Moxa 2.4/4.9/5 GHz WAPN008-1 Users Manual www.moxa.com First Edition, May 2019 2019 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. WAPN008-1 Users Manual The hardware and software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright 2019 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. Trademarks All other trademarks or registered marks in this manual belong to their respective manufacturers. MOXA is a registered trademark of Moxa Inc. Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa. Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the products and/or the programs described in this manual, at any time. Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from its use. This product might include unintentional technical or typographical errors. Changes are periodically made to the information herein to correct such errors, and these changes are incorporated into new editions of the publication. Technical Support Contact Information www.moxa.com/support Moxa Americas:
Toll-free: 1-888-669-2872 Tel:
+1-714-528-6777
+1-714-528-6778 Fax:
Moxa China (Shanghai office):
Toll-free: 800-820-5036 Tel:
Fax:
+86-21-5258-9955
+86-10-6872-3958 Moxa Europe:
Tel:
Fax:
+49-89-3 70 03 99-0
+49-89-3 70 03 99-99 Moxa Asia-Pacific:
Tel:
Fax:
+886-2-8919-1230
+886-2-8919-1231 Table of Contents Chapter 1 Introduction Overview Specification Chapter 2 Getting Started Module Layout Block Diagram Hardware Installation Software Installation WAPN008-1 Users Manual Introduction 1 Chapter 1 Introduction The following topics are covered in this chapter:
Overview Specifications WAPN008-1 Users Manual Introduction Overview WAPN008-1 PCI module is designed to provide wireless communication for Moxa industrial wireless products. It communicates via 2.4 GHz/4.9 GHz/5 GHz channels. The WAPN008-1 uses the AR9344 SoC Wireless chipset from Atheros. WAPN008-1 Atheros AR9344
- 64-bit and 128-bit WEP encryption, WPA /WPA2-Personal and Enterprise (IEEE 802.1X/RADIUS, TKIP and AES) Defined BTB connector is using 2x40 pins header, and Support PCI Express standard. 60mm x 60mm x 1.2mm
-40 to +80 (installed properly inside the enclosure of the final products)
-40 to +150 (installed properly inside the enclosure of the final products) Specification Features Chipset security engine Connectors Power requirement 3.3V +/-10%
Dimension Operating Temperature Storage Temperature:
Operates in 2.4 and 5 GHz frequency bands.
(frequency range) US:
2,400 to 2,483.5 MHz 4,940 to 4,990 MHz 5,725 to 5,850 MHz EU:
2,400 to 2,483.5 MHz 5,725 to 5,875 MHz 2 Chapter 2 Getting Started This chapter covers the module layout, and block diagram, hardware installation of the WAPN008-1. Software installation is covered in the next chapter. The following topics are covered:
Module Layout Block Diagram Hardware Installation Software Installation WAPN008-1 Users Manual Getting Started Module Layout Top and Bottom Block Diagram Below is a block diagram of the WAPN008-1. WAPN008-1 Users Manual Getting Started Connector Locations WAPN008-1 Users Manual Getting Started PCI Bus Connector PIN Assignments Function Connect to Pin Pin Function Connect to GND GND ERXD3 ERXD2 ERXD1 ERXD0 GND GND ETX_CLK GND GND ETX_EN GND GND ETXD3 ETXD2 ETXD1 ETXD0 GND GND ERX_CLK GND GND ERX_EN GND GND EMDC EMDIO GND GND TXP0 TXN0 GND RXP0 RXN0 GND GND USB_DM USB_DP GND 3.3v 3.3v 3.3v 3.3v 3.3v 3.3v 3.3v GPIO 16 GPIO 17 GND GPIO 21 GPIO 1 GND GPIO 4 GND GPIO 0 GND GPIO 3 GPIO 9 GPIO 10 GPIO 13 GPIO 14 GPIO 20 GND GPIO 22 GND GPIO 2 GND GPIO 11 GND GPIO 12 GND GPIO 15 GND SYS_RST_L AVDD18 AVDD18 AVDD18 GND GND 3.3v 3.3v 3.3v 3.3v 3.3v 3.3v 3.3v I2C_SCLK I2C_DATA GND POWER 2 JP1 Debug GND S17_INT GND I2C_INT0 GND UR_DSR UR_SIN UR_SOUT MDC MDIO POWER 1 GND POWER 3 GND UR_DTR GND Reset GND LAN 10/100 GND Reserved GND GIGA PHY Reset Fast Ethernet bios Fast Ethernet bios Fast Ethernet bios GND GND 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 GND GND PHY RGMII PHY RGMII PHY RGMII PHY RGMII GND GND ETX_CLK GND GND ETX_EN GND GND PHY RGMII PHY RGMII PHY RGMII PHY RGMII GND GND ERX_CLK GND GND ERX_EN GND GND GIGA PHY GIGA PHY GND GND 10/100 LAN 10/100 LAN GND 10/100 LAN 10/100 LAN GND GND USB port USB port GND WAPN008-1 Users Manual Getting Started Hardware Installation The WAPN008-1 can be installed into all Moxa wireless system board series. Step for Installation 1. Install the WAPN008-1 PCI card on the system board. Apply pressure to both bus connectors and gently press the board onto the stack. The board should slide into the matching bus connectors. Do not attempt to force the board, as this can lead to bent/broken pins. 2. Screw on the WAPN008-1 PCI card. 3. Screw on the all the necessary chassis. Software Installation After physically installing the WAPN008-1, your operating system must be configured to recognize the new system board. Step for Installation 1. Apply power to the system board. 2. Connect system board and PC with Ethernet cable. 3. Open a browser and type: 192.168.127.253 to open the system login webpage. 4. Login the webpage with default password: root in order to verify that all of the hardware is install properly. WAPN008-1 Users Manual Getting Started Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution:
To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
This module is restricted to mobile configuration. To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: SLE-WAPN008-1 WAPN008-1 Users Manual Getting Started Information for the OEMs and Integrators Any party of the installer who likes to use the module of 4.9GHz band shall fulfill licensing requirement (90.1207). The installation to Aeronautical mobile operations are prohibited (90.1205). The end product with an embedded WAPN008-1 module may also need to pass the FCC Part 15 unintentional emission testing requirements and be properly authorized per FCC Part 15. The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. This radio transmitter FCCID: SLE-WAPN008-1 has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Maximum Permissible Exposure (MPE): Ensure that at least 50 cm separation distance is maintained between the wireless module and the body of the user, when Panel antennas, ANT-WSB5-PNF-18 or ANT-WDB-PNF-1518, are used. Antenna List No. Manufacturer Part No. Antenna Type Peak Gain 1 2 3 4 5 6 7 8 9 MOXA ANT-WDB-ANM-0306 Dipole MOXA ANT-WDB-ARM-0202 Dipole MOXA ANT-WDB-ARM-02 Dipole MOXA ANT-WDB-ANM-0502 MOXA MOXA MOXA ANT-WSB5-ANF-12 ANT-WSB5-PNF-18 ANT-WDB-PNF-1518 Huber+Suhner Huber+Suhner 1356.17.0042 1356.17.0077 Dipole Dipole Panel Panel Railway Dipole 3.8dBi For 2.4 GHz 6.3dBi For 4.9 GHz 6.3dBi For 5 GHz 1.8dBi For 2.4GHz 1.8dBi For 4.9 GHz 1.8dBi For 5 GHz 2.04dBi For 2.4GHz 0.81dBi For 4.9 GHz 0.81dBi For 5 GHz 4.62dBi For 2.4GHz 2dBi For 4.9 GHz 2dBi For 5GHz 12dBi For 5 GHz 18dBi For 5 GHz 15dBi For 2.4GHz 18dBi For 5GHz 13dBi For 5GHz 14dBi For 5GHz WAPN008-1 Users Manual Getting Started