S-TRX (-R4, -R6, -J) Clear Pat h Spectrum Transceiver with Surface Mouting Box Section 1 General Description ClearPath Spectrum radio control transceivers provide reliable activation of any automatic door, and feature several industry firsts. ClearPath Spectrum products feature digital increasing security and allowing users to pair transceivers to coordinators, and monitor battery power. With the ability to optional SecureActivation will require users of the outside switch to be granted clearance before activation can occur. two-way communication, transceivers location, identify by
= Spectrum Transceiver with 1020 Square Mounting Box - replaces CP/TX S-TRX S-TRX-R4 = Spectrum Transceiver with 1025 Round S-TRX-R6 = Spectrum Transceiver with 1030 Round S-TRX-J = Spectrum Transceiver with 1010 Jamb Mounting Box - replaces CP/TX-R4 Mounting Box - replaces CP/TX-R6 Mounting Box - replaces CP/TX-J INSTALLATION INSTRUCTIONS LOCK LIP B C P X T Battery PUSH PLATE SWITCH BACK PLATE FRAME 1/4-20 SCREW
(Rear View: S-TRX Shown) 2) Place coordinator into pairing mode. (See CS/COR coordinator instructions).. 3) Press PAIR button (Fig.2). FIGURE 2 Transmitter Circuit Board ClearPath Spectrum products operate at 2.4 GHz, making the wave length more than 5 times shorter than commonly-used frequencies. Shorter waves pass through cracks and barriers easier, and transmitters will continue to attempt to contact the coordinator until it receives an acknowledgement. Battery 1 Section 2 Basic Installation 1) Remove the 1/4-20 screw located in the bottom of the frame and separate the back plate from the frame (Fig.1). Secure the back plate in its intended location with at least 2 screws.
WARNING: Mounting screws must be flush with the back plate to ensure proper assembly. I R A P to the mounting box frame with the 6-32 screws provided with the push plate switch (Fig.1). 4) Attach the push plate switch (purchased separately) 5) Plug the 2-lead transmitter wire harness onto the COM (Common) and N.O. (Normally Open) contacts located on the push plate switch (Fig.3). PUSH TO OPEN PUSH PLATE SWITCH FIGURE 1 FRAME Battery BACK PLATE Rubber Bellows FIGURE 3 COM 1/4-20 SCREW Insert rubber bellows over spring on exterior switches for weather tight fit!
(Front View: S-TRX Shown)
. C N
. UL LISTED SPDT, Momentary RATED: 15A @ 125V A C
. O N
. MICRO-SWITCH Telephone: (800) 842-2545/(317) 842-2545 www.mssedco.com custsvc@mssedco.com 8701 Castle Park Drive Indianapolis, Indiana 46256 Page 1 S-TRXv0312 S-TRX (-R4, -R6, -J) ClearPat h Spectrum Transceiver with Surface Mouting Box INSTALLATION INSTRUCTIONS already mounted in its intended location (step 1) by placing the lock lip of the frame over the top of the back plate, pushing it down in a hinge-like motion
(Fig.1). 6) Attach the mounting box frame to the back plate 7) Secure the mounting box frame to its back plate at the underside with the 1/4-20 screw supplied (Fig.1).
NOTICE: This device complies with Part 15 of the FCC rules. Operation of this device is subject to the following two conditions: 1) This device may not cause harmful interference and 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by MS SEDCO could void the user's authority to operate this equipment. Section 3 Maintenance For best results, change the battery every 3 years, or as needed. To remove the current battery, use a small flat-head screwdriver, approaching from the PAIR button side of the pcb as shown (See Fig. 4). FIGURE 4 Transmitter Circuit Board Battery 1 I R A P Remove battery from this side. Telephone: (800) 842-2545/(317) 842-2545 www.mssedco.com custsvc@mssedco.com 8701 Castle Park Drive Indianapolis, Indiana 46256 Page 2 S-TRXv0312