FCC ID: CGDINVEXS170 Inductive Proximity Card Reader

3 6 9 E Invexs 170 readers Mifare Nedap dual technology readers Installation sheet 2 5 8 0

. 3 8 4 9 7 6 4 3 1 7 4 1 0 8 5 2 E C C 0 2 6.8 Invexs 170 reader series is capable of GENERAL The reading

(simultaneously) Nedap, Mifare and DESFire credentials due to its dual reader technology. The Invexs can read Mifare, DESFire and Nedap cards, and is equipped with keypad and /

or a display. The Invexs output can be set to either Wiegand, XS RF modulation or RS485 protocol (plain or encrypted) Functionality and output are determined by the configuration of the Invexs reader. The configuration is defined using the programm AEreco, and deployed by the configuration card or via AEmon. (More information about configurations can be found in ConvexsInvexs_InstallGuide_E.) Three LEDs (red, green, blue) and beeper are included (display version has no LED). Ciphers of the keypad versions light up after activation, so when not active the ciphers are not visible. Back panel is available in two colours, black and white (e.g. MNK170B, MNK170W) DIMENSIONS MOUNTING PROCEDURE INVEXS For mounting the Invexs, the back plane must be placed on the wall first. For removing the back plane from the Invexs, unscrew the two screws (1) at the bottom of the Invexs and push the front cover up (2). Mount the back plane using the 4 holes. Connections must be made on the connector on the backside of the front. After making the connections, replace the front and tighten up the two screws at the bottom of the Invexs. Dimensions: 171 x 75 x 25 mm. 4 mounting holes available at 52 x 120 mm Cable outlet: 40 x 40 mm Push up 75.2 24.5 0 2 1 0 7 1 40 52 2 0.5 1.5 0 4 C E 2 3 5 6 8 9 0 1 4 7 5 8

. 1 Version 5 Date : 23 February 2012 This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no licence under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher. Nedap N.V., IDEAS P.O. Box 103 NL-7140 AC GROENLO The Netherlands Part.no.: 5265800 Page 1 of 4 Un screw Invexs 170 readers 1 Invexs Function Power /

XSMOD POWER GND/Shield Invexs without display Power in (10-30VDC) /

XS modulator (120kHz) CONNECTIONS Invexs is not hot-swappable, so when making or changing connections power must be switched Off. Remark:

Wiegand Data 0 Wiegand Data 1 2 3 4 5 6 7 8 9 10 BEEP UL*

GND NA*

Beep input UL led input A (-) B (+) D0 D1 Invexs with display Led Common Ground RS485 RS485 Power Ground NA led input 10 5 1 6 1 10 1 1 Cable shield must be connected to Power GND of Convexs (A2) and GND of external device

(or metal case). If connected to a 120kHz RF device (AEOS Nedap reader AEpack or XS device) the power is supplied via the Convexs adapters (AX1014 for AEpacks, AB350 for XS devices). Existing antenna cabling can then be reused for connecting the ConveXS. UL*,NA* and BEEP are Open Collector to GND. If the Convexs adapters are used, the original UL and NA signals are converted to the UL* and NA*. R UL*/NA* / BEEP GND LED INDICATORS INSIDE There are two LEDs available: Blue for Status (of application), Green for Identification (both visible through two small holes at the back side) LED INDICATORS FRONT At the front a three colour LED is positioned at the middle of the Invexs Depending of the used configuration the function of these LEDs can differ:

Application running (operating) Downloading or error during loading Application present but not active No application present Slow blinking Fast blinking 2 short flashes 3 short flashes Blinking Card detected ST: STATUS (blue) ID (green) Green LED: Card is been authorised (UL led) Red LED:

Blue LED:

Card is not authorised (NA led), controller is stand-by Blinks fast:

No configuration is availabele at this Invexs (present Configuration Continuously ON: Determined by configuration: E.g. Reader stand-by. card or load Configuration first).

(Blue LED is activated if UL is OFF and NA is more than 1 sec OFF) Remark:

Function of LEDs and Beeper is controlled by used application settings of Invexs. Green and Red LED can be controlled by hardware signals (Connector 8 and 10) or RS485NR, Blue LED indirectly by UL and NA, if this setting is activated (configuration). Beeper can be controlled by hardware signal (Connector 7), RS485NR or software (configuration). Nedap N.V. Invexs 170 readers Installation sheet Page 2 of 4 FIRMWARE Pay attention that the firmware loaded in the Invexs together with the Invexs type and configuration determines functionality and protocols. For the Invexs with screen contact Nedap. Default (from factory) the Invexs handles the credentials on several ways simultaneously:

Invexs 170 readers XS cards as:

Mifare cards (CSN) as: RS485NR, RF data RS485NR, RF badge 1 2 3 4 5 6 7 8 9 C 0 E 1 2 3 4 5 6 7 8 9 C 0 E Wiegand interface Wiegand output connected to Third party systems (or to AEOS Wiegand interfaces). LEDs andBeeper are controlled by hard wiring. (PINcode possible) RF interface AEpacks AEOS RS485 interface RF interface XS systems

- Third party systems

- AEOS Wiegand To APx003 readers with RS485 special encrypted protocol. (LEDs, Beeper, Keys and Display are controlled over the RS485 communication) SYSTEM CONFIGURATIONS (how to connect Invexs readers) Remark: Configurations can be determined by using the configuration card. Attention: Check the ConvexsInvexs_InstallationGuide chapter 8 (Available reader Firmware) for the compatibility for the used readers. TAMPER SWITCH This tamper switch is an optical device, which is triggered by the amount of light. Depending on the applied configuration the result of activating the tamper switch can differ. BEEPER INDICATIONS Beeper is also used for indication of loading the configuration:

Invexs uses existing antenna cabling

(Coax + 3*0,25qmm for LEDs). On each XS reader-RF interface an AB350 must be added. Connections: see AB350 Invexs uses existing antenna cabling

(Coax + 3*0,25qmm for LEDs). On each AEpack-RF interface an AX1014 must be added. Connections: see AX1014 AX1014 AX1014 AX1014 Accessor III /

SimpleXS AX1014 AX1014 AB350 High sound beep (happy sound): Configuration is loaded correct, second high sound beep indicates that this configuration can be used with this Invexs Low sound beep (unhappy sound): Configuration is not correct loaded or no configuration available at startup Nedap N.V. Invexs 170 readers Installation sheet Page 3 of 4

..--. ~

c:=Ii::3 FI_R

-=In::,v..:.;e;;.:x""s:...1"-7'-'O'-r::..;:e:..::a:;.=d;.::.er=s SPECIFICATIONS Invexs 170 Product numbers see table below: For Screen / dis la ad Ke Reader contact Neda Screen / Dis M170B MI70W MD170B 9833900 9832750 9834400 MK170B MK170W MDK170B 9834230 9832920 9834680 MKS I 70B MKS 170W MDKSI70B la 9939822 9833390 9939849 MifareDESFrr~e __ _+~W~h~it~e--~MD~I~7~OW~--~9~83~4~3~7~0_+~MD~K~17~0~W~~~9~8~3~45~4~0~~M~D~K~S~I~70~W~~~98~9~1~8~20~

MNI70B 9834060 MNK170B 9833730 MNKS170B 9833870

~W~h~it~e--~MN~I~7~OW__ --~9~83~2~8~9~0-+~~~~17~O_VV__ ~~9~8~3~30~8~0~~M--N-K~S~17-0~W--~~98~3~3~4~20~

M170 Mifare MD170 Colour Black Wbite Black MN170 NtifareNedap MND170 Black Black Ntifare DESFire Ne=-=d=a!:..p_L~VVh~it~e __ L.:.:MND=::..:1~7..::0.:.:vv'---'-i MND170B 9899570

..:::9~89::..:9:...:4:.:::3~0_L~MND:::::...:::::;K:=.17:..::0:...:w-'---'-i~9:..::9:.:::3:::.87.:..:5::::3:....J.-'MND=.:=K::::Sc:.l.:...:70,,-,W,,----,---,,-99::..:3:.::8:..:.7::::88,,----, MNDKS170B MNDK170B 9938761 9938796 Dimensions:

171 x 75 x25 mm Power Supply:

IOVDC - 30VDC Weight: 200 gr Power consumption:

M.NKS:

70mA@12VDC, 140mA@12VDC, 35mA@24VDC 70mA@24VDC Environment:

Tamper switch:

Communication:

Inputs:

Indicators:

Antennas

(internal):

-30 - 65 C Relative humidity:

(firmware APx003rs485NR). to APx003,

(120 kHz for AXI014 Temperature: Operating: 0 - 55C, Storage:

Yes RS485 (Encrypted AEOS protocol Wiegand Data 0 and Data I (protocol depending of configuration) RF Modulator Beeper UL* led NA * led UL (green) NA (red) ,MD (blue) (if available) 120 kHz, Nedap XS compatible Antenna 1:

Antenna 2:

13,56 MHz, Mifare compatible

(Beep ON / OFF, controlled by application) to GND, max 20mA to GND, max 20mA Open collector Open collector or AB350)

(PM and AM cards). Open collector 10 - 93% non condensing RS485 plain to GND, max 20mA Detection distance UniXS card: 15 cm Detection distance Mifare card: 5 em I em Mifare EY1 card:

CABLE SPECIFICATIONS RS485:

ULlGND/NA:

XS MOD / GND:

Wiegand:

2 x 2 x 0,25mm'

3 x 0,25mrn', max cable length: 50 meter Coax RG58U, max cable length: 50 meter Or 5 x 0,25mm'

4 x 0,25mm'

shielded, max cable length: 50 meter, cable capacity <= 100pF/meter shielded (excl. LED's), max cable length:

ISO meter, depending on receiving device. shielded, max cable length: 1000 meter, cable capacity <= 100pF/meter MORE INFORMATION:

For more detailed information contact your local Nedap supplier or check the internet site.

Functionality and output are determined by the configuration of the Invexs reader. The configuration is defined using the programm AEreco, and deployed by the configuration card or via AEmon. (More information about configurations can be C 0 E C 0 E Three LEDs (red, green, blue) and beeper are included (display version has no LED). Ciphers of the keypad versions light up after activation, so when not active the ciphers are not visible. Back panel is available in two colours, black and white (e.g. MNK170B, MNK170W) CUBE Card reader MK170W / MK170B Invexs 170 readers Mifare Nedap dual technology readers Dimensions: 171 x 75 x 25 mm. 9205454 CUBE Card reader MK170W black cover white cover 4 mounting holes available at 52 x 120 mm Note :

Cable outlet: 40 x 40 mm Always disconnect the supply voltage before you install or modify the connection. Use an ESD-bracelet during the instalment. Cube products contain components which are sensitive to electrostatic discharge. 01 02 DIMENSIONS 6.8 8

. 4

. 3 0 2 Invexs 170 reader series is capable of black cover black cover GENERAL The reading

(simultaneously) Nedap, Mifare and DESFire credentials due to its dual reader technology. The Invexs can read Mifare, DESFire and Nedap cards, and is equipped with keypad and / or a display. The Invexs output can be set to either Wiegand, XS RF modulation or RS485 protocol (plain or encrypted) 9206167 CUBE Card reader MK170B Functionality and output are determined by the configuration of the Invexs reader. The configuration is defined using the programm AEreco, and deployed by the configuration card or via AEmon. (More information about configurations can be found in ConvexsInvexs_InstallGuide_E.) Three LEDs (red, green, blue) and beeper are included (display version has no LED). Ciphers of the keypad versions light up after activation, so when not active the ciphers are not visible. Back panel is available in two colours, black and white (e.g. MNK170B, MNK170W) For mounting the Invexs, the back plane must be placed on the wall first. For removing the back plane from the Invexs, unscrew the two screws (1) at the bottom of the Invexs and push the front cover up (2). Mount the back Connections must be made on the connector on the backside of the front. After making the connections, replace the front and tighten up the two screws 2 Push up 1 2 3 4 TORX 20 5 6 7 8 Dimensions: 171 x 75 x 25 mm. 4 mounting holes available at 52 x 120 mm Cable outlet: 40 x 40 mm 0.5 5

. 0 7 1 0 2 1 0 4 40 52 75.2 F E 1.5 24.5 D MOUNTING PROCEDURE INVEXS For mounting the Invexs, the back plane must be placed on the wall first. For removing the back plane from the Invexs, unscrew the two screws (1) at cable specifications :

the bottom of the Invexs and push the front cover up (2). Mount the back plane using the 4 holes. Connections must be made on the connector on the backside of the front. After making the connections, replace the front and tighten up the two screws at the bottom of the Invexs. C Version 4 Date : 12 October 2010 This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no licence under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher. RS485 - 2 x 2 x 0.25mm shielded. Nedap N.V., IDEAS P.O. Box 103 NL-7140 AC GROENLO The Netherlands B 04 F E D 1 4 7 C 2 5 8 0 3 6 9 E 1 Un screw F E Part.no.: 5265800 Page 1 of 4 C B A This information is furnished for guidance, and with no guarantee as to its accuracy or completeness; its publication conveys no licence under any patent or other right, nor does the publisher assume liability for any consequence of its use; specifications and availability of goods mentioned in it are subject to change without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher. wall-mounting D 4 2 3 1 03 Nedap N.V., IDEAS P.O. Box 103 NL-7140 AC GROENLO The Netherlands F E D C B A 4x screw

(not included) Ref.Nr. A REV. YYYY-MM-DD DATE Documentation released DESCRIPTION GROENLO HOLLAND GENERAL TOLERANCES SCALE:

FORMAT:

DIM. IN MM 1:1 A4 LIN. 0.2 ANG. 1 ROUGHNESS ACC. ISO 1302 in M N/A DESCRIPTION ISO A cable outlet 40 x 40 mm 3854418 Documentation released DESCRIPTION YYYY-MM-DD A REV. Ref.Nr. DATE

-

Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this

??

DSGN:

drawing may be reproduced or distributed in any form or by any means, or stored

??

in a data base or retrieval system without the prior written permission of NEDAP.

??

GROENLO HOLLAND GENERAL TOLERANCES SCALE:

FORMAT:

DIM. IN MM 1:1 A3 ROUGHNESS ACC. ISO 1302 in M DRW:

ANG. 1 ISO A N/A DESCRIPTION 1 LIN. 0.2 2 Assem mnk170 C

??

??

??

APPROVED YYYY-MM-DD YYYY-MM-DD YYYY-MM-DD DSGN:

DRW:

CHCK:

ARTICLE NUMBER REV. B N/A

-

APPROVED SHEET:

YYYY-MM-DD YYYY-MM-DD YYYY-MM-DD DRAWING:

A A 10.01 OF 1 N/A 4 A ARTICLE NUMBER REV. CHCK:

3 N/A A.01 10.01 OF 1 N/A 8 1 2 3 4 5 6 7 Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be reproduced or distributed in any form or by any means, or stored in a data base or retrieval system without the prior written permission of NEDAP. SHEET:

DRAWING:

GROENLO - HOLLAND description:

CUBE Card reader MK170W / MK170B | art no. 9205454 - 9206167 drw: CB 2012/07/05 chk:

doc. article no: 5279216 rev. : C Copyright by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be reproduced or distributed in any form or by any means, or stored in a database or retrieval system without the prior written permission of NEDAP. sheet: 45.01 of 1 drawing: T5279-216 05 connect Card reader to the CUBE Core or CUBE Access Plus F 1 2 3 E D 1 2 3 4 2 Connect reader(s) See wiring instructions reader MK170W MK170B Brown White Green Yellow

: +12V

: Ground GND

: RS485 +

: RS485 -

Reader A1 C A2 1 2 3 4 10 9 A3 To door locker connectors A4 To door locker 8 Use crimp connectors and isolation for wire extension B 1 Reader cable Black Cable White Brown Green Yellow See also pre-installation Signal name Reader Ground Reader Power +12V Red Reader RS485 +

Reader RS485 -

1 Yellow Blue A Cable shield must be connected to Power GND of CUBE Card-reader (A2) and GND of external device (metal case) 1 2

!

Blank wire 3 FCC ID: CGDINVEXS170 and IC: 1444A-INVEXS170 Ref.Nr. DATE

-

YYYY-MM-DD A REV. Documentation released DESCRIPTION Compliance statements (part15.19) This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. ROUGHNESS ACC. ISO 1302 in M LIN. 0.2 DESCRIPTION N/A ISO A cube GROENLO HOLLAND GENERAL TOLERANCES Cet appareil se conforme aux normes RSS210 exempts de license du Industry Canada. Lopration est soumis aux deux conditions suivantes:

(1) cet appareil ne doit causer aucune interfrence, et

(2) cet appareil doit accepter nimporte quelle interfrence, y inclus interfrence qui peut causer une opration non pas voulu de cet appareil. Copyright (c) by N.V. Nederlandsche Apparatenfabriek NEDAP. No part of this drawing may be reproduced or distributed in any form or by any means, or stored in a data base or retrieval system without the prior written permission of NEDAP. 4 5 6 3 Warning (part15.21) Changes or modifications not expressly approved by party responsible for compliance could void the users authority to operate the equipment.