all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
USERS MANUAL | Users Manual | 2.94 MiB | ||||
1 2 | Cover Letter(s) | June 03 2008 | ||||||
1 2 | RF Exposure Info | June 03 2008 | ||||||
1 2 | RF Exposure Info | June 03 2008 | ||||||
1 2 | Test Report | June 03 2008 | ||||||
1 2 | External Photos | |||||||
1 2 | Internal Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | RF Exposure Info | |||||||
1 2 | Test Setup Photos |
1 2 | USERS MANUAL | Users Manual | 2.94 MiB |
Motorola, the Stylized M Logo, and all other trademarks indicated as such herein are Trademarks of Motorola, Inc. Reg. U.S. Pat. & Tm. Off. 2007 Motorola, Inc. All rights reserved. C O N T E N T S CONTENTS Contents. 1 Safety . 4 Introduction . 5 Package Contents. 5 Batteries and Chargers Safety Information. 7 Operational Safety Guidelines. 8 FCC Licensing Information . 9 Interference Information . 9 Radio Overview . 11 Parts of the Radio . 11 On/Off/Volume Knob. 12 Channel Selector Knob. 12 Accessory Connector . 12 Model Label . 12 Microphone . 12 Antenna. 12 LED Indicator . 12 Side Buttons . 12 The Lithium-Ion (Li-Ion) Battery . 12 Battery Features. 14 About the Li-Ion Battery . 14 Battery Recycling and Disposal . 15 Installing the Lithium-Ion (Li-Ion) Battery . 16 Removing the Lithium-Ion (Li-Ion) Battery . 16 Alkaline Battery Pack (Optional Accessory) . 17 Installing Alkaline Batteries . 17 Removing Alkaline Batteries . 17 Attaching and Removing Antenna . 18 Attaching the Antenna . 18 Removing the Antenna . 18 Installing Spring Action Belt Clip . 19 Power Supply, Adaptor and Drop-in Tray Charger . 19 Battery Life Information . 20 Alkaline Battery Life . 21 Charging the Battery . 22 1 English S T N E T N O C Getting Started . 29 Turning radio ON/OFF. 29 Adjusting Volume . 29 Selecting a Channel . 29 Talking and Monitoring . 29 Receiving a Call . 30 Talk Range . 30 Radio LED Indicators . 32 Hands-Free Use/VOX . 33 With Compatible VOX Accessories. 33 Setting VOX Sensitivity. 34 Microphone Gain. 34 Battery Save . 34 Reset to Factory Defaults . 34 End of Transmission Tone (Roger Beep Tone) . 35 Programming Features. 36 Programming Mode. 36 Learning to Read the Values the Radio Signals You . 36 Entering Programming Mode . 39 Reading Frequencies Values . 39 Reading CTCSS/DPL Values . 40 Reading Auto-Scan Values . 41 Programming Frequencies, Codes and Auto-Scan . 41 Programming Mode FAQ. 42 Programming Values Example. 43 Example of Programming a Frequency . 43 Example of Programming a Code . 44 Example of Programming Auto-Scan . 45 Other Programming Features . 46 Scan. 46 Editing Scan List . 47 Nuisance Channel Delete . 47 CPS (Computer Programming Software). 48 Bandwidth Select . 49 Time-Out Timer . 49 Power Select . 49 Battery Type Setting . 49 Call Tones . 49 Scramble L. 50 Reverse Burst . 50 Cloning Radios. 51 English 2 Cloning with a Multi Unit Charger
(MUC) . 51 Cloning Radio using the Radio to Radio (R2R) Cloning Cable
(Optional Accessory). 53 Cloning using the CPS (Computer Programming Software) . 55 Troubleshooting . 56 Use and Care . 60 Frequency and Code Charts . 61 RDX VHF Frequencies Chart . 61 RDV2020 - VHF Default Frequencies Chart . 63 Making XTN Compatible with RDX Radios - Quick Instructions . 64 RDV5100 - VHF Default Frequencies Chart . 65 RDX UHF Frequencies Chart . 66 RDU2020 - UHF Default Frequencies Chart . 70 RDU4100 - UHF Default Frequencies Chart . 71 C O N T E N T S CTCSS and PL/DPL Codes . 72 Programming Customized Frequencies on 4W/5W RDX models . 75 Motorola Limited Warranty for the United States and Canada. 76 Accessories . 80 Antennas . 80 Audio Accessories . 80 Battery . 80 Carry Accessories . 81 Power Supplies AC Pin Adaptors. 81 Software Applications. 81 Cables . 81 Chargers . 81 Power Supplies . 82 RDX Series Features Summary. 83 Programmable Buttons Chart . 92 Icons Chart . 93 3 English For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website which lists approved accessories:
http://www.motorola.com/RDX SAFETY PRODUCT SAFETY AND RF EXPOSURE COMPLIANCE
C a u t i o n Before using this product, read the operating instructions and RF energy awareness information contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION!
This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Y T E F A S English 4 INTRODUCTION Thank you for purchasing the Motorola RDX Series Radio. This radio is a product of Motorola's 75 plus years of experience as a world leader in the designing and manufacturing of communications equipment. The RDX Series radios provide cost-effective communications for businesses such as retail stores, restaurants, schools, construction sites, manufacturing, property and hotel management and more. Motorola professional two-way radios are the perfect communications solution for all of today's fast-paced industries. Note:
Read this user guide carefully to ensure you know how to properly operate the radio before use Business Radios, RPSD 1C15, Motorola 8000 West Sunrise Boulevard Plantation, Florida 33322 Radio Antenna (only for RDU4100 and RDV5100) Spring Action Belt-Clip Lithium-Ion Battery Power Supply User Guide PACKAGE CONTENTS Warranty Card Drop-in Tray Charger Product Safety & RF Exposure Booklet I N T R O D U C T O N I 5 English For a copy of a large-print version of this user guide or for product-related questions, contact:
1-800-448-6686 in the USA 1-800-461-4575 in Canada 1-866-522-5210 on your TTY (Text Telephone) For product information visit us at:
www.motorola.com/radios/business or visit our microsite at:
www.motorola.com/RDX I N O T C U D O R T N I English 6 BATTERIES AND CHARGERS SAFETY INFORMATION This document contains important safety and operating instructions. Read these instructions carefully and save them for future reference. Before using the battery charger, read all the instructions and cautionary markings on the charger, 1. 2. the battery, and the radio using the battery To reduce risk of injury, charge only the rechargeable Motorola-authorized batteries. Other batteries may explode, causing personal injury and damage. Use of accessories not recommended by Motorola may result in risk of fire, electric shock, or injury. 3. 4. 5. 6. 7. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when disconnecting the charger. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord could result in risk of fire and electric shock. If an extension cord must be used, make sure that the cord size is 18AWG for lengths up to 100 feet (30.48 m), and 16AWG for lengths up to 150 feet (45.72 m). To reduce risk of fire, electric shock, or injury, do not operate the charger if it has been broken or damaged in any way. Take it to a qualified Motorola service representative. Do not disassemble the charger; it is not repairable and replacement parts are not available. Disassembly of the charger may result in risk of electrical shock or fire. To reduce risk of electric shock, unplug the charger from the AC outlet before attempting any maintenance or cleaning S A F E T Y I N F O R M A T O N I I B A T T E R E S A N D C H A R G E R S 7 English S R E G R A H C D N A S E R E T T A B I I N O T A M R O F N I Y T E F A S Maximum ambient temperature around the power supply equipment must not exceed 40C (104F). Power output from the power supply unit must not exceed the ratings stated on the product label located at the bottom of the charger. Make sure that the cord is located where it will not be stepped on, tripped over, or subjected to water, damage, or stress. OPERATIONAL SAFETY GUIDELINES Turn the radio OFF when charging battery. The charger is not suitable for outdoor use. Use only in dry locations/conditions. Connect charger only to an appropriately fused and wired supply of the correct voltage (as specified on the product). Disconnect charger from line voltage by removing main plug. The outlet to which this equipment is connected should be nearby and easily accessible. In equipment using fuses, replacements must comply with the type and rating specified in the equipment instructions. English 8 FCC LICENSING INFORMATION INTERFERENCE INFORMATION This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. RDX Series professional two-way radios operate on radio frequencies that are regulated by the Federal Communications Commission
(FCC). To transmit on these frequencies, you are required to have a license issued by the FCC. Application is made available on FCC Form 601 and Schedules D, H, and Remittance Form 159. To obtain these FCC forms, request document 000601 which includes all forms and instructions. If you wish to have the document faxed, mailed or have questions, use the following contact information. Faxed contact the Fax-On- Demand system at:
1-202-418-0177 Mailed call the FCC forms hotline at:
Questions regarding FCC license contact the FCC at:
1-800-418-FORM 1-800-418-3676 1-888-CALL-FCC 1-888-225-5322 Or: http://www.fcc.gov I I N F O R M A T O N F C C L C E N S N G I I 9 English Replacement of any transmitter component
(crystal, semiconductor, etc.) not authorized by the FCC equipment authorization for this radio could violate FCC rules. Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited Before filling out your application, you must decide which frequency(ies) you can operate on. See Frequencies and Code Charts. For questions on determining the radio frequency, call Motorola Product Services at:
1-800-448-6686 Changes or modifications not expressly approved by Motorola may void the users authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. I I G N S N E C L C C F N O T A M R O F N I I English 10 RADIO OVERVIEW PARTS OF THE RADIO Antenna Microphone Channel Selector Knob On/Off/Volume Knob LED Indicator Accessory Connector Model Label PTT Button SB1-Monitor Button SB2- Scan/
Nuisance Channel Delete Lithium-Ion Battery I R A D O O V E R V E W I 11 English On/Off/Volume Knob Used to turn the radio ON or OFF and to adjust the radios volume. Channel Selector Knob Used to switch the radio to different channels. Accessory Connector Used to connect compatible audio accessories. Model Label Indicates the model of the radio. Microphone Speaks clearly into the microphone when sending a message. Antenna For models RDU2020, and RDV2020 the antennas are non-removable. For RDV5100, RDU4100 antennas are removable. LED Indicator Used to give battery status, power-up status, radio call information and scan status. Side Buttons Push-to-Talk (PTT) Button Press and hold down this button to talk, release it to listen. Side Button 1 (SB1) The Side Button 1 is a general button that can be configured by the Computer Programming Software - CPS. The default setting of SB1 is Monitor. Side Button 2 (SB2) The Side Button 2 is a general button that can be configured by the CPS. The SB2 default setting is Scan/Nuisance Channel Delete. The Lithium-Ion (Li-Ion) Battery RDX Series provides different types of batteries. For more information, see Battery Features on page 14. I W E V R E V O O D A R I English 12 This User Guide covers multiple RDX Series models, and may detail some features your radio does not have. The radios model is shown on the front of the radio, underneath the speaker, and provides you the following information:
Model RDV2020 RDU2020 RDU4100 RDV5100 Frequency Band Transmit Power
(Watts) Number of Channels VHF UHF UHF VHF 2 2 4 5 2 2 10 10 Antenna Non-removable Non-removable removable removable I R A D O O V E R V E W I 13 English BATTERY FEATURES RDX Series radios provide Lithium-Ion batteries that come in different capacities that will define the battery life. It also offers the option to use Alkaline batteries. About the Li-Ion Battery The RDX Series radio comes equipped with a rechargeable Li-Ion battery. This battery should be charged before initial use to ensure optimum capacity and performance. Battery life is determined by several factors. Among the more critical are the regular overcharge of batteries and the average depth of discharge with each cycle. Typically, the greater the overcharge and the deeper the average discharge, the fewer cycles a battery will last. For example, a battery which is overcharged and discharged 100% several times a day, lasts fewer cycles than a battery that receives less of an overcharge and is discharged to 50% per day. Further, a battery which receives minimal overcharging and averages only 25% discharge, lasts even longer. Motorola batteries are designed specifically to be used with a Motorola charger and vice versa. Charging in non-Motorola equipment may lead to battery damage and void the battery warranty. The battery should be at about 77F (25C) (room temperature), whenever possible. Charging a cold battery
(below 50 F [10C]) may result in leakage of electrolyte and ultimately in failure of the battery. Charging a hot battery (above 95F
[35C]) results in reduced discharge capacity, affecting the performance of the radio. Motorola rapid-rate battery chargers contain a temperature-sensing circuit to ensure that batteries are charged within the temperature limits stated above. I W E V R E V O O D A R I English 14 Battery Recycling and Disposal Li-Ion rechargeable batteries can be recycled. However, recycling facilities may not be available in all areas. Under various U.S. state laws and the laws of several other countries, batteries must be recycled and cannot be disposed of in landfills or incinerators. Contact your local waste management agency for specific requirements and information in your area. Motorola fully endorses and encourages the recycling of Li-Ion batteries. In the U.S. and Canada, Motorola participates in the nationwide Rechargeable Battery Recycling Corporation (RBRC) program for Li-Ion battery collection and recycling. Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, access RBRC's Internet web site at:
www.rbrc.com or call:
1-800-8-BATTERY This internet site and telephone number also provides other useful information concerning recycling options for consumers, businesses and governmental agencies. I R A D O O V E R V E W I 15 English Installing the Lithium-Ion (Li-Ion) Battery Removing the Lithium-Ion (Li-Ion) Battery Battery Latch Battery Latch slots 1. 2. 3. Turn OFF the radio. With the Motorola logo side up on the battery pack, fit the tabs at the bottom of the battery into the slots at the bottom of the radios body. Press the top part of the battery towards the radio until a click is heard. Note:
To learn about the Li-Ion Battery Life features, refer to About the Li-Ion Battery on page 14 1. 2. 3. Turn OFF the radio. Push down the battery latch and hold it depressed while removing the battery. Pull the battery away from the radio. I W E V R E V O O D A R I English 16 Alkaline Battery Pack (Optional Accessory) Installing Alkaline Batteries Removing Alkaline Batteries Alkaline Battery Door Alkaline Battery Door 1. 2. 3. 4. 5. Turn OFF the radio, if it is turned ON. Remove Li-Ion battery. Assemble alkaline battery pack in the same steps as installing the Li-Ion battery pack. Remove battery door from alkaline battery pack. Slide the 5 AA alkaline batteries into the frame, matching the markings inside the compartment 1. 2. 3. Turn OFF the radio, if it is turned ON. Slide the battery latches, on both sides of the battery, downwards. Pull the top of the battery away from the radios body, and lift the battery from the radios body. I R A D O O V E R V E W I 17 English Attaching and Removing Antenna These instructions apply ONLY to models RDU4100 and RDV5100. Do not attempt to remove the antenna if your radio is not one of these models. Attaching the Antenna Removing the Antenna 1. 2. Align the threaded end of the antenna with the radios antenna connector. Turn the antenna clockwise to fasten it. 1. Turn the antenna counterclockwise until you can remove it. I W E V R E V O O D A R I English 18 Installing Spring Action Belt Clip Power Supply, Adaptor and Drop-in Tray Charger Belt Clip Tab Spring Action Belt Clip 1. 2. Slide the spring action belt clip rails into the belt clip grooves on the back of the battery pack and slide it down until the belt clip tab snaps into place. To remove, pull back the metal release tab on the belt clip tab and push the spring action belt clip upward to remove. Power Supply Drop-in Tray Charger The radio is equipped with one Drop-in Tray Charger and one Power Supply with Adaptor. For details, see Chargers on page 81. I R A D O O V E R V E W I 19 English Battery Life Information When the Battery Save feature is ON (enabled by default) the battery life will be longer. The following chart summarizes battery life estimations:
Li-Ion Battery Life with Battery Save feature ON Battery Type 5 Watts 4 Watts 2 Watts Standard High Ultra High 8.5 hours 17 hours 8.5 hours 17 hours 18.5 hours 18.5 hours 12 hours 24 hours 26 hours Note:
Battery life is estimated based on 5% transmit/ 5% receive/ 90% standby standard duty cycle I W E V R E V O O D A R I English 20 Alkaline Battery Life The following chart estimates the Alkaline battery life:
Alkaline Battery Life Battery Save Feature 5 Watts 4 Watts 2 Watts ON 26 hours*
26 hours*
26 hours Notes:
Battery life are being estimated based on 5% transmit/ 5% receive/ 90% standby standard duty cycle.
* When using Alkaline battery, the radio is set to 2W by default I R A D O O V E R V E W I 21 English Charging the Battery RDX Series offers two types of chargers :
Standard Charger and, Rapid Charger. Note:
The radio comes equipped with a Standard Charger To charge the battery (with the radio attached), place it in a Motorola-approved Drop-in Tray Single Unit Charger or Drop-in Tray Multi Unit Charger. Note: When acquiring additional chargers or power supplies, make sure you have similar drop-in tray chargers and power supplies sets (all rapid or all standard). For part number details, refer to Chargers on page 81 Charging with the Drop-in Tray Single Unit Charger (SUC) Power Supply
(Transformer) Drop-in Tray Charger Port Drop-in Tray Charger 1. 2. Place the drop-in tray charger on a flat surface. Insert the connector of the power supply into the port on the side of the drop-in tray charger. Plug the AC adaptor into a power outlet. Insert the radio into the tray with the front of the radio facing the front of the charger, as shown. Note: When charging a battery attached to a radio, 3. 4. turn the radio OFF to ensure a full charge. See Operational Safety Guidelines on page 8 for more information I W E V R E V O O D A R I English 22 Charging a Standalone Battery To charge only the battery - at step 4, insert the battery into the tray, with the inside surface of the battery facing the front of the charger, as shown. Ensure the slots in the battery correctly engage in the charger Note:
Ensure that the bracket in the charger is adjusted to the correct position for either Standard or High capacity battery. See Charging a Standard Battery on page 23 Charging a Standard Battery The drop-in tray charger has a removable bracket that is adjustable depending on the type of battery that needs to be charged. It is designed to charge either the battery (with the radio) or a standalone battery. The drop-in tray charger's default position will charge a standard battery. The following image shows the orientation for each battery:
Adjustable bracket Adjustable bracket Standard High and Ultra High Capacity Figure 1: Identifying the Drop-In Chargers Position Before Charging the Battery I R A D O O V E R V E W I 23 English Charging a High Capacity or Ultra High Capacity Battery Removable Piece Removable Piece Turn around horizontal 180 degree 3. Note:
Repeat same procedure to return to the charging a Standard Battery position. Label on the removable bracket should show Standard Battery facing front. Make sure the bracket is assembled correctly for both standalone battery and battery (with radio) To convert the charger from the default setup to accommodate the High capacity or Ultra High capacity battery:
1. 2. Squeeze both tabs on each side of the removable bracket in the drop-in charger tray and lift the bracket from the charger tray. Rotate the removable bracket 180 degrees and replace it by fitting it in the charger slot until it snaps. The label on the removable bracket should show High & Ultra Capacity Battery facing front of the charger. I W E V R E V O O D A R I English 24 Drop-in Tray Charger LED Indicators Standard Charger LED Indicator Status LED Status Comments Steady red indication for 3 seconds Blinking red (slow) The charger has powered up The charger is currently charging Steady red indication Battery is fully charged Blinking red (fast) Battery had a fault when battery was inserted Power ON Charging Charging Complete Battery Fault(*) Notes:
(*) Normally re-seating the battery pack will correct this issue.
(**) Battery temperature is too warm or too cold or wrong power supply is being used I R A D O O V E R V E W I 25 English Rapid Charger LED Indicator Status LED Status Comments Power ON Steady green indication for 3 seconds Blinking green Steady green indication Charging Top-off Charging Blinking green (slow) Charge Complete Battery Fault (*) Blinking red (fast) Waiting to Charge (**) Notes:
Double-blink yellow indications The charger has powered up The charger is currently charging Battery is near fully charged Battery is fully charged Battery has a fault when battery was inserted Battery charging conditions not suitable
(*) Normally re-seating the battery pack will correct this issue.
(**) Battery temperature is too warm or too cold or wrong power supply is being used I W E V R E V O O D A R I English 26 Estimated Charging Time The following table provides the estimated charging time of the battery. For further details, see Battery on page 80. Estimated Charging Time Battery Type Standard High Capacity Ultra High Capacity 7 hours 12 hours 13 hours 1.5 hours 3 hours 3.5 hours Charging Solution Standard Charging Solution Rapid Charging Solution I R A D O O V E R V E W I 27 English Charging a Radio and Battery using a Multi Unit Charger- MUC (Optional Accessory) The Multi Unit Charger (MUC) allows drop-in charging of up to 6 radios or batteries. Batteries can be charged with the radios or removed and placed in the MUC separately. Each of the 6 charging pockets can hold a radio or battery, but not both. 1. 2. 3. 4. 5. 6. Place the charger on a flat surface. Insert the power cord plug into the MUCs jack. Plug the cord into an AC outlet. Turn the radio OFF. Set removable bracket for battery type. Insert the radio or battery into the charging pocket. Notes:
This Multi Unit Charger also allows you to clone up to 3 radios (3 Source radios and 3 Target radios). Refer to page 51 for details. Further details on MUCs operation are explained in the Instructions Sheet provided with the MUC. For part number details, refer to the Accessories section. MUC LED Indicator Status LED Status Comments Charging Steady Red Indication The charger is currently charging Charge Complete Steady Green Indication Battery is fully charged Battery Fault (*) Note:
Blinking red
(fast) Battery was faulty when inserted
(*) Normally re-seating the battery pack will correct this issue. I W E V R E V O O D A R I English 28 GETTING STARTED For the following explanations, refer to Parts of the Radio on page 11. TURNING RADIO ON/OFF To turn ON the radio, rotate the On/Off/Volume Knob clockwise. The radio will chirp and the LED Indicator will briefly blink red. To turn the radio OFF, rotate the On/Off/Volume Knob counterclockwise until you hear a click and the radio LED Indicator turns OFF. ADJUSTING VOLUME Turn the On/Off/Volume Knob clockwise to increase the volume, or counterclockwise to decrease the volume. Note:
Do not hold the radio too close to the ear when the volume is high or when adjusting the volume SELECTING A CHANNEL To select a channel, rotate the Channel Selector Knob and select the desired channel number. Program each channel separately. Each channel has its own Frequency, Interference Eliminator Code and Scan Settings. TALKING AND MONITORING It is important to monitor for traffic before transmitting to avoid talking over someone who is already transmitting To monitor, long press and hold the SB1(*) button to access channel traffic. If no activity is present, you will hear static. To release, press SB1 again. Once channel traffic has cleared, proceed with your call by pressing the PTT button. When transmitting, the LED Indicator will blink red every 3 seconds. I G E T T N G S T A R T E D 29 English TALK RANGE TALK RANGE Industrial Multi-Level Model Inside steel/concrete Industrial buildings Inside multi-level buildings UHF 4W Up to 350,000 Sq. Ft. Up to 30 Floors VHF 5W Up to 300,000 Sq. Ft. Up to 18 Floors UHF 2W Up to 250,000 Sq. Ft. Up to 20 Floors VHF 2W Up to 220,000 Sq. Ft. Up to 13 Floors D E T R A T S G N T T E G I Notes:
To listen to all activity on a current channel, short press the SB1 to set the CTCSS/DPL code to 0. This feature is called CTCSS/DPL Defeat
(Squelch set to SILENT).
(*) This assumes SB1 is not being programmed for a different mode. RECEIVING A CALL 1. Select a channel by rotating the Channel Selector Knob until you reach the desired channel. 2. 3. 4. Make sure the PTT button is released and listen for voice activity. The LED Indicator blinks red while the radio is receiving a call. To respond, hold the radio vertically 1 to 2 inches (2.5 to 5cm) from mouth. Press the PTT button to talk; release it to listen. English 30 To establish a proper two-way communication, the channel, frequency, and interference eliminator codes must be the same on both radios. This depends on the stored profile that has been preprogrammed on the radio:
1. Channel: Current channel that the radio is using, depending on radio model. 2. 3. Frequency: The frequency the radio uses to transmit/receive. Interference Eliminator Code: These codes help minimize interference by providing a choice of code combinations. 4. 5. Scramble Code: Codes that make the transmissions sound garbled to anyone listening who is not set to that specific code. Bandwidth: Some frequencies have selectable channel spacing, which must match other radios for optimum audio quality. For details on how to set up frequencies and CTCSS/DPL codes in the channels, refer to Programming Selection Mode in page 36. I G E T T N G S T A R T E D 31 English D E T R A T S G N T T E G I RADIO LED INDICATORS RADIO STATUS Channel Alias Edit Channel Busy Cloning Mode Cloning In Progress Fatal Error at Power up Low Battery Low Battery Shutdown Monitor Power-Up Idle Programming Mode /
Channel Mode Scan Mode Transmit (Tx)/Receive (RX) LED INDICATION Red heartbeat Solid orange Two orange heartbeats Solid orange One green blink, one orange blink, one green blink, then repeat for 4 seconds Orange blink Orange heartbeat LED is OFF Solid red for 2 seconds Green heartbeat Red heartbeat Red heartbeat Transmit in Low Power Select Orange heartbeat Note:
Channel Alias Edit only applies to Display Models English 32 HANDS-FREE USE/VOX VOX Accessory Accessory Port/
Connector Motorola RDX Series radios can operate hands-free (VOX) when used with compatible VOX accessories. With Compatible VOX Accessories The default factory setting for VOX sensitivity level is OFF (level 0). Before using VOX, set VOX level to a level different from 0 via the CPS. Then, perform the following steps:
1. 2. 3. 4. 5. 6. 7. Turn the radio OFF. Open accessory cover. Insert the audio accessorys plug firmly into accessory port. Turn radio ON. The LED Indicator will blink double red Lower radio volume BEFORE placing accessory near ear. To transmit, speak into accessory microphone and to receive, stop talking. VOX can be temporarily disabled by pressing the PTT button or by removing the audio accessory. Note:
To order accessories, refer to:
www.motorola.com/radios/professional, call 1 (800) 448-6686, or contact your Motorola point of purchase I G E T T N G S T A R T E D 33 English D E T R A T S G N T T E G I Setting VOX Sensitivity The sensitivity of the radio's accessory or microphone can be adjusted to suit different operating environments. VOX sensitivity can be programmed via the CPS. Default value is OFF (level 0). If you want to use the VOX feature, VOX level should be set at a level different from 0. Microphone Gain The sensitivity of the microphone can be adjusted to fit different users or operating environments. This feature can be adjusted only through the CPS. Microphone default setting is set to level 2 (medium gain). 1 = Low sensitivity 2 = Medium sensitivity 3 = High sensitivity Battery Save Battery Save feature extends battery life as your radio goes into Idle state. To enable/
disable press SB1 and SB2 buttons simultaneously for 2 or 3 seconds while powering up the radio until you hear a quick series of beeps. To have a slightly better attack time, set Battery Save feature to OFF so that the radio is always ready to transmit or receive without any delays. Note:
Reset to Factory Defaults Reset to Factory Defaults will set back all radio features to the original factory default settings. To do so, press PTT, SB2 and SB1 simultaneously while turning ON the radio until you hear a high tone chirp. Battery Save feature is set to ON by default English 34 End of Transmission Tone (Roger Beep Tone) To enable/disable End of Transmission Tone, short press the SB1 button while turning ON the radio . Note:
This setting is set to OFF by default I G E T T N G S T A R T E D 35 English I G N M M A R G O R P S E R U T A E F PROGRAMMING FEATURES To easily program all the features in your radio, it is recommended to use the CPS Programming Cable and CPS software. CPS software download is available for free at www.motorola.com/RDX PROGRAMMING MODE Programming Mode is a special radio mode to program basic radio's features by using the radios panel. When the radio is set to Programming Mode, you are able to read and modify three features:
Frequencies, Codes (CTCSS/DPL) and, Auto-Scan. The Programming Frequencies feature allows you to select frequencies for each channel. The Interference Eliminator Code (CTCSS/
DPL) helps minimize interference by providing you with a choice of code combinations that filter out static, noise, and unwanted messages. The Auto-Scan feature allows you to set a particular channel to automatically enable Scan each time you switch to that channel. Learning to Read the Values the Radio Signals You As the non-display model does not have a display to show the values that are being programmed, the radio will communicate this information using beeps and LED indications. The radio's LEDs will blink two colors:
Short and long red blinks differentiate the specific number the radio is signaling you. Please refer to Programming Mode: Reading the Values table on page 38. Orange to signal '0' and, Red for other values from '1' to '9'. English 36 Enter Programming Mode
(PTT + SB1 + Turn ON radio) 1 PROGRAMMING MODE 2 Frequencies CTCSS/DPL PTT First Digit Second Digit PTT First Digit PTT Second Digit PTT Third Digit PTT Long PTT Long PTT Idle Programming Mode PTT Roll Over key chirp 3 Auto - Scan PTT ON /
OFF F E A T U R E S P R O G R A M M N G I Exit Long PTT Figure 1: Entering Programming Mode 37 English Programming Mode: Reading the Values Number Confirmation Beep LED Indication 0 1 2 3 4 5 6 7 8 9 Zero beep One beep Two beeps Three beeps Four beeps Long beep Long beep and one beep Long beep and two beeps Long beep and three beeps Long beep and four beeps One orange blink One short red blink Two short red blinks Three short red blinks Four short red blinks One long red blink One long and one short red blinks One long and two short red blinks One long and three short red blinks One long and four short red blinks I G N M M A R G O R P S E R U T A E F English 38 Entering Programming Mode Note:
Before programming the features, make sure your radio is set to the channel you wish to program. You can do so before entering Programming Mode or at any time during the Programming Mode by turning the Channel Selector Knob to the desired channel To read or modify Frequencies, Codes and Auto-Scan, set the radio to 'Programming Mode' by long pressing both the PTT and the SB1 button simultaneously while turning ON the radio for 3 to 5 seconds until a chirp sounds to indicate that you have entered 'Idle'
Programming Mode (*).The LED Indicator will start blinking a green heartbeat. Note:
(*)'Idle' Programming Mode is the stage of the Programming Mode in which the radio is waiting for the user to start the radio programming cycle (refer Entering Programming Mode on page 37) Once you are in the 'Idle' Programming Mode, you will be able to read the Frequencies, Codes and Auto-Scan setting by short pressing the PTT button to move along the different programmable features. Reading Frequencies Values When reading frequencies values you need to read two digits as RDX Series radios have 27 frequencies for VHF and 89 frequencies for UHF. Once in Idle Programming Mode, the radio will signal the first value it was programmed when you short press the PTT button (see Figure 2:
Reading Frequencies Values on page 40). This value corresponds to the frequency's first digit F E A T U R E S P R O G R A M M N G I 39 English I G N M M A R G O R P S E R U T A E F value. If you short press the PTT button again, the radio will signal you the second digit value. 1 Frequencies PROGRAMMING M 2 CTCSS PTT First Digit Second Digit PTT First Digit PTT Long PTT Long PTT You will have to read three digits as RDX Series have up to 122 codes available (refer to Frequencies and Codes Charts Section). The following is an example of the order in which your radio will be signaling the 118 CTCSS/DPL code:
Mode Idle Programming PTT Figure 2: Reading Frequencies Values Reading CTCSS/DPL Values If you continue short pressing the PTT button as shown in Figure 1: Entering Programming Mode on page 37 (stage 2), the radio will move forward to programming CTCSS/PL Codes. When reading the values for CTCSS/PL Codes the radio signals you the digit codes each time you short press the PTT button. Figure 3: Example of How to Program Values Short press the PTT button. The radio will signal you the first digit 1. Short press PTT button again and the radio will show the second digit 1 and, Finally, short press PTT again and radio will show the third digit 8. English 40 Reading Auto-Scan Values After reading the CTCSS/DPL codes, short press the PTT button and the radio will take you to Auto-Scan (refer to Stage 3 of Figure 3:
Entering Programming Mode on page 40). Auto-Scan only has two values:
If the radio signals the value... It means Auto-
Scan is... 0 1 OFF ON Auto-Scan is set to OFF by default. Note: While in Auto-Scan Mode, if you short press PTT button, the radio will return to the Idle Programming Mode. It will then generate a roll-over chirp and it will start blinking a green heartbeat Programming Frequencies, Codes and Auto-Scan Each time your radio signals and beeps the current setting you can change this setting by either increasing it by short pressing SB1 or decreasing it by short pressing SB2 . The radio will then signal the new setting it has been programmed. Saving Settings If you are satisfied with the setting, you can either:
short press PTT to continue programming, long press PTT to save and return to 'Idle'
Programming Mode, or long press the PTT button twice to exit 'Idle'
Programming Mode and return to the normal radio operation. Note:
If you do not wish to save the value you just programmed, turn radio OFF or change channel using the channel knob. F E A T U R E S P R O G R A M M N G I 41 English If you roll-over to the beginning at Idle Programming Mode you will hear a chirp and the LED Indicator will start blinking green again. All values that were changed will be automatically saved. Programming Mode FAQ 1. I got distracted while programming and forgot which digit I was programming. What should I do?
Return to 'Idle' Programming Mode and start over, as you will not be able to return to the Programming Mode (the radio does not provide further way to let you know the specific stage you are at when programming). Therefore you can:
Long press the PTT button. The radio will return to the 'Idle' Programming Mode or, Turn OFF the radio and enter Programming Mode again (see instructions in the beginning of this section) 2. I am trying to program a frequency (or code) value but the radio would not do it. It rolled over and took me back to value 0. The radio will not allow you to program any values that are not available in the frequencies and codes pool. For example, if you try to program code 128, the radio would not accept it, as the maximum value allowed is 122. Same thing will happen with frequencies. Check the Frequencies and Codes Charts section to make sure you are programming a valid number. 3. I am trying to enter the Programming Mode but the radio would not do it. The radio might be locked using the CPS to not allow Front Panel Programming. To re-enable, use the CPS. I G N M M A R G O R P S E R U T A E F English 42 4. When I was programming I made a mistake and programmed the wrong value. How can I erase it or re-program it?
If you make a mistake while programming a value you have two choices:
The radio roll-over (and generates a 'wrap-
around' sound) each time it reaches a maximum
(9) or minimum (0) value. Keep increasing (short press SB1) or decreasing (short pressing SB2) until you get the desired value or, Turn OFF the radio and start-over. I just programmed the value I wanted. How do I exit Programming Mode?
If you are in Programming Mode you can exit by long pressing the PTT button twice. If you are already in the Idle Programming Mode, long press the PTT button once. 5. 6. I am done programming the features in this channel and want to program another channel. Switch to the new channel you wish to program by using the Channel Selector Knob. The radio will enter 'Idle' Programming Mode. If you wish to save the changes, make sure you are in the Idle Programming Mode before switching the channel as otherwise you will lose the changes made. PROGRAMMING VALUES EXAMPLE Example of Programming a Frequency Assuming current frequency value is set to Channel 1, with the UHF default frequency 02
(equivalent to 464.5500 MHz), and you want to change it to Frequency Number = 13 (which is mapped to 461.1375 MHz), follow this sequence:
Enter Programming Mode F E A T U R E S P R O G R A M M N G I 43 English Short press the PTT button to enter Frequency Mode. Radio will signal current value 0 (orange blink) Press the SB1 button once to increase first digit to 1. Short press the PTT button once to move ahead and program the frequencys second digit. Radio will signal current value which is 2 (two red blinks). Press the SB1 button to increase the digit value to 3. Long press the PTT button. LED Indicator will show a green heartbeat to indicate 'Idle' state. Long press the PTT button to exit Programming Mode or turn radio OFF. Example of Programming a Code Assuming current code value is set to factory default 001, and you want to change it to CTCSS/DPL Code = 103 follow the sequence below:
Enter Programming Mode Short press the PTT button three times (Enter CTCSS/DPL Programming Selection Mode). The LED Indicator will blink orange to indicate that current value is 0 Press the SB1 button once (to change first digit to 1) LED Indicator will blink red. Short press the PTT button (to move forward and program second digit). The LED Indicator will blink orange to indicate current value is 0. I G N M M A R G O R P S E R U T A E F English 44 Short press the PTT button and move ahead to program the third digit. LED Indicator will blink red to indicate current value is 1. Press the SB1 button to change the third digit to 2. Press the SB1 button to change again this third digit to 3. Radio will signal the chosen value. Long press the PTT button to save changes and return to 'Idle' Programming Mode. Once in 'Idle' Programming Mode, LED Indicator will start blinking a green heartbeat. Long press the PTT button to exit Programming Mode. Example of Programming Auto-Scan Auto-Scan is the last Programming Mode and can be set to either ON or OFF on a particular channel. To set Auto-Scan to ON:
Enter Programming Mode and select the desired channel (see Figure 1: Entering Programming Mode on page 37). Short press the PTT button six times to enter Auto-Scan Programming Selection Mode. The radio will signal beeps and will show the current Auto-Scan setting (please refer to Reading Auto-
scan Settings on page 41). Short press the SB1 button to toggle ON/OFF the Auto-Scan feature in the channel. When ON, the LED Indicator will blink RED once. When OFF, the LED Indicator will blink ORANGE once. F E A T U R E S P R O G R A M M N G I 45 English I G N M M A R G O R P S E R U T A E F which was selected before Scan was activated. If no transmission occurs within five seconds, scanning will resume. If you want to scan a channel without Interference Eliminator Codes (CTCSS/DPL), set the code settings for the channels to 0 in the CTCSS/DPL Programming Selection Mode. Whenever the radio is set up in Scan, the LED Indicator will signal a red blink. Note:
(*)Assumes the SB2 button is not programmed to other function different from the default. If Auto-Scan has been enabled for a particular channel, do not press SB2 to scan the channel, as the radio will do it automatically. OTHER PROGRAMMING FEATURES Scan Scan allows you to monitor other channels to detect conversations. When the radio detects a transmission, it will stop scanning and will stop on the active channel. This will allow you to listen and talk to people on that channel without having to change the channel knob. If there is talking on Channel 2 during this time, the radio will stay on Channel 1 and you will not hear Channel 2. After talking has stopped in Channel 1, the radio waits for 5 seconds before resuming scan again. To start scanning, press the SB2 button (*). When the radio detects channel activity, it will stops on that channel until the activity ends. You can talk to the person(s) transmitting without having to switch channels by pressing PTT. To stop scanning, short press the SB2 button again. By pressing the PTT button while the radio is scanning, the radio will transmit on the channel English 46 Editing Scan List Scan Lists can be edited by using the CPS
(refer to CPS section on page 48) Nuisance Channel Delete Nuisance Channel Delete allows you to temporarily remove channels from the Scan List. This feature is useful when irrelevant conversations on a nuisance channel tie up the radio's scanning feature. To delete a channel from the Scan List:
Wait until the radio stops on the channel you wish Start Scan by short pressing the SB2 button (*) to eliminate, then long press the SB2 button to delete it. The channel will not be removed until you exit Scan by short pressing the SB2 button again or by turning the radio OFF. Note:
(*) Assumes the SB2 button is not programmed to another function different from the default. F E A T U R E S P R O G R A M M N G I 47 English CPS (COMPUTER PROGRAMMING SOFTWARE) Radio to be programmed USB Connector C P S S o f t w a r e Drop-in Charger Tray Mini Connector CPS Programming Cable The easiest way to program or change features in your radio is by using the Computer Programming Software (CPS) and the CPS Programming Cable(*). CPS Software is available for free as web based downloadable software at:
www.motorola.com/RDX I G N M M A R G O R P S E R U T A E F To program, connect the RDX Series radio via the Drop-in Charger Tray and CPS Programming Cable as shown in the picture above. CPS allows the user to program frequencies, PL/DPL codes, as well as other features such as: Bandwidth Select, Time-out Timer, Power Select, Battery Type Select, Scan List, Call Tones, Scramble, Reverse Burst, etc. CPS is a very useful tool as it can also lock the Front-
Panel Radio Programming or restrict any specific radio feature to be changed (to avoid accidentally erasing the preset radio values). It also provides security by giving the option to set up a password for profile radio's management. Please refer to Features Summary Chart Section at the end of the user guide for more details. Note:
(*) CPS Programming Cable (P/N RKN4155) is an accessory sold separately. Please contact your Motorola point of purchase for more information. English 48 Note:
Some frequencies may have FCC transmit power restrictions that do not allow them to be set at a higher power level. For details see the Frequencies and Code Chart Section. Battery Type Setting The RDX Series radio can be powered by either Alkaline or Lithium-Ion batteries. Call Tones Call Tones feature allows you to transmit to other radios in your group by alerting them that you are about to talk or alerting them without speaking. Bandwidth Select Default setting for Bandwidth Select depends on the specific frequency and channel. Some frequencies have selectable channel spacing, which must match with other radios for optimum audio quality. For details, refer to Frequency and Code Charts section. Time-Out Timer When pressing the PTT button, transmissions can be terminated by setting up a 'time-out timer. Power Select Power Select allows you to select between high and low transmission power per frequency in each channel. The power levels for RDX Series 2W toggle between 1W and 2W or 2W and 4W/5W depends on the model. F E A T U R E S P R O G R A M M N G I 49 English Notes:
The features described in previous pages are just some of the features CPS has. CPS offers more capabilities. For more information refer to the HELP file in the CPS. Some of the features available with the CPS software may vary depending on the radio model. Scramble L The Scramble feature makes transmissions sound garbled to anyone listening without the same code. Scramble default value is OFF. Reverse Burst Reverse Burst eliminates unwanted noise
(squelch tail) during loss of carrier detection. You can select values of either 180/240. I G N M M A R G O R P S E R U T A E F English 50 CLONING RADIOS You can clone RDX Series radio profiles from one Source radio to a Target radio by using any one of these 3 methods:
a Multi Unit Charger (optional accessory), Two Single Unit Chargers (SUC) and a Radio-to-
Radio cloning cable (optional accessory), the CPS (free software download) Cloning with a Multi Unit Charger (MUC) or copied from) and a Target radio (the radio which profile will be cloned from the source radio.) The Source radio has to be in Pocket 1, 3 or 5 while the Target radio has to be in Pocket 2, 4 or 6, matching in the MUCs pockets by pairs as follows:
1 and 2 or, 3 and 4 or, 5 and 6 (*). When cloning, the MUC does not need to be plugged into a power source, but ALL radios require charged batteries. 1. Turn ON the Target radio and place it into one of the MUC Target Pockets Power the Source radio following the sequence below:
2. F E A T U R E S P R O G R A M M N G I To clone radios using the MUC, there must be at least two radios:
a Source radio (radio which profiles will be cloned Long press the PTT button and SB2 simultaneously while turning the radio ON. 51 English Further details on how to clone radios are explained in the Instructions Sheet provided with the MUC. When ordering the MUC, please refer to P/N RLN6309. Notes:
Paired Target radios and Source radios must be of the same band type in order for the cloning to run successfully.
(*) MUC pockets numbers should be read from left to right with the Motorola logo facing front. Wait for 3 seconds before releasing the buttons until a distinctive audible tone is heard. Place the Source radio in the source pocket that pairs with the target pocket you chose in step 1. Press and release SB1. After cloning is completed, the Source radio will sound either a pass tone (cloning was successful) or a fail tone (cloning process has failed). The pass tone sounds like a good key chirp whereas the fail tone sounds similar to a bonk tone. If the Source radio is a display model, it will either show Pass or Fail on the display (a tone will be heard within 5 seconds). Once you have completed the cloning process, turn the radios OFF and ON to exit the cloning mode. If cloning fails please refer to What To Do if Cloning Fails on page 54. 3. 4. 5. I G N M M A R G O R P S E R U T A E F English 52 Cloning Radio using the Radio to Radio
(R2R) Cloning Cable (Optional Accessory) Operating Instructions 1. Before beginning the cloning process, make sure you have:
A fully charged battery on each one of the radios. Two Single Unit Chargers (SUC). Turned OFF the radios and, Both radios are of the same radio model. 2. 3. Note:
Unplug any cables (power supply or USB cables) from the SUCs. Plug one side of the cloning cable mini connector to one SUC. Plug the other end to the second SUC. During the cloning process no power is being applied to the SUC. The batteries will not be charged. A data communication is being established between the two radios. 4. 5. Turn ON the Target radio and place it into one of the SUCs. On the Source radio, power the radio following the sequence below:
Long press the PTT button and SB2 simultaneously while turning the radio ON. Wait for 3 seconds before releasing the buttons until a distinctive audible tone is heard. 6. Place the Source radio in its SUC, press and release SB1. F E A T U R E S P R O G R A M M N G I 53 English I G N M M A R G O R P S E R U T A E F 7. 8. After cloning is completed, the Source radio will sound either a pass tone (cloning was successful) or a fail tone (cloning process has failed). The pass tone sounds like a good key chirp whereas the fail tone sounds similar to a bonk tone. If the Source radio is a display model, it will either show Pass or Fail on the display (a tone will be heard within 5 seconds). Once you have completed the cloning process, turn the radios OFF and ON to exit clone mode. What To Do if Cloning Fails The radio will emit an audible bonk indicating that the cloning process has failed. In the event that cloning fails, try performing each of the following before trying to start the cloning process again:
1. Ensure that the batteries on both radios are fully charged. Check the cloning cable connection on both SUCs. 2. 3. 4. 5. 6. 7. Ensure that the battery is engaged properly on to the radio. Ensure that there is no debris in the charging tray or on the radio contacts. Ensure that the Source radio is in cloning mode. Ensure that the Target radio is turned ON. Ensure that radios are both from the same type
(same frequency band, same front panel
(display/non display), same region and same transmission power). Note:
This cloning cable is designed to operate only with compatible Motorola RLN6175
(Standard) and RLN6304 (Rapid) Single Unit Chargers. When ordering Cloning Cable please refer to P/
N RLN6303. For details about accessories refer to Accessories section. English 54 Cloning using the CPS (Computer Programming Software) When cloning using this method, you will need to have the CPS software, a Drop-in Tray Charger and the CPS Programming Cable. To order the CPS Programming Cable, please refer to P/N RKN4155. Information on how to clone using the CPS is available either in:
the CPS Help File --> Content and Index -->
Cloning Radios, or in the CPS Programming Cable Accessory Leaflet. F E A T U R E S P R O G R A M M N G I 55 English TROUBLESHOOTING Symptom No Power Hearing other noises or conversation on a channel Try This... Recharge or replace the Li-Ion battery. Reposition or replace AA batteries. Extreme operating temperatures may affect battery life. Refer to See About the Li-Ion Battery on page 14. Confirm Interference Eliminator Code is set. Frequency or Interference Eliminator Code may be in use. Change settings: either change frequencies or codes on all radios. Make sure radio is at the right frequency and code when transmitting. Refer to Talking and Monitoring on page 29 Message Scrambled Scramble Code might be ON, and/or setting does not match the other radios'
settings. Audio quality not good enough Radio settings might not be matching up correctly. Double check frequencies, codes and bandwidths to make sure they are identical in all radios I G N T O O H S E L B U O R T English 56 Symptom Try This... Limited talk range Message not transmitted or received Steel and/or concrete structures, heavy foliage, buildings or vehicles decrease range. Check for clear line of sight to improve transmission. Wearing radio close to body such as in a pocket or on a belt decreases range. Change location of radio. To increase range and coverage, you can either reduce obstructions, increase power, or use UHF radio instead of VHF radio. UHF radios provide greater coverage in industrial and commercial buildings. VHF is designed for outdoor or smaller or wood structures. Increasing power provides greater signal range and increased penetration through obstructions. Refer to See Talking and Monitoring on page 29. Make sure the PTT button is completely pressed when transmitting. Confirm that the radios have the same Channel, Frequency, Interference Eliminator Code and Scramble Code settings. Refer to Talking and Monitoring section on page 29 for further information. Recharge, replace and/or reposition batteries. Refer to About your Li-Ion Battery section on page 14. Obstructions and operating indoors, or in vehicles, may interfere. Change location. Refer to Talking and Monitoring Section on page 29. Verify that the radio is not in Scan. Refer to Scan on page 46 and Nuisance Channel Delete on page 47. T R O U B L E S H O O T N G I 57 English Symptom Try This... Heavy static or interference Radios are too close; they must be at least five feet apart. Radios are too far apart or obstacles are interfering with transmission. Refer to Talking and Monitoring on page 29. Low batteries Recharge or replace Li-Ion battery. Replace AA batteries. Extreme operating temperatures affect battery life. Refer to About the Li-Ion Battery on page 14. Drop-in Charger LED light does not blink Low battery indicator is blinking although new batteries are inserted Check that the radio/battery is properly inserted and check the battery/charger contacts to ensure that they are clean and charging pin is inserted correctly. Refer to Charging the Battery section on page 22, Drop-in Tray Charger LED Indicators section on page 25 and Installing the Lithium-Ion Battery section on page 16. Verify that the radio is set to the correct battery type. Refer to Installing the Li-Ion Battery section on page 16, Installing Alkaline Batteries section on page 17 and About your Li-Ion Battery section on page 14. I G N T O O H S E L B U O R T English 58 Symptom Try This... Cannot activate VOX Battery does not charge although it has been placed in the drop-in charger for a while VOX feature might be set to OFF. Use the CPS to ensure that the VOX Sensitivity level is not set to 0. Accessory not working or not compatible. Refer to Hands-Free Use/VOX section on page 33. Check drop-in tray charger is properly connected and correspond to a compatible power supply. Ensure that you have the drop-in tray charger adjustable piece placed on the right position. Refer to Charging with the Drop-In Tray Single Unit Charger section on page 22 and Charging a Standalone Battery section on page 23. Check the chargers LEDs indicators to see if the battery has a problem. Refer to Drop-in Tray Charger LED Indicators section on page 25. Note: Whenever a feature in the radio seems to not correspond to the default or preprogrammed values, check to see if the radio has been programmed using the CPS with a customized profile. T R O U B L E S H O O T N G I 59 English USE AND CARE E R A C D N A E S U Use a soft damp cloth to clean the exterior Do not immerse in water Do not use alcohol or cleaning solutions If the radio is submerged in water... Turn radio OFF and remove batteries Dry with soft cloth Do not use radio until completely dry English 60 FREQUENCY AND CODE CHARTS RDX VHF FREQUENCIES CHART The charts in this section provide Frequency and Code information. These charts are useful when using Motorola RDX Series two-way radios with other business radios. Most of the frequencys positions are the same as Spirit M, GT, S, and XTN Series Frequencies. RDX VHF Frequencies Frequency # Frequency Frequency # Frequency
(MHz) 151.6250 151.9550 152.8850 152.9150 151.7000 151.7600 152.9450 151.8350 151.8050 151.5125 Bandwidth 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 12.5 kHz 12.5 kHz 12.5/25.0 kHz 12.5/25.0 kHz 12.5/25.0 kHz 12.5 kHz 1 2 3 4 5 6
*7
*8
*9 10
(MHz) 151.6550 151.6850 151.7150 151.7450 151.7750 151.8650 151.8950 151.9250 152.7000 154.4900 Bandwidth 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 11 12 13 14 15 16 17 18 19 20 F R E Q U E N C Y A N D C O D E 61 English RDX VHF Frequencies (cont.) Frequency # Frequency Frequency # Frequency
(MHz) 154.5150 154.5275 154.5400 153.0050 Bandwidth 25.0 kHz 12.5 kHz 25.0 kHz 25.0 kHz 21 22 23 24 Notes:
(MHz) 154.6550 158.4000 158.4075 Bandwidth 25.0 kHz 25.0 kHz 12.5 kHz 25 26 27
() Bandwidth for frequencies 10, 22 and 27 are not selectable and different from XTN. You might notice the communication quality differences when using these frequencies to interoperate with XTN radios.
(*) Due to FCC regulations these frequencies (six in total) are different from the previous Motorola Legacy Series radios. This means that if you select the RDX radio in one of these frequencies the radio will not inter-operate with an XTN radio. In order for a RDX radio to inter-operate with an XTN radio, make sure you choose any of the frequencies (21 in total) that are common for both radios. E D O C D N A Y C N E U Q E R F English 62 RDV2020 - VHF DEFAULT FREQUENCIES CHART The following are the default frequencies programmed in your RDX Radio. Note that the VHF default frequencies programmed in channels 1 and 2 are different from the XTN Series default values. In order for a RDX radio to inter-operate with an XTN radio, you must make sure you choose any of the frequencies (21 in total, read User Guide for details) that are common for both radios. BRUS RDX VHF 2CH Radios Default Frequencies - RDV2020 Channel Frequency #
1 2 20 21 Frequency
(MHz) 154.4900 154.5150 Note:
For RDV2020, refer to Channel # 1 and # 2. Code #
Code Bandwidth 1 1 67.0 Hz 67.0 Hz 25.0 kHz 25.0 kHz F R E Q U E N C Y A N D C O D E 63 English MAKING XTN COMPATIBLE WITH RDX RADIOS - QUICK INSTRUCTIONS The following instructions are a quick and easy way to make your XTN (XV1100, XV2100 and XV2600 models) compatible with RDX Series default frequencies:
1. Make sure your XTN is programmed to the factory default frequencies (Turn your radio ON while holding the MENU and PTT buttons simultaneously for three seconds). Program Channel 1 with Frequency # 20 (154.4900 Mhz) and Channel 2 (for models XV2100 and XV2600 only) with Frequency # 21 (154.5150 Mhz). 2. E D O C D N A Y C N E U Q E R F English 64 XTN VHF Default Frequencies Channel Frequency #
1 2 3 4 5 6
**3
**4 1 2 10 12 Frequency
(Mhz) 154.5700 154.6000 151.6250 151.9550 151.5125 151.6850 Code Bandwidth 67.0 Hz 67.0 Hz 67.0 Hz 67.0 Hz 67.0 Hz 67.0 Hz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz Due to FCC regulations, the highlighted frequencies are different from the XTN default values. Make sure to choose a compatible frequency whenever you need to interoperate with XTN series.
(**) Former XTN frequencies # 3 (154.5700 MHz) and # 4 (154.6000 MHz) are considered MURS frequencies and are not available in the RDX Series. RDV5100 - VHF DEFAULT FREQUENCIES CHART Default frequencies for the RDV5100 are fully compatible with the AXV5100 radios (AX Series). If you need to make this radio compatible with XTN series, please re-program RDV5100 frequencies to match XTN frequencies defaults. RDX VHF 10CH Radios Default Frequencies - RDV5100 Channel Frequency #
1 2 3 4 5 6 7 8 9 10 1 1 1 1 1 2 2 2 2 2 Frequency
(MHz) 151.6250 151.6250 151.6250 151.6250 151.6250 151.9550 151.9550 151.9550 151.9550 151.9550 Code #
Code Bandwidth 1 4 8 29 0 1 6 10 29 0 67.0 Hz 77.0 Hz 88.5 Hz 179.9 Hz
67.0 Hz 82.5 Hz 94.8 Hz 179.9 Hz
25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz Note:
Compatible with AXV5100 radios (AX series) F R E Q U E N C Y A N D C O D E 65 English RDX UHF FREQUENCIES CHART RDX UHF Frequencies (cont.) Frequency # Frequency
(MHz) 464.5000 464.5500 467.7625 467.8125 467.8500 467.8750 467.9000 467.9250 461.0375 461.0625 461.0875 461.1125 461.1375 1 2
*3
*4
*5
*6
*7
*8 9 10 11 12 13 Bandwidth 12.5/25.0 kHz 12.5/25.0 kHz 12.5 kHz 12.5 kHz 12.5/25.0 kHz 12.5/25.0 kHz 12.5/25.0 kHz 12.5/25.0 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz Frequency # Frequency
(MHz) 461.1625 461.1875 461.2125 461.2375 461.2625 461.2875 461.3125 461.3375 461.3625 462.7625 462.7875 462.8125 462.8375 14 15 16 17 18 19 20 21 22
*23
*24
*25
*26 Bandwidth 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz E D O C D N A Y C N E U Q E R F English 66 RDX UHF Frequencies (cont.) Frequency # Frequency
(MHz) 462.8625 462.8875 462.9125 464.4875 464.5125 464.5375 464.5625 466.0375 466.0625 466.0875 466.1125
*27
*28
*29 30 31 32 33 34 35 36 37 Bandwidth 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz Frequency # Frequency
(MHz) 466.1375 466.1625 466.1875 466.2125 466.2375 466.2625 466.2875 466.3125 466.3375 466.3625 467.7875 38 39 40 41 42 43 44 45 46 47
*48 Bandwidth 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz F R E Q U E N C Y A N D C O D E 67 English RDX UHF Frequencies (cont.) Frequency # Frequency
(MHz) 467.8375 467.8625 467.8875 467.9125 469.4875 469.5125 469.5375 469.5625 462.1875 462.4625 462.4875 462.5125
*49
*50
*51
*52 53 54 55 56 57 58 59 60 Bandwidth 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz Frequency # Frequency
(MHz) 467.1875 467.4625 467.4875 467.5125 451.1875 451.2375 451.2875 451.3375 451.4375 451.5375 451.6375 452.3125 61 62 63 64 65 66 67 68 69 70 71 72 Bandwidth 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz E D O C D N A Y C N E U Q E R F English 68 RDX UHF Frequencies (cont.) Frequency # Frequency
(MHz) 452.5375 452.4125 452.5125 452.7625 452.8625 456.1875 456.2375 456.2875 456.3375 73 74 75 76 77 78 79 80 81 Bandwidth 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz Notes:
Frequency # Frequency
(MHz) 456.4375 456.5375 456.6375 457.3125 457.4125 457.5125 457.7625 457.8625 82 83 84 85 86 87 88 89
Bandwidth 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz 12.5 kHz
(*) Frequency limited to 2W maximum power output When referring to XTN radios, note that frequencies from # 57 to # 89 are 33 new additional frequencies F R E Q U E N C Y A N D C O D E 69 English RDU2020 - UHF DEFAULT FREQUENCIES CHART RDX UHF 2CH Radios Default Frequencies - RDU2020 Channel Frequency #
1 2 2 8 Frequency
(MHz) 464.5500 467.9250 Code #
Code Bandwidth 1 1 67.0 Hz 67.0 Hz 25.0 kHz 25.0 kHz Note:
Compatible with XTN series radios E D O C D N A Y C N E U Q E R F English 70 RDU4100 - UHF DEFAULT FREQUENCIES CHART Default frequencies for the RDU4100 are fully compatible with the AXU4100 radios (AX Series). If you need to make this radio compatible with XTN series, please re-program RDU4100 frequencies to match XTN UHF frequencies defaults. RDX UHF 10 CH Radios Default Frequencies - RDU4100 Channel Frequency #
1 2 3 4 5 6 7 8 9 10 1 1 1 1 1 2 2 2 2 2 Frequency
(MHz) 464.5000 464.5000 464.5000 464.5000 464.5000 464.5500 464.5500 464.5500 464.5500 464.5500 Code #
Code Bandwidth 1 4 8 29 0 1 6 10 29 0 67.0 Hz 77.0 Hz 88.5 Hz 179.9 Hz
67.0 Hz 82.5 Hz 94.8 Hz 179.9 Hz
25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz 25.0 kHz F R E Q U E N C Y A N D C O D E Note:
Compatible with AXU4100 radios series (AX series) 71 English CTCSS AND PL/DPL CODES CTCSS 1 2 3 4 5 6 7 8 9 10 11 12 13 Hz 67.0 71.9 74.4 77.0 79.7 82.5 85.4 88.5 91.5 94.8 97.4 100.0 103.5 Note:
(*) New CTCSS code. CTCSS CTCSS Codes Hz 107.2 110.9 114.8 118.8 123 127.3 131.8 136.5 141.3 146.2 151.4 156.7 162.2 14 15 16 17 18 19 20 21 22 23 24 25 26 CTCSS 27 28 29 30 31 32 33 34 35 36 37 38 122 (*) Hz 167.9 173.8 179.9 186.2 192.8 203.5 210.7 218.1 225.7 233.6 241.8 250.3 69.3 E D O C D N A Y C N E U Q E R F English 72 DPL 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 Code 23 25 26 31 32 43 47 51 54 65 71 72 73 74 114 115 PL/DPL Codes (cont.) DPL 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 Code 116 125 131 132 134 143 152 155 156 162 165 172 174 205 223 226 DPL 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 Code 243 244 245 251 261 263 265 271 306 311 315 331 343 346 351 364 F R E Q U E N C Y A N D C O D E 73 English DPL 87 88 89 90 91 92 93 94 95 96 97 98 Code 365 371 411 412 413 423 431 432 445 464 465 466 PL/DPL Codes (cont.) DPL 99 100 101 102 103 104 105 106 107 108 109 110 Code 503 506 516 532 546 565 606 612 624 627 631 632 DPL 111 112 113 114 115 116 117 118 119 120 121 Code 654 662 664 703 712 723 731 732 734 743 754 E D O C D N A Y C N E U Q E R F English 74 PROGRAMMING CUSTOMIZED FREQUENCIES ON 4W/5W RDX MODELS Certain 4W/5W Models can be programmed to have customized frequencies (different from the ones shown in the VHF and UHF charts in previous pages). VHF range is 146 -174 MHz and UHF 438 - 470 MHz. Certain 4W/5W models can also be programmed to work with repeaters. Please contact your Motorola point of purchase for details. F R E Q U E N C Y A N D C O D E 75 English MOTOROLA LIMITED WARRANTY FOR THE UNITED STATES AND CANADA What Does this Warranty Cover?
Subject to the exclusions contained below, Motorola, Inc. warrants its telephones, pagers, and consumer and business two-way radios (excluding commercial, government or industrial radios) that operate via Family Radio Service or General Mobile Radio Service, Motorola-branded or certified accessories sold for use with these Products (Accessories) and Motorola software contained on CD-ROMs or other tangible media and sold for use with these Products (Software) to be free from defects in materials and workmanship under normal consumer usage for the period(s) outlined below. This limited warranty is a consumer's exclusive remedy, and applies as follows to new Motorola Products, Accessories and Software purchased by consumers in the United States, which are accompanied by this written warranty. Y T N A R R A W English 76 Products and Accessories Products Covered Length of Coverage Products and Accessories as defined above, unless otherwise provided for below. One (1) year from the date of purchase by the first consumer purchaser of the product unless otherwise provided for below. Decorative Accessories and Cases. Decorative covers, bezels, PhoneWrap covers and cases. Business Two-way Radio Accessories Products and Accessories that are Repaired or Replaced. Limited lifetime warranty for the lifetime of ownership by the first consumer purchaser of the product. One (1) year from the date of purchase by the first consumer purchaser of the product. The balance of the original warranty or for ninety (90) days from the date returned to the consumer, whichever is longer. Exclusions Normal Wear and Tear. Periodic maintenance, repair and replacement of parts due to normal wear and tear are excluded from coverage. Batteries. Only batteries whose fully charged capacity falls below 80% of their rated capacity and batteries that leak are covered by this limited warranty. Abuse & Misuse. Defects or damage that result from: (a) improper operation, storage, misuse or abuse, accident or neglect, such as physical damage (cracks, scratches, etc.) to the surface of the product resulting from misuse; (b) contact with liquid, water, rain, extreme humidity or heavy perspiration, sand, dirt or the like, extreme heat, or food; (c) use of the Products or Accessories for commercial purposes or subjecting the Product or Accessory to abnormal usage or conditions; or (d) other acts which are not the fault of Motorola, are excluded from coverage. Use of Non-Motorola Products and Accessories. Defects or damage that result from the use of Non-Motorola branded or certified Products, Accessories, Software or other peripheral equipment are excluded from coverage. Unauthorized Service or Modification. Defects or damages resulting from service, testing, adjustment, installation, maintenance, alteration, or modification in any way by someone other than Motorola, or its authorized service centers, are excluded from coverage. Altered Products. Products or Accessories with
(a) serial numbers or date tags that have been removed, altered or obliterated; (b) broken seals or that show evidence of tampering; (c) mismatched board serial numbers; or (d) nonconforming or non-Motorola housings, or parts, are excluded form coverage. W A R R A N T Y 77 English Communication Services. Defects, damages, or the failure of Products, Accessories or Software due to any communication service or signal you may subscribe to or use with the Products Accessories or Software is excluded from coverage. Software Products Covered Length of Coverage Software. Applies only to physical defects in the media that embodies the copy of the software (e.g. CD-
ROM, or floppy disk). Ninety (90) days from the date of purchase. Y T N A R R A W Exclusions Software Embodied in Physical Media. No warranty is made that the software will meet your requirements or will work in combination with any hardware or software applications provided by third parties, that the operation of the software products will be uninterrupted or error free, or that all defects in the software products will be corrected. English 78 Software NOT Embodied in Physical Media. Software that is not embodied in physical media
(e.g. software that is downloaded from the internet), is provided as is and without warranty. WHO IS COVERED?
This warranty extends only to the first consumer purchaser, and is not transferable. HOW TO OBTAIN WARRANTY SERVICE OR OTHER INFORMATION?
Contact your Motorola point of purchase. SOFTWARE COPYRIGHT NOTICE The Motorola products described in this manual may include copyrighted Motorola and third party software stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola and third party software providers certain exclusive rights for copyrighted software, such as the exclusive rights to distribute or reproduce the copyrighted software. Accordingly, any copyrighted software contained in the Motorola products may not be modified, reverse-engineered, distributed, or reproduced in any manner to the extent allowed by law. EXPORT LAW ASSURANCES This product is controlled under the export regulations of the United States of America. The Governments of the United States of America may restrict the exportation or re-exportation of this product to certain destinations. For further information contact the U.S. Department of Commerce. Furthermore, the purchase of the Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents, or patent applications of Motorola or any third party software provider, except for the normal, non-
exclusive, royalty-free license to use that arises by operation of law in the sale of a product. PATENT NOTICE This product is covered by one or more of the following United States patents. 5896277 5894292 5864752 5699006 5742484 D408396 D399821 D387758 D389158 5894592 5893027 5789098 5734975 5861850 D395882 D383745 D389827 D389139 5929825 5926514 5953640 6071640 D413022 D416252 D416893 D433001 W A R R A N T Y 79 English I S E R O S S E C C A ACCESSORIES ANTENNAS Part No. Description RAN4033 RAN4041 RAN4031 UHF Stubby Antenna 450-470 MHz VHF Helical Antenna 146-174 MHz UHF Whip Antenna 438 - 470 MHz AUDIO ACCESSORIES Part No. Description 53865 53866 56517 56518 BATTERY Headset w/Swivel Boom Mic Earbud w/Clip PTT Mic BR Earpiece w/Inline Mic Earpiece w/Boom Mic Part No. Description RLN6306 Alkaline Battery Frame Part No. Description RLN6351 Standard Li-Ion Battery 53815 53862 53863 Headset w/Boom Mic BR Remote Speaker Mic BR Earpiece w/Mic BR RLN6305 RLN6308 High Capacity Li-Ion Battery Ultra High Capacity Li-Ion Battery English 80 CARRY ACCESSORIES CABLES Part No. Description Part No. Description RLN6302 Hard Leather Carry Case RLN6303 Radio to Radio Cloning Cable RLN6307 Spring Action Belt Clip RKN4155 CPS Programming Cable POWER SUPPLIES AC PIN ADAPTORS CHARGERS Part No. Description Part No. Description A C C E S S O R E S I RLN6349 North America AC Pin Adaptor SOFTWARE APPLICATIONS Part No. Description RVN5147 Computer Programming Software (CPS) RLN6304 RLN6309 Rapid ACCY Charging Kit -
Americas (*) Multi Unit Charger (MUC) Kit -
North America RLN6175 Standard Drop-in Tray Charger 81 English I S E R O S S E C C A POWER SUPPLIES Part No. Description RPN4054 RPN4058 Standard US Fixed Power Supply Standard Exchg AC pin Pwr Supply RLN6170 Rapid Exchg AC pin Pwr Supply Attention: Certain accessories may be or may not be available at the time of purchase. For latest information on accessories, contact your Motorola point of purchase or visit:
www.motorola.com/RDX or www.motorola.com/
radios/business
(*) Americas Rapid Charging Kit includes Power Supply, Drop-in Tray Charger, and AC Pin adaptors. English 82 RDX Series Features Summary M Features Programmable Via RADIO PANEL Programmable via CPS Display Non-
Display Display Non-
Display Default Value Programming Tips Backlight No N/A Yes N/A 5 Seconds Choose the backlights time out by using the CPS. Bandwidth Select Battery Save
(2) Yes No Yes Yes Frequency Dependable Yes Yes Yes Yes ON Battery Type Yes No Yes Yes Li-Ion Front panel programming available only on display models by entering Programming Mode (1). Bandwidth is programmable according to FCC frequency regulations. Refer to the Frequencies and Code Charts Section for details. To enable/disable Battery Save, press SB1 and SB2 simultaneously while turning ON the radio. Front panel radio programming is available in display models by pressing the MENU button and scrolling down/up with value. Long press PTT to save and exit. and buttons to set Buttons Reset No No Yes Yes ON Available only via CPS. Allows to reset the radio buttons to factory default values. Refer to Radio Buttons Summary Table. 83 Features Programmable Via RADIO PANEL Programmable via CPS Display Non-
Display Display Non-
Display Call Tones (4) Yes No Yes Yes Default Value Programming Tips OFF /
BUTTON A Front panel radio programming available only for Display Models by going into Programming Mode(1). Values available are 0 (OFF),1, 2 and 3. To enable/disable Call Tones press Button A (default button). Channel Aliasing Yes N/A Yes N/A OFF Channels Yes Yes Yes Yes Model Dependant 84 buttons Only Display Models. To enter or exit Channel Aliasing mode press PTT and simultaneously while turning radio ON for 3 sec. After editing, to exit and save, long press PTT. Note: To edit, refer to Programming Features/
Editing Channels. You can select channels using the Channel Selector Knob (non-display models) or the MENU button
(display models). You can also add or delete channels by using the CPS. Note: Enabling/disabling channels via CPS will automatically affect the Max Channels you are able to program via front panel. Features Programmable Via RADIO PANEL Programmable via CPS Display Non-
Display Display Non-
Display Default Value Programming Tips Cloning Mode Yes Yes Yes Yes OFF CPS Manager Lock End of Tx Tone (or Roger Beep)
(2) No No Yes Yes N/A Yes Yes Yes Yes OFF Enables radio to enter cloning mode in order to clone its profile settings into other radios (using Radio to Radio Cloning Cable or Multi-Unit Charger). Press PTT, SB2 while turning radio ON. Note: You can clone radios using the CPS. This feature is referred in the CPS software as Codeplug Password. It prevents unauthorized access to the CPS to the radios programmed configuration. Make sure you set up a 4 digits password that is easy to remember. To enable/disable press SB1 while powering up the radio Frequencies Yes Yes Yes Yes Channel and Model Dependant There are 27 VHF frequencies and 89 UHF frequencies available. Use Programming Mode (1) for front panel radio programming. Refer to Frequencies and Codes Charts Section for details. 85 Programmable Via RADIO PANEL Programmable via CPS Display Non-
Display Display Non-
Display No No Yes Yes Default Value Programming Tips Allows you to customize frequencies in your radio. Available only for certain 4W/5W radio models. Any value within radio frequency band N/A N/A N/A N/A Model Dependant Yes Yes Yes Yes Channel and Model Dependant Yes N/A N/A N/A OFF Radios Bandwidth is fixed and non-programmable. Bandwidth Range for 2W radios: VHF 150.8 - 160 Mhz / UHF 450-470 Mhz Bandwidth Range for 4W/
5W radios: VHF: 146-174 Mhz / UHF 438-470 Mhz. Use Programming Mode for front panel radio programming. There are 122 codes available.For details refer to Frequencies and Codes Charts Section. Hands free without accessories, available for display models only. To enable IVOX long press the PTT button while turning radio ON and until the IVOX icon blinks. Features Frequencies, Direct Input
(3) Bandwidth Range Codes, Interference Eliminator Codes
(CTCSS/DPL) IVOX, enable/
disable 86 Features IVOX, sensitivity Level Keypad Beep (
or Keypad Tone) (2) Keypad Lock
(2) LEDs Enabled/
Disabled Low Battery Alert -
Shutdown Programmable Via RADIO PANEL Programmable via CPS Display Non-
Display Display Non-
Display Yes N/A Yes N/A Default Value Programming Tips HIGH
(Level 3) Available for Display models only. Allows user to specify IVOX sensitivity level. For front panel radio programming use the MENU button. Yes Yes Yes Yes ON Press SB2 while turning ON radio to enable/disable keypad beep. Yes N/A No No Yes Yes N/A Yes UNLOCKED Press and hold MENU for 4 seconds to lock the radio keypad.To unlock, press MENU for 4 seconds. Enabled Using CPS you can disable radio LEDs N/A N/A N/A N/A ON Gives a sequence of loud and high beep tones to alert battery level is low. LED will blink orange several times. This a non-programmable feature. 87 Features Programmable Via RADIO PANEL Programmable via CPS Display Non-
Display Display Non-
Display Maximum Channels (2) Microphone Gain Level, ACCESSORY Microphone Gain Level, RADIO Yes No Yes Yes Yes Yes No No Yes Yes Yes Yes Default Value Programming Tips Model and CPS programmable dependant Medium
(Level 2) Medium
(Level 2) Front panel radio programming (only Display models): Set radio to Programming Mode(1) to get the Maximum Channels Menu option. Note: Default value is set to the maximum number of channels that the radio supports. For front panel programming enter Programming Mode (1). For front panel programming enter Programming Mode (1). Monitor (4) Yes Yes Yes Yes SB1 Button Long Press SB1 to monitor and press SB1 again to release. Note: PL/DPL defeat feature should be disabled in order to monitor. 88 Features Programmable Via RADIO PANEL Programmable via CPS Display Non-
Display Display Non-
Display Default Value Programming Tips Nuisance Ch Delete (4) Yes Yes Yes Yes SB2 Button PL Defeat Yes Yes Yes Yes SB1 Button Power Select
(4) No No Yes Yes High Power
(Model dependant) Press SB2 to start scanning and wait until the radio lands on the channel you want to delete. Long press SB2 to delete the channel. Note: The nuisance deleted channel will be restored into the scan list when the radio is turned OFF or you exit SCAN. Also known as Squelch defeat. Short Press SB1 to enable PL/DPL defeat so you can listen or monitor any activity in the channel without noise. Press SB1 again to disable PL/DPL defeat. Use CPS for selecting the transmission power level you want for each channel. Power level default depends on maximum power the radio supports. Note: There may be power restrictions depending on the frequency chosen in each channel. 89 Features Programmable Via RADIO PANEL Programmable via CPS Display Non-
Display Display Non-
Display Default Value Programming Tips Power up Text No N/A Yes N/A MOTOROLA Repeater/
Talkaround (3) Reset to Factory Defaults (2) No No Yes Yes OFF Yes Yes Yes Yes Enabled Reverse Burst No No Yes Yes 180 Text that shows up in the radio display when turned ON. Default text is MOTOROLA. Programmable via CPS. Available only for RDU4163d and RDU4160d radio models. Allows to restore radio's factory defaults. Press PTT, SB1, SB2 simultaneously for 3 seconds while turning ON radio. Reverse Burst eliminates unwanted noise (squelch tail) during loss of carrier detection. Use CPS to select values 180 or 240. 90 Features Programmable Via RADIO PANEL Programmable via CPS Display Non-
Display Display Non-
Display Default Value Programming Tips Scan Yes Yes N/A N/A SB2 Button Short press SB2 to enable/disable scan. Scan List Yes No Yes Yes ON - All Channels Scan, Auto Scan No Yes No Yes OFF Use CPS for editing Scan List (adding/removing channels to be scanned). For display models only:
you can add/delete channels in the scan list using front panel by going into Programming Mode(1). Feature available only for Non Display Models. For front programming using front panel radio enter Programming Mode(1) Scramble (4) Yes No Yes Yes OFF
(level 0) Display models only: you can program scramble using front panel by going into Programming Mode(1). Time-Out Timer No No Yes Yes 60 seconds Use CPS to program to program how long the PTT can be pressed before the transmission is automatically terminated. Values are 60, 120 and 180 seconds. (Pressing again PTT will start the transmission again). 91 Features VOX Sensitivity Level VOX, enable/
disable Programmable Via RADIO PANEL Programmable via CPS Display Non-
Display Display Non-
Display Default Value Programming Tips Yes No Yes Yes OFF
(level 0) Yes Yes Yes Yes OFF Front panel radio programming available in display models by pressing PTT or MENU buttons and scrolling down/up with and value. Long press PTT to save. buttons to set Allows to use hands-free mode connecting microphone accessories. To enable connect external accessory and power up radio. Note: The VOX sensitivity level default value is set to OFF in the CPS settings. Before using this feature, check VOX sensitivity level.
(1) To enter Programming Mode, press and hold both PTT and SB1 simultaneously for 3-5 seconds while turning radio ON (LED will start to blink green). Short press PTT to get to the different programming options. For setting values, press and buttons.
(2) Using CPS you can prevent this feature to be programmed via front panel radio.
(3) Contact your Motorola Point of purchase for enabling this feature and/or for radio models details.
(4) For Non-Display Models, feature can be enabled for front panel programming by assigning feature to SB1 or SB2. For Display models:
Feature can be enabled to any of the programmable buttons rather than the default ones. For more details refer to Programming Buttons Chart or CPS Menus. 92 Programmable Buttons Chart Scan /
Nuisance Delete Default Button Monitor Default SB1 SB2 BUTTON A (*) BUTTON B (*) BUTTON C (*) Notes:
Call Tone Power Select Scramble Backlight Channel Preset 1 Channel Preset 2 No Operation Default N/A N/A N/A N/A N/A N/A Default Default Buttons come programmed to default functions. Using CPS you can assign one of the features shown in the chart, so the button can toggle values using radio front panel
(*) Display models only. 93 Icons Chart Icon Symbol Comments Battery Level Displayed during normal radio mode operation, displays battery life remaining Displayed during normal radio operation and when programming channel features Displayed during normal radio operation and when programming codes features Displayed during normal radio operation and when programming frequency features Displayed whenever the Keypad lock feature is enabled (keypad is locked) Displayed whenever the radio is set up to Programming Mode. G L Displayed whenever the radio is set to SCAN mode. Displayed whenever scramble is enabled. Channel Code Frequency Keypad lock Program Scan Scramble 94 Icon Symbol Comments Power Select Displayed whenever the channel is transmitting or set to a high-power selection Signal Strength RSSI Display Icon numbers of bars will indicate the strength of the received signal. Vox/IVox Displayed when IVOX/VOX enabled or when programming MIC / MIC gain features. 95 2007 Motorola Inc. All rights reserved. Motorola Technology Sdn Bhd (Co. No. 455657-H) Plot 2 Bayan Lepas Technoplex Industrial Park Mukim 12 S.W.D 11900 Penang, Malaysia Printed in Malaysia September 2007
*6871663M01*
6871663M01-A
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2008-03-06 | 438 ~ 470 | TNF - Licensed Non-Broadcast Transmitter Held to Face | Class II permissive change or modification of presently authorized equipment |
2 | 2007-11-29 | 438 ~ 470 | TNF - Licensed Non-Broadcast Transmitter Held to Face | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2008-03-06
|
||||
1 2 |
2007-11-29
|
|||||
1 2 | Applicant's complete, legal business name |
Motorola Solutions, Inc.
|
||||
1 2 | FCC Registration Number (FRN) |
0003778479
|
||||
1 2 | Physical Address |
8000 West Sunrise Blvd
|
||||
1 2 |
Ft Lauderdale, Florida 33322
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
T******@TIMCOENGR.COM
|
||||
1 2 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 2 | Grantee Code |
AZ4
|
||||
1 2 | Equipment Product Code |
89FT4882
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
D******** Z******
|
||||
1 2 | Title |
Regulatory Compliance Manager
|
||||
1 2 | Telephone Number |
95472********
|
||||
1 2 | Fax Number |
--********
|
||||
1 2 |
d******@motorolasolutions.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 | Yes | |||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 01/13/2008 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | TNF - Licensed Non-Broadcast Transmitter Held to Face | ||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | PORTABLE 2-WAY RADIO | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Class II permissive change or modification of presently authorized equipment | ||||
1 2 | Original Equipment | |||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Power listed is conducted. Maximum conducted output power is 4.2W according to 90.205(s). This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50%. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration to comply with the Occupational/Controlled SAR limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements. SAR compliance for body-worn operating configurations is limited to the specific belt-clip, holster, and accessories tested for this filing and to belt-clips, holsters, or similar accessories that have no metallic component in the assembly and which provide at least 2.5 cm separation between the device, including its antenna, and the users body. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR levels are: Head: 4.11 W/kg for 50% Duty Cycle; Body: 7.01 W/kg for 50% Duty Cycle. | ||||
1 2 | Power listed is conducted. Maximum conducted output power is 4.2W according to 90.205(s). This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50%. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration to comply with the Occupational/Controlled SAR limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements. SAR compliance for body-worn operating configurations is limited to the specific belt-clip, holster, and accessories tested for this filing and to belt-clips, holsters, or similar accessories that have no metallic component in the assembly and which provide at least 2.5 cm separation between the device, including its antenna, and the users body. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR levels are: Head: 3.33 W/kg for 50% Duty Cycle; Body: 3.68 W/kg for 50% Duty Cycle. | |||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Motorola
|
||||
1 2 | Name |
W**** E****
|
||||
1 2 | Telephone Number |
954-7********
|
||||
1 2 | Fax Number |
954-7********
|
||||
1 2 |
F******@motorolasolutions.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 9 | 438 | 470 | 2 | 2 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 2 | 9 | 438 | 470 | 2 | 2 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 3 | 9 | 438 | 470 | 4 | 2 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 4 | 9 | 438 | 470 | 4 | 2 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 9 | 438 | 470 | 2 | 2 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
2 | 2 | 9 | 438 | 470 | 2 | 2 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
2 | 3 | 9 | 438 | 470 | 4 | 2 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
2 | 4 | 9 | 438 | 470 | 4 | 2 ppm | 11K0F3E |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC