FCC ID: A6GC4D-4MUSV8 Telematic embedded system

C4D-4MUSAA_V8 - INSTALLATION GUIDE V 1.3 18/03/2021 Table of contents Preface ...................................................................................................................................3 Warnings and notices ............................................................................................................3 FCC Regulations ........................................................................................................... 3 FCC RF Exposure Information (SAR) ............................................................................. 4 1. Hardware features .............................................................................................................5 2. Hardware description ........................................................................................................6 2.1 External view ................................................................................................................6 2.2 Internal view ................................................................................................................6 2.3 OBD connector pin out ...............................................................................................7 2.4 OBD adapter wires ......................................................................................................7 3. Preparing/installing the device ..........................................................................................8 3.1 Open the device ..........................................................................................................8 3.2 Insert the SIM card .................................................................................................... 10 3.3 Properly close the device ........................................................................................... 11 3.4 Install the OBD Dongle ............................................................................................. 13 4. LED sequences................................................................................................................. 14 5. Support ............................................................................................................................ 14 Preface The information contained in this installation guide is subject to changes in order to improve the reliability, design or features without prior notice. MUNIC Car Data reserves the right to make changes in the content without obligation to notify any person or organisation of such changes or improvements. MUNIC Car Data can in no event be held liable for technical or editorial errors or omissions herein, nor for incidental, special or consequential damages from the furnishing, performance or use of this installation guide. Please contact our technical support for current updates and supplemental information concerning the use and operation of this or other MUNIC Car Data products. Warnings and notices The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. Please read the installation guidelines, as well as the safety and operating instructions before operating your device. Follow all instructions and heed all warnings in the installation guide. There is a risk of explosion if the battery is replaced by a wrong battery type. Please discard empty battery according to local regulations. Dispose of used batteries according to the instructions. FCC Regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. FCC RF Exposure Information (SAR) This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency

(RF) energy set by the Federal Communications Commission of the United States. During SAR testing, this device is set to transmit at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The exposure standard for wireless employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. The FCC has granted an Equipment Authorization for this model device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this model device is on file with the FCC and can be found under the Display Grant section of www.fcc.gov/oet/ea/fccid after searching on FCC ID: A6GC4D-4MUSV8. For this device, the highest reported SAR value for usage near the body is 1.11 W/kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. 1. Hardware features OBD Dongle Performance Power supply Communication Positioning Interface & Telematics features Environmental Processor RAM NAND Flash External power supply range External voltage measurement Li-pol battery Modem Bands Modem antenna SIM GNSS receiver GNSS antenna IMU OBD protocols CAN interface Leds Connectors Operating temperature Dimensions ARM A7 2 Gbytes 2 Gbytes 8-18V 450mAh LTE Cat M1 & EGPRS Module (BG96) LTE : band 2, 4, 12 Internal Micro SIM clot U-blox M8 (GPS,GLONASS) Internal Accelerometer 3 axis 2/4/8/16 G CAN, KWP2000, VPW, PWM Single CAN coprocessor 1 bicolor LED OBD connector Micro USB type B connector

-20C/+50C with Battery

-20C/+60C without battery With OBD connector: 27x50x61 mm Without OBD connector: 27x50x49 mm 2. Hardware description 2.1. External view 1 : OBD connector 2 : micro USB connector 3 : bicolor led 2.2. Internal view 5 : GNSS antenna 6 : micro SIM holder 7 : Internal battery*

2 3 1 6 5 7

* Please read warnings section at the beginning of the installation guide 2.3 OBD connector pin out Pin # Comment 1 2 3 4 5 6 7 8 10 11 14 15 16 OEM specific J1850+ (PWM/VPW) OEM specific Chassis ground Signal ground CAN High K line OEM specific J1850- (PWM) OEM specific CAN low L line Battery voltage 2.4 OBD adapter wires This adapter is only used to connect the OBD to a computer (laptop/desktop). Pin # Wire color 2 4 5 6 7 10 14 15 16 Yellow Black Grey Green Blue Violet Orange White Red 3. Preparing/installing the device Those operations may need the use of specific tools like :

- Small cross-head screwdriver for the screw.

- Small slotted screwdriver to remove the cover.

- Thin tweezers to insert/remove the SIM card. 3.1. Open the device Remove the screw using Small cross-head screwdriver Insert slotted screwdriver to pop-out the top cover and extract it. Move apart the side of the device first and then pull the back cover out of his spot 2 1 Device is now open 3.2. Insert the SIM card The micro SIM card slot is located between the two electronic cards. Insert the card with contact on bottom into the slot and push it as far as it will go. Once inserted the SIM card looks like this:

3.3. Properly close the device First, check that the hole of the electronic card is correctly inserted in the plastic part. If its not inserted please move smoothly the electronic cards right and left to place it in correct position. Second, insert the GPS antenna as shown below. GOOD NOT GOOD Second, check that the micro USB port is correctly inserted on its place. If its not inserted please move smoothly the electronic cards to place it in correct position. GOOD NOT GOOD insert the GPS antenna as shown below. Finally, insert the battery and place the screw. 3.4. Install the OBD Dongle Connect the OBD Dongle on your vehicle OBD connector. 4. LED sequences The Dongle has a two-coloured LED, green and red. When both colours are brightened, you can see an orange light. Sequence Meaning Green LED No Modem

/No GNSS No Modem

/Fix GNSS Modem OK

/No GNSS Modem OK

/Fix GNSS 3 times (50ms ON/100ms OFF) 3550ms OFF 2 times (50ms ON/100ms OFF) 3700ms OFF 1 time (50ms ON/100ms OFF) 3850ms OFF 2000ms ON 2000ms OFF Sequence Dongle OFF Red LED Meaning OFF Ext. Power/Run ON Shutdown/Hibernate Idle/Sleep 30ms ON / 1 s OFF 30ms ON / 1 s OFF 5. Support For all questions not related in this installation guide, please contact the support team by email at support@munic.io

Ra Rev Dforw1202 | ZHAO Telematics embedded system MVNiIC Model : C4D-4MUSAA_V8 FE Input DC: 8 - 18V=2A max oa FCC ID : A6GC4D-4MUSV8 f

KR 3 3 S/N + XXXXXXXXXX

{TTTTITITTTTTTTTTTTTTTTTTANTUUULTTLLLTIT IMEL = XXXXXXXXXXXXXXX ET

{VTMTIVVIAI TVET eS Specification Dimension | 36mm * 34mm Model Label for OBD V8 CAT M1 US standard Colour black&white Material | PET MDI code MOTOO761AA Rev 1.0 Others: Gloss lamination(High gross) Draw Yanzhe ZHAO Date 07/01/2021 Scale 3:1 Unite mm

Version Date AA Rev1.0 21/01/2021 Editor Y.ZHAO Initial version Description

+0 R 1.5 mm

-0.4 36 +/-0.2 mm Manufactured by Telematics embedded system Model : C4D-4MUSAA_V8 Input DC : 8 - 18V 2A max FCC ID : A6GC4D-4MUSV8 3 4

0

. 2 m m Specicaon Dimension 36mm * 34mm Colour black&white Material PET Others Gloss laminaon(High gross) Model Label for OBD V8 CAT M1 US standard MDI code MOT00763AA Rev 1.0 Draw Date Scale Unite Yanzhe ZHAO 21/01/2021 3 1 mm

Version Date AA Rev1.0 07/01/2021 Editor Y.ZHAO Initial version Description

+0 R 1.5 mm

-0.4 36 +/-0.2 mm Manufactured by Telematics embedded system Model : C4D-4MUSAA_V8 Input DC : 8 - 18V 2A max FCC ID : A6GC4D-4MUSV8 3 4

0

. 2 m m Specicaon Dimension 36mm * 34mm Colour black&white Material PET Others Gloss laminaon(High gross) Model Label for OBD V8 CAT M1 US standard MDI code MOT00761AA Rev 1.0 Draw Date Scale Unite Yanzhe ZHAO 07/01/2021 3 1 mm

MUNIC 100 Avenue de Stalingrad 94800 Villejuif France Date: February 26, 2021 Federal Communications Commission 7435 Oakland Mills Road - Gate A Columbia, Maryland 21046 Subject: Request for Confidentiality FCC ID: A6GC4D-4MUSV8 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely. Schematic Diagram Block Diagram Operational Description Part List Tune-up procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFT 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant short-term confidentiality request on the following attachments until 180 days after the Grant Date of Equipment Authorizations. e External Photos Internal Photos Sd Test Setup Photos Users Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Meriem Zeraoui / Certification Manager Company: MUNIC Tel: 0033 1 79 84 12 64 E-mail: meriem.zeraoui@munic.io MUNIC 100 AV. DE STALINGRAD 94800 VILLEJUIF Tel: +33 01 42 11 93 25 Fax: +33 01 42 11 87 17

MUNIC 100 Avenue de Stalingrad 94800 Villejuif France Date: February 26, 2021 Power of Attorney To whom it may concern, Please be notified that I, Meriem Zeraoui, have designated Joey Lao of Bureau Veritas 7Layers Communications Technology (Shenzhen) Co. Ltd as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Joey Lao of Bureau Veritas 7Layers Communications Technology (Shenzhen) Co. Ltd on the matters relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. As defined in 47 CFR Ch. 1.U.S.C. 862, we further certify that neither the applicant nor any party to this application is subject to a denial to Federal benefits, including FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act. This authorization is limited to the product of as following:

FCC ID: A6GC4D-4MUSV8 If you have any acknowledgement and response, please send it to Joey Lao of Bureau Veritas 7Layers Communications Technology (Shenzhen) Co. Ltd directly. Should you have any question or comment regarding this matter, please have my best attention. Sincerely yours, Meriem Zeraoui / Certification Manager Company: MUNIC Tel: 0033 1 79 84 12 64 E-mail: meriem.zeraoui@munic.io MUNIC 100 AV. DE STALINGRAD 94800 VILLEJUIF Tel: +33 01 42 11 93 25 Fax: +33 01 42 11 8717

MUNIC 100 Avenue de Stalingrad 94800 Villejuif, FRANCE Product Equality Declaration Date: March 22, 2021 We, MUNIC, declare on our sole responsibility for the product C4D-4MUSAA_V8 that we accept the component sources mentioned below, and that they were tested for FCC compliance:

1. Product Information. Model: C4D-4MUSAA_V8 HW version: HC4D-4MUSAA_V8.01 a) Ferrite accepted and tested sources:

For this component at the same placement the sources listed below from different manufacturers are accepted and tested:

Description Reference on schematic Approved Manufacturer SMD EMI Suppression Ferrite L2, L3, L6, L301, L302, Wrth Electronik L304 Murata Beads WE-CBF b) TCXO accepted and tested sources For this component at the same placement both packaging dimension (3.2x2.5mm or 2.0x1.6mm) are accepted and tested (Sources from the different manufacturers listed below are accepted):

Description Reference on schematic Approved Manufacturer TCXO 3.2x2.5mm or 2.0x1.6mm Y3 26MHz 1.8V 2.0ppm Epson KDS Taitien ASK 1/3 c) Accelerometer alternative Source For this accelerometer feature both alternatives listed below are accepted and tested:

Alternative 1 :

Description Reference on schematic Reference of associated component on schematic MEMS digital output motion U21 R130, R131, R142, C92, Reference of Associated component C93, C94 on schematic sensor: ultra-low-

power high-performance 3-axis

"femto" accelerometer Alternative 2 :

Description Reference on schematic Reference of associated MEMS digital output motion sensor U23 ultra-low-power high performance three-axis nano accelerometer component on schematic C98, C99, C100 2/3