FCC ID: E86EKOPAG Alpha-numeric 2 way alarm and paging device

EkoTek Multitone Electronics plc, Multitone House, Shortwood Copse Lane, Basingstoke, Hampshire, RG23 7NL Tel: +44 (0)1506 418198 Fax: +44 (0)1506 411711 Email: info@multitone.com Web: www.multitone.com This brochure is for guidance only. Products and services offered are subject to availability and may differ from those described or illustrated in this brochure as a result of changes. Specifications are subject to change without notice. Multitone Electronics plc is part of Kantone Holdings Ltd, a member of the Champion Technology group of companies. Registered office: Multitone Electronics plc, Shortwood Copse Lane, Kempshott, Basingstoke, Hampshire, RG23 7NL. Registered in England No. 256314. Literature No: ekotek/ds/issue 2 FM 20122 Hub The hub is the systems central control unit, displaying assistance call messages, the calling user and location. Device configuration can be changed using a PC running web browser software such as Internet Explorer. Network and device data can be collected. Pager messages, production of groups of pagers and location display allow call fob or pagers users to be located. EkoTek systems can be extended using Synchronized Ethernet Repeaters (SERs). Up to 8 SERs can be used to extend a system. Repeater Battery operated with a battery life of up to 2 years which form the mesh radio network. EkoTek Personal Security System EkoTek is a battery operated mesh network based on the 802.15.4 standard which can be easily implemented within a building without routing wires. EkoTek provides two-way communication to user devices, allowing them to raise an alarm and receive messages from team members to know help is on the way. Call Fob The call fob allows an assistance call to be generated either by the user pressing a button, or automatically by the dead-man or man-down features. Accurate location information is regularly obtained from the repeater network and relayed to teams for immediate assistance. EkoTek Pager The pager is a multi-functional device, displaying received messages with acknowledgement, plus the ability to generate an alarm from the button, snatch cord (panic), dead-man or man-down features. Its display shows alarms from other pagers and call fobs, allowing the user to accept the alarm and signal back to confirm that assistance is on its way. Two Levels of Alarm For both the EkoTek pager and fob there are two levels of alarm. Emergency Alarm:

l Red button: Single or double press raises an alarm with escalation l Man-down: On suffering a fall, an alarm is raised with escalation l Dead-man: Raises alarm if no response is received to a scheduled request (with escalation) l Snatch Alarm (pager only): Raises alarm if pager is snatched from cord Assist Alarm:

l Low priority alarm to call for assistance (no escalation) 1 System Maximums l Max no. of pagers: 127 l Max no. of devices per system: 500 (inc. pagers, fobs, repeaters and hub) External Connections (hub) l 2 x serial port: 300 9600 baud Port A: ESPA input/output TAP input/output Port B: TAP input ESPA input Note: TAP & ESPA protocols are not standardised and require tests for compatibility.

*dependent on usage Technical specification Radio Performance l Radio frequency: 2405-2480MHz l Radio channels: 16 l Channel operating mode: Fixed frequency, or frequency hopping l Maximum no. of radio channels simultaneously used per system: 16 l Radio power: 10mW l Radio coding: modulation format OQPSK DSSS IEEE 802.15.4 Electrical Specification l Hub power: AC-DC power adaptor l Hub back-up batteries: 3 x C cell NiMH rechargeable batteries l Repeater power: 2 X D cell high capacity alkaline manganese batteries l Pager power: 1 X NiMH rechargeable battery

(not replaceable) l Call fob power: 1 X NiMH rechargeable battery (not replaceable) l Mains powered repeater power: 9.5-15V DC 15mA, with proprietary rechargeable battery pack as back-up l Charging rack: AC-DC power adaptor l Call point power: 2 X D cell high capacity alkaline manganese batteries l Synchronized Ethernet Repeater: power over ethernet with a back-up of 2AA NiMH rechargeable batteries l Mains powered call point: 11 15V 25mA, with proprietary rechargeable battery pack as back-up l Battery life:

EkoTek pager: up to 2 weeks*

EkoTek fob: up to 4 weeks*

Welcome to your EkoTek Pager Quick Guide Further instructions are available from the multitone support site www.multitone.com 1. Buttons (from left to right):

Navigation keys: left arrow, down arrow, right arrow Blue button: assist alarm Red button: emergency alarm 4.

(if enabled) Emergency Alarm (red button):

l Single click or double click, depending on configuration raises emergency alarm l The alarm is sent out to the pagers/users configured by the administrator l Press and hold the button to clear the alarm l The alarm will be re-sent at an interval configured by administrator, until the alarm is cleared For further information or troubleshooting, please refer to your system administrator. 2. Turning on the device To switch the device on for the first time, place the unit in the charger and charge for a minimum of 12 hours. Otherwise press and hold the button Charging the battery The pager is fitted with an AAA Ni-Mh rechargeable battery. To charge the battery, place the device in the charger. Do NOT attempt to remove the battery. Opening the device will invalidate any warranty. Please give the device to your administrator for return to a Multitone Agent for service. 3. Raising and clearing alarms l When an alarm is raised a text message is sent to configured group of pagers l The text includes the raising devices identity, the alarm type that has been activated and the current location of the device l On clearance of an alarm, a text message is sent with the devices identity stating the alarm has been cleared 5. Assist Alarm (blue button):

l Single click raises assist alarm and automatically returns to normal state (no alarm clear necessary) l The alarm is sent out to the pagers/users configured by the administrator

(if enabled) Man-Down Alarm: If unit is tilted more than 45 degrees for longer than the configured trigger period Dead-Man Alarm: If a response is not entered to the pe-

riodic prompt Snatch Cord Alarm:If the pager is snatched, the cord disengages from the body of the pager and sends alarm 6. Receiving Messages l Upon receiving a message, the pager will sound an alert, vibrate and activate the backlight depending on profile settings and the message will be displayed l If multiple messages, use the and buttons to select l Select the button to see the available responses

(accept and reject or delete) l Use the button to scroll to the desired option l Select the button to send the response or delete l Accept responses will be sent to the user that raised the alarm to show help is on its way i

o d a R U E e h t f o 3 6 e c i t r A h t i l

. W e c n a d r o c c A n I y t i m r o f n o C f o n o i t a r a l c e D U E

C E 5 9 9 e v i t c e r i D E T T

R t n e m p u q E i l i a n m r e T n o i t a c n u m m o c e i l e T s m r o n o c t f i n e m p u q e G A P O K E e h t t a h t y t i l i i l b s n o p s e r e o s r u o r e d n u e r a c e d e w l

, r e r u t c a f u n a m e h t s A e h t h t i w e c n a d r o c c a n i

C E 5 9 9 e v i t c e r i D U E e h t f o s t n e m e r i u q e r l a i t n e s s e l e b a c i l p p a e h t l l a o t

s d r a d n a t s l i a c n h c e t i g n w o l l o f e h t d n a e v i t c e r i D e h t f o I I x e n n A f o s e r u d e c o r p l

) 2 3 e c i t r a e v i t c e r i D

8 2 3 0 0 3 N E I S T E l

b

1 3 e c i t r a e v i t c e r i D

3

9 8 4 1 0 3 N E I S T E

1

9 8 4 1 0 3 N E I S T E l

a

1 3 e c i t r a e v i t c e r i D

0 5 9 0 6 N E i r e d n u

) e c v e d e g n a r t r o h s c i f i c e p s

n o n

1 2 s s a C b u S l

, 1 s s a C s a l i t d e a n g s e d e r a s t n e m p u q e e s e h T i t e k r a M d n a t n e m s s e s s A y t i f m r o n o C n o i t i a c n u m m o c e e T

l M A C T d n a e v i t c e r i D e h t f o s m r e t e h t

. e m e h c s n o i t a c i f i s s a c

) e e l t t i m m o C e c n a l l i e v r u S n o p u r o

, m o c

. e n o t i t l

. u m w w w m o r f i t d e n a b o e b y a m y t i f m r o n o C f o n o i t l a r a c e D e h t f o y p o c l l

. e n o t i t l u M o t n o i t a c i l u f A p p a e c n a i l p m o C f o t n e m e t a t S a d a n a C y r t s u d n I

C C F

N E G S S R s d r a d n a S a d a n a C y r t s u d n t I l d n a s e u R C C F e h t f o 5 1 t r a P h t i w s e i l p m o c e c v e d s h T i i

. 0 1 2 S S R

. n o i t a r e p o d e r i s e d n u e s u a c y a m t a h t e c n e r e f r e n t i y n a t p e c c a t s u m e c v e d s h i i l f u m r a h e s u a c t o n y a m e c v e d s h i i t

) 1

s n o i t i d n o c o w t i g n w o l l o f e h t o j t t c e b u s s i n o i t a r e p O t

) 2

d n a e c n e r e f r e n t i e h t t e a r e p o o t e u n i t n o c o t t y t i r o h u a s

r e s u e h t i d o v l l i w t i n e m p u q e s h i t o t l

. s e u R 5 1 t r a P C C F d n a a d a n a C y r t s u d n I e h t f n o o e p o c s e h t n h t i i w e c v e d i i t a c i f i d o m d e s i r o h t u a n U t d e a e r t e b t l o n d u o h s t c u d o r p s h i t

, e f i l l i e b a e c v r e s s t i f o d n e e h t t A e h t o t r e v o d e d n a h e b d u o h s t I

. l e t s a w l l a r e n e g r o d o h e s u o h s a

, t n e g a r i e h t r o e n o t i t l u M o t d e n r u e r r o t

, t i n e m p u q e c n o r t c e e l i d n a l a c i r t c e e l f o g n i l c y c e r e h t r o f t i n o p n o i t c e l l o c e b a c l i l p p a

. l a s o p s d r o i f l a s o p s D i t c u d o r P

e v i t c e r i D E E E W 8 6 1 9

1 6 2 9

G A P

. o N t c u d o r P 1 e u s s i

c c

r e g a P k e T o k E

o N e r u a r e t t i L

Multitone Electronics plc EkoTek Pager Quick Guide www.multitone.com EU Declaration of Conformity In Accordance With Article 6.3 of the EU Radio &

Telecommunication Terminal Equipment R & TTE Directive 99/5/EC. As the manufacturer, we declare under our sole responsibility that the EKOPAG equipment conforms to all the applicable essential requirements of the EU Directive 99/5/EC, in accordance with the procedures of Annex II of the Directive and the following technical standards:-

ETSI EN 300 328 (Directive article 3.2);

ETSI EN 301 489-1; ETSI EN 301 489-3 (Directive article 3.1{b});

EN 60950 (Directive article 3.1{a}). These equipments are designated as Class 1, Sub Class 21 (non-specific short range device) under the terms of the Directive and TCAM (Telecommunication Conformity Assessment and Market Surveillance Committee) classification scheme. A full copy of the Declaration of Conformity may be obtained from www.multitone.com , or upon application to Multitone. FCC & Industry Canada Statement of Compliance This device complies with Part 15 of the FCC Rules and Industry Canada Standards RSS GEN & RSS210. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference that may cause undesired operation. Unauthorised modification to this equipment will void the user's authority to continue to operate the device within the scope of the Industry Canada and FCC Part 15 Rules. WEEE Directive & Product Disposal At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment, or returned to Multitone or their agent, for disposal. 9261-9210 EkoTek-Pager/QUG/Iss. 7 2 of 13 EkoTek Pager Buttons (from left to right):

Navigation keys: left arrow, down arrow, right arrow. Blue button: assist alarm. Red button: emergency alarm. Turning on the device To switch the device on for the first time, place the unit in the charger and charge for a minimum of 12 hours. Alternatively, press and hold the to turn on, after a power off. Charging the Battery The pager is fitted with a AAA Ni-MH rechargeable battery. To charge the battery, place the device in the charger, the LED will flash to acknowledge charging.

- 1 flash every 3 seconds charging.

- 2 flashes every 3 seconds charged. Do NOT attempt to remove the battery. Opening the device will invalidate any warranty. Please give the device to your administrator for return to a Multitone Agent for service. Snatch Cord The pager is supplied with a small blanking plug. If the snatch cord is not required, the blanking plug can be installed in the snatch cord socket and the feature disabled by the administrator for this device. NB Once inserted, the blanking pin cannot be removed. 9261-9210 EkoTek-Pager/QUG/Iss. 7 3 of 13 Display Status Icons The following icons are displayed in the top right corner of the display as status indicators:

Battery charge:

Plugged in to power source:

Audible alert:

Shift mode: day shift:

Screen display vibrate alert:

night shift:

11:34 AM 12.03.07 Paul Smith Training Room Name / Message status Current Location If box is empty known location.

- last 9261-9210 EkoTek-Pager/QUG/Iss. 7 4 of 13 Raising and clearing alarms When an alarm is raised a text message is sent to configured group of pagers. The text includes the raising devices identity, the alarm type that has been activated and the current location of the device. On clearance of an alarm, a text message is sent with the devices identity stating the alarm has been cleared. Upon receiving a message, the pager will sound an alert, vibrate and activate the backlight (depending on profile settings) and the message will be displayed. Emergency Alarm (red button): (if enabled) Single click or double click, (depending on configuration) raises an emergency alarm. The alarm is sent out to the pagers/users configured by the administrator. Use the button to clear the alarm. The alarm will be re-sent at an interval configured by administrator, until the alarm is cleared. Assist Alarm (blue button): (if enabled) Single click raises assist alarm and automatically returns to normal state (no alarm clear necessary). The alarm is sent out to the pagers/users configured by the administrator. Wander alarm (if enabled) Zones which are restricted, are set and configured by the administrator. Upon entering one of these restricted zones, the pager will activate a response (as configured by the administrator):

o Audible and vibrate alert o Audible alert o Vibrate alert. The message unauthorised zone will also appear on the pager screen. The alarm is sent out to the pagers/users configured by the administrator. 9261-9210 EkoTek-Pager/QUG/Iss. 7 5 of 13 Man-down alarm (if enabled) If unit is tilted more than 45 degrees for longer than the configured trigger period, then it goes into pre-alert mode. The unit will beep prior to sending the alarm; to prevent the automatic man-down alarm being sent, return the unit to the upright position. The alarm is sent out to the pagers/users configured by the administrator. To clear alarm, return to upright position and use the button to clear the alarm. Dead-Man alarm (if enabled) Unit will periodically prompt user to press one of the navigation keys (frequency is configured by the administrator.) Press the , or button to respond to the periodic check and prevent automatic alarm generation. If a response is not entered, an alarm is sent out to the pagers/users configured by the administrator. To clear a raised alarm, press and hold the button. Snatch Cord Operation (if enabled) The snatch cord should be inserted in the socket on the body of the pager. If the pager is snatched, the cord disengages from the body of the pager and an alarm is automatically sent. Re-inserting the snatch cord cancels the alarm. 9261-9210 EkoTek-Pager/QUG/Iss. 7 6 of 13 Receiving Messages Receiving a message The new message will display on the pager screen. Message actions:

o Select the button to see the available responses (accept and reject or delete). o Use the button to scroll to the desired option . o Select the button to send the response or delete the message. o Accept responses will be sent to the user that raised the alarm, to show that help is on its way. Message Overview Screen After display time-out, the screen returns to the message overview screen. The first part of each message is shown in a list format. Use the button to scroll through the messages. Use the button to display the full message. 9261-9210 EkoTek-Pager/QUG/Iss. 7 7 of 13 Status Indicators Low battery status alarm (if enabled) This alarm occurs when the battery reaches less than 25% charge. The notification is either an audible or vibrate alert (dependent on profile settings). The message re-charge battery will also appear on the pager screen. Out of network range alarm (if enabled) This alarm occurs when the pager is out of range of the EkoTek mesh network. The notification, audible or vibrate, depends on the chosen profile which can be found under the advanced menu. The message out of range will also appear on the pager screen. Although the pager will automatically search for a network to connect to, this process can also be quickened by pressing the button. 9261-9210 EkoTek-Pager/QUG/Iss. 7 8 of 13

Profile Power Off Advanced Menu Navigation From the stand-by screen:

Press and hold the button to enter the main menu:

Profile Use the button to scroll to Profile. Press the button to select this option. When selected, use the button to navigate between:

Profile Custom Custom Allows individual settings of various options such as backlight, audio and vibrate alerts and whether messages are displayed when pager is in charger. Normal Disables the custom profile menu, leaving the pager in its default state as follows: backlight enabled (single colour), audible enabled, vibrate disabled, receive on and charge disabled. Dynamic Backlight enabled (tri-colour), audible and vibrate alert enabled, receive on charge disabled. Quiet Backlight only enabled (single colour). Desk Backlight enabled (single colour), audible enabled, vibrate disabled, receive on and charge enabled. Pressing the button will confirm the selected profile; the button will leave at current setting. Power Off (if enabled by administrator) Use the button to scroll to Power Off. Press the button to select the option, the icon will turn black. Press the button again to confirm the action and the pager will turn off. Power On To power back on press the and hold to switch back on. 9261-9210 EkoTek-Pager/QUG/Iss. 7 9 of 13 3. Advanced Use the button to scroll to Advanced. Press to select the option. Use the button to scroll to the desired option:

Off Display Power save Custom profile*

Hide clear info

*if custom profile selected, otherwise this option will be blank. a) Display Off To select, press from the Advanced menu options. Hour Mode Display Timeout Font Contrast 24H 16s 10 x 5 2 For ALL the following options:

Use the button to select the option Use the button to scroll between options Use the button to select the required option Use the button to return to the display menu Use the button again to return to the main menu if desired i. Hour Mode Available options: 12H and 24H. ii. Display Time-out Available options: 8, 16, 32 and 64 second time-out. iii. Font Available options: 7 x 5, 10 x 5, 10 x 8 formats (only applicable to message display). iv. Contrast Available options: scroll between 0 to 5. 9261-9210 EkoTek-Pager/QUG/Iss. 7 10 of 13 b) Powersave from the main menu The powersave option blanks the screen after a set period, to save power. Use the to scroll to the powersave option. See 3.a) for how to navigate and select options. On

Display Power save Custom profile Hide clear info Off c) Custom Profile Use the button to scroll to Custom profile. Display Power save Custom profile Hide clear info

On Off Press to select this option, where upon the following options are displayed.

Backlight Audible alert Vibrate alert Rx on charge On On On On See 3.a) for how to navigate and select options. i. Backlight Use the button to scroll to backlight. 3 options exist for the coloured backlight and may be selected as follows:

o Off backlight is switched off o On single colour backlight is used o Tri backlight colour is co-ordinated with alerts or activity indication. See 3.a) for how to navigate and select options. ii. Audible alert To turn the audio alert on/off:

See 3.a) for how to navigate and select options iii. Vibrate Alert To turn the vibrate alert on/off:

See 3.a) for how to navigate and select options. iv. Rx on Charge To enable or disable the pager from receiving alerts when on charge:

See 3.a) for how to navigate and select options. 9261-9210 EkoTek-Pager/QUG/Iss. 7 11 of 13 d) Hide Clear Info clear a raised alarm. The clear alarm instruction can be displayed on the screen to show users how to To hide this information the Hide Clear Info function can be turned on. See 3.a) for how to navigate and select options. 9261-9210 EkoTek-Pager/QUG/Iss. 7 12 of 13 Care If dropped in water or other solution, rinse in clean water and dry the unit off. The unit is dust and water resistant to IP67. Multitone Electronics plc, Multitone House, Shortwood Copse Lane, Kempshott, Basingstoke, Hampshire, RG23 7NL Telephone: +44 (0)1256 320292 Fax: +44 (0)1256462643 Email: info@multitone.com Web: www.multitone.com This document is for guidance only. Products and services offered are subject to availability and may differ from those described or illustrated in this document as a result of changes. Specifications are subject to change without notice. Multitone Electronics plc is part of Kantone Holding Ltd, a member of the Champion Technology group of companies. Registered office: Multitone Electronics plc, Shortwood Copse Lane, Kempshott, Basingstoke, Hampshire, RG23 7NL. Registered in England & Wales No. 256314. Registered VAT No: GB 232150709. FM 20122

EkoTek System Installation and Configuration Manual Survey Installation Configuration Maintenance www.multitone.com EkoTek System Installation and Configuration Manual Table of contents Table of contents...........................................................................................................i Approvals .....................................................................................................................3 Compliance...............................................................................................................3 FCC and Industry Canada Statement of Compliance ..............................................3 WEEE Directive and Product Disposal.....................................................................3 System Overview .........................................................................................................4 1. EkoTek principles .................................................................................................5 2. Location reporting.................................................................................................6 3. Alarms ..................................................................................................................7 4. Location alarm......................................................................................................7 5. Beacons................................................................................................................7 6. Two-way acknowledgement .................................................................................7 7. Two-way radio ......................................................................................................7 8. Frequency hopping...............................................................................................8 9. ESPA and TAP paging I/O ...................................................................................8 10. Configuration ......................................................................................................8 11. Network parameters ...........................................................................................9 12. Diagnostics and statistics ...................................................................................9 Components...............................................................................................................10 1. Hub.....................................................................................................................10 2. Repeater and mains-powered repeater..............................................................10 3. Solar repeater.....................................................................................................11 4. Call point and mains-powered call point.............................................................11 5. Call fob ...............................................................................................................12 6. Pager..................................................................................................................13 7. Quad pager charging rack ..................................................................................14 Synchronised Ethernet Repeater...............................................................................15 1. Overview.............................................................................................................15 Network design and survey........................................................................................17 1. Overview.............................................................................................................17 2. Prerequisites.......................................................................................................17 3. Placement rules..................................................................................................17 4. The survey unit...................................................................................................18 5. How to survey.....................................................................................................21 Installation..................................................................................................................22 1. Preparation.........................................................................................................22 2. Installing the hub and IP slave hub.....................................................................23 3. Installing the repeater, mains powered repeater and call point ..........................24 4. Installing the solar repeater ................................................................................28 5. Installing Synchronised Ethernet Repeater (SER) .............................................30 6. Installing the PPP modem ..................................................................................31 7. Installing the four-way pager charging rack........................................................37 8. Browser interface setup......................................................................................38 9. Main menus........................................................................................................41 10. Maintenance menus .........................................................................................43 11. Configuration menus ........................................................................................47 12. SER overview ...................................................................................................49 13. Final checks......................................................................................................70 14. Configuring SERs .............................................................................................71 Synchronisation..........................................................................................................74 Appendix 1: Miscellaneous system messages...........................................................75 9261-8173 issue: 8 2012 Multitone Electronics Plc Page i EkoTek System Installation and Configuration Manual 1. Personal security messages...............................................................................75 2. Pager response messages.................................................................................75 3. Maintenance messages......................................................................................75 Appendix 2: Specifications .........................................................................................76 Appendix 3: RS232 cable pin-outs for connecting the modem to the hub .................77 Appendix 4A: Overlapping system support ................................................................78 1. Overview.............................................................................................................78 2. Overlapping and mobile roaming systems .........................................................78 Appendix 4B: Channel allocation with SER ...............................................................80 1. Overview.............................................................................................................80 Appendix 5: Remote logging protocol ........................................................................81 1. Overview of logging............................................................................................81 2. General formatting..............................................................................................81 3. Log examples .....................................................................................................83 Appendix 6: External system connections .................................................................85 Appendix 7: Over the Air upgrade..............................................................................86 Revision history and related documentation ..............................................................88 1. Revision history ..................................................................................................88 2. Related documentation.......................................................................................88 9261-8173 issue: 8 2012 Multitone Electronics Plc Page ii EkoTek System Installation and Configuration Manual Approvals Compliance This product complies with the requirements of the EU Radio & Telecommunications Terminal Equipment Directive 99/5/EC. FCC and Industry Canada Statement of Compliance This device complies with Part 15 of the FCC Rules and Industry Canada Standard RSS 210. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference that may cause undesired operation. Unauthorised modification to this equipment will void the user's authority to continue to operate the device within the scope of the Industry Canada and FCC Part 15 Rules. A full technical specification for this product may be obtained from your Multitone representative. WEEE Directive and Product Disposal At the end of its serviceable life, this product should not be treated as household or general waste. It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment, or returned to the supplier for disposal. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 3 EkoTek System Installation and Configuration Manual System Overview EkoTeks personal security system consists of mobile devices that send assistance messages to other fixed or mobile devices, where the assistance message and location of the caller are displayed:

Call Fob Pager Wireless Link Repeater Battery Powered Repeater AC Power Adaptor Hub Including Web Server Includes Personal Security Alarm Repeater Repeater Repeater to Repeater Distance Typically 10 to 15m Messages are communicated via a backbone radio network, which makes use of repeaters to relay messages around the network. Due to the multi-hop nature of the backbone network, the physical shape and size of the network is defined by the layout of the repeaters, which may be in three dimensions e.g. covering multiple floors in a building. EkoTek is truly wireless (only the hub needs AC power), making installation and expansion very quick and easy. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 4 EkoTek System Installation and Configuration Manual 1. EkoTek principles Each EkoTek product is a node that forms part of a self-organising radio mesh network:

Node Node Node Node Node Node Node Node Node Each node in the network searches for links to nearby nodes, to form the network mesh. Organising the network is an automatic function carried out by the nodes themselves configuration is not required. As the network is self-organising, it is also self-repairing. Should a node (repeater) fail, the network will automatically reconfigure around the failed node:

Node Node Node Node Node Node Node Re-route Re-route Node Node The dimensions of the network are defined by the layout and distribution of repeater nodes, the layout being arranged to meet the requirement, e.g. reception and public areas of a hospital, accident and emergency department, or all floors of a building for security guard lone-worker protection. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 5 EkoTek System Installation and Configuration Manual Sizeable networks can be easily built, due to the large number of repeaters supported by EkoTek. Repeaters are normally installed on walls and/or ceilings. By adding an enclosure they can easily be installed outdoors. The hub is installed either on a wall or on a desk, so that the display can be easily seen:

Hub Repeater Hub and Repeaters automatically form a mesh network 2. Location reporting When a user raises an alarm signal, it is important to know the location of the user to ensure that assistance arrives as quickly as possible. EkoTek provides accurate location reporting, based on location signals sent out by the repeaters:

Repeater Call Fob Location Signal 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 6 EkoTek System Installation and Configuration Manual 3. Alarms A user may manually signal an alarm by pressing the red button on a pager or call fob, or alarms may be triggered automatically for man down, dead man or location alarms. When an alarm is triggered the user identification (name), location and alarm type are included in the alarm message displayed on the hub and sent to pagers. 4. Location alarm The location alarm feature allows pagers and call fobs to automatically raise an alarm should the device wearer enter a location where the local repeater indicates an unauthorised zone. Applications include resident wander, where an alarm would be raised if a resident wandered into a zone where they were not expected or not allowed, and contractor/visitor location alarm where an alarm could be raised if a person entered a part of the building that they were not authorised to access. 5. Beacons Beacon signals are used to update a device with information of who its parent is. The hub and all repeaters regularly transmit two types of beacon system beacons and location beacons. Location beacons generally have a shorter range than System beacons. A repeater, pager or call fob can only ever have one parent at a time. Every 1000ms the repeater transmits to the pager or call fob, which is then updated with its location and will continue to receive subsequent beacons from the repeater (its parent). If the pager stays within range of the location beacon the location will be shown on the pager's display, = [location name] (for example, =

Conference Room 1). If the pager goes out of range of the location beacon but can still receive the system beacon, - [location name] will be shown instead, where

[location name] is the name of the last location beacon received. When a pager or call fob receives a new location beacon it picks up location information from the new repeater and updates itself with the new location. 6. Two-way acknowledgement Messages from external systems and maintenance messages are one-way messages from the hub to the pager, whereas alarms generated by a user are two-

way. For peace of mind of the user, the acceptance of an alarm at the hub or a pager by someone who will be coming to the aid of the user is signalled back to the user by the call fob lamp and beeper changing their alert patterns, or by the pager display indicating the status of the alarm. 7. Two-way radio All EkoTek radio links are two-way, providing the ability to signal both to and from all devices on the network. Two-way radio provides the ability to quickly detect and correct any lost messages, for example, when a message is relayed from one repeater to a second repeater, the second repeater will acknowledge receipt of the message. If the first repeater does not receive an acknowledgement it retransmits the message. This ability allows EkoTek to function, even in environments where there is radio interference or poor signal. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 7 EkoTek System Installation and Configuration Manual A further benefit of two-way radio is the ability to download configuration parameters to all devices from the hub, using over-the-air programming. Devices do not hold their own configuration, as this is sent by the hub upon request when devices are powered up. Even pagers and call fobs have their configuration held at the hub, making it unnecessary to recall mobile devices for configuration change, as all updates are made centrally at the hub. 8. Frequency hopping EkoTek radio links can be configured to operate on a fixed frequency, or to hop across all 16 available frequencies. Frequency hopping increases the immunity of EkoTek systems to radio interference. If a message is lost due to interference on a frequency, the loss is immediately detected and the message retransmitted on the next frequency in the hopping sequence. Frequency hopping is especially useful where the local radio environment may be unknown, or subject to change. EkoTeks combination of message loss detection, automatic message retransmission and frequency hopping, makes for a very robust radio infrastructure. 9. ESPA and TAP paging I/O In addition to the in-built support for EkoTek two-way pagers, the hub provides the ability to connect the EkoTek system to external systems via a one-way paging interface. This allows the EkoTek system to either receive or to send messages to a pre-existing one-way paging system. The hub paging interface can be selected from ESPA or TAP as an input or output through Port A and by using Port B TAP or ESPA input only. This allows EkoTek to be used as a paging system, e.g. for connection to a nurse call system or to send messages to a pre-existing one-way paging system. 10. Configuration All configuration of the EkoTek system is performed via web pages stored on the EkoTek hub. Access to this web server is either via the 10/100Base-T Ethernet port or using PPP via an RS232 serial port. Configuration for all devices is held on the hub and downloaded to each device at power-up. The hub defaults allow a new system to operate out-of-the-box, only requiring the location names for the repeaters and user names for the mobile devices to be entered on the hubs web server configuration page. Each device has its own unique factory set serial number for identification, but there is no factory programming of the devices. The hub configuration set for the devices during installation defines whether device options (e.g. the man down alarm) are enabled or not. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 8 EkoTek System Installation and Configuration Manual 11. Network parameters An EkoTek system controlled by a single hub is able to support up to 500 devices. See Appendix 2: Specifications (page 76) for maximum numbers for each type of device. The network radio channels can be configured using the hub web server interface, with up to 16 channels being available for simultaneous use by a single EkoTek system. The default configuration is for all EkoTek devices to use channel 15. See the Multitone document Example EkoTek System Configurations for more information on special configurations. A single EkoTek radio channel can support up to 90 repeaters, but a limitation of 70 per channel is recommended to allow for dynamic reconfiguration (silent parent swapping). The repeaters can be configured in any physical deployment, as long as each repeater is able to establish and maintain a suitably strong signal with a nearby repeater that has a path back to the hub. 12. Diagnostics and statistics Each EkoTek device collects statistics on network performance. These statistics are regularly sent to the hub and can be viewed using the web server. Failure (e.g. loss of network coverage) and battery low indications for EkoTek devices are displayed on the status screen of the web interface; these messages are also reported on the hub and/or pager displays if the option to do this is configured. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 9 1. Hub EkoTek System Installation and Configuration Manual Components The hub is the central device in the mesh network. All communications pass to and from the hub; ideally it should be installed near the physical centre of the network, but it can be located anywhere within the network. A hub display shows alarm messages in a similar way to a two-way pager. For configuration, a PC running a web browser is connected via Ethernet to the web server running on the hub. Other connections on the hub are for alarm relay contacts, external systems, web access using PPP, and power input. Internal rechargeable batteries allow the hub to function in the event of an AC power failure. For more information on front panel operation of the hub see 9621-8276 EkoTek hub user guide. 2. Repeater and mains-powered repeater Repeaters form the backbone of the self-configure radio mesh network. Each repeater automatically forms links to nearby repeaters, to allow messages to pass across the backbone. Two screws hold the repeater to the ceiling or wall. Two internal alkaline D size batteries power the repeater. The battery voltage is continuously monitored and reported to the hub and/or pagers, raising an alarm should the voltage fall below set levels, indicating that the repeater batteries require replacement. The mains powered repeater is functionally similar but provides terminals for wiring to an external low voltage DC supply and contains an internal rechargeable battery pack for battery backup in case of supply failure. Repeaters also transmit location beacon signals, which are used by the mobile devices to determine their location, which is sent when assistance messages are generated. Repeaters may form the mesh network in 3 dimensions, with repeater radio links able to pass through walls and ceilings if necessary. By default, all repeaters operate on the same radio channel as the hub. This is the default configuration used by small systems. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 10 EkoTek System Installation and Configuration Manual However, where there is a need to force repeaters to make links to other specific repeaters, (e.g. when a building-building link is required or when using Ethernet repeaters), repeaters can be configured through the hub to operate only on specific channels. Battery replacement for the repeater is quickly achieved by sliding the repeater from the backing plate and lifting out the old batteries. No tools are required for this. An optional locking screw can be inserted where necessary to help prevent tampering with the repeater, for example, where the repeater is installed in a public environment, within reach of passers by. Repeaters continually test links to adjacent repeaters, detecting link failures and automatically searching for and establishing new links should one fail. Network moves and/or expansion are achieved by moving or adding new repeaters where required, making any network changes rapid and cost effective. 3. Solar repeater The solar repeater is based on the standard repeater, with the additional functionality of power obtained from an integral solar panel with a rechargeable battery acting as a power reserve in periods of low light. It can therefore operate in full sun or shade provided that it receives enough solar radiation to charge the battery sufficiently for the unit to continue to operate in periods of low light. The solar repeater is dust and water resistant to IP65 and UV and corrosion proof, and can be mounted on a wall or pole. 4. Call point and mains-powered call point The call point allows alarms and assist calls to be raised by a red button on the front of the unit or an external closing contact input. A call point can be used to connect to equipment that has a closing contact (a simple switch such as a ceiling mounted pull cord) to signal an alarm. The assist message is configurable separately for the red button and external contact input. The call point has an internal sounder

(configurable on/off) to indicate call state. The red button can be configured as either:

9261-8173 issue: 8 2012 Multitone Electronics Plc Page 11 EkoTek System Installation and Configuration Manual 1. Disabled. 2. Single press raises alarm. 3. Double press raises alarm. A long press of the red button always clears an alarm raised by the red button or the external alarm contact. The mains powered call point is functionally similar but provides terminals for wiring to an external low voltage DC supply and contains an internal rechargeable battery pack for battery backup in case of supply failure. The call point can also be used as a repeater while still retaining call point functionality. For mounting positions where the unit is at body height this is not recommended, as the quality of link that the call point can offer will degrade when someone stands near or in front of the unit. This may cause devices communicating through the call point repeater to lose contact with the network. For high positions such as operating in conjunction with a ceiling pull cord this should not be a problem. A situation where repeater operation may be acceptable if the unit is at body height is to allow the unit to be a repeater for mobile devices only. This can be achieved by setting the call points Downstream channel to a channel that other repeaters cannot use as an Upstream channel. 5. Call fob The call fob allows assistance calls to be raised, using the location signals from repeaters for accurate location determination. The call fob also supports dead man, man down and location alarms [explained in Configuration section]. The configuration of the call fob is downloaded from the hub when the call fob is powered up. The selection of the call fob options is by hub configuration. All call fobs are physically identical and support the same features (if enabled at the hub). An LED, buzzer and vibrate motor are contained within the call fob and are used to indicate the call status. These change when a call is accepted by a remote user using the hub or a pager. Indication of assistance on its way is signalled in this way. An AAA size battery powers the call fob. Either rechargeable NiMH or disposable alkaline batteries may be used. Note that rechargeable batteries cannot be charged in the call fob; the battery will have to be removed and placed in an external charger when charging is required. For further information see 9621-8277 EkoTek call fob user guide. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 12 EkoTek System Installation and Configuration Manual 6. Pager The pager has the following key functions:

other EkoTek devices Display of and response to assistance calls from Display of paging messages created using the Raising assistance calls in a similar manner to the Snatch cord operation (later models only) hubs web server or an external system call fob For further information see 9621-8275 EkoTek pager user guide. EkoTeks two-way radio network provides message interchange between devices, for example, when a call fob raises an assistance message this is displayed on the hub and the pagers. A pager or hub user can then accept the call, which is signalled back to the call fob and indicated to the user by a change in the LED and beep pattern being emitted by the call fob during the assistance call. Paging messages can be generated either via the hub web server or an external system. Web server-originated pager messages can be configured to show delivery and request a Yes/No response (only from EkoTek pagers with this two-way paging function); simple task management systems can be easily created. In a similar way to call fobs, pagers are able to generate assistance calls using the red assistance button on the pager, the inbuilt man down or dead man functions, or location alarms. A pager can therefore function as both an alarm unit and a display, eliminating the need for users to carry both types of unit. An AAA size battery powers the pager. Either rechargeable NiMH or disposable alkaline batteries may be used. Charging contacts on the pager are used when the pager is inserted into a charging rack. Later pager models also have a snatch cord that is inserted into a socket on the body of the pager. The pager generates personal security assistance calls when the snatch cord is pulled and disconnected from the body of the pager if enabled. On these models the snatch cord can be replaced with a blanking plug if this functionality is not required. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 13 EkoTek System Installation and Configuration Manual 7. Quad pager charging rack The quad pager charging rack charges up to 4 pagers at one time in the rack, with a maximum charge times of 12 hours to charge a pager battery to 50% of its capacity. The pager reports charging in its usual status report. An extra report is generated when a pager enters or leaves the charger so the hub can update its status quickly. When a pager reports its battery status as charging, this is shown on the device status display. Man down and dead man alarms are automatically disabled when a pager is inserted into the charging rack. When a pager is installed in a charging rack, a user-

configurable feature allows the pager to be set to receive or ignore messages, allowing the pager to continue to function in the charging rack if required. The standard EkoTek PSU is used as the rack PSU and can be used to power up to two charging racks. Note: The pager must be fitted with a NiMH rechargeable cell when used in a charging rack. Use of the charging rack with other types of cell may damage the pager. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 14 EkoTek System Installation and Configuration Manual Synchronised Ethernet Repeater The Synchronised Ethernet Repeater may simply be thought of as a repeater that connects through the customers LAN. 1. Overview The Synchronised Ethernet Repeater (SER), acts in the same way as a normal repeater. It provides radio coverage and location information in a similar manner to a standard repeater. However, the most important aspect of the Ethernet Repeater is that it provides synchronous radio coverage over potentially wide areas. The SER is a powerful new way to obtain synchronised radio coverage across large installations. The upstream is connected to the hub via the LAN rather than as a radio link in the standard repeater. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 15 EkoTek System Installation and Configuration Manual The synchronous aspect should not be overlooked nor misunderstood this is probably the most significant aspect of the SER. When correctly configured, synchronised radio coverage is crucially important and supports the following functionality in EkoTek installations:

1. Replaces long chains of repeaters - linking between buildings would previously have required chains of repeaters to be set up. 2. Provides robust and reliable radio coverage more effective in multi-floor environments because the radio path back to the hub is via LAN. 3. Up to 8 SERs can be connected to a single hub with one SER being master for system timing. 4. Allows the EkoTek hub to be remotely located on the customers LAN previously required to be at the centre of the network coverage but can now be located in a Security Control Centre in a remote location. 5. Provides synchronised radio timing with other SER via the LAN. 6. Without synchronisation fixed networks could possibly interfere with each other and mobile devices will not necessarily detect new networks. Note: A stable and reliable customer LAN is essential when using SERs in the System. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 16 EkoTek System Installation and Configuration Manual Network design and survey 1. Overview The survey is used to assess the number of repeaters required and best locations. It is suggested that the surveyor reads the System Overview section (page 4) to become familiar with the basic principles of operation. 2. Prerequisites Two survey pagers (2WSU) Site plan 3. Placement rules Each repeater connects to the hub, either directly or via another repeater. The number of repeaters required depends on the size and layout of the building and the consistency of the radio coverage. The EkoTek hub and repeaters must not be installed in areas where explosive gas or dust products may be present. Devices must be protected from liquids, extreme temperatures and strong magnetic fields. Do not install in places where they will be exposed to strong sunlight or electromagnetic interference. Hub The hub should be placed in an area such as a control room or reception desk where it is possible to monitor the display when required. Other considerations are to minimise the number of hops required for any repeater to connect to the hub; it is better if possible that the hub be located at the centre of the network, unless using SERs. The hub must be located near an AC mains socket outlet and an Ethernet connection; it should also be borne in mind that connection via a modem link to the telephone network may be needed, so access to a telephone socket would also be necessary. It is important that there are multiple repeaters around the hub to ensure multiple paths to the rest of the network and overcome any possible people blocking of the hub. Repeaters Ideally repeaters should be spaced 10-15 metres apart. They should be no closer together than 6 metres, except where there is a structural barrier sufficient to attenuate the radio signal, such as a wall between repeaters. The maximum range is 20 metres, but placing repeaters at this distance should be avoided if possible, as any degradation of the radio path may result in the loss of connection between repeaters. For the positioning of a solar repeater see Solar repeater positioning (page 28). Multi-storey buildings EkoTek can be used in multi-storey buildings, where the floors are of concrete construction. The concrete floor provides sufficient attenuation of the radio signal to ensure that the pager or call fobs location is reported on the correct floor. In wooden floored buildings, the pager may pick up a beacon from the 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 17 EkoTek System Installation and Configuration Manual floor above or below, giving an inaccurate location for the device. Careful positioning of repeaters is therefore required when wooden or mezzanine floors are in use if location is important. In order to establish which floor the pager or call fob is on, it is important that repeaters are placed at the entrances to the bottom and top of stairwells. The actual placement of the repeater may not necessarily be in the stairwell itself, but may be in a room leading to the stairwell, in order to provide sufficient radio separation between repeaters. Corridors In long corridors it may be prudent to place a repeater in the middle of the corridor as well as at the ends, to ensure robust radio connection in the mesh. Room placements If locating in individual rooms, place the repeater as central to the room as practical. Placing it on the edge of the room may allow sufficient strength of location signal to pass through the wall to be seen as a beacon by a pager or call fob in the adjacent room or corridor. It is however highly unlikely that the signal would pass through more than one wall. In large rooms such as warehouses, it will be necessary to place more than one repeater to ensure adequate radio coverage. Between buildings If buildings are sufficiently close together, radio signals may pass between them. However, if for example a vehicle passes between the buildings, it may cause signal deterioration and the repeater to lose contact with its parent. For this reason on a multi-storey building, it would be better to force the repeaters on the first floor to form the link between buildings. This is achieved by setting the downstream link of the parent on the first floor of one building to be a specific channel and the upstream link of the repeater on the first floor of the adjacent building to be also the same channel (unless using SERs). Mesh structure A repeater can only have one parent at a time; however, the principle of a mesh network is that if a connection fails the repeater can search for an alternative parent in order to rejoin the network. If it is unable to locate a suitable new parent, its portion of the network will be broken. It is therefore important to ensure that any repeater has multiple potential paths to the hub. 4. The survey unit The survey unit is designed to assist in the placement of repeaters and aid in trouble

-shooting the network. It has several modes of operation, described below. The buttons scroll through the menus. A long press on the button will switch the survey pager on and off. When taking measurements always hold the pager by the left hand side to avoid masking the signal; the pagers antenna is located on the right hand side. Also avoid placing your body between the pager and the measured device, as this will attenuate the signal. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 18 EkoTek System Installation and Configuration Manual Note: The survey pager is continuously transmitting a signal and its battery life is therefore short. To avoid unnecessarily draining the battery, switch off and/or remove the battery when not in use. Survey pager modes RSSI This screen indicates the signal strength for each channel in both the Rx and Tx paths. The measurement for each channel is displayed as a vertically stacked number. Ideally the RSSI should be 30 or above. Quality This screen indicates the quality for each channel in both the Rx and Tx paths. The measurement for each channel is displayed as a vertically stacked number. The range of reported values is 0 to 99 with 99 being the best quality. Ideally the quality should be 90 or above. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 19 EkoTek System Installation and Configuration Manual Network monitoring mode Channel activity This shows the activity on each channel and is useful in determining the amount of Wi-Fi activity on the system. Note: Channel activity can take some time to be detected, so run for at least 1 minute. Repeater information This screen shows information about the repeater that the survey pager is connected to. The bar display shows the strength of the repeaters beacon received by the survey pager relative to the programmed repeater location range. The RSSI number is an indication of the signal strength of the repeaters parent as received at the repeater. Out of range location beacon This screen displays information about nearby repeaters. The bar display shows the strength relative to the programmed repeater location range. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 20 EkoTek System Installation and Configuration Manual 5. How to survey Decide on the location for the hub. It is desirable to mount the first repeater close to the hub location since radio transmissions can be affected by people close by. Ask the customer which locations are critical for accurate call location reporting and mark on the plan those places as locations for repeaters. It may be every room, a defined area or different floors. In very large rooms use more than one repeater. Also mark on the plan the positions for repeaters at the top and bottom of all stairwells, to allow location tracking between floors. The customer may also want to have a location change when persons leave a critical area. If so, mark repeaters on the site plan at the exit of those critical areas. When all the likely places for repeaters have been marked, inspect the site plan to estimate if the distance between repeaters exceeds the 10-15 metre maximum separation rule. If there appears to be a long gap between repeaters, consider if there are repeaters on the floor above or below that can form a path for the network. If a repeater appears to be isolated, use survey pagers to check the RSSI. Place a pager at the repeater and measure the RSSI at its nearest neighbour. Remember its nearest neighbour may be on a different floor. If the nearest neighbour is the other side of a thick wall, other marked locations may provide a more viable route. If in doubt it is best to place in-fill repeaters, as the more repeaters in a network the more robust the network is liable to be. If the RSSI is below 20, then consider placing another repeater in between. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 21 EkoTek System Installation and Configuration Manual Installation 1. Preparation Prerequisites Prior to installation, the following items are needed:

Site plans with position of the hub and all the repeaters clearly marked An AC mains socket outlet for the hub An Ethernet connection to the customer LAN for the hub A working telephone line and AC mains socket for the PPP connection

(if required) A line for external ESPA or TAP system connection (if required) Identify which PC is to be used for admin access and log file downloads If installing SERs they will need an AC mains socket outlet plus connection to the customers LAN Tools recommended Pozidriv screwdriver Screwdriver with 2.5mm blade Stepladder Cordless drill 5mm masonry bit 6mm masonry bit Metric rule Laptop with Ethernet port Ethernet patch cable Call fob and pager from customer system Survey pager Equipment required EkoTek hub with AC power supply unit If modem access to a telephone link is required then use current recommended modem with AC supply unit and a RS232 (proprietary) connecting lead. See Appendix 3: RS232 cable pin-outs for connecting the modem to the hub EkoTek repeaters: quantity as required by survey. It is also suggested that spare repeater/s are supplied, in case there is a need for infill that was not detected on the survey (Ethernet repeater/s as required) 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 22 EkoTek System Installation and Configuration Manual 2. Installing the hub and IP slave hub The hub can be freestanding on a desk, or wall mounted using the screws provided. To remove the cover, depress the two protruding plastic tabs and separate the top from the back plate. Wall mounting Mark the position of the screws on the wall. The two screws should be spaced precisely 120mm apart, as shown in the diagram of the back plate below:

120mm Drill two holes with a 5mm masonry bit to a depth of 25mm. Insert the wall plugs and screw the screws. Leave 7mm of the screw protruding. (Note: Screws and plugs not provided). Locate the screw heads in the holes in the back-plate and pull the unit down to lock into place. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 23 EkoTek System Installation and Configuration Manual Interface connections Port A -

(DB9) Port B -

(DB9) Plug in the AC to DC power adapter provided with the hub. Plug in the Ethernet patch lead to connect to the LAN or PC. See Connecting the hub to the PC using Windows XP (page 41). If an external alarm is to be activated from the hub, connect a pair of wires from the alarm output shown in the interface connections diagram. The alarm output is a simple make/break contact and can be used to operate a customer provided alarm relay. This is not designed to provide a direct contact for AC mains operated equipment. Connect the DB9 port A connections to the customer's paging system if required. The connection cable should be as specified by the paging system. A PPP connection can be made after the modem has been set up via port B. See Installing the PPP modem (page 31) for further details. 3. Installing the repeater, mains powered repeater and call point Mounting the repeater or call point (incl. mains powered variants) Remove the back plate from the device by removing screw A and sliding the top and the base in opposite directions as shown by the green arrows. The standard repeater is shown in the diagram; the call point and mains powered devices are opened in the same way. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 24 EkoTek System Installation and Configuration Manual When mounting the mains powered devices it may be easiest to detach the power cable from the circuit board first by gently pulling out the connector from the board. The mains powered repeater/call point may be supplied with the power cable already detached. Use the back plate to mark the position of the screw holes on the wall or ceiling. The call point may be mounted at desk height but if it is also to be used as a repeater it should be mounted using the same criteria as a normal repeater. The contact for the call point should then be extended to a switch

(such as a ceiling pull switch). 44m m If fixing to masonry, drill two holes with 6mm masonry bit to a minimum depth of 30mm and insert wall plugs. Screw the back plate in position making sure the screws are left flush to back plate. When installing a mains powered repeater, refer to Wiring the mains powered repeater/call point. If installing a call point that needs to be wired to an external switch, refer to Wiring the call point to an external switch. After installation, lock the devices (if required) by screwing the small screw provided in the installation parts, as indicated by A in the picture on previous page. Wiring the mains powered repeater/call point Note:

1. The mains powered repeater requires a DC supply between 9.5v and 15v at 2. The mains powered call point requires a DC supply between 11v and 15v at 15mA. 25mA. 3. When wiring several repeaters in a chain it is important to specify the system power supply and cabling so that the power supply voltage at the repeaters at the beginning and end of the chain are within these limits, taking into account cable resistance. It is advisable to check these voltages with a meter after installation has been completed. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 25 EkoTek System Installation and Configuration Manual Create an exit point for the wires from the mains powered repeater by removing the section indicated in the illustration below with a pair of pliers. Break away case here to create exit point for wires. Turn on the mains powered device by removing the link from the repeater PCB. Wire the supply leads to the device using the screw terminals in the connecting block. Note: Be careful to observe the correct polarity as shown on the label. Connection block. Observe polarity. Remove this link and turn through 90 degs to be able to use to disable battery in future Remove this connector if desired while fitting the base plate. Remember to reconnect it to complete the installation. Before sliding the mains powered device back on to the base plate, offer the device up to the base plate and plug the power connector into the circuit board. Ensure the batteries are in place then slide the device on to the base plate. Take care not to snag the power cable. Wiring the call point to an external switch The call point may be wired to an external switch if alarms are to be initiated from a location that is remote from the call point. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 26 EkoTek System Installation and Configuration Manual Create an exit point for the wires from the call point to the external switch by removing the section indicated in the illustration below with a pair of pliers. Break away case here to create exit point for wires. A pre-wired header is provided with the call point and this should be attached paying particular attention to forming the wires as shown below to avoid snagging them when sliding the unit on to the back plate. Place wires as shown here. The header is wired as follows:

Pin 1 = External alarm activate. Pin 2 = Ground (for both contacts). Pin 3 = External alarm cancel. Connecting this input to the ground pin has the same effect as a long press on the front button of the call point, clearing any alarm that the call point has raised. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 27 EkoTek System Installation and Configuration Manual 4. Installing the solar repeater Solar repeater positioning The repeater should generally be sited with the solar panel facing the sun at its zenith. It must have at average of at least 30 minutes a day of sunlight shining on the solar panel even in the winter months (note: that snow and ice covering the repeater for long periods may cause problems). The normal annual maximum and minimum temperatures must be within the range -20C to

+35C, although brief periods outside this range will probably not result in failure. Solar insolation (solar radiation received at the earth's surface) maps can be used to help determine an areas suitability. Near the equator, temperature may be more important than hours of sunshine and facing the solar repeater east so that the unit is not in direct sunlight in the hottest part of the day may be best. The repeater should be sited so that there are no obstructions causing the solar panel to be shielded from the sun at any time during the year. For example, in London, England (latitude 51.5N) the sun only reaches 15 above the horizon on the shortest day of the year, so the ideal location will be facing south with no obstruction more than 15 above the horizon. Use of a compass is recommended. The solar repeater comes with the batteries pre-installed and must be mounted in a vertical position since the unit has been designed to be switched off when lying on its side. The solar repeater is distributed with two fixing kits, one designed for wall mounting and one designed for pole mounting. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 28 EkoTek System Installation and Configuration Manual Wall mounting The solar panel is fixed to a wall using screw fixing brackets that are attached to the repeater as shown below:

Insert screw fixing brackets into the slots on the back of the solar panel. Pole mounting The solar panel is fixed to the pole using a nylon strap (not provided with the repeater) that passes around the pole and through fixing brackets that are attached to the repeater as shown below:

Nylon strap passes through the bracket. Insert strap fixing brackets into the slots on the back of the solar panel. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 29 EkoTek System Installation and Configuration Manual 5. Installing Synchronised Ethernet Repeater (SER) The SER can be installed either by wall-mounting (recommended) or placed on a non-metallic surface. It must be within the vicinity of AC mains supply and Ethernet connection. If wall mounting then turn the unit over and measure the distance between the mounting holes and using the tools previously mentioned drill two holes for mounting. 90mm Note: The SER product design may change in future releases. Read EkoTek SER user guide before configuring SERs. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 30 EkoTek System Installation and Configuration Manual 6. Installing the PPP modem Connecting the modem The PPP connection (port B) to the hub is made using a US robotics 5630D modem. 1. Plug the modem into the serial port of a PC using the serial interface cable provided with the modem. Use an adapter if the PC does not have a serial port. (See Appendix 3: RS232 cable pin-outs for connecting the modem to the hub (page 81) for details of cable pin-outs). 2. Install the US Robotics software onto the PC, from the CD provided with the 3. After installation, locate the software in the programs menu on the PC and modem. start. The software automatically detects if the modem is connected. Click the configuration manager and go to the call control tab. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 31 EkoTek System Installation and Configuration Manual Set the Number of rings to answer call box to 1. Click the Save to modem button, which stores the current values from the configuration manager's fields to the writable memory of the modem. Go to the DTE interface tab and set the DTR to ignore DTR. Using Windows Hyper Terminal to set the interface speed A terminal program is an application that will enable a PC to communicate directly with a modem. If you are using Windows 2000 or Windows XP, you can use the Windows HyperTerminal program as it is included as part of the operating system. 1. Check that the modem is connected to a serial port on the PC. 2. Load HyperTerminal:

Click Start > Run 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 32 EkoTek System Installation and Configuration Manual In the box which appears, type HYPERTRM Click OK If you see the error message 'Cannot find HYPERTRM' you will need to install HyperTerminal:

Click Start > Settings > Control Panel > Add / Remove Programs. In Add / Remove Programs select Properties and then click the Windows Setup tab Double-click Communications Check the box for HyperTerminal Click OK, and then OK again to install Note: You may be asked for your Windows installation disk for this procedure 3. When Hyper Terminal starts you will be presented with a 'Connection description' dialogue box. Click 'Cancel' to continue 4. Select the preferred COM port:

Select 'File' then 'Properties' from the menu bar and the 'New connection properties' window will open Click on the arrow for the 'Connect using' drop down box Select 'Direct to ComX' (where X is the COM port you are using to connect the modem - e.g. COM1, or COM5, etc) Click OK 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 33 EkoTek System Installation and Configuration Manual 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 34 EkoTek System Installation and Configuration Manual Configure the port to set the interface speed to 57600 5. Click OK - a blank terminal window will open. You should now be communicating directly between the COM port and modem. Type 'AT' [enter]

If you are communicating, the modem will reply with 'OK'. If so, proceed to step 6. If no 'AT' or 'OK' appears, then there is a basic communication issue between the PC and the modem - most likely the COM port selected is incorrect - check this and try again. If problems persist:

Check Windows Device Manager (where available) Check that the modem is installed Check the COM port is enabled and has no clashes (indicated by a yellow exclamation mark next to it) Check the COM port is enabled in the system BIOS setup 6. To store the configuration of the port speed in the modem, type 'AT&B2&W'

[enter]. You should receive 'OK' as a response. 7. Remove the lead from the PC COM port and connect to Port B on the hub. 8. Close the cover on the hub. Ensure that the ribbon for the keypad is connected to the header on the daughter board, as this is sometimes dislodged when the cover is removed. 9. Test by dialling in to the modem from a PC. The user name and passwords are both EkoTek. The modem should auto answer and the EkoTek menu screen should be displayed. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 35 EkoTek System Installation and Configuration Manual Set up system configuration using the browser as described in the 8. Browser interface section. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 36 EkoTek System Installation and Configuration Manual 7. Installing the four-way pager charging rack Up to 2 four-way charging racks may be supplied from the PSU. Wall mounting Measure and drill the wall according to the diagram: on next page If two units are used, join together using the nylon screws and nuts provided as shown below:

Warning label Fix the warning label close to the rack where it is easily visible. RECHARGEABLE CELLS ONLY 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 37 EkoTek System Installation and Configuration Manual IDC connections Remove or cut off the power jack from the end of the PSU lead. Bare the ends and connect to the IDC connector in the first rack. Ensure the polarity is correct, (+ve black with the white stripe) as shown in the diagram above. Loop the supply through to the second rack if fitted, and terminate as shown in the diagram below. 2 1

2 1

+ve Black/White

-ve Black 8. Browser interface setup Initial setup In order to configure the system a PC or a network Ethernet connection needs to be made to the hub. This connection can also be used to monitor the EkoTek network. Once the connection has been made, then communication with the hub is achieved through a web browser. Port A -

(DB9) Port B -

(DB9) Connecting the hub to the PC using Windows XP On the PC:

1. Click the Windows start menu and select Control Panel. 2. Click Network and Internet connections. 3. Click Network Connections. With the network cable disconnected, the Local Area connection will be shown as unplugged (X). 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 38 EkoTek System Installation and Configuration Manual 4. Open the hub. To open the hub, push the two locking tabs in and then separate the cover from the back plate. 5. Connect an Ethernet (RJ45) patch cable to the RJ45 connector - see the hub interfaces diagram. 6. Connect the other end of the patch cable to the Ethernet (RJ45) connector on the PC. Note: Some network cards require a crossover cable for direct connection. If connected correctly the screen will change to show the cable connected. 7. 8. Double click the Local Area Connection icon to open the properties window. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 39 EkoTek System Installation and Configuration Manual 9. Scroll the new window and select the Internet Protocol TCP/IP menu item. 10. Click the Properties button. 11. The default shipped configuration for the hub is:

192.168.1.2 (1.1.1.1 if via PPP serial port) IP address:

Subnet mask:

255.255.0.0 Default gateway: 192.168.1.20 In order to communicate between the PC and the hub, the IP address of the PC has to be set to the same network and subnet as the hub. To achieve this select Use the following IP addresses and enter the IP address in the same range as the hub (in the example above 192.168.1.100 and a subnet mask of 255.255.0.0 Gateway 192.168.1.20). 12. Click OK to finish. Using the web browser to access the hub In the address field of the web browser, type the IP address of the hub (default is 192.168.1.2 for Ethernet) and click the refresh button. The browser then connects to the hub web interface. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 40 EkoTek System Installation and Configuration Manual Password When a configuration menu item is opened at the beginning of a session, a password is requested. The default is user name admin with no password

(blank). Once access is gained the password can be set as required. In addition, user name user (blank password) gives access to Main and Maintenance menu items, and Passwords and Browser language selection under the Configuration menu. admin 9. Main menus Note: The mains powered devices appear to the system to be identical to a regular repeater or call point. Wherever a reference to a repeater or call point is seen this also applies equally to the mains powered variants. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 41 EkoTek System Installation and Configuration Manual Day/night Use to set the shift mode. This can be used in conjunction with alert rules to route alarms to different target groups. Event log The event log keeps track of all events on the system. It records:

The time and date for each event recorded The type of event and the text of the associated message For each of the applications the following events are recorded:

PS = personal security: Alarms raised, accepted and cleared PG = paging application: Pager messages sent, delivery report if requested, any user responses if requested MT = maintenance: devices not reporting status or low battery warnings these messages are also sent to pager group one (1) 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 42 EkoTek System Installation and Configuration Manual The event log stores the last 9000 events in flash memory. Once 9000 events have been recorded, any new event received is stored and the earliest recorded event is removed from the log. Page device Paging messages can be sent from this screen to all EkoTek pagers, pager groups (select group from drop list) or individual pagers (select pager from drop list). Two-way pager messages for user responses may be requested for pager groups or individual pagers, and delivery of messages to individual pagers may be logged. Pager log The pager log stores the last 15 pager messages that had either Log message delivery or Request user response ticked. Messages are kept until the 16th new message with response or delivery request ticked, or if hub is reset.

"Enter message here Note: The pager messages are also written into the event log. Location If location reporting for mobile devices has been enabled under the device mode, the location screen shows the last location reported by each mobile device. If a device does not have location reporting enabled Not enabled will appear in place of the location report time and location. If a device has not reported its location since the hub has powered up it will display Unknown. 10. Maintenance menus Device status 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 43 EkoTek System Installation and Configuration Manual Each device in the mesh connects to the hub via a parent device (repeater or directly to the hub itself). Maintaining this connection is important. These statistics relate to that connection. Status reports are made every 4 hr 33 min 4 sec. Device statuses in the list are highlighted as follows:

Low battery = yellow Replace battery = red Missed status report = yellow Missed four consecutive status reports = red Device status - hub and IP slave hub Hub: Serial number. Name: Name given to the hub. Hardware - software: revision number. Last report: Time and date stamp of last report. Battery level: For the hub this will always be 100% when running on mains power. Battery level (%) will be indicated when on backup power. Upstream link: This will always be Direct connection. It is the topmost link of the network. Beacon loss count: This count records beacons lost since startup or reset. Parent sync loss: Number of times that a loss of sync has occurred since startup or reset. Link quality: general quality of link to the hub, 1 to 100 where 100=best. Direct connection is always 100. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 44 EkoTek System Installation and Configuration Manual Link strength: RSSI of parent link, 1 to 100 where 100=best. Direct connection is always 100. Upstream traffic: Count of packets sent to parent. The loss counts and upstream traffic are simple incrementing counters. Device status - repeater, solar repeater and call point If no status report has been received these will show

Awaiting status report Unknown All other fields will be blank. Repeater, solar repeater or call point: Serial number. Battery level: Shows the battery level. An alarm is given when battery level drops to 20% and a replace battery message initiated at 5%. Upstream link: Name and serial number of parent repeater or hub. Beacon loss count: Missed parent beacons. This counts the number of times the beacon was expected but not received, either through a faulty parent or degradation of the signal to the parent. Parent sync loss: Number of times that a loss of sync with parent has occurred. Other fields are the same as for the hub. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 45 EkoTek System Installation and Configuration Manual Device status - call fob and pager Pager or fob: Serial number. Name: Name given to device. Hardware - software: revision number. Last report: Time and date stamp of last report. Battery level: Shows the battery level (%) or Charging if the battery is being charged. Beacon loss count: Missed parent beacons. This counts the number of times the call fob or pager has lost contact with its parent either, through faulty parent or degradation of the signal through moving out of range of the repeaters. Parent sync loss: number of times that a loss of sync with parent has occurred. Request update: Click to retrieve current statistics. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 46 EkoTek System Installation and Configuration Manual Tree View Parent 030-0005137 Child 030-0005103

<n> = Number of requests for Config [n] =

RSSI Level The network tree is used to try to provide information relevant to the fixed devices in the system. Information provided includes:

Number of times a device requests its Config from hub o A high number may indicate the need for additional repeaters to overcome poor radio connections The RRSI level (as indicated above) o A high number shows a good link but a low number does not necessarily mean a poor link (it is for the last status report only and conditions /parent selections change) The linkage paths between devices o This chain length to a given repeater is the number of I symbols in front of it Identifies parent and child relationship The parent can be identified from the child by identifying the (+) and tracking upwards to the (<n>). The number of (I) indicates the number of hops from the hub. This can lead to an unstable network with poor connections. 11. Configuration menus System settings - hub This page sets the network interfaces. It enables configuration of hub settings, clock, external connections and the browser language. Click Configuration and select System. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 47 EkoTek System Installation and Configuration Manual Set clock The clock operates in two modes, one displaying the current time (if JavaScript is enabled on the browser this will update, if not then the clock is a snapshot of the time the page was loaded). 1. Click the details button and enter the current time and date. 2. Click Submit to set. Note: An illegal clock setting will return to clock display mode, but the original settings will be retained. Set date format The hub allows either of two date formats to be selected:

Day/Month/Year displayed as 05.01.12 Month/Day/Year displayed as 01.05.12 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 48 EkoTek System Installation and Configuration Manual The date format applies to the hub/pager displays and the hub web server pages showing logs, location and maintenance information. To change the date format click the submit button. This will change the date format to that shown on the button. The button then changes to show the other format. For example, a screen similar to the above will be seen if the date is set to Day/Month/Year format and clicking the Submit mm/dd format button will change the display to Month/Day/Year. Hub IP configuration If the hub is to be connected to an Ethernet network the IP address, subnet mask and gateway should be set within the address range of the network, to allow the hub to be accessed from the network. In general the port should be left at the default value, (6113), unless this port is being used for another application on the network. Once the IP address is configured the hub can only be accessed using that IP address, so a note should be made of any IP address that is set. If the address of a hub is unknown it can be obtained from the front panel. See the EkoTek hub user guide 9261-8276 for details. Note: An illegal IP setting will return to the system settings screen and the original settings will be retained. Remote system connection For setting up the connection to an external system, such as a paging or nurse call system. Refer to Appendix 6 External system connections (page 85) for details of remote system configuration. Remote logging 1. Click Remote event logging to allow system event messages be sent to a remote logging machine. 2. Select Numeric, Text or both depending on the required output. 3. Click Remote debug logging to forward all received/transmitted messages to remote machine. 4. Set the IP address of remote logging machine of the remote computer. Click Submit to set the new external connection settings. Logging messages are always sent to UDP port 514. Note: No check is made that the remote logging machine exists. For more details of the event logging protocol see Appendix 4B: Channel allocation with SER 1. Overview The SERs is used in a customer network to provide synchronised radio coverage over a larger site without having to resort to separate or overlapping systems. The repeater 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 49 EkoTek System Installation and Configuration Manual operates in a similar way to a normal repeater except for the fact it is linked back to the hub via the customers LAN. Each SER is allocated its own channels to operate in its own area and link with the other repeaters in its vicinity, because it is linked back via the LAN it does not need to be able to reach back to the hub via the radio path. This helps to reduce long chains of repeaters across a larger site and means set channels can be used in different areas of a large site. This helps to ensure a stable radio network. Linking between buildings can be done using SERs via LAN where before a chain of repeaters would have been required (this helps by reducing the overall device count on the system). With complex network setups advice should always be sought from Multitone Customer Services for assistance when planning this type of installation. Appendix 5: Remote logging protocol (page 85). Language The browser interface is available in multiple language variants and it is therefore important to ensure you have the correct version installed for your customer. Select the required language from the drop list and click Submit. System settings IP slave hub This page sets the network interfaces for the slave hub and the browser language. Click Configuration and select System. Slave The IP address, subnet mask and gateway should be set within the address range of the network, to allow the hub to be accessed from the network. Once the IP address is configured, then the slave hub can only be accessed using that IP address, so a note should be made of any IP address that is set. If the address of a hub is unknown it can be obtained from the front panel. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 50 EkoTek System Installation and Configuration Manual Click Submit to save the slave hub settings. Hub IP address: Enter the IP address of the main system hub. Port: Set the port to that set in the system settings for the main hub. Click Submit to save the main hub settings. Radio settings Network identifier The network identifier enables mobile devices to differentiate between EkoTek systems. Depending on its configuration the mobile device may ignore a different system (if configured to lock to a single network identifier) or attempt to log on to any system. The mobile device will get its configuration from the system it is logged on to. For a mobile device to successfully move between systems it must be able to detect the change, so each system it is to operate on must have a different network identifier. Note: Overlapping EkoTek networks are supported from release 3.0 onwards. See Appendix 4A: Overlapping system support (page 82) for further details. Delay optimisation Inbound is used for maximum speed of delivery in the direction towards the hub and is normally only used when there are no pagers on the network, i.e. no outbound user messaging. This is useful if external paging is intended as the main method of alerting users. Balanced is used where there are EkoTek pagers on the system, to give a balanced speed of message flow across the radio network, both towards and from the hub. Balanced is fine for most applications and is the default. Frequency hopping The 2.4GHz band has 16 channels. Frequency hopping allows the radio to change frequency (hop) between different channels in the band. This helps the 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 51 EkoTek System Installation and Configuration Manual system avoid interference from Wi-Fi devices using the spectrum and offers more security from eavesdropping, if this is a consideration. The system can also be set to use a fixed frequency. Usually only the first 14 channels are used for Wi-Fi systems and setting to use a single fixed frequency in channels 15 or 16 could prove to be more robust where there is heavy Wi-Fi usage. Set to On (frequency hopping enabled) or Off if not required. By default the hub is configured to the fixed frequency option (Off). By selecting On and submitting, the following screen will be shown. This allows you to select which channels to use to frequency hop with. This allows that any local Wi-Fi operating channels can be de-selected and therefore reducing the interference by using only clean channels to hop through. Device auto-register If device auto-register is set to On, any unknown device that is detected is permitted to join the network provided that the device limits have not been exceeded. These devices will be given default names. If the auto-register is set to Off, devices need to be manually added to the database before they will be recognised as on the system. New devices are set to default to:

Default name User group 1 Fixed device zone 1 Device mode 1 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 52 EkoTek System Installation and Configuration Manual Any devices with a display will be added to the first pager group if capacity exists. Mobile device monitor All fixed devices are automatically monitored for battery condition and presence on the network, with maintenance messages generated on low battery or absence of the device from the network; these messages are sent to all users in pager group 1. Mobile devices (pagers and call fobs) can also be monitored for battery condition and presence on the network. Set to Off, Battery or Network+Battery as required. Note: The battery condition will be displayed on the Device status page, regardless of this setting. Radio language The pager display language is available in English, Francais, Espanol, Deutsch, Svenska or Norsk. Select required language from the drop list and click Submit. Auto-register names With the device auto-register set to On, when the network detects a device it gives a default name appropriate to the device type: HUB, IP SLAVE, REPEATER, SOLAR REPEATER, CALL POINT, PAGER or FOB. This default name can be redefined if required. Select device from the drop list and click Details. Enter a new name for the default and click Submit to set. For example, this sequence could be used to set all pagers to register by default as Staff and all call fobs as Visitor. Devices The devices page lists ALL the devices connected in the EkoTek network when ALL is selected. Refresh To get the current list of devices, select the hardware type to be listed from the drop list and click the Refresh button. The devices will then be listed;

9261-8173 issue: 8 2012 Multitone Electronics Plc Page 53 EkoTek System Installation and Configuration Manual 1. The first column gives the hardware type and serial number of the device. 2. The second column gives the device name. 3. The third provides a Details - button, to go to that specific devices record. The serial number of each device is displayed and the device name. 001-xxxxxxx indicates a hub. 002-xxxxxxx indicates a IP slave hub 004-xxxxxxx indicates an Ethernet Repeater 010-xxxxxxx indicates a call fob 020-xxxxxxx indicates a pager 030-xxxxxxx indicates a repeater 031-xxxxxxx indicates a solar repeater 040-xxxxxxx indicates a call point Click the Details button to see the device configuration. Add Click Add at the bottom of the displayed list to go to the Select device new entry pages. 1. Select device type from menu. 2. Enter serial box and enter the serial number and name. The entry screen below is for a repeater. Similar screens are shown for other device types, with the appropriate hardware code displayed. 3. Click Add to add the new device. If the entry is valid the individual device entry page will then be displayed. If entry is not possible (invalid serial number length, attempt to add a device prior to the hub, attempt to add a second hub, too many devices already on-system, etc.) then Invalid device request will be displayed. If a device exists in the database with the same serial number as the new requested device, the existing device details will be displayed. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 54 EkoTek System Installation and Configuration Manual Details Hub, IP slave hub and call point Name The name of the hub or call point may be changed, by entering a new name in the box. Device mode The hub or call point is allocated a device mode (1-32), with 1 as default. However, the name for each device mode can be user configured, in which case different options will appear in this menu. The device mode defines the behaviours of all similar devices (radio channel, alarm raising ability, etc). See the Device mode section (page60). User group Select from the drop list, to set User Group (1-16). Used to route alarms to different pager groups. Zone Fixed devices are allocated a zone number, allowing alarms from mobile devices to be sent to different pager groups based on the hub or repeater (and therefore zone) that the mobile device is connected to, and for directly raising location alarms. Up to 16 zones are supported by the EkoTek system. After selecting the device mode parameters, click Submit to enter the changes. Repeater and solar repeater Name The name of the repeater may be changed, by entering a new name in the box. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 55 EkoTek System Installation and Configuration Manual Device mode Each repeater is allocated a device mode (1-32), with 1 as default. However, the name for each device mode can be user configured, in which case different options will appear in this menu. The device mode defines the behaviours of hubs (radio channel, alarm raising ability, etc). Zone Fixed devices are allocated a zone number, allowing alarms from mobile devices to be sent to different pager groups based on the hub or repeater (and therefore zone) that the mobile device is connected to, and for directly raising location alarms. Up to 16 zones are supported by the EkoTek system. After selecting the device mode parameters, click Submit to enter the changes. Pager and call fob Name The name of the pager or call fob may be changed, by entering a new name in the box. Device mode Each pager and call fob is allocated a device mode. The device mode defines the alarms and location reporting. See the Device mode section (page 60). User group Select from the drop list, to set User Group (1-16). Used to route alarms to different pager groups. After selecting the device mode parameters, click Submit to enter the changes. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 56 EkoTek System Installation and Configuration Manual Device mode This section allows changes to be made to device parameters. The initial page presents a list of the different hardware types. A drop down menu allows selection of a specific device mode for the hardware type (by default these are 1-32, but they can be renamed) and a Details button, which goes to the specific hardware device mode page. Device mode hub and IP slave hub The hardware type is followed by the modifiable device mode name (default is 1-32). Channel Select from the drop down menu (1 -> 16) to set the radio channel to be used by the hub. The default value of 15 should be used where possible. Different channels should be used for each hub when installing overlapping systems. See Appendix 4A: Overlapping system support (page 82). Location range Defines the range of the location signal from the hub. The default value is 2 which gives an approximate range in indoor environments of 3 metres. A value of 1 gives the shortest range and 10 the longest range. The range should not 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 57 EkoTek System Installation and Configuration Manual be set to high values in deployments where location signal penetration through walls and floors is not desired. Manual alarm enable Sets whether the hub can raise manual alarms, i.e. by pressing the button. Alert text Modify text to define the message sent to pagers when the alarm is activated. The default text is Assist. Operation Define how many button presses are required to trigger the manual alarm (1 or 2) selected by drop-down menu. Select either Single click or Double click. Alarm audible alert Define whether device buzzer sounds when manual alarm is raised. Dead man alarm enabled Enable the dead man automatic alarm. This is raised if no input is received from the user when prompted by the device. Alert text Modify text to define the message sent to pagers when this alarm is activated. The default text is No response. Timer interval Sets the time (minutes) between user input prompts. User alert period Sets the length of time (seconds) that the buzzer sounds on the hub after the user input prompt before the alarm is raised. If the user presses a button during this time the alarm is not raised. Alarm clearance alert text Modifiable text appears in the message sent to pagers when any alarm for this device is cleared. The default text is Cleared. Alarm escalation period If an active alarm is not cleared within this period of time (minutes), then the device resends the alarm with an alternate escalation level. After selecting the above parameters, click Submit to enter the changes. Device mode repeater and solar repeater 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 58 EkoTek System Installation and Configuration Manual The device mode entry page shows the hardware type, followed by the modifiable device mode name (defaults 1-32). Lock to network With Overlapping System Support (OSS), the repeaters must be locked to a network if there are overlapping systems. To lock to a network check the Lock to network box. It is advised that Lock to network should not be checked for single standalone systems, and should not be checked for an overlapping system until all devices have joined the network. For more details see Appendix 4A: Overlapping system support (page 78). Upstream channel/downstream channel This applies to repeaters, solar repeaters and call points only. It is used to determine the radio channel (1-16) of the repeater, selected via drop down menu. In addition, the As parent setting allows a repeater to use the same radio channel as its parent device. This is the default mode of operation, allowing for a self-organising radio network. Location range Defines the range of the location signal from the repeater. The default value is 2 which gives an approximate range in indoor environments of 3m. A value of 1 gives the shortest range and 10 the longest range. The range should not be set to high values in deployments where location signal penetration through walls and floors is not desired. After selecting the above parameters, click Submit to enter the changes. Device mode - call point The device mode entry page shows the hardware type, followed by the modifiable device mode name (defaults 1-32). 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 59 EkoTek System Installation and Configuration Manual Lock to network, upstream channel, downstream channel and location range These are set in the same way as for the standard repeater. Repeater If this is set, the call point acts as a repeater as well. Manual alarm enable Sets whether the hub can raise manual alarms, i.e. by pressing the red button. Alert text Modify text to define the message sent to pagers when the alarm is activated. Default text is Assist. Operation Define how many button presses are required to trigger the manual alarm (1 or 2) selected by drop-down menu. Select either Single click or Double click. Alarm audible alert If enabled, the device buzzer sounds when manual alarm is raised:

Single pips raising alarm Double pips raised alarm (the hub has sent out an alarm message) Triple pips alarm accepted by a pager user Contact Input Alert text Modify text to define the message sent to pagers when the alarm is activated. The default is Red button. Operation This sets the criteria for the operation of the alarm. Changeover - pull cords that have a contact that changes state each time the cord is pulled Momentary - a momentary change of state on the 'raise' line input will cause an alarm to be raised (e.g. contact open-closed-open, or closed-

open-closed). A second momentary change of state on the line will cause the alarm to be cleared. The alarm can also be cleared using the clear line or a long red button press. Really intended for connection to devices that automatically raise and clear alarms Switched - switch type input e.g. a thermostat Latched a momentary change of state on the 'raise' line input will cause an alarm to be raised (e.g. contact open-closed-open, or closed-open-

closed). Any further change of state will have no action. The alarm must be explicitly cleared by the clear line or red button. Allows the call point to be used in nurse call or other situations where there is a risk of repeated switch activation (ie. a patient repeatedly pulling on an emergency pull cord) Alarm escalation enabled If the Alarm escalation enable option is not selected, the call point will raise the alarm only once and the audible alarm indication on the call point will cancel after 30 seconds. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 60 EkoTek System Installation and Configuration Manual This is useful for non-critical alarms where the hassle of clearing the alarm outweighs the benefits of repeating alarms with escalation. When the audible alarm indication cancels after 30 seconds a Cleared message is not sent. When the audible alarm indication ends the alarm can be raised again. Alarm escalation period If an active alarm is not cleared within this period of time (minutes), the device resends the alarm with an alternate escalation level. Device mode - pager and call fob 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 61 EkoTek System Installation and Configuration Manual The device mode entry page shows the hardware type, followed by the modifiable device mode name (defaults 1-32). The device mode entry page content for the pager and the call fob are the same except for Snatch cord enable and its corresponding alarm text, which are not present for call fobs. Lock to network If the pager or call fob is to be used exclusively on a single network then the Lock to network should be checked. See Appendix 4A: Overlapping system support (page 31). Manual alarm enable Sets whether the pager or call fob can raise manual alarms, i.e. by pressing the button. Alert Modify text to define the message sent to pagers when the alarm is activated. Defaults to Assist. Operation Define how many button presses are required to trigger the manual alarm (1 or 2) selected by drop-down menu. Select either Single click or Double click. Alarm audible alert Define whether device buzzer sounds when manual alarm is raised. Alarm vibrate alert Defines whether the vibrate motor is activated when a manual alarm is raised. Dead man alarm enabled Enable the dead man automatic alarm. This is raised if no input is received from the user when prompted by the device. Alert text Modify text to define the message sent to pagers when this alarm is activated. The default text is No response. Timer interval Sets the time (minutes) between user input prompts being requested. User alert period This feature sets the length of time (seconds) that the buzzer sounds on the hub after the user input prompt. If no entry from User then the alarm is raised, if the user presses a button during this time then the alarm is not raised. Man down alarm enable Enable the tip-over switch automatic alarm. This is raised if the unit has been moved away from an upright position for a defined period of time. Alert text Modifiable text appears in the message sent to pagers when this alarm is activated. Default text is Man over. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 62 EkoTek System Installation and Configuration Manual Tip-over trigger period Length of time a device must be moved away from upright, until the user warning buzzer sounds (seconds). User alert period Length of time that the buzzer sounds on the device, without it being returned to the upright position and the cancel button pressed, before the alarm is raised

(seconds). Snatch cord For pagers fitted with a snatch cord (later models only). Snatch cord enabled When enabled, the user will raise an alarm whenever the snatch cord on a pager fitted with this device is removed. The alarm will be automatically cleared when the snatch cord is reattached. Note: For earlier pager models without the snatch cord option, or where the blanking plug is used instead of the snatch cord, this feature should always be disabled. Alert text Modifiable text appears in the message sent to pagers when this alarm is activated. Default text is Snatched. Location alarm enabled Enable the location-based alarm. This is raised if the unit is moved to an area covered by repeaters assigned to an unauthorised zone. Check the box to enable this feature. Enter the text to be displayed when the alarm is triggered. Location audible alert / vibrate alert The mobile device beeper and vibrate functions can be enabled or disabled when the alarm is raised, allowing either covert or normal alarm operation. Check boxes to enable alert. Report in zones To select those zones where the alarm is to be raised, check the box associated with that zone. If the pager or call fob enters an unauthorised

(checked) zone the location alarm will be raised. The location alarm will be cancelled automatically if the pager or call fob re-enters an authorised

(unchecked) zone. Alarm clearance alert text Modifiable text appears in the message sent to pagers when any alarm for this device is cleared. The default text is Cleared. Alarm escalation period If an active alarm is not cleared within this period of time (minutes), then the device resends the alarm with an alternate escalation level. After selecting the above parameters, click Submit to enter the changes. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 63 EkoTek System Installation and Configuration Manual Pager groups These pages are used to manage hubs and display pagers into groups. Devices may appear in none, one or many pager groups. Each group is restricted to 35 devices. Pager group selection page The list of 32 pager groups is given in a drop-down menu. By default these are named 1-32. Each group can be assigned a name if required, using the pager group entry page. Click Details to open the pager group entry page and set up a group. Pager group entry page Pager group Enter text for the pager group name. All the connected display equipped devices are listed (by name) and a checkbox denoting membership to this group. Check the box to add the devices to the group. External pager If connection is to be made to an external pager, enter the pager identifier into the number field. This is the identifier sent via the ESPA/TAP output interface. Check the box to add the external pager to the group. Click Submit to confirm the new pager group membership. If more than 35 devices are selected the changes will not be accepted. Alert rules The alert rules determine the target pager group for every alarm. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 64 EkoTek System Installation and Configuration Manual Alarms are routed according to the user group of the device raising the alert, the location of the device when the alarm is raised (given by the zone of the local repeater), the day-night setting of the system and whether it is an initial alarm or an escalation of an existing alarm. By default, no rules are defined and all alarms raised on-system will result in messages being sent to display devices (and the external pager number) in the pager group ONE. The page operates in a number of modes, displaying the current rules table, allowing new rules to be added and existing rules to be modified and deleted. Creating alert rules ensures the right device is called at the right time instead of only sending everything to PG.1. If any rules have been entered a table is displayed, the top row of which contains:

User group Parameters set in the device entry. Groups 1 to 16. Zone Parameters set in the device entry. Zones 1 to 16. Time The day or night setting of the system. D=day, N=night. Esc The escalation level of the alarm. R=raised, N=normal. A black square means that a particular group, zone, time of day or escalation has been included in the rule. The end of the row is a button containing the name of the pager group that is targeted by the rule. If there are more than 16 rules in the table, the header will be repeated after the last rule. Edit mapping Clicking the pager group name button at the end of the row causes the page to be reloaded with modifiable rules; the selected rule will appear as a shaded row and in place of the pager group name a Remove button will appear. The checkboxes are preloaded with the current rules settings. Change the rule settings as required and then click Submit to save the amendments. Note: the EkoTek system can only send one paging message to an external system as a result of an alarm being raised. If a combination of rules is entered that would cause more than one message to be sent to an external system a conflict is detected and the Submit entry will be ignored until the conflict is resolved. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 65 EkoTek System Installation and Configuration Manual The following can be entered in the editing screen:

User group Select the user group(s) always routed by this rule. Zone Select the zone(s) routed by this rule. Time of day Select the day and/or night settings of the shift mode. Escalation The escalation level of the alarm. R=raised, N=normal Pager group Select the target pager group. EkoTek pagers only When a rule has the EkoTek pagers only option selected, messages using this rule will not be sent to an external system. Rules with this option set are shown as a shaded row in the alert mapping table, otherwise they are shown in white. If EkoTek pagers only is checked, a specified alarm event can be routed to multiple pager groups, i.e. duplicate rules may be created allowing multiple pager groups to be sent a message. In this mode external pagers will not be contacted, so there is no conflict checking across alert maps. Remove Click the Remove button to remove that rule from the table. Add Click the Add button to enter a brand new rule; note that this option will only appear if there are currently fewer than 32 rules. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 66 EkoTek System Installation and Configuration Manual Clicking the Add button will present a screen very similar to the edit rule mode;

the initial line is Enter new rule details followed by the options and (clear) checkboxes as for the editing screen. Click Submit to save the amendments. The new entry is checked for conflicts in the same manner as in the editing screen. After a successful submission the alert mapping page shows the new rule added to the list. Example alert mapping table The above example contains 3 rules:

1. The first rule routes all normal level alarms raised by devices with user group 2, in zones 1,2 or 3, with the system running in Day mode to pager group Day. 2. The second rule routes all normal level alarms raised by devices with user group 2, in zones 1,2 or 3, with the system running in Night mode to pager group Night. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 67 EkoTek System Installation and Configuration Manual 3. The third rule routes all escalated alarms raised by devices with user group 2, in zones 1,2 or 3, to pager group Staff (the light grey highlight denotes that only EkoTek pagers will be contacted in the group). All other alarms will be routed by (default) to pager group 1. Factory reset Click the Factory reset button to return the network to factory settings (all devices deleted, IP addresses, passwords reset, etc). Delete all devices Click the Clear database button to clear the database of all network devices, but leave passwords, IP addresses, etc. as before. Passwords Change the system passwords. User followed by a drop-down menu containing:

User The User level allows access to all pages within the main and maintenance menus and to the passwords page under the configuration menu (it can only change the password for user). Admin The admin level allows access to all functions. New password Enter new password in the text input box. Click Submit to enter the new password. User/admin password changed or Password change failed will be displayed, according to the outcome. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 68 EkoTek System Installation and Configuration Manual A password change failure may also be accompanied by: New password must be between 4 and 8 characters long if the password length is invalid, or You do not have permission to change this password if the user is logged in as user and is attempting to change the admin password Archive This page is used to manage archiving and restoring the system configuration. Download current configuration to archive file Click the Download button. In the File download pop-up box, click save and save the file to a location on the PC. Upload saved archive Click the Browse button and locate the saved archive. Click the Upload button and the configuration from the selected file is transferred to the hub. This will take a few minutes. If there is a failure to upload a saved configuration, this will result in the display of the following message: Error encountered uploading requested file. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 69 EkoTek System Installation and Configuration Manual If a valid configuration has been uploaded to the hub, the following text is displayed: Use archive settings (will cause a hub reset and erase current settings). The archived settings will not be applied until the hub is reset. Click the reset button to change the hub configuration to the archived settings. The process will take a few minutes, and is indicated by the normal separator in the time field on the hub LCD screen being replaced by a flashing exclamation mark. At this stage, trying to navigate within the EkoTek web pages can interrupt the reset irreversibly. To avoid having to begin the upload process again from the start, ensure that you monitor the hub LCD screen: when the normal time separator returns, the process has completed. At this point the web browser can be redirected to the new IP address of the hub. 13. Final checks Connect a PC/Laptop to the hub via the customers Ethernet LAN connection. Open the device status in the maintenance menu. Check that all the repeaters are seen by the hub. If a repeater is not seen it may:

Be out of reach of a parent Be faulty Have a flat or disconnected battery Investigate the cause using a survey pager. In cases where it is too far from the nearest repeater to get a viable link a repeater may be needed to infill and complete the mesh. Click the details for each repeater and check the strength and quality of the link. If the link looks marginal, remove the parent of that repeater from the network and see if it will change to a different parent with a better link. Seeing all repeaters may take some time with a large system. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 70 EkoTek System Installation and Configuration Manual Register a pager and a call fob using auto-register and see if an alarm from the call fob is received at the pager and that the response is sent to the fob on the network. This will check correct configuration of alert rules and groups This completes the installation. 14. Configuring SERs Connecting to SER The SER is connected to the hub via the customers LAN network using standard CAT5 cable with an RJ45 connector. The SER is shown using a PoE injector supplied as standard. (This LAN must be a solid guaranteed reliable connection). 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 71 EkoTek System Installation and Configuration Manual SER web pages To configure the SER need access to the SER web pages. This is done using any standard web browser such as Internet Explorer or Firefox. Open up the browser and type in the default IP address (192.168.1.3). This will need to be changed as all SERs must have a unique IP address within the customer range of IP addresses. SER home page When the IP address is typed into browser the SER opens at home page and immediately youre prompted for password. (Default blank). Select Submit and the following menu will be presented:

Configure SER IP address Select the IP settings option and enter an address provided by the customer to match their LAN Network, including mask and gateway settings. IP settings must be consistent with HUB IP settings. Once details entered press the Submit button 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 72 EkoTek System Installation and Configuration Manual Setting HUB IP address on SER

Select EkoTek hub and then add the HUBs IP address. The SER needs this address in order for it to communicate with the hub. Note The port number being used by the hub must be entered here (i.e 6113 in this example). EkoTek hub - (system)

* Confirm settings in EkoTek hub match those shown in the SER.

9261-8173 issue: 8 2012 Multitone Electronics Plc Page 73 EkoTek System Installation and Configuration Manual Synchronisation In a non-SER EkoTek system then the hub provides synchronisation clock to all the radio elements in the system. When SERs are added then one of the SERs will become the system synchronisation MASTER and the remaining SERs will be set as Slaves. There can only be one Master on any system. Select synchronisation on one SER only to be the Master and all others will be slave. For the Master SER the Master IP address can either be set to its own address

(10.1.101.154 in example) or (0.0.0.0). For the Slave SERs the Master IP address must be set to the Master IP,

(10.1.101.54 in example). Note:

1. The timing port is set to 6114 by default this normally works for most systems but you need to confirm with customers IT department to make sure this port is not used in their network. 2. The radio must be switched off at the hub when using SERs to provide synchronisation for system. Note: radio unchecked 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 74 EkoTek System Installation and Configuration Manual Appendix 1: Miscellaneous system messages The following on-system messages are generated in addition to alert texts configured using the web server interface. 1. Personal security messages Accepted Generated as a consequence of a pager accepting a raised alarm. 2. Pager response messages Delivered Accepted Rejected Denoting the delivery acknowledgement and appropriate user acceptance or rejection. 3. Maintenance messages Low battery Generated when the battery level drops to 20%, will be re-generated for every further 3% drop Replace battery Generated at 5% battery level and regenerated for every further drop. Maintenance required If a fixed device fails to report its status as scheduled on 4 consecutive occasions (each report sent at 4.5 hour intervals) and if the device remains persistently not reporting its status (i.e. a further 6 consecutive missed status reports), a Maintenance required message is generated. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 75 EkoTek System Installation and Configuration Manual Appendix 2: Specifications Radio frequency Radio channels Channel operating mode Maximum number of radio channels simultaneously used per system Radio power Radio coding Hub power Hub backup batteries Repeater power Pager power Call fob power Solar repeater power Mains powered repeater power Charging rack Call point Mains powered call point Maximum number of repeaters per radio channels Maximum number of pagers Maximum number of pagers in a pager group Maximum number of devices per system 2405 2480MHz 16 Fixed frequency, or frequency hopping 16 10mW CDMA IEEE 802.15.4 AC-DC power adaptor 3 x C cell NiMH rechargeable batteries 2 x D cell high capacity alkaline manganese batteries 1 x AAA cell high capacity alkaline manganese, or NiMH rechargeable battery 1 x AAA cell high capacity alkaline manganese, or NiMH rechargeable battery Proprietary battery pack 9.5-15V DC 15mA, with proprietary rechargeable battery pack as backup AC-DC power adaptor 2 x D cell high capacity alkaline manganese batteries 11 15v 25mA , with proprietary rechargeable battery pack as backup 90 127 35 500 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 76 EkoTek System Installation and Configuration Manual Appendix 3: RS232 cable pin-outs for connecting the modem to the hub DB25 2 3 4 5 6**

7 8 DCE TXD RXD RTS CTS DSR GND CD DB9 3 2 7 8 6 5 1

**not connected Transmitted data Received data Request to send Clear to send Data set ready Signal ground Rec. line signal detector Link 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 77 EkoTek System Installation and Configuration Manual Appendix 4A: Overlapping system support 1. Overview With complex network setups advice should always be sought from Multitone Customer Services for assistance when planning this type of Installation. Overlapping System Support (OSS) allows the mesh network radio footprint of multiple hubs to overlap. This may be necessary, for example, where different departments of an organisation have their own independent overlapping EkoTek systems, or where there are fringe radio areas where the networks of multiple hubs overlap. Each network needs to be set with different network identifiers and radio channels. Frequency hopping is forbidden with OSS. 2. Overlapping and mobile roaming systems Two possible configurations for overlapping systems are supported. A. Overlapping networks, where two networks substantially overlap at the same location. This could be used to provide exclusive networks within the same area each with its own population of pagers and call fobs. Overlapping networks Network B Network A B. Mobile roaming networks, where pagers and call fobs roam between the two networks. In order that pagers and call fobs hand over upon entry to an adjacent network it is important to design the networks to have minimum overlap to give a clear indication of the zone where the pager or call fob is located. This also 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 78 EkoTek System Installation and Configuration Manual ensures that pagers and call fobs have time to lose contact with their existing network and join their new network as they move between networks. Mobile roaming networks Minimum Overlap Network A Network B 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 79 EkoTek System Installation and Configuration Manual Appendix 4B: Channel allocation with SER 1. Overview The SERs is used in a customer network to provide synchronised radio coverage over a larger site without having to resort to separate or overlapping systems. The repeater operates in a similar way to a normal repeater except for the fact it is linked back to the hub via the customers LAN. Each SER is allocated its own channels to operate in its own area and link with the other repeaters in its vicinity, because it is linked back via the LAN it does not need to be able to reach back to the hub via the radio path. This helps to reduce long chains of repeaters across a larger site and means set channels can be used in different areas of a large site. This helps to ensure a stable radio network. Linking between buildings can be done using SERs via LAN where before a chain of repeaters would have been required (this helps by reducing the overall device count on the system). With complex network setups advice should always be sought from Multitone Customer Services for assistance when planning this type of installation. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 80 EkoTek System Installation and Configuration Manual Appendix 5: Remote logging protocol 1. Overview of logging The remote logging facility can be used for real time recording and remote storage of system events. Third parties are able to make use of the hubs remote logging output and external system input as a low level RS232 paging interface with higher level application software creating more sophisticated functions. For example, an application could be created to page staff members closest to the location where a request for assistance is made from, or to display the location of an individual on a graphical site plan, or to send an SMS message when a location alarm is raised. The logging output from the hub supports output of the following message types:

Paging messages Output each time a paging message is sent or responded to. Location report Output each time a device with location reporting enabled changes location. Personal security alarm Output when PS alarms are raised/cleared. Maintenance message Output when maintenance messages are raised e.g. low battery alarms from repeaters. Remote logging information is sent within a payload of SysLog formatted messages. It is sent to UDP port 514 of the IP address specified on the system configuration page. No check is made to ensure that the machine is present. Remote debug logging The hub also supports low-level message debug logging. This can be used by Multitone for the diagnosis of network problems, but in a standard running system should be set to Off. In order to differentiate between debug and event logging different SysLog levels are used. Event logging is priority info and debug logging is priority debug. 2. General formatting Remote logging messages can be set to numeric only, text only or a combination of numeric and text. These combinations allow the output to be easily human or machine readable as required. Tabs delimit the fields. All fields are present in all messages, even if empty, unless no more fields are to be filled in, where the line is then newline terminated. Message always terminated by newline. Output can be off, numeric, text or numeric and text. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 81 EkoTek System Installation and Configuration Manual Logging protocol format 1 2 3 4 5 6 7 8 9 10 Field no Type Name Log type Message type Numeric r i Reason code P m a r y h a r d w a r e P r i m a r y s e r i a l n o Primary name Text Secondary Name Message S e c o n d a r y s e r i a l n o S e c o n d a r y h a r d w a r e 1 Raised 2 Accepted 3 Rejected 4 Cleared 1 (PS) Personal security 1 Dead man 2 Man down 3 Manual 4 Location 5 Snatch cord 2 (LO) Location NA 1 3 (MT) Maintenance Low battery 2 Replace battery 3 Maintenance required NA NA NA NA Location of device raising alarm Device raising/

clearing alarm OR device accepting/

rejecting alarm Personal security alert text Device reporting its location Location Device requiring maintenance NA Maintenance message 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 82 EkoTek System Installation and Configuration Manual Logging protocol format Field no 1 2 3 4 5 6 7 8 9 10 P r i m a r y h a r d w a r e Name Log type Message type Reason code Type Numeric 1 No response required 2 Delivery report required 3 User response required 4 Delivery report & user response required 5 Externally generated message NA 1 Accept 2 Reject 1 Message 4 (PG) Paging 2 Delivery report 3 Message response S e c o n d a r y h a r d w a r e Primary name Secondary name Message S e c o n d a r y s e r i a l n o Text Blank for broadcast, or NA NA pager group name, NA or individual pager name Message text /

delivery report /

user response P r i m a r y s e r i a l n o Individually addressed destination pager/

responding pager or 0,0 for broadcast or 0,pager group number for pager group 3. Log examples Key: Green: all SysLog messages; yellow: numeric output selected; blue: Text output selected. PS: Call fob raising manual alarm at reception repeater. 1 1 3 01 0 10000 39 030 00450 96 Call fob 1 Reception Assist Note: The numbers in columns 4 to 7 are example serial number data. These will be repeated throughout, but are omitted for clarity. PS: Pager accepting (manual) alarm raised by call fob. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 83 EkoTek System Installation and Configuration Manual 2 3 01 0 10000 39 020 00983 54 Call fob 1 Pager 1 Accepted 1 LO: Pager moving within range of hub. 02 0 00983 54 001 00230 76 Pager 1 The hub 1 MT: Repeater not reporting status. 1 03 0 00450 96 Reception Maintenance required 3 PG: Message to all pagers, no response request. 1 1 0 0 4 PG: Message to pager group 1, response requested. 1 3 0 1 4 PG: Delivery report from pager. 2 03 0 00450 96 4 PG: Accept response from pager. 3 1 03 0 00450 96 4 PG: Reject response from pager. 4 3 2 03 0 00450 96 Group 1 Pager 1 Pager 1 Pager 1 The message sent The message sent Delivered Accepted Rejected 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 84 EkoTek System Installation and Configuration Manual Appendix 6: External system connections If the hubs external system interface is to be used, a link is connected to the serial port. The data rate should be set to the link speed (options are 300, 600, 1200, 2400, 4800 and 9600 bits per second). The data format and flow control should be set to match that of the receiving device (options are 7 bit even parity or 8 bit no parity with 1 or 2 stop bits). Messages will be truncated to 138 characters for TAP messages and 128 characters for ESPA messages. Only a single selection from those below can be made on the hub; bidirectional paging operation has limited support by using Port A for Output and Port B as an Input. Options are: port A ESPA input (maximum 138 characters). Note that 128 characters are defined by ESPA output (maximum 101 characters, because only alarms are sent via this interface). Note that 128 characters are defined by the standard TAP input (maximum 138 characters) TAP output (maximum 101 characters, because only alarms are sent via this the standard interface) Options are: Port B ESPA input (maximum 138 characters). Note that 128 characters are defined by the standard TAP input (maximum 138 characters) Incoming pager messages are addressed as follows:

0 = all pagers 1-32 = pager group HHHNNNNNNN for individual pagers where HHH = hardware type and NNNNNNN =

serial number. Note: ESPA and TAP protocols do not have standardised third party implementations a test with third party equipment is necessary. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 85 EkoTek System Installation and Configuration Manual Appendix 7: Over the Air upgrade Overview From release v3.08 it became possible to upgrade all non-display devices Over the Air (OTA). This is only available for non-display devices which include repeater, call point, fob, solar repeater and the mains variants. A software image for each variant is uploaded to the hub and this is then broadcast from the hub. The process takes approximately 3 hours to deliver the update and the devices reset to activate the new software at their next report time (approx. 4.5 hour period). An upgrade page was added to the configuration section to allow the Over the Air download function to be used. Upgrade Process Before commencing a download it is important to check the battery level of the devices to be updated. If the battery level is below 10% then the device will ignore an update. If the battery is between 10 - 25% the update will be collected but not become active until the battery is replaced. Above 25% and the update will become active as explained above, this is to ensure the device does not lose power in the middle of an upgrade. If this were to happen it would then need a manual upgrade to recover. From the web browser select Configuration -> Upgrade It will then be necessary to browse to where the update file has been stored on your PC/Laptop or USB stick. (ie) 040_R18.ota, current files for a call point. Having selected this file the next step is to click on Upload and wait for the file to be uploaded to the hub. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 86 EkoTek System Installation and Configuration Manual The Go button will appear and identify which device the software is for once the software is loaded on the hub, Now click on Go and the upgrade to fob devices in this example will commence. As the upload commences OTA the following screen will appear:

The Go button has been replaced by a Stop button. Clicking on this button will stop the OTA download of this file. The hub will send the update during quiet periods. Time therefore to update will depend on the size of the file but equally on how busy the system is. Typically for a Repeater it will take about 3 hrs to download OTA. When it is downloading the upgrade page shows a Stop button. When the download is completed the page will show a Go on the button again. When a device has received an update it does not activate it immediately but waits until its next scheduled report time. The report times are staggered so there is no sudden rush of messages at one instant in time. This will also help reduce disruption to the system, as devices drop off to update software before rejoining, keeping it to a minimum. This means in a large system from the start of a repeater download to the last repeater switching over to new software this time could be about 7.5 hrs. This process needs to be done for each type of non-display device on the system that needs to be updated. You can start the next device type when the current one says Go on the upgrade button. (About 3hrs between devices). A successful upgrade can be checked by selecting Maintenance -> Device Status ->

Device -> Details screen. 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 87 EkoTek System Installation and Configuration Manual Revision history and related documentation 1. Revision history Issue 1 2 3 4 5 6 7 8 Date June 2007 30.08.07 January 2008 July 2008 August 2008 18.06.09 03.11.09 13.01.12 Author M Windett R Robertson M Windett M Windett D Neale Gooding D Neale D.Simpson Revision Initial Document Production Issue Update for System Release 3 Sub Release 1 Update for System Release 3 Sub Release 2 Corrections and addition of new products Latest Base and revise the drill diameter Added mains powered repeater Review Document & Update 2. Related documentation Title EkoTek Pager User Guide EkoTek Hub User Guide EkoTek Call Fob User Guide EkoTek Call Fob Quick Instructions EkoTek Pager Quick Instructions EkoTek Hub Help Files (HTML) Part Number 9261-8275 9261-8276 9261-8277 9261-8311 9261-8312 4761-8313 Multitone Electronics plc Multitone House Shortwood Copse Lane Kempshott Basingstoke Hampshire RG23 7NL, UK Document number: 9261-8173 9261-8173 issue: 8 2012 Multitone Electronics Plc Page 88