!D Gate 1x !D Gate 1x Coax cable 3m/10ft dimensions 300 150(2x) 13(6x) distance between antennas 462mm / 18.2 462
) x 2
0 6 7
. 7
m m 5
. 5 9 1
, 5 5 9 1
, t f 7
. 2
5 m 7 m 8 2 5 8 7
. 8 2 8 t f 7
. 5
8 m 6 6 m 1 8 6 6 1
) t r a p r o o
0 1
, t f 4
. 3 5
2 m 4 m 2 0 5 1 2 4 2 0 1
. 70mm / 2.8 70 57mm / 2.2 57 100mm / 3.9 100 recommended - 2.0m / 6.5ft absolute max. - 2.2m / 7ft orientation in the shop Power inserter all antennas in the same direction. B A B A B A sales floor B A B A stock room B A B A GROENLO - HOLLAND chk:
drw: CB 2013/06/13 description:
quick reference !D Gate Copyright by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be repro-
duced or distributed in any form or by any means, or stored in a data base or retrieval system without the prior written permission of NEDAP. doc. article no: 5278988 rev. : C.01 sheet: 45.01 of 1 drawing: T5278-988 01 remove covers 02 drilling holes 13mm / 0.5
. 5 3
m m 0 9 150 150mm / 5.9 300 300mm / 11.8 13(6x) 13mm / 0.5
. 4 2
0 m 6 m 0 6 03 Cleaning Hilti-hit Place nut Hilti-hit not included 05 04 4x M10 Metal M10 4 3 2 Nylon M10
(included in installation set) 1 Nut (not included in installationset) Nut (not included in installationset) Retainer ring (not included in installationset) Retainer ring (not included in installationset) Nylon Insulation ring Nylon Insulation ring (included in installationset)
(included in installation set) Iron Iron Reinforced Concrete Reinforced Concrete Always mount an antenna insulated to the oor or wall Always mount an antenna insulated to the floor or wall processing unit Power for Reader network IN USB host network OUT USB service port power supply Out In Power supply 9561811. One needed for every installed system. (not included) Not compatible with IEEE 802.3a* standard Recommended to place in switch-room 1 2 3 4 5 6 7 8 9 1 2 3
buzzer Processing unit at output No device at output or Lan- modem (in case of OST integration) Blink Continuous Power inserter at output Power error H G 1 Green 2 Blue Blue 3 Red F E
!D Reader previous next Led Blue Orange Red Firmware running Error
1 Yellow Heartbeat 2 Green Disk access 3 Green 12 10 11 Firmware running H G F E D C Green RFID active Green Power no coax cable needed coax cable 3m / 10ft 2x coax cable 3m / 10ft 1m / 3ft 0.5m / 1.5ft 1m / 3ft 1m / 3ft 0.5m / 1.5ft 1m / 3ft 2m / 6ft required label free zone 2m / 6ft recommended label free zone 01 02 03 2 2 2 1 previous next coax cable coax cable coax-cable 3m/10ft Minimum bending radius = >60mm/2.4 1 1 note:
use only cat5e ethernet cable or better, with all 8 wires connected.(straight cable) processing unit network IN OUT IN RJ45 connector to ethernet outlet - customer network. note:
use only cat5e ethernet cable or better, with all 8 wires connected.(straight cable) processing unit network IN processing unit network OUT RJ45 connector to ethernet outlet - customer network. place covers connect voltage supply 230V 110V Note :
The start up of all the processes takes approximately 3 minutes. use firmware configuration quick reference. Model: !D Gate Region 2 FCC ID: CGDSTOREIDG IC: 1444A-STOREIDG This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada.Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Cet appareil se conforme aux normes RSS 210 exempts de license du Industry Canada. Lopration est soumis aux deux conditions suivantes:
(1) cet appareil ne doit causer aucune interfrence, et
(2) cet appareil doit accepter nimporte quelle interfrence, y inclus interfrence qui peut causer une opration non pas voulu de cet appareil. Les changements ou modifications nayant pas t expressment approuvs par la partie responsable de la conformit peuvent faire perdre lutilisateur lautorisation de faire fonctionner le matriel. FCC and IC Radiation Exposure Statement:
This equipment complies with FCC and Canadian radiation exposure limits set forth for an uncon-
trolled environment. This equipment should be installed and operated with a minimum distance of 3.65 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet quipement est conforme a RSS-102 limites nonces pour un environne-
ment non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 3.65 cm entre le radiateur et votre corps. This Class B digital apparatus complies with Canadian ICES-003 Cet appareil numrique de Classe B est conforme la norme Canadienne ICES-003