Moxa 802.11 b/g/n WAPN010 Users Manual www.moxa.com First Edition, April 2018 2018 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. WAPN010 Users Manual The hardware and software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice Copyright 2018 Moxa Inc. All rights reserved. Reproduction without permission is prohibited. Trademarks All other trademarks or registered marks in this manual belong to their respective manufacturers. MOXA is a registered trademark of Moxa Inc. Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa. Moxa provides this document as is, without warranty of any kind, either expressed or implied, including, but not limited to, its particular purpose. Moxa reserves the right to make improvements and/or changes to this manual, or to the products and/or the programs described in this manual, at any time. Information provided in this manual is intended to be accurate and reliable. However, Moxa assumes no responsibility for its use, or for any infringements on the rights of third parties that may result from its use. This product might include unintentional technical or typographical errors. Changes are periodically made to the information herein to correct such errors, and these changes are incorporated into new editions of the publication. Technical Support Contact Information www.moxa.com/support Table of Contents Chapter 1 Chapter 2 Introduction Overview Specification Getting Started Module Layout Block Diagram Hardware Installation Software Installation WAPN010 Users Manual Introduction 1 Introduction Chapter 1 The following topics are covered in this chapter:
Overview Specifications WAPN010 Users Manual Introduction Overview WAPN010 PCIe module is designed to provide wireless communication for Moxa industrial wireless products. It communicates via the standard 802.11 b/g/n protocols on standard 2.4GHz channels. The WAPN010 uses the QCA99X4 SoC Wireless chipset from Qualcomm. Specification Features Chipset Baseband Processor (BBP) security engine Connectors Power requirement Dimension Operating Temperature Storage Temperature:
Operates in 2.4 and 5 GHz frequency bands. WAPN008 Qualcomm QCA99X4
- DSSS with DBPSK, DQPSK, CCK
- OFDM with BPSK, QPSK, 16QAM, 64QAM
-
-
802.11b: CCK @ 11/5.5 Mbps, DQPSK @ 2 Mbps, DBPSK @ 11 Mbps 802.11 g: 64QAM @ 54/48 Mbps, 16QAM @ 36/24 Mbps, QPSK @ 18/12 Mbps, BPSK @ 9/6 Mbps 802.11n: 64QAM @ 300 Mbps to BPSK @ 6.5 Mbps (multiple rates supported)
-
- 64-bit and 128-bit WEP encryption, WPA /WPA2-Personal and Enterprise (IEEE 802.1X/RADIUS, TKIP and AES) PCI Express Mini Card 3.3V +/-10%
60mm x 60mm x 1.2mm
-40 to 50
-40 to 85 US:
2.412 to 2.462 GHz (11 channels) EU:
2.412 to 2.472 GHz (13 channels) JP:
2.412 to 2.484 GHz (14 channels) 2 Getting Started Chapter 2 This chapter covers the module layout, and block diagram, hardware installation of the WAPN008. Software installation is covered in the next chapter. The following topics are covered:
Module Layout Block Diagram Hardware Installation Software Installation WAPN010 Users Manual Getting Started Module Layout Top and Bottom Block Diagram Below is a block diagram of the WAPN008. WAPN010 Users Manual Getting Started Connector Locations WAPN010 Users Manual Getting Started mPCIe Bus Connector PIN Assignments Function Connect to Pin Pin Function Connect to WAKE_L WAKE_L RESERVED RESERVED CLKREQ_L NC NC NC GND GND REFCLK-
REFCLK-
REFCLK+
REFCLK+
GND UIM_C8 UIM_C9 GND PERn0 PERp0 GND GND PETn0 PETp0 GND RESERVED RESERVED RESERVED GND NC NC GND PERn0 PERp0 GND GND PETn0 PETp0 GND NC NC NC RESERVED GND RESERVED DVDD33 RESERVED DVDD33 RESERVED DVDD33 RESERVED DVDD33 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 3.3V GND 1.5V UIM_PWR UIM_DATA UIM_CLK UIM_RESET UIM_VPP DVDD33 GND NC NC NC NC NC NC GND GND W_DISABLE_L GPIO18 RESET_L RESET_L 3.3VAUX DVDD33 GND 1.5V SMB_CLK SMB_DATA GND NC NC NC GND GND USB_D-
USB_D+
NC NC GND GND LED_WWAN_L NC LED_WLAN_L GPIO17 LED_WPAN_L 1.5V GND 3.3V NC NC GND DVDD33 WAPN010 Users Manual Getting Started Hardware Installation The WAPN010 can be installed into all Moxa wireless system board series. Required Professional Installation Step 1. Install the WAPN010 PCIe card on the system board. Apply pressure to both bus connectors and gently press the board onto the stack. The board should slide into the matching bus connectors. Do not attempt to force the board, as this can lead to bent/broken pins. 2. Screw on the WAPN010 PCIe card. 3. Screw on the all the necessary chassis. Software Installation After physically installing the WAPN010, your operating system must be configured to recognize the new system board. Required Professional Installation Step 1. Apply power to the system board. 2. Connect system board and PC with Ethernet cable. 3. Open a browser and type: 192.168.127.253 to open the system login webpage. 4. Login the webpage with default password: root in order to verify that all of the hardware is install properly. WAPN010 Users Manual Getting Started Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution:
To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices) any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
This module is restricted to mobile configuration. To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 40cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This transmitter module must not be co-located or operating in conjunction with any other antenna or transmitter CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 40cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains FCC ID: SLE-WAPN010 WAPN010 Users Manual Getting Started Canada, Industry Canada (IC) Notices This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Canada, avis d'Industry Canada (IC) Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Devraient galement tre informs les utilisateurs que les radars haute puissance sont dsigns comme utilisateurs principaux (c.--utilisateurs prioritaires) des bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient provoquer des interfrences et / ou endommager les appareils LE-LAN. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure conditions. (antennas are greater than 20cm from a person's body). Informations concernant l'exposition aux frquences radio (RF) La puissance de sortie mise par lappareil de sans fil est infrieure la limite d'exposition aux frquences radio d'Industry Canada (IC). Utilisez lappareil de sans fil de faon minimiser les contacts humains lors du fonctionnement normal. Ce priphrique a galement t valu et dmontr conforme aux limites d'exposition aux RF d'IC dans des conditions d'exposition des appareils mobiles (antennes sont suprieures 40 cm partir du corps d'une personne). End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 40cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains IC: 9335A-WAPN010 Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. WAPN010 Users Manual Getting Started Information for the OEMs and Integrators The following statement must be included with all versions of this document supplied to an OEM or integrator, but should not be distributed to the end user. 1) This device is intended for OEM integrators only. 2) Please see the full Grant of Equipment document for other restrictions. This radio transmitter FCCID: SLE-WAPN010 and IC: 9335A-WAPN010 has been approved by FCC/IC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Antenna List No. Manufacturer Part No. Antenna Type Peak Gain MAT-WDB-PA-NF-2-0708 ANT-WSB-PNF-18 WI25-A1-0810012-RG316 ANT-WSB-PNF-12 ANT-WDB-PNF-1518 ANT-WSB-AHRM-05-1.5m BK ANT-WSB-ANF-09 MAT-WDB-CA-RM-2-0205 Panel Panel Panel Panel Panel 7.63dBi For 2.4GHz 18dBi For 2.4GHz 8.5dBi For 2.4GHz 12dBi For 2.4GHz 15dBi For 2.4GHz Omni-directional 1.51dBi For 2.4GHz Omni-directional 9dBi For 2.4GHz Omni-directional 2.5dBi For 2.4GHz MAT-WDB-DA-RM-2-0203-1m Omni-directional 2.43dBi For 2.4GHz Omni-directional 3.8dBi For 2.4GHz Omni-directional 1.8dBi For 2.4GHz Omni-directional 2.04dBi For 2.4GHz Omni-directional 4.62dBi For 2.4GHz Omni-directional 4dBi For 2.4GHz Omni-directional 6dBi For 2.4GHz Omni-directional 6dBi For 2.4GHz Railway Sector Patch 9dBi For 2.4GHz 12dBi For 2.4GHz 8.2dBi For 2.4GHz ANT-WDB-ANM-0306 ANT-WDB-ARM-0202 ANT-WDB-ARM-02 ANT-WDB-ANM-0502 ANT-WDB-ANM-0407 ANT-WDB-ANF-0609 ANT-WDB-ANM-0609 MHH-A11-XX110170-X0 WI25-A1-1215053-X0 TOP 200 AMR MF-05-4 1 9 8 7 6 5 4 3 2 15 14 13 12 11 10 MOXA MOXA MOXA MOXA MOXA MOXA MOXA MOXA MOXA MOXA MOXA MOXA MOXA MOXA MOXA Note: The antenna connector is Reverse SMA type MOXA MOXA MOXA MOXA 17 18 19 16