FCC ID: AZ489FT7162 Portable Two-Way Radio with Bluetooth and WiFi

 

APX Two-Way Radios Model 2 APX N50 User Guide AUGUST 2023 2023 Motorola Solutions, Inc. All rights reserved

*MN009203A01*

MN009203A01-AD MN009203A01-AD Contents Contents List of Figures..............................................................................................................8 List of Tables............................................................................................................... 9 Legal and Support.....................................................................................................10 Intellectual Property and Regulatory Notices...............................................................................10 Legal and Compliance Statements..............................................................................................11 Disclaimer......................................................................................................................... 11 Declaration of Conformity................................................................................................. 11 Industry Canada WLAN Statement...................................................................................12 Important Safety Information.............................................................................................12 Notice to Users (FCC) ......................................................................................................13 FCC Licensing Information............................................................................................... 13 Applying for Canadian License......................................................................................... 14 Maritime Radio Use in the VHF Frequency Range...........................................................14 Emergency Channel...............................................................................................14 Non-Commercial Call Channel...............................................................................15 Operating Frequency Requirements...................................................................... 15 Declaration of Compliance for the Use of Distress and Safety Frequencies......... 17 Technical Parameters for Interfacing External Data Sources................................ 17 Limited Warranty..........................................................................................................................17 MOTOROLA SOLUTIONS COMMUNICATION PRODUCTS.......................................... 17 I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:...................................... 17 II. GENERAL PROVISIONS:............................................................................................ 18 III. STATE LAW RIGHTS:................................................................................................. 18 IV. HOW TO GET WARRANTY SERVICE:...................................................................... 19 V. WHAT THIS WARRANTY DOES NOT COVER:..........................................................19 VI. PATENT AND SOFTWARE PROVISIONS:................................................................ 19 VII. GOVERNING LAW:....................................................................................................20 VIII. For Australia Only......................................................................................................20 Read Me First.............................................................................................................21 Software Version......................................................................................................................... 21 Chapter 1: Radio Care............................................................................................ 22 1.1 Cleaning Your Radio..............................................................................................................22 1.2 Radio Service and Repair......................................................................................................23 1.3 Battery Recycling and Disposal............................................................................................. 23 Chapter 2: Radio Overview.................................................................................... 24 2 MN009203A01-AD Contents 2.1 Keypad Overview...................................................................................................................25 2.2 Programmable Radio Functions............................................................................................ 26 2.3 ViQi........................................................................................................................................ 29 2.3.1 Activating Basic Voice Control................................................................................. 31 2.3.2 Using ViQi Virtual Partner........................................................................................ 31 Chapter 3: Getting Started......................................................................................32 3.1 Attaching and Removing the Battery..................................................................................... 32 Attaching the Battery.........................................................................................................32 Removing the Battery....................................................................................................... 32 3.2 Attaching and Removing the Antenna................................................................................... 32 Attaching the Antenna.......................................................................................................32 Removing the Antenna..................................................................................................... 32 3.3 Attaching and Removing the Accessory Connector Cover....................................................33 Attaching the Accessory Connector Cover....................................................................... 33 Removing the Accessory Connector Cover...................................................................... 33 3.4 Attaching the Belt Clip........................................................................................................... 33 3.5 Charging the Radio................................................................................................................33 3.6 Turning the Radio On or Off.................................................................................................. 34 Turning the Radio On........................................................................................................34 Turning the Radio Off........................................................................................................34 3.7 Adjusting the Volume of the Radio........................................................................................ 34 Chapter 4: Home Screen Overview....................................................................... 35 4.1 Status Indicators.................................................................................................................... 35 4.1.1 Status Icons............................................................................................................. 36 4.1.2 LED Indications........................................................................................................39 4.1.3 Intelligent Lighting Indicators................................................................................... 40 4.1.4 Transmit and Receive Indicators............................................................................. 40 Chapter 5: General Radio Operation..................................................................... 42 5.1 Selecting Zones..................................................................................................................... 42 5.2 Selecting Channels................................................................................................................42 5.2.1 Channel Error Message........................................................................................... 42 5.3 Mode Select Feature............................................................................................................. 42 5.3.1 Saving Zones and Channels....................................................................................43 5.4 Selecting the Power Level..................................................................................................... 43 5.5 Selecting a Radio Profile....................................................................................................... 43 5.6 Enabling and Disabling the Radio Alias.................................................................................43 5.7 Adjusting the Display Backlight..............................................................................................44 5.8 Editing the Time and Date..................................................................................................... 44 5.9 Locking and Unlocking the Controls...................................................................................... 44 3 MN009203A01-AD Contents 5.10 Setting the Tones for Controls and Buttons ........................................................................44 5.11 Setting the Voice Mute.........................................................................................................45 5.12 Using the Time-Out Timer................................................................................................... 45 5.13 Adjusting the Squelch Level................................................................................................ 45 5.14 Conventional Squelch Operation......................................................................................... 46 5.14.1 Setting Conventional Squelch Operation............................................................... 46 5.15 Using the PL Disable Feature..............................................................................................47 5.16 Digital PTT ID Support ........................................................................................................47 5.17 General Radio Information...................................................................................................47 5.17.1 Accessing the General Radio Information............................................................. 47 Chapter 6: Trunking System Controls...................................................................49 6.1 Operating in Failsoft System..................................................................................................49 6.2 Imbalanced Coverage............................................................................................................49 6.3 Out-of-Range Radio...............................................................................................................49 6.4 Site Trunking Feature............................................................................................................ 49 6.5 Site Search............................................................................................................................ 49 6.6 Locking or Unlocking Sites.................................................................................................... 50 6.7 Viewing the Current Site........................................................................................................ 50 6.8 Changing the Current Site..................................................................................................... 50 Chapter 7: Types of Radio Calls............................................................................ 51 7.1 Making Calls.......................................................................................................................... 51 7.2 Receiving Calls...................................................................................................................... 52 7.3 Making Priority Dispatch Calls............................................................................................... 53 Chapter 8: Emergency Operation.......................................................................... 54 8.1 Special Considerations for Emergency Operation.................................................................54 8.2 Sending Emergency Alarms.................................................................................................. 55 8.3 Sending Emergency Alarms with Emergency Calls...............................................................55 8.4 Exiting Emergency Operation................................................................................................ 55 8.5 Remote Emergency............................................................................................................... 56 8.5.1 Sending Remote Emergency to Specific Users....................................................... 56 8.5.2 Manually Refreshing the Remote Emergency List...................................................57 8.5.3 Receiving Remote Emergency................................................................................ 57 8.6 Emergency Keep-Alive.......................................................................................................... 57 8.7 Emergency Beacon............................................................................................................... 57 8.7.1 Sending Emergency Beacons..................................................................................57 8.7.2 Receiving Emergency Beacons............................................................................... 57 8.7.3 Viewing Received Emergency Beacon.................................................................... 58 Chapter 9: Fireground.............................................................................................59 9.1 Entering Fireground Zone Channel (Conventional)............................................................... 59 4 MN009203A01-AD Contents 9.2 Responding to Evacuation Indicator...................................................................................... 59 9.3 Sending Evacuation Tone......................................................................................................60 Chapter 10: Tactical Public Safety (Conventional Only)..................................... 61 10.1 Using TPS Normal Transmission.........................................................................................61 10.2 Using TPS Emergency Transmission.................................................................................. 61 Chapter 11: Man Down (Fall Alert) ........................................................................62 11.1 Radio Alerts When Man Down (Fall Alert) is Triggered....................................................... 62 11.2 Testing Man Down (Fall Alert)............................................................................................. 62 11.3 Exiting Man Down (Fall Alert).............................................................................................. 63 11.4 Reinitiating Man Down (Fall Alert)....................................................................................... 63 Chapter 12: Secure Operations............................................................................. 64 12.1 Switching Between Secure and Clear Transmission........................................................... 64 12.2 Encryption............................................................................................................................64 12.2.1 Multikey Feature.................................................................................................... 64 12.2.2 MDC OTAR (Conventional Only)........................................................................... 65 12.2.3 Infinite UKEK Retention......................................................................................... 65 12.2.4 Hear Clear..............................................................................................................65 12.2.5 Loading Encryption Keys....................................................................................... 66 12.2.6 Selecting Encryption Keys..................................................................................... 66 12.2.7 Selecting Keysets.................................................................................................. 66 12.2.8 Erasing Encryption Keys........................................................................................66 12.2.9 Requesting Over-the-Air Rekey............................................................................. 67 Chapter 13: Scan.....................................................................................................68 13.1 Turning Scan On or Off........................................................................................................68 13.2 Making Dynamic Priority Change (Conventional Scan Only).............................................. 68 13.3 Deleting Nuisance Channel................................................................................................. 68 13.4 Restoring Nuisance Channels............................................................................................. 68 Chapter 14: Scan Lists........................................................................................... 70 14.1 Managing the Scan List....................................................................................................... 70 Chapter 15: Connectivity........................................................................................71 15.1 SmartConnect......................................................................................................................71 15.2 Wi-Fi.................................................................................................................................... 71 15.3 Bluetooth........................................................................................................................... 71 15.3.1 Turning Bluetooth On or Off...................................................................................72 15.3.2 Searching and Pairing the Bluetooth Device......................................................... 72 15.3.3 Turning Bluetooth Audio On or Off.........................................................................72 15.3.4 Viewing and Clearing the Bluetooth Enabled Device Information..........................72 15.4 ASTRO 25 (P25) Programming Over Project 25 (POP25).................................................. 73 5 MN009203A01-AD Contents 15.4.1 Responding to Upgrade Notifications.................................................................... 73 Chapter 16: Location ..............................................................................................74 16.1 Turning Location On or Off.................................................................................................. 74 16.2 Accessing Location..............................................................................................................74 16.3 Selecting Location Formats................................................................................................. 75 16.4 Managing Waypoints........................................................................................................... 75 16.5 Location Feature in Emergency Mode.................................................................................76 16.6 Peer-Location on the Display (ASTRO Conventional).........................................................76 16.7 MGRS Coordinates..............................................................................................................77 Chapter 17: Mission Critical Geofence (ASTRO 25 Trunking)............................ 78 17.1 Entry to the Geofence Area................................................................................................. 78 17.2 Entry to Mission Critical Geofence.......................................................................................79 17.3 Exit from Mission Critical Geofence.....................................................................................79 Chapter 18: Contacts.............................................................................................. 80 18.1 Viewing Contact Details.......................................................................................................80 Chapter 19: Recent Calls........................................................................................81 19.1 Viewing Recent Calls...........................................................................................................81 19.2 Deleting Calls.......................................................................................................................81 Chapter 20: Sending Status................................................................................... 83 Chapter 21: Call Alert Paging.................................................................................84 21.1 Sending Call Alert Page.......................................................................................................84 21.2 Receiving Call Alert Page.................................................................................................... 85 Chapter 22: Automatic Registration Service........................................................ 86 22.1 Selecting ARS Mode............................................................................................................86 Chapter 23: User Login Feature.............................................................................87 23.1 Logging In or Out of the User Login Feature....................................................................... 87 Logging In the User Login Feature................................................................................... 87 Logging Out of the User Login Feature.............................................................................87 Chapter 24: Text Messaging Service.....................................................................89 24.1 TMS Status Icons................................................................................................................ 89 24.2 Accessing Messages........................................................................................................... 90 Chapter 25: Monitor Feature.................................................................................. 91 25.1 Monitoring Channels............................................................................................................91 25.2 Monitoring Conventional Mode............................................................................................ 91 Chapter 26: Remote Monitor.................................................................................. 93 Chapter 27: Transmit Inhibit...................................................................................94 27.1 Enabling or Disabling Transmit Inhibit................................................................................. 94 27.2 Smart PTT (Conventional Only)...........................................................................................94 6 MN009203A01-AD Contents Chapter 28: Dynamic Regrouping (Trunking Only) .............................................96 28.1 Classification of Regrouped Radios.....................................................................................96 28.2 Requesting a Reprogram (Trunking Only)...........................................................................96 Chapter 29: Dynamic Zone Programming............................................................ 97 29.1 Selecting Channels in the Dynamic Zone............................................................................97 29.2 Deleting Channels in the Dynamic Zone............................................................................. 97 Chapter 30: Zone-to-Zone Cloning........................................................................ 98 30.1 Cloning Zones......................................................................................................................98 Chapter 31: Radio Kill ............................................................................................99 31.1 Using Direct Kill to Kill Your Own Radio.............................................................................. 99 Chapter 32: Radio Inhibit......................................................................................100 Chapter 33: Switching between Repeater and Direct Operation...................... 101 Chapter 34: Voice Announcement.......................................................................102 Chapter 35: Site Selectable Alerts.......................................................................103 35.1 Sending Site Selectable Alert Notification......................................................................... 103 35.2 Stopping Site Selectable Alert Notification........................................................................ 103 Chapter 36: Additional Performance Enhancement.......................................... 105 36.1 ASTRO 25 Enhanced Data................................................................................................105 36.2 Dynamic System Resilience.............................................................................................. 105 36.3 Encrypted Integrated Data.................................................................................................105 36.4 SecureNet..........................................................................................................................105 36.5 P25 Digital Vehicular Repeater System.............................................................................105 Chapter 37: Accessories...................................................................................... 106 7 MN009203A01-AD List of Figures List of Figures Figure 1: Radio Overview....................................................................................................................... 24 Figure 2: Keypad Overview.................................................................................................................... 25 Figure 3: Home Screen Display..............................................................................................................35 8 MN009203A01-AD List of Tables List of Tables Table 1: VHF Marine Channel List......................................................................................................... 15 Table 2: Radio Overview Description..................................................................................................... 24 Table 3: Keypad Overview..................................................................................................................... 26 Table 4: Assignable Radio Functions..................................................................................................... 26 Table 5: ViQi Basic Voice Control Commands....................................................................................... 29 Table 6: ViQi Virtual Partner Queries..................................................................................................... 30 Table 7: Home Screen Overview Description.........................................................................................35 Table 8: Status Icons..............................................................................................................................36 Table 9: LED Indications........................................................................................................................ 39 Table 10: Intelligent Lighting Indicators.................................................................................................. 40 Table 11: Transmit and Receive Indicators............................................................................................ 40 Table 12: Emergency Operation Scenarios............................................................................................54 Table 13: TMS Status Icons................................................................................................................... 89 Table 14: TMS Inline Icons.....................................................................................................................89 Table 15: Antenna................................................................................................................................ 106 Table 16: Audio (Push-To-Talk)........................................................................................................... 106 Table 17: Audio (Receive only)............................................................................................................ 107 Table 18: Audio (Wireless)................................................................................................................... 107 Table 19: Battery.................................................................................................................................. 107 Table 20: Cable.................................................................................................................................... 107 Table 21: Carry Solutions..................................................................................................................... 108 Table 22: Charger.................................................................................................................................108 Table 23: Miscellaneous.......................................................................................................................108 9 MN009203A01-AD Legal and Support Legal and Support Intellectual Property and Regulatory Notices Copyrights The Motorola Solutions products described in this document may include copyrighted Motorola Solutions computer programs. Laws in the United States and other countries preserve for Motorola Solutions certain exclusive rights for copyrighted computer programs. Accordingly, any copyrighted Motorola Solutions computer programs contained in the Motorola Solutions products described in this document may not be copied or reproduced in any manner without the express written permission of Motorola Solutions. No part of this document may be reproduced, transmitted, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, without the prior written permission of Motorola Solutions, Inc. Trademarks MOTOROLA, MOTO, MOTOROLA SOLUTIONS, and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. License Rights The purchase of Motorola Solutions products shall not be deemed to grant either directly or by implication, estoppel or otherwise, any license under the copyrights, patents or patent applications of Motorola Solutions, except for the normal non-exclusive, royalty-free license to use that arises by operation of law in the sale of a product. Open Source Content This product may contain Open Source software used under license. Refer to the product installation media for full Open Source Legal Notices and Attribution content. European Union (EU) and United Kingdom (UK) Waste of Electrical and Electronic Equipment (WEEE) Directive The European Union's WEEE directive and the UK's WEEE regulation require that products sold into EU countries and the UK must have the crossed-out wheelie bin label on the product (or the package in some cases). As defined by the WEEE directive, this crossed-out wheelie bin label means that customers and end-users in EU and UK countries should not dispose of electronic and electrical equipment or accessories in household waste. Customers or end-users in EU and UK countries should contact their local equipment supplier representative or service centre for information about the waste collection system in their country. Disclaimer Please note that certain features, facilities, and capabilities described in this document may not be applicable to or licensed for use on a specific system, or may be dependent upon the characteristics of a specific mobile subscriber unit or configuration of certain parameters. Please refer to your Motorola Solutions contact for further information. 10 MN009203A01-AD Legal and Support 2023 Motorola Solutions, Inc. All Rights Reserved Legal and Compliance Statements Disclaimer The information in this document is carefully examined, and is believed to be entirely reliable. However, no responsibility is assumed for inaccuracies. Furthermore, Motorola Solutions reserves the right to change any products to improve readability, function, or design. Motorola Solutions does not assume any liability arising out of the applications or use of any product or circuit described herein; nor does it cover any license under its patent rights, nor the rights of others. Declaration of Conformity Per FCC CFR 47 Part 2 Section 2.1077(a) Responsible Party Name: Motorola Solutions, Inc. Address: 2000 Progress Pkwy, Schaumburg, IL 60196-1078, U.S.A. Phone Number: 1-800-927-2744 Hereby declares that the product:

Model Name: APX N50 conforms to the following regulations:

FCC Part 15, subpart B, section 15.107(a), 15.107(d), and section 15.109(a) Class B Digital Device As a personal computer peripheral, this device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1 This device may not cause harmful interference, and 11 MN009203A01-AD Legal and Support 2 This device must accept any interference received, including interference that may cause undesired operation. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio or TV technician for help. For country code selection usage (WLAN devices) NOTE: The country code selection is for non-US model only and is not available to all US models. Per FCC regulation, all Wi-Fi products marketed in the US must be fixed to US operation channels only. Industry Canada WLAN Statement CAUTION:

1 The device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems. 2 The maximum antenna gain permitted for devices in the bands 52505350 MHz and 5470 5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit. 3 The maximum antenna gain permitted for devices in the band 57525850 MHz shall be such that the equipment still complies with e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate. 4 The worst case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2 (3) shall be clearly indicated. 5 User should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 52505350 MHz and 56505850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Important Safety Information RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios CAUTION:

This radio is restricted to Occupational use only. Before using the radio, read the RF Energy Exposure and Product Safety Guide for Portable Two-Way Radios which contains important operating instructions for safe usage and RF energy awareness and control for Compliance with applicable standards and Regulations. For a list of Motorola Solutions-approved antennas, batteries, and other accessories, visit the following website:

12 MN009203A01-AD Legal and Support https://www.motorolasolutions.com Any modification to this device, not expressly authorized by Motorola Solutions, may void your authority to operate this device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. This radio transmitter is approved by Industry Canada to operate with a Motorola Solutions-approved antenna with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Notice to Users (FCC) This device complies with Part 15 of the FCC rules per the following conditions:

This device may not cause harmful interference. The device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this device, not expressly approved by Motorola Solutions, could void the authority of the user to operate this equipment. FCC Licensing Information This device complies with Parts 90 and 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the condition that this device does not cause harmful interference. The radio operates on radio frequencies that are regulated by the Federal Communications Commission (FCC). To transmit on these frequencies, you are required to have a license issued by the FCC. Application is made available on FCC Form 601 and Schedules D, H, and Remittance Form 159. To obtain these FCC forms, request document 000601 which includes all forms and instructions. If you wish to have the document faxed, mailed, or have questions, use the following contact information. Fax Contact the Fax-On-Demand system at 1-202-418-0177 Mail Call the FCC forms hotline at 1-800-418-FORM or 1-800-418-3676 Contact For questions regarding FCC license, contact 1-888-CALL-FCC, 1-888-225-5322, or http://

www.fcc.gov. Before filling out your application, you must decide which frequency you can operate on. For questions on determining the radio frequency, call Motorola Solutions Product Services at: 1-800-448- 6686. Changes or modifications not expressly approved by Motorola Solutions may void the user authority granted by the FCC to operate this radio and should not be made. To comply with FCC requirements, transmitter adjustments should be made only by or under the supervision of a person certified as technically qualified to perform transmitter maintenance and repairs in the private land mobile and fixed services as certified by an organization representative of the user of those services. Replacement of any transmitter component such as crystal, semiconductor, and others not authorized by the FCC equipment authorization for this radio could violate FCC rules. NOTE: Use of this radio outside the country where it was intended to be distributed is subject to government regulations and may be prohibited. 13 MN009203A01-AD Legal and Support Applying for Canadian License The operation of your Motorola Solutions radio is subject to the Radio communications Act and must comply with rules and regulations of the Federal Government's department of Industry Canada. Industry Canada requires that all operators using Private Land Mobile frequencies obtain a radio license before operating their equipment. Prerequisites: Obtain the latest Canadian License Application form at http://www.ic.gc.ca/ic_wp-

pa.htm. Procedure:

1 Fill in the items as per the instructions. Be sure to print legibly. If you need additional space for any item, use the reverse side of the application. 2 Make a copy of your files. 3 Prepare a cheque or money order payable to the "Receiver General for Canada", for an amount for each radio purchased. The license is renewed on April 1st each year, and issued for a period of 12 months. 4 Mail your completed application along with your cheque or money order to the closest Industry Canada District office. 14 Avis juridique et soutien Dclarations juridiques et de conformit Avis de non-responsabilit Linformation contenue dans le prsent document a t examine avec soin et est considre comme tant entirement fiable. Cependant, nous nassumons aucune responsabilit en cas dinexactitude. De plus, Motorola Solutions se rserve le droit dapporter des modifications tout produit afin den amliorer la lisibilit, la fonctionnalit ou la conception. Motorola Solutions nassume aucune responsabilit quant aux applications ou lutilisation des produits et circuits dcrits dans le prsent document, pas plus quelle ne se porte garante des licences exploites en vertu de ses droits de brevet ou des droits dun tiers. Dclaration de conformit Rglement CFR 47, partie 2, section 2.1077(a) de la FCC Partie responsable Nom : Motorola Solutions, Inc. Adresse : 2000 Progress Pkwy, Schaumburg, IL 60196-1078, tats-Unis Numro de tlphone : 1 800 927-2744 Dclare par les prsentes que le produit :

Nom du modle : APX N50 est conforme aux rglementations suivantes :

Partie 15, sous-partie B, section 15.107(a), 15.107(d) et section 15.109(a) des rglements de la FCC Appareil numrique de classe B En tant que priphrique dordinateur personnel, cet appareil est conforme aux dispositions de la partie 15 des rglements de la FCC. Son utilisation est assujettie aux deux conditions suivantes :

1 Cet appareil ne doit pas causer dinterfrence nuisible; et i Avis juridique et soutien 2 Cet appareil doit accepter toute interfrence reue, y compris les interfrences pouvant entraner un fonctionnement indsirable. REMARQUE :

Cet quipement a fait lobjet de tests et a t dclar conforme aux limites tablies pour un appareil numrique de classe B, conformment la section 15 des rglements de la FCC. Ces limites sont fixes afin doffrir une protection suffisante contre des interfrences nuisibles dans une installation rsidentielle. Cet quipement gnre, utilise et peut mettre de lnergie de radiofrquence et, sil nest pas install ou utilis conformment aux instructions, il peut provoquer un brouillage nuisible aux communications radio. Cependant, il est impossible de garantir quil ny aura aucune interfrence dans une installation particulire. Si cet appareil cause une interfrence nuisible la rception de la radio ou de la tlvision, ce qui peut tre dtermin en teignant et en allumant lappareil, vous tes encourag remdier la situation en prenant une ou plusieurs des mesures suivantes :

Rorienter ou dplacer lantenne rceptrice. Augmenter la distance entre lquipement et le rcepteur. Brancher lappareil dans une autre prise sur un circuit diffrent de celui du rcepteur. Consulter le distributeur ou un technicien de radio ou de tlvision chevronn pour obtenir de laide. Pour un usage en fonction de la slection du code de pays (appareils WLAN) REMARQUE :

La slection du code de pays est pour les modles non .-U. seulement et nest pas disponible sur tous les modles amricains. Conformment la rglementation de la FCC, tous les produits Wi-Fi commercialiss aux tats-Unis doivent tre fixs sur des canaux fonctionnant aux tats-Unis uniquement. Dclaration relative au WLAN (Industrie Canada) MISE EN GARDE :

1 Lappareil fonctionnant dans la bande 5 150 5 250 MHz est uniquement destin une utilisation lintrieur afin de limiter les risques dinterfrences avec les systmes mobiles satellites dans un canal commun. 2 Pour les dispositifs munis dantennes amovibles, le gain dantenne maximal permis pour les dispositifs utilisant les bandes de 5 250 5 350 MHz et de 5 470 5 725 MHz doit tre conforme la limite de puissance isotrope rayonne quivalente (p.i.r.e). 3 Pour les dispositifs munis dantennes amovibles, le gain dantenne maximal permis pour les dispositifs utilisant la bande de 5 752 5 850 MHz doit tre conforme la limite de p.i.r.e spcifie pour lexploitation point point et lexploitation non point point, selon le cas. 4 Les pires angles dinclinaison ncessaires pour rester conforme lexigence de p.i.r.e applicable au masque dlvation, et nonce la section 6.2.2 (3), doivent tre clairement indiqus. 5 Les utilisateurs devraient aussi tre aviss, dune part, que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) des bandes de 5 250 5 350 MHz et de 5650 5 850 MHz et, dautre part, que ces radars pourraient causer du brouillage ou des dommages aux dispositifs de RL-EL. ii Avis juridique et soutien Consignes de scurit importantes Radios bidirectionnelles portatives : exposition aux radiofrquences et scurit du produit MISE EN GARDE :

Cette radio doit tre utilise des fins professionnelles uniquement. Avant dutiliser la radio, lisez le guide Radios bidirectionnelles portatives : exposition aux radiofrquences et scurit du produit, qui contient dimportantes instructions de fonctionnement pour une utilisation scuritaire et des informations sur lexposition aux frquences radiolectriques, dans le but dassurer votre conformit aux normes et rglements en vigueur. Pour obtenir la liste des antennes, des batteries et des autres accessoires approuvs par Motorola Solutions, visitez le site Web suivant :

https://www.motorolasolutions.com Selon la rglementation dIndustrie Canada, cet metteur radio ne peut tre utilis quavec une antenne dont le type et le gain maximal (ou minimal) sont approuvs par Industrie Canada pour cet metteur. Afin de limiter les interfrences radio pour les autres utilisateurs, le type et le gain de lantenne doivent tre choisis de faon ce que la puissance isotrope rayonne quivalente (p.i.r.e) ne soit pas plus forte quil ne le faut pour tablir la communication. Cet metteur radio a t approuv par Industrie Canada pour utilisation avec une antenne approuve par Motorola Solutions offrant le gain maximal autoris et limpdance requise pour le type dantenne indiqu. Il est strictement interdit dutiliser avec cet appareil tout type dantenne ne figurant pas dans cette liste et prsentant un gain suprieur au maximum indiqu pour le type. Avis aux utilisateurs (FCC) Cet appareil est conforme la partie 15 des rglements de la FCC daprs les conditions suivantes :

Cet appareil ne doit pas causer dinterfrence nuisible. Lappareil doit accepter toute interfrence reue, y compris les interfrences pouvant entraner un fonctionnement indsirable. Toute modification apporte cet appareil sans lautorisation explicite de Motorola Solutions peut annuler lautorisation dutiliser cet appareil. Renseignements de licence FCC Cet appareil est conforme aux stipulations des Parties 90 et 15 des rgles de la Federal Communications Commission (FCC). Son utilisation est assujettie la condition quil ne cause pas dinterfrence nuisible. La radio fonctionne sur des frquences radio rgies par la Federal Communications Commission (FCC). Afin de transmettre sur ces frquences, vous devez vous procurer une licence mise par la FCC. La demande doit tre faite en remplissant le formulaire 601 et les annexez D et H, ainsi que le formulaire 159

(Remittance Form) de la FCC. Pour obtenir ces formulaires de la FCC, demandez le document 000601 qui comprend tous les formulaires et les instructions. Si vous souhaitez que le document vous soit envoy par tlcopieur, par la poste, ou si vous avez des questions, utilisez les coordonnes suivantes. Tlcopieur Communiquez avec le systme de tlcopie sur demande au numro 1 202 418-0177 Poste Tlphonez la ligne dassistance de la FCC concernant les formulaires au 1 800 418-FORM ou 1 800 418-3676 iii Avis juridique et soutien Contact Pour des questions concernant la licence de la FCC, adressez-vous au 1 888 CALL-FCC, 1 888 225-5322 ou http://www.fcc.gov. Avant de remplir votre demande, vous devez dcider sur quelle frquence vous souhaitez exploiter les radios. Pour toute question sur le choix de la radiofrquence, appelez les services sur les produits de Motorola Solutions au numro suivant : 1 800 448-6686. Toute modification apporte cet appareil sans lautorisation explicite de Motorola peut annuler lautorisation dutiliser cet appareil, telle quelle est mise par la FCC, et ne devrait pas tre faite. Pour se conformer aux exigences de la FCC, les rglages de lmetteur doivent tre effectus par ou sous la surveillance dun technicien certifie pour faire lentretien et les rparations dmetteur-rcepteur pour les services fixes ou mobiles terrestres privs, dont la certification provient dun reprsentant de lorganisation de lutilisateur de ces services. Le remplacement de nimporte quel composant de lmetteur (comme le quartz, les semi-conducteurs, ou autre) non permis par lautorisation dquipement de la FCC pour cette radio risque denfreindre la rglementation de la FCC. REMARQUE :

Lutilisation de cette radio en dehors du pays pour lequel elle est distribue est soumise aux rglementations gouvernementales et peut tre interdite. Demande de licence canadienne Le fonctionnement de votre radio Motorola Solutions est assujetti la Loi sur la radiocommunication et doit se conformer aux rgles et rglements du ministre Innovation, Sciences et Dveloppement conomique Canada du gouvernement fdral. Industrie Canada exige que les utilisateurs de frquences mobiles terrestres prives obtiennent une licence avant dutiliser leur quipement. Pralables :

Obtenez le plus rcent formulaire de demande de licence canadienne ladresse http://www.ic.gc.ca/

ic_wp-pa.htm. Procdure :

1 Remplissez les lments en suivant les instructions. Assurez-vous dcrire lisiblement. Si vous avez besoin despace supplmentaire pour tout lment, utilisez le verso de la demande. 2 Faites une copie de vos fichiers. 3 Prparez un chque ou un mandat lordre du Receveur gnral du Canada , dun montant correspondant chaque radio achete. La licence est renouvele le 1er avril de chaque anne et est mise pour une priode de 12 mois. 4 Postez votre demande remplie ainsi que votre chque ou votre mandat au bureau de district dInnovation, Sciences et Dveloppement conomique Canada le plus prs. iv MN009203A01-AD Legal and Support Maritime Radio Use in the VHF Frequency Range Special Channel Assignments Emergency Channel If you are in imminent and grave danger at sea and require emergency assistance, use VHF Channel 16 to send a distress call to nearby vessels and the United States Coast Guard. Transmit the following information, in this order:

1 MAYDAY, MAYDAY, MAYDAY. 2 THIS IS _____________________, CALL SIGN __________. State the name of the vessel in distress 3 times, followed by the call sign or other identification of the vessel, stated 3 times. 3 Repeat MAYDAY and the name of the vessel. 4 WE ARE LOCATED AT _______________________. State the position of the vessel in distress, using any information that will help responders to locate you, e.g.:

latitude and longitude bearing (state whether you are using true or magnetic north) distance to a well-known landmark vessel course, speed, or destination 5 State the nature of the distress. 6 Specify what kind of assistance that you need. 7 State the number of persons on board and the number needing medical attention, if any. 8 Mention any other information that would be helpful to responders, such as type of vessel, vessel length and/or tonnage, hull color, etc. 9 OVER. 10 Wait for a response. 14 MN009203A01-AD Legal and Support 11 If you do not receive an immediate response, remain by the radio, and repeat the transmission at intervals until you receive a response. Be prepared to follow any instructions given to you. Non-Commercial Call Channel For non-commercial transmissions, such as fishing reports, rendezvous arrangements, repair scheduling, or berthing information, use VHF Channel 9. Operating Frequency Requirements A radio designated for shipboard use must comply with Federal Communications Commission Rule Part 80 as follows:

on ships subject to Part II of Title III of the Communications Act, the radio must be capable of operating on the 156.800 MHz frequency. on ships subject to the Safety Convention, the radio must be capable of operating:

in the simplex mode on the ship station transmitting frequencies specified in the 156.025 157.425 MHz frequency band, and in the semiduplex mode on the two frequency channels specified in the table below. NOTE:

Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters. Additional information about operating requirements in the Maritime Services can be obtained from the full text of FCC Rule Part 80 and from the US Coast Guard. Table 1: VHF Marine Channel List Channel Number Frequency (MHz) 1 2

4 5 6 7 8 9 10 11 12 13**

14 15**

16 Transmit 156.050 156.100 156.150 156.200 156.250 156.300 156.350 156.400 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 Receive 160.650 160.700 160.750 160.800 160.850 160.950 156.450 156.500 156.550 156.600 156.650 156.700 156.750 156.800 15 MN009203A01-AD Legal and Support 17**

18 19 20

22

24 25 26 27 28 60

62 63

65 66 67**

68 69 71 72 73 74 75 76 77**

78 79 80

84 85 86 16 156.850 156.900 156.950 157.000 157.050 157.100 157.150 157.200 157.250 157.300 157.350 157.400 156.025 156.075 156.125 156.175 156.225 156.275 156.325 156.375 156.425 156.475 156.575 156.625 156.675 156.725

156.875 156.925 156.975 157.025 157.075 157.125 157.175 157.225 157.275 157.325 156.850 161.500 161.550 161.600 161.650 161.700 161.750 161.800 161.850 161.900 161.950 162.000 160.625 160.675 160.725 160.775 160.825 160.875 160.925 156.375 156.425 156.475 156.575 156.675 156.725

161.525 161.575 161.625 161.675 161.725 161.775 161.825 161.875 161.925 MN009203A01-AD Legal and Support 87 88 157.375 157.425 161.975 162.025 NOTE:

* Simplex channels 3, 21, 23, 61, 64, 81, 82, and 83 cannot be lawfully used by the general public in US waters.

** Low power (1 W) only.

*** Guard band. NOTE: A in the Receive column indicates that the channel is transmitted only. Declaration of Compliance for the Use of Distress and Safety Frequencies The radio equipment does not employ a modulation other than the internationally adopted modulation for maritime use when it operates on the distress and safety frequencies specified in RSS-182 Section 7.3. Technical Parameters for Interfacing External Data Sources RS232 18 V 115 Kbps 5000 USB 3.6 V 12 Mbps 90 SB9600 5 V 9.6 Kbps 120 Input Voltage (Volts Peak-to-peak) Max Data Rate Impedance Limited Warranty MOTOROLA SOLUTIONS COMMUNICATION PRODUCTS I. WHAT THIS WARRANTY COVERS AND FOR HOW LONG:

MOTOROLA SOLUTIONS, INC. (MOTOROLA) warrants the MOTOROLA SOLUTIONS manufactured Communication Products listed below (Product) against defects in material and workmanship under normal use and service for a period of time from the date of purchase as scheduled below:

APX N50 Product Accessories One (1) Year One (1) Year MOTOROLA SOLUTIONS, at its option, will at no charge either repair the Product (with new or reconditioned parts), replace it (with a new or reconditioned Product), or refund the purchase price of the Product during the warranty period provided it is returned in accordance with the terms of this warranty. Replaced parts or boards are warranted for the balance of the original applicable warranty period. All replaced parts of Product shall become the property of MOTOROLA SOLUTIONS. This express limited warranty is extended by MOTOROLA SOLUTIONS to the original end user purchaser only and is not assignable or transferable to any other party. This is the complete warranty for the Product manufactured by MOTOROLA SOLUTIONS. MOTOROLA SOLUTIONS assumes no 17 MN009203A01-AD Legal and Support obligations or liability for additions or modifications to this warranty unless made in writing and signed by an officer of MOTOROLA SOLUTIONS. Unless made in a separate agreement between MOTOROLA SOLUTIONS and the original end user purchaser, MOTOROLA SOLUTIONS does not warrant the installation, maintenance or service of the Product. MOTOROLA SOLUTIONS cannot be responsible in any way for any ancillary equipment not furnished by MOTOROLA SOLUTIONS which is attached to or used in connection with the Product, or for operation of the Product with any ancillary equipment, and all such equipment is expressly excluded from this warranty. Because each system which may use the Product is unique, MOTOROLA SOLUTIONS disclaims liability for range, coverage, or operation of the system as a whole under this warranty. MOTOROLA SOLUTIONS offers the following optional extended service contracts. DEVICE MANAGED SERVICES (DMS) ACCIDENTAL DAMAGE Provides for extended hardware repair coverage INCLUDING CHEMICAL, LIQUID, FIRE, AND OTHER PHYSICAL DAMAGE. Accidental damage coverage is available in conjunction with MOTOROLA SOLUTIONSS standard Commercial Warranty and starts from the FIRST DAY the radio is put into use. Service performed under this plan consists of repair or replacement of the covered equipment as set forth in the terms and conditions. Repairs will be made only at the designated MOTOROLA SOLUTIONS repair depot. Local services are not included. MOTOROLA SOLUTIONS will pay the inbound shipping charges only with use of the MOTOROLA SOLUTIONS designated delivery service. MOTOROLA SOLUTIONS will pay for outbound shipping via MOTOROLA SOLUTIONS'S normal shipping methods. DEVICE MANAGED SERVICES (DMS) STANDARD HARDWARE Provides extended hardware normal wear and tear repair coverage beginning AFTER MOTOROLA SOLUTIONSS standard Commercial Warranty period expires. Service performed under this plan consists of repair of the covered equipment as set forth in the terms and conditions. Repairs will be made only at the designated MOTOROLA SOLUTIONS repair depot. Local services are not included. MOTOROLA SOLUTIONS will pay for outbound shipping via MOTOROLA SOLUTIONS'S normal shipping methods. II. GENERAL PROVISIONS:

This warranty sets forth the full extent of MOTOROLA SOLUTIONS'S responsibilities regarding the Product. Repair, replacement, or refund of the purchase price, at MOTOROLA SOLUTIONSs option, is the exclusive remedy. THIS WARRANTY IS GIVEN IN LIEU OF ALL OTHER EXPRESS WARRANTIES. IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. IN NO EVENT SHALL MOTOROLA SOLUTIONS BE LIABLE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT, FOR ANY LOSS OF USE, LOSS OF TIME, INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS OR SAVINGS OR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE SUCH PRODUCT, TO THE FULL EXTENT SUCH MAY BE DISCLAIMED BY LAW. III. STATE LAW RIGHTS:

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY. This warranty gives specific legal rights, and there may be other rights, which may vary from state to state. 18 MN009203A01-AD Legal and Support IV. HOW TO GET WARRANTY SERVICE:

You must provide proof of purchase (bearing the date of purchase and Product item serial number) in order to receive warranty service and, also, deliver or send the Product item, transportation and insurance prepaid, to an authorized warranty service location. Warranty service will be provided by MOTOROLA SOLUTIONS through one of its authorized warranty service locations. If you first contact the company which sold you the Product (e.g., dealer or communication service provider), it can facilitate your obtaining warranty service. You can also call MOTOROLA SOLUTIONS at 1-800-927-2744 US/Canada. V. WHAT THIS WARRANTY DOES NOT COVER:

1 Defects or damage resulting from use of the Product in other than its normal and customary manner. 2 Defects or damage from misuse, accident, water, or neglect. 3 Defects or damage from improper testing, operation, maintenance, installation, alteration, modification, or adjustment. 4 Breakage or damage to antennas unless caused directly by defects in material workmanship. 5 A Product subjected to unauthorized Product modifications, disassembles, or repairs (including, without limitation, the addition to the Product of non-MOTOROLA SOLUTIONS supplied equipment) which adversely affect performance of the Product or interfere with MOTOROLA SOLUTIONS's normal warranty inspection and testing of the Product to verify any warranty claim. 6 Product which has had the serial number removed or made illegible. 7 Rechargeable batteries if:

any of the seals on the battery enclosure of cells are broken or show evidence of tampering. the damage or defect is caused by charging or using the battery in equipment or service other than the Product for which it is specified. 8 Freight costs to the repair depot. 9 A Product which, due to illegal or unauthorized alteration of the software/firmware in the Product, does not function in accordance with MOTOROLA SOLUTIONSs published specifications or the FCC certification labeling in effect for the Product at the time the Product was initially distributed from MOTOROLA SOLUTIONS. 10 Scratches or other cosmetic damage to Product surfaces that does not affect the operation of the Product. 11 Normal and customary wear and tear. VI. PATENT AND SOFTWARE PROVISIONS:

MOTOROLA SOLUTIONS will defend, at its own expense, any suit brought against the end user purchaser to the extent that it is based on a claim that the Product or parts infringe a United States patent, and MOTOROLA SOLUTIONS will pay those costs and damages finally awarded against the end user purchaser in any such suit, which are attributable to any such claim, but such defense and payments are conditioned on the following:

1 that MOTOROLA SOLUTIONS will be notified promptly in writing by such purchaser of any notice of such claim, 2 that MOTOROLA SOLUTIONS will have sole control of the defense of such suit and all negotiations for its settlement or compromise, and 3 should the Product or parts become, or in MOTOROLA SOLUTIONS opinion be likely to become, the subject of a claim of infringement of a United States patent, that such purchaser will permit 19 MN009203A01-AD Legal and Support MOTOROLA SOLUTIONS, at its option and expense, either to procure for such purchaser the right to continue using the Product or parts or to replace or modify the same so that it becomes non-infringing or to grant such purchaser a credit for the Product or parts as depreciated and accept its return. The depreciation will be an equal amount per year over the lifetime of the Product or parts as established by MOTOROLA SOLUTIONS. MOTOROLA SOLUTIONS will have no liability with respect to any claim of patent infringement, which is based upon the combination of the Product or parts furnished hereunder with software, apparatus or devices not furnished by MOTOROLA SOLUTIONS, nor will MOTOROLA SOLUTIONS have any liability for the use of ancillary equipment or software not furnished by MOTOROLA SOLUTIONS, which is attached to or used in connection with the Product. The foregoing states the entire liability of MOTOROLA SOLUTIONS with respect to infringement of patents by the Product or any parts thereof. Laws in the United States and other countries preserve for MOTOROLA SOLUTIONS certain exclusive rights for copyrighted MOTOROLA SOLUTIONS software such as the exclusive rights to reproduce in copies and distribute copies of such MOTOROLA SOLUTIONS software. MOTOROLA SOLUTIONS software may be used in only the Product in which the software was originally embodied and such software in such Product may not be replaced, copied, distributed, modified in any way, or used to produce any derivative thereof. No other use including, without limitation, alteration, modification, reproduction, distribution, or reverse engineering of such MOTOROLA SOLUTIONS software or exercise of rights in such MOTOROLA SOLUTIONS software is permitted. No license is granted by implication, estoppel or otherwise under MOTOROLA SOLUTIONS patent rights or copyrights. VII. GOVERNING LAW:

This Warranty is governed by the laws of the State of Illinois, U.S.A. VIII. For Australia Only This provision applies to products and services supplied by Motorola Solutions to consumers within the meaning of the Australian Consumer Law. This warranty is given by Motorola Solutions Australia Pty Limited (ABN16 004 742 312) of Tally Ho Business Park, 10 Wesley Court. Burwood East, Victoria. Our goods come with guarantees that cannot be excluded under the Australia Consumer Law. For major failures with the service, you are entitled:

To cancel your service contract with us: and To a refund for the unused portion, or to compensation for its reduced value. You are entitled to choose a replacement or refund for a major failure with goods. If a failure with the goods or service does not amount to a major failure, you are entitled to have the failure rectified in a reasonable time. If this is not done, you are entitled to a refund for the goods, and to cancel the contract for the service and obtain a refund of any unused portion. You are also entitled to be compensated for any other reasonably foreseeable loss or damage from a failure in the goods or service. If you have any queries, please call Motorola Solutions Australia at 1800 457 439. You may also visit our website: https://www.motorolasolutions.com/en_xa/support.html for current warranty terms. 20 MN009203A01-AD Read Me First Read Me First This User Guide covers the basic operation of the radio. Notations Used in This Manual Notations such as Warning, Caution, and Notice are used throughout the text in this publication. These notations are used to emphasize that safety hazards exist, and the care that must be taken or observed. WARNING: An operational procedure, practice, or condition, and so on, which can result in injury or death if not carefully observed. CAUTION: An operational procedure, practice, or condition, and so on, which can result in damage to the equipment if not carefully observed. NOTE: An operational procedure, practice, or condition, and so on, which is essential to emphasize. The following special notations identify certain items. Example Description Home button or Phon Buttons and keys are shown in bold print or as an icon. Menu entries are shown similar to the way that they appear on the display of the radio. This means Press the right side of the 4-Way Navigation button. This means that the content with this icon is designated for radio with Volume Control Knob and 16Position Select Knob. What Your Dealer or System Administrator Can Tell You Your dealer or system administrator can customize your radio to your specific needs. If the radio is to be operated in extreme temperatures (less than -30 C or more than +60 C), check with your system administrator for the correct radio settings. You can consult your dealer or system administrator about the following:

Is your radio programmed with any preset conventional channels?

Which buttons have been programmed to access other features?

What optional accessories suit your needs?

NOTE: Specifications vary for different radio models. For more information, contact your system administrator. Software Version All the features described in the following sections are supported by the software version R31.00.00 or later. Contact your system administrator for more details of all the supported features. 21 MN009203A01-AD Chapter 1 : Radio Care Chapter 1 Radio Care Proper radio usage and care ensure efficient operation and long life of the product. CAUTION: Use the radio according to the following recommendations and warnings. Never obstruct or cover the vent port, even with a label. Ensure that no oily substances come in contact with the vent port. Your radio is designed to be submerged to a maximum depth of 6 feet and maximum time of 2 hours. Exceeding either maximum limit may result in damage to the radio. The radio with antenna attached properly is submersible to a maximum depth of 1 meter

(3.28 feet) and a maximum submersion time of 30 minutes. Exceeding either maximum limit or use without antenna may result in damage to the radio. If the radio battery contacts are exposed to water without the battery attached, dry and clean the radio battery contacts before attaching a battery to the radio. Turn the radio over with the battery contact facing down and shake the radio so any trapped water can escape. A short circuit of the contacts could occur if they are not dried properly. If the radio has been submerged in water, shake the radio to remove any water that is trapped inside the speaker grille and microphone port. Otherwise, the water decreases the audio quality of the radio. If an accessory is not attached to the radio, ensure that the accessory connector cover is attached to the radio side accessory connector. If the radio is submerged or exposed to a high force water spray, such as from a hose, remove the accessory or accessory connector cover immediately and ensure that no water is forced into the accessory connector/radio interface. Rinse and dry the area and re-attach the accessory or accessory connector cover if leakage occurs. If the radio is exposed to a corrosive environment, such as salt water or corrosive gases or liquids, rinse and clean the radio immediately to prevent damage to radio materials, especially plated surfaces. Remove the battery and the antenna before cleaning. Do not disassemble the radio as you could damage radio seals and result in leak paths into the radio. Any radio maintenance should be performed only by a qualified radio technician. Only Underwriter Laboratory (UL) approved service centers can open and service UL certified radios. Opening or repairing at unauthorized locations invalidates hazardous location rating of the radio. Do not pound, drop, or throw the radio unnecessarily. Turn off the radio when charging the radio using a wall-mounted charger. Otherwise, the Fall Alert and Emergency may be accidentally triggered. When cleaning the radio, do not use a high-pressure jet spray as this may exceed the depth pressure and cause water to leak into the radio. 1.1 Cleaning Your Radio CAUTION: Do not use solvents to clean your radio as most chemicals may permanently damage the radio housing and textures. Do not submerge the radio in the detergent solution. 22 MN009203A01-AD Chapter 1 : Radio Care To clean the external surfaces of your radio, perform the following:

Procedure:

1 Combine one teaspoon of mild dishwashing detergent to one gallon of water (0.5% solution). 2 Apply the solution sparingly with a stiff, non-metallic, shortbristled brush, making sure that excess detergent does not get entrapped near the connectors, controls, or crevices. 3 Rinse and then dry the radio thoroughly with a soft, lint-free cloth. 4 Clean battery contacts with a lint-free cloth to remove dirt or grease. 1.2 Radio Service and Repair Proper repair and maintenance procedures ensure efficient operation and long-life of this radio. A Motorola Solutions maintenance agreement provides expert service to keep the radio and all other communication equipment in perfect operating condition. A nationwide service organization is provided by Motorola Solutions to support maintenance services. Through its maintenance and installation program, Motorola Solutions makes the finest service available to those desiring reliable continuous communications on a contract basis. For a contract service agreement, contact your nearest Motorola Solutions service or sales representative, or an authorized Motorola Solutions dealer. 1.3 Battery Recycling and Disposal In the U.S. and Canada, Motorola Solutions participates in the nationwide Call2Recycle program for battery collection and recycling. Many retailers and dealers participate in this program. For the location of the drop-off facility closest to you, go to http://www.call2recycle.org/ or call 1-800-8-

BATTERY. This website and telephone number also provide other useful information concerning recycling options for consumers, businesses, and governmental agencies. 23 MN009203A01-AD Chapter 2 : Radio Overview Chapter 2 Radio Overview Figure 1: Radio Overview Table 2: Radio Overview Description Number Name Description Antenna Allows you to transmit and receive electromag-

netic waves during transmitting and receiving. Channel Selector knob Allows you to select channel. On/Off/Volume Control knob Allows you to turn on or off the radio, and adjust the volume. Status LED Provides operating status. 3-Dot Programmable button Programmable button of an assignable radio function. Push-to-Talk (PTT) button Allows you to execute voice operations. 1-Dot Programmable button 2-Dot Programmable button Programmable button of an assignable radio function. Programmable button of an assignable radio function. 1 2 3 4 5 6 7 8 24 54167823141312119101918171615 MN009203A01-AD Chapter 2 : Radio Overview Number Name Description 9 10 11 12 13 14 15 16 17 18 19 Speaker Keypad Display Digital Mic 2 Top Light Bar Top (Orange) button Outputs tones and audio that are generated by the radio. Allows menu navigation and interface selection. The radio display screen. Allows your voice to be sent when PTT or voice operations are activated. Provides indication that a radio event has oc-

curred. Allows you to turn on and off Emergency Op-

erations. Besides the Emergency Operation, this button can also be configured for other fea-

tures. Charging Contacts Charging point for the battery. Battery Provides battery power for your radio. Accessory Connector Belt Clip Bracket Digital Mic 1 Allows you to connect accessories to your ra-

dio. Allows you to attach belt clip. Noise Cancellation Microphone. 2.1 Keypad Overview Figure 2: Keypad Overview 25 243651 MN009203A01-AD Chapter 2 : Radio Overview Table 3: Keypad Overview Number Button Name Description 1 2 3 4 5 6 Menu Select buttons Press to access the corresponding menu. Home button Press to return to Home screen. Programmable button 1 (P1) This button is programmable using the Custom-

er Programming Software (CPS). Programmable button 2 (P2) This button is programmable using the CPS. 4-Way Navigation buttons Press up, down, left, and right to navigate through your options. At the Home screen, press the left or right navigation button to dis-

play the required menu items. Notification button This button is programmable using the CPS. 2.2 Programmable Radio Functions Your system administrator can program the programmable buttons or switches as shortcuts to radio functions depending on the duration of a button press. Contact your system administrator to learn more about the radio functions assigned to the programmable buttons and switches of your radio. Table 4: Assignable Radio Functions Function Audio Playback Description To play the last saved call audio followed by other saved audio in the sequence from oldest to newest. To save the received call audio into your radio, press and hold the button. Basic Voice Control Activates voice commands by pressing and holding. Beacon Allows you to check the details of any recently received Emergency Beacons. Bluetooth On/Off To turn on or off the Bluetooth, press the button. To clear all the Bluetooth devices information, press and hold the button. Bluetooth Configuration Allows you to access the Bluetooth menu. Bluetooth Audio Reroute Allows you to toggle the audio route between the radio speaker or the Remote Speaker Microphone and the Blue-

tooth headset. Bluetooth Headset PTT Enables the Bluetooth Headset microphone. Bluetooth Inquiry On/Off Enables the Bluetooth Search feature. Call Alert Allows the radio to function like a pager, or helps you verify if a radio is active on the system. Call Response Allows you to answer a private call or phone call. Channel Announcement Allows you to hear the Voice Announcement audio file that is assigned to the radio's current channel/mode. 26 MN009203A01-AD Chapter 2 : Radio Overview Function Channel Up/Down Description Allows you to scroll up or down to other channels within the current Zone. Contacts Allows you to access the Contacts menu. Dual Tone Multiple Frequency

(DTMF) Tone Allows you to send out DTMF code of the assigned DTMF value. For example, when DTMF Tone 9 is selected, you can send out DTMF Tone 9. Dynamic Priority (Conventional Only) Allows any channel in a Scan List (except for a Priority-One channel) to temporarily replace the Priority-Two channel. Emergency Info Allows you to send or cancel Emergency Alarm to the dis-

patcher. Allows you to display the Radio Information, Internet Proto-

col (IP) Display, SIM Status, Control Assignments and Soft ID (if enabled). Internet Protocol (IP) Keypad/Control Lock Allows you to display the IP address. Toggles the keypad/control to lock or unlock. Light/Flip Location Man Down Clear To turn on the display backlight on and off, press the button. Displays the current location (latitude, longitude, time, and date), and also the distance and bearing to another location, or toggles GPS/Location between on and off. Allows you to clear and deactivate the Man Down (Fall Alert) Emergency mode alarm. Message Allows you to access the message list. Mode Select (MS01 MS13) Monitor (Conventional Only) Multiple Private Line (Conventional Only) Nuisance Delete Phone Private Call (Trunking Only) To change to the preset Mode Select zone and channel, press the button. When the Preconfigurable Preset Zone and Channel field is enabled, to save the current zone and channel to one of the Mode Select menus, press and hold the preferred Mode Select menu. Monitors a selected channel for all radio traffic until the func-

tion is disabled. Allows you to access the Multiple Private Line lists. Temporarily removes an unwanted channel from scan list, except for priority channels and the designated transmit channel. Allows you to make and receive calls similar to standard phone calls. Allows you to dial the programmed ID (number) and initiate the Private Call. Private Line Disable (Conventional Only) Allows you to adjust squelch level of the radio between level 0 and 15 when you press and hold the button. Priority Channel PTT If in Scan Mode and Priority Member 1 Scan List Member is in the scan list of the current channel, the radio keys up on the Priority 1 Scan List Member channel, therefore allowing 27 MN009203A01-AD Chapter 2 : Radio Overview Function Description Priority Dispatch Radio Profiles Recent Calls Rekey Request Remote Emergency Repeater Access Button (RAB)

(Conventional Only) transmission of voice communication. Otherwise, the radio blocks the transmission and sounds the Talk Prohibit Tone. Allows you to call the dispatcher on a different talkgroup. Allows you to access a set of programmed visual and audio settings of the radio. Allows easy access to the list of calls recently received or made. Notifies the dispatcher that a new encryption key is needed. Activates the Remote Emergency feature for an authorized user to initiate the Emergency feature on a target radio with-

out target user intervention. Allows you to manually send a repeater access codeword. Reprogram Request (Trunking On-

ly) Notifies the dispatcher that a new dynamic regrouping as-

signment is needed. Request-To-Talk (Conventional Only) Notifies the dispatcher that you want to send a voice call. Scan To turn on or off the scan function, press the button. Select Call Sensor To enable Scan List Programming and selects the scan list for editing, press and hold the button. Calls an assigned radio. Allows you to select the time of the Sensor Event Disable Time operation. Site Display/Search (Trunking On-

ly) To display the current site ID and Received Signal Strength Indicator (RSSI) value. To perform site search for Automatic Multiple Site Select

(AMSS) or SmartZone operation, press and hold the button. Site Lock/Unlock (Trunking Only) Allows your radio to lock onto a specific site. Status (Trunking Only) Sends data calls to the dispatcher about a predefined status. Talkaround/Direct (Conventional Only) Toggles between using a repeater or communicating directly with another radio. Talkgroup (Conventional Only) Allows a call from an individual radio to a group of radios. Text Messaging Service (TMS) Third Party TMS Query TMS Quick Text Transmit Power Level Allows you to access the Text Messaging Service (TMS) menu. Allows you to initiate functionality in third-party accessories, such as compatible Whelen Sirens. Launches a list of predefined short text messages only after logging in with Two-Factor Authentication. Selects a predefined message. Toggles between the power levels at which your radio trans-

mits. Unprogrammed Select this feature for a radio button that is not in use. 28 MN009203A01-AD Chapter 2 : Radio Overview Function User Voice Mute Description Allows you to log on to the server with a personally identifia-

ble user name. Allows you to mute the voice transmission of the current zone and channel. Volume Set Tone Sets the volume set tone. 2.3 ViQi ViQi allows you to manage your radio and perform information lookups using voice commands. This feature is purpose-built for easier access to features. You are able to operate the radio with your voice using the following commands. Table 5: ViQi Basic Voice Control Commands Feature Battery Channel Examples To identify your battery level, say the following command:

Battery level To identify your current channel, say the following command:

Channel Home Channel To change to your home channel, say the following command:

Preset Profile Go to home To change the preset of your radio, say Preset <preset number>, The available Preset number is from <1> to <7>. To change the profile of your radio, say the following commands:

Default profile Loud audio profile Surveillance profile Scan To start or stop scanning, say the following commands:

Start scanning Stop scanning Volume To change the volume level of your radio, say one of the availa-

ble commands according to required volume levels:

<volume low> 10%

<volume medium> 50%

<volume high> 100%

Zone To identify your current zone, say the following command:

Zone ViQi Virtual Partner To initiate ViQi Virtual Partner, say the following command:

Hey ViQi 29 MN009203A01-AD Chapter 2 : Radio Overview Feature Examples List of Voice Commands To view the list of voice commands, say the following command:

Go to help ViQi Virtual Partner ViQi Virtual Partner helps you to look up information such as license plate, driver's license, and Vehicle ID Number (VIN), and she responds with a result to your query. Table 6: ViQi Virtual Partner Queries The following table shows the queries supported by the ViQi Virtual Partner feature and their respective commands. Use the following commands followed by the supported query instructions to initiate ViQi Virtual Partner:

Look up... Check... Run a... Query Examples License plate Run a <state> license plate <alphanumeric string>

Check a <state> license plate Look up <state> license plate <alphanumeric string>

Driver's license Run a <state> driver's license <alphanumeric string>

Vehicle Identification Number Check the state of <state> driver's license <alphanumeric string>

Look up <state> driver's license<alphanumeric string>

Check Vehicle Identification Number <alphanumeric string>

VIN check <alphanumeric string>

Run a VIN NOTE: You can use variations such as <Vehicle Identification Number>, <VIN>, and <Vehicle Number>. Own Location Where am I?

Can I get my exact location?

Am I still at the <location> ?

NOTE: ViQi will ask for more information to complete the query. Target Location Where is <unit name> ?

Tell me where <unit name> is NOTE: ViQi will ask for more information to complete the query. 30 MN009203A01-AD Chapter 2 : Radio Overview You are also able to receive and listen to LMR and Virtual Partner over broadband audio simultaneously. These audio mixing is configurable and must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. 2.3.1 Activating Basic Voice Control Prerequisites: Configure a programmable button for basic voice control. Procedure:

1 Press and hold the programmed Basic Voice Control button. 2 Speak your command into the radio mic. 3 Release the programmed Basic Voice Control button. Basic voice control is activated and the radio operates according to the voice command. 2.3.2 Using ViQi Virtual Partner Procedure:

1 Press and hold the programmed ViQi button. 2 After you hear a tone, speak your request into the microphone. 3 Release the assigned programmable button and wait for ViQi to respond. 4 Throughout your session, repeat steps step 1 through step 3 when responding to ViQi. Depending on your query, you can also say the following requests:

To play the available results, say Play results. To request for more details, say More details. To complete the Virtual Partner session, say Complete. 31 MN009203A01-AD Chapter 3 : Getting Started Chapter 3 Getting Started This section provides instructions to prepare your radio for use. 3.1 Attaching and Removing the Battery Attaching the Battery Procedure:

Slide the battery into the radio frame until the latches click into place. Removing the Battery Procedure:

1 Turn off the radio. 2 Lift the latch at the bottom of the radio. 3 Remove the battery from the radio. 3.2 Attaching and Removing the Antenna Attaching the Antenna Prerequisites: Ensure the radio is turned off before attaching the antenna. Procedure:

1 Set the antenna in the receptacle. 2 Turn the antenna clockwise to attach to the radio. Removing the Antenna Prerequisites: Ensure the radio is turned off before removing the antenna. Procedure:

1 Turn the antenna counterclockwise. 2 Remove the antenna from the receptacle. 32 MN009203A01-AD Chapter 3 : Getting Started 3.3 Attaching and Removing the Accessory Connector Cover The accessory connector is on the antenna side of the radio enables you to connect accessories to the radio. NOTE: To prevent damage to the connector, shield it with the connector cover when not in use. Attaching the Accessory Connector Cover Procedure:

1 Insert the hook end of the cover into the slot above the connector. 2 Press the top of the cover downward to place it in the slot. 3 Rotate the thumbscrew clockwise. Removing the Accessory Connector Cover Procedure:

1 Rotate the thumbscrew counterclockwise until it disengages from the radio. NOTE: If the thumbscrew is too tight, use an allen wrench to loosen it. 2 Rotate and lift the connector cover to disengage it from the radio. 3.4 Attaching the Belt Clip Procedure:

Align the grooves of the belt clip with the radio and insert it until you hear a click. 3.5 Charging the Radio Prerequisites:

WARNING:

To avoid possible explosion:

Do not replace the battery in any area labeled Hazardous Atmosphere. Do not discard batteries in a fire. When and where to use: Motorola Solutions-approved battery shipped with your radio is uncharged. Prior to using a new battery, charge it for a minimum of 16 hours to ensure optimum capacity and performance. For a list of Motorola Solutions-authorized batteries and chargers available for use with your radio, see Accessories. NOTE: When charging a battery attached to a radio, the radio must be turned off. Procedure:

1 Turn off the radio while charging in a single or multi-unit charger. 33 MN009203A01-AD Chapter 3 : Getting Started 2 Place the radio in a Motorola Solutions-approved charger. The LED on the charger indicates the charging progress. For more information, see the Charger User Guide. 3.6 Turning the Radio On or Off Prerequisites: Ensure that the battery is fully charged before the first use. Turning the Radio On Procedure:

To turn on, turn the On/Off/Volume Control knob clockwise until you hear a click. Turning the Radio Off Procedure:

To turn off, turn the On/Off/Volume Control knob counterclockwise until you hear a click. 3.7 Adjusting the Volume of the Radio Procedure:

1 To increase the volume, rotate the On/Off/Volume Control knob clockwise. 2 To decrease the volume, rotate the On/Off/Volume Control knob counterclockwise. 34 MN009203A01-AD Home Screen Overview Chapter 4 Home Screen Overview Figure 3: Home Screen Display Table 7: Home Screen Overview Description Number Name Description 1 2 3 4 5 6 Dark Mode Status Bar Bright Mode Status Bar Radio Control Widget Notification Widget Menu Items Time Dark mode status icons appear in the status bar to provide device status and feature notifi-

cations. Bright mode status icons appear in the status bar to provide device status and feature notifi-

cations. Displays the zone, channel, trunking status, and call state. Displays the most recent text message notifica-

tion. Displays the programmed menu items. The available time format is 12 hours (default) and 24 hours. 4.1 Status Indicators This section explains the status indicators of the radio. 35 162345 MN009203A01-AD Chapter 4 : Home Screen Overview 4.1.1 Status Icons These icons appear at the status bar to provide device-specific information or status. Table 8: Status Icons Icon Name Battery Level Description Indicates the remaining battery level of the ra-

dio. The icon blinks when the battery level drops to 10% or lower. Broadband Network is Active Steady The broadband system is available and con-

nected. Blinking The Automatic Registration Service (ARS) user login failed while in Broadband system. Broadband Receiving The radio is receiving the broadband signal. Broadband Transmitting The radio is transmitting the broadband signal. Broadband Receiving and Transmitting The radio is receiving and transmitting the broadband signal. Broadband with ARS User Logged In The ARS user logged on successfully with the broadband system. Broadband Receiving while ARS User Logged In The ARS user logged on successfully with the broadband system. Broadband Transmitting while ARS User Logged In The radio is transmitting a broadband signal with the ARS user logged on. Broadband Receiving and Transmitting while ARS User Logged In Bluetooth On The radio is receiving and transmitting broad-

band signals with the ARS user logged on. The Bluetooth wireless technology is turned on and ready for connection. Bluetooth Connectivity Steady Bluetooth is connected to the external Blue-

tooth device. Blinking The Bluetooth device is disconnected. 36 Icon Name Description Call Received The radio received a call. MN009203A01-AD Chapter 4 : Home Screen Overview Direct Mode The radio is configured for direct radio-to-radio communication in conventional operation. Global Positioning System

(GPS) GPS is enabled and the signal is available. In-Call User Alert The receiving audio turns off. Data Activity Data activity is present on the radio. Regular User Login Indicator (IP Pack-

et Data) Steady The user is associated with the radio. Inverted Monitor Roaming Blinking The device registration or user registration with the server failed due to an invalid user-

name or pin. Inverted The user is logged on to the secured IP packet data. The selected channel is being monitored in con-

ventional operation. The radio has roamed to and is registered to a foreign system. Received Signal Strength Indi-

cator (RSSI) The number of bars represents the received signal strength of the current site in trunking mode. RSSI Out of Range The received signal is too far to be detected. Receiving The radio is receiving a call or data. Transmitting The radio is transmitting a call or data. Satellite Network is Active Steady The satellite system is available and connec-

ted. Blinking The ARS user login failed while in the satel-

lite system. 37 MN009203A01-AD Chapter 4 : Home Screen Overview Icon Name Description Satellite Receiving The radio is receiving a satellite signal. Satellite Transmitting The radio is transmitting a satellite signal. Satellite Receiving and Trans-

mitting The radio is receiving and transmitting satellite signals. Satellite with ARS User Log-

ged In The ARS user logged on successfully with the satellite system. Satellite Receiving while ARS User Logged In The ARS user logged on successfully with the satellite system. Satellite Transmitting while ARS user Logged In The radio is transmitting a satellite signal with the ARS user logged on. Satellite Receiving and Trans-

mitting while ARS User Log-

ged In SmartConnect Capable The radio is receiving and transmitting satellite signals with the ARS user logged on. The current channel is capable of supporting SmartConnect. SmartConnect Connected The current channel is currently connected through the SmartConnect feature. Scan The radio is scanning a scan list. Priority Channel Scan Steady The radio detects activity on the designated Priority-Two channel. Blinking The radio detects activity on the designated Priority-One channel. Vote Scan The Vote Scan feature is enabled. Secure Operation Steady Advanced Encryption Stand-

ard (AES) Secure Operation The radio is operating in a secure channel. Blinking The radio is receiving an encrypted voice call. Steady The radio is operating in an AES-secure channel. 38 Icon Name MN009203A01-AD Chapter 4 : Home Screen Overview Description Blinking The radio is receiving an AES-encrypted voice call. Power Level High The radio is set at high power. Power Level Low The radio is set at low power. Virtual Private Network (VPN) VPN is activated on the radio. Wi-Fi Strength Your radio is connected to a Wi-Fi network. The number of bars represents the signal strength of the Wi-Fi network. Wi-Fi Unavailable Wi-fi network cannot be reached. 4.1.2 LED Indications The LED indications represent the operational status of your radio. A qualified technician can permanently disable the LED indication by preprogramming it. Table 9: LED Indications Indication Solid red Blinking red Status Radio is transmitting. Radio is transmitting at low battery condition or detects an incompatible battery. Double blinking red Radio is transmitting an emergency alarm or call. Rapid blinking red Radio has failed the self-test upon powering up or encountered a fatal error. Solid yellow Radio is receiving in both trunking and conventional clear mode. NOTE: The yellow LED will illuminate only when the busy LED feature is enabled through Customer Programming Software

(CPS). Blinking yellow Radio is receiving a secured transmission. Solid green Radio is powering up. Blinking green Radio is receiving an individual or telephone call. 39 MN009203A01-AD Chapter 4 : Home Screen Overview 4.1.3 Intelligent Lighting Indicators This feature temporarily changes the color of the Top Light Bar and adds a color bar to the main display screen to help signal that a radio event has occurred. Table 10: Intelligent Lighting Indicators Backlight and Bar Color Notification When Orange Emergency Alerts The radio initiates an emergency alarm or call. The radio receives an emergency alarm or call. The radio initiates the Fall Alert (Man Down) Post-Alert timer. Red Critical Alerts The radio battery is low. The radio is out of range. The radio enters Failsoft mode. The radio is unable to establish a full connec-

tion with the system. The radio is unable to authenticate or register with the system. The radio lost the Global Positioning System

(GPS) signal or the GPS function fails. Green Call Alerts The radio receives a private call. The radio receives a phone call. The radio receives a call alert. The radio receives a selective call. The radio enters Geofence. 4.1.4 Transmit and Receive Indicators The Transmit and Receive Indicator indicates the active call state of the radio. Table 11: Transmit and Receive Indicators Indicator Light Bar Color Call State Light Blue Open or Standby Yellow Receiving and Unmuted 40 Indicator Light Bar Color Call State Red Voice Transmission MN009203A01-AD Chapter 4 : Home Screen Overview Light Blue Out of Range Light Blue Smart Connect Gray Unprogrammed Gray Receiving Frequency Error 41 MN009203A01-AD Chapter 5 : General Radio Operation Chapter 5 General Radio Operation This chapter explains the general operations of your radio. 5.1 Selecting Zones A zone is a group of channels. Procedure:

1 Press the Zone menu item. 2 Select the required zone and press Sel. 5.2 Selecting Channels A channel is a group of radio characteristics, such as transmit or receive frequency pairs. Procedure:

Select channels by using the following options. Option Actions Selecting radio channels using the Channel Selector knob Rotate the Channel Selector knob to the required channel. Selecting radio channels from the Menu a Press the Chan menu item. b Select the required channel and press Sel. 5.2.1 Channel Error Message If there is a channel error, your radio displays error messages on the Radio Control Widget. Type Description Unprogrammed The mode is set to an unprogrammed channel. Fail 001 The selected channel is assigned to an incorrect frequency band. 5.3 Mode Select Feature The Mode Select feature allows you to save the current zone and channel on your radio to one of the Mode Select feature menus (MS01MS05) on a programmable side button (MS01MS13). When programmed, pressing the button changes the transmission to the saved zone and channel. When the Preconfigurable Preset Zone and Channel field is enabled, pressing and holding the 42 MN009203A01-AD Chapter 5 : General Radio Operation preferred Mode Select menu saves the current zone and channel to one of the Mode Select menus. The radio displays MS0x is programmed. NOTE: Your radio must be programmed for you to use this feature. 5.3.1 Saving Zones and Channels You can save frequently used zones and channels to the programmable buttons. Prerequisites: Enable the Preconfigurable Preset Zone and Channel field. Procedure:

1 Toggle from your current zone and channel to the required zone and channel. 2 To save zones and channels to a button, press and hold the button you want to program. If the zone and channel is saved, a tone sounds. If the Preconfigurable Preset Zone and Channel field is disabled, a negative tone sounds. NOTE: Short press of the programmed button changes your current transmission to the zone and channel programmed in the button. 5.4 Selecting the Power Level This feature enables you to select the power level at which your radio transmits. Power level Low enables a shorter transmitting distance and power consumption. Power level High enables a longer-

transmitting distance. Prerequisites: This feature must be programmed by a qualified radio technician. Procedure:

Switch to the required power level by pressing the Pwr menu item. The display shows Low power and the Power Level Low icon or the display shows High power and the Power Level High icon. 5.5 Selecting a Radio Profile Procedure:

1 Press the Prfl menu item. 2 Select the required radio profile and press Sel. 5.6 Enabling and Disabling the Radio Alias This feature allows you to display or hide the radio alias (name). 43 MN009203A01-AD Chapter 5 : General Radio Operation Procedure:

Enable or disable the radio alias by pressing the MyID menu item. The display shows momentary Radio ID off, and the radio alias disappears from the Home screen or the display shows momentary Radio ID on, and the radio alias appears on the Home screen. 5.7 Adjusting the Display Backlight You can enable or disable the radio display backlight as needed, if poor light conditions make the display or keypad difficult to read. NOTE: The backlight setting also affects the Menu Select buttons and Navigation button backlighting accordingly. The backlight remains on for a programmed time before it automatically turns off completely or returns to the minimum backlight level. Procedure:

Perform one of the following actions:

To turn the backlight on or off, press the programmed Light/Flip button. To turn the backlight on, press either the Menu Select or Navigation button, or any programmable radio controls or buttons. 5.8 Editing the Time and Date Procedure:

1 Press the Clck menu item. 2 Press Edit. 3 Perform one of the following actions:

To save, select the required time and date. Press Ok. To cancel, press Cncl. To return to the home screen and discard your changes, press the Home button. 5.9 Locking and Unlocking the Controls You can lock your radio keypad, programmable buttons, and knob or knobs to avoid inadvertent entry. Check with your dealer or qualified technician for best selection to suit your usage. Procedure:

1 To lock the controls, press the programmed Keypad/Control Lock button. The display shows Kypd/Ctrl Lock. 2 To unlock the controls, press the button again. 5.10 Setting the Tones for Controls and Buttons If needed, you can enable or disable the tones of navigation buttons and controls. 44 MN009203A01-AD Chapter 5 : General Radio Operation Procedure:

Turn the tones on or off by pressing the Mute menu item. The display shows a notification message indicating if the tones are enabled or disabled. If the tones are enabled, you hear a short tone. 5.11 Setting the Voice Mute This feature allows you to mute the voice transmission of the current zone and channel. Procedure:

Turn Voice Mute on or off by pressing the VMut menu item. If Voice Mute is successfully turned on, your radio shows the following indications:

A short tone sounds. The display shows Voice mute on. If Voice Mute is successfully turned off, your radio shows the following indications:

A short tone sounds. The display shows Voice mute off. 5.12 Using the Time-Out Timer This feature turns off the transmitter of your radio. You cannot transmit longer than the preset timer setting. If you attempt to do so, the radio automatically stops your transmission, and you hear a talk-prohibit tone. NOTE: The default timer is 60 seconds. Contact your system administrator to adjust the timer duration. Procedure:

1 Press and hold the PTT button longer than the programmed time. The radio shows the following indications:

A tone sounds. The transmission is cut off. The LED extinguishes. 2 To reset the timer, release the PTT button. 3 To retransmit, press the PTT button. The time-out timer restarts, and the red LED illuminates. 5.13 Adjusting the Squelch Level The Adjustable Fine Tune Squelch feature allows you to adjust the desired squelch level of the radio between level 0 and 15. 45 MN009203A01-AD Chapter 5 : General Radio Operation The following settings determine the types of call that you receive:

0 Squelch is open and all calls regardless of signal strength and background noise pass through. Lower setting Calls with low signal strength and higher than normal background noise pass through. Higher Setting Calls with low signal strength and higher than normal background noise are filtered out. Procedure:

1 From the Home screen, press and hold the preprogrammed Private Line Disable button. The radio displays the Squelch menu. 2 To adjust the squelch level, perform one of the following actions:

Press - or +. Press the Left or Right navigation button. 3 To return to the Home screen, press the Home button. 5.14 Conventional Squelch Operation This feature filters out unwanted calls with low signal strength or channels that have a higher than normal background noise. Analog Options Tone Private Line, Digital Private-Line, and carrier squelch is available and programmed per channel. Option Carrier squelch Result You hear all traffic on a channel. Tone Private Line or Digital Private-Line The radio responds only to your messages. Digital Options One or more of the following options can be programmed in your radio. For more information, contact your system administrator. Option Result Digital Carrier-Operated Squelch You hear all digital traffic. Normal Squelch Selective Switch You hear any digital traffic having the correct network access code. You hear any digital traffic having the correct network access code and correct talkgroup. 5.14.1 Setting Conventional Squelch Operation Procedure:

1 Press the Sql menu item. 46 MN009203A01-AD Chapter 5 : General Radio Operation 2 Perform one of the following actions:

To increase the squelch volume, press +. To decrease the squelch volume, press -. 3 To return to the selected channel, press the Home button. 5.15 Using the PL Disable Feature This feature allows you to override any coded squelch that preprogrammed to a channel. The radio also unmutes to any digital activity on a digital channel. When this feature is active, the Carrier Squelch status indicator is displayed. Procedure:

Turn on the PL Disable feature by pressing the programmed PL Disable button. One of the following results occurs:

The radio plays the active transmission on the channel. If no activity is present, the radio is muted 5.16 Digital PTT ID Support This feature allows you to see the radio ID (number) of the radio from whom you are currently receiving a transmission. The receiving radio and the dispatcher can view the ID, which consists of up to a maximum of eight characters. The ID number of your radio is also automatically sent every time you press the PTT button. This feature is preprogrammed per channel. For digital voice transmissions, the ID of your radio is sent continuously during the voice message. 5.17 General Radio Information This menu item allows you to view general information of your radio. The available information are:

Radio Information IP Information Control Map Certificates IoT Status Voice Commands 5.17.1 Accessing the General Radio Information Procedure:

1 Press the Info menu item. 2 Perform one of the following actions:

47 MN009203A01-AD Chapter 5 : General Radio Operation To view radio information, press Radio Info. To view IP information, press IP Info. To view Control Map, press Control Map. To view Certificates, press Certificates. To view IoT status, press IoT Status. To view programmed voice commands, press Voice Commands. 48 MN009203A01-AD Trunking System Controls Chapter 6 Trunking System Controls This chapter explains the trunking system control features on your radio. 6.1 Operating in Failsoft System The failsoft system ensures continuous radio communication during a trunked system failure. If a trunking system fails completely, the radio goes into failsoft operation and automatically switches to its failsoft channel. To continue in Failsoft and to communicate with other talkgroups, refer to the following procedure. Procedure:

1 Rotate the Channel Selector knob to change to a different repeater frequency. 2 To call, press and hold the PTT button. 3 To listen, release the PTT button. 6.2 Imbalanced Coverage Imbalanced coverage occurs when the radio is able to receive the control channel but is unable to transmit back to the system. The radio generates a periodic tone and displays No Comms. 6.3 Out-of-Range Radio When your radio goes out of the range of the system, it can no longer lock onto a control channel. You hear a low-pitched tone and/or the display shows the currently selected zone/channel combination and Out of range notification. Your radio remains in this out-of-range condition until it locks onto a control channel or failsoft channel, or if it is turned off. 6.4 Site Trunking Feature If the Zone Controller loses communication with any site, that site reverts to site trunking. When this occurs, you can communicate only with the radios within your trunking site. The display shows the currently selected zone/channel and the Site Trunking message. 6.5 Site Search When searching for a site, your radio is inoperable. In the site search mode, your radio scans for trunked control channels but has yet to connect to the trunking system or reach other trunking states. Other trunking states are such as Out of Range and Imbalanced Coverage. The Searching site indicator alerts you that your radio is attempting to search for a valid trunked control channel. 49 MN009203A01-AD Chapter 6 : Trunking System Controls 6.6 Locking or Unlocking Sites This feature allows your radio to lock onto a specific site and not roam among wide-area talkgroup sites. This feature must be used with caution because it inhibits roaming to another site in a wide-area system. Procedure:

1 Press the Site menu item. 2 Perform one of the following actions:

To lock the site, press Lock. To unlock the site, press Unlk. The display shows a notification to indicate if the site is locked or unlocked. The radio saves the new site lock state and returns to the Home screen. 6.7 Viewing the Current Site Procedure:

Press the programmed Site Displ/Srch button. The display shows the name of the current site and corresponding received RSSI. 6.8 Changing the Current Site Procedure:

Press and hold the programmed Site Displ/Srch button. The radio shows the following indications:

A tone sounds. The display shows momentary Scanning site. When the radio finds a new site, it returns to the Home screen. 50 MN009203A01-AD Types of Radio Calls Chapter 7 Types of Radio Calls Your radio can make a Talkgroup, Private, Selective, and Telephone call in conventional and/or trunking mode. Conventional Mode Trunking Mode SmartConnect Call Type Talkgroup Call This feature is a point-to-multipoint call operation. Your radio must be config-

ured as a member of the talkgroup for you to communicate within the talk-

group. Private Call This feature is a call from one individu-

al radio to another. Selective Call This feature is a call from an individual radio to another individual radio with privacy. Telephone Call This feature allows you to receive calls similar to standard phone calls from a landline phone. 7.1 Making Calls Procedure:

1 Make calls by using the following options. Option Talkgroup Call Actions a To transmit, press and hold the PTT button. b Wait for the Talk Permit Tone. Then, speak into the mi-

crophone. c To listen, release the PTT button. NOTE: You cannot transmit longer than the preset Time-Out Timer setting. If you attempt to do so, the radio automatically stops your transmission, and you hear a tone. Private Call a Enter the Contacts page by pressing the Cnts menu item. 51 MN009203A01-AD Chapter 7 : Types of Radio Calls Option Actions b Select the required preprogrammed contact. c Start the call by pressing the PTT button. d To end the call, press Exit. Selective Call a Enter the Contacts page by pressing the Cnts menu item. b Select the required preprogrammed contact. c Start the call by pressing the PTT button. d To end the call, release the PTT button. Telephone Call a Press the Phon menu item. The display shows the last transmitted or received ID. b To select the required ID, perform one of the following actions:

Press Cnts. To go to the last dialed number, press LNum. c To dial the phone number, press the PTT button. d To talk, press and hold the PTT button and speak into the microphone. e To listen, release the PTT button. 7.2 Receiving Calls Procedure:

Receive calls by using the following options. Option Talkgroup Call Private Call 52 Actions No action is required. Your radio automatically plays the transmission from the talkgroup call. When you receive private calls, your radio shows the follow-

ing indications:

A tone sounds. The green LED blinks. This display shows Call received, and the Call Re-

ceived icon blinks. a Respond by performing one of the following actions:

To reject the call, press Exit. To accept the call, press Resp. b To talk, press and hold the PTT button. c To listen, release the PTT button. d To end the call, press End. MN009203A01-AD Chapter 7 : Types of Radio Calls Option Selective Call Actions For incoming Selective Calls, your radio automatically plays the transmission from the call. a Respond to the call by pressing and holding the PTT button. b Speak into the microphone. Telephone Call Perform one of the following actions:

To receive call, press Call Response. To talk, press and hold the PTT button. To listen, release the PTT button. 7.3 Making Priority Dispatch Calls The Priority Dispatch feature allows you to call the dispatcher on a different talkgroup when a talkgroup is congested. This talkgroup is called the Priority Talkgroup. Each trunking talkgroup can have an assigned Priority Talkgroup. Priority Dispatch is not available in Emergency operations. The Scan feature is suspended when Priority Dispatch is initiated. Prerequisites: The dispatch console that supports this feature must be programmed to use this feature. For more information, contact your system administrator. Procedure:

1 Press the programmed Priority Dispatch button. A tone sounds, and the radio enters Priority Dispatch mode. The radio exits this mode when the Priority Dispatch Time Out Timer expires. 2 Before the Priority Dispatch Time Out Timer expires, press and hold the PTT button to transmit. The display shows the Priority Talkgroup alias. 3 To listen, release the PTT button. The radio exits Priority Dispatch mode, return to its original talkgroup, and displays the home channel alias. 53 MN009203A01-AD Chapter 8 : Emergency Operation Chapter 8 Emergency Operation The Emergency feature is used to indicate a critical situation. An emergency signal overrides any other communication over the selected channel. Your radio supports the following Emergency modes:

Emergency Alarm Emergency Call Emergency Alarm with Emergency Call Only one Emergency mode can be assigned to the Top (Orange) button. Your radio is also programmed to operate in one of the following conditions:

Tactical/Non-Revert The radio sends an emergency alarm and/or makes an emergency call on the current channel. Non-Tactical/Revert for Conventional System The radio reverts to the programmed emergency channel to send an alarm and/or make an emergency call. Non-Tactical/Revert for Trunking System The radio reverts to the programmed emergency talkgroup (trunking system) or channel

(conventional system) to send an alarm and/or make an emergency call. Fall Alert (Man Down) is an alternate way to activate the Emergency feature. For more information, contact your system administrator. 8.1 Special Considerations for Emergency Operation The following scenarios apply during Emergency operation:

Table 12: Emergency Operation Scenarios Scenario Outcome If you press the Top (Orange) button while in a channel that has no Emergency capability. If you change to a channel/mode with no Emer-

gency capability while in Emergency operation. A low-pitched tone sounds. A continuous low-pitched tone sounds until you select a valid Emergency channel/mode or until you disable the Emergency operation. If you change to a channel/mode with Emergen-

cy capability while in Emergency operation. The Emergency Alarm and/or Emergency Call continues on the new channel/mode. If the radio is out-of-range of the system or the emergency alarm is not acknowledged. A tone sounds and the display shows No ac-

knowledge. 54 MN009203A01-AD Chapter 8 : Emergency Operation 8.2 Sending Emergency Alarms Procedure:

Press the programmed Top (Orange) button. Your radio shows the following indications:

A positive indicator tone sounds. The red LED blinks. The display shows Emergency, and the current zone or channel. When you receive acknowledgement from the dispatcher, your radio shows the following indications:

Four tone sounds. The alarm stops. The display shows Ack received. Your radio exits Emergency Alarm mode. 8.3 Sending Emergency Alarms with Emergency Calls Procedure:

1 Press the programmed Top (Orange) button. If successful, your radio shows the following indications:

A positive indicator tone sounds. The red LED blinks momentarily. The display shows Emergency, and the current zone or channel. When the radio exits Emergency Alarm and enters the Emergency Call state, your radio shows one of the following indications:

You receive the dispatcher acknowledgment. The display shows Ack received. You receive no acknowledgment. The display shows No acknowledge. If unsuccessful, a negative indicator tone sounds and your radio rejects to launch emergency mode. 2 To call, press and hold the PTT button. 3 To listen, release the PTT button. 8.4 Exiting Emergency Operation If an Emergency operation is triggered on your radio, the dispatch console, or radios configured as Supervisor can exit the Emergency operation. Radios configured as Supervisor can cancel emergency mode of other radios. The dispatch console must be programmed to use this feature. For more information, contact your system administrator. 55 MN009203A01-AD Chapter 8 : Emergency Operation Procedure:

To exit the emergency operation, press and hold the programmed Top (Orange) button. To exit the emergency operation as supervisor (Trunking only), use one of the following options:

Option Actions Exiting Emergency operation initiated by the Supervisor Perform one of the following actions:

- Press and hold the Top (Orange) button.

- Press and hold the 1-Dot Programma-

ble button. Press the Top (Orange) but-

ton.

- Wait for the console to clear the Emer-

gency. NOTE: Your radio supports the following button combinations:

- Radio 1-Dot Programmable button and Top (Orange) button.

- Radio 1-Dot Programmable button and accessory Orange button.

- Radio Top (Orange) button and accessory 1-Dot Button. 8.5 Remote Emergency The Remote Emergency feature allows you to remotely launch the emergency feature on a target radio. You can send the Remote Emergency request to radios from recently transmitted or received calls that are stored. 8.5.1 Sending Remote Emergency to Specific Users Procedure:

1 Press the programmed Remote Emergency button. 2 Select the required user of the target radio. 3 To send Remote Emergency, press the PTT button. If the ID of the target radio is valid, your radio displays sending notification and saves the ID as the last Remote Emergency ID. If the ID of the target radio is invalid, your radio displays an invalid ID notification. If your radio is in one of the following states, your radio plays a tone. Receive-only Channel Transmit Inhibit Out of Range Imbalance Coverage If your radio receives acknowledgment, your radio displays a positive notification. If your radio does not receive acknowledgment from the target radio, your radio displays a negative notification. 56 MN009203A01-AD Chapter 8 : Emergency Operation 8.5.2 Manually Refreshing the Remote Emergency List Procedure:

1 Press the programmed Remote Emergency button. 2 To refresh the remote emergency list, press Rfsh. Your radio displays List refreshed followed by the updated remote emergency list.. 8.5.3 Receiving Remote Emergency The remote emergency will only be launched if your radio has the emergency enabled. The receiving radio displays Emergency. Procedure:

To exit the emergency operation, press and hold the programmed Top (Orange) button. 8.6 Emergency Keep-Alive This feature prevents the radio from being turned off when it is in Emergency mode. If this feature is enabled, you are required to exit Emergency mode before turning off your radio. 8.7 Emergency Beacon When the radio is in Emergency mode, the Emergency Beacon feature transmits Bluetooth Low Energy (BTLE) signals and other Emergency information to nearby radios. Contact your system administrator for more information. 8.7.1 Sending Emergency Beacons The following method allows you to transmit the beacon. Procedure:

Press the programmed Top (Orange) button. 8.7.2 Receiving Emergency Beacons When you receive emergency beacon, the display shows Beacon Received, the transmitting radio ID, or alias. Procedure:

1 Perform one of the following actions:

To view the beacon list, press Details. To dismiss the beacon, press Dismiss. NOTE: If there are multiple beacons, the radio displays the recent beacon received. 57 MN009203A01-AD Chapter 8 : Emergency Operation 8.7.3 Viewing Received Emergency Beacon Procedure:

1 Press the Bcon menu item. NOTE: The received beacons are removed from the list after four minutes. 58 MN009203A01-AD Fireground Chapter 9 Fireground The portable Fireground Communications System is designed for deployment at an incident scene. It consists of central components that provide on-scene and in building radio coverage, and enhanced personnel accountability and monitoring:

Your APX portable radios Incident Management Software Command Terminal Radio Frequency (RF) Modem (Conventional Only) Control Channel Radio (Trunking) Optional Data Radio (Trunking) Accountability Server (Trunking) DVRS (Optional) If you have a critical situation, you can press the Emergency button, which activates an alarm on the Incident Management Software at the command terminal. The command terminal receives the following status updates from your radio:

Turning the radio on and off Automatic response to Polling Response to Evacuation commands Pressing the PTT button to make voice transmission Sending an Emergency Alarm and Call Entering or exiting a Trunking Talkgroup 9.1 Entering Fireground Zone Channel (Conventional) Prerequisites:

NOTE: If you are entering Fireground Trunking Talkgroup, ensure that the Fireground Trunking Talkgroup is selected. Procedure:

1 Cycle power your radio. 2 Press the Fireground Zone Channel menu item. 3 Listen for a transmission. 4 To call, press and hold the PTT button. 5 To listen, release the PTT button. 9.2 Responding to Evacuation Indicator When you receive an Evacuation Indicator, the radio shows the following indications:

59 MN009203A01-AD Chapter 9 : Fireground A tone sounds. The display shows the configurable programmed alert text and intelligent lighting. Procedure:

1 To respond, perform one of the following actions:

Press the 3-Dot Programmable button. If the radio is connected to the Remote Speaker Microphone (RSM), press the 1-Dot button on the RSM. Press the PTT button. NOTE: The PTT button must be configured in Customer Programming Software (CPS) to enable this function. The radio cancels the indications, a tone sounds, and the radio sends an acknowledgment to the command terminal. 9.3 Sending Evacuation Tone Procedure:

1 Press and hold the PTT button. 2 Press the Emergency button. A tone sounds when the Emergency button is released. The tone sounds in all radios within the talkgroup until the PTT button is released. NOTE: Radio does not transmit evacuation tone if the radio is in secure mode. 60 MN009203A01-AD Tactical Public Safety (Conventional Only) Chapter 10 Tactical Public Safety (Conventional Only) Tactical Public Safety (TPS) enables the member of a group to identify the start and the end of a transmission by displaying the caller name or ID on the radio display. 10.1 Using TPS Normal Transmission Procedure:

In the TPS Zone Channel, perform one of the following actions:

To talk, press and hold the PTT button. To listen, release the PTT button. Receive and listen to the call. The display shows the caller name or ID. 10.2 Using TPS Emergency Transmission Procedure:

1 Press the programmed Top (Orange) button. The Emergency Beacon tone sounds. 2 To call, press and hold the PTT button. 3 To listen, release the PTT button. The Emergency Call De-Key Sidetone sounds. After a short pause, the Emergency Beacon tone sounds. 4 To exit or cancel the Emergency mode, press and hold the programmed Top (Orange) button. 61 MN009203A01-AD Chapter 11 : Man Down (Fall Alert) Chapter 11 Man Down (Fall Alert) Man Down (Fall Alert) is a supporting feature of the Emergency operation. The Emergency feature must be programmed for Man Down (Fall Alert) to operate. Your radio activates the Man Down (Fall Alert) feature when it achieves or exceeds a tilt angle threshold or a combination of the angle threshold and radio motion below the motion sensitivity level. The radio must stay in this condition for a programmed period before the Emergency Alarm or Call is activated. NOTE: Because Man Down (Fall Alert) may be triggered accidentally, consider the following scenarios when using your radio:

If the radio is programmed to a horizontal position only, it must be worn in a vertical position. If the radio is programmed with the Man Down (Fall Alert) feature, turn off the radio when charging it with a wall-mounted charger. When you dismiss Man Down (Fall Alert) and keep the radio horizontal, no emergency will be sent and no further Man Down (Fall Alert) notification will occur until the device is rotated back to normal (portrait) mode. 11.1 Radio Alerts When Man Down (Fall Alert) is Triggered When Man Down (Fall Alert) is triggered, your radio plays an alert tone and the display shows Man Down. If the radio is programmed for Surveillance Mode, it inhibits all tones and lights including the Man Down (Fall Alert) tones. Man Down (Fall Alert) Enhanced Your radio also supports Man Down (Fall Alert) Enhanced where it plays an alert tone for a preprogrammed period. This tone is louder than the preprogrammed minimum level or the current level of the speaker and it acts as a beacon that helps to find the radio. NOTE: The radio plays this alert tone even in Surveillance Mode. When the alert tone is active, changing to another channel with a different setup triggers a different response from the radio:

The alert tone is inhibited when you change to a channel without Emergency feature. The alert tone is inhibited when you change to a channel with Emergency but no Man Down (Fall Alert) feature. The current alert tone is inhibited and is replaced with a different alert tone when you change to a channel with Emergency feature and a different Man Down (Fall Alert) configuration. The alert tone continues when you change to a channel with Emergency and similar Man Down

(Fall Alert) configuration. 11.2 Testing Man Down (Fall Alert) Prerequisites: Ensure that Man Down (Fall Alert) feature is configured in your radio. 62 MN009203A01-AD Chapter 11 : Man Down (Fall Alert) Procedure:

1 Turn on the radio, and place it in a vertical position for at least 5 seconds. 2 Lay the radio down in a horizontal position. Your radio shows the following indications:

Alert tone The display shows Man-Down. Postrequisites: If Man Down (Fall Alert) is configured but the condition does not trigger the activation of the feature, send the radio to a qualified technician. 11.3 Exiting Man Down (Fall Alert) Procedure:

To exit Man Down (Fall Alert) mode, press Clr. 11.4 Reinitiating Man Down (Fall Alert) Procedure:

To reinitiate Man Down (Fall Alert) after exiting Emergency Operation, perform one of the following actions:

Return the radio to a vertical position. If motion sensitivity is enabled, shake the radio. 63 MN009203A01-AD Chapter 12 : Secure Operations Chapter 12 Secure Operations Secure radio operation provides the highest commercially available level of voice security on both trunked and conventional channels. By default, the radio automatically enters the encrypted environment without having to manually select or clear the secure transmission. 12.1 Switching Between Secure and Clear Transmission Procedure:

1 To select Secure Transmission, press the programmed Secure/Clear side button. When you press the PTT button and the selected channel is programmed for clear only operation, your radio shows the following indications. A negative tone sounds. The display shows Clear TX only. The radio does not transmit until you set the Secure/Clear side button to clear mode. 2 To select Clear Transmission, press the programmed Secure/Clear side button. When you press the PTT button and the selected channel is programmed for secure only operation, your radio shows the following indications. A negative tone sounds. The display shows Secure TX only. The radio does not transmit until you set the Secure/Clear side button to secure mode. NOTE: If the Ignore Secure/Clear Switch When Strapped field is enabled, the radio transmits without displaying any messages in the strapped mode operation. The Secure/

Clear side button is only applicable when the radio is transmitting. 12.2 Encryption This chapter explains the encryption feature on your radio. NOTE: Contact your system administrator for more information. 12.2.1 Multikey Feature This feature allows the radio to be equipped with different encryption keys. There are two types of encryption keys:

64 MN009203A01-AD Chapter 12 : Secure Operations Conventional Multikey The encryption keys are strapped on a one-per-channel basis, through CPS. In addition, you can have operator-selectable keys, operator-selectable keysets, and operator-selectable key erasure. If talkgroups are enabled in conventional, then the encryption keys are strapped to the talkgroups. Trunked Multikey If both conventional and trunked applications are applied, strap the encryption keys for trunking on a per-talkgroup, or announcement-group basis. Also, a different key can be strapped to other features such as dynamic regrouping, failsoft, or emergency talkgroup. You can have operator-

selectable key erasure. 12.2.2 MDC OTAR (Conventional Only) This feature allows you to view or define the Motorola Data Communications (MDC) Over-the-

Air Rekeying (OTAR) features. It is applied only when operating in secure encrypted mode. In addition to Rekey Requests, OTAR transmissions include Delayed Acknowledgments, and Power-up Acknowledgments. Some of the selected options require configuration at the Key Management Controller (KMC) site to work properly. NOTE: This feature must be programmed by a qualified radio technician. 12.2.3 Infinite UKEK Retention This feature enables Unique Key Encryption Key (UKEK) to be permanently stored in the radio even when all the encryption keys are erased. Without this UKEK key, the radio cannot be rekeyed over the air. The Infinite UKEK Retention settings can be different for each secure profile. NOTE: This feature must be programmed by a qualified radio technician. 12.2.4 Hear Clear Hear-Clear is a noise reduction system which consists of Companding and Random FM Noise Canceller. Companding Reduces the channel noise, such as OTA transmission that is predominantly present in UHF2 and 900 MHz channel with the following features. Compressor Reduces the background noise flow and the speech signal at transmitting radio. Expander Expands the speech while the noise flow remains the same at receiving radio. Random FM Noise Canceller (Flutter Fighter) Reduces the unwanted effects of random FM noise pulses caused by channel fading under high Signal-to-Noise (S/N) conditions such as in a moving transportation. The fading effects, heard as audio pops and clicks, are canceled without affecting the desired audio signal. The Random FM Noise Canceller operates only in receive mode. NOTE: This feature must be preprogrammed by a qualified radio technician. Check with your dealer or system administrator for more information. 65 MN009203A01-AD Chapter 12 : Secure Operations 12.2.5 Loading Encryption Keys Procedure:

1 Attach the Key Variable Loader (KVL) to your radio. The display shows Keyloading. All other radio functions are locked, except power down, backlight, and volume. NOTE: If the Multisystem Over-the-Air Rekeying feature is in use, the ASTRO profile name is displayed below Keyloading. 2 Select the required keys and press Load on the KVL. The KVL indicates that key load is successful. 12.2.6 Selecting Encryption Keys Procedure:

1 Press the Key menu item. 2 Select the required key or enter the key number. 3 To save the new key, press Sel. If the selected key is not allowed, a tone sounds and the display shows Illegal key. If the selected key is erased, a tone sounds and the display shows Key fail. 12.2.7 Selecting Keysets This feature allows you to select one or a group of encryption keys from the available keys stored in the radio. Procedure:

1 Press the Kset menu item. 2 Select the required key. 3 To save the new keysets, press Sel. 12.2.8 Erasing Encryption Keys Procedure:

1 Select Eras. 2 Navigate to the encryption key or use the keypad to enter the key. 3 Select Optn. 4 Select the required option and select Sel. 5 To erase single key from the radio, select Erase single keys?Yes. 6 To erase all keys from the radio, select Erase all key?Yes. 66 MN009203A01-AD Chapter 12 : Secure Operations 12.2.9 Requesting Over-the-Air Rekey If the Multi-system Over-the-Air Rekeying feature is in use, the rekey request is only for the current selected secure profile. Prerequisites: Ensure that the Unique Key Encryption Key (UKEK) or Unique Shadow Key (USK) is loaded into the radio with the Key Variable Loader (KVL) before the rekey request can be sent. Refer to your local key management supervisor for more information. Procedure:

1 Press the Reky menu item. 2 Send the rekey request by pressing the PTT button. 3 To exit the feature and transmit in normal mode, press one of the following buttons:

PTT button Home button Top (Orange) button If the rekey operation fails, a negative tone sounds and the display shows Rekey fail. NOTE: The rekey operation failure indicates that your radio does not contain the UKEK or USK. 67 MN009203A01-AD Chapter 13 : Scan Chapter 13 Scan This feature allows you to monitor traffic on different channels by scanning a programmed list of channels. Scanning is halted if you initiate a call and resumes when the call has ended. 13.1 Turning Scan On or Off Procedure:

Turn scan on or off by pressing the Scan menu item. If the scan is enabled, the display shows Scan On and the Scan status icon. If the scan is disabled, the display shows Scan Off. 13.2 Making Dynamic Priority Change (Conventional Scan Only) While the radio is scanning, the dynamic priority change feature allows you to temporarily change any channel in a scan list (except for the Priority-One channel) to the Priority-Two channel. This change remains in effect until scan is turned off. Scan then reverts to the default setting. Procedure:

When the radio locks onto the channel designated as the new Priority-Two channel, press the programmed Dynamic Priority button. The radio continues scanning the remaining channels in the list. 13.3 Deleting Nuisance Channel Procedure:

1 Identify the nuisance channel. 2 Press the Nuis menu item. The radio continues scanning the remaining channels in the list. NOTE: This feature is not applicable for priority channels, or the designated transmit channel. 13.4 Restoring Nuisance Channels Procedure:

To restore the deleted nuisance channel, perform one of the following actions:

Stop and restart a scan. Mode change to another channel, and return to the original channel. 68 Turn off the radio and then turn it on again. MN009203A01-AD Chapter 13 : Scan 69 MN009203A01-AD Chapter 14 : Scan Lists Chapter 14 Scan Lists Scan lists are created and assigned to individual channels or groups. Your radio scans for voice activity by cycling through the channel or group. The sequence of scan is as specified in the scan list for the current channel or group. Your radio supports different types of Scan Lists:

Conventional Scan List Talkgroup Scan List Trunking Priority Monitor Scan List Refer to a qualified radio technician for the maximum number of Scan Lists to be programmed in your radio. 14.1 Managing the Scan List Procedure:

1 Press the SCNL menu item. 2 Manage the scan list by using the following options:

Option Actions Viewing the scan list At the Edit Scan screen, view the scan list by scroll-

ing through the list. Adding a channel into the scan list At the Edit Scan screen, press Sel. Removing a channel from the scan list The currently highlighted channel is added into the scan list. a At the Edit Scan screen, scroll to the required channel. b Press Del. Recalling the next channel in the scan list At the Edit Scan screen, press Rcl. The display auto scrolls to the next channel in the scan list. 70 MN009203A01-AD Connectivity Chapter 15 Connectivity This section explains the management of connections between your radio and a variety of networks and other devices. 15.1 SmartConnect Before switching broadband connections, your radio compares the relative signal strength of the various broadband connection types to one another, as well as Land Mobile Radio (LMR). Your radio remains or returns to LMR connection when the other broadband connections fall below the quality threshold. A radio operating on a lower priority broadband connection returns to the higher priority or quality connection while idle on SmartConnect. Your radio displays the SmartConnect capable icon on the SmartConnect enabled channel. When connected to an available network, your radio displays SmartConnect connection icon

. NOTE:

This feature must be programmed by a qualified radio technician. For more information, contact your system administrator. 15.2 Wi-Fi You can connect your radio to a Wi-Fi network for wireless programming. Your service administrator preprograms the Wi-Fi Service Set Identifier (SSID) or network name that your radio can connect to. This feature is enabled by default on your radio. NOTE: Channel 12 and 13 are enabled for Wi-Fi for all countries except US and Canada. 15.3 Bluetooth This feature allows your radio to extend its functionality by connecting to external proprietary Motorola Solutions accessories. Use Motorola Solutions proprietary Mission Critical Wireless (MCW) devices with APX radios during Mission Critical operations. Other Bluetooth devices may or may not meet the mission critical standard. Your radio supports the following Bluetooth enabled devices or profiles:

Headset (HSP) Dial Up Networking (DUN) Personal Area Networking (PAN) Serial Port (SPP) General Attribute Profile (GATT) 71 MN009203A01-AD Chapter 15 : Connectivity 15.3.1 Turning Bluetooth On or Off Procedure:

1 Press the BT menu item. 2 Select Status. 3 Perform one of the following actions:

To turn on Bluetooth, press On. To turn off Bluetooth, press Off. 15.3.2 Searching and Pairing the Bluetooth Device Prerequisites: Ensure that the Bluetooth on your device is turned on and set to Discoverable in order to enable your radio to detect your device in Bluetooth. Procedure:

1 Press the BT menu item. 2 Press Search DevicesOn. 3 To pair with an available device, select the required device and press Sel. The radio pairs to the device. 15.3.3 Turning Bluetooth Audio On or Off NOTE:

Bluetooth audio routing can be configured in the Customer Programming Software (CPS) to route the audio to the radio internal speaker. The audio routes to the radio speaker if the radio Remote Speaker Microphone (RSM) is not connected. For more information, contact your system administrator. Procedure:

1 Press the BT menu item. 2 Select Bluetooth spkr. 3 Perform one of the following actions:

To turn on Bluetooth audio, press On. To turn off Bluetooth audio, press Off. 15.3.4 Viewing and Clearing the Bluetooth Enabled Device Information Procedure:

1 Press the BT menu item. 2 Select Devices and press Sel. 72 MN009203A01-AD Chapter 15 : Connectivity 3 To view the status of devices that are paired or connected, scroll through the list of <Device Friendly Name>. If there are no active Bluetooth devices paired or connected, the display shows No devices. 4 To clear a device from the list, select the required device and press ClrYes. 15.4 ASTRO 25 (P25) Programming Over Project 25 (POP25) Also known as Over-the-Air Programming, this feature allows configuration data and firmware to be upgraded to your radio over-the-air. Full use of the radio is retained during the data transfer without interrupting communication. If the upgrade happens on the ASTRO 25 and ASTRO Conventional systems, the upgrade pauses to give priorities to voice call, and continues after the voice call ended. If the upgrade happens on a Wi-Fi network, the upgrade process runs concurrently with voice calls. Once a configuration upgrade is downloaded to your radio, you can install new changes immediately, or delay changes to be installed on the radio when it is being powered up. Your radio can also be configured to allow you to accept or reject an upgrade. 15.4.1 Responding to Upgrade Notifications The display shows Upgrade? and a tone sounds every 30 seconds until you accept, delay, or reject the request. NOTE: Do not remove the power cable or turn off the radio during the firmware upgrade process. If your radio has problems upgrading over-the-air, consult a qualified technician for details. Procedure:

Respond by performing one of the following actions:

To accept the upgrade request, press Acpt. To delay the upgrade request, press Dlay. To reject the upgrade request, press Rej. One of the following scenarios occurs:

If you choose to accept, the display shows Programming Dont power off. The radio resets to install the upgrade. NOTE: The radio cannot be used while the upgrade is being installed. You must ensure to accept the upgrade at a convenient time. If you choose to delay, a configuration data upgrade is installed automatically at the next power up. In the case of a firmware upgrade, the radio prompts Upgrade? again at the next power up. If you choose to reject, the display shows Upg Aborted. The radio continues to function with the current configuration until it gets reprogrammed. 73 MN009203A01-AD Chapter 16 : Location Chapter 16 Location The Global Navigation Satellite System (GNSS) in the radio integrates information from the Global Positioning System (GPS) to determine the approximate geographical location of your radio. NOTE: The Location feature is addressed as Global Positioning System (GPS) across the manual as the naming convention of the buttons and strings remain the same as the legacy feature of GPS. The availability and accuracy of this location information and the calculation duration can vary depending on the environment in which you are using the GPS feature. For example, GPS location fixes are difficult to obtain indoors, in covered locations, between high buildings, or in situations where you have not established a clear broad view of the sky. If adequate signals from multiple satellites are available, your GPS feature only provides an approximate location, usually within 10 meters from your actual location, but sometimes farther away. Sometimes, the GPS feature cannot complete a location calculation successfully. You will then see a message indicating that your radio cannot connect to enough visible satellites. To maximize the ability of your radio to determine a fix, take note of the following guidelines:

For your initial fix, hold the radio in the face position. Stay in the open as the GPS feature works best when there is nothing between your radio and the open sky. 16.1 Turning Location On or Off Procedure:

1 Press the Loc menu item. 2 Perform one of the following actions:

To turn on Location, press OptnTurn On GPSSel. To turn off Location, press OptnTurn Off GPSSel. 16.2 Accessing Location Procedure:

1 Press the Loc menu item. 2 Press OptnTurn On GPSSel. 3 To check the last successful location fix, select the longitude, time, and date. 4 To access the current location, press Rfsh. 5 To return to the Home screen, press Exit. If the radio successfully obtains the current location, the display shows the following information:

Current Location 74 MN009203A01-AD Chapter 16 : Location UTC (Zulu) Time Date NOTE: If the location signal is present, the location coordinates are automatically updated every five seconds. If the radio fails to obtain the current location, the display shows No service and returns to the previous screen. 16.3 Selecting Location Formats The Location Format feature allows you to select different display formats of the Global Positioning System (GPS) location. The following GPS location formats are available:

Lat/Long(DD) Lat/Long(DDM) Lat/Long(DMS) UTM/UCS SLD99 MGRS NOTE: When you send your location to another radio, the receiving radio displays the location in its selected format. Procedure:

1 Press the Loc menu item. 2 Press OptnLoc FormatSel. 3 Select the required location format. The display shows the location with the selected format. NOTE:

If the SLD99 format is selected and the range is invalid, the display shows on the location. This situation occurs when you use the radio outside of Sri Lanka. To correct this situation, switch the location display format to other GPS options such as DDM, DMS, UTM/UCS, or MGRS. 16.4 Managing Waypoints Prerequisites: Ensure that your radio displays the current location. Procedure:

1 Press the Optn menu item. 2 Press WaypointsSel. 3 Manage waypoints by using the following options:

Option Viewing waypoints Actions a Scroll to the required waypoint from the list. b Press OptnViewSel. 75 MN009203A01-AD Chapter 16 : Location Option Actions The display shows the following information of the selected waypoint:

Military Grid Reference System (MGRS) or, lati-

tude and longitude location Time Date Deleting a waypoint a Scroll to the required waypoint from the list. Deleting all waypoints b Press OptnDeleteSelYes. The display shows a positive notification. a Scroll to any waypoint from the list. b Press OptnDelete AllSelYes. The display shows a positive notification. NOTE: You cannot delete any of the pro-

grammed waypoints. 4 Return to the Home Screen by pressing the Home button. 16.5 Location Feature in Emergency Mode When the Emergency feature is activated, the radio exits the Location menu and returns to the Home screen. You can view the channel that triggers the emergency signal. You can reenter the Location menu while still in Emergency mode as long as Silent Emergency is not activated. If you have disabled the Location feature on your radio, it automatically turns back on when Emergency mode is activated. If there is a solid location signal during Emergency operation, the current location and the location information received is saved as Emergency and Last Known Location respectively. 16.6 Peer-Location on the Display (ASTRO Conventional) This feature is only available for radio-to-radio voice transmissions, dispatch call, and selective call. The transmitting radio and receiving radio must be configured to enable the sending and receiving of the Global Positioning System (GPS) coordinates. NOTE: If the receiving radio is operating in a Mixed Mode channel and the voice transmission is from the conventional ASTRO system, the radio can only receive the peer-location coordinates. This feature is operable in a Scan Active channel, or Scan Talkback channel. After receiving a voice transmission with GPS coordinates enabled on the receiving radio, the display shows the available full location, or short location coordinates. Full location coordinates PTT ID (optional) 76 MN009203A01-AD Chapter 16 : Location Longitude and latitude Relative distance or direction Short location coordinates PTT ID (optional) Longitude and latitude NOTE:

If the transmitting radio is stale at the location after a period of time, the receiving radio display shows the last known location. If the transmitting radio does not have GPS, or the receiving radio could not decode the GPS signal of the received signal, the receiving radio display shows the location as unknown. 16.7 MGRS Coordinates Military Grid Reference System (MGRS) can only be enabled through Customer Programming Software (CPS) configuration. When the MGRS coordinate is enabled, all location coordinates are displayed in the MGRS format, including the editable locations in GPS. 77 MN009203A01-AD Chapter 17 : Mission Critical Geofence (ASTRO 25 Trunking) Chapter 17 Mission Critical Geofence (ASTRO 25 Trunking) This feature allows the radio to use the Global Positioning System (GPS) receiver to determine its location at frequent intervals and evaluate if the radio is within the Geofence area in real time. Geofence is a virtual perimeter based on the GPS to define a geographical area on earth. When the radio enters the predefined Geofence area, your radio receives the Dynamic Regroup command from the system and immediately connects to a Dynamic Regroup talkgroup. The radio display shows the new selected Dynamic Regrouped talkgroup with green intelligent light for your attention. Voice Announcement is also available to support this feature. Any new text messages received at Geofence is displayed immediately on the radio display. NOTE:

If the radio is set up in Digital Vehicular Repeater System (DVRS), only mobile radio is supported for this feature. The user navigation for this feature is not available for this model. 17.1 Entry to the Geofence Area The Voice Announcement and Text Messaging Service (TMS) display in this feature are optional. These features must be configured to enable you to hear, and see these indicators. When the radio enters a Geofence area, the radio immediately sends a message ACK back to the system. The radio searches the current zone for the channel with same talkgroup assigned as the Dynamic Talkgroup and also with same system ID of current trunk system. Once matched, the radio display shows the first matched and connected channel alias. If there is no channel with matching Talkgroup ID and trunk system ID, the radio display shows the channel alias of <DYNAMIC talkgroup>. Once the radio is connected, you hear a dynamic regroup tone. The radio display shows

<DYNAMIC channel>. The radio display shows the green intelligent backlight, and you hear a Voice Announcement. NOTE:

When the radio loses the Global Positioning System (GPS) signal, the GPS icon blinks and the radio sounds two high-pitched tones repetitively to indicate that the GPS has failed to operate. The radio display shows the red intelligent light. If the first matched channel is not configured with Voice Announcement, no Voice Announcement is played. The system sends a message to your radio. The radio display shows a direct text message content without any user operation. This message indicates that you are currently present in a Geofence area. This TMS remains open on the display until you press exit or home to exit this screen. NOTE: If there is another incoming text message before you exit the previous message, the message screen is refreshed to show the latest message. 78 MN009203A01-AD Chapter 17 : Mission Critical Geofence (ASTRO 25 Trunking) When the radio exits the Geofence area, your radio reverts to original channel or newly assigned talkgroup. The radio display shows the new channel together with Voice Announcement to indicate the changes. Voice Announcement of the new channel only works if that channel is configured with Voice Announcement. 17.2 Entry to Mission Critical Geofence When the radio enters the predefined Geofence area, the radio displays <Geofence Alias>. The radio display also shows the intelligent backlight, and you hear a Voice Announcement. Zone and channel alias of the Geofence area is displayed. If the radio is set to manual, you can choose either to proceed with zone and channel change, or cancel the change. The radio then connects to the designated talkgroup. The radio displays the talkgroup alias and dynamic regroup tone sounds. The level changes for transmit power and, your radio shows a direct text message content without any user operation. NOTE:

The availability of the Voice Announcement (VA), Text Messaging Service (TMS) display, Intelligent Backlight, and Transmit Power Level alerts depend on your radio configuration. The VA can be programmed to alert continuously, or momentarily. If Site Selectable Alert (SSA) is enabled, the radio mutes any alert that is received when entering the Geofence area, and unmutes when exiting. 17.3 Exit from Mission Critical Geofence When the radio exits the Geofence area, the radio reverts to the original transmit power level, intelligent lighting, channel, or newly assigned talkgroup. Voice announcement (VA) is canceled or you hear a programmed VA tone. The radio displays the new channel, and a message is received to indicate the changes. 79 MN009203A01-AD Chapter 18 : Contacts Chapter 18 Contacts This feature provides address-book capabilities on your radio. Each entry corresponds to an alias

(name) and ID (number) that you use to initiate a call. Contact entries are alphabetically sorted according to the entry alias. Each entry, depending on context (conventional, trunking, or phone), associates with one to five IDs according to the following types of calls:

Phone Call Private Call Selective Call Call Alert Each entry within Contacts contains the following information:

Call Alias (Name) Call ID (Number) Call Type (Icon) WACN ID (ASTRO 25 Trunking IDs only) System ID Your radio also supports a maximum of 50 call lists. Each list can store up to 100 IDs. NOTE: Your radio is programmed with a few contacts per Call Lists. Check with your dealer or system administrator for more information. 18.1 Viewing Contact Details Procedure:

1 Press the Cnts menu item. 2 Select the required contact. 3 Press OptnViewSel. 80 MN009203A01-AD Recent Calls Chapter 19 Recent Calls Recent call menu allows you to view the recent incoming and outgoing call information. You can view the information of the following type of calls:

Call Alert Selective Call Private Call Phone Call (Outgoing Only) Emergency Call (Incoming Only) NOTE: The Log Dispatch Calls Enable field need to be enabled in Customer Programming Software (CPS) for your radio to log the dispatch call. 19.1 Viewing Recent Calls Procedure:

1 Press the Rcnt menu item. 2 To view recent Emergency Calls, press Emer. 3 To return to all recent calls, press All. 19.2 Deleting Calls This feature allows you to delete calls from the Recent Calls list. Procedure:

Delete calls by using the following options:

Option Deleting all calls Deleting non-emergency calls Actions a Press Optn. b Select Delete Calls. c Select All Calls. d Press Yes. a Press Optn. b Select Delete Calls. c Select Non-Emer Calls. d Press Yes. When you have successfully deleted all calls, your display shows All calls deleted and the Recent Calls list is empty. 81 MN009203A01-AD Chapter 19 : Recent Calls When you have successfully deleted non-emergency calls, your display shows Non-emer calls deleted and the Recent Calls list only contains emergency calls. 82 MN009203A01-AD Sending Status Chapter 20 Sending Status You can send status messages to the dispatcher. A status transmission makes more efficient use of a channel as compared to a voice transmission. Procedure:

1 Press the programmed Status button. 2 Select the required status. 3 To send the status, press the PTT button. If acknowledgement is received, your radio shows the following indications:

Four tones sound. The display shows Ack received. If acknowledgement is not received, your radio shows the following indications:

A tone sounds. The display shows No acknowledge. 83 MN009203A01-AD Chapter 21 : Call Alert Paging Chapter 21 Call Alert Paging This feature allows your radio to work like a pager. If other users are away from their radios or if they are unable to hear their radios, you can send them an individual call alert page. You can also verify if a radio is active on the system. If there is no answer after the maximum ring time or when you press the PTT button for an Enhanced Private Call, the radio automatically sends a call alert page. NOTE: This feature must be programmed by a qualified radio technician. 21.1 Sending Call Alert Page Prerequisites: Ensure that your radio is programmed to support this feature. Procedure:

Send a call alert page using one of the following options:

Option Page Menu Call Menu Actions a Press the Page menu item. b Press Cnts. c To send the page, press the PTT button. a Press the Call menu item. b Press Cnts. c Select the ID or alias. d To initiate the call, press the PTT button. If the target radio does not respond after a program-

med period, the display shows Send page?. Press Yes. The display shows Paging...<Number>. If the call alert page is sent successfully, your radio shows the following indications:

- A tone sounds.

- The display shows Ack received and the radio returns to the Home screen. If the call alert page is not acknowledged, your radio shows the following indications:

- A tone sounds.

- The display shows No acknowledge. 84 MN009203A01-AD Chapter 21 : Call Alert Paging 21.2 Receiving Call Alert Page When you receive a Call Alert page, your radio shows the following indications:

A tone sounds. The green LED illuminates. The display shows Page received. Procedure:

Press any button to clear the Call Alert page. 85 MN009203A01-AD Chapter 22 : Automatic Registration Service Chapter 22 Automatic Registration Service Automatic Registration Service (ARS) provides an automated data application registration for your radio. When you turn on the radio, the device automatically registers with the server. Data applications within the fixed network determine the presence of a device on the system and send data to the device. The ARS consists of the following mode:

ARS Server Mode (Default mode) ARS Non-server Mode 22.1 Selecting ARS Mode Procedure:

Select the Automatic Registration Service (ARS) Mode by using one of the following options. Option Actions Selecting ARS Mode using the Frequency knob Rotate the programmed Channel Selector knob when the radio displays the required zone. Selecting ARS Mode from the menu a Press the Chan menu item. b Select the required channel or mode and press Sel. The display shows the User Login Indicator icon, the zone, and the ARS server channel mode. NOTE: If the selected channel or mode is not programmed, the display shows Unprogrammed. 86 MN009203A01-AD User Login Feature Chapter 23 User Login Feature This feature allows you to take on a friendly username such as Text Messaging Service (TMS). You can still send text messages without logging in as a user. The user login feature only enables the recipient of your message to identify you as the sender by assigning a username to your message. This feature is only applicable for Land Mobile Radio (LMR) Messaging. NOTE: A predefined username that is set more than the maximum allowed characters is an invalid name. 23.1 Logging In or Out of the User Login Feature Logging In the User Login Feature Procedure:

1 Press the User menu item. 2 Scroll to the predefined user name that is required. 3 Select the predefined user name by pressing Logn. 4 To cancel the login process and return to the initial user login screen, press Back. If the login process is successful, the radio shows the following indications:

The display shows the User Login Indicator (IP Packet Data) icon. The display shows a positive notice. If the username is invalid or the login process is unsuccessful, the radio shows the following indications:

The display shows a blinking User Login Indicator (IP Packet Data) icon. The display shows a negative notice. In the non-Automatic Registration Service (ARS) Mode, the display shows Offline. Logging Out of the User Login Feature NOTE: Private data refers to all messages in the text messaging folder. The next user is able to access the messages if private data is not deleted. Prerequisites: You are logged on or using Offline Mode. Procedure:

1 Press the Logt menu item. One of the following scenarios occurs:

If the display shows Clear private data?, proceed to the next step. If the Delete Messages On Session End feature is enabled, the radio clears the private data. The radio then returns to the User Login screen. 87 MN009203A01-AD Chapter 23 : User Login Feature 2 Perform one of the following actions:

To clear all your private data, select Yes. To keep your private data, select No. 88 MN009203A01-AD Text Messaging Service Chapter 24 Text Messaging Service Text Messaging Service (TMS) allows you to send and receive messages and run database queries directly from your radios. The maximum number of characters allowed for a text message is 200 characters. The types of text messages available are:

A predefined message (quick text message). A query (ASTRO 25 Advanced Messaging Solution). 24.1 TMS Status Icons Text Messaging Service (TMS) icons appear on the radio display when you send and receive text messages. Table 13: TMS Status Icons Icon Name Description New Message The radio receives a new message. The selec-

ted text message in the inbox is not read. Inbox Full The inbox is full. Message Request Reply Urgent Message The message requires a reply. The Request Reply feature is toggled on before the message is sent. The message is urgent. The Priority feature is toggled on before the message is sent. Urgent Message with Request Reply The message is urgent and requires a reply. The Priority and Request Reply feature is tog-

gled on before the message is sent. Table 14: TMS Inline Icons Icon Name Description Message Read The selected text message in the inbox is read. Message Unread The selected text message in the inbox is not read. Message Sent The text message is sent. 89 MN009203A01-AD Chapter 24 : Text Messaging Service Icon Name Description Message Unsent The text message cannot be sent. 24.2 Accessing Messages Quick Text messages are messages that are predefined and usually consist of messages that are used most frequently. Each Quick Text message has a maximum length of 50 characters. You can select the required text from the Quick Text. Procedure:

Access the messaging feature by using the following options. Option Actions Sending Quick Text Messages Viewing Text Messages Replying to Text Messages a Press the TMS menu item. b Press ComposeSel. c Scroll to the required predefined message. d Press OptnSend MessageSel. e Scroll to the required address and press Sel. a Press the TMS menu item. b Press InboxSel. c Scroll to the required ID or alias, and press Sel. a At the Inbox screen, scroll to the required ID or alias, and press SelRply. b Scroll to the required Quick Text. c Send the message by pressing OptnSend MessageSel. Deleting a Text Message a At the Inbox or Sent screen, scroll to the re-

quired message. b Press Del. Deleting All Text Messages a Press the TMS menu item. b Depending on the required folder, press either Inbox or Sent. c Press ClrYes. 90 MN009203A01-AD Monitor Feature Chapter 25 Monitor Feature The monitor feature ensures that a channel is clear before transmitting. The lack of static on a digital channel when you switch from analog to digital radios is not an indication that the radio is malfunctioning. Digital technology quiets the transmission by removing the noise from the signal and allows only the clear voice or data information to be heard. 25.1 Monitoring Channels Procedure:

Depending on your preference and programmed functions, monitor channels by using one of the following options. Option Actions Monitoring channels using the Moni-

tor button a Press the programmed Monitor button. b If necessary, adjust the Volume Control Knob. c To transmit, press and hold the PTT button. d To listen, release the PTT button. The Carrier Squelch indicator appears on the dis-

play when you monitor a channel using the pro-

grammed Monitor button. Monitoring channels using the selec-

ted zone channel a Select the desired zone and channel. b Listen for a transmission. c If necessary, adjust the Volume Control Knob. d To transmit, press and hold the PTT button. e To listen, release the PTT button. 25.2 Monitoring Conventional Mode This feature allows you to monitor channel traffic on conventional channels by defeating the coded squelch. This way, you can listen to another active user on the channel and you do not take over the conversation of another user. Prerequisites: Ensure that your radio is programmed to receive Private-Line (PL) calls. Procedure:

1 Press the Monitor button to listen for activity. The Carrier Squelch indicator appears on the display. 2 Set continuous monitor operation by pressing and holding the Monitor button. The duration of the button press is programmable. 91 MN009203A01-AD Chapter 25 : Monitor Feature 3 To return to the original squelch setting, press the Monitor button again or the PTT button. If you try to transmit on a receive-only channel, you hear an invalid tone until you release the PTT button. 92 MN009203A01-AD Remote Monitor Chapter 26 Remote Monitor This feature allows the system administrator to turn on the microphone of a targeted radio with a subscriber alias or ID. When remote monitor feature is activated, the audio transmission can be configured in Customer Programming Software (CPS) to route the audio to the radio internal microphone, wired Remote Speaker Microphone (RSM), or Bluetooth wireless microphone. In life-threatening or critical situations, the system administrator can remotely monitor any audible activity surrounding the targeted radio. 93 MN009203A01-AD Chapter 27 : Transmit Inhibit Chapter 27 Transmit Inhibit The Transmit Inhibit feature allows you to stop all transmission including voice and data. The radio can receive messages but is not able to reply the acknowledgment request of the received message. This feature is available for APCO 25 Trunking, Type II Trunking, and Conventional operations for all APX radios. You can physically control the transmission of the radio especially during operation in hazardous environments. An environment is considered hazardous if radio transmission could initiate an explosion or other dangerous reactions. 27.1 Enabling or Disabling Transmit Inhibit Procedure:

To enable or disable transmit inhibit, press the TxIn menu item. If Transmit Inhibit is enabled, your radio shows the following indications:

A tone sounds. The display shows Tx inhibit on. NOTE: If you press the PTT button, a negative tone sounds. If Transmit Inhibit is disabled, your radio shows the following indications:

A tone sounds. The display shows Tx inhibit off. NOTE:

The status of the Transmit Inhibit does not change after the radio powers up. 27.2 Smart PTT (Conventional Only) Smart PTT is a per-personality, programmable feature used to keep radio users from talking over other radio conversations. When Smart PTT is enabled in your radio, you cannot transmit on an active channel. The following table shows the variations of Smart PTT. Mode Description Transmit Inhibit on Busy Channel with Carrier Transmit Inhibit on Busy Channel with Wrong Squelch Code You cannot transmit if traffic is detected on the channel. You cannot transmit on an active channel with a squelch code or (if secure-equipped) encryption key other than your own. If the PL code is the same as yours, the transmission is not preven-

ted. 94 Mode Description MN009203A01-AD Chapter 27 : Transmit Inhibit 95 MN009203A01-AD Chapter 28 : Dynamic Regrouping (Trunking Only) Chapter 28 Dynamic Regrouping (Trunking Only) This feature allows the dispatcher to temporarily reassign selected radios to a particular channel to communicate with each other. When your radio is dynamically regrouped, it receives a dynamic regrouping command and automatically switches to the dynamically regrouped channel. You hear a tone and the display shows the name of the dynamically regrouped channel. When the dispatcher cancels dynamic regrouping, the radio automatically returns to the previous zone and channel. If you access a zone or channel that has been reserved as a dynamically regrouped mode for other users, you hear an invalid tone. 28.1 Classification of Regrouped Radios The dispatcher can classify regrouped radios into Select Enabled or Select Disabled categories. Select Enabled Select-enabled radios are free to change to any available channel, including the dynamic-

regrouping channel, once you have selected the dynamic-regrouping position. Select Disabled Select-disabled radios cannot change channels while dynamically regrouped. The radio is forced to remain on the dynamic-regrouping channel. The Scan and Private Call features are unavailable when your radio is Select Disabled. 28.2 Requesting a Reprogram (Trunking Only) You can notify the dispatcher when you want to reprogram a new dynamic regrouping assignment. Procedure:

To send a reprogram request to the dispatcher, press the Rpgm menu item. If the dispatcher acknowledges the reprogram request, your radio shows the following indications:

Five beeps sound. The display shows a positive notification. Your radio returns to the Home Screen. If the dispatcher does not acknowledge the reprogram request in six seconds, your radio shows the following indications:

A tone sounds. The display shows a negative notification. 96 MN009203A01-AD Dynamic Zone Programming Chapter 29 Dynamic Zone Programming Dynamic Zone Programming (DZP) provides one or more Dynamic Zones to store frequently used channels for conventional or trunking. NOTE: Your radio must be programmed for you to use this feature. At least one zone in the radio must be a nondynamic zone. 29.1 Selecting Channels in the Dynamic Zone Procedure:

1 Enter a dynamic zone by performing the following actions:

a Press the Zone menu item. b Select <# Dynamic Zone Channels> and press Sel.

# indicates the channel number on the 16-Position Switch that is numbered from 1 to 16. 2 Press the ZnPr menu item. 3 Press EditList SelectionSel. 4 Scroll to the required zone and press Sel. 5 Scroll to the required channel and press Sel. The display shows a positive notification and the channel is added to the Dynamic Zone. 29.2 Deleting Channels in the Dynamic Zone Procedure:

1 Enter a dynamic zone by performing the following actions:

a Press the Zone menu item. b Select <# Dynamic Zone Channels> and press Sel.

# indicates the channel number on the 16-Position Switch that is numbered from 1 to 16. The radio returns to the Home screen and displays the selected Dynamic Zone Channel. 2 Press the ZnPr menu item. 3 Select the required saved dynamic channel and press Del. 4 To return to the Home screen, press Exit. The Home screen shows <Dynamic Zone Channels>. If the deleted channel is the home channel, the Home screen shows <Zone Name>Blank. 97 MN009203A01-AD Chapter 30 : Zone-to-Zone Cloning Chapter 30 Zone-to-Zone Cloning Zone Cloning clones conventional zones from one radio to another. You can select the followings zones from a source radio and clone them into a target radio. Clone enabled zones Dynamic Zones Multiple Private Line (MPL) You can clone the zones by connecting the source radio and target radio with a clone cable. The target radio must be digital, band, and FCC mandate compatible with the source radio. NOTE: This feature is applicable for Full Keypad models and Limited Keypad models. 30.1 Cloning Zones Procedure:

1 Press the Clon menu item. 2 Press Sel. If successfully connected to the target radio, the radio displays Target radio connected. 3 To accept the source zones selection, press Next. 4 Perform one of the following actions:

If you select a single source zone, press Sel to select the target zones for cloning. If you select multisource zones, the display shows Confirm target and the automatically selected target zones and source zones mapping. If the selected multi-source zones exceed the last clone target zone, the radio displays <#>

src zones unselected, Sel exceed max tgt zone, and Protected tgts not supported alternatively. 5 To begin cloning, press Clon. If cloning is successful, your radio shows the following indications:

A tone sounds. The display shows Clone successful and the source zone alias. If cloning is unsuccessful, your radio shows the following indications:

A tone sounds. The display shows Clone failed. NOTE: The target radio enters programming mode during cloning and resets when cloning is completed. 98 MN009203A01-AD Radio Kill Chapter 31 Radio Kill This feature allows you to render your radio or another radio inoperable if the radio is misplaced or lost. When a radio is killed, the display turns blank and all functions of the radio are not usable. The killed radio can only be recovered with a special device. Consult an authorized and qualified technician for details. 31.1 Using Direct Kill to Kill Your Own Radio Procedure:

1 Press and hold the 2-Dot Programmable button. 2 Press the Top (Orange) button until the display turns blank and becomes inoperable. 99 MN009203A01-AD Chapter 32 : Radio Inhibit Chapter 32 Radio Inhibit This feature allows the system administrator to put a radio into a nonfunctional state when the radio is missing or in an unknown hand. The radio stays in this state regardless of its power changes. NOTE:

If the radio has Intersystem roaming capability, the system administrator is able to put the radio into a nonfunctional state when the missing radio roams to another system. The radio can only be uninhibited by receiving an uninhibited command from the system administrator. 100 MN009203A01-AD Switching between Repeater and Direct Operation Chapter 33 Switching between Repeater and Direct Operation Repeater operation increases radio coverage area by connecting with other radios through a repeater. Direct or "talkaround" operation bypasses the repeater and connects directly to another radio. You can select either one of these operations on your radio. Procedure:

Perform one of the following actions:

Press the programmed Repeater/Direct button. From the Home screen, press the Dir menu item. 101 MN009203A01-AD Chapter 34 : Voice Announcement Chapter 34 Voice Announcement This feature enables the radio to audibly indicate the current feature mode, zone, or channel assigned to the user. The available voice announcement (VA) priority options are:

High Voice announcement is enabled even when the radio is receiving calls. Low Voice announcement is disabled when the radio is receiving calls. NOTE: If the Voice Announcement field is set to Enabled, after an interruption by a momentary tone one of the following scenarios occurs:

If Suppress Replay field is Enabled, voice announcement replays. If Suppress Replay field is Disabled, voice announcement turns off. 102 MN009203A01-AD Site Selectable Alerts Chapter 35 Site Selectable Alerts A Site Selectable Alert (SSA) is an Intelligent Lighting indicator with audio alert. The alert is sent to radios at sites to notify the users when special situations occur. Your radio supports up to 250 site aliases. Only authorized radios are enabled to send SSA. NOTE:

The alert alias, alert tone, and alert period are configured in the Customer Programming Software. Contact your system administrator for more information. The SSA alert volume is reduced when voice audio is received at the same time. It is important that the SSA audio file is created with clear loud audio to ensure audio clarity at reduced levels. 35.1 Sending Site Selectable Alert Notification If you are receiving an alert notification, your radio shows the following indications:

Alert tone repeats periodically. The display shows the alert alias with intelligent lighting on the home screen. Procedure:

1 Press the SSA menu item. 2 Select Start Alert and pressSel. 3 Perform one of the following actions:

To send alert notifications to a single site, select the required site alias and press Sel. To send alert notifications to all sites, select [All Sites] and press Sel. To send alert notifications to all available sites, select [All Avail] and press Sel. 4 Select the required alert alias. 5 Select Send. The display shows Sending req. If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows Req failed. If the request is successful, the display shows Req successful. If one or more sites are unavailable, the display shows Not all sites available. 35.2 Stopping Site Selectable Alert Notification Procedure:

1 Press the SSA menu item. 2 Press Stop AlertSel. 3 Perform one of the following actions:

To stop alert notifications of a single site, select the required site alias. 103 MN009203A01-AD Chapter 35 : Site Selectable Alerts To stop alert notifications of all sites, select [All Sites]. To stop alert notifications of all available sites, select [All Avail]. 4 Press Send. 5 To return to the Home screen, press Exit. The display shows Sending req. If radio is out of range, roaming to a foreign system or in a failsoft situation, the display shows Req failed. If the request is successful, the display shows Req successful. If the site is not available, the display shows <Site Alias> not available. If the site does not exist, the display shows <Site Alias>does not exist. 104 MN009203A01-AD Additional Performance Enhancement Chapter 36 Additional Performance Enhancement The following performance enhancements are some of the latest creations designed to enhance the security, quality, and efficiency of the radios. 36.1 ASTRO 25 Enhanced Data ASTRO 25 Enhanced Data is optimized to handle different message sizes and variable update rates from different applications of the radio. To improve data channel efficiency and enable denser network traffic, add Enhanced Data to the Integrated Data system with a software installation. 36.2 Dynamic System Resilience Dynamic System Resilience (DSR) ensures that the radio system is seamlessly switched to a backup master site dynamically during a system failure. DSR also provides indications such as failure detection, fault recovery, and redundancy within the system. DSR also supports mechanisms related to the Integrated Voice and Data (IV&D), or data centric. 36.3 Encrypted Integrated Data Encrypted Integrated Data (EID) provides security encryption and authentication of Integrated Voice and Data (IV&D) bearer service. This bridges the communication between the radio and the Customer Enterprise Network. 36.4 SecureNet SecureNet allows you to perform secured communications on an Analog or Motorola Data Communication (MDC) channel. 36.5 P25 Digital Vehicular Repeater System Motorola Solutions offers an MSI Certified APX compatible, third party, P25 Digital Vehicular Repeater System (DVRS). This provides low-cost portable radio coverage in areas where only mobile radio coverage is available. NOTE: Portable subscriber units enabled in the system for Radio Authentication shall be able to authenticate regardless of whether they are communicating directly on the system or by using a DVRS. DVRS can also work with SmartConnect to use broadband coverage for the in-vehicle mobile. Portable radios communicate through the in-vehicle mobile to the system through the LTE, Satellite, or Wi-Fi connection. This extends the system coverage when you are away from the vehicle. 105 MN009203A01-AD Chapter 37 : Accessories Chapter 37 Accessories Not all accessories are FCC certified to operate with all radio models or band splits. See the radio price pages for a list of FCC certified accessories or contact your sales representative for accessory compatibility. Table 15: Antenna Part Number AN000421A01 Table 16: Audio (Push-To-Talk) Description Antenna, VHF Whip, 136174 MHz, 18 cm Description Remote Speaker Microphone, IMPRES XP for APX with Dual Mic Noise Suppression Remote Speaker Microphone, IMPRES XP for APX with Dual Mic Noise Suppression, 3.5 mm Threaded Jack Accessory Kit, Tactical GCAI PTT Interface Module Accessory Kit, Tactical Throat Microphone Microphone, Tactical Ear Headset, Behind-The-Ear Headset, Over-The-Head Headset, Headband with Nexus Headset, Neckband with Nexus Headset, Hardhat with Nexus Earpiece, 2-Wire Swivel Loud Audio with Eartip Adapter, GCAI-Mini PTT Nexus Earpiece, Loud Audio, 1-Wire Single Earbud with Removable Earhook Surveillance Kit, 1-Wire with Loud Audio Translucent Tube Surveillance Kit, 2-Wire with Loud Audio Translucent Tube Surveillance Kit, 3-Wire with Loud Audio Translucent Tube Remote Speaker Microphone, RM780 IMPRES Windporting, Large, IP68 Accessory Kit, XVE500 Remote Speaker Microphone, High Im-

pact, Green with Knob Accessory Kit, XVE500 Remote Speaker Microphone, Black with Knob Part Number NMN6271_ NMN6274_ PMLN6827_ PMLN6828_ PMLN6829_ PMLN8085_ PMLN8086_ PMLN8265_ PMLN8266_ PMLN8267_ PMLN8295_ PMLN8297_ PMLN8337_ PMLN8341_ PMLN8342_ PMLN8343_ PMMN4128_ PMMN4132_ PMMN4132_BLK 116 Part Number PMMN4135_ PMMN4136_ PMMN4137_ PMMN4137_BLK PMMN4140_ PMMN4141_ PMMN4142_ Table 17: Audio (Receive only) Part Number NNTN8294_ NNTN8295_ NNTN8296_ NTN2572_ PMLN7052_ PMLN7560_ PMLN7696_ PMLN8120_ Table 18: Audio (Wireless) Part Number NNTN8127_ PMMN4096_ Table 19: Battery Part Number PMNN4813_ PMNN4815_ Table 20: Cable Part Number CB001059A01 CB001062A01 MN009203A01-AD Chapter 37 : Accessories Description Accessory Kit, XVP850 Remote Speaker Microphone with Chan-

nel Knob Accessory Kit, XVP830 Remote Speaker Microphone without Channel Knob Accessory Kit, XVE500 Remote Speaker Microphone, High Im-

pact, Green without Channel Knob Accessory Kit, XVE500 Remote Speaker Microhpone, Black without Channel Knob Remote Speaker Microphone, RM760 IMPRES Windporting, Large, IP68 Remote Speaker Microphone, XVP750 Remote Speaker Microphone, XVP730 Description Earbud, Operations Critical, 1-Wire, 29 cm Cord, Black Earbud, Operations Critical, 1-Wire, 116 cm Cord, Black Covert Kit, Wireless Earpiece with 12 Cable, for use with Bluetooth Pod Surveillance Kit, Operations Critical Wireless, 1-Wire with Trans-

lucent Tube Earpiece, Receive Only with Translucent Tube Surveillance Kit, Neckloop and Discreet Earpiece Kit Earpiece, Receive Only, XL Clear Tube, 3.5 mm Jack Description Accessory Kit, Wireless, STD PR Remote Speaker Microphone, Wireless Bluetooth Accessory Description Battery, Lithium-Ion IMPRES 2 IP68 2850T, 2850 mAH Battery, Lithium-Ion IMPRES 2 DIV 1 IP68 3200T, 3200 mAH Description Cable, Assembly, GCAI Mini Keyloader Cable, Assembly, GCAI Mini Cloning 117 MN009203A01-AD Chapter 37 : Accessories Part Number PMKN4231_ PMKN4265_ Description Cable, Port Programming, Test, and Align, PSA Cable, Data Table 21: Carry Solutions Part Number Description 4200865599 PMLN5407_ PMLN5408_ PMLN5409_ PMLN8369_ PMLN8370_ PMLN8609_ Table 22: Charger Part Number PMPN4593_ PS000242A01 PMPN4594_ PMPN4819_ 25009297002 Waist Belt, Mount-Support, Black Swivel Belt Loop Replacement, 2.5 in Swivel Belt Loop Replacement, 2.75 in Swivel Belt Loop Replacement, 3.0 in Belt Clip, APX N30 or APX N50, 2.0 in. Belt Clip, APX N30 or APX N50, 2.5 in. Hard Leather Carry Case, Swivel Belt Loop for APX N30 or APX N50, 2.75 in. Description Desktop Charger, Multi-unit, IMPRES 2, 1 Display Base Only Power Supply Adaptor, Power Supply Brick 100240 VAC Uni-

versal 15 V/6 A L6 C6P Desktop Charger, Multi-unit, IMPRES 2, 1 Display Ext PS NA/LA/CA Desktop Charger, Single Unit, IMPRES 2, Base Only Power Supply, AC Adaptor, Wall Cube, Switch Mode, Low Noise, 18 W US/NA, NDAA PMPN4820_ Desktop Charger, Single Unit, IMPRES 2, Ext PS US Table 23: Miscellaneous Part Number PMHN4429_ PMLN8334_ TL000166A01 Description Dust Cover, GCAI Mini Cable Adapter, GCAI Mini to GCAI for APX Battery Adapter, Unpowered Eliminator, Service Tool and Serv-

ice Aid TL000173A01 Connector, RF 118

 

 

en-US RF Energy Exposure Training and Product Safety Information for Portable Two-Way Radios fr-CA Formation sur lexposition aux RF et information sur la scurit du produit pour radios bidirectionnelles portatives es-LA Capacitacin sobre la exposicin a energa de radiofrecuencia e informacin de proteccin del producto para radios de dos vas porttiles pt-BR Treinamento sobre a Exposio Energia de RF e Informaes de Segurana do Produto para Rdios Portteis Bidirecionais https://learning.motorolasolutions.com/User_Documentation Caution Before using this radio, read this booklet which contains important operating instructions. For information on product details, brochures, user manuals and approved accessories. Please refer to www.motorolasolutions.com. Compliance with RF Exposure Standards National and international regulations require manufacturers to comply with the RF energy exposure limits for portable two-way radios before they can be marketed. Your Motorola Solutions two-way radio is designed, manufactured, and tested to comply with all applicable national and international regulations for human exposure to radio frequency electromagnetic energy. When two-way radios are used as a consequence of employment, applicable regulations may require users to be fully aware of and able to control their exposure to meet occupational requirements. RF Energy Exposure Awareness and Control Information and Operational Instructions for Occupational Use Notice: This radio is intended for use in occupational/controlled conditions where users are aware of their exposure and can exercise control over their exposure to meet the requirements in national and international regulations. This radio device is not authorized for general population, consumer use. For more information on what RF energy exposure is, and how to control your exposure to ensure compliance with established RF exposure limits, consult the following websites:

https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en http://www.who.int/peh-emf/project/en/

http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf11467.html http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01904.html For additional user training information on exposure requirements, consult the following websites:

English https://www.motorolasolutions.com/en_us/about/company-overview/

corporate-responsibility/governance-and-policies/wireless-

communication-and-health-faqs.html http://learning.motorolasolutions.com/

RF Exposure Compliance and Control Guidelines To control your exposure, and ensure compliance with the relevant RF exposure limits, always adhere to the following guidelines:

Do not remove any of the RF Exposure Labels if present from this device or its related accessories. Attach these instructions to the device when you transfer it to other Do not use this device if the operational requirements described users. herein are not met. Operating Instructions Transmit no more than 50% of the time. To transmit (talk), press the Push-To-Talk (PTT) button. To receive calls, release the PTT button. Transmitting more than 50% of the time may cause RF exposure compliance requirements to be exceeded. Hold the radio in a vertical position in front of the face with the microphone (and other parts of the radio including the antenna) at least 1 in. (2.5 cm) away from the nose or lips. Antenna should be kept away from the eye. When worn on the body, always place the radio in a Motorola Solutions-approved clip, holder, holster, case, or body harness for this product. DO NOT hold the antenna when the radio is transmitting. DO NOT use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result. To ensure continued compliance with applicable RF exposure limits, use only Motorola Solutions approved, supplied or replacement antennas, batteries, and accessories. For a list of Motorola Solutions approved accessories please refer to your user manual or visit www.motorolasolutions.com 1 English Acoustic Safety Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the volume of the radio, the sooner your hearing will be affected. Hearing damage from loud noise is sometimes undetectable at first, and can have a cumulative effect. To protect your hearing:

Use the lowest volume necessary to do your job. Turn up the volume only if you are in noisy surroundings. Turn down the volume before adding headset or earpiece. Limit the amount of time you use headsets or earpieces at high volume. When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear. Medical Devices If you use a personal medical device, such as a pacemaker or hearing aid, consult the manufacturer of your device to determine if it is adequately shielded from RF energy. Your physician may be able to assist you in obtaining this information. Holsters Incorporating Magnets Some Motorola Solutions holsters incorporate strong, neodymium magnets. If you use a personal medical device, such as a pacemaker or hearing aid, consult the manufacturer of your device to determine if it can be used in close proximity to magnets. Your physician may be able to assist you in obtaining this information. Also be aware that magnets can damage other products, including cell phones, computers, hard drives, and other electronic devices, as well as credit cards and magnetic media. Keep the holster away from any mechanical device that could be affected by a magnetic field. Consult the manufacturer of your product to determine if your device or product can be used in close proximity to magnets. Notice to Users (FCC) This device complies with Part 15 of the FCC rules per the following conditions:

This device may not cause harmful interference. 2 The device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this device, not expressly approved by Motorola Solutions, could void the authority of the user to operate this equipment. Operational Warnings The following explains the operational warnings:

For Vehicle With Air Bags Potentially Explosive Atmospheres Warning:

Refer to vehicle manufacturer's manual prior to installation of electronic equipment to avoid interference with air bag wiring. DO NOT place a portable radio in the area over an air bag or in the air bag deployment area. Air bags inflate with great force. If a portable radio is placed in the air bag deployment area and the air bag inflates, the radio may be propelled with great force and cause serious injury to occupants of the vehicle. Warning:

Do not carry a radio that is not certified for Hazardous Locations into a potentially explosive atmosphere. It could result in a serious injury or death. You should only use a radio certified for hazardous locations in potentially explosive atmospheres. Explosive atmospheres refer to hazard classified locations that may contain hazardous gas, vapors, dusts, such as fueling areas below decks on boats, fuel or chemical transferor storage facilities, and areas where the air contains chemicals or particles such as grain, dust or metal powders. Areas with potentially explosive atmospheres are often, but not always, posted. DO NOT remove, install, or charge batteries in such areas, or remove or install antennas. Sparks in a potentially explosive atmosphere can cause an explosion or fire resulting in bodily injury or even death. Blasting Caps and Blasting Areas Warning: To avoid possible interference with blasting operations, turn off your radio when you are near electrical blasting caps, in a blasting area, or in areas posted: Turn off two-way radio. Obey all signs and instructions. Batteries Caution: Use only Motorola Solutions approved batteries. Risk of explosion if the battery is replaced by an incorrect type. Charge your battery using the approved Motorola Solutions charger. Connect the charger/power supply to a nearby and easily accessible Use the battery in accordance with its water and/or dust Ingress power outlet. Protection (IP) rating. Do not discard your battery into a fire. Do not replace the battery in any area labeled "Hazardous Atmosphere". Do not disassemble, crush, puncture, shred, or otherwise attempt to change the form of your battery. Do not dry a wet or damp battery with an appliance or heat source, such as a hair dryer or microwave oven. Do not allow conductive material such as jewelry, keys, or beaded chains to touch exposed battery terminals. Do not dispose of batteries with household waste. Repair Warning:

Repairs to a Motorola Solutions intrinsically safe radio product certified by, for example, FM, UL, CSA, CENELEC, should only be done at a location that has been audited under the certifying body's repair and service standard. Contact Motorola Solutions for assistance regarding repairs and service of Motorola Solutions intrinsically safe equipment. A repair constitutes something done internally to the unit that would bring it back to its original condition. English Items not considered as repairs are those in which an action is performed on a unit which does not require the outer casing of the unit to be opened in a manner that exposes the internal electrical circuits of the unit. Do Not Substitute Options or Accessories The Motorola Solutions communications equipment certified as intrinsically safe by the approving agency (FM, UL, CSA, CENELEC) is tested as a complete system which consists of the listed agency Approved portable, Approved battery, and Approved accessories or options, or both. This Approved portable and battery combination must be strictly observed. There must be no substitution of items, even if the substitute has been previously Approved with a different Motorola Solutions communications equipment unit. Approved configurations are listed by the Approving Agency (FM, UL, CSA, CENELEC). The Intrinsically Safe Approval Label affixed to radio refers to the intrinsically safe classification of that radio product, and the approved batteries that can be used with that system. The manual PN referenced on the Intrinsically Safe Approval Label identifies the approved Accessories and or options that can be used with that portable radio unit. Using a non-Motorola Solutions-intrinsically safe battery and/or accessory with the Motorola Solutions approved radio unit will void the intrinsically safe approval of that radio unit. European Union (EU) Waste of Electrical and Electronic Equipment (WEEE) Directive The European Union's WEEE directive requires that products sold into EU countries must have the crossed out trash bin label on the product

(or the package in some cases). As defined by the WEEE directive, this cross-out trash bin label means that customers and end-users in EU countries should not dispose of electronic and electrical equipment or accessories in household waste. Customers or end-users in EU countries should contact their local equipment supplier representative or service centre for information about the waste collection system in their country. 3 For Brazil, information for disposal and recycling of electronic waste, batteries, and packaging, please call: 0800168272. English 4 Mise en garde Avant d'utiliser cette radio, lisez cette brochure qui contient d'importantes consignes d'utilisation. Pour obtenir plus dinformation sur les dtails du produit, les brochures, les manuels et les accessoires approuvs, Veuillez vous reporter www.motorolasolutions.com. Conformit aux normes sur l'exposition aux radiofrquences Les rglementations nationales et internationales noncent que les fabricants doivent sassurer que leurs produits sont conformes aux limites dexposition l'nergie RF avant de les commercialiser. Cette radio bidirectionnelle Motorola Solutions a t conue, fabrique et teste afin de garantir sa conformit aux normes nationales et internationales lies l'exposition des tres humains l'nergie lectromagntique de radiofrquence. Lorsque les radios bidirectionnelles sont utilises des fins professionnelles, la rglementation en vigueur exige que les utilisateurs soient pleinement conscients des effets de l'exposition et qu'ils soient capables de contrler le niveau d'exposition auquel ils se soumettent afin de rpondre aux exigences de leur profession. Information de sensibilisation et de gestion de l'exposition l'nergie RF, et consignes pour l'utilisation professionnelle Avis: Cette radio a t conue pour un usage professionnel dans un environnement contrl, o les utilisateurs sont pleinement conscients de l'exposition l'nergie RF laquelle ils sont soumis et peuvent exercer un contrle sur cette exposition afin de respecter les limites tablies par les rglements nationaux et internationaux. Ce dispositif radio n'est pas autoris pour l'utilisation grand public par des consommateurs ordinaires. Franais (Canada) https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en http://www.who.int/peh-emf/project/en/

http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf11467.html http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01904.html Pour plus de renseignements sur la formation des utilisateurs relativement aux limites d'exposition, consultez les sites suivants :

https://www.motorolasolutions.com/en_us/about/company-overview/

corporate-responsibility/governance-and-policies/wireless-

communication-and-health-faqs.html http://learning.motorolasolutions.com/

Directives de conformit et de contrle de l'exposition aux RF Pour contrler votre exposition et garantir le respect des limites d'exposition applicables, observez toujours les consignes suivantes. Ne pas retirer les tiquettes relatives l'exposition aux RF qui sont apposes sur cet appareil ou sur ses accessoires. Joignez ces directives l'appareil lorsque vous le transfrez d'autres utilisateurs. N'utilisez pas cet appareil si les conditions de fonctionnement dcrites aux prsentes ne sont pas runies. Consignes dutilisation Ne pas mettre plus de 50 % du temps. Pour transmettre (parler), appuyez sur le bouton (PTT). Pour recevoir les appels, relchez le bouton PTT. Le fait de transmettre plus de 50 % du temps peut entraner le dpassement de la limite dexposition normalise au rayonnement RF. Tenez la radio la verticale devant le visage, en maintenant une distance dau moins 2,5 centimtres (1 pouce) entre le micro (et les autres parties de la radio, y compris lantenne) et le nez ou les lvres. Lantenne doit tre maintenue loin des yeux. Visitez les sites Web suivants pour obtenir plus de renseignements sur ce qu'est l'nergie RF et sur les moyens de contrle prendre afin de respecter les limites tablies en matire d'exposition aux radiofrquences :

Lorsque vous portez la radio sur vous, fixez-la toujours avec une pince ou une attache de ceinture et placez-la dans un tui ou un harnais approuv par Motorola Solutions pour l'utilisation avec ce produit. 1 Franais (Canada) NE TENEZ PAS lantenne entre vos doigts pendant que la radio met. N'UTILISEZ PAS une radio portative, quelle quelle soit, dont lantenne est endommage. Si une antenne endommage entre en contact avec votre peau, il peut en rsulter une brlure lgre. Pour assurer la conformit continue avec les limites d'exposition aux RF applicables, utilisez uniquement les antennes, les batteries et les accessoires de remplacement ou fournis et approuvs par Motorola Solutions. Pour obtenir une liste des accessoires approuvs par Motorola Solutions, veuillez consulter votre manuel ou visitez le site www.motorolasolutions.com Protection de l'oue Une exposition des bruits forts en provenance de n'importe quelle source pendant de longues priodes pourrait affecter votre audition de manire temporaire ou permanente. Plus le volume de la radio est lev, plus le dommage pour l'oue survient rapidement. Des dommages auditifs dus l'exposition des bruits forts peuvent ne pas tre dcels immdiatement, mais leurs effets sont parfois cumulatifs. Pour protger votre audition :

Rglez le volume le plus bas possible pour effectuer votre travail. Montez le volume seulement si vous vous trouvez dans un environnement bruyant. Baissez le volume avant dajouter un casque ou une oreillette. Limitez la priode de temps dutilisation de casques ou dcouteurs volume lev. Lorsque vous utilisez la radio sans casque ni couteur, ne placez pas le haut-parleur directement sur votre oreille. Appareils mdicaux Si vous utilisez un dispositif mdical personnel, comme un stimulateur cardiaque ou une prothse auditive, consultez le fabricant de votre appareil pour dterminer s'il est convenablement protg contre les RF. Votre mdecin peut vous aider obtenir ces renseignements. tuis incorporant des aimants Certains tuis Motorola Solutions intgrent des aimants puissants en nodyme. Si vous utilisez un dispositif mdical personnel, comme un 2 stimulateur cardiaque ou une prothse auditive, consultez le fabricant de votre appareil pour dterminer s'il peut tre utilis proximit d'aimants. Votre mdecin peut vous aider obtenir ces renseignements. Notez galement que les aimants peuvent endommager d'autres produits, notamment les tlphones cellulaires, les ordinateurs, les disques durs et autres appareils lectroniques, ainsi que les cartes de crdit et les supports magntiques. Gardez l'tui loin de tout dispositif mcanique qui pourrait tre affect par un champ magntique. Consultez le fabricant de votre produit pour savoir si votre appareil ou votre produit peut tre utilis proximit d'aimants. Avis aux utilisateurs (FCC) Cet appareil est conforme la partie 15 des rglements de la FCC daprs les conditions suivantes :

Cet appareil ne doit pas causer dinterfrence nuisible. L'appareil doit accepter toute interfrence reue, y compris les interfrences pouvant entraner un fonctionnement indsirable. Toute modification effectue cet appareil sans lautorisation explicite de Motorola Solutions peut annuler lautorisation dutiliser cet appareil. Avertissements de fonctionnement Le tableau suivant explique les avertissements de fonctionnement :

Pour vhicules quips de coussins gonflables Avertissement:

Consultez le manuel du fabricant du vhicule avant d'installer un appareil lectronique afin d'viter toute interfrence avec le cblage des coussins gonflables. NE PLACEZ PAS de radio portative dans la zone situe au-

dessus d'un coussin gonflable ou dans la zone de dploiement de ce dernier. Un coussin gonflable de scurit se dploie avec beaucoup de force. Si une radio portative se trouve dans la zone de dploiement du coussin, lorsque celui-ci se gonfle, la radio peut tre propulse avec une force considrable et risque alors d'occasionner de graves lsions corporelles aux passagers du vhicule. Atmosphres potentiellement explosives Avertissement:

Ne transportez pas une radio qui n'est pas certifie pour les emplacements dangereux dans une atmosphre potentiellement explosive. Cela pourrait entraner des blessures graves ou la mort. Vous ne devez utiliser qu'une radio certifie pour les endroits dangereux dans les atmosphres potentiellement explosives. On retrouve des atmosphres explosives dans les lieux classs comme tant dangereux en raison de la prsence de gaz, de vapeurs et de poussires reprsentant un danger, par exemple, les zones d'avitaillement en carburant dans des cales de bateau, les installations de transfert et de stockage de carburant ou de produits chimiques, et les zones dans lesquelles l'air est charg en produits chimiques ou en particules telles que de la poudre de crales, de la poussire ou de la poudre mtallique. Les zones atmosphres potentiellement explosives affichent gnralement des panneaux de mise en garde, mais ce n'est pas toujours le cas. VITEZ d'enlever, d'installer ou de charger les batteries, ou d'enlever ou d'installer des antennes dans de tels lieux. Les tincelles dans des atmosphres potentiellement explosives peuvent provoquer une explosion ou un incendie et entraner des lsions corporelles, voire la mort. Zone de dynamitage et dtonateurs Avertissement: teignez la radio lorsque vous vous trouvez proximit de dtonateurs lectriques ou dans une zone de dynamitage afin dviter de dclencher une explosion, ou lorsque vous vous trouvez dans un endroit o il est indiqu :

teindre les radios bidirectionnelles . Respectez tous les panneaux et toutes les consignes. Batteries Solutions. Mise en garde: Utilisez uniquement les batteries agres par Motorola Solutions. La batterie risque d'exploser si elle n'est pas correctement remplace. Chargez votre batterie l'aide du chargeur approuv par Motorola Franais (Canada) Branchez le chargeur/bloc d'alimentation une prise murale proximit facilement accessible. Utilisez la batterie conformment son indice de protection (IP) contre l'eau et la poussire. Ne jetez pas votre batterie au feu. Ne remplacez pas la batterie dans un endroit qui porte la mention atmosphre dangereuse . Veillez ne pas dmonter, craser, percer, dcouper ou autrement modifier la forme de votre batterie. Ne faites pas scher une batterie mouille ou humide avec un appareil lectrique ou une source de chaleur, comme un schoir cheveux ou un four micro-ondes. Ne permettez pas des matriaux conducteurs, comme des bijoux, des cls ou des mailles de chane dentrer en contact avec les bornes de la batterie. Ne jetez pas les batteries avec les ordures domestiques. Rparations Avertissement:

La rparation d'une radio de scurit intrinsque de Motorola Solutions homologue, notamment, par FM, UL, CSA ou CENELEC, doit tre effectue uniquement un endroit ayant fait l'objet d'une vrification en vertu de la norme sur les rparations et l'entretien de l'organisme de certification. Contactez Motorola Solutions afin d'obtenir de l'assistance pour l'entretien et la rparation d'une unit Motorola Solutions scurit intrinsque. Le terme rparation dsigne tout travail effectu sur les composants internes de l'unit afin de la ramener son tat d'origine. Un travail qui ne ncessite pas l'ouverture du botier de l'unit afin d'en exposer les circuits lectriques internes ne constitue pas une rparation. vitez de substituer des options ou des accessoires. L'quipement de communications Motorola Solutions certifi de scurit intrinsque par l'entit d'homologation (FMRC, UL, CSA, CENELEC) est test en tant que systme complet, savoir : la radio portative, la batterie, les accessoires et les options, tous agrs par l'entit correspondante. L'intgrit de cette configuration forme d'une radio portative et d'une batterie agres doit tre strictement respecte. 3 Franais (Canada) Aucune substitution d'lment n'est permise, mme si l'lment de remplacement a pralablement t agr pour une autre unit de communication Motorola Solutions. Les configurations agres peuvent tre consultes dans la liste mise disposition par l'entit d'homologation (FMRC, UL, CSA, CENELEC). L'tiquette d'homologation de scurit intrinsque appose sur la radio identifie la classification de scurit intrinsque de cette radio ainsi que les batteries agres qui peuvent tre utilises avec ce systme. Le numro de rfrence du manuel mentionn sur l'tiquette d'homologation de scurit intrinsque identifie les accessoires et/ou les options agrs qui peuvent tre utiliss avec cette unit de radio portative. Le fait de ne pas utiliser une batterie ou un accessoire Motorola Solutions de scurit intrinsque avec l'unit de radio Motorola Solutions agre annule l'homologation de scurit intrinsque de cette unit de radio. Directive sur la mise au rebut des quipements lectriques et lectroniques de lUnion europenne (UE)

(WEEE) La directive WEEE de lUnion europenne exige que les produits (ou leur emballage, dans certains cas) vendus dans les pays de lUE portent ltiquette de la poubelle barre. Comme le dfinit la directive WEEE, cette tiquette de poubelle barre signifie que les clients et les utilisateurs finaux dans les pays de lUE ne doivent pas jeter les quipements lectriques et lectroniques ou leurs accessoires dans les ordures domestiques. Les clients ou les utilisateurs finaux dans les pays de lUE doivent communiquer avec le reprsentant ou le centre de service de leur fournisseur dquipement pour obtenir des renseignements sur le systme de collecte des dchets de leur pays. Pour obtenir des renseignements sur l'limination et le recyclage des dchets lectroniques, des batteries et des emballages pour le Brsil, veuillez appeler : 0800168272. 4 Precaucin Antes de usar este radio, lea el folleto que contiene instrucciones de funcionamiento importantes. Para obtener informacin sobre los detalles del producto, folletos, manuales de usuario y accesorios aprobados. consulte www.motorolasolutions.com. Conformidad con las normas de exposicin a radiofrecuencia Las regulaciones nacionales e internacionales obligan a que los fabricantes cumplan con los lmites de exposicin a energa de radiofrecuencia para radios porttiles de dos vas antes de que se puedan comercializar. El radio de dos vas de Motorola Solutions est diseado, fabricado y probado para cumplir con todas las regulaciones nacionales e internacionales correspondientes en materia de exposicin humana a la energa electromagntica de radiofrecuencia. Cuando los radios de dos vas se usan para trabajar, las regulaciones correspondientes podran exigir que los usuarios conozcan y controlen su nivel de exposicin para cumplir con los requisitos de uso profesional. Conocimiento de la exposicin a energa de radiofrecuencia, informacin de control e instrucciones de funcionamiento para uso ocupacional Nota: Este radio est diseado para usarse en condiciones controladas o profesionales, donde los usuarios tengan pleno conocimiento de su exposicin y puedan controlarla con el fin de cumplir con los requisitos de las regulaciones nacionales e internacionales. Este dispositivo de radio no est autorizado para el uso particular de la poblacin en general. Para obtener ms informacin sobre el significado de la exposicin a energa de radiofrecuencia y cmo controlar la exposicin con el fin de asegurar el cumplimiento de los lmites de exposicin a radiofrecuencias establecidos, consulte los siguientes sitios web:

https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en Espaol (Latinoamrica) http://www.who.int/peh-emf/project/en/

http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf11467.html http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01904.html Para obtener informacin adicional de la capacitacin de los usuarios sobre los requisitos de exposicin, consulte los siguientes sitios web:

https://www.motorolasolutions.com/en_us/about/company-overview/

corporate-responsibility/governance-and-policies/wireless-

communication-and-health-faqs.html http://learning.motorolasolutions.com/

Cumplimiento de exposicin a radiofrecuencia y pautas de control Para controlar la exposicin y garantizar el cumplimiento de los lmites de exposicin a radiofrecuencias correspondientes, respete siempre las siguientes pautas:

No retire ninguna de las etiquetas de exposicin a radiofrecuencias, si las hubiere, de este dispositivo o sus accesorios respectivos. Adjunte estas instrucciones al dispositivo cuando se lo transfiera a otros usuarios. No utilice este dispositivo si no se cumple con los requisitos de funcionamiento descritos en este documento. Instrucciones de funcionamiento No transmita ms de un 50 % del tiempo. Para transmitir (hablar), presione el botn Push-to-Talk (PTT). Para recibir llamadas, suelte el botn PTT. Una transmisin superior al 50 % del tiempo de uso podra provocar que se superen los requisitos de cumplimiento de exposicin a radiofrecuencia. Sostenga el radio en posicin vertical frente a su rostro con el micrfono (y otras partes del radio, incluida la antena) al menos a 2,5 cm (1 pulg.) de distancia de la nariz o los labios. Mantenga la antena alejada de los ojos. Siempre que use el radio ajustado al cuerpo, pngalo en un clip, un soporte, un estuche, una funda o un arns para el cuerpo aprobado por Motorola Solutions para este producto. NO sujete la antena mientras el radio est realizando una transmisin. 1 Espaol (Latinoamrica) NO utilice radios porttiles que tengan la antena daada. Si una antena daada toca su piel, puede causar una pequea quemadura. Para garantizar el cumplimiento continuo de los lmites de exposicin a radiofrecuencia correspondientes, utilice solamente las antenas, las bateras y los accesorios de repuesto suministrados o aprobados por Motorola Solutions. telfonos celulares, computadoras, discos duros y otros dispositivos electrnicos, adems de las tarjetas de crdito y los medios magnticos. Mantenga la funda lejos de cualquier dispositivo mecnico que el campo magntico pueda afectar. Consulte con el fabricante del producto para determinar si el dispositivo o el producto se pueden utilizar cerca de imanes. Para obtener una lista de los accesorios aprobados por Motorola Solutions, consulte el manual del usuario o visite www.motorolasolutions.com. Seguridad acstica La exposicin a ruidos fuertes de cualquier fuente durante perodos prolongados podra afectar la audicin de manera temporal o permanente. Cuanto ms alto sea el volumen del radio, ms rpido se ver afectada la audicin. En ocasiones, el dao a la audicin provocado por ruidos fuertes es indetectable en un principio y puede tener efecto acumulativo. Para proteger la audicin:

Utilice el volumen ms bajo que necesite para hacer su trabajo. Aumente el volumen solo si se encuentra en un ambiente ruidoso. Reduzca el volumen antes de conectar los auriculares o el audfono. Limite el tiempo durante el cual usa los auriculares o los audfonos a volumen alto. Cuando use el radio sin audfonos o auriculares, no coloque el altavoz del radio directamente en la oreja. Aparatos mdicos Si utiliza un dispositivo mdico, como un marcapasos o una prtesis auditiva, consulte al fabricante del dispositivo para determinar si est adecuadamente protegido contra las energas de radiofrecuencia. Su mdico podra ayudarlo a obtener esta informacin. Fundas con imanes Algunas fundas de Motorola Solutions incluyen imanes de neodimio resistentes. Si utiliza un dispositivo mdico personal, como un marcapasos o una prtesis auditiva, consulte con el fabricante del dispositivo para determinar si se puede utilizar cerca de imanes. Su mdico podra ayudarlo a obtener esta informacin. Adems, tenga presente que los imanes pueden daar otros productos, incluidos Nota para los usuarios (FCC) Este dispositivo cumple con la Parte 15 de las normas de la FCC segn las siguientes condiciones:

Este dispositivo no puede provocar interferencia nociva. El dispositivo debe aceptar toda interferencia recibida, incluida aquella interferencia que pudiera causar un funcionamiento no deseado. Los cambios o las modificaciones que se realicen en este dispositivo, no aprobados expresamente por Motorola Solutions, podran anular el permiso del usuario de operar este equipo. Advertencias de funcionamiento A continuacin, se explican las advertencias de funcionamiento:

Para vehculos con bolsas de aire Advertencia:

Consulte el manual del fabricante del vehculo antes de instalar equipos electrnicos, a fin de evitar la interferencia en el cableado de las bolsas de aire. NO coloque el radio porttil sobre una bolsa de aire ni en el rea de despliegue de la bolsa. Las bolsas de aire se inflan con mucha fuerza. Si se pone un radio porttil en el rea de despliegue de la bolsa de aire y esta se infla, es posible que el radio salga disparado con gran fuerza y cause lesiones graves a los ocupantes del vehculo. Atmsferas potencialmente explosivas Advertencia:

No lleve un radio que no est certificado para lugares peligrosos a una atmsfera potencialmente explosiva. Puede provocar lesiones graves o la muerte. En atmsferas potencialmente explosivas, solo debe utilizar un radio certificado para lugares peligrosos. 2 Espaol (Latinoamrica) El trmino atmsferas explosivas se refiere a lugares No permita que materiales conductores como joyas, llaves o cadenas clasificados como peligrosos en los que podra haber gases, vapores o polvos peligrosos, como reas con combustibles bajo las cubiertas de los botes o instalaciones de almacenamiento o transferencia de qumicos, y reas en que el aire contenga productos qumicos o partculas, como material granulado, polvo o polvo metlico. A menudo, en las reas con atmsferas potencialmente explosivas hay seales de precaucin, aunque no siempre es as. NO retire, instale ni cargue bateras, ni tampoco retire o instale antenas en dichas reas. Las chispas en ambientes potencialmente explosivos pueden desencadenar una explosin o un incendio, y ocasionar lesiones o incluso la muerte. reas de voladuras y explosivos Advertencia: Para evitar posibles interferencias en operaciones de voladuras, apague el radio cuando se encuentre cerca de zonas de voladuras elctricas, en un rea de explosivos o en reas donde se encuentre el siguiente aviso: Apague el radio de dos vas. Obedezca todas las seales e instrucciones. Bateras Precaucin: Utilice nicamente bateras aprobadas por Motorola Solutions. Existe un riesgo de explosin si sustituye la batera por otra de una clase incorrecta. Cargue la batera con cargadores aprobados por Motorola Solutions. Conecte el cargador/la fuente de alimentacin a una toma de corriente cercana y de fcil acceso. Utilice la batera de acuerdo con su clasificacin de proteccin de ingreso (IP) contra polvo y agua. No arroje la batera al fuego. No cambie la batera en un rea designada como Atmsfera peligrosa. No desarme, rompa, perfore, triture ni intente cambiar de ningn otro modo la forma de la batera. No intente secar una batera mojada o hmeda con un electrodomstico o una fuente de calor externa, como un secador de pelo o un horno microondas. hagan contacto con los terminales expuestos de la batera. No bote las bateras en la basura domstica. Reparaciones Advertencia:

Las reparaciones de productos de un radio Motorola Solutions intrnsecamente seguro certificado, por ejemplo, FM, UL, CSA, CENELEC, deben realizarse solo en una ubicacin que haya sido auditada segn el estndar de reparacin y servicio de la entidad certificante. Comunquese con Motorola Solutions para solicitar asistencia relacionada con reparaciones y tareas de servicio de los equipos Motorola Solutions intrnsecamente seguros. Una reparacin consta de algo hecho en el interior de la unidad que debe devolverla a su estado original. Las instancias que no se consideran reparaciones son las que incluyen una accin realizada en una unidad que no requiere que la cubierta externa se abra de manera tal que queden expuestos los circuitos elctricos de la unidad. No sustituya los elementos opcionales ni los accesorios Los equipos de comunicaciones de Motorola Solutions que cuentan con un certificado que indica que son intrnsecamente seguros, emitido por una agencia de aprobacin (FM, UL, CSA, CENELEC), se prueban como sistemas completos que incluyen: el dispositivo porttil aprobado, la batera aprobada y los accesorios o los elementos opcionales aprobados, o ambos. Debe respetar de manera estricta esta combinacin de dispositivo porttil y batera aprobada. No se deben sustituir los elementos, aun si la pieza de sustitucin se prob anteriormente para otro equipo de comunicaciones Motorola Solutions. Las configuraciones aprobadas son detalladas por la agencia de aprobacin (FM, UL, CSA, CENELEC). La etiqueta de aprobacin como intrnsecamente seguro adherida al radio indica la clasificacin de intrnsecamente seguro de ese radio e indica las bateras aprobadas que pueden usarse con ese sistema. La etiqueta de aprobacin de intrnsecamente seguro adherida al radio hace referencia a un nmero de pieza del manual que indica los 3 Espaol (Latinoamrica) accesorios o los elementos opcionales que se pueden usar con la unidad de radio porttil. El uso de una batera o un accesorio aprobado como intrnsecamente seguro que no sea de Motorola Solutions con el radio Motorola Solutions aprobado anular la aprobacin de intrnsecamente seguro de esa unidad de radio. Directiva de Residuos de Aparatos Elctricos y Electrnicos (RAEE) de la Unin Europea (UE) La directiva de RAEE de la Unin Europea requiere que los productos que se venden en los pases de la UE tengan la etiqueta de un bote de residuos tachado sobre el producto (o en el paquete en algunos casos). Como se define en la Directiva de RAEE, esta etiqueta con un bote de basura tachado indica que los clientes y los usuarios finales en los pases de la UE no deben deshacerse de los equipos o accesorios elctricos y electrnicos con la basura domstica. Los clientes o los usuarios finales en los pases de la UE deben comunicarse con su representante distribuidor de equipos o el centro de servicio locales para obtener informacin sobre el sistema de recoleccin de residuos de su pas. Para Brasil, informacin de eliminacin y reciclaje de desechos electrnicos, bateras y embalajes, llame al: 0800168272. 4 Ateno Antes de usar o rdio, leia este folheto, que contm importantes instrues de operao. Para obter informaes sobre detalhes do produto, folhetos, manuais do usurio e acessrios aprovados. Consulte www.motorolasolutions.com. Conformidade com os Padres de Exposio RF Os regulamentos nacionais e internacionais exigem que os fabricantes estejam em conformidade com os limites de exposio energia de RF para rdios portteis bidirecionais antes de serem comercializados. O rdio bidirecional da Motorola Solutions foi projetado, fabricado e testado para estar em conformidade com todos os regulamentos nacionais e internacionais para exposio de seres humanos energia eletromagntica de radiofrequncia. Ao usar rdios bidirecionais por motivos de trabalho, os regulamentos aplicveis podem exigir que os usurios estejam totalmente conscientes e aptos a controlar sua exposio de modo a atender s exigncias ocupacionais. Informaes sobre Conscientizao e Controle de Exposio Energia de RF e Instrues Operacionais para o Uso Ocupacional Comunicado: Este rdio destina-se ao uso em condies ocupacionais/controladas, em que os usurios estejam cientes de sua exposio e possam exercer controle sobre ela, para atender aos requisitos nos regulamentos nacionais e internacionais. O uso do dispositivo de rdio pela populao em geral no autorizado. Para obter mais informaes sobre a exposio energia de RF e como controlar a exposio para garantir a conformidade com os limites de exposio RF estabelecidos, acesse os seguintes sites:

https://www.fcc.gov/

https://www.osha.gov/

https://osha.europa.eu/en http://www.who.int/peh-emf/project/en/

http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf11467.html http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01904.html Portugus (Brasil) Para informaes adicionais de treinamento sobre os requisitos de exposio, acesse os seguintes sites:

https://www.motorolasolutions.com/en_us/about/company-overview/

corporate-responsibility/governance-and-policies/wireless-

communication-and-health-faqs.html http://learning.motorolasolutions.com/

Diretrizes de Conformidade e Controle de Exposio RF Para controlar a exposio e garantir a conformidade com os limites de exposio RF em questo, siga sempre as diretrizes a seguir:

No remova as Etiquetas de Exposio RF, se houverem, do dispositivo ou acessrios relacionados. Anexe essas instrues ao dispositivo quando o transferir a outros No use este dispositivo se os requisitos operacionais descritos aqui usurios. no forem atendidos. Instrues Operacionais Transmita, no mximo, 50% do tempo. Para transmitir (falar), pressione o boto PTT (Push-To-Talk). Para receber chamadas, solte o boto PTT (Push-To-Talk, apertar para falar). Transmitir mais de 50% do tempo pode fazer que os requisitos de conformidade de exposio RF sejam excedidos. Segure o rdio em posio vertical em frente ao rosto com o microfone (e outras partes do rdio incluindo a antena) a pelo menos 2,5 cm (1 polegada) de distncia do nariz ou dos lbios. A antena deve ficar longe dos olhos. Ao usar o rdio junto ao corpo, sempre o coloque em um prendedor, suporte, suporte para cinto ou estojo para este produto aprovado pela Motorola Solutions. NO segure a antena enquanto o rdio estiver transmitindo. NO utilize um rdio porttil com antena danificada. Se a antena danificada entrar em contato com sua pele, poder causar uma queimadura leve. Para garantir constantemente a conformidade com os limites aplicveis de exposio RF, use apenas antenas, baterias e acessrios de reposio aprovados ou fornecidos pela Motorola Solutions. 1 Portugus (Brasil) Para obter uma lista dos acessrios aprovados pela Motorola Solutions, consulte o manual do usurio ou acesse www.motorolasolutions.com Segurana Acstica A exposio a rudos muito altos de qualquer origem por longos perodos pode prejudicar sua audio temporria ou permanentemente. Quanto maior for o volume do rdio, mais cedo sua audio ser prejudicada. s vezes, os danos auditivos causados por rudos fortes no so detectados em sua fase inicial, e podem ter efeito cumulativo. Para proteger sua audio:

Use o volume mais baixo necessrio para a execuo da sua tarefa. Aumente o volume somente se estiver em ambientes barulhentos. Reduza o volume antes de conectar o headset ou o fone de ouvido. Limite o tempo de uso dos fones auriculares ou fones de ouvido com volume alto. Ao utilizar o rdio sem monofones ou fones de ouvido, no coloque o alto-falante do rdio diretamente em contato com seus ouvidos. Equipamentos Mdicos Se voc usa um dispositivo mdico pessoal, como um marca-passo ou aparelho auditivo, consulte o fabricante do dispositivo para determinar se est adequadamente protegido contra energia de RF. Seu mdico pode ajud-lo a obter essas informaes. Coldre magntico Alguns coldres da Motorola Solutions contm ms fortes e de neodmio. Se voc usa um dispositivo mdico pessoal, como um marca-passo ou aparelho auditivo, consulte o fabricante do dispositivo para determinar se ele pode ser usado prximo de ms. Seu mdico pode ajud-lo a obter essas informaes. Tambm esteja ciente de que os ms podem danificar outros produtos, incluindo telefones celulares, computadores, discos rgidos e outros dispositivos eletrnicos, bem como cartes de crdito e de mdia magntica. Mantenha o coldre longe de qualquer dispositivo mecnico que pode ser afetado por um campo magntico. Consulte o fabricante do seu produto para determinar se o seu dispositivo ou produto pode ser usado prximo de ms. 2 Aviso aos Usurios (FCC) Este dispositivo est em conformidade com a parte 15 das normas da FCC, de acordo com as seguintes condies:

Este dispositivo no pode causar interferncias prejudiciais sade. O dispositivo deve aceitar qualquer interferncia recebida, inclusive as que possam causar operao indesejvel do dispositivo. Alteraes ou modificaes feitas neste dispositivo, que no sejam expressamente aprovadas pela Motorola Solutions, podero anular o direito do usurio de operar o equipamento. Avisos Operacionais A seguir so explicados os avisos operacionais:

Para Veculos Equipados com Air Bags Ambientes Potencialmente Explosivos Aviso:

Consulte o manual do fabricante do veculo antes de instalar equipamentos eletrnicos para evitar interferncia com o funcionamento do air bag. NO coloque um rdio porttil na rea sobre um air bag ou na rea de liberao do air bag. Os air bags inflam com muita fora. Se um rdio porttil estiver colocado na rea de liberao do air bag e o air bag inflar, o rdio poder ser impelido com grande fora e causar srios ferimentos aos ocupantes do veculo. Aviso:

No transporte um rdio que no seja certificado para locais de risco em ambientes potencialmente explosivos. Isso pode resultar em ferimentos graves ou morte. Voc deve usar apenas um rdio certificado para locais de risco em ambientes potencialmente explosivos. Ambientes potencialmente explosivos referem-se a locais classificados como de risco que podem conter gases, vapores ou ps nocivos, como reas de abastecimento embaixo do convs principal em barcos, instalaes de armazenamento ou transferncia de produtos qumicos ou combustvel e reas onde o ar contm partculas ou elementos qumicos, como fibras, poeira ou ps metlicos. As reas com ambientes potencialmente explosivos so frequentes, mas nem sempre h avisos sobre isso. NO remova, instale ou carregue baterias nessas reas, nem remova ou instale antenas. Fascas em um ambiente potencialmente explosivo podem causar uma exploso ou incndio que pode resultar em ferimentos e, at mesmo, morte. Reparo reas e Equipamentos para Detonao Aviso: Para evitar possveis interferncias em operaes de detonao, desligue o rdio quando estiver prximo a detonadores eltricos, reas de detonao ou reas onde haja avisos tais como: Desligue rdios bidirecionais. Obedea a todas as sinalizaes e instrues. Baterias Ateno: Use somente baterias aprovadas pela Motorola Solutions. Se a bateria for substituda por uma de tipo incorreto, haver risco de exploso. Sempre carregue a bateria usando o carregador aprovado pela Motorola Solutions. e de fcil acesso. Conecte o carregador/a fonte de alimentao a uma tomada prxima Use a bateria de acordo com sua classificao de Proteo contra entrada (IP) de p e gua. No descarte a bateria no fogo. No troque a bateria em lugares identificados como "Atmosferas Potencialmente Perigosas". No desmonte, comprima, perfure, fragmente ou tente, de outras maneiras, alterar a forma da bateria. No seque baterias molhadas nem midas usando aparelhos ou fontes de calor, como secadores de cabelo ou fornos de micro-ondas. No permita que materiais condutores como joias, chaves ou correntes toquem os terminais expostos da bateria. No descarte baterias no lixo domstico. Portugus (Brasil) Aviso:

Reparos em rdios intrinsecamente seguros da Motorola Solutions certificados, por exemplo, por FM, UL, CSA, CENELEC, devem ser feitos apenas em um local que passou por auditoria de acordo com as normas de reparo e manuteno dos rgos certificadores. Entre em contato com a Motorola Solutions para obter assistncia sobre reparos e servios em equipamentos Motorola Solutions intrinsecamente seguros. Um reparo constitui algo sendo feito internamente na unidade que a retornar as suas condies originais. Os itens que no so considerados como reparos so os em que a ao realizada em uma unidade que no precisa que a parte externa seja aberta para expor os circuitos eltricos internos da unidade. No Substitua Opes ou Acessrios O equipamento de comunicao Motorola Solutions certificado como intrinsecamente seguro pelos rgos de aprovao (FM, UL, CSA, CENELEC), testado como um sistema completo que consiste do porttil aprovado, bateria aprovada e acessrios e/ou opes aprovados pelo rgo listado. Essa combinao de porttil e bateria aprovada deve ser estritamente observada. No pode haver substituio de itens, mesmo se o substituto tiver sido aprovado previamente com um equipamento de comunicaes Motorola Solutions diferente. As configuraes aprovadas so listadas pelo rgo Aprovador (FM, UL, CSA, CENELEC). A Etiqueta de Aprovao de Intrinsecamente Seguro afixada ao rdio refere-se classificao de intrinsecamente seguro do rdio e da bateria aprovada que pode ser usada com o sistema. O PN manual referenciado na Etiqueta de Aprovao de Intrinsecamente Seguro identifica os acessrios ou opes aprovados que podem ser usados com a unidade de rdio porttil. O uso de uma bateria e/ou acessrio intrinsecamente seguro no Motorola Solutions com a unidade de rdio aprovada pela Motorola Solutions invalidar a aprovao de segurana intrnseca da unidade de rdio. 3 Portugus (Brasil) Diretiva de Resduos de Equipamentos Eltricos e Eletrnicos (WEEE) para a Unio Europeia (UE) A Diretiva de WEEE da Unio Europeia exige que os produtos vendidos nos pases da UE tenham a etiqueta de lixeira riscada no produto (ou no pacote, em alguns casos). Conforme definido pela diretiva WEEE, essa etiqueta de lixeira cruzada indica que os clientes e os usurios nos pases da UE no devem descartar equipamentos ou acessrios eltricos ou eletrnicos em lixo domstico. Os clientes ou os usurios nos pases da UE devem entrar em contato com o representante local do fornecedor do equipamento ou com a central de servios para obter informaes sobre o sistema de coleta de lixo em seu pas. Para informaes sobre descarte e reciclagem de resduos eletrnicos, baterias e embalagens, por favor, ligue: 0800168272. 4 Notes Cover.fm Page 1 Wednesday, April 24, 2019 12:39 PM MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. 2004 and 2020 Motorola Solutions, Inc. All rights reserved.

*NNTN7223R*

NNTN7223R Printed in

*6881095C98*

6881095C98-LH

 

 

 

 

 

 

 

 

 

 

Applicant: Motorola Solutions Inc FCC ID: AZ489FT7162 / IC: 109U-89FT7162 EXHIBIT 1 IDENTIFICATION LABEL

(Pursuant to FCC Part 2.1033(c)(11), 2.1033(b)(7) and RSP 100 Annex C and Sec 3) LOCATION See the Attached Photograph or Sketch ____ ____ Bottom of the device ____ Front of the device X Back of the device ____ Back of the device under Belt Clip ____ ____ Electronic labeling: In the user manual (Section: XX) In the Battery Compartment TYPE X MARKINGS (TEXT) The label is a polyester film with a pressure sensitive adhesive backing. The adhesive is a permanent type acrylic with the minimum peel strength of 8.89 N/mm. The label is an electronic print accessible in the device. X See the Attached Photograph and Exhibit 3 for the actual location of the FCC/IC label on the device. X Label Attached Below. See Attached Drawing. EXHIBIT 1 Revision 2 (12 Jan 2023) SHEET 1 OF 5 Applicant: Motorola Solutions Inc FCC ID: AZ489FT7162 / IC: 109U-89FT7162 Figure 1: FCC/IC Label for APX N50 EXHIBIT 1 Revision 2 (12 Jan 2023) SHEET 2 OF 5 Applicant: Motorola Solutions Inc FCC ID: AZ489FT7162 / IC: 109U-89FT7162 Figure 2: FCC/IC Label for APX N30 EXHIBIT 1 Revision 2 (12 Jan 2023) SHEET 3 OF 5 Applicant: Motorola Solutions Inc FCC ID: AZ489FT7162 / IC: 109U-89FT7162 Figure 3: FCC/IC Label for APX N50 Hazloc EXHIBIT 1 Revision 2 (12 Jan 2023) SHEET 4 OF 5 Applicant: Motorola Solutions Inc FCC ID: AZ489FT7162 / IC: 109U-89FT7162 Figure 4: FCC/IC Label for APX N30 Hazloc

*** END ***

EXHIBIT 1 Revision 2 (12 Jan 2023) SHEET 5 OF 5

 

 

FCC ID: AZ489FT7162 Date: July 25, 2023 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation Statements pursuant to Part 2.911 (d)(5)(i) with FCC ID: AZ489FT7162 Dear Sir/Madam, According to FCC 22-84 and KDB 986446, Motorola Solutions, Inc (8000 West Sunrise Boulevard, Fort Lauderdale, Florida) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, ________________________________________ Deanna Zakharia Regulatory Compliance Manager E-mail: Deanna.zakharia@motorolasolutions.com _______________________________________________________________________________________________________________________ Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 EXHIBIT 13e Revision 1 (30 Jan 2023) FCC ID: AZ489FT7162 Date: July 25, 2023 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation Statements pursuant to Part 2.911 (d)(5)(ii) with FCC ID: AZ489FT7162 Dear Sir/Madam, According to FCC 22-84 and KDB 986446, Motorola Solutions, Inc (8000 West Sunrise Boulevard, Fort Lauderdale, Florida) certifies that as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely, _______________________________________ Deanna Zakharia Regulatory Compliance Manager E-mail: Deanna.zakharia@motorolasolutions.com _______________________________________________________________________________________________________________________ Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 EXHIBIT 13e Revision 1 (30 Jan 2023)

 

 

FCC ID: AZ489FT7162 Date: July 25, 2023 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Attestation Statements pursuant to Part 2.911 (d)(7) with FCC ID: AZ489FT7162 Dear Sir/Madam, This letter is to confirm that Motorolas Solutions Inc has a US Representative on behalf of all future FCC certification/registrations. As the FCC Representative, we are aware of the requirements involved as outlined in the US applicable document (FCC 22-84 and KDB 986446). US Representative Company Name: Motorola Solutions FRN Number: 0003778479 Company Grantee Code: AZ4 Contact Name: Deanna Zakharia Address: 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 Telephone Number: (954) 723-4707 E-mail: Deanna.zakharia@motorolasolutions.com Applicant Company Name: Motorola Solutions Company Grantee Code: AZ4 Contact Name: Deanna Zakharia Address: 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 Telephone Number: (954) 723-4707 Sincerely, _______________________________________ Deanna Zakharia Regulatory Compliance Manager E-mail: Deanna.zakharia@motorolasolutions.com _______________________________________________________________________________________________________________________ EXHIBIT 13f Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 Revision 2 (24 Februray 2023)

 

 

 

 

 

 

BT and WIFI 2.4GHz / 5GHz Declaration To whom it may concern, This is a Bluetooth/WIFI 2.4GHz / 5GHz combination antenna with FCC/IC ID:

AZ489FT7162/109U-89FT7162 . This Bluetooth/WIFI 2.4GHz / 5GHz co-existence mechanism is to ensure that the Bluetooth and WIFI 2.4GHz / 5GHz transmitters would not simultaneously operate. Therefore, Bluetooth and WIFI 2.4GHz / 5GHz antennas in FCC/IC ID:AZ489FT7162/109U-89FT7162 should not be considered to be able to transmit simultaneously. Though the users can use Bluetooth and WIFI 2.4GHz / 5GHz simultaneously, the real situation is that Bluetooth and WIFI 2.4GHz / 5GHz are used by time sharing and no overlap transmission. Should you have any questions, please have my best attention. Sincerely yours,

Name: Lim Hsiu Chong Title: Engineering Manager Tel: +6010-2213426 E-mail: hsiuchong@motorolasolutions.com Date: 15 th June 2023 EXHIBIT 2 Revision 2b (2 Feb 2023) SHEET 1 OF 3 WLAN Channels and Mode Declaration We, Motorola Solutions, Inc. , declare that the device, FCC ID: AZ489FT7162 , does not support any non-US channels in all the operational mode(s) in the US market. All non-US frequencies, US 2.4G channel 12-13 and Country code selection are disabled through proprietary software and are not user changeable. For ISED with IC: 109U-89FT7162 mode without active scanning function.

, the device operating in 5600-5650MHz band shall operate as client Should you have any question or comment regarding this matter, please do not hesitate to contact me. Sincerely yours,

Name: Lim Hsiu Chong Title: Engineering Manager Tel: +6010-2213426 E-mail: hsiuchong@motorolasolutions.com Date: 15 th June 2023 EXHIBIT 2 Revision 2b (2 Feb 2023) SHEET 2 OF 3 DTS-UNII Device Declaration Letter To whom it may concern, We have declared below featured for FCC equipment authorization, Device FCC ID: AZ489FT7162 DFS Device -- Master Client with Radar detection capability

(1)

, Client without radar detection capability N/A

(2) Active / Passive Scanning , ad-hoc mode access point capability Frequency Band

(MHz) 5150-5250 5250-5350 5470-5725 5725-5850 Active Scanning

(the device can transmit a probe

(beacon)) Yes , No Yes , No Yes , No Yes , No passive scanning

(where the device is can listen only with no probes) Yes , No Yes , No Yes , No Yes , No Ad Hoc Mode or WIFI Direct capability Yes , No Yes , No Yes , No Yes , No Access point capability Yes , No Yes , No Yes , No Yes , No Country code selection ability - Yes , No

(3) If yes, please explain how it was implemented: (please also help to provide detail of options for each country selection) Meet 15.202 requirement - Yes, No,

(4) A master device is defined as a device operating in a mode in which it has the capability to transmit without receiving an enabling signal. In this mode it is able to select a channel and initiate a network by sending enabling signals to other devices A client device is defined as a device operating in a mode in which the transmissions of the device are under control of the master. A device in client mode is not able to initiate a network. For client devices that have software configuration control to operate in different modes (active

(5) scanning in some and passive scanning in others) in different bands (devices with multiple equipment classes or those that operate on non-DFS frequencies) or modular devices which configure the modes of operations through software, the application must provide software and operations description on how the software and / or hardware is implemented to ensure that proper operations modes cannot be modified by end user or an installer. Apply, No Apply, (If apply, please help to provide explanation on it was implement, and how software was controlled) Factory set only.

Name: Lim Hsiu Chong Title: Engineering Manager Tel: +6010-2213426 E-mail: hsiuchong@motorolasolutions.com Date: 15 th June 2023 EXHIBIT 2 Revision 2b (2 Feb 2023) SHEET 3 OF 3

 

 

FCC ID: AZ489FT7162 CONFIDENTIALITY REQUEST July 25, 2023 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch FCC Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request for Transmitter with FCC ID: AZ489FT7162 Dear Sir / Madam, Motorola Solutions Inc is requesting that Exhibit 4 (Circuit Descriptions), Exhibit 5 (Schematic Diagrams), Exhibit 10 (Parts List and Tune Up Procedures), and Exhibit 12 (Operational Description) not be made routinely available for public inspection. Motorola Solutions Inc considers the information in these exhibits to be classified as trade secrets, pursuant to 47 CFR Section 0.457(d), 0.459 and Section 552(b)(4) of the Freedom of Information Act. Please mark Exhibits 4, 5, 10, and 12 as Confidential. Please contact me if you require any additional information. Sincerely, _______________________________________ Deanna Zakharia Regulatory Compliance Manager E-mail: Deanna.zakharia@motorolasolutions.com _______________________________________________________________________________________________________________________ Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 EXHIBIT 13b(i) Revision 1 (2 Aug 2022)

 

 

FCC ID: AZ489FT7162 Date: July 25, 2023 Office of Engineering and Technology Laboratory Division Equipment Authorization Branch Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Application for New Filing Certification of Transmitter with FCC ID: AZ489FT7162 Dear Sir/Madam, Motorola Solutions, Inc (8000 West Sunrise Boulevard, Fort Lauderdale, Florida) herein submits application for Certification of the subject transmitter. This transmitter is intended for use in a portable radio application with capabilities for clear and coded communications with a variable transmit power operating within the following frequency ranges:

Product Name Model Numbers Frequency Range RF Power FCC Rules Part LMR:

136 - 174 MHz 5.9W (Max declared) 22, 74, 80, 90 APX N50 H25KDF9PW6AN H25KDF9PW6AN-H BT:

2402-2480 MHz 10.76mW (max measured conducted peak) BTLE 4.0:

2402-2480MHz 6.31mW (max measured conducted peak) APX N30 H15KDF9PW6AN H15KDF9PW6AN-H WLAN 802.11 b/g/n:

2412-2462 MHz 280.54mW (max measured conducted peak) WLAN 802.11 a/n/ac:

5180-5825 MHz 22.08mW (max measured conducted average) 15C 15C 15C 15E We are requesting certification under Part(s) of the Commissions Rules listed above to allow operation of this equipment. The subject transmitter complies with Section 90.203(e) and 80.203(b) of the Rules in that the operator cannot directly program transmit frequencies using the unit's normally accessible external controls. A complete Certification application is enclosed. If you require any additional information, please contact me at (954) 723-4707. Sincerely, _______________________________________ Deanna Zakharia Regulatory Compliance Manager E-mail: Deanna.zakharia@motorolasolutions.com _______________________________________________________________________________________________________________________ Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 EXHIBIT 13A Revision 3 (9 Sept 2022)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Applicant: Motorola Solutions Inc FCC ID: AZ489FT7162/ IC: 109U-89FT7162 EXHIBIT 2 Statement of Certification

(Pursuant to FCC Part 2.907, 2.908 and RSP 100 Sec 4) 2.1 Statement of Certification Transceiver type described herein (AZ489FT7162/109U-89FT7162) is in compliance with all applicable parts of the FCC rules and ISED RSS standards. This device is P25 Compliant as well which meets FCC Part 90.548 and RSS 119 Section 5.11 as declared in exhibit 12. Each unit manufactured, imported, or marketed will conform to the samples tested herein, within the statistical variations that can be expected due to high volume production and test measurement error. NAME:

Lim Hsiu Chong SIGNATURE:

DATE:

12th June 2023 TITLE:

Engineering Manager EXHIBIT 2a Revision 1 (2 Aug 2022) SHEET 1 OF 2 Applicant: Motorola Solutions Inc FCC ID: AZ489FT7162/ IC: 109U-89FT7162 2.2 Attestation Statement (Equipment Class DTS and DSS Bluetooth/WiFi) This device contains an embedded Bluetooth device and WiFi device that are compliant with the applicable FCC Part 15C and ISED RSS 247 regulations. Part 15.247 (a)(1) / RSS 247 Section 5.1 The hopping sequence must be pseudo random. Each frequency must be used equally on the average by each transmitter The receivers input bandwidth is approximately equal to the transmit bandwidth The receiver hops in sequence with the transmitted signal Part 15.247 (g) / RSS 247 Section 5.1 The system is designed to comply with all of the regulations in this section when the transmitter is presented with a continuous data (or information) Part 15.247(h) / RSS 247 Section 5.1 The system does not coordinate its channel selection/hopping sequence with other frequency hopping systems for the express purpose of avoiding the simultaneous occupancy of individual hopping frequencies by multiple transmitters. NAME:

Lim Hsiu Chong SIGNATURE:

DATE:

12th June 2023 TITLE:

Engineering Manager EXHIBIT 2a Revision 1 (2 Aug 2022) SHEET 2 OF 2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FCC ID: AZ489FT7162 July 25, 2023 Authorization & Evaluation Division Federal Communications Commission Laboratory 7435 Oakland Mills Road Columbia, MD 21046 Subject: Extended Frequencies Justification for Certification of Transmitter with FCC ID: AZ489FT7162. Dear Sir/Madam:

This transmitter is designed to operate in the frequency ranges as described in Exhibit 13a. To aid equipment authorization in other countries which accept the United States FCC Grant for Certification, Motorola Solutions is requesting that the FCC lists the above applicable frequencies range under FCC Rule Parts 22, 74, 80, and 90 on the FCC Grant. For the FCCs Rule Parts 22, 74, 80 and 90 applications, this radio is used in systems by Federal and Public Safety agencies including Police, Fire, and Emergency Medical Services, etc. as indicated in the table below. Equipment programming is the responsibility of Authorized Service Personnel. Also, the radio complies with 47 CFR Part 90.203(e) and 80.203(b), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Per the FCCs KDB634817 guidance, as an alternative to listing the exact frequencies, we acknowledge that its a violation of the FCC Rules if this device operates on unauthorized frequencies. Frequency Range

(MHz) 136-150.8*

150.8-152.855 152.855-154 154-156.2475 156.2475-157.1875 157.1875-157.45 157.45-161.575 161.575-161.625 161.625-161-775 161.775-161.9625 161.9625-162.025 162.025-162.0375*

162.0375-173.4 173.4-174*

*Canada Part 22 Part 24D Part 74 Part 80 Part 90 Federal x Other Regions x x x x x x x x x x x x x x x x x x x x x x x Please contact me if you require any additional information. Sincerely, ________________________________________ Deanna Zakharia Regulatory Compliance Manager E-mail: Deanna.zakharia@motorolasolutions.com _______________________________________________________________________________________________________________________ Motorola Solutions Inc. 8000 West Sunrise Boulevard, Fort Lauderdale, Florida 33322 EXHIBIT 13C Revision 1 (2 Aug 2022)