FCC ID: AZ489FT7142 VB400

VB400 BODY-WORN CAMERA QUICKSTART GUIDE 1 TABLE OF CONTENTS INTRODUCTION HOW TO CHARGE YOUR VB400 CHARGING WITH A 1-PORT DOCK CHARGING WITH A 14-PORT DOCK BATTERY STATUS LED CONFIGURING YOUR VB400 IDENTIFYING AN RFID ASSIGNED VB400 USING YOUR VB400 WEARING YOUR VB400 ACCESSORIES REGULATORY INFORMATION TO START / STOP RECORDING 3 4 5 6 7 8 9 10 10 12 13 14 2 INTRODUCTION Thank you for choosing the VB400 Body-worn camera. This simple guide will lead you through the set up and use of your VB400. Lens Function Button A LED Function Button B LED Slider LED Function Button C Dual Microphone Front Function Button Buzzer Speaker 3 HOW TO CHARGE YOUR VB400 Upon receiving your VB400, it is recommended that you fully charge the device before usage. When charging using a 1-Port Dock or 14-Port Dock, insert the camera into the slots as shown below, ensuring the camera clicks securely in place. Check that the top LED blinks green to indicate charging. Slide down to click into place 4 CHARGING WITH A 1-PORT DOCK

(VB-400-DOCK-SOLO) Connected to your laptop or DockController. If you are charging your VB400 camera via a 1-Port Dock

(VB-400-DOCK-SOLO) your camera will bleep to indicate charging has commenced, and the LED, as indicated, will flash green to show charging. Charging: Flashing green LED Fully Charged: Solid green LED Once fully charged, the same LED will turn solid green. If the LED is not lit, the device is not charging. Your VB400 will be fully charged within 8 hours from a flat battery. 5 CHARGING WITH A 14-PORT DOCK

(VB-400-DOCK-14/US) Connected to a power supply and DockController If you are charging your VB400 camera via a 14-Port Dock (VB-400-DOCK-14/US) the top LED will flash green to show charging, and the camera will bleep when successfully connected to VideoManager. Charging: Flashing green LED Fully Charged: Solid green LED Once fully charged, the same LED will turn solid green. If the LED is not lit, the device is not charging. Your VB400 will be fully charged within 8 hours from a flat battery. 6 BATTERY STATUS LED To quickly understand the current battery status of your VB400, press the bottom button on the front face of the camera and refer to the bottom LED. COLOR KEY:

Green LED: OK Orange/Yellow LED: Low Red LED: Critical Battery Status Button

(Configurable) 7 CONFIGURING YOUR VB400 Prior to using your VB400, your device must be configured and assigned to you using VideoManager. For detailed information on how to configure your device, please refer to the VideoManager User Guide. Each VB400 requires a valid VideoManager Licence, in order for you to assign devices and access footage. For further details, see the VideoManager User Guide. To ascertain whether your VB400 has been configured, please view the top LED on your device. This LED will turn solid green once configured and assigned. Your VB400 is charged, assigned and ready to use when the LEDs shown are both solid green. PLEASE NOTE: If you try to use your VB400 before it has been assigned, the bottom LED on the front face of the camera will start to flash red and you will hear an alarm tone. You will not be able to use your camera until it has been assigned. Configured, charged &

assigned Solid green light 8 IDENTIFYING AN RFID ASSIGNED VB400 Once your device is configured, your system administrator may wish camera users to utilize an RFID system for camera assignment. For further information on assigning VB400s using an RFID reader, please refer to the VideoManager User Guide. Having presented your RFID card, your docked, assigned VB400 will identify itself with a solid red LED as shown. RFID-Card

(RF-CARD-10) RFID Assigned Camera RFID Reader

(RF-220) 9 USING YOUR VB400 The VB400 series of cameras are intuitive and simple to use. TO START / STOP RECORDING (CONFIGURABLE) Users can activate recording by pressing on the single front button located in the center of the camera as shown. Recording is stopped by pressing and holding the front button. Record activation and deactivation buttons are configurable by Administrators. Start Recording initiated will be indicated by a short bleep, the two upper LEDs showing red. Press center button to start / stop recording Solid red LED 10 Stop Recording initiated is indicated by the two upper LEDs turning from red to off, accompanied by a longer, high pitched bleep. PLEASE NOTE: All buttons are configurable. Please consult with your administrator if you have any issues. Power Down Button

(Configurable) No LED 11 WEARING YOUR VB400 The VB400 body-worn camera should always remain upright when capturing footage. 12 ACCESSORIES Designed for optimum performance and comfort in a wide range of situations, the VB400 comes with a variety of fixing types to suit every uniform and body shape. For more information on our range of body-worn cameras, please visit: www.motorolasolutions.com/bwc 13 REGULATORY INFORMATION FCC Responsible party Name: Motorola Solutions, Inc. Address: 2000 Progress Pkway, Schaumburg, Il. 60196 Phone Number: 1-800-927-2744 Hereby declares that the product:

Model Name: VB400 Conforms to the following regulations: FCC Part 15, subpart B, section 15.107(a), 15.107(d), and section 15.109(a) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. The device must not be co-located or operating in conjunction with any other antenna or transmitter. FCC RF EXPOSURE INFORMATION (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. 14 INDUSTRY CANADA STATEMENT This device complies with RSS247 of Industry Canada. Cet appareil se conforme RSS247 de Canada dIndustrie. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prejudiciable, et (2) ce dispositif doit accepter tout brouillage recu, y compris un brouillage susceptible de provoquer un fonctionnement indesirable. The device must not be co-located or operating in conjunction with any other antenna or transmitter. CAUTION:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment complies with the e.i.r.p. limit;

(iii) the maximum antenna gain permitted for devices in the band 5275-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and

(iv) the worst-case tilt angle(s) necessary to remain compliant with the e.i.r.p. elevation mask requirement set forth in Section 6.2.2(3) shall be clearly indicated.

(v) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. EXPOSURE OF HUMANS TO RF FIELDS (RSS-102) The radiated energy from the antennas connected to the wireless adapters conforms to the IC limit of the RF exposure requirement regarding IC RSS102, Issue 5 clause 4. SAR tests are conducted using recommended operating positions accepted by the RSS with the device transmitting at its highest certified power level in all tested frequency band without distance attaching away from the body. CONFORMIT DES APPAREILS DE RADIOCOMMUNICATION AUX LIMITES DEXPOSITION HUMAINE AUX RADIOFRQUENCES (CNR-102) Lnergie mise par les antennes relies aux cartes sans fil respecte la limite dexposition aux radiofrquences telle que dfinie par Industrie Canada dans la clause 4.1 du document CNR-102, version 5. Tests DAS sont effectus en utilisant les positions recommandes par la CNR avec le tlphone met la puissance certifie maximale dans toutes les bandes de frquences testes sans distance attacher loin du corps. FOR COUNTRY CODE SELECTION USAGE (WLAN DEVICES) NOTE: The product does not have a country code selection feature. Per FCC regulations, all Wi-Fi products marketed in US must be fixed to US operation channels only. 1. Warning: For acceptance of the external DC source shall comply with ES1, PS2 requirements. 2. WARNING: The batteries shall not be exposed to excessive heat such as sunshine, fire or the like. 3. CAUTION: Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type. The apparatus shall be used Battery disposal information The battery used with this product contains chemicals that are harmful to the environment. 4. To preserve our environment, dispose of the battery according to your local laws and regulations. 5. Do not dispose of the battery with normal household waste, 6. For more information, please contact the local authority or the retailer where you purchased the product. RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment. 15 For more information, please visit: www.motorolasolutions.com/BWC Motorola Solutions, Inc. 500 West Monroe Street, Chicago, IL 60661, U.S.A. 800-367-2346 Availability is subject to individual country law and regulations. All specifications shown are typical unless otherwise stated and are subject to change without notice. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. 2020 Motorola Solutions, Inc. All rights reserved. (08/20) (ED-006-021-13-US)

Label and Location Label size 41*17mm

775 Mont tague Expresswa M Milpitas, CA 9503 T Tel: 408-526-118 F Fax: 408-526-108 bureauveritas.co il: certification@b ttps://www.cps.b bureauveritas.com ay 35 88 88 om m/

Emai Website: h P Proje C Certi ificat ect a tion and P Rep Prod prese uct entat tive R Reason for Ame endment (curre nt / obsolete) Initial Revised Updated com Updated lette Added FC Updated comp Updated Refe Release (obsol d wording (obso mpany template er information (

CC ID field (obs pany name & lo erences and Co ete) olete)

(obsolete)

(obsolete) solete) go (current) ontact info Re Fro evision History y T m To 1.0 0 1.0 0 2.0 0 3.0 0 4.0 0 5.0 0 6.0 0

.0 1 2.0 2 3 3.0 4 4.0 5 5.0 6 6.0 7 7.0 Approved Date e Nov-14-2006 Sept25-2007 Jan-31-2012 May-23-2014 Sep-16-2014 Jun-27-2018 Aug-30-202 A Auth horiz ation n Let tter SCS-F 018: Project and d Product Certifi cation Represen ntative Authoriza ation Letter Pa age 1 of 3 Rev 7 7.0 roduct Certific cation Repres sentative Auth horization Lett ter _____Motoro ces, Inc. to ac la Solutions ct as a Certific

, Inc._____ h cation Body fo ereby authori or certifying fo ize Bureau Ve or the following eritas Consum g project(s):

mer Product Motorol a Solutions, Inc. 11.27 VCPS, INC. Montague Exp pressway, as, CA 95035 5 Sir/Madam, ID: AZ489FT uct Description l: VB400 T7142 n: VB400 rely, 2020. To: BV 775 M Milpita USA Dear Re: P We, _ Servic FCC I Produ Mode Since Client Client Conta Ft.Lau ts signature ts name / title act information uderdale FL 3 e : Deanna Za n / address: 8 33322, USA akharia/ Mana 8000 West Su ager,Regulato nrise Blvd ry Complianc ce SCS-F 018: Project and d Product Certifi cation Represen ntative Authoriza ation Letter Pa age 2 of 3 Rev 7 7.0

775 Montague Expressway Milpitas, CA 95035 Tel: 408-526-1188 Fax: 408-526-1088 Email: certification@bureauveritas.com Website: https://www.cps.bureauveritas.com/

Confidentiality Request Letter Revision History From Reason for Amendment (current / obsolete) Initial Release (obsolete) Adding CFR 2.459 (obsolete) Updated company template & Added text box Added IC confidentiality letter form (obsolete) Corrections to STC form. Added reference to KDB

(obsolete)

(obsolete) Updated company logo (current) Updated References and Contact Info 1.0 1.0 2.0 3.0 4.0 5.0 6.0 To 1.0 2.0 3.0 4.0 5.0 6.0 7.0 Approved Date Nov-14-2006 August 11 - 2008 Jan-31-2012 March-26-2015 Nov-19-2015 Jun-26-2019 Aug-30-2020 SCS-F019: Confidentiality Request Letter Page 1 of 2 Rev 7.0 Motorola Solutions, Inc. 2020.12.14 To:

Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046-1609 Cc:

Bureau Veritas Consumer Products Services Inc. 775 Montague Expressway Milpitas, CA 95035 Subject: Confidentiality Request for FCC ID: AZ489FT7142 Pursuant to CFR 47 sections 0.457 and 0.459, we respectfully request permanent confidential treatment of the following Exhibits accompanying this application be held confidential:

Type of Confidentiality Requested Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Short Term Permanent Permanent i Permanent Permanent Permanent Permanent Permanent i Permanent i Exhibit Block Diagram External Photos Internal Photos Operational Description/ Theory of Operation Parts List Tune-Up Procedure Schematics Test Setup Photos Users Manual SOFTWARE SECURITY REQUIREMENTS FOR U-NII DEVICES The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Permanent Confidentiality:

The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality:

To avoid premature release of sensitive information prior to marketing or release of the product to the public, the applicant requests the following documents contained in this certification application be temporarily withheld from public disclosure for an initial period of 45 or 180 The applicant understands that disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. days; or for a specified date of not to exceed 180 days from the Grant Date Sincerely,Clients signature Clients name / title : Deanna Zakharia/ Manager,Regulatory Compliance Contact information / address: 8000 West Sunrise Blvd Ft.Lauderdale FL 33322, USA i Permanent confidentiality may be requested in accordance with FCC KDB 726920 SCS-F019: Confidentiality Request Letter Page 2 of 2 Rev 7.0

WIFI Channel 12 and 13 Declaration Letter Reason for Amendment Approved Date Revision History Initial Release (obsolete) Modify the select options (current) December 22, 2015 September 23, 2016 From Initial 1.0 To 1.0 2.0 SCSF190WiFiChannel12&13DeclarationLetter CreatedbyWilliamGraff Page1of2 Rev.2.0 ApprovedbyBaoThuongNguyen Motorol a Solutions, Inc. We declare t WIFI Ch he equipment hannel 12 a identified below FCC ID:

and 13 Dec w with regards AZ489FT71 claration Le to Channel 12 142 etter 2 and 13 capab bilities for Dec claration Prod duct hardware e does not hav ve the capabi lity to operate e on Channel 12 and 13. Prod thes duct hardware e two channe e has the capa els will be disa ability to opera abled via softw ate on Chann ware and will nel 12 and 13. not be access

. However, sible to user. Prod the o chan Prod mee duct hardware operated chan nnels have co duct hardware ts the require 1.) By defaul requireme 2.) This devic 2 to determ power. Su e has the capa nnels cant be omplied with a e has the capa ements of KDB lt, this device ents. ce will also us mine that it is o uch suppleme ability to opera e changed in t all of the requi ability to opera B 594280 D01 operates in a ate on Chann the RF param rements sets ate on WiFi C 1 v02r01. Plea a mode that is nel 12 and 13. meter via softw out in FCC P Channel 12 an ase note:

compliant wi

. However, all l ware. All Part 15.247. nd 13, and th the U.S. se supplemen operating outs ental data will ntal informatio side the U.S., be derived fr on such as ge if necessary, rom the follow wing:

o-location dat ta s to change its Glob bal Navigation n Satellite Sys stem (GNSS) 7 sensors in t the device Mob from ile Country C m a CMRS9 ca ode (MCC),8 arrier and rece or MCC with eived directly a Mobile Netw by a receiver MNC), received work code (M d e r on the device Coun IEEE ntry informatio E Std 802.11d on derived fro d provisions) m om multiple ad may be permi djacent acces tted on case-

example using ss points (for e g s

-by-case basis Othe er suitable geo o-location dat ta based on IP P addresses o or other reliab ble source. Name / T Title: Deanna a Zakharia /

Manager,Re egulatory Co ompliance Signature e:

Phone: (9 Email: De Date:202 954)723-470 eanna.zakha 20.11.27 07 aria@motoro olasolutions

.com SCSF190WiF CreatedbyW WilliamGraff FiChannel12&13 DeclarationLetter r Page2of2 Rev.2.0 Approve edbyBaoThuong Nguyen