. English k m l G n o The vote scan feature is enabled. On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On = AES Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On = Location feature enabled, and location signal available. Off = Location feature disabled. Blinking = Location feature enabled, but location signal unavailable. On = User is currently associated with the Off = User is currently not associated with radio. the radio. Blinking = Device registration or user registration with the server failed due to an invalid username or pin. Data activity is present.

< or > to scroll through sub-list. g directly below Menu Entry to select. O5Head_6875947M01_C.book Page i Wednesday, October 20, 2010 12:13 PM Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola, Inc. Address: Motorola, Inc. 1301 E. Algonquin Rd.Schaumburg, IL60196-1078, U.S.A. Phone Number: 1-800-927-2744 Hereby declares that the product:

Model Name: APX 7500 / APX 6500 conforms to the following regulations:

FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital Device As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. D e c l a r a t i o n o f C o n f o r m i t y i English O5Head_6875947M01_C.book Page ii Wednesday, October 20, 2010 12:13 PM Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. y t i m r o f n o C f o n o i t a r a l c e D ii English O5Head_6875947M01_C.book Page iii Wednesday, October 20, 2010 12:13 PM Contents This User Guide contains all the information you need to use the APX Mobile Radios. Declaration of Conformity . i Important Safety Information . ix Product Safety and RF Exposure Compliance . ix Software Version . ix Computer Software Copyrights . x Documentation Copyrights . x Disclaimer . x Getting Started . 1 How to Use This User Guide . 1 Notations Used in This Manual . 1 Additional Performance Enhancement . 2 Dynamic System Resilience (DSR) . 2 CrossTalk Prevention . 2 Encrypted Integrated Data (EID) . 2 SecureNet . 2 What Your Dealer/System Administrator Can Tell You . 3 Preparing Your Radio for Use . 3 Turning On the Radio . 4 Validating Compatibility During Power Up . 4 Adjusting the Volume . 5 C o n t e n t s Identifying Radio Controls . 5 Radio Parts and Controls . 6 O5 Control Head and Microphone . 6 Programmable Features . 7 Assignable Radio Functions . 7 Assignable Settings or Utility Functions . 9 Accessing the Preprogrammed Functions . 9 Using the Menu Select Buttons . 9 Using the Advance Programmable Buttons . 10 Using the Navigation Buttons . 10 Home Button . 10 Data Feature Button . 10 4-Way Navigation Button . 11 Volume Knob . 11 Mode Knob . 11 Using the Keypad . 12 iii English O5Head_6875947M01_C.book Page iv Wednesday, October 20, 2010 12:13 PM Keypad Characters Uppercase Mode . 12 Keypad Characters Lowercase Mode . 13 Keypad Characters Numeric Mode . 14 Keypad Characters Hexadecimal Mode . 15 Push-To-Talk (PTT) Button . 16 Identifying Status Indicators . 16 Status Icons . 17 Text Messaging Service (TMS) Icons . 19 Status Icons . 19 TMS Menu Options . 20 LED Indicator . 21 Intelligent Lighting Indicators . 22 Alert Tones . 23 s t n e t n o C General Radio Operation . 26 Selecting a Zone . 26 Selecting a Radio Channel . 27 Receiving and Responding to a Radio Call . 27 Receiving and Responding to a Talkgroup Call . 28 Receiving and Responding to a Private Call

(Trunking Only) . 28 Receiving and Responding to a Telephone Call . 29 Making a Radio Call . 30 iv English Making a Talkgroup Call . 30 Making a Private Call (Trunking Only) . 31 Making a Telephone Call . 32 Repeater or Direct Operation . 33 Monitoring Features . 33 Monitoring a Channel . 33 Conventional Mode Operation . 34 Advanced Features . 35 Advanced Call Features . 35 Calling a Phone Not in the List . 35 Receiving and Making a Selective Call

(Conventional Only) . 36 Receiving a Selective Call . 36 Making a Selective Call . 36 Using the Talkgroup Call Feature (Conventional Operation Only) . 37 Selecting a Talkgroup . 37 Sending a Status Call . 38 Using the Dynamic Regrouping Feature

(Trunking Only) . 38 Requesting a Reprogram . 39 Classifying Regrouped Radios . 39 Multiple Control Head Features . 40 Multiple Control Head Features . 40 Setting the Initial Control Heads ID . 40 O5Head_6875947M01_C.book Page v Wednesday, October 20, 2010 12:13 PM All Active Mode . 41 Intercom Feature in All Active Mode . 41 One Active Mode . 41 Contacts . 43 Making a Private Call from Contacts . 43 Adding a New Contact Entry . 45 Deleting a Contact Entry . 46 Adding a Contact to a Call List or Phone List . 46 Editing a Contact in a Call List or a Phone List . 47 Editing an Entry Alias . 47 Editing as Entry ID . 47 Editing a Call Type . 48 Scan Lists . 49 Viewing a Scan List . 49 Editing the Scan List . 49 Changing the Scan List Status . 50 Viewing and Changing the Priority Status . 50 Scan . 51 Turning Scan On or Off . 51 Turning Scan On While Disregarding the Squelch Code (Conventional Channels Only) . 51 Transmitting While the Scan is On . 51 Radio Programmed for Talkback Scan . 51 Radio Programmed for Non-Talkback Scan . 52 Deleting a Nuisance Channel . 52 Restoring a Nuisance Channel . 52 Changing Priorities Status While Scan is On . 53 Restoring Priorities in a Scan List . 53 Hang Up (HUB) . 53 Call Alert Paging . 54 Receiving a Call Alert Page . 54 Sending a Call Alert Page . 55 In-Call User Alert . 56 Emergency Operation . 56 Sending an Emergency Alarm . 57 Sending an Emergency Call (Trunking Only) . 57 Sending an Emergency Alarm with Emergency Call . 57 Sending a Silent Emergency Alarm . 58 Special Considerations for Emergencies . 59 Automatic Registration Service (ARS) . 60 Selecting or Changing ARS Mode . 60 Accessing the User Login Feature . 61 Logging In as a User . 61 Logging Out . 62 Text Messaging Service (TMS) . 63 Accessing TMS Feature . 63 Composing and Sending a New Text Message . 64 Sending a Quick Text Message . 65 Using the Priority Status and Request Reply Features . 67 Appending or Removing a Priority Status to a C o n t e n t s v English O5Head_6875947M01_C.book Page vi Wednesday, October 20, 2010 12:13 PM Text Message . 67 Appending or Removing a Request Reply to a Text Message . 67 Appending a Priority Status and a Reply Request to a Text Message . 67 Removing a Priority Status and a Reply Request from a Text Message . 68 Managing Text Messages . 68 Receiving a Text Message . 68 Viewing a Text Message from the Inbox . 69 Replying to a Received Text Message . 70 Accessing the Drafts Folder . 71 Managing Sent Text Messages . 71 Viewing a Sent Text Message . 71 Sending a Sent Text Message . 72 Deleting Text Messages . 73 Secure Operations . 73 Managing Encryption . 73 Loading a Single Encryption Key . 73 Loading the Group Encryption Keys . 74 Using the Multikey Feature . 74 Selecting an Encryption Key (Conventional Only) . 75 Enabling Secure Transmission . 75 Accessing the Secure Feature . 75 Selecting a Keyset . 76 Erasing the Selected Encryption Keys . 76 Requesting an Over-the-Air Rekey . 77 s t n e t n o C vi English MDC Over-the-Air Rekeying (OTAR) Page . 77 Hear Clear . 78 The Global Positioning System (GPS) . 78 Understanding the GPS Feature . 78 Enhancing GPS Performance . 79 The Outdoor Location Feature (Using GPS) . 79 Accessing the Outdoor Location Feature . 80 Saving a Waypoint . 81 Viewing a Saved Waypoint . 82 Editing the Alias of a Waypoint . 83 Editing the Coordinates of a Waypoint . 83 Deleting a Single Saved Waypoint . 84 Deleting All Saved Waypoints . 85 Measuring the Distance and Bearing from a Saved Waypoint . 85 Using the Location Feature While in Emergency Mode . 86 Trunking System Controls . 86 Using the Failsoft System . 86 Going Out-of-Range . 87 SmartZone . 87 Using Site Trunking Feature . 87 Locking and Unlocking a Site . 88 Viewing and Changing a Site . 88 Viewing the Current Site . 88 Changing the Current Site . 89 Trunked Announcement . 89 O5Head_6875947M01_C.book Page vii Wednesday, October 20, 2010 12:13 PM Initiating an Announcement . 90 Ignition Switch Options . 90 Blank . 90 Tx Inhibit . 90 PTT Tx Inhibit . 90 Required . 91 Soft Power Off . 91 Ignition Only Power Up . 91 Emergency Power Up . 91 Auto Power Off Timer . 92 Utilities . 92 Viewing Recent Calls List . 92 Selecting the Power Level . 93 Selecting a Radio Profile . 93 Controlling the Display Backlight . 94 Turning Keypad Tones On or Off . 94 Turning Voice Mute On or Off . 95 Using the Time-Out Timer . 95 Using the Conventional Squelch Operation Features . 96 Analog Options . 96 Digital Options . 96 Using the PL Defeat Feature . 97 Using the Digital PTT ID Feature . 97 Using the Smart PTT Feature (Conventional Only) 97 Accessing General Radio Information . 98 Accessing Radio Information . 98 Viewing IP Information . 99 Viewing Control Assignments . 99 Using Optional External Alarms

(Horn and Lights) . 100 Using Non-Permanent Horn and Lights . 100 Using Permanent Horn and Lights . 100 Changing the Selected Alarms . 101 Receiving a Call While Alarms are Turned On . 101 Turning Off Non-Rearmable External Alarms . 101 Turning Off Rearmable External Alarms . 102 Using the Voice Announcement . 102 C o n t e n t s Helpful Tips . 104 Accessories . 105 Appendix: Maritime Radio Use in the VHF Frequency Range . 106 Special Channel Assignments . 106 Emergency Channel . 106 Non-Commercial Call Channel . 106 Operating Frequency Requirements . 107 vii English O5Head_6875947M01_C.book Page viii Wednesday, October 20, 2010 12:13 PM Glossary . 109 Commercial Warranty and Service . 113 s t n e t n o C viii English O5Head_6875947M01_C.book Page ix Wednesday, October 20, 2010 12:13 PM Important Safety Information Product Safety and RF Exposure Compliance Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio.

+ = K J E  

ATTENTION!

This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio

(Motorola Publication part number 6881095C99) to ensure compliance with RF energy exposure limits. For a list of Motorola-approved antennas and other accessories, visit the following website:

http://www.motorola.com/governmentandenterprise Software Version All the features described in the following sections are supported by the radio's software version R05.00.00 or later. Accessing Radio Information on page 98 to determine your radio's software version. Check with your dealer or system administrator for more details of all the features supported. I m p o r t a n t S a f e t y I n f o r m a t i o n ix English O5Head_6875947M01_C.book Page x Wednesday, October 20, 2010 12:13 PM Computer Software Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. Documentation Copyrights No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others. s t h g i r y p o C e r a w t f o S r e t u p m o C x English O5Head_6875947M01_C.book Page 1 Wednesday, October 20, 2010 12:13 PM Getting Started Take a moment to review the following:

How to Use This User Guide. page 1 Notations Used in This Manual . page 1 Additional Performance Enhancement . page 2 What Your Dealer/System Administrator Can Tell You . page 3 How to Use This User Guide This User Guide covers the basic operation of the APX Mobile Radios. However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information. Notations Used in This Manual Throughout the text in this publication, you will notice the use of WARNING, Caution, and Note. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed.The following special notations identify certain items:

W A R N I N G An operational procedure, practice, or condition, etc., which may result in injury or death if not carefully observed. G e t t i n g S t a r t e d

+ = K J E  

An operational procedure, practice, or condition, etc., which may result in damage to the equipment if not carefully observed. Note:

An operational procedure, practice, or condition, etc., which is essential to emphasize. 1 English O5Head_6875947M01_C.book Page 2 Wednesday, October 20, 2010 12:13 PM Example Home button or H PHONE

Description Buttons and keys are shown in bold print or as an icon. Menu entries are shown similar to the way they appear on the radios display. This means Press the right side of the 4-way Navigation button. Additional Performance Enhancement The following are some of the latest creations designed to enhance the security, quality and efficiency of APX mobile radios. Dynamic System Resilience (DSR)

DSR ensures the radio system is seamlessly switched to a backup master site dynamically in case of system failure. DSR also provides additional indication e.g. failure detection, fault recovery, and redundancy within the system to address to the user in need. Mechanisms related to the Integrated Voice and Data (IV & D) or data centric are all supported by DSR. d e t r a t S g n i t t e G 2 English CrossTalk Prevention

This feature prevents crosstalk scenario from happening, especially when a wideband antenna is used. This feature allows the adjustment of the Trident Transmitting SSI clock rate in the radio to be varied from the Receiving Frequency. This subsequently reduced the possibilities of radio frequency interfering spurs and prevents the issues of crosstalk. Encrypted Integrated Data (EID)

EID provides security encryption and authentication of IV & D data bearer service communication between the radio and the Customer Enterprise Network. SecureNet

SecureNet allows user to perform secured communications on an Analog or Motorola Data Communication (MDC) channel. The MDC OTAR feature will allow users to perform OTAR activities on an MDC channel. O5Head_6875947M01_C.book Page 3 Wednesday, October 20, 2010 12:13 PM What Your Dealer/System Administrator Can Tell You You can consult your dealer or system administrator about the following:

Is your radio preprogrammed with any preset conventional channels?

Which buttons have been programmed to access other features?

What optional accessories may suit your needs?

Preparing Your Radio for Use Turning On the Radio. page 4 Validating Compatibility During Power Up. page 4 Adjusting the Volume . page 5 P r e p a r i n g Y o u r R a d o f o r U s e i 3 English O5Head_6875947M01_C.book Page 4 Wednesday, October 20, 2010 12:13 PM Turning On the Radio To turn off the radio, press the Power On/Off Button after the LEDs light up. Press the Power On/Off Button briefly to power on the radio. After a short time, the red, yellow and green LEDs light up. The display then shows Zone and channel text, and menu items display on the screen. The backlight will turn on to the last selected dim level. Note:

Power On/

Off Button Pressing the Power On/Off Button before the LED lights up will be ignored. If FAIL ##/## appears in the display, the radio will not function until the condition has been corrected. If ERROR ##/## appears, some non-critical data has been changed. If either of these displays appear, if the display goes blank, or if the unit appears to be locked up, see Helpful Tips on page 104 for more information. If CH MISMATCH appears, means that either the Control Head has been connected to an incompatible transceiver, or vice versa. If your radio does not power up, contact your dealer. Validating Compatibility During Power Up

The radio validates and updates the software and hardware of your control head(s) during power up. Follow the procedure below when your radio runs this task. Procedure:

1 The display shows MAINTENANCE MODE REMOTE DEVICE;

promptly followed by other maintenance statuses. 2 The display shows UPDATE DONE PLEASE RESET upon completion. OR The display shows UPDATE FAILED PLEASE RESET when it fails to update. 3 Press the Power On/Off Button to reset. The radio runs the usual power up operation if the software updates are complete. OR The radio runs the Maintenance Mode if the updates are not complete and repeat step 1. Note:

If SW INCOMPLETE appears, use Flashport Recovery Tool to update the control heads before you power on the radio again. i e s U r o f o d a R r u o Y g n i r a p e r P 4 English O5Head_6875947M01_C.book Page 5 Wednesday, October 20, 2010 12:13 PM Adjusting the Volume To increase the volume, rotate the Volume Knob clockwise. To decrease the volume, rotate the Volume Knob counterclockwise. Volume Knob Identifying Radio Controls Take a moment to review the following:

Radio Parts and Controls . page 6 O5 Control Head and Microphone . page 6 Programmable Features . page 7 Assignable Radio Functions. page 7 Assignable Settings or Utility Functions . page 9 Accessing the Preprogrammed Functions . page 9 Using the Menu Select Buttons . page 9 Using the Advance Programmable Buttons . page 10 Using the Navigation Buttons . page 10 Using the Keypad. page 12 Keypad Characters Uppercase Mode . page 12 Keypad Characters Lowercase Mode . page 13 Keypad Characters Numeric Mode . page 14 Keypad Characters Hexadecimal Mode . page 15 Push-To-Talk (PTT) Button. page 16 I i d e n t i f y n g R a d o C o n t r o s i l 5 English O5Head_6875947M01_C.book Page 6 Wednesday, October 20, 2010 12:13 PM

16 Radio Parts and Controls O5 Control Head and Microphone Volume Knob 15 Dim Button 14 Home Button 13 Power On/Off Button 12 Indicators 11 Mode Knob 10 Orange Button*

9 Push-to-Talk

(PTT) Button 8 Accy No-Dot Button (Purple)*

Data Feature Button*

Home Button

(Microphone) 17 18 Keypad Buttons 19 Navigation Button

(Microphone) Cancel Button

() Okay/Select Button () 22 21 20

*This button is programmable. Note:

The microphone is not part of a radio. It is an optional accessory. 4 Menu Entries 3 Menu Select Button*

2 Accessory Port (Microphone) 1

*These controls/buttons are programmable. Navigation Button 5 LED Indicators 7 Accy 1-Dot Button*

6 Accy 2-Dot Button*

l i s o r t n o C o d a R g n y f i t n e d i I 6 English O5Head_6875947M01_C.book Page 7 Wednesday, October 20, 2010 12:13 PM Programmable Features Any reference in this manual to a control that is preprogrammed means that the control must be programmed by a dealer or a qualified radio technician using the radios programming software, in order to assign a feature to that control. The programmable buttons can be programmed as shortcuts to radio functions or preset channels/groups depending on the duration of a button press:

Press Pressing and releasing rapidly. Long press Pressing and holding for the programmed duration (between 0.25 seconds and 3.75 seconds). Hold down Keeping the button pressed. Assignable Radio Functions

Call Alert Allows the radio to function like a pager, or to verify if a radio is active on the system. Call Response Allows you to answer a private call or phone call. Channel Selects a channel. Contacts Selects the Contacts menu. Dynamic Priority (Conventional Only) Allows any channel in a scan list (except for the Priority-One channel) to temporarily replace the Priority-Two channel. Emergency Depending on the programming, initiates or cancels an emergency alarm or call. Information Displays the basic radio information, IP-related information, and buttons or switches control mapping. Intercom Enables users of multiple control heads to talk to each other via the control heads in a multi-control head setup. Internet Protocol Address Displays the Internet Protocol (IP) address, device name, and status of the radio. Location Determines the current location (latitude, longitude, time and date), and also the distance and bearing to another location. Or, turns the GPS functionality on or off for all locations. Message Enters the current message list. Monitor (Conventional Only) Monitors a selected channel for all radio traffic until function is disabled. Multiple Private Line (Conventional Only) Selects the Multiple Private Line lists. Nuisance Delete Temporarily removes an unwanted channel, except for priority channels or the designated transmit channel, from the scan list. I i d e n t i f y n g R a d o C o n t r o s i l 7 English O5Head_6875947M01_C.book Page 8 Wednesday, October 20, 2010 12:13 PM One Touch 1 4 Launches a specific feature with one single button-press. You can setup as much as four separately programmed buttons for four different features. Phone Allows you to make and receive calls similar to standard phone calls. Private Call (Trunking Only) Allows a call from an individual radio to another individual radio. Radio Profiles Allows for easy access to a set of preprogrammed visual and audio settings of the radio. Recent Calls Allows for easy access to the list of calls recently received or made. Rekey Request Notifies the dispatcher that you require a new encryption key. Repeater Access Button (RAB) (Conventional Only) Allows to manually send a repeater access codeword. Reprogram Request (Trunking Only) Notifies the dispatcher that you want a new dynamic regrouping assignment. Request-To-Talk (Conventional Only) Notifies the dispatcher that you want to send a voice call. Scan Toggles scan on or off. Secure/Clear Toggles secure transmission on or off. Selective Call (Conventional Only) Calls an assigned radio. Site Display (Trunking Only) Views the current site or enable a site search for SmartZone operation. Site Lock/Unlock (Trunking Only) Toggles between lock and unlock mode when using the SmartZone option. Status Sends data calls to the dispatcher about a predefined status. Talkaround/Direct (Conventional Only) Toggles between using a repeater and communicating directly with another radio. Talkgroup (Conventional Only) Allows a call from an individual radio to a group of radios. Text Messaging Service (TMS) Selects the text messaging menu. TMS Quick Text Selects a predefined message. User Automatically registers with the server. Zone Down Toggles downward through the zones in the radio. Zone Select Allows selection from a list of zones. Zone Up Toggles upward through the zones in the radio. l i s o r t n o C o d a R g n y f i t n e d i I 8 English O5Head_6875947M01_C.book Page 9 Wednesday, October 20, 2010 12:13 PM Assignable Settings or Utility Functions

Dim Changes the display brightness. Front/Rear Switches one of two control heads to be active at one time. Horns/Lights Toggles horns and lights feature on or off. Low Power Toggles transmit power level between high and low. Voice Announcement Audibly indicates the current feature mode, Zone or Channel the user has just assigned. Voice Mute Toggles voice mute on or off for the channels which have enabled In-Call User Alert. When Voice Mute is active, the radio remains muted to all conventional dispatch calls and affiliated trunking group calls. Accessing the Preprogrammed Functions You can access various radio functions through one of the following ways:

A short or long press of the relevant programmable buttons. OR Use the Menu Select Button (g). Using the Menu Select Buttons

The Menu Select Buttons allow to access the menu entries of features. Note:

Check with your dealer or system administrator for the list of features activated in your radio. Your radio may be preprogrammed differently from the following example, but the steps for selecting a channel may appear as shown below:

Press the Menu Select button (g) directly below CHAN. I i d e n t i f y n g R a d o C o n t r o s i l Menu Select Button 9 English O5Head_6875947M01_C.book Page 10 Wednesday, October 20, 2010 12:13 PM Using the Advance Programmable Buttons

This feature is to help you to shorten the process of applying certain common features. Orange Button*

Menu Select Button*

Accy No-Dot Button

(Purple)*

Accy 1-Dot Button*

Accy 2-Dot Button*

Using the Navigation Buttons Home Button

The H button returns you to the home (default) display. In most cases, this is the current mode. For selected radio features, the H button is also used to save user-edited radio settings or information before returning you to the Home screen. Note:

Some features do not require you to press H to go to the Home screen. Refer to the individual feature sections in this manual for further details on saving user-edited radio settings or information. The H button also can revert to home channel. Check with your dealer or system administrator for more information. Data Feature Button

Use this button to access data-related features, such as the Text Messaging Service (TMS) feature screen.

* These programmable buttons support the One Touch Button feature.

(Quick Access) One Touch Button Enters a menu with a short press on the preprogrammed One Touch button. Features assigned to these buttons are Call, Call Alert, Phone, Repeater Access, MDC RTT Button Access, Status and Message. l i s o r t n o C o d a R g n y f i t n e d i I 10 English O5Head_6875947M01_C.book Page 11 Wednesday, October 20, 2010 12:13 PM 4-Way Navigation Button

Use this button to scroll up, down, left or right. Press and release one of the button to scroll from one entry to the next one. Press and hold one of the button to have the radio toggles through the list automatically (release the button to stop). Volume Knob

Use this Volume Knob to adjust the volume of the speakers by turning it clockwise or counterclockwise. Mode Knob

Use this Mode Knob to scroll through the channels by turning it clockwise or counterclockwise. I i d e n t i f y n g R a d o C o n t r o s i l 11 English O5Head_6875947M01_C.book Page 12 Wednesday, October 20, 2010 12:13 PM Using the Keypad You can use the 3 x 4 alphanumeric keypad on the keypad microphone to access your radios features. The keypad functions in a manner similar to a standard telephone keypad when entering numeric digits. When the keypad is used to edit a list, each key can generate different characters of the alphabet. The tables below show the number of times a key needs to be pressed to generate the required character.

Keypad Characters Uppercase Mode 14

15

16

17

18 19 20

21

) l i s o r t n o C o d a R g n y f i t n e d i I 7 Number of Times Key is Pressed 6 8

; @ _ 10

13

9

5

4

11

12

3

, C F I L O R V Y 2 Key 1 1 1

. 2 A B 3 D E 4 G H 5 J K 6 M N 7 P Q 8 T U 9 W X 0 Toggle between mixed case mode, uppercase mode, and lowercase mode.

* Space

# Toggle between numeric and letter mode. S 8 Z 12 English O5Head_6875947M01_C.book Page 13 Wednesday, October 20, 2010 12:13 PM

Keypad Characters Lowercase Mode 14

7 Number of Times Key is Pressed 6 8

; @ _ 10

13

9

5

4

11

12

3

, c f i l o r v y 2

. b e h k n q u x Key 1 1 1 2 a 3 d 4 g 5 j 6 m 7 p 8 t 9 w 0 Toggle between mixed case mode, uppercase mode, and lowercase mode.

* Space

# Toggle between numeric and letter mode. s z 15

16

17

18 19 20

21

) I i d e n t i f y n g R a d o C o n t r o s i l 13 English 15

16

17

18 19 20

21

) O5Head_6875947M01_C.book Page 14 Wednesday, October 20, 2010 12:13 PM

Keypad Characters Numeric Mode Number of Times Key is Pressed 6 8

; @ _ 10

12

13

11

9

7 14

3

, 2

. 5

4

Key 1 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 0 0

* Space

# Toggle between numeric and letter mode. l i s o r t n o C o d a R g n y f i t n e d i I 14 English O5Head_6875947M01_C.book Page 15 Wednesday, October 20, 2010 12:13 PM

Keypad Characters Hexadecimal Mode 3 2 B E A D Key 1 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 0 0

* Not applicable

# Not applicable Number of Times Key is Pressed 8 10 12 13 11 9 14 5 6 7 4 C F 15 16 17 18 19 20 21 I i d e n t i f y n g R a d o C o n t r o s i l 15 English O5Head_6875947M01_C.book Page 16 Wednesday, October 20, 2010 12:13 PM Push-To-Talk (PTT) Button PTT Button The PTT button on the side of the microphone serves two basic purposes:

While a call is in progress, the PTT button allows the radio to transmit to other radios in the call. Press and hold down PTT button to talk. Release the PTT button to listen. The microphone is activated when the PTT button is pressed. While a call is not in progress, the PTT button is used to make a new call. See Making a Radio Call on page 30 for more information. Identifying Status Indicators Your radio indicates its operational status through the following:

Status Icons . page 17 Text Messaging Service (TMS) Icons . page 19 Status Icons . page 19 TMS Menu Options . page 20 LED Indicator . page 21 Intelligent Lighting Indicators . page 22 Alert Tones. page 23 s r o t a c d n i I s u t a t S g n y f i t n e d i I 16 English O5Head_6875947M01_C.book Page 17 Wednesday, October 20, 2010 12:13 PM Status Icons The liquid crystal display (LCD) of your radio shows the radio status, text entries, and menu entries. The following are the icons that appear on the radios display. u t F V Receiving Radio is receiving a call or data. Transmitting Radio is transmitting a call or data. Call Received Radio has received an Individual Call. Received Signal Strength Indicator (RSSI) The number of bars displayed represents the received signal strength for the current site, for trunking only. The more stripes in the icon, the stronger the signal. N M K Direct On = Radio is currently configured for direct radio-to-radio communication (during conventional operation only). Off = Radio is connected with other radios through a repeater. Monitor (Carrier Squelch) Selected channel is being monitored (during conventional operation only). In-Call User Alert On = The feature is enabled. Voice muting of the affiliated trunking talkgroup or selected conventional channel is activated. Off = The feature is disabled. Voice muting of the affiliated trunking talkgroup or selected conventional channel is deactivated. I i d e n t i f y n g S t a t u s I i n d c a t o r s H or . i Power Level L = Radio is set at Low power. H = Radio is set at High power. Scan Radio is scanning a scan list. 17 English O5Head_6875947M01_C.book Page 18 Wednesday, October 20, 2010 12:13 PM j Priority Channel Scan Blinking dot = Radio detects activity on channel designated as Priority-One. Steady dot = Radio detects activity on channel designated as Priority-Two. View/Program Mode Radio is in the view or program mode. On steady = View mode Blinking = Program mode Vote Scan Enabled The vote scan feature is enabled. Secure Operation On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. AES Secure Operation On = AES Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. s r o t a c d n i I s u t a t S g n y f i t n e d i I k m l 18 English G n o

Location Signal On = Location feature is enabled, and location signal is available. Off = Location feature is disabled. Blinking = Location feature is enabled, but no location signal is available. User Login Indicator (IP Packet Data) On = User is currently associated with the radio. Off = User is currently not associated with the radio. Blinking = Device registration or user registration with the server failed due to an invalid username or pin. Data Activity Data activity is present. Hexadecimal Indicates that the text entry is currently in hexadecimal mode. O5Head_6875947M01_C.book Page 19 Wednesday, October 20, 2010 12:13 PM Text Messaging Service (TMS) Icons This feature allows you to send and receive text messages. See Text Messaging Service (TMS) on page 63 for more information. Status Icons

The following icons appear on the radios display for TMS features:

Z r Inbox Full The Inbox is full. Message Sent The text message is sent successfully. Message Unsent The text message cannot be sent. Unread Message User receives a new message. The selected text message in the Inbox has not been read.

3/6 I P

p Read Message The selected text message in the Inbox has been read. Message Index Indicates the index of the current message the user is viewing. Example: If the user is looking at the third message out of a total of 6 messages in the Inbox folder, the icon is displayed as the icon on the left column. Priority Status The Priority feature is toggled on before the message is sent. Messages in the Inbox folder are flagged with Priority. Request Reply The Request Reply feature is toggled on before the message is sent. Messages in the Inbox folder are flagged with Request Reply. I i d e n t i f y n g S t a t u s I i n d c a t o r s 19 English O5Head_6875947M01_C.book Page 20 Wednesday, October 20, 2010 12:13 PM q 2 1 3

Priority Status and Request Reply User is composing a message with a priority status and a request for a reply. Messages in the Inbox folder are flagged with Priority and Request Reply. Numeric Indicates that the text entry is currently in numeric mode. Mixed Case Indicates that the text entry is currently in normal text mode. Uppercase Indicates that the text entry is currently in uppercase mode. Lowercase Indicates that the text entry is currently in lowercase mode. s r o t a c d n i I s u t a t S g n y f i t n e d i I 20 English

TMS Menu Options Menu Option Description/Function INBX COMP DRFT SENT BACK EDIT SAVE RPLY DEL NEW LIST IMPT RQRP Brings you to your incoming messages screen. Brings you to the compose screen. Brings you to the saved message screen. Brings you to the sent messages screen. Brings you back to the previous menu screen. Edits a draft message or key in a target address. Saves the messages you have edited to the Draft folder. Replies to a message. Deletes a message or a character text during editing mode. Creates a new message. Brings you to the predefined messages screen. Toggles the Priority Status icon on or off for an outgoing message. Toggles Request Reply icon on or off for an outgoing message. O5Head_6875947M01_C.book Page 21 Wednesday, October 20, 2010 12:13 PM Menu Option Description/Function LED Indicator CURR ALL YES NO EXIT OPTN SEL SEND Deletes the current selected message. Selects to delete all the messages in the current folder. Deletes all the messages in the current folder. Cancel the delete all messages options. Exits to the Home screen. Brings you to the Options main screen. Selects a predefined message or address. Sends the message. LED indicator shows the operational status of your radio. Red LED Yellow LED Green LED Solid red Radio is transmitting. Rapidly blinking red Radio has failed the self test upon powering up or encountered a fatal error. Solid yellow Channel is busy. Blinking yellow Radio is receiving a secured transmission. Solid green Radio is powering up, or is on a non-priority channel while in the Scan List Programming mode. Blinking green Radio is receiving an individual or telephone call, or is on a Priority-Two channel while in the Scan List Programming mode. Rapidly blinking green Radio is on a Priority-One channel while in the Scan List Programming mode. I i d e n t i f y n g S t a t u s I i n d c a t o r s 21 English O5Head_6875947M01_C.book Page 22 Wednesday, October 20, 2010 12:13 PM Intelligent Lighting Indicators This feature temporary changes the radios display backlight color and the alert text background color to help signal that a radio event has occurred. Note:

This feature must be preprogrammed by a qualified radio technician. Backlight Orange Event Emergency Alerts Red Critical Alerts Green Call Alerts When The radio initiates an emergency alarm or call. The radio receives an emergency alarm or call. The radio is out of range. The radio enters failsoft mode. The radio is unable to establish a full connection with the system. The radio is unable to authenticate or register with the system. The radio receives a private call. The radio receives a phone call. The radio receives a call alert. The radio receives a selective call. s r o t a c d n i I s u t a t S g n y f i t n e d i I 22 English O5Head_6875947M01_C.book Page 23 Wednesday, October 20, 2010 12:13 PM Alert Tones An alert tone is a sound or group of sounds. Your radio uses alert tones to inform you of your radios conditions. The following table lists these tones and when they occur. You Hear Tone Name Heard Short, Low-Pitched Tone Long, Low-Pitched Tone Radio Self Test Fail Reject Time-Out Timer Warning No ACK Received Individual Call Warning Tone Time-Out Timer Timed Out When radio fails its power-up self test. When an unauthorized request is made. Four seconds before time out. When radio fails to receive an acknowledgment. When radio is in an individual call for greater than 6 seconds without any activity. When the Time-Out Timer has expired. Talk Prohibit/PTT Inhibit Out of Range Invalid Mode

(When PTT button is pressed) transmissions are not allowed.

(When PTT button is pressed) the radio is out of range of the system. When radio is on an unpreprogrammed channel. I i d e n t i f y n g S t a t u s I i n d c a t o r s A Group of Low-Pitched Tones Busy When system is busy. 23 English O5Head_6875947M01_C.book Page 24 Wednesday, October 20, 2010 12:13 PM You Hear Medium-Pitched Short, Tone Medium-Pitched Long, Tone Tone Name Valid Key-Press Radio Self Test Pass Clear Voice Priority Channel Received Heard When correct key is pressed. When radio passes its power-up self test. At beginning of a non-coded communication. When activity on a priority channel is received. Emergency Alarm Entry When entering the emergency state. Central Echo Volume Set When central controller has received a request from a radio. When volume is changed on a quiet channel. Emergency Exit When exiting the emergency state. A Group of Medium-Pitched Tones Failsoft Automatic Call Back Talk Permit Keyfail When the trunking system fails. When voice channel is available from previous request.

(When PTT button is pressed) verifying system accepting transmissions. When encryption key has been lost. When status, emergency alarm, or reprogram request ACK is received. Console Acknowledge Received Individual Call When Call Alert or Private Call is received. Call Alert Sent Site Trunking When Call Alert is received by the target radio. When a SmartZone trunking system fails. s r o t a c d n i I s u t a t S g n y f i t n e d i I 24 English O5Head_6875947M01_C.book Page 25 Wednesday, October 20, 2010 12:13 PM You Hear Ringing Low-Pitched Gurgle Unique, Chirp Unique, High-Pitched Chirp Tone Name Fast Ringing Enhanced Call Sent Phone Call Received Dynamic Regrouping Heard When system is searching for target of Private Call. When waiting for target of Private Call to answer the call. When a land-to-mobile phone call is received.

(When the PTT button is pressed) a dynamic ID has been received. New Message When a new message is received. Priority Status When a priority message is received. I i d e n t i f y n g S t a t u s I i n d c a t o r s 25 English O5Head_6875947M01_C.book Page 26 Wednesday, October 20, 2010 12:13 PM General Radio Operation Once you understand how your APX Mobile Radio is configured, you are ready to use your radio. Use this navigation guide to familiarize yourself with the basic Call features:

Selecting a Zone . page 26 Selecting a Radio Channel . page 27 Receiving and Responding to a Radio Call. page 27 Making a Radio Call . page 30 Repeater or Direct Operation . page 33 Monitoring Features . page 33 Selecting a Zone A zone is a group of channels. Note:

Your radio must be preprogrammed to allow you to use these features. Procedure:

1 > or < to ZONE. 2 Press the Menu Select button directly below ZONE. The display shows the current zone and channel. 3 > or < button until the desired zone is displayed. 4 Press H or the PTT button to confirm the selected zone number. 5 Press the PTT button to begin transmitting on the displayed zone channel. n o i t a r e p O o d a R i l a r e n e G 26 English O5Head_6875947M01_C.book Page 27 Wednesday, October 20, 2010 12:13 PM Selecting a Radio Channel Receiving and Responding to a Radio Call A channel is a group of radio characteristics, such as transmit/

receive frequency pairs. Use the following procedure to select a channel. Note:

Your radio must be preprogrammed to allow you to use this feature. If you select a channel that is not within the preprogrammed band, the radio indicates that it is on an unsupported frequency with both audio and visual warnings. Consult a qualified radio technician for the right choice between the following methods. Procedure:

Rotate the Mode knob until the display shows the desired channel. OR 1 Press and hold > to scroll to CHAN and press the Menu Select button directly below CHAN. The display shows the current zone and channel. 2 Rotate the Mode knob to the desired channel. 3 Press H or the PTT button to confirm the channel. Press the PTT button to transmit on the displayed zone channel. Once you have selected the required channel and/or zone, you can proceed to receive and respond to calls. Red LED Yellow LED Green LED You see solid red while the radio is transmitting, and solid yellow when the radio is receiving a transmission (conventional mode only). There is no LED indication when the radio receives a transmission in trunking mode. If the radio is receiving a secure transmission, the LED blinks yellow. G e n e r a l i R a d o O p e r a t i o n 27 English O5Head_6875947M01_C.book Page 28 Wednesday, October 20, 2010 12:13 PM Receiving and Responding to a Talkgroup Call

To receive a call from a group of users, your radio must be configured as part of that talkgroup. Procedure:

When you receive a talkgroup call (while on the Home screen), depending on how your radio is preprogrammed:

1 ASTRO Conventional Only:

The LED lights up solid yellow. The display shows the talkgroup alias or ID, and the caller alias or ID. OR Trunking Only:

The display shows the caller alias or ID. 2 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to respond to the call. The LED lights up solid red. 4 Release the PTT button to listen. See Making a Talkgroup Call on page 30 for details on making a Talkgroup Call.

Receiving and Responding to a Private Call

(Trunking Only) A Private Call is a call from an individual radio to another individual radio. These one-to-one calls between two radios are not heard by others in the current talkgroup. The calling radio automatically verifies that the receiving radio is active on the system and can display the caller ID. Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure:

When you receive a Private Call:

1 You hear two alert tones and the LED blinks green. The display shows CALL RECEIVED and the caller alias or ID. 2 Press the Menu Select button directly below RESP within 20 seconds after the call indicators begin. 3 During the call, the display shows the caller alias (name), if it is in the call list. OR During the call, the display shows the caller ID (number), if the callers name is not in the call list. n o i t a r e p O o d a R i l a r e n e G 28 English O5Head_6875947M01_C.book Page 29 Wednesday, October 20, 2010 12:13 PM 4 Press and hold the PTT button to talk. Release the PTT button to listen. 5 Press H to hang up and return to the Home screen. Note:

If you press PTT button before pressing the Menu Select button directly below RESP, your conversation will be heard by all members of the talk group. If 20 seconds pass before you press the Menu Select button directly below the RESP, you will not respond privately to the call just received. Instead, you initiate a Private Call. See Making a Private Call (Trunking Only) on page 31 for details on making a Private Call. Receiving and Responding to a Telephone Call

This feature allows you to receive calls similar to standard phone calls from a landline phone. Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure:

1 You hear a telephone-type ringing and the LED blinks green. The backlight of the screen turns green. The display shows PHONE CALL and the call received icon blinks. 2 Press the Menu Select button directly below RESP. 3 Press and hold the PTT button to talk. Release the PTT button to listen. 4 Press H or the Menu Select button directly below EXIT to hang up and return to the Home screen. See Making a Telephone Call on page 32 for details. G e n e r a l i R a d o O p e r a t i o n 29 English O5Head_6875947M01_C.book Page 30 Wednesday, October 20, 2010 12:13 PM Making a Radio Call You can select a zone, channel, subscriber ID, or talkgroup by using:

The preprogrammed Zone menu The Mode Knob A preprogrammed One Touch button The Contacts list (see Contacts on page 43). Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. 2 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to make the call. 4 ASTRO Conventional Only:

The LED lights up solid red. The display shows the talkgroup alias or ID. OR Trunking Only:

The LED lights up solid red. 5 Speak clearly into the microphone. 6 Release the PTT button to listen. n o i t a r e p O o d a R i l a r e n e G 30 English Making a Talkgroup Call

To make a call to a group of users, your radio must be configured as part of that talkgroup. Procedure:

1 > or < to TGRP and press the Menu Select button directly below TGRP. The display shows the last-selected talkgroup. Press the Menu Select button directly below SEL. OR Rotate the Mode Knob to select the channel with the desired talkgroup. O5Head_6875947M01_C.book Page 31 Wednesday, October 20, 2010 12:13 PM Making a Private Call (Trunking Only)

This feature allows you to send an individual Call Alert or page if there is no answer from the target radio. Your radio must be preprogrammed to allow you to use this feature. Procedure:

Press the preprogrammed Quick Access (One-Touch) Enhanced Private Call button to dial the preprogrammed ID and proceed to Step 5. OR Follow the procedure below. 1 > or < to CALL. 2 Press the Menu Select button directly below CALL. The display shows the last transmitted or received. 3 Press the Menu Select button directly below CNTS to scroll through and select the required ID. OR Press the Menu Select button directly below LIST to go to the first number of the call list. OR

> or < to the required ID. OR Use the keypad to enter the required ID. 4 Press the PTT button to start the Private Call. 5 A telephone-type ringing sounds if the receiving unit is in service. The display shows CALLING...<NUMBER> or CALLING...<ALIAS>. 6 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 7 When you are connected, the display shows the ID of the target radio. Press and hold the PTT button to talk. Release the PTT button to listen. OR If no acknowledgment is received, the display shows NO ACKNOWLEDGE. OR If the target radio does not respond before the time out, the display shows NO ANSWER. 8 Press H to return to the Home screen. See Sending a Call Alert Page on page 55 for more information. G e n e r a l i R a d o O p e r a t i o n 31 English 6 When your call is answered, press the PTT button to talk. 7 Release the PTT button to listen. 8 Press H to return to the Home screen. See Alert Tones on page 23 for more information if your call is NOT answered. O5Head_6875947M01_C.book Page 32 Wednesday, October 20, 2010 12:13 PM Making a Telephone Call

This feature allows you to make calls similar to standard phone calls to a mobile or landline phone. Procedure:

Press the preprogrammed Quick Access (One-Touch) Phone Call button to dial the preprogrammed phone number and proceed to Step 5. OR Follow the procedure below. 1 > or < to PHON. 2 Press the Menu Select button directly below PHON. The display shows the last transmitted phone number. 3 Press the Menu Select button directly below CNTS to scroll through and select the required ID. OR Press the Menu Select button directly below LIST to go to the first number of the call list. OR

> or < to the required phone number. OR Use the keypad to enter the required phone number. 4 Press and release the PTT button to dial the phone number. 5 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. n o i t a r e p O o d a R i l a r e n e G 32 English O5Head_6875947M01_C.book Page 33 Wednesday, October 20, 2010 12:13 PM Repeater or Direct Operation Monitoring Features The REPEATER operation increases the radios range by connecting with other radios through a repeater. The transmit and receive frequencies are different. The DIRECT or talkaround operation allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same. Procedure:

Press the preprogrammed Repeater/Direct switch to toggle between talkaround and repeater modes. OR Follow the procedure below. 1 > or < to DIR. 2 Press the Menu Select button directly below DIR. 3 The display shows REPEATER MODE if the radio is currently in Repeater mode. OR The display shows DIRECT MODE and the Talkaround icon if the radio is currently in Direct mode (during conventional operation only). Radio users who switch from analog to digital radios often assume that the lack of static on a digital channel is an indication that the radio is not working properly. This is not the case. Digital technology quiets the transmission by removing the noise from the signal and allowing only the clear voice or data information to be heard. Monitor a channel to ensure the channel is clear before transmitting. Monitoring a Channel

Procedure:

Lift the microphone off hook. Conventional Modes Only:

1 Listen for activity on that channel. 2 Adjust the Volume knob if necessary. 3 If you hear no activity, press and hold the PTT button to start your conversation. G e n e r a l i R a d o O p e r a t i o n You can repeat step 2 to toggle between the two modes. Once in Direct Mode, press PTT button to start conversation with the radios nearby. OR 33 English O5Head_6875947M01_C.book Page 34 Wednesday, October 20, 2010 12:13 PM Trunked Modes Only:

1 Press the PTT button. 2 If you hear two, short, high-pitched tones, or if you hear no tone and the t indicator lights steadily, then proceed with your message. 3 Release the PTT button to receive (listen). If you are not in the range of the system, you may hear a continuous low-pitched tone and the display shows OUT OF RANGE. n o i t a r e p O o d a R i l a r e n e G 34 English Conventional Mode Operation

This feature allows you to monitor channel traffic on conventional channels by defeating the coded squelch. Thus you can to listen to another user active on the channel. This way, you may be prevented from talking over someone elses conversation. Note:

This feature must first be enabled by a qualified radio technician or system administrator. Procedure:

Take the control head off hook. (This is the same as monitor on. You hear all channel traffic.) OR 1 At Home mode where the default zone and channel are being displayed, > or < button to MON. 2 Press the Menu Select button directly below MON momentarily to activate monitoring. The display shows MONITOR ON. 3 Press the Menu Select button to deactivate the monitoring. The display shows MONITOR OFF. MONITOR ON shown on the display indicates that the radio is monitoring. Pressing the Menu Select button again turns monitor off and you dont hear all channel traffic. If you try to transmit on a receive-only channel, you hear an invalid tone until you release the PTT button. O5Head_6875947M01_C.book Page 35 Wednesday, October 20, 2010 12:13 PM Advanced Features Use this navigation guide to learn more about advanced features available with your radio:

Advanced Call Features . page 35 Multiple Control Head Features. page 40 Contacts . page 43 Scan Lists . page 49 Scan . page 51 Call Alert Paging . page 54 Emergency Operation . page 56 Automatic Registration Service (ARS). page 60 Text Messaging Service (TMS) . page 63 Secure Operations. page 73 The Global Positioning System (GPS) . page 78 Trunking System Controls . page 86 Ignition Switch Options . page 90 Utilities. page 92 Advanced Call Features Calling a Phone Not in the List

1 > or < to PHON. 2 Press the Menu Select button directly below PHON. 3 Enter the desired phone number from the optional keypad microphone. The display updates as the numbers are entered. 4 Press button on the keypad microphone to make the call. 5 Press and hold the PTT button to talk. Release the PTT button to listen. 6 Press H or Menu Select button directly below PHON to exit. A d v a n c e d F e a t u r e s 35 English O5Head_6875947M01_C.book Page 36 Wednesday, October 20, 2010 12:13 PM

Receiving and Making a Selective Call

(Conventional Only) This feature allows you to receive a call from or to call a specific individual. It is intended to provide privacy and to eliminate the annoyance of having to listen to conversations that are of no interest to you. Receiving a Selective Call

Procedure:

1 When you receive a Selective Call, you hear two alert tones and the LED lights up solid yellow. The call received icons blink and the display alternates between CALL RECEIVED and the home display. 2 The speaker unmutes. 3 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 4 Press and hold the PTT button to talk. Release the PTT button to listen. Note:

If you press PTT button before pressing the Menu Select button directly below CALL, your conversation will be heard by all members of the talk group. s e r u t a e F d e c n a v d A 36 English If 20 seconds pass before you press the Menu Select button directly below the CALL, you will not respond privately to the call just received. Instead, you initiate a Selective Call. See Making a Selective Call on page 36. Making a Selective Call

Procedure:

Press the preprogrammed Quick Access (One-Touch) Selective Call button to dial the preprogrammed ID and proceed to Step 4. OR Follow the procedure below. 1 > or < to CALL. 2 Press the Menu Select button directly below CALL. The display shows the last transmitted or received ID. 3 Press the Menu Select button directly below CNTS to scroll through and select the required ID. OR Press the Menu Select button directly below LIST to go to the last number dialed. OR

> or < to the required ID. OR Use the keypad to enter the required ID. O5Head_6875947M01_C.book Page 37 Wednesday, October 20, 2010 12:13 PM 4 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 5 Press and hold the PTT button to start the Selective Call. The display shows the ID of the target radio. 6 Release the PTT button to listen. 7 Press H to return to the Home screen. If you do not press H button to hang up, your radio will remain in Selective Call state with the other unit. You will miss all subfleet traffic and incoming phone calls.

Using the Talkgroup Call Feature (Conventional Operation Only) This feature allows you to define a group of conventional system users so that they can share the use of a conventional channel. Note:

Encryption keys are associated to talkgroups. When talkgroups are enabled, encryption keys are changed by changing the active talkgroup. See Secure Operations on page 73 for more information. 2 Press the Menu Select button directly below TGRP. The display shows the last talkgroup that was selected and stored. 3 > or < to PSET for the preset preprogrammed talkgroup. OR

> or < to the required talkgroup. OR Use the keypad to enter the number of the corresponding talkgroup in the list. 4 Press the Menu Select button directly below SEL to save the currently selected talkgroup and return to the Home screen. 5 If the encryption key associated to the new talkgroup is erased, a momentary key fail tone sounds and the display shows KEY FAIL. OR If the encryption key that is associated to the new talkgroup is not allowed, a momentary key fail tone sounds and the display shows ILLEGAL KEY. 6 Press H or the PTT button to exit. A d v a n c e d F e a t u r e s Selecting a Talkgroup

Procedure:

1 > or < to TGRP. 37 English O5Head_6875947M01_C.book Page 38 Wednesday, October 20, 2010 12:13 PM Sending a Status Call

This feature allows you to send data calls to the dispatcher about a predefined status. Each status can have up to a 14-character name. A maximum of eight status conditions is possible. Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure:

Press the preprogrammed Status button and proceed to Step 3. OR Follow the procedure below. 1 > or < to STS. 2 Press the Menu Select button directly below STS. 3 The display shows the last acknowledged status call, or the first status in the list. 4 > or < to the required status. OR Use the keypad to enter a number corresponding to the location in the status list. 5 Press the PTT button to send the status. The display shows PLEASE WAIT. s e r u t a e F d e c n a v d A 38 English 6 When the dispatcher acknowledges, four tones sound and the display shows ACK RECEIVED. The radio returns to normal dispatch operation. OR If no acknowledgment is received, a low-pitched tone sounds and the display shows NO ACKNOWLEDGE. 7 Press H to return to the Home screen. No traffic is heard on trunked channels while Status Calls is selected. If the radio detects no Status Call activity for six seconds, an alert tone sounds until you press H or the PTT button.

Using the Dynamic Regrouping Feature (Trunking Only) This feature allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. This feature is typically used during special operations and is enabled by a qualified radio technician. You will not notice whether your radio has this feature enabled until a dynamic regrouping command is sent by the dispatcher. Note:

If you try to access a zone or channel that has been reserved by the dispatcher as a dynamically regrouped mode for other users, an invalid tone sounds. O5Head_6875947M01_C.book Page 39 Wednesday, October 20, 2010 12:13 PM Procedure:

1 When your radio is dynamically regrouped, it automatically switches to the dynamically regrouped channel. A gurgle tone sounds and the display shows the dynamically regrouped channels name. 2 Press the PTT button to talk. Release PTT button to listen. When the dispatcher cancels dynamic regrouping, the radio automatically returns to the zone and channel that you were using before the radio was dynamically regrouped. Requesting a Reprogram

This feature lets you notify the dispatcher that you want a new dynamic regrouping assignment. Procedure:

Press the preprogrammed Reprogram Request button to send reprogram request to the dispatcher and proceed to Step 3. OR Follow the procedure below. 1 > or < to RPGM. 2 Press the Menu Select button directly below RPGM to send reprogram request to the dispatcher. the radio returns to the Home screen. OR If the dispatcher does not acknowledge the reprogram request within six seconds, a low-pitched alert tone sounds and the display shows NO ACKNOWLEDGE. Try again or press H to cancel and return to the Home screen. Classifying Regrouped Radios

The dispatcher can classify regrouped radios into either of two categories: Select Enabled or Select Disabled. Select-enabled radios are free to change to any available channel, including the dynamic-regrouping channel, once the user has selected the dynamic-regrouping position. Select-disabled radios cannot change channels while dynamically regrouped. The dispatcher has forced the radio to remain on the dynamic-regrouping channel. The Scan or Private Call feature cannot be selected while your radio is Select Disabled. A d v a n c e d F e a t u r e s 3 The display shows REPROGRAM RQST and PLEASE WAIT. 4 If you hear five beeps, the dispatcher has acknowledged the reprogram request. The display shows ACK RECEIVED and 39 English O5Head_6875947M01_C.book Page 40 Wednesday, October 20, 2010 12:13 PM Multiple Control Head Features Multiple Control Head Features

This feature allows a transceiver to control as many as four O5 control heads on APX 7500 and, up to two O5 control heads on APX 6500. You can use the CAN cables to connect in any configuration that does not exceed 131 feet (40 meters) in combined length. Refer the O5 Control Head Installation Manual (HLN6947) for further information. The Multiple Control Head (MCH) feature consists of 2 modes that can be programmed via Customer Programming Software

(CPS):

All Active mode One Active mode Note:

If two or more control heads are connected to the system before enabling the MCH feature in the CPS, the radio will display EXTRA CH or CH ID # ERR. Both errors are FATAL. s e r u t a e F d e c n a v d A 40 English Setting the Initial Control Heads ID

This feature allows you to setup the control head in the Front Panel Programming (FPP) mode. During the setup, the control heads are defined as Control Head Number 1, Control Head Number 2, Control Head Number 3 and Control Head Number 4. Procedure:

1 Press the Power button to power off the radio. 2 Press and hold the left-most Menu Select button and the emergency button simultaneously. 3 While continuing to depress these two buttons, press the Power button to power on the radio and the control head. 4 The radio and the control head will power on into FPP mode. The display shows control heads ID number. 5 Turn the Mode knob to change the control heads ID number. 6 Press the Power button to power off the radio and exit FPP mode. 7 Repeat steps 1 to 5 above to set the ID number for the rest of the attached control heads. O5Head_6875947M01_C.book Page 41 Wednesday, October 20, 2010 12:13 PM All Active Mode

The All Active mode enables all connected control heads attached to the radio to operate concurrently with each other. When you activate a feature on one control head, the rest of the control heads will have the same activated features and indicators on their respective display. Note:

The multiple control head feature allows only control heads of the same type to be connected. Upon power up, if a control head of a different type is connected to the radio, the radio reports the FATAL error CH MISMATCH on the display of all attached control heads. Intercom Feature in All Active Mode

The intercom feature allows one control head user to talk to another control head user in a Multiple Control Head configuration. At any given time, when a control head being operated has priority for the intercom call, all other control heads are blocked until the active control head releases PTT button. This can be made on any attached control head. This feature only applies to control heads in the All Active mode. Procedure:

1 Press the Menu Select button directly below INTC to activate the intercom feature of any of the control heads. 2 Press the PTT button to initiate an intercom transmission. All control heads that are attached will receive the same intercom call. 3 The display of the control heads receiving the intercom call shows the alias/ID number of the transmitting control head. 4 Press the Menu Select button directly below EXIT to deactivate the intercom feature. OR Press H to deactivate the intercom feature. The intercom feature also deactivates when user initiates a mode change. If the radio is on an emergency channel, pressing of the EMERGENCY button or the emergency footswitch button on any control head also deactivates the intercom feature. A d v a n c e d F e a t u r e s One Active Mode

The One Active mode enables only one control head to be visibly active at a time in a two control head system. Note:

In the One Active mode, if more than two control heads are present upon power up, the radio shows a FATAL error EXTRA CH on the display of all attached control heads. The active control head commands the system normally while the inactive control head is in remote mode with its display shows REMOTE. 41 English O5Head_6875947M01_C.book Page 42 Wednesday, October 20, 2010 12:13 PM The Volume knob, DIM button, Front/Rear (F/R) softkey and Emergency button remain active on the inactive control head, while all other controls are disabled. Emergency footswitch and VIP inputs remain active on the inactive control head. The VIP input control head is configurable in the CPS and VIP should be attached to the control head selected in the CPS. Note: Only two (2) control heads are supported in the one active mode. Transceiver Follow the procedure below to change the command between the two control heads. Procedure:

Press the Menu Select button directly below F/R. OR Press the Menu Select button preprogrammed user button on the keypad microphone. Z1 ZONE CHAN PWR SQL Active Radio REMOTE F/R Non-Active Radio s e r u t a e F d e c n a v d A 42 English O5Head_6875947M01_C.book Page 43 Wednesday, October 20, 2010 12:13 PM Contacts This feature provides address-book capabilities on your radio. Each entry corresponds to an alias (name) or ID (number) that you use to initiate a call. Contact entries are alphabetically sorted according to entry alias. Each alias can have up to 5 IDs of different call types associated with it. Additionally, each entry, depending on context (conventional, trunking, or phone), associates with one or more of the four types of calls: Phone Call, Selective Call, Private Call, or Call Alert. Each entry within Contacts displays the following information:

Call Alias (Name) Call ID (Number) Call Type (Icon) WACN ID (Astro 25 Trunking IDs only) System ID Note:

Your radio must be preprogrammed to allow you to add, edit, or delete the contact entries. Your radio also supports a maximum of 50 call lists. Each list can store up to 100 IDs (numbers). A d v a n c e d F e a t u r e s Note:

Your radio is preprogrammed with a number of contacts per Call Lists. Check with your dealer or system administrator for more information. If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Making a Private Call from Contacts

Note:

Your radio must be preprogrammed to allow you to use this feature. Procedure:

Use the Options Menu. 1 > or < to CNTS. 2 Press the Menu Select button directly below CNTS to the call list. The display shows Contact Alias. 3 > or < to the required subscriber alias. 4 Press the Menu Select button directly below OPTN. 5 > or < to CALL and press the Menu Select button directly below SEL. 6 > or < to select the call type. 43 English 6 Press the PTT button to initiate the call. During the call, the display shows the subscriber alias. 7 Press and hold the PTT button to talk. The LED lights up solid red. OR Release the PTT button to listen. The LED lights up solid yellow. 8 If there is no voice activity for a preprogrammed period of time, the call ends. OR The call ends when it reaches the maximum ring time. O5Head_6875947M01_C.book Page 44 Wednesday, October 20, 2010 12:13 PM 7 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 8 Press the PTT button to initiate the call. During the call, the display shows the subscriber alias. 9 Press and hold the PTT button to talk. The LED lights up solid red. OR Release the PTT button to listen. The LED lights up solid green. 10 If there is no voice activity for a programmed period of time, the call ends. OR The call ends when it reaches the maximum ring time. OR Use the PTT button:

1 > or < to CNTS. 2 Press the Menu Select button directly below CNTS. 3 > or < to the required subscriber alias. 4 Press the Menu Select button directly below CNTS. The display shows Contact Alias. 5 Hold the microphone vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. s e r u t a e F d e c n a v d A 44 English O5Head_6875947M01_C.book Page 45 Wednesday, October 20, 2010 12:13 PM Adding a New Contact Entry

Procedure:

1 > or < to CNTS. 2 Press the Menu Select button directly below CNTS. The entries are alphabetically sorted. 3 > or < to {NEW CONTACT} and press the Menu Select button directly below SEL. 4 The display shows NAME. Press the Menu Select button directly below EDIT. Use the keypad to enter the name. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below DEL to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 5 Press the Menu Select button directly below OK once you have entered the name. OR Press the Menu Select button directly below CNCL to return to the previous screen. A d v a n c e d F e a t u r e s 6 > or < to {ADD NUMBER} and press the Menu Select button directly below SEL. The display shows TYPE 1 <DEFAULT TYPE>. 7 Press Menu Select button directly below EDIT. 8 > or < to the required channel and press the Menu Select button directly below OK. 9 > or < to NUMBER 1 and press the Menu Select button directly below EDIT. The display shows NUMBER 1 and a cursor appears. Use the keypad to enter the number. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below DEL to delete any unwanted characters. 10 Press the Menu Select button directly below OK once you have entered the number. OR Press the Menu Select button directly below CNCL to return to the previous screen. 11 Press the Menu Select button directly below DONE once you have finished. 12 The display shows <ENTRY> STORED, confirming that the contact entry has been added. 13 The radio returns to the main Contacts screen. 45 English O5Head_6875947M01_C.book Page 46 Wednesday, October 20, 2010 12:13 PM Deleting a Contact Entry

Procedure:

1 > or < to CNTS. 2 Press the Menu Select button directly below CNTS. The entries are alphabetically sorted. Adding a Contact to a Call List or Phone List

Procedure:

1 > or < to CNTS. 2 Press the Menu Select button directly below CNTS. The entries are alphabetically sorted. 3 > or < to the entry you want to delete and press the Menu Select button directly below OPTN. 3 > or < to the entry you want to add to the call list and press the Menu Select button directly below OPTN. 4 > or < to DELETE and press the Menu Select button directly below SEL. The display shows <ENTRY> CONFIRM DEL?. 4 > or < to ADD TO CALLLST or ADD TO PHONLST and press the Menu Select button directly below SEL. 5 Select YES to delete the entry. The display shows <ENTRY> DELETED and the radio returns to the main screen for Contacts. OR Select NO to return to the main screen for Contacts. 5 > or < until the display shows {AVAILABLE} and press the Menu Select button directly below ADD to add as a new entry. OR

> or < until the display shows <ENTRY> and its associated number and press the Menu Select button directly below RPLC to replace the existing entry. 6 The display shows <ENTRY> ADDED, confirming the addition of the contact to the list. 7 The radio returns to the main display for Contacts. s e r u t a e F d e c n a v d A 46 English O5Head_6875947M01_C.book Page 47 Wednesday, October 20, 2010 12:13 PM

Editing a Contact in a Call List or a Phone List Editing an Entry Alias

Procedure:

1 > or < to CNTS. 2 Press the Menu Select button directly below CNTS. The entries are alphabetically sorted. 3 > or < to the entry you want to edit and press the Menu Select button directly below OPTN. 4 > or < to EDIT and press the Menu Select button directly below SEL. 5 > or < to the entry alias you wish to change and press the Menu Select button directly below EDIT. 6 A cursor appears. Use the keypad to edit the name. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below DEL to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 7 Press the Menu Select button directly below OK once you have finished. The display returns to the Edit Contact screen. 8 Press the Menu Select button directly below DONE to save your changes and return to the main screen for Contacts. Editing as Entry ID

Procedure:

1 > or < to CNTS. 2 Press the Menu Select button directly below CNTS. The entries are alphabetically sorted. 3 > or < to the entry you want to edit and press the Menu Select button directly below OPTN. 4 > or < to EDIT and press the Menu Select button directly below SEL. 5 > or < to the entry ID you wish to change and press the Menu Select button directly below EDIT. A d v a n c e d F e a t u r e s 6 A cursor appears. Use the keypad to edit the number. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below DEL to delete any unwanted characters. 47 English O5Head_6875947M01_C.book Page 48 Wednesday, October 20, 2010 12:13 PM Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 7 Press the Menu Select button directly below OK once you have finished. The display returns to the Edit Contact screen. 8 Press the Menu Select button directly below DONE to save your changes and return to the main screen for Contacts. s e r u t a e F d e c n a v d A 48 English Editing a Call Type

Procedure:

1 > or < to CNTS. 2 Press the Menu Select button directly below CNTS. The entries are alphabetically sorted. 3 > or < to the entry you want to edit and press the Menu Select button directly below OPTN. 4 > or < to EDIT and press the Menu Select button directly below SEL. 5 > or < to TYPE and press the Menu Select button directly below EDIT. 6 > or < to choose from the list of call types given and press the Menu Select button directly below OK to select. 7 The display returns to the Edit Contact screen. 8 Press the Menu Select button directly below DONE to save your changes and return to the main screen for Contacts. O5Head_6875947M01_C.book Page 49 Wednesday, October 20, 2010 12:13 PM Scan Lists Scan lists are created and assigned to individual channels/

groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group. Your radio supports different types of Scan Lists:

Trunking Priority Monitor Scan List Conventional Scan List Talkgroup Scan List A maximum of 200 Scan Lists can be programmed in your radio. These lists must be preprogrammed by a qualified radio technician. Viewing a Scan List

Procedure:

1 > or < to SCNL. 2 Press the Menu Select button directly below SCNL. 3 > or < to view the members on the list. 4 Press the H to exit the current display and return to the Home screen. A d v a n c e d F e a t u r e s Editing the Scan List

This feature lets you change scan list members and priorities. Procedure:

1 > or < to SCNL. 2 Press the Menu Select button directly below SCNL. The display shows the lists that can be changed. 3 > or < to the entry you want to edit. 4 Press the Menu Select button directly below SEL to add and/or change the priority of the currently displayed channel in the scan list. OR Press the Menu Select button directly below DEL to delete the currently displayed channel from the scan list. OR Press the Menu Select button directly below RCL to view the next member of the scan list. 5 > or < to select more channels to be added or deleted. OR Use the keypad to go directly to additional channels to be added or deleted. OR Use the Mode Knob to select additional channels to be added or deleted. 49 English O5Head_6875947M01_C.book Page 50 Wednesday, October 20, 2010 12:13 PM 6 Press H to exit scan list programming and return to the Home screen. 5 Press H to exit scan list programming and return to the Home screen. See Viewing and Changing the Priority Status on page 50 for more information on how to add and/or change the priority of the currently displayed channel in the scan list. Changing the Scan List Status

Procedure:

1 Long press the preprogrammed Scan side button. 2 > or < to the member you want to edit. 3 Press the button or press the Menu Select button directly below SEL once to add the currently displayed channel to the scan list. OR Press the button or press the Menu Select button directly below SEL, one or more times to change the scan list status icon of the currently displayed channel. 4 > or < to select more list members whose scan status you want to change. OR Use the keypad to go directly to that scan list member. OR Use the Mode Knob to select another scan list member. s e r u t a e F d e c n a v d A 50 English Viewing and Changing the Priority Status

Procedure:

1 Below the SEL, DEL, and RCL screen, press the Menu Select button directly below SEL to view and/or change the priority status of the currently displayed channel. OR Below the SEL, DEL, and RCL screen, press the button or press the Menu Select button directly below SEL, one or more times to view and/or change the scan list status icon of the currently displayed channel. 2 A Scan icon indicates that the current channel is in the scan list as a non-priority channel. The LED lights up solid green. OR A Priority-Two Channel Scan icon indicates that the current channel is in the scan list as the Priority-Two channel. The LED blinks green. OR A Priority-One Channel Scan icon indicates that the current channel is in the scan list as the Priority-One channel. The LED rapidly blinks green. You hear all traffic on the Priority-

One channel, regardless of traffic on non-priority channels. OR No icon indicates that the current channel is deleted from the scan list. O5Head_6875947M01_C.book Page 51 Wednesday, October 20, 2010 12:13 PM Scan This feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels. Turning Scan On or Off

Procedure:

Press the preprogrammed Scan button. OR Follow the procedure below. 1 > or < to SCAN. 2 Press the Menu Select button directly below SCAN. 3 The display shows SCAN OFF if scan is disabled. Press the Menu Select button directly below SCAN to enable scan. OR The display shows SCAN ON and the scan status icon if scan is enabled. Press the Menu Select button directly below SCAN to disable scan. 4 The radio returns to the Home screen.

Turning Scan On While Disregarding the Squelch Code (Conventional Channels Only) Procedure:

1 > or < to MON. 2 Press the Menu Select button directly below MON. 3 The brief MONITOR ON display indicates that the radio is disregarding the squelch code. While scanning for activity, you can still receive fleetwide, system-wide, dynamic regrouping, incoming telephone interconnect and Private Conversation/Call Alert calls. Respond to these types of calls as you would normally on the selected channel. However, when scanning different channels while in talkgroup scan, incoming Private Conversation/Call Alert calls may be missed.

Transmitting While the Scan is On A d v a n c e d F e a t u r e s Radio Programmed for Talkback Scan

Procedure:

1 Press the PTT button to transmit on the channel indicated by the display. 51 English O5Head_6875947M01_C.book Page 52 Wednesday, October 20, 2010 12:13 PM The radio does not begin scanning again for a predetermined hang time after you release the PTT button, allowing the other party to respond. If the other party responds within the hang time, scanning does not resume until the full hang time expires after they have finished speaking, allowing the conversation to be completed. To transmit on the selected channel if another channel is active, first turn scan off by pressing the Menu Select button below SCAN momentarily. Radio Programmed for Non-Talkback Scan

Procedure:

1 Press the PTT button at any time to transmit on the selected channel or fixed channel. To make a Call Alert page, or Private Conversation call while scanning, press either the Menu Select button directly below PAGE or CALL. The call is entered on the selected channel and scanning is halted until the call is exited by pressing H or pressing the Menu Select button below either PAGE or CALL. s e r u t a e F d e c n a v d A 52 English Deleting a Nuisance Channel

If a channel continually generates unwanted calls or noise

(termed a nuisance channel), you can temporarily remove the unwanted channel from the scan list. This capability does not apply to priority channels or the designated transmit channel. Procedure:

1 When the radio is locked onto the channel to be deleted,

> or < to NUIS. 2 Press the Menu Select button directly below NUIS. Restoring a Nuisance Channel

Procedure:

To restore the deleted nuisance channel, do one of the following:

Turn scan off, then on. OR Change modes. OR Turn off the radio, and then turn it back on. Nuisance mode delete can be disabled by the system administrator. O5Head_6875947M01_C.book Page 53 Wednesday, October 20, 2010 12:13 PM Changing Priorities Status While Scan is On

While the radio is scanning, the dynamic priority change feature allows you to temporarily change any channel in a scan list

(except for the Priority-One channel) to the Priority-Two channel. This change remains in effect until scan is turned off. Scan then reverts to the preprogrammed (original) setting. Procedure:

1 Press the Menu Select button directly below DYNP to change the priority of a non-priority channel in the scan list to Priority-Two. 2 Press H momentarily to exit the scan list and resume scanning. A d v a n c e d F e a t u r e s Restoring Priorities in a Scan List

Procedure:

To restore the original channel priorities in a scan list, do one of the following:

Turn scan off, then on. Change channels. OR OR Turn off the radio, and then turn it back on. Hang Up (HUB)

To temporarily suspend Scan Mode operation, remove the control head from the Hang Up Box (HUB). You are allowed to use the control head while scan is suspended. However, Priority Member scanning is not suspended. This feature applies to all Scan Lists and Scan Types. Scan is resumed once the control head is returned to the holding clip and the preprogrammed hang time has elapsed. Note:

Priority Scan List members are continuously scanned only when the Scan List, Designated Tx Member field is set to Talkback in the radio programming. Otherwise, all scan mode operation is suspended. 53 English Receiving a Call Alert Page

Procedure:

When you receive a Call Alert page 1 You hear four repeating alert tone and the green LED blinks. OR You hear one alert tone and the green LED blinks if Call Alert Tone Auto Reset is enabled. 2 The call received icons blinks and the display shows PAGE RECEIVED. 3 Press the PTT button to answer. OR Press any button to clear the Call Alert page. See Making a Talkgroup Call on page 30 or Making a Private Call (Trunking Only) on page 31 for more information. O5Head_6875947M01_C.book Page 54 Wednesday, October 20, 2010 12:13 PM Call Alert Paging This feature allows your radio to work like a pager. Even if other users are away from their radios, or if they are unable to hear their radios, you can send them an individual Call Alert page. You can also verify if a radio is active on the system. Depending on how your radio is programmed, when you make an Enhanced Private Call, the radio either automatically sends a Call Alert page if there is no answer after the maximum ring time, OR when you press the PTT button. Note:

This feature must be preprogrammed by a qualified radio technician. s e r u t a e F d e c n a v d A 54 English O5Head_6875947M01_C.book Page 55 Wednesday, October 20, 2010 12:13 PM Sending a Call Alert Page

Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure:

Press the preprogrammed Quick Access (One-Touch) Call Alert Paging button to send a page to the preprogrammed ID and proceed to Step 5 of the procedure below. OR Follow the procedure below. 1 > or < to PAGE. 2 Press the Menu Select button directly below PAGE. 3 > or < to select the required ID. 4 Press the PTT button to send the page. 5 The display shows PAGING...<NUMBER> or <ALIAS>. 6 If the call alert page is sent successfully, four highpitch tone sounds and the display shows ACK RECEIVED. OR If the call alert page is not acknowledged, a low tone sounds and the display shows NO ACKNOWLEDGE. 7 The radio returns to the Home screen. OR A d v a n c e d F e a t u r e s Press the Menu Select button directly below OK to return to the main screen for Contacts. OR Follow the procedure below. 1 > or < to CALL. 2 Press the Menu Select button directly below CALL. 3 > or < to select the required ID, press the PTT button to initiate the call. 4 If the target radio does not respond after a preprogrammed period of time, the display shows SEND PAGE?. 5 Press the Menu Select button directly below YES to send the call alert page. OR Press the Menu Select button directly below NO to exit the screen without sending the call alert page. 6 The display shows PAGING...<ALIAS>. 7 If the call alert page is sent successfully, a tone sounds and the display shows ACK RECEIVED. OR If the call alert page is not acknowledged, a low tone sounds and the display shows NO ACKNOWLEDGE. 8 The radio returns to the Home screen. OR 55 English O5Head_6875947M01_C.book Page 56 Wednesday, October 20, 2010 12:13 PM Press the Menu Select button directly below OK to return to the main screen for Contacts. Emergency Operation In-Call User Alert

You can enable and disable voice transmission, if needed. Procedure:

1 Make sure you are in Home mode where the default zone and mode are being displayed. 2 > or < to scroll to the VMUT. 3 Press the Menu Select button directly below VMUT. 4 Press the Menu Select button directly below VMUT or the VMut preprogrammed button again to turn the feature off and you will be able to hear to normal dispatch calls. Pressing the Menu Select button directly below VMUT or the VMut programmed button momentarily toggles between Voice mute on and Voice mute off. VOICE MUTE ON shown on the display indicates that the radio is muted to all conventional dispatch calls and affiliated trunking group calls. s e r u t a e F d e c n a v d A 56 English The Emergency feature is used to indicate a critical situation. If the Orange button is preprogrammed to send an emergency signal, this signal overrides any other communication over the selected channel. Your radio supports 5 Emergency modes:

Emergency Call Emergency Alarm Emergency Alarm with Call Silent Emergency Alarm Special Considerations for Emergencies Check with your dealer or system administrator for more information on the programming of this feature. Only one of the Emergency modes above can be assigned to the preprogrammed Emergency button or the Emergency footswitch. Note:

To exit emergency at any time, press and hold the preprogrammed Emergency button for about a second. O5Head_6875947M01_C.book Page 57 Wednesday, October 20, 2010 12:13 PM Sending an Emergency Alarm

This feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher. Procedure:

1 Press the preprogrammed Emergency button. A tone sounds and the display alternates EMERGENCY and the home display. 2 A dispatcher acknowledgment ACK RECEIVED display follows. AND, Trunking Only:

A high-pitched tone indicates that the alarm has been received by the trunked systems central controller. 3 Press and hold the emergency button or the PTT button to return to normal operation. Sending an Emergency Call (Trunking Only)

Procedure:

1 Press preprogrammed Emergency button. 2 A tone sounds and the display alternates EMERGENCY and the home display. OR A short low-pitched tone sounds when the selected channel does not support emergency. 3 Hold the microphone vertically 1 to 2 inches (2.0 to 2.5 cm) from your mouth. 4 Press and hold the PTT button. Speak clearly into the microphone. 5 Release the PTT to end the transmission. 6 Press and hold the preprogrammed Emergency button until a tone sounds to exit Emergency mode.

Sending an Emergency Alarm with Emergency Call A d v a n c e d F e a t u r e s This feature allows you to send an Emergency Alarm to another radio. Upon acknowledgement, both radios can communicate over a preprogrammed Emergency channel. If the radio has both emergency call and alarm features enabled, it automatically proceeds to the call mode after the alarm is acknowledged. 57 English O5Head_6875947M01_C.book Page 58 Wednesday, October 20, 2010 12:13 PM Procedure:

1 Press the preprogrammed Emergency button to activate the emergency call/alarm feature. 2 The display alternates EMERGENCY and the home display. 3 A high-pitched tone sounds, indicating that the alarm has been received by the trunked systems central controller. A dispatcher acknowledgment (four high-pitched tones) follows, accompanied by an ACK RECEIVED display. 4 Hold the microphone vertically 1 to 2 inches (2.0 to 2.5 cm) from your mouth. 5 Press and hold the PTT button. Speak clearly into the microphone. 6 Release the PTT to end the transmission. 7 Press and hold the preprogrammed Emergency button until a tone sounds to exit Emergency mode. Turning the radio off also cancels the emergency state. s e r u t a e F d e c n a v d A 58 English Sending a Silent Emergency Alarm

This feature allows you to send an Emergency Alarm to another radio without any audio or visual indicator. Upon acknowledgement, your radios microphone is automatically activated, allowing you to communicate with the other radio without pressing the PTT button. This activated microphone state is also known as hot mic. Note:

If you press the PTT button during hot mic, and continue to press it after the hot mic duration expires, the radio continues to transmit until you release the PTT button. Procedure:

1 Press the preprogrammed Emergency button to activate the silent alarm feature. 2 Press and hold the emergency button until a tone sounds to exit the silent alarm mode. If silent emergency alarm is used with emergency call, pressing the PTT button exits the silent mode and initiates the emergency call. O5Head_6875947M01_C.book Page 59 Wednesday, October 20, 2010 12:13 PM Special Considerations for Emergencies

If you press the emergency button while in a channel that has no emergency capability, a low-pitched tone sounds. If the unit is out of the range of the system and/or the emergency alarm is not acknowledged, a tone sounds and the display shows NO ACKNOWLEDGE. If you press the emergency button, then change to a mode that has no emergency capability, the display shows NO EMERGENCY and a continuous low-pitched tone sounds until a valid emergency mode is selected or until the emergency is cancelled. When an emergency is active, changing to another mode where emergency is enabled (trunked or conventional) causes an emergency alarm and/or emergency call to be active on the new mode. A d v a n c e d F e a t u r e s 59 English O5Head_6875947M01_C.book Page 60 Wednesday, October 20, 2010 12:13 PM Advanced FeaturesAutomatic Registration Service (ARS) This feature provides an automated data application registration for the radio. When you turn on the radio, the device automatically registers with the server. Data applications within the fixed network can determine the presence of a device on the system and send data to the device. For example: Text Messaging Service (TMS). The Automatic Registration Service for the radio consists of two

(2) modes:

ARS Server Mode (default mode) ARS Non Server Mode Note:

The default ARS mode can be changed by a qualified radio technician using the radios programming software. s e r u t a e F d e c n a v d A 60 English Selecting or Changing ARS Mode

Procedure:

1 After the zone you want is displayed, toggle until the display shows the required channel. OR Press and hold > or < to CHAN. Press the Menu Select button directly below CHAN. The display shows the current zone is not blinking, and the channel is blinking. 2 > or < or rotate the Mode Knob to the required channel. 3 In ARS Server Mode, the display shows the User Login Indicator icon, the zone, and ARS server channel. OR In ARS Non-Server Mode, the display shows the User Login Indicator icon, the zone, and ARS non-server channel. OR If the channel or mode selected is unprogrammed, the display shows UNPROGRAMMED. Repeat Step 2. 4 Press H to confirm the displayed zone and channel. O5Head_6875947M01_C.book Page 61 Wednesday, October 20, 2010 12:13 PM Accessing the User Login Feature

This feature allows you as the user to be associated with the radio. With this association, every data application (Example:

Text Messaging Service) takes on a friendly username. You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message. Note:

Valid characters for a username entry are capital letters (A Z), small letters (a z), numbers (0 9), symbols (*, #, -, /), and the space character. The maximum length for a username is eight (8) characters. Usernames are not case sensitive in server mode but are case sensitive in non-server mode. A predefined username may sometimes be invalid because the programming software that is used to set predefined usernames allows you to set usernames comprising of eight (8) characters or more. A d v a n c e d F e a t u r e s Logging In as a User

Procedure:

1 > or < to USER. 2 Press the Menu Select button directly below USER. 3 The display shows the User Login screen. 4 Press the Menu Select button directly below ID. 5 A blinking cursor appears beside ID. Use the keypad to enter a username using the keypad multi-tap function. OR

> or < to scroll through the list of predefined usernames. Press the Menu Select button to select a predefined username. OR Press and hold > or < to scroll through the list of predefined usernames at a fast scroll rate. Press the Menu Select button directly below LOGN to select a predefined username. 6 If the selected predefined username has more than eight (8) characters, or an invalid character in it, the display momentary shows INVALID ID. Repeat Step 5. OR Press the Menu Select button directly below PIN. 7 A blinking cursor appears beside PIN. Enter your Personal Identification Number (PIN) number. 61 English O5Head_6875947M01_C.book Page 62 Wednesday, October 20, 2010 12:13 PM The maximum PIN length is 4 digits. The PIN number will appear as asterisks. 8 Press the Menu Select button directly below LOGN. 9 In ARS server mode, the display shows the User Login Indicator icon, the ID, IN PPROGRESS and CNCL. OR In ARS non-server mode, the display shows the User Login Indicator icon, the ID, LOGGED IN and LOGT. In non-ARS enabled mode, the display shows OFFLINE and LOGT. 10 If the username is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also momentary shows LOGIN FAILED. Repeat step 5. OR If the PIN is invalid, login fails and the user login failure indicator (IP indicator) icon blinks. The display also momentary shows LOGIN FAILED. Repeat Step 7. OR Press the Menu Select button directly below CNCL to cancel the login in progress screen and return to the initial user login screen. OR Wait for the logged in confirmation screen. If the login process is successful, the display shows the successful user login indicator (IP indicator) icon and LOGGED IN and LOGT. s e r u t a e F d e c n a v d A 62 English Logging Out

Once the data application registration is completed, you can log out. Procedure:

1 > or < to LOGT. 2 Press the Menu Select button directly below LOGT. 3 Display shows the User Login Indicator icon and CLEAR PRIVATE DATA?. 4 Select YES to clear all your private data. The display shows momentary PRIVATE DATA CLEARED. OR Select NO to keep your private data. Note:

Private data refers to all messages in the text messaging Inbox, Draft and Sent folder. The next radio user will be able to access your Inbox, Draft and Sent messages if private data is not deleted. O5Head_6875947M01_C.book Page 63 Wednesday, October 20, 2010 12:13 PM Text Messaging Service (TMS) This feature allows you to send and receive text messages. The maximum length of characters for a text message is 200. There are three (3) types of text messages:

A new text message (free form message) A predefined message (quick text message) An edited quick text message The main menu consists of the following options:

Inbox Compose Drafts Sent Note:

See Status Icons on page 19 for more details on the TMS icons and TMS Menu Options on page 20 for more details on each menu option. Accessing TMS Feature

Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Press the Menu Select button directly below BACK at any time to return to the previous screen. Procedure:

Press the preprogrammed Data Feature button or the TMS button to access the TMS feature screen. OR Press and hold the preprogrammed Data Feature button or the TMS button to access the Inbox screen. OR Follow the procedure below. 1 > or < to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 > or < to scroll through the main menu options. A d v a n c e d F e a t u r e s 63 English O5Head_6875947M01_C.book Page 64 Wednesday, October 20, 2010 12:13 PM

Note:

Composing and Sending a New Text Message During the uppercase and lowercase mode, multi-

tapping the keys only scrolls through the letters. For example, A->B->C, a->b->c. During the num lock mode, except for 1, pressing the keypad only enters the numeric digits. Subsequent presses of the same key inserts the same digit to the text message (no multi-tap). Procedure:

1 > or < to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 Press the Menu Select button directly below COMP to see the compose options. 4 Press the Menu Select button directly below NEW to compose a new message. 5 A blinking cursor appears on the Compose screen. Use the keypad to type or edit your message. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button directly below DEL to delete any unwanted characters. Press * to add a space. s e r u t a e F d e c n a v d A 64 English Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 6 Press the Menu Select button directly below OPTN once the message is composed. 7 > or < to SEND and press the Menu Select button directly below SEND to send. OR

> or < to BACK and press the Menu Select button directly below BACK to return to Compose screen if you want to edit the message. 8 > or < to scroll through the address list and press the Menu Select button below SEL to select the required address. OR

> or < to {OTHER RECPNT} and press the Menu Select button below EDIT. A blinking cursor appears in the ENTER ADDRESS screen. Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below DEL to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. O5Head_6875947M01_C.book Page 65 Wednesday, October 20, 2010 12:13 PM 9 Press the Menu Select button below SEND to send the message. OR Press the PTT button to send the message. 10 The display shows the SEND MESSAGE screen and SENDING MSG. 11 If the message is sent, a tone sounds and the display shows MSG SENT. OR If the message is not sent, a low tone sounds and the display shows SEND FAILED. If the message fails to send, the radio returns you to the main TMS screen. Note:

You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 67 for more information. Note:

You can also select the DRFT option to save your message in the Drafts folder to send it at a later time. See Accessing the Drafts Folder on page 71 for more details. Sending a Quick Text Message

Quick Text messages are messages that are predefined and usually consist of messages that are used most frequently. Each Quick Text message has a maximum length of 50 characters. Procedure:

Press the preprogrammed Quick Text button and proceed to Step 3. OR Follow the procedure below. 1 > or < to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 Press the Menu Select button directly below COMP to access the compose options. 4 > or < to LIST. 5 > or < to scroll through the list of messages and press the Menu Select button directly below SEL to select the required message. A d v a n c e d F e a t u r e s 6 The message appears on the Compose screen, with a blinking cursor at the end of it. Use the keypad to edit the message. Press < to move one space to the left. 65 English 10 Press the Menu Select button below SEND to send the message. OR Press the PTT button to send the message. 11 The display shows the screen and SENDING MSG. 12 If the message is sent, a tone sounds and the display shows MSG SENT. OR If the message is not sent, a low tone sounds and the display shows SEND FAILED. If the message fails to send, the radio returns you to the main TMS screen. Note:

You can append a priority status and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 67 for more information. O5Head_6875947M01_C.book Page 66 Wednesday, October 20, 2010 12:13 PM Press > to move one space to the right. Press the Menu Select button directly below DEL to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 7 Press the Menu Select button directly below OPTN. 8 > or < to SEND and press the Menu Select button directly below SEL to send the message. 9 > or < to scroll through the address list and highlight the required address. OR

> or < to {OTHER RECPNT} and press the Menu Select button below EDIT. A blinking cursor appears in the ENTER ADDRESS screen. Use the keypad to type the address entry. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below DEL to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. s e r u t a e F d e c n a v d A 66 English O5Head_6875947M01_C.book Page 67 Wednesday, October 20, 2010 12:13 PM

Using the Priority Status and Request Reply Features Before sending your message, you can append a priority message and/or a request reply to your message.

Appending or Removing a Priority Status to a Text Message Note:

The Priority Message icon on a message does not imply that the message gets higher priority over the other messages when it is being transmitted. It is just an indication that can be embedded into a message to let the receiver know that the message is important. Procedure:

After the outgoing message is composed (see Composing and Sending a New Text Message on page 64 for more information):

1 Press the Menu Select button directly below OPTN. 2 Press the Menu Select button directly below IMPT. The priority status icon appears beside the normal message icon on the label bar. 3 Press the Menu Select button directly below IMPT again. The priority status icon and the normal message icon disappear from the label bar.

Appending or Removing a Request Reply to a Text Message Procedure:

After the outgoing message is composed (see Composing and Sending a New Text Message on page 64 for more information):

1 Press the Menu Select button directly below OPTN. 2 Press the Menu Select button directly below RQRP. The reply status icon appears beside the normal message icon on the label bar. 3 Press the Menu Select button directly below RQRP again. The reply status icon and the normal message icon disappear from the label bar.

Appending a Priority Status and a Reply Request to a Text Message A d v a n c e d F e a t u r e s Procedure:

After the outgoing message is composed (see Composing and Sending a New Text Message on page 64 for more information):

1 Press the Menu Select button directly below OPTN. 2 > or < to IMPT and press the Menu Select button directly below IMPT to indicate the message as important. AND 67 English O5Head_6875947M01_C.book Page 68 Wednesday, October 20, 2010 12:13 PM

> or < to RQRP and press the Menu Select button directly below RQRP to request for a reply. 3 The priority status and reply status icons appear beside the normal message icon on the label bar.

Removing a Priority Status and a Reply Request from a Text Message When an outgoing message is indicated with priority status and reply status icons, follow the procedure below to remove these indicators. Procedure:

1 Press the Menu Select button directly below OPTN. 2 > or < to IMPT and press the Menu Select button directly below IMPT to remove the priority status icon. AND

> or < to RQRP and press the Menu Select button directly below RQRP to remove the reply status icon. 3 The priority status, reply status and normal message icons disappear from the label bar.

Managing Text Messages Receiving a Text Message

Note: When you receive a message that is flagged with the Request Reply icon, you must manually respond to the sender that you have received the message. The system will not automatically send back a notification that the radio has received such message. Procedure:

When you receive a message, press and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox and go to Step3. OR Follow the procedure below. 1 The new message icon appears and the display momentarily shows NEW MSG. 2 Press the Menu Select button directly below TMS to access the message. 3 The display shows alias or ID with the sender of the latest received message on top. s e r u t a e F d e c n a v d A 68 English O5Head_6875947M01_C.book Page 69 Wednesday, October 20, 2010 12:13 PM Viewing a Text Message from the Inbox

The Inbox can hold up to thirty (30) messages. Note:

> or < to read the message if fills more than one screen. Procedure:

Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3. OR Press and hold the preprogrammed Data Feature button or the TMS Feature button to access the Inbox screen and proceed to Step 4. OR Follow the procedure below. 1 > or < to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 Press the Menu Select button below INBX to view Inbox feature screen. 4 The display shows alias or IDs, with the sender of the latest received message. While on the review message screen, press the Menu Select button directly below RPLY, DEL, or BACK to access the option. Select RPLY to reply the message. Select DEL to delete the message. Select BACK to return to the previous screen. Note:

The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) on page 63 for more information. A d v a n c e d F e a t u r e s 69 English O5Head_6875947M01_C.book Page 70 Wednesday, October 20, 2010 12:13 PM Replying to a Received Text Message

Note:

The original date and time stamp, address and message content is automatically appended to the reply message. Procedure:

1 > or < to the required aliases or ID and press the Menu Select button below SEL to view the message. 2 Press the Menu Select button directly below RPLY to reply to a message. 3 > or < to NEW and press the Menu Select button directly below NEW. OR

> or < to LIST and press the Menu Select button directly below LIST for a predefined message. OR

> or < to scroll through the list of messages and press the Menu Select button directly below SEL to select the required message. 4 A blinking cursor appears on the screen. OR The predefined message appears on the Compose screen, with a blinking cursor at the end of it. s e r u t a e F d e c n a v d A 5 Use the keypad to type or edit your message. Press < to move one space to the left. 70 English Press > to move one space to the right. Press the Menu Select button below DEL to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 6 Press the Menu Select button directly below OPTN once you have finished writing the message. 7 > or < to SEND and press the Menu Select button directly below SEND to send the message. 8 The display shows the Send Message screen and SENDING MSG. Press the Menu Select button directly below BACK at any time to return to the previous screen. Note:

You can append a priority message and/or a request reply to your message. Using the Priority Status and Request Reply Features on page 67 for more information. O5Head_6875947M01_C.book Page 71 Wednesday, October 20, 2010 12:13 PM Accessing the Drafts Folder

This folder stores the messages that were saved previously. The Drafts folder can hold up to 10 messages. The oldest draft in the folder is deleted when the 11th message comes in. Procedure:

1 > or < to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 > or < to DRFT and press the Menu Select button below DRFT. 4 The display shows the first draft message. Press the Menu Select button directly below EDIT, DEL, or BACK to access the option. Select EDIT to edit the message before sending it. Select DEL to delete the message. Select BACK to return to the previous screen. A d v a n c e d F e a t u r e s Managing Sent Text Messages

Once a message is sent to another radio, it is saved in the Sent folder. The most recent sent text message is always added to the top of the Sent list. The Sent folder is capable of storing a maximum of ten (10) last sent messages. When the folder is full, the oldest text message in the folder is deleted when the 11th message comes in. Viewing a Sent Text Message

The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) on page 63 for more information. Procedure:

Press the preprogrammed Data Feature button or the TMS Feature button to access the TMS feature screen, and proceed to Step 3. OR Follow the procedure below. 1 > or < to TMS. 2 Press the Menu Select button directly below TMS to access the TMS feature screen. 3 > or < to SENT and press the Menu Select button below SENT. 71 English O5Head_6875947M01_C.book Page 72 Wednesday, October 20, 2010 12:13 PM Press the Menu Select button directly below OPTN, DEL, or BACK to access the option. Select OPTN to send to the message. Select DEL to delete the message. Select BACK to return to the previous screen. Note:

The icon at the top right corner of the screen indicates the status of the message. See Text Messaging Service (TMS) Icons on page 19 for more information. Sending a Sent Text Message

Procedure:

1 Press the Menu Select button directly below OPTN while viewing the message. 2 > or < to SEND and press the Menu Select button directly below SEND to send the message. 3 > or < to scroll through the address list and highlight the required address. OR

> or < to {OTHER RECPNT} and press the Menu Select button below EDIT. A blinking cursor appears in the ENTER ADDRESS screen. Use the keypad to type the address entry. Press < to move one space to the left. s e r u t a e F d e c n a v d A 72 English Press > to move one space to the right. Press the Menu Select button below DEL to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 4 Press the Menu Select button below SEND or the PTT button to send the message. 5 The display shows the Send Message screen and SENDING MSG. 6 Press the Menu Select button directly below BACK to return to the previous screen. Note:

You can append a priority message and/or a request reply to your message. See Using the Priority Status and Request Reply Features on page 67 for more details. O5Head_6875947M01_C.book Page 73 Wednesday, October 20, 2010 12:13 PM Deleting Text Messages

Procedure:

From the Inbox, Draft, or Sent screen:

1 > or < to scroll through the messages. 2 Press the Menu Select button directly below DEL to view the delete options. 3 Press the Menu Select button directly below CURR to delete the current message. OR Press the Menu Select button directly below ALL to delete all the messages. Secure Operations Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels. Unlike other forms of security, Motorola digital encryption provides signaling that makes it virtually impossible for others to decode any part of an encrypted message. Managing Encryption

Note: Refer to the Key-Variable Loader (KVL) manual for equipment connections and setup. Loading a Single Encryption Key

Procedure:

1 Attach the KVL to your radio. Upon attaching the KVL, the radio display shows KEYLOADING. A d v a n c e d F e a t u r e s 2 Press the Menu Select button below TARGET. 3 Press the Menu Select button below LOAD. 4 Press the Menu Select button below KEY. 5 > or < to required key. 6 Press the Menu Select button below LOAD to load the key to your radio. 73 English Using the Multikey Feature

This feature allows the radio to be equipped with different encryption keys and supports the DES-OFB algorithm. There are two types of multikey:

Conventional Multikey The encryption keys can be tied

(strapped), on a one-per-channel basis, through Customer Programming Software. In addition, you can have operator-

selectable keys, operator-selectable keysets, and operator-

selectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups. Trunked Multikey If you use your radio for both conventional and trunked applications, you have to strap your encryption keys for trunking on a per-talkgroup or announcement-group basis. In addition, you may strap a different key to other features, such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operator-

selectable key erasure. O5Head_6875947M01_C.book Page 74 Wednesday, October 20, 2010 12:13 PM 7 When the key has been loaded successfully, the radio sounds a short tone for single-key radios. Loading the Group Encryption Keys

Procedure:

1 Attach the KVL to your radio. 2 Press the Menu Select button below TARGET. 3 Press the Menu Select button below LOAD. 4 Press the Menu Select button below GROUP. 5 > or < to required group. 6 Press the Menu Select button below LOAD to load the key to your radio. 7 Your mobile radio display shows KEYLOADING when it is loading key(s) from KVL. 8 When the key has been loaded successfully, the radio sounds an alternating tone for multikey radios. s e r u t a e F d e c n a v d A 74 English O5Head_6875947M01_C.book Page 75 Wednesday, October 20, 2010 12:13 PM Selecting an Encryption Key (Conventional Only)

Procedure:

1 > or < to KEY. 2 Press the Menu Select button directly below KEY. The display shows the last user-selected and stored encryption key, and the available menu selections. 3 > or < to scroll through the encryption keys. OR Use the keypad to enter the number of the desired key. 4 Press the Menu Select button directly below SEL to save the newly selected key and return to the Home screen. OR Press H, the PTT button, or the Menu Select button directly below EXIT to exit. Note:

If the selected key is erased, a momentary keyfail tone sounds and the display shows KEY FAIL. OR If the selected key is not allowed, a momentary illegal key tone sounds and the display shows ILLEGAL KEY. Enabling Secure Transmission

Procedure:

1 > or < to SEC and press the Menu Select button directly below SEC. The display shows m and the current key if multi-key has been enabled. 2 Monitor the mode to be sure it is not in use. 3 Press PTT button to transmit. Note:

If the selected channel is preprogrammed for clear-

only operation when you press the PTT button, an invalid mode tone sounds and the display shows CLEAR TX only. The radio does not transmit until you disable the secure mode. A d v a n c e d F e a t u r e s Accessing the Secure Feature

Procedure:

1 > or < to SEC. 2 Press and hold the Menu Select button directly below SEC to display Secure feature screen. 3 The display shows the Secure screen. 75 English O5Head_6875947M01_C.book Page 76 Wednesday, October 20, 2010 12:13 PM Selecting a Keyset

This feature allows you to select one or more groups of several encryption keys from among the available keys stored in the radio. For example, you could have a group of three keys structured to one keyset, and another group of three different keys structured to another keyset; by changing keysets, you would automatically switch from one set of keys to the other. Every channel to which one of the original keys was tied now has the equivalent new key instead. Note: Press H, the PTT button, or the EXIT menu selection to exit this menu at any time without changing the keyset selection. Procedure:

1 > or < to KSET. 2 Press the Menu Select button directly below KSET. The display shows the last user-selected and stored keyset, and the available keyset menu selections. 3 > or < to scroll through the keysets. OR Use the keypad to enter the number of the desired keyset. s e r u t a e F d e c n a v d A 5 The radio exits keyset selection and returns to the Home screen. Erasing the Selected Encryption Keys

This feature allows you to erase all or selected encryption keys. Procedure:

1 > or < to ERAS. 2 Press the Menu Select button directly below ERAS. The display shows the last user-selected and stored encryption key, and the available menu selections. 3 > or < to the desired encryption key. OR Use the keypad to enter the number of the desired key. 4 Press the Menu Select button directly below ALL to delete all keys. OR Press the Menu Select button directly below SNGL to delete current shown key. OR Press the Menu Select button directly below ABRT to abort this screen and return to Home screen. 4 Press the Menu Select button directly below SEL to save the newly selected keyset. 76 English O5Head_6875947M01_C.book Page 77 Wednesday, October 20, 2010 12:13 PM Requesting an Over-the-Air Rekey

This feature, also known as OTAR, allows the dispatcher to reprogram the encryption keys in the radio remotely. The dispatcher performs the rekey operation upon receiving a rekey request from the user. Procedure:

1 > or < to REKY. 2 Press the Menu Select button directly below REKY. 3 Press the PTT button to send the rekey request. OR Press the PTT button again, or the H or Emergency button, to exit the feature and transmit in normal mode. MDC Over-the-Air Rekeying (OTAR) Page

This feature allows to view or define MDC Over-the-Air Rekeying (OTAR) features.It is applied only when operating in secure encrypted mode and only for conventional communications. In additional to Rekey Requests, OTAR transmissions include Delayed Acknowledgements, and Power-

up Acknowledgements. Some of the options selected may also need to be set up at the Key Management Controller (KMC) site to work properly. Note:

This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. A d v a n c e d F e a t u r e s 4 If the rekey operation fails, a bad-key tone sounds and the display shows REKEY FAIL. Note:

The rekey operation failure indicates that your radio does not contain the Unique Shadow Key (USK). This key must be loaded into the radio with the key-variable loader (KVL) before the rekey request can be sent. Refer to your local key management supervisor for more information. 77 English O5Head_6875947M01_C.book Page 78 Wednesday, October 20, 2010 12:13 PM Hear Clear

There are two components of Hear Clear. 1 Companding:

Reduces the channel noise, e.g. OTA transmission, that is predominantly present in UHF2 and 900 MHz channel with the following features. Compressor reduces the background noise flow and the speech signal at transmitting radio. Expander expands the speech while the noise flow remains the same at receiving radio. 2 Random FM Noise Canceller (Flutter Fighter):

Reduces the unwanted effects of random FM noise pulses caused by channel fading under high Signal-to-Noise (S/N) conditions such as in a moving in a transportation. The fading effects, heard as audio pops and clicks, are cancelled without affecting the desired audio signal. The Random FM Noise Canceller operates only in receive mode. Note:

This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. s e r u t a e F d e c n a v d A 78 English The Global Positioning System (GPS) This feature uses information from the Global Positioning System (GPS) satellites orbiting the Earth to determine the approximate geographical location of your radio, expressed as latitude and longitude. The availability and accuracy of this location information (and the amount of time that it takes to calculate it) varies depending on the environment in which you are using the GPS feature. For example, GPS location fixes are very difficult to obtain indoors, in covered locations, between high buildings, or in situations where you have not established a clear broad view of the sky. Understanding the GPS Feature

The GPS technology uses radio signals from earth orbiting satellites, to establish the location co-ordinates, maximizing your view of clear unobstructed sky is essential for optimum performance. Where adequate signals from multiple satellites are not available (usually because you cannot establish a view of a wide area of the sky), the GPS feature of your radio will not work. Such situations include but are not limited to:

In underground locations Inside of buildings, trains, or other covered vehicles O5Head_6875947M01_C.book Page 79 Wednesday, October 20, 2010 12:13 PM Under any other metal or concrete roof or structure Between tall buildings or under dense tree-cover In temperature extremes outside the operating limits of your radio Even where location information can be calculated in such situations, it may take longer to do so, and your location estimate may not be as accurate. Therefore, in any emergency situation, always report your location to your dispatcher. Note:

Even where adequate signals from multiple satellites are available, your GPS feature only provides an approximate location, usually within 20 meters from your actual location, but sometimes further away. Keep in mind that the accuracy of the location information and the time it takes to obtain it varies depending upon circumstances, particularly the ability to receive signals from an adequate number of satellites. Note:

The satellites used by the GPS feature are controlled by the U.S. government and are subject to changes implemented in accordance with the Department of Defense GPS user policy and the Federal Radio Navigation Plan. These changes may affect the performance of the GPS feature on your radio. Enhancing GPS Performance

Sometimes, the GPS feature may be unable to complete a location calculation successfully. You then see a message indicating that your radio cannot connect to enough visible satellites. To maximize the ability of your radio to determine a fix, please note the following guidelines:

For your initial fix, hold the radio in the face position. Stay in the open. The GPS feature works best where there is nothing between your radio and a large amount of open sky. The Outdoor Location Feature (Using GPS)

This feature allows you to determine your current location using a location menu, as well as your current distance and bearing in relation to another location. Radio location may be requested and reported over-the-air. Your radio stores up to a maximum of sixty (60) programmable location coordinates, also known as waypoints. When the memory is full, the next waypoints automatically replaces the oldest waypoints in the radio. A d v a n c e d F e a t u r e s 79 English O5Head_6875947M01_C.book Page 80 Wednesday, October 20, 2010 12:13 PM The radio also stores four (4) preprogrammed waypoints. These coordinates cannot be deleted. Programmable Waypoints User-configurable location coordinates. Only the alias is editable, not the coordinates. Coordinates can be deleted one at a time, or all at once. Preprogrammed Waypoints Fixed location coordinates:

Home Emergency Last Known Location Destination The Home and Destination coordinates are editable. Coordinates cannot be deleted. Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. s e r u t a e F d e c n a v d A 80 English

Note:

Accessing the Outdoor Location Feature An ON menu key may be present on the location menu if it is preprogrammed by the dealer or system administrator. Procedure:

1 > or < to LOC. 2 Press the Menu Select button directly below LOC. The display shows LOCATION OFF <LATITUDE>. 3 Press the Menu Select button directly below ON to turn on the GPS. The display shows PREVIOUS LOC <LATITUDE>. 4 > or < to check the longitude, time and date of the last successful location fix. 5 Press the Menu Select button directly below RFSH to obtain a new location fix. 6 The top line temporarily displays PLEASE WAIT while the new location is being determined. While the new location is being determined, the location signal can be a solid or blinking icon. 7 Once the location coordinates are fixed, the display shows the current latitude. Toggle to see the longitude, time and date. The location coordinates are updated automatically every five seconds while the location signal is present. O5Head_6875947M01_C.book Page 81 Wednesday, October 20, 2010 12:13 PM 8 Press the Menu Select button directly below EXIT to exit the feature and return to the main screen. OR Press H or the PTT button (if preprogrammed) to exit this menu. OR Follow the procedure below to turn off the GPS (This feature is enabled by a qualified radio technician.):

1 > or < to LOC. 2 Press the Menu Select button directly below LOC. The display shows PREVIOUS LOC <LATITUDE>. 3 > or < to check the longitude, time and date of the last successful location fix. 4 Press the Menu Select button directly below OPTN. 5 > or < to TURN OFF GPS (if preprogrammed). 6 Press the Menu Select button directly below SEL to turn off the GPS. The display shows LOCATION OFF. 7 Press the Menu Select button directly below EXIT to exit the feature and return to the main screen. OR Press H or the PTT button (if preprogrammed) to exit this menu. The radio also exits the menu if the emergency button is pressed. Saving a Waypoint

Procedure:

While in the current location display:

1 Press the Menu Select button directly below OPTN. 2 > or < to SAVE AS WAYPT and press the Menu Select button directly below SEL. OR

> or < to SAVE AS HOME and press the Menu Select button directly below SEL and proceed to Step 5. OR

> or < to SAVE AS DEST. and press the Menu Select button directly below SEL and proceed to Step 5. A d v a n c e d F e a t u r e s 3 A blinking cursor appears in the screen. Use the keypad to type the alias via multi-tap. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below DEL to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 81 English O5Head_6875947M01_C.book Page 82 Wednesday, October 20, 2010 12:13 PM 4 Press the Menu Select button directly below OK once you are done. 5 The display shows SAVED AS <WAYPOINT NAME>. OR The display shows SAVED AS HOME. OR The display shows SAVED AS DEST.. 6 Press H or the PTT button (if preprogrammed) to exit this menu. 8 Press the Menu Select button directly below BACK to return to previous Waypoint screen. OR Press H or the PTT button (if preprogrammed) to exit this menu. Viewing a Saved Waypoint

Procedure:

While in the current location display:

1 Press the Menu Select button directly below OPTN. 2 > or < to WAYPOINTS. 3 Press the Menu Select button directly below SEL. 4 > or < to desired waypoint. 5 Press the Menu Select button directly below OPTN. The display shows VIEW. s e r u t a e F d e c n a v d A 6 Press the Menu Select button directly below SEL. 7 > or < again to view longitude, time and date the waypoint was detected. 82 English O5Head_6875947M01_C.book Page 83 Wednesday, October 20, 2010 12:13 PM Editing the Alias of a Waypoint

Procedure:

While in the current location display:

1 Press the Menu Select button directly below OPTN. 2 > or < to WAYPOINTS. 3 Press the Menu Select button directly below SEL. 4 > or < to desired waypoints. 5 Press the Menu Select button directly below OPTN. 6 > or < to EDIT NAME and press the Menu Select button directly below SEL. 7 A blinking cursor appears in the Edit Name screen. Use the keypad to edit the alias. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below DEL to delete any unwanted characters. Press * to add a space. Press 0 to toggle between mixed case mode, uppercase mode, and lowercase mode. Press # to toggle between numeric and letter mode. 8 Press the Menu Select button directly below OK once you are done. OR Press the Menu Select button directly below CNCL to return to the Waypoints main screen. 9 The display shows <WAYPOINT NAME> UPDATED. 10 Press H or the PTT button (if preprogrammed) to exit this menu. Editing the Coordinates of a Waypoint

Procedure:

While in the current location display:

1 Press the Menu Select button directly below OPTN. 2 > or < to WAYPOINTS and press the Menu Select button directly below SEL. A d v a n c e d F e a t u r e s 3 > or < to desired waypoints. 4 Press the Menu Select button directly below OPTN. 5 > or < to EDIT LOCATION and press the Menu Select button directly below SEL. 6 The first number blinks. Press < to move to the previous number/coordinates. Press > to move to the next number/coordinates. Press U or D to change the North (N), South (S), East (E) or West (W) direction. 83 English O5Head_6875947M01_C.book Page 84 Wednesday, October 20, 2010 12:13 PM Press the Menu Select button below EDIT to change the number/coordinates. 7 A blinking cursor appears in the EDIT LOCATION screen. Press < to move one space to the left. Press > to move one space to the right. Press the Menu Select button below Del to delete any unwanted characters. 8 Press the Menu Select button directly below OK once you are done. OR Press the Menu Select button directly below CNCL to return to the previous screen. 9 Press the Menu Select button directly below OK once you are done with the new coordinates. OR Press the Menu Select button directly below CNCL to return to the previous screen then skip to step 11. 10 The display shows {HOME} UPDATED and the radio returns to the Waypoints main screen. OR The display shows {DESTINATION} UPDATED and the radio returns to the Waypoints main screen. 11 Press H or the PTT button (if preprogrammed) to exit this menu. s e r u t a e F d e c n a v d A 84 English Deleting a Single Saved Waypoint

Procedure:

While in the current location display:

1 Press the Menu Select button directly below OPTN. 2 > or < to WAYPOINTS. 3 Press the Menu Select button directly below SEL. 4 > or < to desired waypoints. 5 Press the Menu Select button directly below OPTN. OR Press the Menu Select button directly below DEL and then skip to step 7. 6 > or < to DELETE and press the Menu Select button directly below SEL. 7 The display shows <WAYPOINT NAME> CONFIRM DEL?. 8 Press the Menu Select button directly below YES to delete. The display shows <WAYPOINT NAME> DELETED. OR Press the Menu Select button directly below NO to return to previous Waypoint screen. 9 Press H or the PTT button (if preprogrammed) to exit this menu. O5Head_6875947M01_C.book Page 85 Wednesday, October 20, 2010 12:13 PM Deleting All Saved Waypoints

Procedure:

1 Press the Menu Select button directly below OPTN. 2 > or < to WAYPOINTS and press the Menu Select button directly below SEL. 3 > or < to desired waypoints and press the Menu Select button directly below OPTN. 4 > or < to DELETE ALL and press the Menu Select button directly below SEL. 5 The display shows ALL SAVED WAYP CONFIRM DEL?. 6 Press the Menu Select button directly below YES to delete. The display shows ALL SAVED WAYP DELETED. OR Press the Menu Select button directly below NO to return to previous Waypoint screen. 7 Press H or the PTT button (if preprogrammed) to exit this menu.

Measuring the Distance and Bearing from a Saved Waypoint Procedure:

While in the current location display:

1 Press the Menu Select button directly below OPTN. 2 > or < to DIST FRM HERE and press the Menu Select button directly below SEL. 3 > or < to the required waypoint, and press the Menu Select button directly below SEL. 4 The display shows the distance and bearing from the current to the selected coordinates. 5 Press the Menu Select button directly below BACK to return to the previous Waypoint screen. OR Press H or the PTT button (if preprogrammed) to exit this menu. A d v a n c e d F e a t u r e s 85 English O5Head_6875947M01_C.book Page 86 Wednesday, October 20, 2010 12:13 PM

Using the Location Feature While in Emergency Mode When the Emergency feature is activated by pressing the emergency button, the radio exits the Location menu and returns to the home (default) display so that you can see which channel the emergency signal is going out on. However, you may re-enter the Location menu while still in emergency mode, provided that Silent Emergency has not been activated. If you have turned Location off using the ON/OFF menu key, it automatically turns back on when Emergency is activated. If there is a solid location signal during Emergency, the current location and the location information received is saved as Emergency and Last Known Location waypoints, respectively. s e r u t a e F d e c n a v d A 86 English Trunking System Controls Using the Failsoft System

The failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel. The failsoft condition is indicated by a faint beeping tone every nine seconds (radio unsquelched) until the trunking system returns to normal operation. To continue, in Failsoft, to communicate with other talkgroups, refer to the following procedure. Procedure:

1 Rotate the Mode Knob to change to a different repeater frequency. 2 Press the PTT button to talk, and release the button to listen. When the trunking system returns to normal operation, your radio automatically leaves failsoft operation and returns to trunked operation. O5Head_6875947M01_C.book Page 87 Wednesday, October 20, 2010 12:13 PM Going Out-of-Range

OUT OF RANGE when your radio goes out of the range of the system, it can no longer lock onto a control channel. Procedure:

1 A low-pitched tone sounds. AND/OR The display shows the currently selected zone/channel combination and OUT OF RANGE. 2 Your radio remains in this out-of-range condition until:

It locks onto a control channel. OR It locks onto a failsoft channel. OR It is turned off. SmartZone

The SmartZone feature extends communications beyond the reach of a single-trunked site (antenna location) when operating in a SmartZone system. SmartZone units provide expanded wide-area coverage. SmartZone automatically switches the radio to a different site when the current site signal becomes unacceptable. This usually happens when the vehicle in which the radio is located is driven out of the range of one site, and into the range of another. Under normal conditions, a SmartZone-enabled radio functions invisibly to the operator. However, the operator does have some manual controls on the Control Head the RSSI menu entry. This button can be used to check, or change, the SmartZone operation. A d v a n c e d F e a t u r e s Using Site Trunking Feature

If the zone controller loses communication with any site, that site reverts to site trunking. The display shows the currently selected zone/channel combination and SITE TRUNKING. Note: When this occurs, you can communicate only with other radios within your trunking site. 87 English Viewing and Changing a Site

This feature allows you to view the number of the current site or force your radio to change to a new one. Viewing the Current Site

Procedure:

1 Press the preprogrammed Site Search button. OR

> or < to RSSI. 2 The display momentarily shows the name of the current site and its corresponding received signal strength indicator

(RSSI). O5Head_6875947M01_C.book Page 88 Wednesday, October 20, 2010 12:13 PM Locking and Unlocking a Site

This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system. Procedure:

Use the preprogrammed Site Lock/Unlock button to toggle the lock state between locked and unlocked. OR Follow the procedure below. 1 > or < to SITE. 2 Press the Menu Select button directly below SITE. 3 Press the Menu Select button directly below LOCK to lock the site. OR Press the Menu Select button directly below UNLK to unlock the site. 4 The radio saves the new site lock state and returns to the Home screen. s e r u t a e F d e c n a v d A 88 English O5Head_6875947M01_C.book Page 89 Wednesday, October 20, 2010 12:13 PM Changing the Current Site

Procedure:

1 Press and hold down the preprogrammed Site Search button. OR Press and hold down the Menu Select button directly below RSSI. 2 A tone sounds and the display momentarily shows SCANNING SITE. When the radio finds a new site, it returns to the Home screen. Trunked Announcement

The announcement capability allows you to make announcements to the entire user group, as well as monitor talkgroup calls and other announcements. Announcement calls are handled in two different ways, depending on the trunked central controller configuration. The two types are called ruthless and non-ruthless preemption. Ruthless Preemption:

When a ruthless preemption announcement call is initiated, the requesting radio begins transmitting immediately. All associated talkgroup calls taking place on other channels are immediately halted, and the radios are steered to the announcement call. A d v a n c e d F e a t u r e s Transmitting radios continue to transmit until the PTT button is released, at which time they also unmute for the announcement call. Individual calls (Private Conversation and telephone interconnect) are not affected. Non-Ruthless Preemption:

When a non-ruthless preemption announcement is initiated, the initiating unit receives a telephone-type busy tone, followed by a call back when all associated talkgroup conversations end. Once an announcement call is pending, any attempts by other users to initiate a talkgroup call will result in a telephone-type busy tone. These users will not receive a call back until the announcement call is complete. 89 English O5Head_6875947M01_C.book Page 90 Wednesday, October 20, 2010 12:13 PM Initiating an Announcement

If your radio has been programmed to allow announcement calls:

Procedure:

1 Press the Mode Knob to locate the announcement-group mode. 2 Press the microphone PTT button to initiate the announcement. s e r u t a e F d e c n a v d A 90 English Ignition Switch Options This feature allows the user to select the radios functionality based on the Ignition State of the radio users vehicle. The available options are as follows. Blank

This option allows the user to power on and power off the radio through the Power button regardless of the Ignitions current state. Tx Inhibit

This option allows the user to power on and power off the radio through the Power button regardless of the Ignitions current state. In addition, if the Ignition is not present, then all transmissions are inhibited. This includes receiving any Trunking dispatch communications since the radio will not affiliate with the Trunking systems. PTT Tx Inhibit

This option allows the user to power on and power off the radio through the Power button regardless of the Ignitions current state. In addition, if the Ignition is not present, then all PTT button transmissions are inhibited. However, the radio is able to affiliate with the Trunking systems. O5Head_6875947M01_C.book Page 91 Wednesday, October 20, 2010 12:13 PM Required

This option allows the user to power on the radio only if the Ignition is present. The radio can be powered off either through Power button press or when Ignition is lost. In addition, the radio automatically powers on when the Ignition is present only if the radio was turned off due to the ignition being removed. This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires. Soft Power Off

This option allows the user to power on the radio either through Power button presses or when the Ignition is detected. Meanwhile, if the Power button was pressed or the Ignition was removed, the radio will be turned off. This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires. Ignition Only Power Up

This option allows the user to power on the radio only when Ignition is detected and will power off when it is removed. The radio does not power on or off with the Power button press. This option allows the radio to power off when Inactivity Auto Power Off Timer expires, or, when Ignition Auto Power Off Timer expires. Note: While "Ignition" is not present, the radio powers-off with a radio-user Power Off button / knob selection if the radio was powered-up with an Emergency Power Up footswitch-press or Ignition Auto Power Off timer is running. While "Ignition" is present, the radio powers-on with a radio-user Power On button / knob selection only if the radio was powered-down with Inactivity Auto Power Off timer. Emergency Power Up

This feature allows the user to power on the radio and automatically transmits an emergency mode transmission on personalities with emergency enabled, with the use of a footswitch. In addition, when the Ignition Switch option is set to either Tx Inhibit or PTT Tx Inhibit, this feature will not be available to the users. Press the footswitch to turn on the radio and launch Emergency. A tone sounds and the display shows Emergency. A d v a n c e d F e a t u r e s 91 English O5Head_6875947M01_C.book Page 92 Wednesday, October 20, 2010 12:13 PM Auto Power Off Timer

Auto Power Off feature powers off the radio when no user actions occur during a preprogrammed length of time. There two different version of Auto Power Off:

Inactivity Auto Power Off Timer This timer begins once the radio is power-on. While the timer is active any user interaction with the radio resets the timer. Ignition Auto Power Off Timer This timer begins once the vehicle key is removed, when the voltage at the ignition sense is removed. While the timer is active any user interaction with the radio resets the timer. When the vehicle key is reapplied, the voltage at the ignition is reconnected, this timer is stopped. Although both Inactivity Auto Power Off and Ignition Auto Power Off can be enabled together, Ignition Auto Power Off timer is mutually exclusive with Inactivity Auto Power Off timer when both are enabled. During the last two minutes of the timer countdown, the radio generates continuous low tone and blinks POWERING OFF warning on the display until the timer expires or is reset. The radio automatically powers off after the timer expires. The duration of the timer is preprogrammed. s e r u t a e F d e c n a v d A 92 English Utilities Viewing Recent Calls List

This feature allows you to view the recent incoming and outgoing call information of the following call types:

Call Alert Selective Call Private Call Phone Call (Outgoing only) Note:

The radio can also be preprogrammed to log the radio IDs associated with incoming Dispatch Calls. Check with your dealer or system administrator for more information. Procedure:

1 > or < to RCNT. 2 Press the Menu Select button directly below RCNT to access the Recent Calls feature screen. 3 > or < to scroll through the list. 4 Press the Menu Select button directly below BACK to return to Home screen. OR Press H or the PTT button to return to the Home screen. O5Head_6875947M01_C.book Page 93 Wednesday, October 20, 2010 12:13 PM If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. 3 The display shows LOW POWER and the low power icon. OR The display shows HIGH POWER and the high power icon. Selecting the Power Level

You can select the power level at which your radio transmits. The radio always turns on to the default setting. Note:

This feature must be preprogrammed by a qualified radio technician. Settings:

Select LOW for a shorter transmitting distance and to conserve power. Select HIGH for a longer transmitting distance. Procedure:

Use the preprogrammed Transmit Power Level Switch to toggle transmit power level between high and low. OR Follow the procedure below. 1 > or < to PWR. 2 Press the Menu Select button directly below PWR. A d v a n c e d F e a t u r e s Selecting a Radio Profile

This feature allows you to manually switch the visual and audio settings of the radio. The display, backlight, alert tones, and audio settings are defined according to the preprogrammed radio settings of each radio profile. Please refer to a qualified technician for more information. Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit. Procedure:

Use the preprogrammed Profile button and proceed to Step 3. OR Follow the procedure below. 1 > or < to PRFL. 2 Press the Menu Select button directly below PRFL to access the Profiles feature screen. 3 > or < to scroll through the menu selections. 4 Press the Menu Select button directly below SEL to select the required radio profile. 93 English Turning Keypad Tones On or Off

You can enable and disable keypad tones as needed. Procedure:

Press the preprogrammed Keypad Mute button to turn the tones on or off. OR Follow the procedure below. 1 > or < to MUTE. 2 Press the Menu Select button directly below MUTE. 3 The display momentarily shows TONES OFF, indicating that the keypad tones are disabled. OR The display momentarily shows TONES ON, and a short tone sounds, indicating that the keypad tones are enabled. O5Head_6875947M01_C.book Page 94 Wednesday, October 20, 2010 12:13 PM OR Press the Menu Select button directly below EXIT to exit the screen without making any changes. 5 The radio returns to the Home screen. The profile name on the Home screen indicates the current selected radio profile. Controlling the Display Backlight

You can enable or disable the radios display backlight as needed, if poor light conditions make the display difficult to read. Depending on how your radio is preprogrammed, you can also maintain a minimum backlight level on the radios display. Procedure:

Note:

Press the DIM button to toggle the backlight on or off. OR Press any key of the keypad, the Menu Select or Menu Navigation buttons, or any programmable radio controls or buttons to turn the backlight on. s e r u t a e F d e c n a v d A 94 English O5Head_6875947M01_C.book Page 95 Wednesday, October 20, 2010 12:13 PM Turning Voice Mute On or Off

You can enable and disable voice muting of the affiliated trunking talkgroup or selected conventional channel as needed. Procedure:

Press the preprogrammed Voice Mute button to turn the feature on or off. OR Follow the procedure below. 1 > or < to VMUT. 2 Press the Menu Select button directly below VMUT. 3 The display momentarily shows VOICE MUTE OFF, and a short tone sounds, indicating that the feature is disabled. OR The display momentarily shows VOICE MUTE ON, and a short tone sounds, indicating that the feature is enabled. A d v a n c e d F e a t u r e s Using the Time-Out Timer

This feature turns off your radios transmitter. You cannot transmit longer than the preset timer setting. If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone. The timer is defaulted at 60 seconds, but it can be preprogrammed from 3 to 120 seconds, in 15-second intervals, or it can be disabled entirely for each radio mode, by a qualified radio technician. Note:

You will hear a brief, low-pitched, warning tone four seconds before the transmission times out. Procedure:

1 Hold down the PTT button longer than the preprogrammed time. You hear a short, low-pitched warning tone, the transmission is cut-off, and the LEDs goes out until you release the PTT button. 2 Release the PTT button. The LEDs relight and the timer resets. 3 Press the PTT button to re-transmit. The time-out timer restarts and the red LED lights up. 95 English O5Head_6875947M01_C.book Page 96 Wednesday, October 20, 2010 12:13 PM

Using the Conventional Squelch Operation Features This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise. 1 Procedure:

> or < to SQL. 2 Press the Menu Select button directly below SQL. The display shows SQUELCH XX, where XX is the value for the current squelch. 3 Press the Menu Select button directly below + to increase the squelch volume. OR Press the Menu Select button directly below - to decrease the squelch volume. 4 Press H to return to the selected channel. s e r u t a e F d e c n a v d A 96 English Analog Options

Tone Private Line (PL), Digital Private-Line (DPL), and carrier squelch can be available (preprogrammed) per channel. Option Result Carrier squelch (C) You hear all traffic on a channel. The radio responds only to your messages. PL or DPL Digital Options

One or more of the following options may be preprogrammed in your radio. Consult your dealer or system administrator for more information. Option Result Digital Carrier-

You hear any digital traffic. Operated Squelch (COS) Normal Squelch You hear any digital traffic having the correct network access code. Selective Switch You hear any digital traffic having the correct network access code and correct talkgroup. O5Head_6875947M01_C.book Page 97 Wednesday, October 20, 2010 12:13 PM Using the PL Defeat Feature

This feature allows you to override any coded squelch (DPL or PL) that might be preprogrammed to a channel. The radio also unmutes to any digital activity on a digital channel. Procedure:

Place the preprogrammed PL Defeat switch in the PL Defeat position. You hear any activity on the channel. OR The radio is muted if no activity is present. Note: When this feature is active, the Carrier Squelch status indicator is displayed. Using the Digital PTT ID Feature

This feature allows you to the radio ID (number) of the radio from whom you are currently receiving a transmission. This ID, consisting up to a maximum of eight characters, can be viewed by both the receiving radio and the dispatcher. Your radios ID number is also automatically sent every time the PTT button is pressed. This is a per-channel feature. For digital voice transmissions, your radios ID is sent continuously during the voice message. Using the Smart PTT Feature (Conventional Only)

Smart PTT is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations. When smart PTT is enabled in your radio, you cannot transmit on an active channel. If you try to transmit on an active smart-PTT channel, you hear an alert tone, and the transmission is inhibited. The LED lights up solid yellow to indicate that the channel is busy. Three variations of smart PTT are available:

Mode Transmit Inhibit on Busy Channel with Carrier Transmit Inhibit on Busy Channel with Wrong Squelch Code Description You cannot transmit if any traffic is detected on the channel. You cannot transmit on an active channel with a squelch code or (if secure-

equipped) encryption key other than your own. If the PL code is the same as yours, the transmission is not prevented. A d v a n c e d F e a t u r e s Quick-Key Override This feature can work in conjunction with either of the two above variations. You can override the transmit-inhibit state by quick-keying the radio. In other words, two PTT button presses within the preprogrammed time limit. 97 English O5Head_6875947M01_C.book Page 98 Wednesday, October 20, 2010 12:13 PM

Accessing General Radio Information Your radio contains information on the following:

Radio Information IP Display Control Assignments Note:

If the feature inactivity timer is enabled, your radio automatically exits the feature when your radio is left idle long enough for the time to expire. You will hear the Menu Inactive Exit Tone upon feature exit.

Accessing Radio Information s e r u t a e F d e c n a v d A This feature displays the following information of your radio:

Host Version Secure Version CH 1 4 Version

(depending on the number of channels connected.) DSP Version KG (Secure Algorithm) Serial Number MCHIB Version CHIB Version AUX CH Version Siren Version VRS Version DVRS App Version (only when TIB Version TRC Version URC Version DVRS is available) 98 English DVRS DSP Version (only when DVRS is available) DVRS CP Version (only when DVRS is available) Serial Number Flash Size & Type RF Band Processor Version Model Number ESN Flash Code Tuning Version Note:

Procedure:

1 > or < to INFO. 2 Press the Menu Select button directly below INFO. 3 > or < to RADIO INFO and press the Menu Select button Press H at any time to return to the Home screen. directly below SEL. 4 The display shows the Information screen. 5 > or < to scroll through the various information. OR Press the Menu Select button directly below BACK to return to previous screen. OR Press H to exit and return to the home display. O5Head_6875947M01_C.book Page 99 Wednesday, October 20, 2010 12:13 PM Viewing IP Information

This feature displays the device name, IP address, and status of your radio. Note:

The device name of your radio is preprogrammed. Check with your dealer or system administrator for more information. Procedure:

Press the preprogrammed Info button and proceed to Step 3. OR Follow the procedure below. 1 > or < to INFO. 2 Press the Menu Select button directly below INFO. 3 > or < to IP INFO and press the Menu Select button directly below SEL. 4 > or < to scroll through the various information. OR Press the Menu Select button directly below BACK to return to previous screen. OR Press H to exit and return to the Home display. Viewing Control Assignments

This feature displays the programmable radio functions assigned to the controls of your radio for the currently selected channel. See Programmable Features on page 7 for more information on the various programmable features of your radio. Procedure:

1 > or < to INFO. 2 Press the Menu Select button directly below INFO. 3 > or < to CONTROL MAP and press the Menu Select button directly below SEL. A d v a n c e d F e a t u r e s 4 > or < to scroll through the various information. OR Press the Menu Select button directly below BACK to return to previous screen. OR Press H to exit and return to the Home display. 99 English Using Permanent Horn and Lights

If Permanent Horn and Lights is enabled, horn and lights will automatically be turned on when the radio powers up. Procedure:

1 Press the Menu Select button directly below H/L once to turn off the alarm(s). 2 Press the Menu Select button directly below H/L momentarily to enable the last selected alarm(s). The display briefly shows the enabled alarms, and then reverts back to the selected mode. O5Head_6875947M01_C.book Page 100 Wednesday, October 20, 2010 12:13 PM Using Optional External Alarms (Horn and Lights)

All control heads can be equipped for external alarms (horn and lights) that are activated when a Call Alert page, Private Conversation call, or phone call is received. The radio always powers up with the horn and lights feature enabled. Note:

The horn and lights feature must be enabled by a qualified radio technician. Using Non-Permanent Horn and Lights

Procedure:

1 Press the Menu Select button directly below H/L momentarily. The last selected alarm(s) are enabled, and the display shows the enabled alarm(s) alternating with the selected mode, until it is turned off. 2 Press the Menu Select button directly below H/L momentarily to turn off the alarm(s). The display shows HORN/LITES OFF. s e r u t a e F d e c n a v d A 100 English O5Head_6875947M01_C.book Page 101 Wednesday, October 20, 2010 12:13 PM Changing the Selected Alarms

Procedure:

1 Press the Menu Select button directly below H/L until the display shows the required alarm. 2 Press the Menu Select button directly below the required entry and the display exits to Home screen. Press the Menu Select button directly below the entry activates the option. Below are the selections available. Select H+L to turn on both horn and lights. The display shows HORN/LITES ON. Select LGTS to turn on the lights. The display shows LIGHTS ON. Select HORN to turn on the horn. The display shows HORN ON. An OFF entry is shown at the softkey when one of the features above is active. Selecting the OFF deactivates the current active alarm. A d v a n c e d F e a t u r e s Receiving a Call While Alarms are Turned On

When you receive a call with the Alarms turned on:

Procedure:

1 You hear the vehicles horn sounds for four seconds, and/or the car lights turn on for 60 seconds. 2 The display shows the type of call received (CALL, PAGE, or PHONE) and the selected mode name. The time interval can be modified by a qualified radio technician. Turning Off Non-Rearmable External Alarms

Procedure:

1 Press the Menu Select button directly below CALL, PAGE or PHON will turn off the external alarm(s) and place you directly in that feature. OR Press the PTT button or any control-head button to turn off the external alarm(s). 2 Press the Menu Select button directly below H/L momentarily to rearm the horn and lights feature. The Volume Knob and the DIM button have no effect on the state of the external alarm(s). 101 English O5Head_6875947M01_C.book Page 102 Wednesday, October 20, 2010 12:13 PM Turning Off Rearmable External Alarms

Procedure:

1 Press the Menu Select button directly below CALL, PAGE or PHON to turn off the external alarm(s) and place you directly in that feature. The external alarm(s) is turned off and automatically rearmed so that when you exit the entry, the external alarm(s) will automatically turn on. OR Press the PTT button or any control head button other than the Menu Select button directly below H/L to turn off the external alarm(s). The external alarm(s) is turned off and automatically rearmed so that when you exit the entry, the external alarm(s) will automatically turn on. OR Press the Menu Select button directly below H/L to turn off the external alarm(s) and exit the Horn and Lights feature. Press the Menu Select button directly below H/L momentarily to rearm the horn and lights feature. The Volume knob and the DIM button have no effect on the state of the external alarms. s e r u t a e F d e c n a v d A 102 English Using the Voice Announcement

This feature enables the radio to audibly indicate the current feature mode, Zone or Channel the user has just assigned. This audio indicator can be customized per customer requirements. This is typically useful when the user is in a difficult condition to read the content shown on the display. Each voice announcement is within a limit of three seconds maximum. The sum total duration for all voice announcements in a radio shall be no more than 1000 seconds. Note:

This feature must be preprogrammed by a qualified radio technician. The features which Voice Announcement supports are:

Zone Channel Scan Monitor Talkaround/Direct Tx Inhibit Note: Voice announcements support certain number of zone-

channel, but not all. Seek advice from your dealer or qualified technician for the best selections for this feature. O5Head_6875947M01_C.book Page 103 Wednesday, October 20, 2010 12:13 PM The two options of priority for the Voice Announcement available are:

High enables the voice of the feature to announce even when the radio is receiving calls. Low disables the voice of the feature from announcing when the radio is receiving calls. Procedure:

You hear a voice announcement when the features below are preprogrammed in the radio. The radio powers up. The radio announces the current zone and channel it is transmitting. Press the preprogrammed voice announcement button

(which specifically programmed to playback the current zone and channel). The radio announces the current zone and channel it is transmitting. Note: Pressing this preprogrammed playback button will always enable the voice feature to announce in High priority. All the three programmable buttons at the side of the radio support this feature. Change to a new zone. The radio announces the current zone and channel it is transmitting. Change to a new channel within the current zone. The radio announces the current channel. Press either the Menu Select button or preprogrammed button of the radio to launch or terminate Scan, Monitor, Talkaround/Direct or Transmit Inhibit. The radio announces the corresponding feature activation or deactivation. A d v a n c e d F e a t u r e s 103 English O5Head_6875947M01_C.book Page 104 Wednesday, October 20, 2010 12:13 PM Helpful Tips The following are suggestions to assist you in troubleshooting possible operating problems.

+ = K J E  

The cables that connect to the rear of the radio could have live voltage on some of their pins. Do not remove or reconnect these cables. Only a qualified radio technician should perform this task. Service performed by unauthorized personnel may cause the radio to transmit an emergency alarm even if the unit is turned off. If your radio is locked up or the display shows FAIL 01/09, turn the radio off and then back on. If this does not correct the condition, take the radio to a qualified radio technician for service. If radio operation is intermittent, check with other persons using the system for similar problems before taking the radio in for service. Similar problems indicate a system malfunction rather than a radio failure. If symptoms persist or, if your unit exhibits other problems, contact a qualified radio technician. s e r u t a e F d e c n a v d A 104 English O5Head_6875947M01_C.book Page 105 Wednesday, October 20, 2010 12:13 PM Accessories For a list of Motorola-approved antennas and other accessories, visit the following website:

http://www.motorola.com/governmentandenterprise On the website, search for APX Mobile Radios. You will see the accessories information besides the specifications of the radio. You can also contact your dealer for details. A c c e s s o r i e s 105 English O5Head_6875947M01_C.book Page 106 Wednesday, October 20, 2010 12:13 PM Appendix: Maritime Radio Use in the VHF Frequency Range Take a moment to review the following:

Special Channel Assignments. page 106 Operating Frequency Requirements. page 107 Special Channel Assignments Emergency Channel

If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order:

1 MAYDAY, MAYDAY, MAYDAY. 2 THIS IS _____________________, CALL SIGN __________. State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times. 3 Repeat MAYDAY and the name of the vessel. F H V e h t n i i e s U o d a R e m i t i r a M i

x d n e p p A 106 English 4 WE ARE LOCATED AT _______________________. State the position of the vessel in distress, using any information that will help responders to locate you, e.g.:

latitude and longitude bearing (state whether you are using true or magnetic north) distance to a well-known landmark vessel course, speed or destination 5 State the nature of the distress. 6 Specify what kind of assistance you need. 7 State the number of persons on board and the number needing medical attention, if any. 8 Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc. 9 OVER. 10 Wait for a response. 11 If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you. Non-Commercial Call Channel

For non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9. O5Head_6875947M01_C.book Page 107 Wednesday, October 20, 2010 12:13 PM Operating Frequency Requirements Table A-1: VHF Marine Channel List (Continued) A radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows:

on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency on ships subject to the Safety Convention, the radio must be capable of operating:

in the simplex mode on the ship station transmitting frequencies specified in the 156.025 157.425 MHz frequency band, and in the semiduplex mode on the two frequency channels specified in the table below. Note: Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast Guard. Table A-1: VHF Marine Channel List Frequency (MHz) Transmit 156.050 Receive 160.650 Channel Number 1 Channel Number 2

4 5 6 7 8 9 10 11 12 13**

14 15**

16 17**

18 19 20

22

Frequency (MHz) Transmit 156.100 156.150 156.200 156.250 156.300 156.350 156.400 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 156.850 156.900 156.950 157.000 157.050 157.100 157.150 Receive 160.700 160.750 160.800 160.850 160.950 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 156.850 161.500 161.550 161.600 161.650 161.700 161.750 A p p e n d x

i M a r i t i m e R a d o U s e i i n t h e V H F 107 English O5Head_6875947M01_C.book Page 108 Wednesday, October 20, 2010 12:13 PM Table A-1: VHF Marine Channel List (Continued) Table A-1: VHF Marine Channel List (Continued) Frequency (MHz) Transmit 157.200 157.250 157.300 157.350 157.400 156.025 156.075 156.125 156.175 156.225 156.275 156.325 156.375 156.425 156.475 156.575 156.625 156.675 156.725

156.875 Receive 161.800 161.850 161.900 161.950 162.000 160.625 160.675 160.725 160.775 160.825 160.875 160.925 156.375 156.425 156.475 156.575 156.675 156.725

Channel Number 78 79 80

84 85 86 87 88 Frequency (MHz) Transmit 156.925 156.975 157.025 157.075 157.125 157.175 157.225 157.275 157.325 157.375 157.425 Receive 161.525 161.575 161.625 161.675 161.725 161.775 161.825 161.875 161.925 161.975 162.025

* Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.

** Low power (1 W) only

*** Guard band Note: A in the Receive column indicates that the channel is transmit only. F H V e h t n i i e s U o d a R e m i t i r a M i

x d n e p p A Channel Number 24 25 26 27 28 60

62 63

65 66 67**

68 69 71 72 73 74 75 76 77**

108 English O5Head_6875947M01_C.book Page 109 Wednesday, October 20, 2010 12:13 PM Glossary This glossary is a list of specialized terms used in this manual. Term Definition ACK Active Channel A channel that has traffic on it. Acknowledgment of communication. Analog Signal ARS ASTRO 25 Trunking ASTRO Conventional Autoscan AUX CH Call Alert An RF signal that has a continuous nature rather than a pulsed or discrete nature. Automatic Registration Service Motorola standard for wireless digital trunked communications. Motorola standard for wireless digital conventional communications. A feature that allows the radio to automatically scan the members of a scan list. Auxiliary Control Head Privately page an individual by sending an audible tone. Term Definition Feature that responds to the presence of an RF carrier by opening or unmuting

(turning on) a receivers audio circuit. A squelch circuit silences the radio when no signal is being received so that the user does not have to listen to noise. A software-controlled, computer-driven device that receives and generates data for the trunked radios assigned to it. It monitors and directs the operations of the trunked repeaters. A group of characteristics such as transmit/

receive frequency pairs, radio parameters, and encryption encoding. Control Head Interface Board In a trunking system, one of the channels that is used to provide a continuous, two-

way/data communications path between the central controller and all radios on the system. Typically refers to radio-to-radio communications, sometimes through a repeater (see Trunking). A scan list that includes only conventional channels. Carrier Squelch Central Controller Channel CHIB Control Channel Conventional Conventional Scan List l G o s s a r y 109 English O5Head_6875947M01_C.book Page 110 Wednesday, October 20, 2010 12:13 PM Term CP Cursor Deadlock Digital Private Line (DPL) Digital Signal Dispatcher DSP Dynamic Regrouping ESN Definition Term Definition Codeplug A visual tracking marker (a blinking line) that indicates a location on the display. Displayed by the radio after three failed attempts to unlock the radio.The radio must be powered off and on prior to another attempt. A type of coded squelch using data bursts. Similar to PL except a digital code is used instead of a tone. An RF signal that has a pulsed, or discrete, nature, rather than a continuous nature. An individual who has radio system management duties. Digital Signal Processing A feature that allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. Electrical Serial Number A feature that allows communications to take place even though the central controller has failed. Each trunked repeater in the system transmits a data word informing every radio that the system has gone into failsoft. Federal Communications Commission. Frequency Modulation Disconnect. The first display information after the radio completes its self test. Key-variable loader: A device for loading encryption keys into the radio. Liquid crystal display Light-emitting diode A software-activated feature shown at the bottom of the display selection of these features is controlled by the g. Millennium Control Head Board Failsoft FCC FM Hang Up Home screen KVL LCD LED Menu Entry MCHB y r a s s o G l 110 English O5Head_6875947M01_C.book Page 111 Wednesday, October 20, 2010 12:13 PM Term Definition Monitor Multi-System Talkgroup Scan List Network Access Code Non-Tactical/

Revert OTAR Page Check channel activity through menu entries. If the channel is clear, you hear static. If the channel is in use, you hear conversation. It also serves as a way to check the volume level of the radio, since the radio opens the squelch when the monitor button is pressed. A scan list that can include both talkgroups

(trunked) and channels (conventional). Network Access Code (NAC) operates on digital channels to reduce voice channel interference between adjacent systems and sites. The user talks on a preprogrammed emergency channel. The emergency alarm is sent out on this same channel. Over-the-air rekeying. A one-way alert, with audio and/or display messages. A set of unique features specific to a radio. Personal Identification Number Personality PIN Preprogrammed Refers to a software feature that has been activated by a qualified radio technician. l G o s s a r y Term Private

(Conversation) Call Private Line

(PL) Programmable PTT Radio Frequency (RF) Repeater Selective Call Definition A feature that lets you have a private conversation with another radio user in the talkgroup. A sub-audible tone that is transmitted such that only receivers decoding the tone receives it. Refers to a radio control that can have a radio feature assigned to it. Push-To-Talk the PTT button engages the transmitter and puts the radio in transmit (send) operation when pressed. The part of the general frequency spectrum between the audio and infrared light regions (about 10 kHz to 10,000,000 MHz). A conventional radio feature, where you talk through a receive/transmit facility that re-transmits received signals, in order to improve communications range and coverage. A feature that allows you to call a select individual, intended to provide privacy and to eliminate the annoyance of having to listen to conversations of no interest to you. 111 English O5Head_6875947M01_C.book Page 112 Wednesday, October 20, 2010 12:13 PM Term Definition Selective Switch Squelch Standby Status Calls Tactical/

Non-Revert Talkaround Talkgroup TMS Any digital P25 traffic having the correct Network Access Code and the correct talkgroup. Special electronic circuitry, added to the receiver of a radio, that reduces, or cuts off, unwanted signals before they are heard in the speaker. An operating condition whereby the radios speaker is muted but still continues to receive data. Pre-defined text messages that allow the user to send a conditional message without talking. The user talks on the channel that was selected before the radio entered the emergency state. Bypass a repeater and talk directly to another unit for easy local unit-to-unit communications. An organization or group of radio users who communicate with each other using the same communication path. Text Messaging Service y r a s s o G l 112 English Term Trunking Trunking Priority Monitor Scan List USK UTC Zone Definition The automatic sharing of communications paths between a large number of users

(see Conventional). A scan list that includes talkgroups that are all from the same trunking system. Unique Shadow Key Coordinated Universal Time. The international time standard (formerly Greenwich Mean Time, or GMT). Zero hours UTC is midnight in Greenwich, England, which is located at 0 degrees longitude. Everything east of Greenwich

(up to 180 degrees) is later in time;

everything west is earlier. There are 42 time authorities around the world that are constantly synchronizing with each other. Abbreviated as UTC (English backronym =

Universal Time, Coordinated), it is also known as Zulu (Z) Time. A grouping of channels. O5Head_6875947M01_C.book Page 113 Wednesday, October 20, 2010 12:13 PM Commercial Warranty and Service Limited Warranty MOTOROLA COMMUNICATION PRODUCTS I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:

MOTOROLA INC. (MOTOROLA) warrants the MOTOROLA manufactured Communication Products listed below (Product) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:

APX Mobile Radio Product Accessories One (1) Year One (1) Year MOTOROLA, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA. This express limited warranty is extended by MOTOROLA to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA. MOTOROLA assumes no obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA. Unless made in a separate agreement between MOTOROLA and the original end user purchaser, MOTOROLA does not warrant the installation, maintenance or service of the Product. MOTOROLA cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA disclaims liability for range, coverage, or operation of the system as a whole under this warranty. II. GENERAL PROVISIONS:

This warranty sets forth the full extent of MOTOROLA'S responsibilities regarding the Product. Repair, replacement or refund of the purchase price, at MOTOROLAs option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR C o m m e r c i a l W a r r a n t y a n d S e r v i c e 113 English O5Head_6875947M01_C.book Page 114 Wednesday, October 20, 2010 12:13 PM INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. C)Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. III. STATE LAW RIGHTS:

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights which may vary from state to state. IV. HOW TO GET WARRANTY SERVICE:

You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA at 1-800-927-2744 US/Canada. V. WHAT THIS WARRANTY DOES NOT COVER:

A) Defects or damage resulting from use of the Product in other than its normal and customary manner. e c i v r e S d n a y t n a r r a W l a i c r e m m o C B) Defects or damage from misuse, accident, water, or neglect. 114 English D)Breakage or damage to antennas unless caused directly by defects in material workmanship. E) A Product subjected to unauthorized Product modifications, disassembles or repairs (including, without limitation, the addition to the Product of non-MOTOROLA supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA's normal warranty inspection and testing of the Product to verify any warranty claim. F) Product which has had the serial number removed or made illegible. G)Rechargeable batteries if:

any of the seals on the battery enclosure of cells are broken or show evidence of tampering. the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified. H)Freight costs to the repair depot. I) A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLAs published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA. J) Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. K) Normal and customary wear and tear. O5Head_6875947M01_C.book Page 115 Wednesday, October 20, 2010 12:13 PM VI. PATENT AND SOFTWARE PROVISIONS:

MOTOROLA will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA will pay those costs and damages finally awarded against the end user purchaser in any such suit which are attributable to any such claim, but such defense and payments are conditioned on the following:

A) that MOTOROLA will be notified promptly in writing by such purchaser of any notice of such claim;

B) that MOTOROLA will have sole control of the defense of such suit and all negotiations for its settlement or compromise; and C)should the Product or parts become, or in MOTOROLAs opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit MOTOROLA, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA. MOTOROLA will have no liability with respect to any claim of patent infringement which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA, nor will MOTOROLA have any liability for the use of ancillary equipment or software not furnished by MOTOROLA which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA certain exclusive rights for copyrighted MOTOROLA software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA software. MOTOROLA software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA software or exercise of rights in such MOTOROLA software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA patent rights or copyrights. VII. GOVERNING LAW:

This Warranty is governed by the laws of the State of Illinois, U.S.A. C o m m e r c i a l W a r r a n t y a n d S e r v i c e 115 English O5Head_6875947M01_C.book Page 116 Wednesday, October 20, 2010 12:13 PM SERVICE Proper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola to support maintenance services. Through its maintenance and installation program, Motorola makes available the finest service to those desiring reliable, continuous communications on a contract basis. For a contract service agreement, please contact your nearest Motorola service or sales representative, or an authorized Motorola dealer. Express Service Plus (ESP) is an optional extended service coverage plan, which provides for the repair of this product for a period of three years from the date of shipment from the factory, or the date of delivery if purchased from an authorized Motorola two-

way radio dealer. For more information about ESP, contact the Motorola Radio Support Center, 2204 Galvin Drive, Elgin, IL 60123, 1-800-227-6772. e c i v r e S d n a y t n a r r a W l a i c r e m m o C 116 English O5Head_6875947M01_C.book Page 119 Wednesday, October 20, 2010 12:13 PM O5Head_6875947M01_C.book Page 120 Wednesday, October 20, 2010 12:13 PM 2009, 2010 by Motorola, Inc. All Rights Reserved. 09/10 1301 E. Algonquin Rd., Schaumburg, IL 60196-1078, U.S.A. Printed in the U.S.A.

*6875947M01*

6875947M01-C