1. Battery Replacement Release the lid screw and open the lid. Insert batteries
(2xAA) according to the "+" "-" signs. Green LED will illuminate for 2 seconds. Close the lid and tighten the screw. Touch [#] for 5 seconds. The reader will self calibrate, which will be followed by a series of beeps and blinking LEDs. 2. Pairing Fingerprint Reader This procedure is done via the smartphone application. See also: Pairing Touchpad Reader. Open the smartphone application. Press on the lock icon on the right side at the top. Press on lock settings from the list. Pairing failed 1 long beep emitted. Red LED illuminated for 2 seconds. In the app screen:
Pairing process had failed. Please try again. Matched Codes Mismatched Codes Option 2:
Touch the Fingerprint Touchpad. Screen prompts for user code. Enter your code
[OK]
User name added User name exists 9. Low-battery Indication Fingerprint Reader Low-battery Indication:
Red LED illuminates for 1 second after 2 long wake-up beeps are emitted. Type in owner password. 2 LEDs blinking in the door unit. The lock is waiting for the fingerprint to create the connection. Press #5 to wake-up the Fingerprint Touchpad. 3. Adjust Date & Time Note: At the end of the initial pairing process, a short notice will be displayed. Place finger on scanner, wait for beep, then swipe finger down several times over fingerprint scanner until two confirmation beeps emitted 4. Add Master User Setting a Master User requires both fingerprint and PIN code. It is possible to have up to two Master Users. Note: At any stage you can press and hold the [*] key to move to standby mode. Type in [Master name]
[OK]
Enter Date Press [OK]
Enter Time Press [OK]
Press [OK]
Set PIN code Set Finger Blue LED illuminates ADD USER SET FINGER Press [OK]
Green LED blinking Green LED blinking Place finger on scanner, wait for beep, then swipe finger down several times over fingerprint scanner until two confirmation beeps emitted. 5. Unlock the Door Note: verify the app is closed. Option 1:
Place finger on fingerprint scanner. Short beep emitted & white LED illuminates. Swipe finger over fingerprint scanner. Fingerprint authorized: Blue LED blinks and unlock command is sent. Fingerprint not authorized: Red LED illuminates. The device goes to standby. Note: In the event, the unlocking attempt fails, 1 long beep emitted. Red LED illuminated for 2 seconds. 6. Lock the Door Touch the Fingerprint Touchpad. Press [1]
7. Setting Menu
[#]
Touch screen Press [*]
Enter [Master PIN Code]
[OK] or swipe finger over fingerprint scanner 8. Add User The unit support up to 20 users. For each user, two different fingerprints and one PIN code. Use different user name for each user. 1 2 Press [OK]
Press [OK]
3 4 Type [USER NAME]
[OK]
Choose [OK] to add 2nd Master User or
[*] to add a user. Note: This screen will not appear if two Master Users are defined. Same user name. Choose different user name. 6 5 10. Delete Fingerprint Reader Press [OK] to set a finger or use [8]
or [2] in order to set a code only. Swipe 1st finger several times over fingerprint scanner until two confirmation beeps sound. 7 2nd finger added Swipe 2nd finger several times over fingerprint scanner until two confirmation beeps sound. 8 9 Press [OK] for YES or
[*] for NO 10 Type [CODE]
[OK]
Retype [CODE]
[OK]
Matched Codes Mismatched Codes Press on the remove switch. 11. Enable/Disable User Press Yes. Press [*]
Enter [Master PIN Code]
[OK] or swipe finger over fingerprint scanner 2 Press [OK]
Use [8] or [2]
to select:
[ENABLE USER]
[OK]
User enabled 1 3 ENABLE USER JENNIFER Disabled Use [8] or [2]
to toggle between users. Press [OK]
Note: Repeat this procedure to disable a user. 2 short beeps emitted. Press [OK]
Press on Additional Control Units. Press on + Add button located under Wall Reader. Note: during the pairing process 2 green lock signs blinking in the door unit. Pairing OK
[OK] indication blinks once. 2 short beeps emitted. Fingerprint Reader added. Press [OK]
Type in [PIN Code],
(4 to 10 digits). Press [OK]
Retype [PIN Code]
Press [OK]
11. Delete User Press [*]
Enter [Master PIN Code]
[OK] or swipe finger over fingerprint scanner 1 3 2 Press [OK]
Use [8] or [2]
to select:
[DELETE ALL]
4
[OK]
Notes:
1. Define up to 7 different time schedules for the same user. 2. Press [*] to go back on every menu. 3. Press [*] for 3 seconds to exit setting menu. 14. Edit Time Schedule 1 2 15. Volume Control 1 2 1 2 Press [*]
Enter [Master PIN Code]
[OK] or swipe finger over fingerprint scanner Use [8] or [2]
to select:
[DEVICE]
3
[OK]
Use [8] or [2]
to select:
[2xSecurity]
4
[OK]
Use [8] or [2]
to select:
[DELETE LOG]
[OK]
3 Press [OK]
Press [OK]
Press [OK]
Press [OK]
2 All users deleted Use [8] or [2]
to select:
[EDIT SCHED]
[OK]
1 2 17. Edit Log Press [OK]
Two beeps emitted. Green LED illuminates. 1 3 Press [OK]
Use [8] or [2]
to select:
[DELETE USER]
[OK]
4 User deleted Note: The first Master User can't be deleted without doing a factory reset. 12. Delete all Users Press [*]
Enter [Master PIN Code]
[OK] or swipe finger over fingerprint scanner Two beeps emitted. Green LED illuminates. 13. Add Time Schedule 1 2 Press [OK]
3 Use [8] or [2]
to select:
[ADD SCHED]
[OK]
4 Use [8] or [2]
to select a user
[OK]
Press 1-7 to choose a day. Example: 1 for Sunday 5 6 Enter END time Enter START time
[OK]
[OK]
7 3 4 Use [8] or [2]
to toggle between users
[OK]
Use [8] or [2] to choose the desired schedule to be edited. Pressing on [4] for 3 seconds shall delete the specific schedule. 5 6 Use [8] or [2] to change schedule day
[OK]
7 Use [8] or [2]
to change the START hour setting. Use [6 ] to move to START minutes. 8 Use [8] or [2]
to change START minutes setting. Use [6 ] to move to the END hour. Use [8] or [2]
to change END hour setting. Use [6 ] to move to the END minutes. 9 10 Use [8] or [2]
to select:
[DEVICE]
3
[OK]
Use [8] or [2]
to select:
[VOLUME]
4
[OK]
Press [OK]
Use [8] or [2]
to toggle between HIGH, MEDIUM or LOW. Two beeps emitted. Green LED illuminates. 16. Double Security After activating the double security option use both methods - swiping a fingerprint and inserting a PIN code to unlock the door. Note: User set up with only one of the settings (fingerprint or PIN code) will not be able to unlock the door. Press [*]
Enter [Master PIN Code]
[OK] or swipe finger over fingerprint scanner Press [*]
Enter [Master PIN Code]
[OK] or swipe finger over fingerprint scanner 1 2 Use [8] or [2]
to select:
[EDIT LOG]
[OK]
Use [6 ] or [4 ]
to toggle between events. 18. Delete Log Press [*]
Enter [Master PIN Code]
[OK] or swipe finger over fingerprint scanner 19. Error Codes Error Failed to unlock Failed to lock Unauthorized fingerprint Unauthorized Code 2xSecurity mismatch Device failure during operation Absent correct time/date in RTC User out of schedules Code#
01 02 03 04 05 06 07 08 For radio enclosure Federal Communications Commission (FCC) Statement labelling requirement for small device statement (FCC15.19 (3)) This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Radio Frequency Interference (RFI) (FCC 15.105). This equipment has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications Press [OK] for YES or
[*] for NO Two confirmation beeps emitted. Green LED illuminates. Use [8] or [2] to change END minutes setting. Press [OK] for YES or
[*] for NO. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/
TV technician for help. Labeling Requirements (FCC 15.19) This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications (FCC 15.21) Changes or modifications to this equipment not expressly approved by Mul-T-Lock may void the users authority to operate this equipment. RF Exposure info (FCC 2.1093)-for module radio This equipment has been approved for mobile applications where the equipment should be used at distances greater than 20cm from the human body (with the exception of hands, wrists, feet and ankles). Operation at distances less than 20cm is strictly prohibited. FOR MOBILE DEVICE USAGE (>20cm/low power) Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.