World leader in metal detection for anti-shoplifting purposes Quick pager MP10D Manual for World leader in metal detection for anti-shoplifting purposes TABLE OF CONTENTS 1. 2. 3. FEDERAL COMMUNICATIONS COMMISSION STATEMENT .......................................... 3 PAGER SYSTEM ................................................................................................................. 4 ADJUSTMENTS .................................................................................................................. 5 PAGER RECEIVER PROGRAMMING ........................................................................................... 5 PAGER RECEIVER RECHARGING .............................................................................................. 6 REPEATER UNIT ........................................................................................................................... 7 REPEATER SETUP ....................................................................................................................... 8 SPECIFICATIONS ............................................................................................................... 9 3.1 3.2 3.3 3.4 4. 900-1003114 Alert HyperGuard Quick pager MP10D (English V1) Page: 2/9 Date:May 31, 2013 World leader in metal detection for anti-shoplifting purposes 1. FEDERAL COMMUNICATIONS COMMISSION STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Modifications not expressly approved by this company could void the user's authority to operate the equipment NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The internal / external antennas used for this mobile transmitter must provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. 900-1003114 Alert HyperGuard Quick pager MP10D (English V1) Page: 3/9 Date:May 31, 2013 World leader in metal detection for anti-shoplifting purposes 2. PAGER SYSTEM Alert pager system with frequency bands: 426MHz, 433MHz and 915MHz Europe, Australia: 433MHz North America: 915MHz Japan: 426MHz Receiver Transmitter Repeater 900-1003114 Alert HyperGuard Quick pager MP10D (English V1) Page: 4/9 Date:May 31, 2013 World leader in metal detection for anti-shoplifting purposes 3. ADJUSTMENTS 3.1 Pager receiver programming Receiver ON/OFF ON: Press On/set. Two beeps and a vibration are indicated (if enabled). The LEDs shows a running light from left starting with blue, yellow, green and red Every 10 seconds a short flash in the green LED shows that the receiver is ON OFF: Press On/set and keep pressed until the LEDs shows a running light starting with red to blue. One beep and a vibration are indicated (if enabled). Manuel alarm reset Automatic alarm reset Repeat of the latest alarms Vibrator and beeper ON/OFF Coding of extra receiver The receiver shows an alarm by a flashing LED, a sound and a vibration. Press and hold OK 2 seconds to reset the alarm. Connect the receiver to the adaptor. Press OK and Menu at the same time for 3 seconds Two short beeps are heard and vibrator vibrates twice =
Automatic reset ON. Info in display: MSG TO ON One short beep is heard and vibrator vibrate once =
Automatic reset OFF. Info in display: MSG TO OFF The latest ten alarms are stored in the memory in the receiver. Press once on Menu shows the latest alarm. Press twice on Menu shows the second latest alarm. And so on. Connect the receiver to the adaptor. Press OK, the vibrator vibrates once = Vibrator OFF. In display: VIBR. OFF Press once again OK, the vibrator vibrates twice = Vibrator ON. In display: VIBR. ON Press Menu, the buzzer beeps once = Buzzer OFF Info in display: BUZZER OFF Press once again Menu, the buzzer beeps twice = Buzzer ON Info in display: BUZZER ON There are no limit in numbers of receivers that can receive info from one Transmitter. They only have to be coded to the transmitter. Make sure that the receiver is OFF. Press On/set and immediately (while LEDs shows a running light) after press OK until the blue and the red LEDs are flashing. Within 5 seconds press TEST on transmitter.
(Blue led next to TEST bottom flashes) Info in display: ASSIGN HOME ID If the coding is OK two short beeps are heard. If the coding fails one short beep is heard. 900-1003114 Alert HyperGuard Quick pager MP10D (English V1) Page: 5/9 Date:May 31, 2013 World leader in metal detection for anti-shoplifting purposes 3.2 Pager receiver recharging The battery capacity in the receiver is 2.4V 400mAH NiMH The receiver can with the battery fully charged operate app. 24 hours. It is highly recommended to recharge the receiver every time it is not in use, minimum once a day for at least 10 hours. Normally every night When the adaptor plug is connected to the receiver the following happens:
If the receiver is ON:
Receiver is set OFF All LEDs are flashing three times The red LED is flashing every 10 seconds Info in display: External supply applied High Batt. charge 10.00 If the receiver is OFF:
Two beeps and a vibration are indicated (if enabled). The LEDs shows a running light from left starting with blue All LEDs are flashing three times The red LED is flashing every 10 seconds Info in display: External supply applied High Batt. charge 10.00 When the adaptor plug is disconnected from the receiver the following happens:
The receiver is OFF 900-1003114 Alert HyperGuard Quick pager MP10D (English V1) Page: 6/9 Date:May 31, 2013 World leader in metal detection for anti-shoplifting purposes 3.3 Repeater unit Here is an example where the pager receiver cant receive the signal from the transmitter due to the concrete wall that is between the receiver and the transmitter. The solution is to use a Repeater unit. It could also be that the transmitter unit is mounted on a wall, which has a high content of metal. Or the distance between the units could be too big. Placing a Repeater unit in between the units will extend the communication distance. Maximum numbers of repeaters to one system are three. 900-1003114 Alert HyperGuard Quick pager MP10D (English V1) Page: 7/9 Date:May 31, 2013 Jumpers
** No.1
** No.2
** No.3
** No.4
** No.5
** No.6
** No.7
** No.8
** No.9
** No.10 World leader in metal detection for anti-shoplifting purposes 3.4 Repeater setup Jumper No. 1 No. 2 No. 3 No. 4 No. 5 No. 6 No. 7 No. 8 No. 9 No. 10 When the repeater is added to the Pager system do the following:
Function Programming mode (only to be used when programming) This repeater is no. X This repeater is no. X No use No use No use No use No use No use No use 1. Set the repeater in program mode by placing the jumper in No.1 2. Switch the power on
3. Make sure that the distance between the repeater and pager transmitter is more than 3 meters. 4. Press the one of the bottoms on the Pager transmitter or activate an alarm in the EAS system. If the programming is OK the TX led will flash at the same time as on the Pager transmitter 5. Switch the power off 6. VERY IMPORTANT:
Set the transmitter in normal mode Remove jumper No. 1 7. Switch the power on and test the system 8. Maximum 3 repeaters can be in a system. They must be numbered 1-2-or 3 by setting the jumpers as described above 900-1003114 Alert HyperGuard Quick pager MP10D (English V1) Page: 8/9 Date:May 31, 2013 5V via USB 89x148x26 mm 200 g 426MHz note1, 433MHz, 915MHz, ISM band 9.9mW 50 Ohm SMA 175 meters in open space 350 meters in open space Yes World leader in metal detection for anti-shoplifting purposes 4. SPECIFICATIONS Pager transmitter PT01D:
Operating voltage Dimension Weight Frequency Transmit power Antenna impedance Antenna connection Distance to receiver Distance to Repeater RoHS compliant Pager receiver QR01D:
Battery type Standby time Charge time Dimension Weight Frequency Signals Adaptor RoHS compliant Pager repeater PA01:
Operating voltage Dimension Weight Frequency Transmit power Antenna impedance Antenna connection Distance to receiver Distance to Repeater Adaptor RoHS compliant CE (433MHz), Approvals FCC/IC (915MHz) Note 1: under development. Expected in production: primo Q3 2013 Article number: 9001031114 5V via USB 89x148x26 mm 200 g 426MHz note1, 433MHz, 915MHz, ISM band 9.9mW 50 Ohm SMA 175 meters in open space 350 meters in open space 100-240Vac Yes 2.4V, 400mAh NiMH rechargeable 24 hours 10 hours 47x96x23 mm 100 g 426MHz note1, 433MHz, 915MHz, ISM band Light, beep or vibration 100-240Vac Yes 900-1003114 Alert HyperGuard Quick pager MP10D (English V1) Page: 9/9 Date:May 31, 2013