Headset E N D E F R I T E S N L P T S W D K T U P L G R R U F I T C Quick Guide Model No.: MBT-H120 FCC ID: HWF-MBTH120 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. Tested To Comply With FCC Standards FOR HOME OR OFFICE USE BLUETOOTH HEADSET GETTING STARTED BLUETOOTH HEADSET GETTING STARTED Any changes or modi cations not expressly approved by the party responsible for com-
pliance could void the authority to operate equipment. Identifying the Parts E N 1. Volume Up / Pairing Button 2. Power / Talking Button 3. Volume Down 4. Indicator LED Red : Power Off Blue : Power On Red+Blue : Pairing mode 5. Earhook 6. Earphone 7. Microphone 8. DC-IN jack 1 2 3 4 5 6 7 8 BLUETOOTH HEADSET GETTING STARTED BLUETOOTH HEADSET GETTING STARTED 3 Charging the Battery First time use:
Please charge the built-in Li-ion bat-
tery for 24 hours before the initial use. Remove the AC Adapter from the DC IN jack of the headset and the wall outlet. Low battery:
When the battery is low, the indicator LED will ash red. Please charge the battery for approximately 2.5 hours. How to charge:
1. Connect one end of the supplied AC Adapter (5V/0.5A) to the DC IN jack on the headset and the other end to the wall outlet. The indicator LED will light red when charging. After fully charging the battery, the indicator LED will light out. 4 BLUETOOTH HEADSET GETTING STARTED BLUETOOTH HEADSET GETTING STARTED Wearing the Headset Wearing the Headset To wear on your right ear:
Reverse the earhook to change its direction, and then follow the steps above to wear it on your right ear. E N You can wear the headset on either ear with the reversible earhook. To wear on your left ear:
Wear the headset vertically on your left ear. (Please refer to Figure 1) Rotate the headset toward the rear of your ear and point the microphone toward your mouth. (Please refer to Figure 2)
(Figure 1)
(Figure 2) BLUETOOTH HEADSET GETTING STARTED BLUETOOTH HEADSET GETTING STARTED 5 Powering the Headset On or Off To power your headset on:
Press the Power button for approxi-
mately 2 seconds until the indicator LED starts to ash blue. Then you can start to operate your headset. To power your headset off:
Press the Power button for approxi-
mately 2 seconds until the indicator LED starts to ash red. Once the indicator LED stops ashing, the power is OFF. 6 BLUETOOTH HEADSET GETTING STARTED BLUETOOTH HEADSET GETTING STARTED Before operating your headset with a Bluetooth phone, you must execute Pairing process to create a link between the devices. To pair with a Bluetooth phone, please follow the instruction below:
Ensure the headset is ON and enters the standby mode with ashing blue LED once rapidly every 3 seconds.
( Note: When powered on, the headset will attempt to connect to an available Bluetooth device. Please press the Power button to switch to the standby mode. ) 2. Press the Volume Up button for approximately 4 seconds until the indicator LED starts to ash red Pairing with a Bluetooth Phone E N and blue alternately, and enters the pairing mode. 3. Search for Bluetooth devices by following the phones operating instruction. 4. Select MBT-H120 from the searched devices list and con rm it. Enter the passkey 1234 and con rm it. After nishing the pairing process, the indicator LED will ash blue. is up to 10 meters (approximately 33 feet) between your headset and the
( Notes:
1) The operable range without obstructions Bluetooth devices. 2) Your headset can save the pairing infor-
mation of up to 8 phones, but connect to only one phone at a time. BLUETOOTH HEADSET GETTING STARTED BLUETOOTH HEADSET GETTING STARTED 7 Pairing with a Bluetooth Phone-continue If you have entered the passkey without previously pairing with another phone, the phone will be the default phone for your headset. If you want to use another Bluetooth phone with your headset, please switch the headset off, then disconnect it from the previous phone. Next, pair with another phone once restarted as described in page 7. ) 8 BLUETOOTH HEADSET GETTING STARTED BLUETOOTH HEADSET GETTING STARTED To answer or end a call:
When receiving a call, you will hear a ring tone through the headsets ear-
phone. Press the Power/Talk button to answer or end a call. To make a call:
There are two ways to make a call:
1. Using your phones keypad:
Press the Number button you want make a call. 2. Using the Voice Dialing function to call in your phones keypad to through your headset:
1) Record Voice Tags in your 2) Ensure this function is ON. 3) Press the Talk button, then say phone address book in advance. Call Functions the voice tag through your headsets microphone. 4) After recognizing the correct voice tag, the phone number will be dialed automatically. E N
( Note: This feature is only available with a phone that supports the Voice Dialing function. For details, please refer to your phones user guide. ) To redial the last call:
1. Press the Volume Down button for approximately 2 seconds when no call is in progress. To reject a call:
1. Press the Power button for approximately 2 seconds to reject an incoming call. BLUETOOTH HEADSET GETTING STARTED BLUETOOTH HEADSET GETTING STARTED 9 Headset Indicator LED While plugging in the charger:
Indicator LED Light Red Light Out Headset Charging Full Charge While unplugging the charger:
Indicator LED Flash Red Flash Red Light Out Flash Blue Flash Red and Blue Alternately Headset Low Battery Power Off Power On Pairing Mode 1010 BLUETOOTH HEADSET GETTING STARTED BLUETOOTH HEADSET GETTING STARTED Flash Blue LED once rapidly every 3 seconds Flash Blue LED twice rapidly every 3 seconds Flash Blue LED 3 times rapidly every 3 seconds Flash Blue LED 4 times rapidly every 3 seconds Signal Available
(Standby Mode) Connecting Connected Connected
(On a Call)