all | frequencies |
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
RF Safety Booklet | Users Manual | 418.84 KiB | ||||
1 |
|
Stuffer for User Manual | Users Manual | 370.50 KiB | ||||
1 |
|
Users Manual | Users Manual | 1.29 MiB | ||||
1 | Attestation Statements | |||||||
1 | Cover Letter(s) | |||||||
1 | Cover Letter(s) | |||||||
1 | External Photos | |||||||
1 | Internal Photos | |||||||
1 | Cover Letter(s) | |||||||
1 | ID Label/Location Info | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | RF Exposure Info | |||||||
1 | Test Report | |||||||
1 | Test Setup Photos |
1 | RF Safety Booklet | Users Manual | 418.84 KiB |
Product Safety and RF Exposure for Portable Two-Way Radios
C a u t i o n BEFORE USING THIS RADIO, READ THIS BOOKLET WHICH CONTAINS IMPORTANT OPERATING INSTRUCTIONS FOR SAFE USAGE AND RF ENERGY AWARENESS AND CONTROL INFORMATION FOR COMPLIANCE WITH RF ENERGY EXPOSURE LIMITS IN APPLICABLE NATIONAL AND INTERNATIONAL STANDARDS. The information provided in this document supersedes the general safety information contained in user guides published prior to February 2002. For radios that have been approved as intrinsically safe, read the instructions and information on intrinsic safety on page 9 of this booklet. Compliance with RF Energy Exposure Standards NOTICE: This radio is intended for use in occupational/controlled applications where users have been made aware of the potential for exposure and can exercise control over their exposure. This radio device is NOT authorized for general population, consumer or similar use. Motorola, Inc. 2003 8000 W. Sunrise Blvd., Ft. Lauderdale, FL 33322 Printed in U.S.A. 3/03.
*6881095C98*
68P81095C98-A English Federal Communication Commission (FCC) Regulations The FCC has established limits for safe exposure to radio frequency (RF) emissions from portable two-way radios. The FCC requires manufacturers to demonstrate compliance with RF exposure limits before portable two-way radios can be marketed in the U.S. When two-way radios are approved for occupational/
controlled environment exposure limits, the FCC requires users to be fully aware of, and exercise control over, their exposure. Awareness and control of RF exposure can be accomplished by the use of labels, or by education and training through appropriate means, such as information and instructions in user manuals or safety booklets. Your Motorola two-way radio has an RF exposure information label in the battery compartment. This user safety booklet includes useful information about RF exposure and helpful instructions on how to control your RF exposure. Your Motorola two-way radio is designed and tested to comply with a number of national and international standards and guidelines (listed below) regarding human exposure to RF electromagnetic energy. This radio complies with the IEEE (FCC) and ICNIRP exposure limits for occupational/controlled RF exposure environments at usage factors of up to 50% talk50% listen. In terms of measuring RF energy for compliance with FCC exposure guidelines, your radio radiates measurable RF energy only while it is transmitting
(during talking), not when it is receiving (listening) or in standby mode. NOTE: The approved batteries, supplied with this radio, are rated for a 5-5-90 duty cycle (5% talk5% listen90% standby), even though this radio complies with FCC occupational exposure limits at usage factors of up to 50% talk. English 2 Your Motorola two-way radio complies with the following RF energy exposure standards and guidelines:
United States Federal Communications Commission, Code of Federal Regulations; 47CFR part 2 sub-part J American National Standards Institute (ANSI) / Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1992 Institute of Electrical and Electronic Engineers (IEEE) C95.1-1999 Edition International Commission on Non-Ionizing Radiation Protection (ICNIRP) 1998 Ministry of Health (Canada) Safety Code 6. Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz, 1999 Australian Communications Authority Radiocommunications (Electromagnetic Radiation Human Exposure) Standard, 2001 ANATEL, Brasil Regulatory Authority, Resolution 256 (April 11, 2001) additional requirements for SMR, cellular and PCS product certification. Compliance and Control Guidelines and Operating Instructions for Portable Two-Way Radios To control your exposure and ensure compliance with the occupational/
controlled environment exposure limits, always adhere to the following procedures:
Transmit no more than 50% of the time. To transmit (talk), push the Push-
To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting 50% of the time or less is important since the radio generates measurable RF energy exposure only when transmitting (in terms of measuring standards compliance). 3 English Hold the radio in a vertical position in front of the face with the microphone (and other parts of the radio including the antenna) at least one to two inches (2.5 to 5 centimeters) away from the lips. Keeping the radio at a proper distance is important since RF exposures decrease with increasing distance from the antenna. For body-worn operation, always place the radio in a Motorola-approved clip, holder, holster, case, or body harness for this product. All Motorola-
approved accessory, antenna, and device combinations comply with FCC occupational/controlled environment RF exposure limits. Exposure information on various accessory, antenna, and device combinations can be found under the Display Exhibits section of http://www.fcc.gov/oet/
fccid after searching on the FCC ID number, which can be obtained from the label of your radio. Using nonMotorola-approved accessories may result in exposure levels which exceed the FCCs occupational/controlled environment RF exposure limits. If you are not using a body-worn accessory and are not using the radio in the intended use position in front of the face, ensure the antenna and the radio are kept one inch (2.5 centimeters) from the body when transmitting. Keeping the radio at a proper distance is important since RF exposures decrease with increasing distance from the antenna. Use only Motorola-approved supplied or replacement antennas, batteries, and accessories. Use of nonMotorola-approved antennas, batteries and accessories may exceed FCC RF exposure guidelines. For a list of Motorola-
approved antennas, batteries, and other accessories, visit the following web site which lists approved accessories:
http://www.motorola.com/cgiss/index.shtml For additional information on exposure requirements or other training information, visit http://www.motorola.com/rfhealth. English 4 Electromagnetic Interference/Compatibility NOTE: Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately shielded, designed, or otherwise configured for electromagnetic compatibility. Facilities To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any facility where posted notices instruct you to do so. Hospitals or health care facilities may be using equipment that is sensitive to external RF energy. Aircraft When instructed to do so, turn off your radio when on board an aircraft. Any use of a radio must be in accordance with applicable regulations per airline crew instructions. Medical Devices Pacemakers The Advanced Medical Technology Association (AdvaMed) recommends that a minimum separation of 6 inches (15 centimeters) be maintained between a handheld wireless radio and a pacemaker. These recommendations are consistent with those of the U.S. Food and Drug Administration. Persons with pacemakers should:
ALWAYS keep the radio more than 6 inches (15 centimeters) from their pacemaker when the radio is turned ON. Not carry the radio in the breast pocket. Use the ear opposite the pacemaker to minimize the potential for interference. Turn the radio OFF immediately if there is any reason to suspect that interference is taking place. 5 English Hearing Aids Some digital wireless radios may interfere with some hearing aids. In the event of such interference, you may want to consult your hearing aid manufacturer to discuss alternatives. Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. Driver Safety Check the laws and regulations on the use of radios in the area where you drive. Always obey them. When using your radio while driving, please:
Give full attention to driving and to the road. Use hands-free operation, if available. Pull off the road and park before making or answering a call if driving conditions so require. English 6 Operational Warnings
W A R N I N G For Vehicles With an Air Bag Do not place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. Potentially Explosive Atmospheres Turn off your radio prior to entering any area with a potentially explosive atmosphere, unless it is a portable radio type especially qualified for use in such areas as Intrinsically Safe (for example, Factory Mutual, CSA, UL, or CENELEC). Do not remove, install, or charge batteries in such areas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. The areas with potentially explosive atmospheres referred to above include fueling areas such as below decks on boats, fuel or chemical transfer or storage facilities, and areas where the air contains chemicals or particles such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often, but not always, posted. Blasting Caps and Blasting Areas To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: Turn off two-way radio. Obey all signs and instructions. 7 English Operational Cautions
C a u t i o n Antennas Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. Batteries All batteries can cause property damage and/or bodily injury such as burns if a conductive material such as jewelry, keys, or beaded chains touches exposed terminals. The conductive material may complete an electrical circuit (short circuit) and become quite hot. Exercise care in handling any charged battery, particularly when placing it inside a pocket, purse, or other container with metal objects. English 8 Intrinsically Safe Radio Information FMRC Approved Equipment Anyone intending to use a radio in a location where hazardous concentrations of flammable materials exist (hazardous atmosphere) is advised to become familiar with the subject of intrinsic safety and with the National Electric Code NFPA 70
(National Fire Protection Association) Article 500 (hazardous [classified]
locations). An Approval Guide, issued by Factory Mutual Research Corporation (FMRC), lists manufacturers and the products approved by FMRC for use in such locations. FMRC has also issued a voluntary approval standard for repair service
(Class Number 3605). FMRC Approval labels are attached to the radio to identify the unit as being FMRC Approved for specified hazardous atmospheres. This label specifies the hazardous Class/Division/Group along with the part number of the battery that must be used. Depending on the design of the portable unit, this FM label can be found on the back or the bottom of the radio housing. The FM Approval Mark is shown here. FM APPROVED
W A R N I N G Do not operate radio communications equipment in a hazardous atmosphere unless it is a type especially qualified (for example, FM Approved) for such use. An explosion or fire may result. Do not operate an FMRC Approved product in a hazardous atmosphere if it has been physically damaged (for example, cracked housing). An explosion or fire may result. Do not replace or charge batteries in a hazardous atmosphere. Contact sparking may occur while installing or removing batteries and cause an explosion or fire. 9 English
W A R N I N G Do not replace or change accessories in a hazardous atmosphere. Contact sparking may occur while installing or removing accessories and cause an explosion or fire. Turn the radio off before removing or installing a battery or accessory. Do not disassemble an FMRC Approved Product in any way that exposes the internal circuits of the unit. Radios must ship from the Motorola manufacturing facility with the hazardous atmosphere capability and FM Approval labeling. Radios will not be upgraded to this capability and labeled in the field. A modification changes the units hardware from its original design configuration. Modifications can only be made by the original product manufacturer at one of its FMRC-audited manufacturing facilities.
W A R N I N G Failure to use an FMRC Approved Product with an FMRC Approved battery or FMRC Approved accessories specifically approved for that product may result in the dangerously unsafe condition of an unapproved radio combination being used in a hazardous location. Unauthorized or incorrect modification of an FMRC Approved Product will negate the Approval rating of the product. English 10 Repair of FMRC Approved Products REPAIRS FOR MOTOROLA PRODUCTS WITH FMRC APPROVAL ARE THE RESPONSIBILITY OF THE USER. You should not repair or relabel any Motorola-manufactured communication equipment bearing the FMRC Approval label (FMRC Approved Product) unless you are familiar with the current FMRC Approval standard for repairs and service
(Class Number 3605). You may want to consider using a repair facility that operates under 3605 repair service approval.
W A R N I N G Incorrect repair or relabeling of any FMRC Approved Product could adversely affect the Approval rating of the unit. Use of a radio that is not intrinsically safe in a hazardous atmosphere could result in serious injury or death. The FMRCs Approval Standard Class Number 3605 is subject to change at any time without notice to you. You may want to obtain a current copy of 3605 from the FMRC. Per the December 1994 publication of 3605, some key definitions and service requirements are as follows:
Repair A repair constitutes something done internally to the unit that would bring it back to its original conditionApproved by FMRC. A repair should be done in an FMRC Approved repair facility. Items not considered as repairs are those in which an action is performed on a unit which does not require the outer casing of the unit to be opened in a manner that exposes the internal electrical circuits of the unit. You do not have to be an FMRC Approved repair facility to perform these actions. 11 English Relabeling The repair facility shall have a method by which the replacement of FMRC Approval labels are controlled to ensure that any relabeling is limited to units that were originally shipped from the manufacturer with an FM Approval label in place. FMRC Approval labels shall not be stocked by the repair facility. An FMRC Approval label shall be ordered from the original manufacturer, as needed, to repair a specific unit. Replacement labels may be obtained and applied by the repair facility, provided there is satisfactory evidence that the unit being relabeled was originally an FMRC Approved unit. Verification may include, but is not limited to a unit with a damaged Approval label, a unit with a defective housing displaying an Approval label, or a customer invoice indicating the serial number of the unit and purchase of an FMRC Approved model. Do Not Substitute Options or Accessories The Motorola communications equipment certified by Factory Mutual is tested as a system and consists of the FM Approved portable, FM Approved battery, and FM Approved accessories or options, or both. This FM Approved portable and battery combination must be strictly observed. There must be no substitution of items, even if the substitute has been previously Approved with a different Motorola communications equipment unit. Approved configurations are listed in the FM Product Listing Manual that was included with your radio. English 12 Normas de seguridad y exposicin a la energa de RF al usar radios bidireccionales porttiles
Precaucin ANTES DE USAR EL RADIO LEA ESTE FOLLETO, EL CUAL CONTIENE INSTRUCCIONES DE OPERACIN IMPORTANTES PARA SU USO SEGURO, E INFORMACIN SOBRE LA ENERGA DE RF Y SU CONTROL, A FIN DE GARANTIZAR CONFORMIDAD CON LOS LMITES DE EXPOSICIN A LA ENERGA DE RADIOFRECUENCIA ESTABLECIDOS EN LAS NORMAS NACIONALES E INTERNACIONALES APLICABLES. La informacin incluida en este documento reemplaza la informacin de seguridad general contenida en los manuales de usuario publicados antes de febrero de 2002. Si el radio ha sido aprobado como intrnsecamente seguro, lea las instrucciones y la informacin sobre seguridad intrnseca en la pgina 10 de este folleto. Conformidad con las normas de exposicin a la energa de RF AVISO: Este radio fue diseado para uso en entornos ocupacionales o controlados, donde los usuarios han sido advertidos acerca del peligro al que se exponen y estn en capacidad de controlar el riesgo. Esta unidad de radio NO est aprobada para la venta al pblico en general en el mercado de consumo masivo. 1 Espaol Regulaciones de la Comisin Federal de Comunicaciones de EE.UU. (FCC) La FCC ha establecido lmites para la exposicin prudente a las emisiones de radiofrecuencia (RF) de radios bidireccionales porttiles. La FCC exige a los fabricantes demostrar que sus radios bidireccionales porttiles cumplen con los lmites de exposicin a la energa de RF para poder comercializarlos en el mercado estadounidense. Cuando un radio bidireccional ha sido aprobado por cumplir con los lmites de exposicin en entornos ocupacionales o controlados, la FCC exige que los usuarios estn plenamente conscientes del peligro al que se exponen y estn en capacidad de controlar el riesgo. La toma de consciencia y el control de la exposicin a la energa de RF se pueden lograr mediante el uso de etiquetas, o mediante instruccin y capacitacin con los medios apropiados como, por ejemplo, la informacin e instrucciones proporcionadas en manuales de usuario o folletos de seguridad. Su radio bidireccional Motorola tiene una etiqueta con informacin acerca de la exposicin a la energa de RF en el compartimiento de la batera. Este folleto de seguridad incluye informacin acerca de la exposicin a la energa de RF e instrucciones tiles sobre cmo controlar dicha exposicin. Este radio bidireccional Motorola ha sido diseado y verificado para garantizar su compatibilidad con las siguientes normas y recomendaciones nacionales e internacionales relacionadas con la exposicin de los seres humanos a la energa electromagntica de RF: este radio cumple con los lmites de exposicin establecidos por el IEEE (FCC) y la ICNIRP para entornos ocupacionales o con control de exposicin a la energa de radiofrecuencia, a ciclos de trabajo de hasta 50% (50% transmisin / 50% recepcin). En lo que respecta a la medicin de energa de RF para la determinacin de conformidad con las pautas de exposicin de la FCC, el radio irradia energa de RF medible slo cuando est transmitiendo (cuando el usuario est hablando), no cuando est recibiendo (cuando el usuario est oyendo) ni cuando est en reposo. Espaol 2 NOTA: Las bateras aprobadas que se suministran con este radio soportan un ciclo de trabajo de 5-5-90 (5% del tiempo transmitiendo, 5% recibiendo y 90% en reposo), aun cuando este radio satisface los lmites de exposicin ocupacional de la FCC a ciclos de trabajo de hasta 50%. Este radio bidireccional Motorola satisface las siguientes normas y recomendaciones relacionadas con la exposicin a la energa de radiofrecuencia:
Comisin Federal de Comunicaciones de EE.UU. (FCC), Cdigo de Reglamentos Federales; 47CFR parte 2 subparte J. Instituto Nacional Americano de Normas (ANSI) / Instituto de Ingenieros Elctricos y Electrnicos (IEEE) C95. 1-1992. Instituto de Ingenieros Elctricos y Electrnicos (IEEE) (C95.1 Edicin 1999). Comisin Internacional para la Proteccin contra la Radiacin no Ionizante
(ICNIRP) 1998. Ministerio de Sanidad (Canad), Cdigo de seguridad 6. Lmites de la exposicin humana a los campos electromagnticos de radiofrecuencia en el rango de frecuencias de 3 kHz a 300 GHz (1999). Direccin Australiana de Comunicaciones, Normativa de Radiocomunicaciones de 2001 (exposicin humana a la radiacin electromagntica). ANATEL, Ente Regulador de Brasil, Resolucin 256 (11 de abril de 2001) requisitos adicionales para la certificacin de productos SMR, celulares y PCS. 3 Espaol Pautas de control y conformidad, e instrucciones de operacin de radios bidireccionales porttiles Para controlar su exposicin y asegurar la conformidad con los lmites de exposicin en un entorno ocupacional o controlado, observe siempre los procedimientos siguientes:
No transmita ms del 50% del tiempo. Para transmitir (hablar) presione el botn de transmisin (PTT). Para recibir llamadas, suelte el botn PTT. Es importante no transmitir ms del 50% del tiempo, ya que el radio emite energa de RF medible slo cuando est transmitiendo (en trminos de conformidad con las normas de medicin). Sostenga el radio en posicin vertical frente a la cara, con el micrfono (y las dems partes del radio, incluida la antena) a una distancia mnima entre 2,5 y 5 centmetros (1 y 2 pulg.) de los labios. Es importante mantener el radio a una distancia adecuada ya que la exposicin a la RF disminuye al aumentar la distancia de la antena. Cuando use el radio ajustado al cuerpo, siempre colquelo en un clip, sujetador para cinturn, estuche o arns para el cuerpo, que haya sido aprobado por Motorola para uso con este producto. Todas las combinaciones de dispositivos, accesorios, y antenas aprobadas por Motorola cumplen con los lmites de exposicin a la energa de RF establecidos por la FCC para entornos ocupacionales o entornos controlados. Informacin de la exposicin con las combinaciones de dispositivos, accesorios, y antenas se puede encontrar bajo la seccin de Display Exhibits de la pgina WEB http://www.fcc.gov/oet/fccid al ingresar y buscar en esta pgina el nmero FCC ID que puede ser obtenido de la etiqueta en su radio. El uso de accesorios no aprobados por Motorola puede dar lugar a niveles de exposicin superiores a los lmites de exposicin a la energa de RF establecidos por la FCC para entornos ocupacionales o entornos controlados. Espaol 4 Si no emplea accesorios de Motorola para uso ajustado al cuerpo y no est usando el radio en la posicin usual frente a la cara, no olvide mantener la antena y el radio a una distancia mnima de 2,5 cm (una pulgada) del cuerpo al transmitir. Es importante mantener el radio a una distancia adecuada ya que la exposicin a la RF disminuye al aumentar la distancia de la antena. Use nicamente antenas, bateras y accesorios suministrados por Motorola o reemplazos aprobados por Motorola. Si se emplean antenas, bateras o accesorios no aprobados por Motorola se podran exceder los lmites de exposicin a la energa de radiofrecuencia establecidos por la FCC. Para consultar la lista de antenas, bateras y dems accesorios aprobados por Motorola visite el siguiente sitio Web:
http://www.motorola.com/cgiss/index.shtml Para obtener informacin adicional sobre los requisitos de exposicin o sobre capacitacin, visite: http://www.motorola.com/rfhealth. Interferencia y compatibilidad electromagntica NOTA: Casi todos los dispositivos electrnicos son susceptibles a la interferencia electromagntica (EMI) si no cuentan con el debido blindaje o si no estn diseados o configurados de manera que sean compatibles con este tipo de seales electromagnticas. Edificaciones Para evitar problemas de interferencia y/o compatibilidad electromagntica, apague el radio donde haya letreros que as lo establezcan. Por ejemplo, los hospitales y establecimientos de asistencia mdica podran estar usando aparatos sensibles a la energa de RF externa. 5 Espaol Aeronaves Cuando est a bordo de un avin, apague el radio cuando se le indique. Si usa el radio, deber hacerlo de conformidad con las regulaciones de la lnea area y las instrucciones de la tripulacin. Aparatos mdicos Marcapasos La Asociacin de Tecnologa Mdica Avanzada (AdvaMed, Advanced Medical Technology Association) recomienda mantener una distancia mnima de 15 centmetros (6 pulgadas) entre un radio inalmbrico de mano y un marcapasos. Estas recomendaciones concuerdan con las disposiciones del organismo estadounidense para el control de alimentos y drogas (FDA, Food and Drug Administration). Las personas que utilicen marcapasos deben seguir las recomendaciones que se presentan a continuacin:
Mantener SIEMPRE el radio a una distancia de 15 centmetros (6 pulgadas) como mnimo del marcapasos cuando est encendido el radio. No llevar el radio dentro del bolsillo de la camisa. Utilizar el odo opuesto al marcapasos para minimizar la probabilidad de interferencia. Apagar el radio inmediatamente si sospecha que est produciendo interferencia. Aparatos auditivos Algunos radios inalmbricos digitales pueden interferir con ciertos aparatos auditivos. En caso de que exista interferencia, puede consultar con el fabricante del aparato auditivo para buscar posibles alternativas. Espaol 6 Otros dispositivos mdicos Si utiliza cualquier otro dispositivo mdico, consulte con el fabricante del dispositivo para determinar si est protegido adecuadamente contra la energa de RF externa. Su mdico podra ayudarle a obtener esta informacin. Seguridad al conducir Consulte las leyes y reglamentos para el uso de radios en las zonas donde conduce. Obedzcalas siempre. Cuando utilice el radio mientras conduce:
Preste atencin al camino durante la conduccin. Use la funcin de manos libres, si est disponible. Salga del camino y estacione antes de realizar o contestar una llamada, si las condiciones de la va lo requieren. 7 Espaol Advertencias operacionales
ADVERTENCIA Vehculos con bolsa de aire No coloque un radio porttil sobre una bolsa de aire o en el rea de despliegue de la misma. Las bolsas de aire se inflan con mucha fuerza. De haber un radio porttil en el rea de despliegue de la bolsa de aire cuando sta se infle, el radio podra salir proyectado con gran velocidad y ocasionar lesiones graves a los pasajeros. Ambientes potencialmente explosivos Apague el radio cuando est en una atmsfera potencialmente explosiva, salvo que use un tipo de radio porttil especficamente clasificado como intrnsecamente seguro (por ejemplo, por la Factory Mutual Research Corp., CSA, UL o CENELEC) para uso en tales reas. No retire, instale ni cargue bateras en estas reas. Las chispas en atmsferas potencialmente explosivas pueden desencadenar una explosin o incendio, y ocasionar lesiones o incluso la muerte. Entre los entornos potencialmente explosivos mencionados anteriormente, se encuentran las reas con combustible, por ejemplo, debajo de la cubierta de barcos, instalaciones de transferencia y almacenamiento de combustible o de productos qumicos, y reas donde el aire contiene productos qumicos o partculas tales como granos, cereales, polvo comn o polvo metlico. En las reas con atmsferas potencialmente explosivas generalmente hay seales de precaucin, aunque no siempre es as. reas de voladuras y explosivos Para evitar una posible interferencia con las operaciones de detonacin, apague el radio cuando est cerca de detonadores elctricos, en un rea de detonaciones o donde haya letreros que indiquen apagar los radios bidireccionales. Obedezca todas las seales e instrucciones. Espaol 8 Precauciones operacionales
Precaucin Antenas No utilice radios porttiles que tengan la antena daada. Si una antena daada hace contacto con la piel, podra producir una pequea quemadura. Bateras Todas las bateras pueden causar daos materiales, lesiones o quemaduras si un material conductor, por ejemplo, joyas, llaves o cadenas, hace contacto con los terminales expuestos. El material podra cerrar un circuito elctrico (cortocircuito) y tornarse muy caliente. Manipule con cuidado las bateras cargadas, especialmente cuando las lleve dentro de un bolsillo, cartera o envase que contenga objetos metlicos. 9 Espaol Informacin sobre radios intrnsecamente seguros Equipo aprobado por la FMRC Es aconsejable que toda persona que se proponga utilizar un radio en lugares con concentraciones peligrosas de sustancias inflamables (atmsferas peligrosas) se familiarice primero con el tema de la seguridad intrnseca y con el Artculo 500 (lugares [clasificados] peligrosos) del Cdigo Elctrico Nacional
(National Electrical Code), tambin conocido como NFPA 70, que publica la Asociacin Nacional de Proteccin contra Incendios de los EE.UU. (National Fire Protection Association). La Gua de Aprobacin FMRC, publicada por la Factory Mutual Research Corporation (FMRC), incluye una lista de fabricantes y productos aprobados por la FMRC para dichas reas. Igualmente, la FMRC ha publicado una norma de aprobacin voluntaria para establecimientos de reparacin (nmero de clase 3605). En el radio se han colocado etiquetas de aprobacin que identifican a la unidad como aprobada por la FMRC para las atmsferas peligrosas especificadas. En dichas etiquetas se establece el nmero de parte de la batera que se debe usar, as como la clase, divisin y grupo correspondientes. Segn el diseo de la unidad porttil, la etiqueta de la FMRC puede estar ubicada en la parte posterior de la cubierta del radio. El sello de aprobacin FMRC es igual al aqu mostrado. FM APPROVED Espaol 10
ADVERTENCIA No haga funcionar equipos de radiocomunicaciones en atmsferas peligrosas salvo que los mismos cuenten con las aprobaciones especiales correspondientes (por ejemplo, la aprobacin de la FMRC). De lo contrario, podran producirse explosiones o incendios. No opere un producto aprobado por la FMRC en una atmsfera peligrosa si el mismo presenta seales de daos fsicos (por ejemplo, la cubierta resquebrajada). De lo contrario, podran producirse explosiones o incendios. No cambie ni reinstale bateras en atmsferas peligrosas. De producirse chispas al instalar o sacar dichas bateras, podran originarse incendios o explosiones.
ADVERTENCIA No cambie ni reinstale accesorios en atmsferas peligrosas. De producirse chispas al instalar o sacar accesorios, podran originarse incendios o explosiones. Apague el radio antes de desinstalar o instalar bateras o accesorios. No desarme la unidad aprobada por la FMRC a un nivel tal que los circuitos internos queden al descubierto. Los radios debern ser enviados por la fbrica de Motorola con la capacidad para funcionar en atmsferas peligrosas y la etiqueta de aprobacin de la FMRC. Las unidades no se pueden "actualizar" con esta capacidad ni marcar con las etiquetas correspondientes en el campo. Toda modificacin alterar la configuracin de diseo original de los componentes de la unidad. Las modificaciones slo podrn ser realizadas por el fabricante del producto original en una fbrica autorizada por la FMRC. 11 Espaol
ADVERTENCIA El uso de un producto aprobado por la FMRC con una batera no aprobada por la FMRC o con un accesorio no aprobado por la FMRC (o no aprobado para usar con el producto) puede dar lugar a una condicin peligrosa semejante a la producida al usar una combinacin de radio no aprobada por la FMRC en un rea peligrosa. Toda modificacin incorrecta o no autorizada de un producto aprobado por la FMRC invalidar la aprobacin del producto. Reparacin de productos aprobados por la FMRC LA REPARACIN DE PRODUCTOS MOTOROLA APROBADOS POR LA FMRC ES RESPONSABILIDAD DEL USUARIO. El usuario no deber reparar ni cambiar la etiqueta de ningn equipo de comunicacin fabricado por Motorola que tenga la etiqueta de aprobacin de la FMRC (FMRC Approved Product [producto aprobado por la FMRC]) salvo que est capacitado para efectuar reparaciones y servicio de conformidad con las normas actuales de aprobacin FMRC (nmero de clase 3605). Se recomienda acudir a los establecimientos de reparacin que cuenten con la aprobacin de servicios de reparacin 3605.
ADVERTENCIA Toda reparacin o reposicin de etiquetas de cualquier producto aprobado por la FMRC podra afectar negativamente la clasificacin de la unidad. El uso de un radio que carezca de seguridad intrnseca en atmsferas peligrosas podra ocasionar lesiones graves o fatales. Espaol 12 La norma de aprobacin FMRC con nmero de clase 3605 est sujeta a cambios en cualquier momento sin previa notificacin. Sugerimos solicitar a la FMRC una copia actualizada de la norma 3605. En la mencionada norma 3605 publicada en diciembre de 1994 se incluyen las definiciones y requisitos de servicio siguientes:
Reparacin Una reparacin consiste en componer algo dentro de la unidad a fin de devolverle su condicin original, aprobada por la FMRC. Dicha reparacin se debe realizar en un establecimiento de reparacin aprobado por la FMRC. No se consideran reparaciones aquellas acciones efectuadas para las que no es necesario abrir la cubierta exterior de la unidad de forma que los circuitos elctricos internos de la unidad queden expuestos. Para efectuar este tipo de acciones no es necesario llevar la unidad a un establecimiento aprobado por la FMRC. Reemplazo de etiquetas El establecimiento de reparacin deber contar con un sistema mediante el cual se controle el reemplazo de las etiquetas de aprobacin FMRC, para garantizar que toda reposicin de etiquetas se realice nicamente en unidades que fueron enviadas originalmente por el fabricante con la referida etiqueta de aprobacin FMRC. El establecimiento de reparacin no deber mantener inventarios de etiquetas de aprobacin FMRC. Cada vez que sea necesario, deber solicitarse una etiqueta de aprobacin FMRC al fabricante original para reparar una unidad especfica. Las etiquetas de reemplazo podrn ser obtenidas y fijadas a la unidad por el establecimiento de reparacin, una vez que se haya proporcionado suficiente evidencia de que la unidad a la que se le reemplazar la etiqueta era originalmente una unidad aprobada por la FMRC. Para la verificacin se requiere, aunque no exclusivamente, una unidad con una etiqueta FMRC daada, una unidad con la cubierta defectuosa que tenga la etiqueta FMRC, o una factura al cliente que indique el nmero de serie de la unidad y la compra de un modelo aprobado por la FMRC. 13 Espaol No sustituya opciones ni accesorios Los equipos de comunicaciones de Motorola certificados por la Factory Mutual Research Corporation son probados a nivel de sistema y estn compuestos de una unidad porttil aprobada por la FMRC, una batera aprobada por la FMRC, y componentes opcionales y/o accesorios aprobados todos por la FMRC. El uso de esta combinacin aprobada por la FMRC de unidad porttil y batera deber observarse estrictamente. No debern usarse componentes sustitutos, aun cuando el sustituto haya sido aprobado previamente para uso con un equipo de comunicaciones Motorola diferente. Las configuraciones aprobadas aparecen en el manual de productos aprobados por la Factory Mutual Research Corporation que se incluy con el radio. Espaol 14 Normas de segurana e exposio energia de RF quando do uso de rdios bidirecionais portteis
Precauo ANTES DE UTILIZAR O RDIO PROCURE LER ESTE FOLHETO, QUE CONTM IMPORTANTES INSTRUES DE OPERAO PARA O USO SEGURO, BEM COMO INFORMAES SOBRE A ENERGIA DE RADIOFREQNCIA E SEU CONTROLE, COM A FINALIDADE DE GARANTIR A CONFORMIDADE COM OS LIMITES DE EXPOSIO ENERGIA DE RADIOFREQNCIA ESTABELECIDOS NAS NORMAS NACIONAIS E INTERNACIONAIS APLICVEIS. As informaes contidas neste documento substituem as informaes a respeito de segurana geral contidas nos manuais do usurio publicados antes de fevereiro de 2002. Se o rdio houver sido aprovado como intrinsecamente seguro, leia as instrues e as informaes de segurana intrnseca na pgina 10 deste folheto. Conformidade com as normas de exposio energia de RF AVISO: Este rdio foi projetado para uso em ambientes ocupacionais ou controlados, onde os usurios tenham sido advertidos a respeito do perigo a que se expem e estejam em condies de controlar o risco. Esta unidade de rdio NO aprovada para venda ao pblico em geral no mercado de consumo de massa. 1 Portugus Regulamentos da Comisso Federal de Comunicaes dos Estados Unidos (FCC) A FCC estabeleceu limites para a exposio segura s emisses de radiofreqncia (RF) de rdios portteis bidirecionais. A FCC exige dos fabricantes que os mesmos demonstrem que seus rdios portteis bidirecionais cumprem com os limites de exposio energia de RF para que possam comercializar os referidos rdios no mercado norte-americano. Quando um rdio bidirecional aprovado por cumprir com os limites de exposio em ambientes ocupacionais ou controlados, a FCC exige que os usurios estejam plenamente conscientes do perigo a que se expem e que estejam preparados para controlar o risco. A ateno e o controle da exposio da energia de RF podem ser obtidas por meio do uso de etiquetas ou por meio de treinamento e capacitao com os meios apropriados tais como, por exemplo, as informaes e instrues que constam em manuais de usurio ou folhetos de segurana. Seu rdio bidirecional Motorola contm uma etiqueta localizada no compartimento da bateria que traz as informaes a respeito da exposio energia de RF. Este folheto de segurana inclui informaes de segurana a respeito da exposio energia de RF e instrues teis a respeito de como controlar tal exposio. Este rdio bidirecional Motorola foi projetado e testado com a finalidade de garantir a sua compatibilidade com as normas e recomendaes nacionais e internacionais referentes exposio dos seres humanos energia eletromagntica de radiofreqncia: Este rdio atende aos limites de exposio estabelecidos pelo IEEE (FCC) e pela ICNIRP para ambientes ocupacionais ou com controle de exposio energia de radiofreqncia, em ciclos de trabalho de 50% (50% transmisso / 50% recepo). No que se refere medio da energia de RF para a determinao de conformidade com as orientaes de exposio da FCC, o rdio irradia energia de RF mensurvel somente quando est em transmisso (quando o usurio est falando) e no quando est recebendo (quando o usurio est ouvindo) ou quando se encontra em repouso. Portugus 2 NOTA: Embora este rdio atenda aos limites de exposio ocupacional estabelecidos pela FCC para ciclos de trabalho de at 50%, as baterias aprovadas fornecidas com este rdio suportam um ciclo de trabalho de 5-
5-90 (5% do tempo em transmisso, 5% em recepo e 90% em repouso). Este rdio bidirecional Motorola satisfaz s seguintes normas e recomendaes relacionadas exposio energia de radiofreqncia:
Comisso Federal de Comunicaes dos EUA (FCC), Cdigo de Regulamentos Federais; 47CFR parte 2 subparte J. Instituto Nacional Americano de Normas (ANSI) / Instituto de Engenheiros Eltricos e Eletrnicos (IEEE) C95. 1-1992. Instituto de Engenheiros Eltricos e Eletrnicos (IEEE) (C95.1 - Edio 1999). Comisso Internacional para Proteo contra Radiao no Ionizante
(ICNIRP) 1998. Ministrio da Sade (Canad), Cdigo de segurana 6. Limites da exposio humana aos campos eletromagnticos de radiofreqncia situados no intervalo de freqncias de 3 kHz a 300 GHz (1999). Autoridade Australiana de Comunicaes, Normativa de Radiocomunicaes de 2001 (exposio humana radiao eletromagntica). ANATEL, Agncia Reguladora do Brasil, Resoluo 256 (11 de abril de 2001) requisitos adicionais pata a certificao de produtos SMR, celulares e PCS. 3 Portugus Orientaes gerais de controle e conformidade e instrues de operao de rdios bidirecionais portteis Para controlar sua exposio e assegurar a conformidade com os limites de exposio em um ambiente ocupacional ou controlado, procure observar sempre os procedimentos descritos a seguir:
No transmita durante mais de 50% do tempo. Para transmitir (falar) pressione o boto de transmisso (PTT). Para receber chamadas solte o boto de transmisso (PTT). importante no transmitir mais de 50% do tempo, uma vez que o rdio emite energia de RF mensurvel somente quando est em transmisso (em termos da conformidade com as normas de medio). Mantenha o rdio na posio vertical em frente ao rosto, com o microfone (e as demais partes do rdio, incluindo a antena) a uma distncia mnima de 2,5 a 5,0 centmetros (1 a 2 polegadas) dos lbios. importante manter o rdio a uma distncia adequada uma vez que a exposio RF diminui ao se aumentar a distncia at a antena. Quando estiver operando o rdio ajustado ao corpo, procure coloc-lo em um clip, suporte para cinto ou estojo aprovado pela Motorola para ser usado com o este produto. Todas as combinaes dos dispositivos, acessrios, e antenas aprovadas pela Motorola concordam com os limites de exposio energia de RF estabelecidos pela FCC para ambientes ocupacionais o ambientes controlados. Informao a respeito da exposio das combinaes dos dispositivos, acessrios, e antenas podem ser obtida na seo de Display Exhibits localizada no website http://www.fcc.gov/oet/fccid, depois da procura o nmero do FCC ID, que pode ser encontrado na etiqueta do seu rdio. O uso de acessrios no aprovados pela Motorola pode resultar em nveis de exposio superiores aos limites de exposio estabelecidos pela FCC para ambientes ocupacionais o ambientes controlados. Portugus 4 Se no forem utilizados acessrios da Motorola para uso ajustado ao corpo e se o rdio no for utilizado na posio usual de frente ao rosto, no se esquea de manter uma distncia mnima de 2,5 centmetros (uma polegada) de distncia do corpo quando da transmisso. importante manter o rdio a uma distncia adequada uma vez que a exposio RF diminui ao se aumentar a distncia at a antena. Use somente antenas, baterias e acessrios fornecidos pela Motorola ou componentes de reposio aprovados pela Motorola. Caso se utilize antenas, baterias ou acessrios no aprovadas pela Motorola, corre-se o risco de exceder os limites de exposio energia de radiofreqncia estabelecidos pela FCC. Para obter a lista de antenas, baterias e demais acessrios aprovados pela Motorola, visite o seguinte website:
http://www.motorola.com/cgiss/index.shtml Para obter informaes adicionais sobre os requisitos de exposio ou sobre capacitao, visite: http://www.motorola.com/rfhealth. 5 Portugus Interferncia e compatibilidade eletromagntica NOTA: Quase todos os dispositivos eletrnicos so susceptveis interferncia eletromagntica (EMI) se no estiverem devidamente blindados ou se no tiverem sido projetados ou configurados de maneira a serem compatveis com estes tipos de sinais eletromagnticos. Edificaes Para evitar problemas de interferncia e/ou compatibilidade eletromagntica, desligue o rdio em todos os locais onde houver avisos instruindo neste sentido. Por exemplo, os hospitais e estabelecimentos de assistncia mdica podem estar utilizando equipamentos sensveis energia de RF externa. Aeronaves Quando estiver a bordo de uma aeronave, desligue o rdio quando for solicitado a faze-lo. Quando estiver utilizando o rdio, proceda em conformidade com os regulamentos da companhia area e segundo as instrues da tripulao. Dispositivos mdicos Marca-passos A Associao de Tecnologia Mdica Avanada (AdvaMed, Advanced Medical Technology Association) recomenda que se mantenha uma distncia mnima de 15 centmetros (6 polegadas) entre um rdio de mo sem fio e um marca-passo. Estas recomendaes so consistentes com as disposies da agncia norte-
americana para o controle de alimentos e medicamentos (FDA, Food and Drug Administration). Portugus 6 As pessoas que utilizam marca-passo devem seguir as recomendaes descritas a seguir:
Manter SEMPRE o rdio a uma distncia mnima de 15 centmetros (6 polegadas) do marca-passo quando o rdio estiver ligado. No carregar o rdio dentro do bolso da camisa. Utilizar o ouvido oposto ao marca-passo para minimizar a possibilidade de interferncia. Desligar o rdio imediatamente se houver suspeita de que o mesmo esteja produzindo interferncia. Dispositivos de audio Alguns rdios digitais sem fio podem interferir com certos dispositivos de audio. No caso de ocorrer interferncia, pode-se consultar o fabricante do dispositivo para obter possveis alternativas. Outros dispositivos mdicos Caso esteja utilizando qualquer outro dispositivo mdico, consulte o fabricante do dispositivo para determinar se o mesmo se encontra adequadamente protegido contra a energia de RF externa. Seu mdico poder lhe auxiliar na obteno desta informao. Segurana ao dirigir Consulte as leis e regulamentos de trnsito referentes ao uso de rdios nos locais em que estiver dirigindo. Obedea sempre estas leis. Quando estiver utilizando o rdio ao dirigir:
Preste ateno ao volante quando estiver dirigindo. Use a funo de mos livres, se este recurso estiver disponvel. Saia da pista e estacione antes de fazer ou receber uma chamada, se as condies de trnsito assim o exigirem. 7 Portugus
ADVERTNCIA Advertncias operacionais Veculos com airbag No coloque um rdio porttil sobre um airbag nem na rea prxima expanso do mesmo. O airbag se expande com grande intensidade. Se houver um rdio porttil na rea de expanso do airbag quando da expanso do mesmo, o rdio poder ser lanado com grande velocidade e causar leses graves aos passageiros. Ambientes potencialmente explosivos Desligue o rdio quando estiver em um ambiente potencialmente explosivo, exceto se estiver utilizando um tipo de rdio porttil especificamente classificado como "intrinsecamente seguro" (por exemplo, pela Factory Mutual Research Corp., CSA, UL ou CENELEC) para uso em tais reas. No remova, no instale nem carregue baterias nestas reas de risco. As fascas lanadas em ambientes potencialmente explosivas podem causar uma exploso ou incndio e resultar em leses graves ou inclusive fatais. Dentre os ambientes potencialmente explosivos mencionados anteriormente, esto as reas com combustveis situadas, por exemplo, na parte inferior de embarcaes, instalaes de transferncia e armazenamento de combustveis ou de produtos qumicos, e reas onde o ar possa conter produtos qumicos ou partculas tais como gros, poeira comum ou poeira metlica. As reas com ambientes potencialmente explosivos geralmente contm avisos de advertncia, embora nem sempre seja assim. reas de detonao e exploso Para evitar uma possvel interferncia com as operaes de detonao, desligue o rdio quando estiver prximo de detonadores eltricos, em reas de detonao ou onde houver avisos indicando para desligar os rdios bidirecionais. Siga todos os avisos e instrues. Portugus 8 Precaues operacionais
Precauo Antenas No utilize rdios portteis que estejam com a antena danificada. Se uma antena danificada entrar em contato com a pele, poder produzir uma pequena queimadura. Baterias Todas as baterias podem causar danos materiais, leses ou queimaduras se um material condutor, como por exemplo jias, chaves ou chaveiros metlicos entrar em contato com os terminais expostos. O material pode fechar um circuito eltrico (curto-circuito) e ficar muito aquecido. Manuseie as baterias com cuidado, especialmente quando estiver carregando-as no bolso, na bolsa ou em algum outro objeto pessoal que contenha objetos metlicos. 9 Portugus Informaes sobre rdios intrinsecamente seguros Equipamento aprovado pela FMRC Recomenda-se que toda pessoa que se proponha a utilizar um rdio em locais com concentraes perigosas de substncias inflamveis (atmosferas de risco) procure se familiarizar primeiro com o tema da segurana intrnseca e com o Artigo 500 (locais [classificados] perigosos) do Cdigo Eltrico Nacional do EUA
(National Electrical Code), tambm conhecido como NFPA 70, publicado pela Associao Nacional de Proteo Contra Incndios dos EUA (National Fire Protection Association). A Guia de Aprovao FMRC, publicada pela Factory Mutual Research Corporation (FMRC), inclui uma lista de fabricantes e de produtos aprovados pela FMRC para uso nas referidas reas. Da mesma forma, a FMRC publicou uma norma de aprovao voluntria para estabelecimentos de servios de reparos
("nmero de classe 3605"). Foram afixadas etiquetas de aprovao no rdio que identificam a unidade como aprovada pela FMRC para as atmosferas de risco especificadas. Nas referidas etiquetas se estabelece o nmero de pea da bateria que se deve utilizar, bem como a classe, diviso e grupo correspondentes. De acordo com o desenho da unidade porttil, a etiqueta da FMRC poder estar localizada na parte posterior ou no chassis do rdio. O selo de aprovao da FMRC idntico ao mostrado aqui. FM APPROVED Portugus 10
ADVERTNCIA Equipamentos de radiocomunicao no devem ser colocados em funcionamento estando em atmosferas de risco, exceto se tais equipamentos contarem com as aprovaes especiais correspondentes (por exemplo, a aprovao da FMRC). Caso contrrio, poder resultar em incndio ou exploses. Um produto aprovado pela FMRC no deve ser colocado em funcionamento em uma atmosfera de risco se o referido produto apresentar sinais de danos fsicos (por exemplo, fraturas em sua estrutura externa). Caso contrrio, poder resultar em incndio ou exploses. No troque nem reinstale as baterias em atmosferas de risco. As pequenas fascas produzidas quando da insero ou retirada das baterias podero causar incndios ou exploses.
ADVERTNCIA No troque nem reinstale acessrios em atmosferas de risco. As pequenas fascas produzidas quando da insero ou retirada dos acessrios podero causar incndios ou exploses. Desligue o rdio antes de desinstalar ou de instalar baterias ou acessrios. No desmonte a unidade aprovada pela FMRC de forma que seus circuitos internos possam ficar expostos. 11 Portugus Os rdios devero ser enviados pela fbrica da Motorola com o recurso de segurana intrnseca para o funcionamento em atmosferas de risco e a etiqueta de aprovao da FMRC. As unidades no podem ser "atualizadas" com este recurso sem serem marcadas com as etiquetas correspondentes no campo. Toda modificao ir alterar a configurao do projeto original dos componentes da unidade. As modificaes somente podero ser realizadas pelo fabricante do produto original em uma fbrica autorizada pela FMRC.
ADVERTNCIA O uso de um produto aprovado pela FMRC com uma bateria no aprovada pela FMRC ou com um acessrio no aprovado pela FMRC (ou no aprovado para uso com o produto) poder dar lugar a uma condio de risco semelhante quela produzida ao se utilizar uma combinao de rdio no aprovada pela FMRC em uma rea de risco. Toda modificao incorreta ou no autorizada de um produto aprovado pela FMRC tornar nula a aprovao do produto. Reparos de produtos aprovados pela FMRC O REPARO DE PRODUTOS MOTOROLA APROVADOS PELA FMRC DE RESPONSABILIDADE DO USURIO. O usurio no dever reparar nem trocar a etiqueta de nenhum equipamento de comunicao fabricado pela Motorola que tenha a etiqueta de aprovao da FMRC ("FMRC Approved Product" [produto aprovado pela FMRC]) exceto se estiver habilitado a efetuar reparos e servios em conformidade com as normas atuais de aprovao da FMRC ("nmero de classe 3605"). Portugus 12 Recomenda-se procurar os estabelecimentos de reparos que contam com a aprovao de servios de reparo 3605.
ADVERTNCIA Toda reposio de etiquetas ou reparo incorreto de qualquer produto aprovado pela FMRC poder afetar negativamente a classificao da unidade. O uso de um rdio que no seja intrinsecamente seguro em atmosferas de risco poder acarretar leses graves ou mesmo fatais. A norma de aprovao FMRC com nmero de classe 3605 est sujeita a alteraes a qualquer momento em notificao prvia. Sugerimos solicitar junto FMRC uma cpia atualizada da norma 3605. Na mencionada norma 3605, publicada em dezembro de 1994, esto includas as definies e requisitos de servio conforme descrito a seguir:
Reparo Um reparo consiste em algo realizado no interior da unidade com a finalidade de reconstituir sua condio original, aprovada pela FMRC. Tal reparo deve ser realizado em um estabelecimento de reparos aprovado pela FMRC. No so considerados reparos aquelas aes para as quais no seja necessrio abrir a cobertura exterior da unidade de forma que os circuitos eltricos internos da unidade fiquem expostos. Este procedimento no necessita ser realizado em um estabelecimento aprovado pela FMRC. 13 Portugus Substituio de etiquetas O estabelecimento de reparos dever dispor de um sistema por meio do qual se controle a substituio das etiquetas de aprovao da FMRC, de modo a garantir que toda reposio de etiqueta seja realizada unicamente em unidades que foram adquiridas originalmente junto ao fabricante com a referida etiqueta de aprovao da FMRC. O estabelecimento de reparos no dever manter estoques de etiquetas de aprovao da FMRC. Cada vez que for necessrio, dever ser solicitada uma etiqueta de aprovao da FMRC junto ao fabricante original para fins de reparo em uma unidade especfica. As etiquetas de substituio podero ser obtidas e fixadas junto unidade pelo prprio estabelecimento de reparos, uma vez que se tenha evidncias suficientes de que a unidade na qual ser feita a substituio da etiqueta se trata de uma unidade originalmente aprovada pela FMRC. Para a verificao se exige, embora no exclusivamente, uma unidade danificada com uma etiqueta FMRC, uma unidade com a cobertura danificada que exiba a etiqueta FMRC ou uma fatura do cliente indicando o nmero de srie da unidade e a compra de um modelo aprovado pela FMRC. No substitua os itens opcionais nem os acessrios Os equipamentos de comunicaes da Motorola certificados pela Factory Mutual Research Corporation so testados em nvel de sistema e so compostos de uma unidade porttil aprovada pela FMRC, uma bateria aprovada pela FMRC, e componentes opcionais e/ou acessrios aprovados todos eles pela FMRC. O uso desta combinao aprovada pela FMRC de unidade porttil e bateria dever ser estritamente observado. No se deve utilizar componentes substitutos, mesmo quando o elemento substituto tenha sido previamente aprovado para o uso com outros equipamentos de comunicaes da Motorola. As configuraes aprovadas aparecem no manual de produtos aprovados pela Factory Mutual Research Corporation que vem includo junto com o rdio. Portugus 14 Normes de scurit et exposition lnergie de RF pour lutilisation des radios bidirectionnelles portatives
Attention AVANT DUTILISER LA RADIO, LISEZ CETTE BROCHURE QUI CONTIENT UN MODE DEMPLOI IMPORTANT SUR SON UTILISATION SCURITAIRE ET POUR OBTENIR DES INFORMATIONS RELATIVES LNERGIE DE RF ET SON CONTRLE AFIN DE VRIFIER LA CONFORMIT DES LIMITES DEXPOSITION LNERGIE DE RF TABLIES PAR LES NORMES NATIONALES ET INTERNATIONALES EN VIGUEUR. Les informations contenues dans ce document annulent les informations gnrales de scurit des manuels de lutilisateur publis avant fvrier 2002. Si les radios ont t approuves pour leur scurit intrinsque, lisez les instructions et les informations sur la scurit intrinsque contenues dans la page 10 de cette brochure. Conformit aux normes dexposition lnergie de RF AVIS :
Cette radio est prvue pour tre utilise dans les applications professionnelles ou contrles o les utilisateurs ont t avertis du danger potentiel de lexposition et peuvent en contrler le risque. Ce dispositif radio nest PAS autoris pour la vente au public en gnral et au march libre des consommateurs. 1 Franais Rglements du conseil fdral amricain des communications (FCC) Le FCC a tabli des limites sur les risques dexposition aux missions de frquence radio (RF) partir des radios bidirectionnelles portatives. Le FCC exige que les fabricants dmontrent que les radios bidirectionnelles portatives soient conformes aux limites dexposition lnergie de RF pour pouvoir tre commercialises sur le march des tats-Unis. Lorsque les radios bidirectionnelles sont approuves pour des limites dexposition lnergie en ce qui concerne les environnements professionnels ou contrls, le FCC exige que les utilisateurs soient totalement conscients du danger potentiel de lexposition et soient en mesure den contrler le risque. La prise de conscience et le contrle de lexposition lnergie de RF peuvent tre accomplis en utilisant des tiquettes ou bien grce lducation ou la formation par le biais de moyens appropris, comme, par exemple, les informations et les instructions contenues dans les guides de lutilisateur ou dans les brochures de scurit. Votre radio bidirectionnelle Motorola porte une tiquette informative dexposition lnergie de RF dans le compartiment de la batterie. Cette brochure de scurit contient des informations sur lexposition lnergie de RF ainsi que des instructions utiles sur la faon de contrler cette exposition. Cette radio bidirectionnelle Motorola a t conue et teste afin de garantir sa compatibilit avec les normes et recommandations nationales et internationales ci-dessous lies lexposition des tres humains lnergie lectromagntique de RF : Cette radio respecte les limites dexposition tablies par le IEEE
(FCC) et la ICNIRP pour les environnements professionnels ou avec contrle dexposition lnergie de RF, des cycles de travail allant jusqu 50 % (50 % transmission / 50 % rception). En ce qui concerne la mesure de lnergie de RF pour valuer sa conformit aux normes dexposition du FCC, la radio met de lnergie de RF mesurable seulement lorsquelle est en cours dmission (conversation), et non pas lorsquelle reoit (coute) ni quand elle est au repos. Franais 2 REMARQUE :Les batteries agres, fournies pour cette radio, supportent un cycle de travail de 5-5-90 (5% du temps en transmission5% en rception90% au repos), mme si la radio respecte les limites dexposition professionnelle du FCC des cycles de travail allant jusqu 50 %. Cette radio bidirectionnelle Motorola rpond aux normes et recommandations suivantes relatives lexposition lnergie de RF :
Conseil fdral amricain des communications (FCC), Code de rglements fdraux ; 47CFR partie 2 section J. Organisme de normalisation amricain (ANSI) / Institut des ingnieurs en lectricit et en lectronique (IEEE) C95. 1-1992. Institut des ingnieurs en lectricit et en lectronique (IEEE) (C95.1-dition 1999). Comit international pour la protection contre les radiations non ionisantes
(ICNIRP) 1998. Ministre de la sant (Canada), Code de scurit 6. Limites dexposition humaine aux champs lectromagntiques de radiofrquence sur la plage de frquences allant de 3 kHz 300 GHz (1999). Direction australienne de communications, norme de radiocommunications 2001 (exposition humaine au rayonnement lectromagntique). ANATEL, Entit de rgulation du Brsil, Rsolution 256 (11 avril 2001) exigences supplmentaires pour la certification des produits RMS, cellulaires et fibre optique PCS . 3 Franais Directives de contrle et de conformit et mode demploi des radios bidirectionnelles portatives Pour contrler votre exposition et garantir la conformit aux limites dexposition lnergie des environnements professionnels et contrls, toujours observer les procdures suivantes :
Ne pas mettre plus de 50% du temps. Pour mettre (parler) appuyez sur le bouton de transmission (PTT). Pour recevoir les appels, relchez le bouton de transmission (PTT). Il est important de ne pas transmettre plus de 50% du temps tant donn que la radio produit une importante exposition lnergie de RF seulement pendant lmission (en termes de conformit aux normes de mesure). Maintenez la radio en position verticale face au visage et placez le microphone (ainsi que les autres parties de la radio, antenne comprise) une distance dau moins 2,5 5 centimtres (un deux pouces) des lvres. Il est important de garder la radio une distance convenable tant donn que les expositions lnergie de RF diminuent proportionnellement l'augmentation de la distance de l'antenne. Pour le fonctionnement de lunit ajuste au corps, toujours placez la radio dans une attache, un support, une housse, un tui ou un harnais de scurit agr Motorola pour ce produit. Toutes combinaisons daccessoires, dantennes et de dispositifs autorises par Motorola sont conformes aux limites dexposition lnergie de RF tablies par le FCC pour les environnements professionnels ou contrls. Les renseignements au sujet de lexposition de diffrentes combinaisons daccessoires, dantennes et de dispositifs sont disponibles dans la section Display Exhibits du site Internet http://www.fcc.gov/oet/fccid, aprs avoir fait une requte en se servant du numro didentification FCC, que lon retrouve sur ltiquette de son radio. Si lon utilise des accessoires non agrs Motorola, on risque de dpasser les limites Franais 4 dexposition lnergie de RF pour des environnements professionnels ou contrls, tablies dans les recommandations du FCC. Si vous nutilisez pas daccessoires ajusts au corps et que vous utilisez la radio dans la position habituelle face au visage, noubliez pas de maintenir lantenne et la radio une distance minimale de 2,5 centimtres
(un pouce) du corps lors de la transmission. Il est important de garder la radio une distance convenable tant donn que les expositions lnergie de RF diminuent proportionnellement l'augmentation de la distance de l'antenne. Utilisez uniquement les antennes, les batteries et les accessoires fournis ou de rechange agrs Motorola. En utilisant des antennes, des batteries ou des accessoires non agrs Motorola vous risquez de dpasser les limites dexposition lnergie de RF tablies dans les recommandations du FCC. Pour trouver une liste dantennes, de batteries et dautres accessoires agrs Motorola, visitez le site Web suivant, o vous pouvez trouver une liste des accessoires dhomologation :
http://www.motorola.com/cgiss/index.shtml Pour davantage de renseignements sur les exigences dexposition ou dautres informations de formation, visitez le site :
http://www.motorola.com/rfhealth. 5 Franais Interfrence et compatibilit lectromagntique REMARQUE :Presque tous les dispositifs lectroniques sont sensibles leffet lectromagntique perturbateur (EMI) sils ne sont pas convenablement protgs ou sils ne sont pas conus ou configurs de telle sorte quils soient compatibles avec ce type de signaux lectromagntiques. tablissements Afin dviter des problmes dinterfrence et/ou de compatibilit lectromagntique, teignez la radio dans tous les tablissements o des panneaux daffichage vous invitent le faire. Il se peut, par exemple, que les hpitaux et les tablissements de sant utilisent des appareils sensibles lnergie de RF externe. Aronefs Lorsque vous vous trouvez bord dun avion, teignez la radio lorsque vous tes invit le faire. Toute utilisation de la radio doit se faire conformment aux rglements en vigueur de la compagnie arienne et sur instructions de lquipage. Dispositifs mdicaux Stimulateurs cardiaques LAssociation de technologie mdicale avance (AdvaMed, Advanced Medical Technology Association) recommande de conserver une distance minimale de 15 centimtres (6 pouces) entre une radio portable sans fil et un stimulateur cardiaque. Ces recommandations concordent avec les dispositions de la Fdration amricaine des aliments et drogues (FDA, Food and Drug Administration). Franais 6 Les personnes utilisant des stimulateurs cardiaques doivent suivre les recommandations suivantes :
TOUJOURS maintenir la radio une distance minimale de 15 centimtres
(6 pouces) du stimulateur cardiaque lorsquelle est allume. Ne pas porter la radio dans la poche-portefeuille. Utiliser loreille oppose au stimulateur cardiaque afin de rduire au maximum le risque dinterfrence. teindre la radio immdiatement si vous souponnez la prsence dune interfrence quelconque. Aides auditives Certaines radios numriques sans fil peuvent interfrer avec certaines aides auditives. En cas dinterfrence, il est prfrable de consulter le fabricant de laide auditive afin de chercher des solutions de remplacement. Autres dispositifs mdicaux Si vous utilisez tout autre dispositif mdical, consultez le fabricant du dispositif afin de dterminer sil est convenablement protg contre lnergie de RF externe. Votre mdecin peut vous aider obtenir cette information. Scurit lors de la conduite Consultez la lgislation et les rglements en vigueur sur lutilisation des radios dans les zones o vous conduisez. Respectez toujours ces rgles. Lorsque vous utilisez la radio en conduisant :
Concentrez toute votre attention sur la route et sur votre conduite. Utilisez le mode mains libres, si vous y avez accs. Rangez-vous sur le bas-ct et stationnez votre vhicule avant de faire ou de rpondre un appel, si les conditions de conduite lexigent. 7 Franais Avertissements relatifs au fonctionnement
AVERTISSEMENT Vhicules quips de sac(s) gonflable(s) vitez de placer une radio portable au-dessus dun sac gonflable ou dans la zone de dploiement de ce dernier. Les sacs gonflables se dploient avec une force considrable. Si une radio portable se trouve dans la zone de dploiement du sac lorsque celui-ci se gonfle, la radio peut tre propulse avec une force considrable et risque alors doccasionner de graves lsions corporelles aux passagers. Atmosphres potentiellement explosives teignez la radio avant de pntrer dans une atmosphre potentiellement explosive, moins que vous nutilisiez une radio portable spcialement classifie scurit intrinsque (par exemple, par la Factory Mutual Research Corp., CSA, UL ou CENELEC) pour une utilisation dans ce type de zones. vitez de retirer, dinstaller ou de charger des batteries dans ces zones. Les tincelles dans des atmosphres potentiellement explosives peuvent provoquer une explosion ou un incendie et entraner des lsions corporelles voire mme mortelles. Parmi les zones potentiellement explosives mentionnes plus haut, citons les zones davitaillement en carburant, par exemple la cale des bateaux, les installations de transfert et de stockage de carburant ou de produits chimiques et les zones dans lesquelles lair est charg en produits chimiques ou en particules telles que de la poudre de crales, de la poussire ou de la poudre mtallique. Les zones atmosphres potentiellement explosives affichent gnralement, mais pas toujours, des panneaux de mise en garde. Dtonateurs et zones de dynamitage Afin dviter une ventuelle interfrence avec les oprations de dtonation, teignez la radio proximit de dtonateurs lectriques, dans une zone de dtonations ou l o sont affichs des panneaux indiquant dteindre les radios bidirectionnelles. Respectez tous les panneaux et toutes les instructions. Franais 8 Prcautions demploi
Attention Antennes vitez dutiliser une radio portable si son antenne est endommage. Le contact dune antenne endommage avec la peau peut provoquer une lgre brlure. Batteries Toutes les batteries peuvent occasionner des dommages matriels, des lsions ou des brlures si un matriel conducteur comme des bijoux, des cls ou des chanettes perles entrent en contact avec les bornes exposes. Le matriel conducteur risque de fermer le circuit lectrique (court-circuit) et de devenir trs chaud. Manipulez avec prcaution les batteries charges, en particulier lorsque vous les portez dans une poche, un sac main ou tout autre rcipient contenant des objets mtalliques. 9 Franais Informations sur les radios scurit intrinsque Appareil agr FMRC Nous recommandons toute personne envisageant lutilisation dune radio dans un local comportant des concentrations dangereuses de matires inflammables
(atmosphre dangereuse) de se familiariser avec le thme de la scurit intrinsque, et avec larticle 500 (locaux [classifis] dangereux) du Code lectrique amricain (National Electrical Code), galement connu sous le nom de NFPA 70, que publie lassociation amricaine pour la protection contre lincendie
(National Fire Protection Association). Le guide dhomologation FMRC, publi par la Factory Mutual Research Corporation (FMRC), comprend une liste de fabricants et de produits agrs FMRC pour lesdits locaux. Par ailleurs, la FMRC a publi une norme dhomologation volontaire pour centres de rparation ( numro de classe 3605 ). Des tiquettes ont t apposes sur la radio afin dindiquer lhomologation de lunit auprs de la FMRC pour les atmosphres dangereuses spcifies. Ltiquette spcifie la catgorie de risque laquelle la batterie correspond (Classe/Division/Groupe), ainsi que le numro de rfrence qui doit tre utilise avec cet appareil. Selon le modle dunit portable, ltiquette de la FMRC peut se trouver sur la partie arrire ou infrieure du botier de la radio. La marque dhomologation FMRC est illustre ci-
contre. FM APPROVED Franais 10
AVERTISSEMENT vitez de faire fonctionner des quipements de radiocommunications dans des atmosphres dangereuses, moins que ces derniers ne possdent les homologations spciales correspondantes (par exemple, lhomologation par la FMRC). Vous risquez sinon de provoquer une explosion ou un incendie. vitez de faire fonctionner un produit agr FMRC dans une atmosphre dangereuse si celui-ci a t endommag (si, par exemple, son botier est fissur). Vous risquez sinon de provoquer une explosion ou un incendie. vitez de remplacer ou de rinstaller des batteries dans une atmosphre dangereuse. Si des tincelles se produisent lors de linstallation ou lors de lextraction des batteries, cela peut provoquer un incendie ou une explosion.
AVERTISSEMENT vitez de remplacer ou de rinstaller des accessoires dans une atmosphre dangereuse. Si des tincelles se produisent lors de linstallation ou lors de lextraction des accessoires, cela peut provoquer un incendie ou une explosion. teignez la radio avant de retirer ou dinstaller toute batterie ou accessoire. vitez de dmonter une unit agre FMRC, afin de ne pas en exposer les circuits lectriques intgrs. 11 Franais Les radios doivent tre expdies par lusine Motorola avec aptitude fonctionner dans des atmosphres dangereuses et porter ltiquette dhomologation de la FMRC. Les radios ne peuvent pas tre mises niveau cette capacit ni porter des tiquettes correspondant cette catgorie. Toute modification changera la configuration dorigine du modle des composants de lunit. Les modifications ne peuvent tre effectues que par le fabricant du produit dorigine dans les tablissements industriels vrifis par la FMRC.
AVERTISSEMENT Lutilisation dun produit agr FMRC avec une batterie ou des accessoires non agrs FMRC (ou non approuvs pour tre utiliss avec ce produit) peut gnrer des conditions dangereuses assimilables celles que crerait lutilisation combine dune radio non agre FMRC dans un endroit dangereux. Toute modification incorrecte ou non autorise dun produit agr FMRC annule lhomologation du produit. Franais 12 Rparation de produits agrs FMRC LA RPARATION DE PRODUITS MOTOROLA AGRS FMRC INCOMBE LUTILISATEUR. Lutilisateur ne doit ni rparer ni changer ltiquette daucun appareil de communication fabriqu par Motorola portant une tiquette dhomologation de la FMRC ("FMRC Approved Product" [produit agr FMRC]), moins dtre habilit effectuer des rparations et lentretien conformment aux normes actuelles dhomologation FMRC ( numro de classe 3605 ). Il est recommand dutiliser un centre de rparation qui opre sous lhomologation de service de rparation 3605.
AVERTISSEMENT Toute rparation ou remplacement dtiquette incorrect sur un produit quelconque agr FMRC peut compromettre lhomologation de lunit. Lutilisation dans une atmosphre dangereuse dune radio ne rpondant pas aux normes de scurit intrinsque peut occasionner des lsions graves, voire mortelles. Les normes dhomologation FMRC numro de classe 3605 sont tout moment sous rserve de modifications sans pravis. Il est suggr de demander la FMRC une copie actuelle de la norme 3605. Dans la publication de la norme 3605 de dcembre 1994, on trouve des dfinitions-cls et des exigences dentretien comme suit :
Rparation Une rparation consiste effectuer une modification lintrieur de lunit afin quelle retrouve sa condition dorigine, agre FMRC. Ladite rparation doit tre ralise dans un centre de rparation agr FMRC. 13 Franais Ne sont pas considres comme des rparations, les modifications effectues sans quil soit ncessaire douvrir le botier externe de lunit de telle sorte que ses circuits lectriques intgrs soient exposs. Ces modifications ne doivent pas ncessairement tre ralises dans un centre de rparation agr FMRC. Remplacement des tiquettes Le centre de rparation doit tre quip dun systme permettant de contrler le remplacement des tiquettes dhomologation de la FMRC, afin dtre sr que tout remplacement dtiquettes se ralise exclusivement sur des units qui ont lorigine t envoyes par le fabricant avec ltiquette dhomologation de la FMRC. Le centre de rparation ne doit pas conserver dinventaires des tiquettes dhomologation de la FMRC. Le cas chant, une tiquette dhomologation de la FMRC doit tre sollicite auprs du fabricant dorigine pour rparer une unit spcifique. Les tiquettes de remplacement peuvent tre obtenues et apposes sur lunit par le centre de rparation, une fois dment prouv que lunit dont ltiquette va tre remplace tait lorigine une unit agre FMRC. La vrification peut inclure, sans y tre limite, une unit dont ltiquette dhomologation est abme, une unit avec un botier dfectueux portant une tiquette dhomologation ou une facture client indiquant le numro de srie de lunit et lachat dun modle agr FMRC. vitez dinterchanger les options ou les accessoires Les appareils de communications Motorola certifis par la Factory Mutual Research Corporation sont tests au niveau systme. Ils comprennent une unit portable agre FMRC, une batterie agre FMRC et des composants optionnels et/ou des accessoires qui sont tous agrs FMRC. Cette combinaison unit portable-batterie agre FMRC doit tre strictement respecte. Aucun composant de substitution ne doit tre utilis mme sil a pralablement t agr pour une utilisation avec un autre appareil de communications Motorola. Les configurations agres sont rpertories dans la liste des produits FMRC qui est inclue avec la radio. Franais 14
1 | Stuffer for User Manual | Users Manual | 370.50 KiB |
Stuffer_1.fm Page 1 Wednesday, July 8, 2009 11:16 AM m Manual revision 6875945M01-A ASTRO APX 7000 User Guide This revision outlines changes that have occurred since the printing of your manual. Use this information to supplement your manual. REVISION CHANGE:
Please use the following information to supplement your existing User Guide. The table that follows lists the pages attached to this PMR and their related pages. Section Title Antennas Description Added four new antenna models to the list, namely PMAS4000_, PMAE4065_, PMAT4000_ and PMAT4001_. Added footnotes. Batteries and Battery Accessories Added two accessories, namely NNTN7034_ and Section Accessories Accessories Accessories Page 105 105 105 106 107 Carry Accessories Accessories Audio Accessories NNTN7033_. Changed Belt Clip Kit, 2.5", Plastic (Compatible with Clamshell Batteries) (NTN8266_) to 2.5" Belt Clip
(NTN8266_). Added a phrase 700/800 MHz band radio only, to accessories PMMN4059_, PMMN4060_ and PMMN4061_. Added four new accessories to the list, namely RLN6424_, PMLN5101_, PMMN4065_ and HMN4104_. 2009 by Motorola, Inc. All Rights Reserved. 7/09 1301 E. Algonquin Rd., Schaumburg, IL 60196-1078, U.S.A.
*PMR151*
PMR151 English Stuffer_1.fm Page 2 Wednesday, July 8, 2009 11:16 AM Accessories Antennas 800 MHz, GPS Antenna (NAF5085_)2,3 700/800 MHz, VHF GPS Antenna (NAR6591_)2,3 GPS Antenna (NAG4000_) UHF (380 520 MHz), 700/800 MHz, GPS (PMAS4000_)1,3 UHF (380 520 MHz), GPS (PMAE4065_)1 VHF Low (136 168 MHz), UHF (380 470 MHz), GPS
(PMAT4000_)1,2 VHF High (155 174 MHz), UHF (380 470 MHz), GPS
(PMAT4001_)1,2 1 This antenna is not campatible with VHF/700/800 dual band radio. 2 This antenna is not compatible with UHF/700/800 dual band radio. 3 This antenna is not compatible with VHF/UHF dual band radio. Batteries and Battery Accessories 2000 mAh, IMPRESTM NiMH (FM), IP57 Rugged
(NNTN7035_) 2000 mAh, IMPRES NiMH (FM), IP57 (NNTN7036_) 105 English 2100 mAh, IMPRES NiMH (Standard), IP57 (NNTN7037_) 2500 mAh, IMPRES Li-Ion, IP57 (NNTN7038_) 2100 mAh, IMPRES NiMH (Standard), IP57 Rugged
(NNTN7573_) 4000 mAh, IMPRES Li-Ion (Standard) (NNTN7034_) 3900 mAh, IMPRES Li-Ion (FM) (NNTN7033_) Carry Accessories Belt Clips
3" Belt Clip, Plastic (HLN6875_) 2.5" Belt Clip (NTN8266_) Belt Loops
2.5" Swivel Belt Loop (PMLN5407_) 2.75" Replacement Swivel Belt Loop (PMLN5408_) 3" Swivel Belt Loop (PMLN5409_) Carry Cases
Nylon Carry Case with 3 Fixed Belt Loop and T-Strap, for Short Radio (PMLN5322_) Stuffer_1.fm Page 3 Wednesday, July 8, 2009 11:16 AM Hard Leather Carry Case with 3 Fixed Belt Loop, D-Rings, and T-Strap, for Short Radio (PMLN5323_) Hard Leather Carry Case (High Activity) with 2.75 Swivel Belt Loop, D-Rings, and T-Strap, for Short Radio
(PMLN5324_) Nylon Carry Case with 3 Fixed Belt Loop and T-Strap, for Long Radio (PMLN5328_) Hard Leather Carry Case with 3 Fixed Belt Loop, D-Rings, and T-Strap, for Long Radio (PMLN5329_) Hard Leather Carry Case (High Activity) with 2.75 Swivel Belt Loop, D-Rings, and T-Strap, for Long Radio
(PMLN5330_) Carry Strap (NTN5243_) Carry Holder, Basic (PMLN5331_) Chargers IMPRES Single-Unit (US Plug) (NNTN7080_) IMPRES Single-Unit (Euro Plug) (NNTN7081_) IMPRES Single-Unit (UK Plug) (NNTN7082_) IMPRES Single-Unit (Aust, NZ Plug) (NNTN7083_) IMPRES Single-Unit (Argentina Plug) (NNTN7084_) IMPRES Single-Unit (US Plug, Euro User Guide)
(NNTN7085_) IMPRES Single-Unit (Korean Plug) (NNTN7261_) IMPRES Multi-Unit, Display (Aust, NZ Plug) (NNTN7063_) IMPRES Multi-Unit, Display (US Plug) (NNTN7073_) IMPRES Multi-Unit, Display (UK Plug) (NNTN7074_) IMPRES Multi-Unit, Display (Argentina Plug) (NNTN7075_) IMPRES Multi-Unit, Display (US Plug, Euro User Guide)
(NNTN7076_) IMPRES Multi-Unit, Display (Korean Plug) (NNTN7077_) IMPRES Multi-Unit, Display (Euro Plug) (NNTN7086_) IMPRES Multi-Unit, Non-Display (US Plug) (NNTN7065_) IMPRES Multi-Unit, Non-Display (Euro Plug) (NNTN7066_) IMPRES Multi-Unit, Non-Display (UK Plug) (NNTN7067_) IMPRES Multi-Unit, Non-Display (Aust, NZ Plug)
(NNTN7068_) IMPRES Multi-Unit, Non-Display (Argentina Plug)
(NNTN7069_) IMPRES Multi-Unit, Non-Display (US Plug, Euro User Guide) (NNTN7070_) IMPRES Multi-Unit, Non-Display (Korean Plug)
(NNTN7071_) 106 English Stuffer_1.fm Page 4 Wednesday, July 8, 2009 11:16 AM Audio Accessories Small Remote Speaker Microphone, IP54, 3.5 mm Jack, Receive Only (PMMN4024_) Small Remote Speaker Microphone, IP54, 3.5 mm Jack
(PMMN4025_) Noise Canceling Remote Speaker Microphone, IP54, 3.5 mm Jack (PMMN4062_) Public Safety Microphone, 700/800 MHz band radio only, 18 inch, IP55, 3.5 mm Jack (PMMN4059_) Public Safety Microphone, 700/800 MHz band radio only, 24 inch, IP55, 3.5 mm Jack (PMMN4060_) Public Safety Microphone, 700/800 MHz band radio only, 30 inch, IP55, 3.5 mm Jack (PMMN4061_) Heavy-Duty Headset (PMLN5275_) Lightweight Headset (RMN5058_) Earbud for Remote Speaker Microphone, 3.5 mm Jack, Short Coiled Cable, Receive Only (RLN4885_) Earpiece with Translucent Tube for Remote Speaker Microphone, 3.5 mm Jack, Short Coiled Cable, Receive Only
(RLN4941_) Ear Receiver for Remote Speaker Microphone, 3.5 mm Jack, Short Coiled Cable, Receive Only (WADN4190_) 1-Wire, Receive Only Earpiece, Black (RLN5878_) 107 English 1-Wire, Receive Only Earpiece, Beige (RLN5879_) 2-Wire, One Programmable Button, Black (RLN5880_) 2-Wire, One Programmable Button, Beige (RLN5881_) 2-Wire with Translucent Tube, One Programmable Button, Black (RLN5882_) 2-Wire with Translucent Tube, One Programmable Button, Beige (RLN5883_) 3-Wire with Translucent Tube, One Programmable Button, Black (PMLN5111_) 3-Wire with Translucent Tube, One Programmable Button, Beige (PMLN5112_) Low Noise Kit (RLN5886_) High Noise Kit (RLN5887_) IMPRES Templer Transducer (PMLN5101_) Secondary Audio Accessory for Display Remote Speaker Microphone (RLN6424_) Standard Large IP57 Remote Speaker Microphone
(PMMN4065_) IMPRES Display GCAI Submersible Remote Speaker Microphone with Jack and Channel Selector (HMN4104_) Stuffer_1.fm Page 5 Wednesday, July 8, 2009 11:16 AM Notes 108 English
1 | Users Manual | Users Manual | 1.29 MiB |
m ASTRO APX 7000 Series Digital Portable Radios Quick Reference Card Product Safety and RF Exposure Compliance
Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio. ATTENTION!
This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio (Motorola Publication part number 6881095C98) to ensure compliance with RF energy exposure limits. Radio Controls Top (Orange) Button __________ 3-Position A/B/C Switch __________________ Accessory Connector Antenna Top Display Main Speaker Battery 16-Position Select Knob __________ On/Off/Volume Control Knob Top Side (Select) Button __________ PTT Button Side Button 1 __________ Side Button 2 __________ Radio On/Off 2-Position Concentric Switch ______________
On On/Off/Volume knob clockwise.
Off On/Off/Volume knob counterclockwise. Zones and Channels
Zone Zone switch to desired zone.
Channel Channel switch to desired channel. 2009 by Motorola, Inc. All Rights Reserved. 03/09 1301 E. Algonquin Rd., Schaumburg, IL 60196-1078, U.S.A. Receiving and Transmitting 1 Select zone/channel. 2 Listen for a transmission. OR Press and hold Volume Set button. OR Press Monitor button and listen for activity. 3 Adjust volume, if necessary. 4 Press the PTT button to transmit; release to receive. Sending an Emergency Alarm 1 Press the Emergency button. 2 The display shows EMERGNCY and the current zone/channel. A short, medium-
pitched tone sounds, and the LED rapidly blinks red. 3 When acknowledgment is received, you hear four beeps; alarm ends; and radio exits emergency. To exit emergency at any time, press and hold the Emergency button.
*68007024033*
68007024033-A English m On = Secure operation. Off = Clear operation. Blinking = Receiving an encrypted voice call. On steady = View mode Blinking = Program mode Aor Bor C Dor Eor F Zone Bank 1 A = Radio is in Zone 1. B = Radio is in Zone 2. C = Radio is in Zone 3. Zone Bank 2 D = Radio is in Zone 4. E = Radio is in Zone 5. F = Radio is in Zone 6. Display Status Icons U vV Blinks when the battery is low. The more stripes, the stronger the signal strength for the current site
(trunking only). Direct radio to radio communication or connected through a repeater. On = Direct Off = Repeater This channel is being monitored. L = Radio is set at Low power. H = Radio is set at High power. Scanning a scan list. Blinking dot = Detects activity on the Priority-One Channel during scan. Steady dot = Detects activity on the Priority-Two Channel during scan. The vote scan feature is enabled. O M HOR L i j k Sending an Emergency Call 1 Press the Emergency button. 2 Press and hold the PTT button. Speak clearly into the microphone. 3 Release the PTT button to end call. 4 Press and hold Emergency button to exit emergency. To exit emergency at any time, press and hold the Emergency button. Sending a Silent Emergency Call 1 Press the Emergency button. 2 The display does not change; the LED does not light up, and there is no tone. 3 Silent emergency continues until you:
Press and hold the Emergency button to exit emergency state. OR Press and release the PTT button to exit silent emergency mode and enter regular emergency (alarm, call, or alarm with call) mode. To exit emergency at any time, press and hold the Emergency button. English Declaration of Conformity This declaration is applicable to your radio only if your radio is labeled with the FCC logo shown below. DECLARATION OF CONFORMITY Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola, Inc. Address: 1301 East Algonquin Road, Schaumburg, IL 60196-1078, U.S.A. Phone Number: 1-800-927-2744 Hereby declares that the product:
Model Name: APX 7000 conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a) Class B Digital Device As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. D e c l a r a t i o n o f C o n f o r m i t y i English Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. y t i m r o f n o C f o n o i t a r a l c e D ii English Contents This User Guide contains all the information you need to use the APX 7000 Series Digital Portable Radios. Declaration of Conformity . i Important Safety Information . vii Product Safety and RF Exposure Compliance . vii Software Version . vii Computer Software Copyrights . viii Documentation Copyrights . viii Disclaimer . viii Getting Started . 1 How to Use This Guide . 1 Notations Used in This Manual . 1 What Your Dealer/System Administrator Can Tell You . 2 C o n t e n t s Preparing Your Radio for Use . 2 Charging the Battery . 3 Battery Charger . 3 Attaching the Battery . 3 Attaching the Antenna . 4 Attaching the Accessory Connector Cover . 5 Attaching the Belt Clip . 5 Turning On the Radio . 6 Adjusting the Volume . 7 Identifying Radio Controls . 7 Radio Parts and Controls . 8 Programmable Features . 9 Assignable Radio Functions . 9 Assignable Settings or Utility Functions . 10 Accessing the Preprogrammed Functions . 10 Push-To-Talk (PTT) Button . 10 Identifying Status Indicators . 11 Status Icons . 11 LED Indicator . 12 iii English Intelligent Lighting Indicators . 13 Alert Tones . 14 General Radio Operation . 17 Selecting a Zone . 17 Selecting a Radio Channel . 18 Receiving and Responding to a Radio Call . 18 Receiving and Responding to a Talkgroup Call . 19 Receiving and Responding to a Private Call (Trunking Only) . 19 Receiving and Responding to a Telephone Call (Trunking Only) . 20 Making a Radio Call . 21 Making a Talkgroup Call . 21 Repeater or Direct Operation . 21 Monitoring Features . 22 Monitoring a Channel . 22 Conventional Mode Operation . 22 Advanced Features . 23 Advanced Call Features . 23 Receiving and Responding to a Selective Call
(ASTRO Conventional Only) . 23 Using the Dynamic Regrouping Feature
(Trunking Only) . 24 Requesting a Reprogram (Trunking Only) . 24 Classifying Regrouped Radios . 25 Scan Lists . 25 Viewing a Scan List . 25 Viewing and Changing the Priority Status . 25 Scan . 26 Turning Scan On or Off . 26 Making a Dynamic Priority Change
(Conventional Scan Only) . 27 Deleting a Nuisance Channel . 27 Restoring a Nuisance Channel . 27 Call Alert Paging . 28 Receiving a Call Alert Page . 28 s t n e t n o C iv English Emergency Operation . 28 Sending an Emergency Alarm . 29 Sending an Emergency Call (Trunking Only) . 29 Sending an Emergency Alarm with Emergency Call . 30 Sending a Silent Emergency Alarm . 31 Using the Emergency Keep-Alive Feature . 31 Secure Operations . 32 Selecting Secure Transmissions . 32 Selecting Clear Transmissions . 32 Managing Encryption . 33 Loading an Encryption Key . 33 Using the Multikey Feature . 33 Using the Key Zeroization Feature . 34 Requesting an Over-the-Air Rekey
(ASTRO Conventional Only) . 34 Trunking System Controls . 35 Using the Failsoft System . 35 Going Out of Range . 35 Using the Site Trunking Feature . 36 Locking and Unlocking a Site . 36 Viewing and Changing a Site . 36 Viewing the Current Site . 36 Changing the Current Site . 36 Utilities . 37 Using the Flip Display . 37 Selecting a Zone Bank . 37 Selecting the Power Level . 37 Controlling the Display Backlight . 38 Turning Voice Mute On or Off . 38 Using the Time-Out Timer . 38 Using the Conventional Squelch Operation Features . 39 Analog Options . 39 Digital Options . 40 Using the PL Defeat Feature . 40 Using the Digital PTT ID Feature . 41 Using the Smart PTT Feature (Conventional Only) . 41 Helpful Tips . 42 Caring for Your Radio . 42 C o n t e n t s v English Appendix: Maritime Radio Use in the VHF Frequency Range . 49 Special Channel Assignments . 49 Emergency Channel . 49 Non-Commercial Call Channel . 49 Operating Frequency Requirements . 50 Glossary . 52 Commercial Warranty . 56 Cleaning Your Radio . 43 Handling Your Radio . 43 Servicing Your Radio . 44 Taking Care of the Battery . 44 Checking the Battery Charge Status . 44 LED and Sounds . 44 Fuel Gauge Icon . 44 Battery Recycling and Disposal . 45 Accessories . 46 Antennas . 46 Batteries and Battery Accessories . 46 Carry Accessories . 46 Belt Clips . 46 Belt Loops . 46 Carry Cases . 46 Chargers . 47 Audio Accessories . 48 s t n e t n o C vi English Important Safety Information Product Safety and RF Exposure Compliance Before using this product, read the operating instructions for safe usage contained in the Product Safety and RF Exposure booklet enclosed with your radio.
Software Version All the features described in the following sections are supported by the radio's software version R01.00.00 or later. Check with your dealer or system administrator for more details of all the features supported. ATTENTION!
This radio is restricted to occupational use only to satisfy FCC RF energy exposure requirements. Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet enclosed with your radio
(Motorola Publication part number 6881095C98) to ensure compliance with RF energy exposure limits. For a list of Motorola-approved antennas, batteries, and other accessories, visit the following website:
http://www.motorola.com/governmentandenterprise I m p o r t a n t S a f e t y I n f o r m a t i o n vii English Computer Software Copyrights The Motorola products described in this manual may include copyrighted Motorola computer programs stored in semiconductor memories or other media. Laws in the United States and other countries preserve for Motorola certain exclusive rights for copyrighted computer programs, including, but not limited to, the exclusive right to copy or reproduce in any form the copyrighted computer program. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may not be copied, reproduced, modified, reverse-engineered, or distributed in any manner without the express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola, except for the normal non-exclusive license to use that arises by operation of law in the sale of a product. Documentation Copyrights No duplication or distribution of this document or any portion thereof shall take place without the express written permission of Motorola. No part of this manual may be reproduced, distributed, or transmitted in any form or by any means, electronic or mechanical, for any purpose without the express written permission of Motorola. Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola reserves the right to make changes to any products herein to improve readability, function, or design. Motorola does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others. s t h g i r y p o C e r a w t f o S r e t u p m o C viii English Getting Started Take a moment to review the following:
How to Use This Guide . page 1 Notations Used in This Manual . page 1 What Your Dealer/System Administrator Can Tell You. page 2 How to Use This Guide This User Guide covers the basic operation of the APX 7000 Portables. However, your dealer or system administrator may have customized your radio for your specific needs. Check with your dealer or system administrator for more information. Notations Used in This Manual Throughout the text in this publication, you will notice the use of WARNING, Caution, and Note. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed.
An operational procedure, practice, or condition, etc., which may result in injury or death if not carefully observed. An operational procedure, practice, or condition, etc., which may result in damage to the equipment if not carefully observed. G e t t i n g S t a r t e d Note:
An operational procedure, practice, or condition, etc., which is essential to emphasize. 1 English What Your Dealer/System Administrator Can Tell You Check with your dealer or system administrator, if the radio is to be operated in extremely cold temperatures (less than -20C), for the correct radio settings to ensure proper top display operation. You can also consult your dealer or system administrator about the following:
Is your radio preprogrammed with any preset conventional channels?
Which buttons have been preprogrammed to access other features?
What optional accessories may suit your needs?
Preparing Your Radio for Use Assemble your radio by following these steps:
Charging the Battery . page 3 Battery Charger . page 3 Attaching the Battery . page 3 Attaching the Antenna . page 4 Attaching the Belt Clip . page 5 Attaching the Accessory Connector Cover . page 5 Turning On the Radio. page 6 Adjusting the Volume . page 7 i e s U r o f o d a R r u o Y g n i r a p e r P 2 English Charging the Battery Attaching the Battery With the radio turned off, slide the battery into the radios frame until side latches click into place.
To avoid a possible explosion:
DO NOT replace the battery in any area labeled hazardous atmosphere.
DO NOT discard batteries in a fire. The Motorola-approved battery shipped with your radio is uncharged. Prior to using a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and performance. For a list of Motorola-authorized batteries available for use with your radio, see Batteries and Battery Accessories on page 46. Note: When charging a battery attached to a radio, turn the radio off to ensure a full charge. Battery Charger
To charge the battery, place the battery, with or without the radio, in a Motorola-approved charger. The chargers LED indicates the charging progress; see your chargers user guide. For a list of chargers, see Chargers on page 47. P r e p a r i n g Y o u r R a d o f o r U s e i 3 English To remove the battery, turn the radio off. Squeeze the release latches on the bottom of the battery until the battery releases from the radio. Remove the battery from the radio. Note: If your radio is preprogrammed with volatile-key retention, the encryption keys are retained for approximately 30 seconds after battery removal. Check with your dealer or system administrator for more information. Battery Latch Attaching the Antenna With the radio turned off, set the antenna in its receptacle and turn clockwise to attach it to the radio. To remove the antenna, turn the antenna counterclockwise. Make sure you turn off the radio first. i e s U r o f o d a R r u o Y g n i r a p e r P 4 English Attaching the Accessory Connector Cover Attaching the Belt Clip The accessory connector is located on the antenna side of the radio. It is used to connect accessories to the radio. Note:
To prevent damage to the connector, shield it with the connector cover when not in use. Align the grooves of the belt clip with those of the radio and press upward until you hear a click. Insert the hooked end of the cover into the slot above the connector. Press downward on the covers top to seat it in the slot. Once in place, rotate the thumbscrew clockwise by hand until tight. Hooked End Hex Socket Head Thumbscrew To remove the accessory connector cover, rotate the thumbscrew counterclockwise until it disengages from the radio. If the thumbscrew is too tight, use an Allen wrench to loosen it first. Rotate and lift the connector cover to disengage it from the radio. P r e p a r i n g Y o u r R a d o f o r U s e i 5 English To remove the clip, use a flat-bladed object to press the belt clip tab away from the radio. Then, slide the clip downward and away from the radio. Turning On the Radio Rotate the On/Off/Volume Control Knob clockwise until you hear a click. To turn off the radio, rotate the On/Off/Volume Control Knob counterclockwise until you hear a click. If the power-up test is successful, you see SELFTEST on the radios display momentarily, followed by the Home screen. Note:
If the power-up test is unsuccessful, you see ERROR XX/YY (XX/YY is an alphanumeric code). Turn off the radio, check the battery, and turn the radio back on. If the radio fails the power-up test again, record the ERROR XX/YY code and contact your dealer. i e s U r o f o d a R r u o Y g n i r a p e r P 6 English Adjusting the Volume To increase the volume, turn the On/Off/Volume Control Knob clockwise. Identifying Radio Controls Take a moment to review the following:
Radio Parts and Controls . page 8 Programmable Features . page 9 Assignable Radio Functions . page 9 Assignable Settings or Utility Functions . page 10 Accessing the Preprogrammed Functions . page 10 Push-To-Talk (PTT) Button. page 10 Main Speaker To decrease the volume, turn this knob counterclockwise. Note: Ensure that the main speaker is pointed towards you for increased loudness and intelligibility, especially in areas with loud background noises. I i d e n t i f y n g R a d o C o n t r o s i l 7 English Radio Parts and Controls 1 2 Antenna LED 3 Top (Orange) Button*
4 Accessory Connector l i s o r t n o C o d a R g n y f i t n e d i 10 16-Position Select Knob*
5 On/Off/Volume Control Knob 6 3-Position A/B/C Switch*
11 Top Side (Select) Button*
7 2-Position Concentric Switch*
8 Belt Clip 12 Push-to-Talk
(PTT) Button 13 Side Button 1*
14 Side Button 2*
15 Top Display 16 Microphone 17 Main Speaker 18 Battery I 8 English 9 Battery Latch
* These radio controls/buttons are programmable. Programmable Features Any references in this manual to controls that are preprogrammed mean that a qualified radio technician must use the radios programming software to assign a feature to a control. Your dealer can program the programmable buttons as shortcuts to radio functions or preset channels/groups depending on the duration of a button press:
Press Pressing and releasing rapidly.
Long press Pressing and holding for the preprogrammed duration (between 0.25 seconds and 3.75 seconds).
Hold down Keeping the button pressed. Assignable Radio Functions
Call Response Allows you to answer a private call. Channel Selects a channel. Dynamic Priority Allows any channel in a scan list (except for the Priority-One channel) to temporarily replace the Priority-Two channel. Emergency Depending on the programming, initiates or cancels an emergency alarm or call. IP Displays the IP (Internet Protocol) information of the radio. Monitor Monitors a selected channel for all radio traffic until function is disabled. Nuisance Delete Temporarily removes an unwanted channel, except for priority channels or the designated transmit channel, from the scan list. The designated transmit channel refers to the users selected zone/channel combination from which scan is initiated. PL Defeat Overrides any coded squelch (DPL or PL) that is preprogrammed to a channel. Rekey Request Notifies the dispatcher that you want a new encryption keys. Reprogram Request Notifies the dispatcher that you want a new dynamic regrouping assignment. Scan List Programming Selects the scan list for editing. Scan Toggles scan on or off. Secure/Clear Toggles secure operation on or off. Site Display Displays the current site ID and RSSI value. Site Lock/Unlock Locks onto a specific site. Site Search Performs site search for AMSS (Automatic Multiple Site Select) or SmartZone operation. Talkaround/Direct Toggles between using a repeater and communicating directly with another radio. I i d e n t i f y n g R a d o C o n t r o s i l 9 English Zone Select Allows selection from a list of zones. Zone Bank Allows selection from a larger list of zones. Assignable Settings or Utility Functions
Flip Flips the content of the top display. Light Toggles display backlight on or off. TX Power Level Toggles transmit power level between high and low. Voice Mute Toggles voice mute on or off. Volume Set Sets the volume set tone. Accessing the Preprogrammed Functions You can access various radio functions through a short or long press of the relevant programmable buttons. Push-To-Talk (PTT) Button The PTT button on the side of the radio serves two basic purposes:
While a call is in progress, the PTT button allows the radio to transmit to other radios in the call. Press and hold down PTT button to talk. Release the PTT button to listen. The microphone is activated when the PTT button is pressed.
While a call is not in progress, the PTT button is used to make a new call. See Making a Radio Call on page 21 for more information. PTT Button l i s o r t n o C o d a R g n y f i t n e d i I 10 English Identifying Status Indicators Your radio indicates its operational status through the following:
Status Icons. page 11 LED Indicator. page 12 Intelligent Lighting Indicators. page 13 Alert Tones . page 14 Status Icons The 112 x 32 pixel top monochrome display screen of your radio shows the radio status and operating conditions. U Battery The icon shown indicates the charge remaining in the battery. Blinks when the battery is low. V Received Signal Strength Indicator (RSSI) The number of bars displayed represents the received signal strength for the current site, for trunking only. The more stripes in the icon, the stronger the signal. N M Direct
On = Radio is currently configured for direct radio to radio communication (during conventional operation only).
Off = Radio is connected with other radios through a repeater. Monitor (Carrier Squelch) Selected channel is being monitored (during conventional operation only). H orL Power Level
L = Radio is set at Low power.
H = Radio is set at High power. J j Scan Radio is scanning a scan list. Priority-One Channel Scan
Blinking dot = Radio detects activity on channel designated as Priority-
One. I i d e n t i f y n g S t a t u s I i n d c a t o r s
Steady dot = Radio detects activity on channel designated as Priority-Two. 11 English I Vote Scan Enabled The vote scan feature is enabled. View/Program Mode Radio is in the view or program mode.
On steady = View mode
Blinking = Program mode Zone Bank 1
A = Radio is in Zone 1.
B = Radio is in Zone 2.
C = Radio is in Zone 3. Zone Bank 2
D = Radio is in Zone 4.
E = Radio is in Zone 5.
F = Radio is in Zone 6. Secure Operation
On = Secure operation.
Off = Clear operation.
Blinking = Receiving an encrypted voice call. Top Display A orB orC D orE orF G s r o t a c d n i I s u t a t S g n y f i t n e d i I 12 English LED Indicator The LED indicator shows the operational status of your radio. LED Indicator Solid red Radio is transmitting. Blinking red Radio is transmitting at low battery condition. Double blinking red Radio is in Emergency Mode. Rapidly blinking red Radio has failed the self test upon powering up or encountered a fatal error. Solid yellow Channel is busy. Blinking yellow Radio is receiving a secured transmission. Solid green Radio is powering up, or is on a non-priority channel while in the Scan List Programming mode. Blinking green Radio is receiving an individual or telephone call, or is on a Priority-Two channel while in the Scan List Programming mode. Rapidly blinking green Radio is on a Priority-One channel while in the Scan List Programming mode. Intelligent Lighting Indicators This feature temporary changes the backlight of the top display screen to help signal that a radio event has occurred. Note:
This feature must be preprogrammed by a qualified radio technician. Backlight Orange Notification Emergency Alerts Red Critical Alerts Green Call Alerts When The radio initiates an emergency alarm or call. The radio receives an emergency alarm or call. The radio battery is low. The radio is out of range. The radio enters failsoft mode. The radio is unable to establish a full connection with the system. The radio receives a private call. The radio receives a phone call. The radio receives a call alert. The radio receives a selective call. I i d e n t i f y n g S t a t u s I i n d c a t o r s 13 English Alert Tones An alert tone is a sound or group of sounds. Your radio uses alert tones to inform you of your radios conditions. The following table lists these tones and when they occur. You Hear Tone Name Heard Short, Low-Pitched Tone Long, Low-Pitched Tone Radio Self Test Fail Reject Time-Out Timer Warning No ACK Received Individual Call Warning Tone Time-Out Timer Timed Out When radio fails its power-up self test. When unauthorized request is made. Four seconds before time out. When radio fails to receive an acknowledgment. When radio is in an individual call for greater than 6 seconds without any activity. After time out. Talk Prohibit/PTT Inhibit Out of Range Invalid Mode
(When PTT button is pressed) transmissions are not allowed.
(When PTT button is pressed) the radio is out of range of the system. When radio is on an unpreprogrammed channel. A Group of Low-Pitched Tones Busy When the system is busy. s r o t a c d n i I s u t a t S g n y f i t n e d i I 14 English You Hear Medium-Pitched Short, Tone Medium-Pitched Long, Tone Tone Name Valid Key-Press Radio Self Test Pass Clear Voice Priority Channel Received Heard When correct key is pressed. When radio passes its power-up self test. At beginning of a non-coded communication. When activity on a priority channel is received. Emergency Alarm Entry When entering the emergency state. Central Echo Volume Set When central controller has received a request from a radio. When volume is changed on a quiet channel. Emergency Exit When exiting the emergency state. A Group of Medium-Pitched Tones Failsoft Automatic Call Back Talk Permit Keyfail When the trunking system fails. When voice channel is available from previous request.
(When PTT button is pressed) verifying system accepting transmissions. When encryption key has been lost. When status, emergency alarm, or reprogram request ACK is received. Console Acknowledge Received Individual Call When Call Alert or Private Call is received. Call Alert Sent Site Trunking When Call Alert is received by the target radio. When a SmartZone trunking system fails. I i d e n t i f y n g S t a t u s I i n d c a t o r s 15 English You Hear Short, High-Pitched Tone (Chirp) Ringing Low-Pitched Gurgle Unique, Chirp Unique, High-Pitched Chirp Tone Name Heard Low-Battery Chirp When battery is below preset threshold value. Fast Ringing Enhanced Call Sent Phone Call Received Dynamic Regrouping When system is searching for target of Private Call. When waiting for target of Private Call to answer the call. When a land-to-mobile phone call is received.
(When the PTT button is pressed) a dynamic ID has been received. New Message When a new message is received. Priority Status When a priority message is received. s r o t a c d n i I s u t a t S g n y f i t n e d i I 16 English General Radio Operation Once you understand how your APX 7000 Portable is configured, you are ready to use your radio. Use this navigation guide to familiarize yourself with the basic Call features:
Selecting a Zone . page 17 Selecting a Radio Channel . page 18 Receiving and Responding to a Radio Call. page 18 Making a Radio Call . page 21 Repeater or Direct Operation . page 21 Monitoring Features. page 22 Selecting a Zone A zone is a group of channels. 3-Position A/B/C Switch Use the following procedure to select a zone. Note: Your radio must be preprogrammed to allow you to use this feature. Procedure:
1 Move the preprogrammed Zone (3-Position A/B/C) switch to the position of the required zone. G e n e r a l i R a d o O p e r a t i o n 2 Press the PTT button to transmit on the displayed zone channel. 17 English Selecting a Radio Channel Receiving and Responding to a Radio Call A channel is a group of radio characteristics, such as transmit/
receive frequency pairs. Once you have selected the required channel and/or zone, you can proceed to receive and respond to calls. LED Indicator Use the following procedure to select a channel. Note: Your radio must be preprogrammed to allow you to use this feature. If you select a channel that is not within the preprogrammed band, the radio indicates that it is on an unsupported frequency with an audio warning. Procedure:
1 Turn the preprogrammed 16-Position Select knob to the desired channel. The LED lights up solid red while the radio is transmitting, and solid yellow when the radio is receiving a transmission
(conventional mode only). There is no LED indication when the radio receives a transmission in trunking mode. If the radio is receiving a secure transmission, the LED blinks yellow. n o i t a r e p O o d a R i l a r e n e G 2 Press the PTT button to transmit on the displayed zone channel. 18 English Receiving and Responding to a Talkgroup Call
To receive a call from a group of users, your radio must be configured as part of that talkgroup. Procedure:
When you receive a talkgroup call (while on the Home screen), depending on how your radio is preprogrammed:
1 ASTRO Conventional Only:
The LED lights up solid yellow. OR Trunking Only:
The display shows the caller alias or ID. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to respond to the call. The LED lights up solid red. 4 Release the PTT button to listen. See Making a Talkgroup Call on page 21 for details on making a Talkgroup Call.
Receiving and Responding to a Private Call
(Trunking Only) A Private Call is a call from an individual radio to another individual radio. These one-to-one calls between two radios are not heard by others in the current talkgroup. The calling radio automatically verifies that the receiving radio is active on the system and can display the callers ID. Note:
The radio automatically exits the feature, if the time-out timer is enabled, when the radio is left idle and the timer expires. You will hear the Inactive Exit Tone upon feature exit. Procedure:
When you receive a Private Call:
1 You hear two alert tones and the LED blinks green. The backlight of the screen turns green and the display shows CALL RCV, alternating with the caller alias (name) or ID
(number). G e n e r a l i R a d o O p e r a t i o n 19 English 2 Press the Call Response button within 20 seconds after the call indicators begin. 3 Press and hold the PTT button to talk. Release the PTT button to listen. 4 Press the Call Response button to hang up and return to the Home screen. You cannot initiate a Private Call.
Receiving and Responding to a Telephone Call
(Trunking Only) This feature allows you to receive calls similar to standard phone calls from a landline phone. Note:
The radio automatically exits the feature, if the time-out timer is enabled, when the radio is left idle and the timer expires. You will hear the Inactive Exit Tone upon feature exit. Procedure:
When you receive a Telephone Call:
1 You hear a telephone-type ringing and the LED blinks green. The backlight of the screen turns green and the display shows PHN CALL. 2 Press the Call Response button within 20 seconds after the call indicators begin. 3 Press and hold the PTT button to talk. Release the PTT button to listen. 4 Press the Call Response button to hang up and return to the Home screen. You cannot initiate a Telephone Call. n o i t a r e p O o d a R i l a r e n e G 20 English Making a Radio Call Repeater or Direct Operation You can select a zone, channel, or talkgroup by using:
The preprogrammed Zone switch
The Channel Selector Knob Making a Talkgroup Call
To make a call to a group of users, your radio must be configured as part of that talkgroup. Procedure:
1 Turn the Channel Selector Knob to select the channel with the desired talkgroup. 2 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 3 Press the PTT button to make the call. 4 ASTRO Conventional Only:
The LED lights up solid red. The display shows the talkgroup alias or ID. OR Trunking Only:
The LED lights up solid red. 5 Speak clearly into the microphone. 6 Release the PTT button to listen. The REPEATER operation increases the radios range by connecting with other radios through a repeater. The transmit and receive frequencies are different. The DIRECT or talkaround operation allows you to bypass the repeater and connect directly to another radio. The transmit and receive frequencies are the same. Procedure:
1 Press the preprogrammed Repeater/Direct switch to toggle between talkaround and repeater modes. 2 The display shows RPTR MOD if the radio is currently in Repeater mode. OR The display shows DIR MODE and the Talkaround icon if the radio is currently in Direct mode (during conventional operation only). G e n e r a l i R a d o O p e r a t i o n 21 English Conventional Mode Operation
Your radio may be preprogrammed to receive Private-Line
(PL) calls. Procedure:
1 Momentarily press the Monitor button to listen for activity. The Carrier Squelch indicator appears on the display. 2 Press and hold the Monitor button to set continuous monitor operation. The duration of the button press is programmable. 3 Press the Monitor button again, or the PTT button, to return to the original squelch setting. If you try to transmit on a receive-only channel, you hear an invalid tone until you release the PTT button. Monitoring Features Radio users who switch from analog to digital radios often assume that the lack of static on a digital channel is an indication that the radio is not working properly. This is not the case. Digital technology quiets the transmission by removing the noise from the signal and allowing only the clear voice or data information to be heard. Use the Monitor feature to make sure a channel is clear before transmitting. Monitoring a Channel
Procedure:
1 Press the preprogrammed Monitor button. 2 Press and hold the Volume Set button to hear the volume set tone. 3 Adjust the Volume Control knob if necessary. 4 Release the Volume Set button. 5 Press and hold the PTT button to transmit. The LED lights up solid red. 6 Release the PTT button to receive (listen). n o i t a r e p O o d a R i l a r e n e G The Carrier Squelch indicator appears on the display when you monitor a channel via the preprogrammed Monitor button. 22 English Advanced Features Use this navigation guide to learn more about advanced features available with your radio:
Advanced Call Features . page 23 Scan Lists . page 25 Scan . page 26 Call Alert Paging . page 28 Emergency Operation . page 28 Secure Operations. page 32 Trunking System Controls . page 35 Utilities. page 37 Advanced Call Features A d v a n c e d F e a t u r e s
Receiving and Responding to a Selective Call
(ASTRO Conventional Only) This feature allows you to receive a call from or to call a specific individual. It is intended to provide privacy and to eliminate the annoyance of having to listen to conversations that are of no interest to you. Procedure:
1 When you receive a Selective Call, you hear two alert tones and the LED lights up solid yellow. The backlight of the screen momentarily turns green and the display briefly shows CALL RCV. 2 The speaker unmutes. 3 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 4 Press and hold the PTT button to talk. Release the PTT button to listen. You cannot initiate a Selective Call. 23 English Requesting a Reprogram (Trunking Only)
This feature lets you notify the dispatcher that you want a new dynamic regrouping assignment. Procedure:
1 Press the preprogrammed Reprogram Request button to send reprogram request to the dispatcher. 2 The display alternates between RPGM and PLS WAIT. 3 If you hear five beeps, the dispatcher has acknowledged the reprogram request. The display shows ACK RCVD and the radio returns to the Home screen. OR If the dispatcher does not acknowledge the reprogram request within six seconds, a low-pitched alert tone sounds and the display shows NO ACK. The radio returns to the Home screen.
Using the Dynamic Regrouping Feature (Trunking Only) This feature allows the dispatcher to temporarily reassign selected radios to a single special channel so they can communicate with each other. This feature is typically used during special operations and is enabled by a qualified radio technician. You will not notice whether your radio has this feature enabled until a dynamic regrouping command is sent by the dispatcher. Note:
If you try to access a zone or channel that has been reserved by the dispatcher as a dynamically regrouped mode for other users, an invalid tone sounds. Procedure:
1 When your radio is dynamically regrouped, it automatically switches to the dynamically regrouped channel. A gurgle tone sounds and the display shows the dynamically regrouped channels name. 2 Press the PTT button to talk. Release PTT button to listen. When the dispatcher cancels dynamic regrouping, the radio automatically returns to the zone and channel that you were using before the radio was dynamically regrouped. s e r u t a e F d e c n a v d A 24 English Classifying Regrouped Radios
The dispatcher can classify regrouped radios into either of two categories: Select Enabled or Select Disabled.
Select-enabled radios are free to change to any available channel, including the dynamic-regrouping channel, once the user has selected the dynamic-regrouping position.
Select-disabled radios cannot change channels while dynamically regrouped. The dispatcher has forced the radio to remain on the dynamic-regrouping channel. The Scan or Private Call feature cannot be selected while your radio is Select Disabled. Scan Lists Scan lists are created and assigned to individual channels/
groups. Your radio scans for voice activity by cycling through the channel/group sequence specified in the scan list for the current channel/group. Your radio can support up to 125 different scan lists. These lists must be preprogrammed by a qualified radio technician. Viewing a Scan List
Procedure:
Turn the 16-Position Select knob to view the members on the list. A d v a n c e d F e a t u r e s Viewing and Changing the Priority Status
Procedure:
1 Press the Top Side (Select) button to change the priority status of the currently displayed channel or the scan list status icon of the currently displayed channel. 25 English Scan This feature allows you to monitor traffic on different channels by scanning a preprogrammed list of channels. Turning Scan On or Off
Procedure:
1 Press the preprogrammed Scan button, or turn the preprogrammed Scan switch to the Scan on or Scan off position. 2 The display shows SCAN ON and the scan icon, indicating that scan is enabled. OR The display shows SCAN OFF, indicating that scan is disabled. 2 A Scan icon indicates that the current channel is in the scan list as a non-priority channel. The LED lights up solid green. OR A Priority-Two Channel Scan icon indicates that the current channel is in the scan list as the Priority-Two channel. The LED blinks green. OR A Priority-One Channel Scan icon indicates that the current channel is in the scan list as the Priority-One channel. The LED rapidly blinks green. You hear all traffic on the Priority-
One channel, regardless of traffic on non-priority channels. OR No icon indicates that the current channel is deleted from the scan list. s e r u t a e F d e c n a v d A 26 English
Making a Dynamic Priority Change (Conventional Scan Only) While the radio is scanning, the dynamic priority change feature allows you to temporarily assign any channel in a scan list
(except for the Priority-One channel) as the Priority-Two channel. This change remains in effect until scan is turned off. Scan then reverts to the preprogrammed (original) setting. Procedure:
1 When the radio locks onto the channel designated as the new Priority-Two channel, press the preprogrammed Dynamic Priority button. 2 The radio continues scanning the remaining channels in the list. Deleting a Nuisance Channel
If a channel continually generates unwanted calls or noise
(termed a nuisance channel), you can temporarily remove the unwanted channel from the scan list. This capability does not apply to priority channels or the designated transmit channel. Note:
Deleting a nuisance channel is only possible through the preprogrammed Nuisance Channel Delete button. Procedure:
1 When the radio is locked onto the channel to be deleted, press the preprogrammed Nuisance Delete button. 2 The radio continues scanning the remaining channels in the list. Restoring a Nuisance Channel
Procedure:
To restore the deleted nuisance channel, do one of the following:
Turn the radio off and then turning it on again. OR
Stop and restart a scan via the preprogrammed Scan button. OR
Change the channel via the 16-Position Select knob. A d v a n c e d F e a t u r e s 27 English Call Alert Paging Emergency Operation The Emergency feature is used to indicate a critical situation. If the Top (Orange) button is preprogrammed to send an emergency signal, this signal overrides any other communication over the selected channel. Your radio supports the following Emergency modes:
Emergency Alarm
Emergency Call (Trunking Only)
Emergency Alarm with Emergency Call
Silent Emergency Alarm Check with your dealer or system administrator for more information on the programming of this feature. Only one of the Emergency modes above can be assigned to the preprogrammed Emergency button. Note:
To exit emergency at any time, press and hold the preprogrammed Emergency button for about a second. This feature allows your radio to work like a pager. Note:
This feature must be preprogrammed by a qualified radio technician. Receiving a Call Alert Page
Procedure:
1 When you receive a Call Alert page, you hear four repeating alert tones and the LED blinks green. 2 The backlight of the screen turns green and the display briefly shows PAGE RCV. You cannot send a Call Alert page. s e r u t a e F d e c n a v d A 28 English Sending an Emergency Alarm
This feature allows you to send a data transmission, which identifies the radio sending the emergency, to the dispatcher. Procedure:
1 Press the preprogrammed Emergency button. 2 The display shows EMERGNCY and the current zone or channel. A short, medium-pitched tone sounds and the LED rapidly blinks red. OR An invalid tone sounds, if the selected channel does not support emergency. 3 When you receive the dispatchers acknowledgment, the display shows ACK RCVD. Four tones sound, the alarm ends, and the radio exits the Emergency Alarm mode. OR If no acknowledgement is received, the display shows NO ACK. The alarm ends and the radio exits the Emergency Alarm mode. Sending an Emergency Call (Trunking Only)
This feature gives your radio priority access on a channel. Note:
The radio operates in the normal dispatch manner while in Emergency Call, except, if enabled, it returns to one of the following:
Tactical/Non-Revert You talk on the channel you selected before you entered the emergency state.
Non-Tactical/Revert You talk on a preprogrammed emergency channel. The emergency alarm is sent on this same channel. Procedure:
1 Press the preprogrammed Emergency button. 2 The display shows EMERGNCY and the current zone or channel. A short, medium-pitched tone sounds and the LED rapidly blinks red. OR An invalid tone sounds, if the selected channel does not support emergency. A d v a n c e d F e a t u r e s 29 English 3 The radio enters the Emergency Call state when:
You receive the dispatchers acknowledgment. The display shows ACK RCVD. OR You press the PTT button while in the Emergency Alarm mode. 4 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 5 Press and hold the PTT button. Speak clearly into the microphone. 6 Release the PTT button to end the transmission and wait for a response from the dispatcher. 7 Press and hold the preprogrammed Emergency button for about a second to exit the Emergency Call mode. 3 Hold the radio vertically 1 to 2 inches (2.5 to 5.0 cm) from your mouth. 4 Press and hold the PTT button. Speak clearly into the microphone. 5 Release the PTT button to end the transmission and wait for a response from the dispatcher. 6 Press and hold the preprogrammed Emergency button for about a second to exit the Emergency Call mode.
Sending an Emergency Alarm with Emergency Call Procedure:
1 Press the preprogrammed Emergency button. 2 The display shows EMERGNCY and the current zone or channel. A short, medium-pitched tone sounds and the LED rapidly blinks red. OR An invalid tone sounds, if the selected channel does not support emergency. s e r u t a e F d e c n a v d A 30 English Sending a Silent Emergency Alarm
This feature allows you to send an Emergency Alarm to another radio without any audio or visual indicators. Procedure:
1 Press the preprogrammed Emergency button. 2 The display shows no changes, the LED does not light up, and you hear no tones. 3 The silent emergency state continues until you:
Press and hold the preprogrammed Emergency button for about a second to exit the Silent Emergency Alarm mode. OR Press and release the PTT button to exit the Silent Emergency Alarm mode and enter regular dispatch or Emergency Call mode. Note:
For ALL Emergency signals, when changing channels:
If the new channel is also preprogrammed for Emergency, you can change channels while in Emergency operation. The emergency alarm or call continues on the new channel.
If the new channel is NOT preprogrammed for Emergency, the display shows NO EMERG, and you hear an invalid tone until you exit the Emergency state or change to a channel preprogrammed for Emergency. Using the Emergency Keep-Alive Feature
This feature, when enabled, prevents the radio from being turned off via the On/Off Control knob when the radio is in the Emergency state. Note:
The radio only exits the Emergency state using one of the ways mentioned in the previous sections. See Sending an Emergency Alarm on page 29, Sending an Emergency Call (Trunking Only) on page 29, Sending an Emergency Alarm with Emergency Call on page 30, or Sending a Silent Emergency Alarm on page 31. A d v a n c e d F e a t u r e s 31 English Selecting Clear Transmissions
Procedure:
Turn the preprogrammed Secure/Clear switch to the clear position. Note:
If the selected channel is preprogrammed for secure-
only operation when you press the PTT button, an invalid mode tone sounds and the display shows SEC TX. The radio will not transmit until you set the Secure/
Clear switch to the secure position. Advanced Secure Operations Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels. Unlike other forms of security, Motorola digital encryption provides signaling that makes it virtually impossible for others to decode any part of an encrypted message. Selecting Secure Transmissions
Procedure:
Turn the preprogrammed Secure/Clear switch to the secure position. Note:
If the selected channel is preprogrammed for clear-only operation when you press the PTT button, an invalid mode tone sounds and the display shows CLR TX. The radio will not transmit until you set the Secure/
Clear switch to the clear position. s e r u t a e F d e c n a v d A 32 English
Managing Encryption Loading an Encryption Key
Note: Refer to the key-variable loader (KVL) manual for equipment connections and setup. Procedure:
1 Attach the KVL to your radio. 2 The display shows KEYLOAD, and all other radio functions, except for power down, backlight, and volume, are locked out. 3 Select the required keys and press the Menu Select button directly below LOAD on the KVL. This loads the encryption keys into your radio. 4 When the key has been loaded successfully, the radio sounds a short tone for single-key radios. OR When the key has been loaded successfully, the radio sounds an alternating tone for multikey radios. Using the Multikey Feature
This feature allows the radio to be equipped with as many as 48 different encryption keys and supports the DES-OFB algorithm. There are two types:
Conventional Multikey The encryption keys can be tied
(strapped), on a one-per-channel basis, through radio service software. In addition, you can have operator-selectable keys, operator-selectable keysets, and operator-selectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups.
Trunked Multikey If you use your radio for both conventional and trunked applications, you have to strap your encryption keys for trunking on a per-talkgroup or announcement-group basis. In addition, you may strap a different key to other features, such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operator-
selectable key erasure. A d v a n c e d F e a t u r e s 33 English
Requesting an Over-the-Air Rekey (ASTRO Conventional Only) This feature, also known as OTAR, allows the dispatcher to reprogram the encryption keys in the radio remotely. The dispatcher performs the rekey operation upon receiving a rekey request from the user. Procedure:
1 Press and hold the preprogrammed Rekey Request button to send the rekey request. 2 If the rekey operation fails, a bad-key tone sounds and the display shows RKY FAIL. Note:
The rekey operation failure indicates that your radio does not contain the Unique Shadow Key (USK). This key must be loaded into the radio with the key-variable loader (KVL) before the rekey request can be sent. Refer to your local key management supervisor for more information. Using the Key Zeroization Feature
This feature allows you to erase all or selected encryption keys. Procedure:
Use the preprogrammed Top Side (Select) button and Top
(Orange) button to erase the single key in radios with the single-key option, and to erase all keys in radios with the multikey option. 1 Press and hold the Top Side (Select) button. 2 While holding Top Side (Select) button down, press the Top
(Orange) button. 3 The display shows PLS WAIT. 4 When all the encryption keys have been erased, the display shows ALL ERASED. Note: DO NOT press the Top (Orange) button before pressing the Top Side (Select) button, unless you are in an emergency situation as this sends an emergency alarm. s e r u t a e F d e c n a v d A 34 English Trunking System Controls Using the Failsoft System
The failsoft system ensures continuous radio communications during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel. Procedure:
1 During failsoft operation, your radio transmits and receives in conventional operation on a predetermined frequency. 2 A medium-pitched tone sounds every 10 seconds and the display shows FAILSOFT. When the trunking system returns to normal operation, your radio automatically leaves failsoft operation and returns to trunked operation. Going Out of Range
When your radio goes out of the range of the system, it can no longer lock onto a control channel. Procedure:
1 A low-pitched tone sounds. AND/OR The display shows the currently selected zone/channel combination and OUT RNG. 2 Your radio remains in this out-of-range condition until:
It locks onto a control channel. OR It locks onto a failsoft channel. OR It is turned off. A d v a n c e d F e a t u r e s 35 English Using the Site Trunking Feature
If the zone controller loses communication with any site, that site reverts to site trunking. The display shows the currently selected zone/channel combination and STE TRNK. Note: When this occurs, you can communicate only with other radios within your trunking site. Locking and Unlocking a Site
This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature should be used with caution, since it inhibits roaming to another site in a wide-area system. Procedure:
1 Use the preprogrammed Site Lock/Unlock button to toggle the lock state between locked and unlocked. 2 The radio saves the new site lock state and returns to the Home screen. s e r u t a e F d e c n a v d A 36 English Viewing and Changing a Site
This feature allows you to view the number of the current site or force your radio to change to a new one. Viewing the Current Site
Procedure:
1 Press the preprogrammed Site Search button. 2 The display momentarily shows the name of the current site and its corresponding received signal strength indicator
(RSSI). Changing the Current Site
Procedure:
1 Press and hold down the preprogrammed Site Search button. 2 A tone sounds and the display momentarily shows SCANNING. 3 When the radio finds a new site, it returns to the Home screen. Utilities Using the Flip Display
This feature allows you to flip the content of the top display upside down. It is particularly useful when you would like to read the top display while the radio is still in the carry holder attached to your belt. Procedure:
Press and hold the preprogrammed Light button to flip the display. Selecting a Zone Bank
This feature allows twice as many zones to be accessed from a switch, doubling the amount of switch positions. Note:
The Zone Select feature must to be preprogrammed to the 3-position A-B-C switch, while the Zone Bank feature must be preprogrammed to any side button or Top (Orange) button before you can use this feature. Procedure:
1 Use the preprogrammed Zone Bank button to toggle the position between Bank 1 and Bank 2. 2 The top display shows the status icons (A, B, C, D, E or F) or the zone name based on the bank and switch position selected. See Zone Bank 1 and Zone Bank 2 on page 12 for more information on the status icons. Selecting the Power Level
You can select the power level at which your radio transmits. The radio always turns on to the default setting. Note:
This feature must be preprogrammed by a qualified radio technician. A d v a n c e d F e a t u r e s Settings:
Select Low for a shorter transmitting distance and to conserve power.
Select High for a longer transmitting distance. 37 English Turning Voice Mute On or Off
You can enable and disable voice transmission, if needed. Procedure:
1 Press the preprogrammed Voice Mute button to turn the feature off or on. 2 The display momentarily shows VMUT OFF, and a short tone sounds, indicating that the feature is disabled. OR The display momentarily shows VMUT ON, and a short tone sounds, indicating that the feature is enabled. Using the Time-Out Timer
This feature turns off your radios transmitter. You cannot transmit longer than the preset timer setting. If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone. Procedure:
1 Press the preprogrammed Transmit Power Level Switch to toggle the power level between low and high power. 2 The display shows LOW PWR and the low power icon. OR The display shows HIGH PWR and the high power icon. Controlling the Display Backlight
You can enable or disable the radios display backlight as needed, if poor light conditions make the display difficult to read. Procedure:
Press the preprogrammed Light button to toggle the backlight on or off. OR Press any programmable radio controls or buttons to turn the backlight on. Note:
The backlight remains on for a preprogrammed time before it automatically turns off completely or returns to the minimum backlight level. s e r u t a e F d e c n a v d A 38 English The timer is defaulted at 60 seconds, but it can be preprogrammed from 3 to 120 seconds, in 15-second intervals, or it can be disabled entirely for each radio mode, by a qualified radio technician. Note: You will hear a brief, low-pitched, warning tone four seconds before the transmission times out. Procedure:
1 Hold down the PTT button longer than the preprogrammed time. You hear a short, low-pitched warning tone, the transmission is cut-off, and the LED goes out until you release the PTT button. 2 Release the PTT button. The timer resets. 3 Press the PTT button to re-transmit. The time-out timer restarts and the LED lights up solid red.
Using the Conventional Squelch Operation Features This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise. Analog Options
Tone Private Line (PL), Digital Private-Line (DPL), and carrier squelch can be available (preprogrammed) per channel. Mode Carrier squelch (C) PL or DPL Result You hear all traffic on a channel. The radio responds only to your messages. A d v a n c e d F e a t u r e s 39 English Using the PL Defeat Feature
This feature allows you to override any coded squelch (DPL or PL) that might be preprogrammed to a channel. The radio will also unmute to any digital activity on a digital channel. Procedure:
Place the preprogrammed PL Defeat switch in the PL Defeat position. You hear any activity on the channel. OR The radio is muted if no activity is present. Note: When this feature is active, the Carrier Squelch status indicator is displayed. Digital Options
One or more of the following options may be preprogrammed in your radio. Check with your dealer or system administrator for more information. Option Result Digital Carrier-Operated Squelch (COS) Normal Squelch Selective Switch You hear any digital traffic. You hear any digital traffic having the correct network access code. You hear any digital traffic having the correct network access code and correct talkgroup. s e r u t a e F d e c n a v d A 40 English Using the Digital PTT ID Feature
This feature allows you to see the radio ID (number) of the radio from whom you are currently receiving a transmission. This ID, consisting up to a maximum of eight characters, can be viewed by both the receiving radio and the dispatcher. Your radios ID number is also automatically sent every time the PTT button is pressed. This is a per-channel feature. For digital voice transmissions, your radios ID is sent continuously during the voice message. Using the Smart PTT Feature (Conventional Only)
Smart PTT is a per-personality, programmable feature used in conventional radio systems to keep radio users from talking over other radio conversations. When smart PTT is enabled in your radio, you cannot transmit on an active channel. If you try to transmit on an active smart-PTT channel, you hear an alert tone, and the transmission is inhibited. The LED lights up solid yellow to indicate that the channel is busy. Three variations of smart PTT are available:
Transmit Inhibit on Busy Channel with Carrier Transmit Inhibit on Busy Channel with Wrong Squelch Code Quick-Key Override You cannot transmit if any traffic is detected on the channel. You cannot transmit on an active channel with a squelch code or
(if secure-equipped) encryption key other than your own. If the PL code is the same as yours, the transmission is not prevented. This feature can work in conjunction with either of the two above variations. You can override the transmit-inhibit state by quick-keying the radio. In other words, two PTT button presses within the preprogrammed time limit. A d v a n c e d F e a t u r e s 41 English Caring for Your Radio
The APX 7000 radio casting has a vent port that allows for pressure equalization in the radio. Never poke this vent with any objects, such as needles, tweezers, or screwdrivers. This could create leak paths into the radio and the radios submergibility will be lost. Vent Port
(For APX 7000 R Radios Only) The APX 7000 R radio is designed to be submerged to a maximum depth of 6 feet, with a maximum submersion time of 2 hours. Exceeding either maximum limit may result in damage to the radio. Helpful Tips Take a moment to review the following:
Caring for Your Radio . page 42 Cleaning Your Radio . page 43 Handling Your Radio . page 43 Servicing Your Radio . page 44 Taking Care of the Battery. page 44 Checking the Battery Charge Status . page 44 Battery Recycling and Disposal. page 45 s p T i l u f p e H l 42 English
(For APX 7000 R Radios Only) Elastomer technology materials used for seals in rugged portable radios can age with time and environmental exposure. Therefore, Motorola recommends that rugged radios be checked annually as a preventive measure in order to assure the watertight integrity of the radio. Motorola details the disassembly, test, and reassembly procedures along with necessary test equipment needed to inspect, maintain and troubleshoot radio seals in the radios service manual.
If the radio battery contact area has been submerged in water, dry and clean the radio battery contacts before attaching a battery to the radio. Otherwise, the water could short-circuit the radio.
If the radio has been submerged in water, shake the radio well so that any water that may be trapped inside the speaker grille and microphone port can be removed. Otherwise, the water will decrease the audio quality of the radio.
Do not disassemble the radio. This could damage radio seals and result in leak paths into the radio. Any radio maintenance should be performed only by a qualified radio technician. Cleaning Your Radio
To clean the external surfaces of your radio:
1 Combine one teaspoon of mild dishwashing detergent to one gallon of water (0.5% solution). 2 Apply the solution sparingly with a stiff, non-metallic, short-
bristled brush, making sure excess detergent does not get entrapped near the connectors, controls or crevices. Dry the radio thoroughly with a soft, lint-free cloth. 3 Clean battery contacts with a lint-free cloth to remove dirt or grease.
Do not use solvents to clean your radio. Spirits may permanently damage the radio housing. Do not submerge the radio in the detergent solution. l H e p f u l i T p s Handling Your Radio
Do not pound, drop, or throw the radio unnecessarily. Never carry the radio by the antenna.
Avoid subjecting the radio to an excess of liquids. Do not submerge the radio unless it is a ruggedized, APX 7000 R model. 43 English Taking Care of the Battery Checking the Battery Charge Status
Your radio can indicate the batterys charge status through:
the LED and sounds.
the fuel gauge icon on the display. LED and Sounds
When your battery is low:
the LED blinks red when the PTT button is pressed.
you hear a low-battery chirp (short, high-pitched tone).
Fuel Gauge Icon A blinking fuel gauge icon (
) is displayed only when the battery voltage drops to low level. In this case, replace the battery with a fully charged one. 0
Avoid subjecting the radio to corrosives, solvents or spirits.
Do not disassemble the radio.
Keep the accessory-connector cover in place until ready to use the connector. Replace the cover immediately once the accessory has been disconnected. Servicing Your Radio
Proper repair and maintenance procedures will assure efficient operation and long life for this product. A Motorola maintenance agreement will provide expert service to keep this and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola to support maintenance services. Through its maintenance and installation program, Motorola makes available the finest service to those desiring reliable, continuous communications on a contract basis. For a contract service agreement, please contact your nearest Motorola service or sales representative, or an authorized Motorola dealer. Express Service Plus (ESP) is an optional extended service coverage plan, which provides for the repair of this product for an additional period of either one or two years beyond the normal expiration date of the standard warranty. For more information about ESP, contact the Motorola Radio Support Center at 3761 South Central Avenue, Rockford, IL 61102 (800) 227-6772 / (847)725-4200. s p T i l u f p e H l 44 English Battery Recycling and Disposal
In the U.S. and Canada, Motorola participates in the nationwide Rechargeable Battery Recycling Corporation (RBRC) program for NiCd battery collection and recycling. Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, access RBRC's Internet web site at www.rbrc.com or call 1-800-8-
BATTERY. This internet site and telephone number also provide other useful information concerning recycling options for consumers, businesses, and governmental agencies. l H e p f u l i T p s Gauge Battery Charge U T S R Q 76% to 100% full 51% to 75%
26% to 50%
11% to 25%
10% or less (at 10%, the gauge begins blinking) 45 English Accessories Your radio is compatible with the approved accessories listed in this chapter. Contact your dealer for details. Antennas. page 46 Batteries and Battery Accessories . page 46 Carry Accessories. page 46 Belt Clips . page 46 Belt Loops . page 46 Carry Cases. page 46 Chargers . page 47 Audio Accessories. page 48 Antennas s e i r o s s e c c A
800 MHz, GPS Antenna (NAF5085_)
700/800 MHz, VHF GPS Antenna (NAR6591_)
GPS Antenna (NAG4000_) Batteries and Battery Accessories
2000 mAh, IMPRESTM NiMH (FM), IP57 Rugged
(NNTN7035_)
2000 mAh, IMPRESTM NiMH (FM), IP57 (NNTN7036_) 46 English
2100 mAh, IMPRESTM NiMH (Std), IP57 (NNTN7037_)
2500 mAh, IMPRESTM Li-Ion, IP57 (NNTN7038_)
2100 mAh, IMPRESTM NiMH (Std), IP57 Rugged
(NNTN7573_) Carry Accessories Belt Clips
Belt Clip, 3", Plastic (HLN6875_)
Belt Clip Kit, 2.5", Plastic (Compatible with Clamshell Batteries) (NTN8266_) Belt Loops
Swivel Belt Loop, 2.5" (PMLN5407_)
Swivel Belt Loop, 2.75" Replacement Metal (Stainless Steel)
(PMLN5408_)
Swivel Belt Loop, 3" (PMLN5409_) Carry Cases
Nylon Carry Case with 3 Fixed Belt Loop and T-Strap, for Short Radio (PMLN5322_)
Hard Leather Carry Case with 3 Fixed Belt Loop, D-Rings, and T-Strap, for Short Radio (PMLN5323_)
Hard Leather Carry Case (High Activity) with 2.75 Swivel Belt Loop, D-Rings, and T-Strap, for Short Radio
(PMLN5324_)
Nylon Carry Case with 3 Fixed Belt Loop and T-Strap, for Long Radio (PMLN5328_)
Hard Leather Carry Case with 3 Fixed Belt Loop, D-Rings, and T-Strap, for Long Radio (PMLN5329_)
Hard Leather Carry Case (High Activity) with 2.75 Swivel Belt Loop, D-Rings, and T-Strap, for Long Radio
(PMLN5330_)
Carry Strap (NTN5243_) Chargers
IMPRESTM Single-Unit (US Plug) (NNTN7080_)
IMPRESTM Single-Unit (Euro Plug) (NNTN7081_)
IMPRESTM Single-Unit (UK Plug) (NNTN7082_)
IMPRESTM Single-Unit (Aust, NZ Plug) (NNTN7083_)
IMPRESTM Single-Unit (Argentina Plug) (NNTN7084_)
IMPRESTM Single-Unit (US Plug, Euro User Guide)
(NNTN7085_)
IMPRESTM Single-Unit (Korean Plug) (NNTN7261_)
IMPRESTM Multi-Unit, Display (Aust, NZ Plug) (NNTN7063_) A c c e s s o r i e s
IMPRESTM Multi-Unit, Display (US Plug) (NNTN7073_)
IMPRESTM Multi-Unit, Display (UK Plug) (NNTN7074_)
IMPRESTM Multi-Unit, Display (Argentina Plug)
(NNTN7075_)
IMPRESTM Multi-Unit, Display (US Plug, Euro User Guide)
(NNTN7076_)
IMPRESTM Multi-Unit, Display (Korean Plug) (NNTN7077_)
IMPRESTM Multi-Unit, Display (Euro Plug) (NNTN7086_)
IMPRESTM Multi-Unit, Non-Display (US Plug) (NNTN7065_)
IMPRESTM Multi-Unit, Non-Display (Euro Plug)
(NNTN7066_)
IMPRESTM Multi-Unit, Non-Display (UK Plug) (NNTN7067_)
IMPRESTM Multi-Unit, Non-Display (Aust, NZ Plug)
(NNTN7068_)
IMPRESTM Multi-Unit, Non-Display (Argentina Plug)
(NNTN7069_)
IMPRESTM Multi-Unit, Non-Display (US Plug, Euro User Guide) (NNTN7070_)
IMPRESTM Multi-Unit, Non-Display (Korean Plug)
(NNTN7071_) 47 English
1-Wire, Receive Only Earpiece, Beige (RLN5879_)
2-Wire, One Programmable Button, Black (RLN5880_)
2-Wire, One Programmable Button, Beige (RLN5881_)
2-Wire with Translucent Tube, One Programmable Button, Black (RLN5882_)
2-Wire with Translucent Tube, One Programmable Button, Beige (RLN5883_)
3-Wire with Translucent Tube, One Programmable Button, Black (PMLN5111_)
3-Wire with Translucent Tube, One Programmable Button, Beige (PMLN5112_)
Low Noise Kit (RLN5886_)
High Noise Kit (RLN5887_) Audio Accessories
Small Remote Speaker Microphone, IP54, 3.5 mm Jack, Receive Only (PMMN4024_)
Small Remote Speaker Microphone, IP54, 3.5 mm Jack
(PMMN4025_)
Noise Canceling Remote Speaker Microphone, IP54, 3.5 mm Jack (PMMN4062_)
Public Safety Microphone, 18 inch, IP55, 3.5 mm Jack
(PMMN4059_)
Public Safety Microphone, 24 inch, IP55, 3.5 mm Jack
(PMMN4060_)
Public Safety Microphone, 30 inch, IP55, 3.5 mm Jack
(PMMN4061_)
Heavy-Duty Headset (PMLN5275_)
Lightweight Headset (RMN5058_)
Earbud for Remote Speaker Microphone, 3.5 mm Jack, Short Coiled Cable, Receive Only (RLN4885_)
Earpiece with Translucent Tube for Remote Speaker Microphone, 3.5 mm Jack, Short Coiled Cable, Receive Only
(RLN4941_)
Ear Receiver for Remote Speaker Microphone, 3.5 mm Jack, Short Coiled Cable, Receive Only (WADN4190_)
1-Wire, Receive Only Earpiece, Black (RLN5878_) s e i r o s s e c c A 48 English Appendix: Maritime Radio Use in the VHF Frequency Range Take a moment to review the following:
Special Channel Assignments. page 49 Operating Frequency Requirements . page 50 Special Channel Assignments Emergency Channel
If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order:
1 2 MAYDAY, MAYDAY, MAYDAY. THIS IS _____________________, CALL SIGN __________. State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times. Repeat MAYDAY and the name of the vessel. WE ARE LOCATED AT _______________________. 3 4 State the position of the vessel in distress, using any information that will help responders to locate you, e.g.:
latitude and longitude
bearing (state whether you are using true or magnetic north)
distance to a well-known landmark
vessel course, speed or destination State the nature of the distress. Specify what kind of assistance you need. State the number of persons on board and the number needing medical attention, if any. 5 6 7 8 Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc. OVER. 9 10 Wait for a response. 11 If you do not receive an immediate response, remain by the radio and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you. Non-Commercial Call Channel
For non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9. A p p e n d i x
M a r i t i m e R a d o U s e i i n t h e V H F F r e q u e n c y R a n g e 49 English Operating Frequency Requirements Table A-1: VHF Marine Channel List (Continued) e g n a R y c n e u q e r F F H V e h t n i i e s U o d a R e m i t i r a M i
x d n e p p A
A radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows:
on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency on ships subject to the Safety Convention, the radio must be capable of operating:
in the simplex mode on the ship station transmitting frequencies specified in the 156.025 157.425 MHz frequency band, and in the semiduplex mode on the two frequency channels specified in the table below.
Note: Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast Guard. Table A-1: VHF Marine Channel List Frequency (MHz) Transmit 156.050 156.100 Receive 160.650 160.700 Channel Number 1 2 50 English Channel Number
4 5 6 7 8 9 10 11 12 13**
14 15**
16 17**
18 19 20
22 Frequency (MHz) Transmit 156.150 156.200 156.250 156.300 156.350 156.400 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 156.850 156.900 156.950 157.000 157.050 157.100 Receive 160.750 160.800 160.850 160.950 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 156.850 161.500 161.550 161.600 161.650 161.700 Table A-1: VHF Marine Channel List (Continued) Table A-1: VHF Marine Channel List (Continued) Channel Number
24 25 26 27 28 60
62 63
65 66 67**
68 69 71 72 73 74 Frequency (MHz) Transmit 157.150 157.200 157.250 157.300 157.350 157.400 156.025 156.075 156.125 156.175 156.225 156.275 156.325 156.375 156.425 156.475 156.575 156.625 156.675 156.725 Receive 161.750 161.800 161.850 161.900 161.950 162.000 160.625 160.675 160.725 160.775 160.825 160.875 160.925 156.375 156.425 156.475 156.575 156.675 156.725 Channel Number Frequency (MHz) Transmit Receive 75 76 77**
78 79 80
84 85 86 87 88
156.875 156.925 156.975 157.025 157.075 157.125 157.175 157.225 157.275 157.325 157.375 157.425
161.525 161.575 161.625 161.675 161.725 161.775 161.825 161.875 161.925 161.975 162.025
Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.
** Low power (1 W) only
*** Guard band Note: A in the Receive column indicates that the channel is transmit only. A p p e n d i x
M a r i t i m e R a d o U s e i i n t h e V H F F r e q u e n c y R a n g e 51 English
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2009-10-14 | 851 ~ 869 | TNF - Licensed Non-Broadcast Transmitter Held to Face | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2009-10-14
|
||||
1 | Applicant's complete, legal business name |
Motorola Solutions, Inc.
|
||||
1 | FCC Registration Number (FRN) |
0003778479
|
||||
1 | Physical Address |
8000 West Sunrise Blvd
|
||||
1 |
Ft Lauderdale, Florida 33322
|
|||||
1 |
United States
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
T******@TIMCOENGR.COM
|
||||
1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
AZ4
|
||||
1 | Equipment Product Code |
89FT7040
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
D****** Z********
|
||||
1 | Title |
Regulatory Compliance Manager
|
||||
1 | Telephone Number |
95472********
|
||||
1 | Fax Number |
--********
|
||||
1 |
d******@motorolasolutions.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | TNF - Licensed Non-Broadcast Transmitter Held to Face | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | PORTABLE MULTIBAND 2-WAY RADIO | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | Yes | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power listed is rated conducted. Maximum conducted output power is 5.7 Watts in the UHF Band; 2.99 Watts in the 700 MHz Band, and 3.6 Watts in the 800 MHz band per 90.205(s). Minimum output setting is 1W in all cases. This device must be restricted to work related operations in an Occupational/Controlled RF exposure Environment, not exceeding a maximum transmitting duty factor of 50%. All qualified end-users of this device must have the knowledge to control their exposure conditions and/or duration to comply with the Occupational/Controlled SAR limit and requirements. A label, as described in this filing, must be displayed on the device to direct users to specific training information for meeting Occupational Exposure Requirements. Body-worn operating configuration is limited to the specific belt-clip supplied for use with this product that provides at least 2.5 cm separation between the device and the users body. End-users must be informed of the body-worn operating requirements for satisfying RF exposure compliance. The highest reported SAR values are - Head: 4.63 W/kg; Body: 6.74 W/kg accounting for a 50% duty cycle. Note 1: 16K0F3E, 11K0F3E, 8K10F1E, 8K10F1D, 8K10F1W, 20K0F1E. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Motorola
|
||||
1 | Name |
W******** E********
|
||||
1 | Telephone Number |
954-7********
|
||||
1 | Fax Number |
954-7********
|
||||
1 |
F******@motorolasolutions.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 9 | EF | 380 | 470 | 5 | 2 ppm | NOTE 1 | |||||||||||||||||||||||||||||||||
1 | 2 | 9 | EF | 764 | 776 | 2.5 | 1.5 ppm | NOTE 1 | |||||||||||||||||||||||||||||||||
1 | 3 | 9 | EF | 793 | 806 | 2.5 | 1.5 ppm | NOTE 1 | |||||||||||||||||||||||||||||||||
1 | 4 | 9 | EF | 806 | 824 | 3 | 1.5 ppm | NOTE 1 | |||||||||||||||||||||||||||||||||
1 | 5 | 9 | EF | 851 | 869 | 3 | 1.5 ppm | NOTE 1 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC