SMARTDEACT Anti-Pilferage Device 14r01-Manual Users Manual

 

Pulse Listen Deactivation EN MANUAL SMARTDEACT 07 April 2014 This information is furnished for guidance, and with no guarantee as to its accuracy or completeness;

Its publication conveys no license under patent or other right, nor does the publisher assume Liability for any consequence of its use; specifications and availability of goods mentioned in it are Subject to change without notice; it is not to be reproduced in any way, in whole or in part, without the written consent of the publisher. N.V. Nederlandsche Apparatenfabriek Nedap info-rs@nedap.com Technical Support E-Mail Postal address Fax

+31 (0) 544-46 34 75 N.V. Nederlandsche Apparatenfabriek NEDAP, Parallelweg 2, 7141DC, Groenlo, The Netherlands Safety precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED NEDAP SERVICE PERSONNEL. Lightning flash with an arrowhead, enclosed in a triangle, alerts you to the presence of uninsulated voltage points inside the product which could cause a serious electrical shock. An exclamation mark enclosed in a triangle alerts you to important operating and maintenance instructions in the documentation provided with the product. WARNING! To avoid the risk of fire or electrical shock, never expose these products to water or operate in a high humidity environment. This European Standard specifies a marking







of electrical and electronic equipment in accordance with Article 11(2) of Directive 2002/96/EC

(WEEE); This is in addition to the marking requirement in Article 10(3) of this Directive which requires producers to mark electrical and electronic equipment put on the market after 13 August 2005 with a crossed-out wheeled bin symbol. that applies to electrical and electronic equipment falling under Annex IA of Directive 2002/96/EC, provided the equipment concerned is not part of another type of equipment that does not fall within the scope of this Directive. Annex IB of Directive 2002/96/EC contains an indicative list of the products, which fall under the categories set out in Annex IA of this Directive;

that serves to clearly identify the producer of the equipment and that the equipment has been put on the market after 13 August 2005. EN 50419:2005 2009 N.V. Nederlandsche Apparatenfabriek NEDAP Parallelweg 2, NL-7141 DC Groenlo The software / hardware described in this book / file is furnished under a license agreement and may be used only in accordance with the terms of the agreement. Copyright Notice All Rights Reserved. Any technical documentation that is made available by N.V. Nederlandsche Apparatenfabriek NEDAP is the copyrighted work of N.V. Nederlandsche Apparatenfabriek Nedap and is owned by N.V. Nederlandsche Apparatenfabriek Nedap. 14r01-manual cgdsmartdeact.doc | Nedap Retail Support 2 No warranty The technical documentation is being delivered to you and Nedap makes no warranty as to its accuracy or use. Any use of the technical documentation or the information contained therein is at the risk of the user. Documentation may include technical or other inaccuracies or typographical errors Nedap the right to make changes without prior notice. No part of this publication may be copied without the express written permission of N.V. Nederlandsche Apparatenfabriek Nedap Parallelweg 2, NL-7141DC, Groenlo, Netherlands. Trademarks Nedap, the Nedap logo, Nedap EASi/Net and the Nedap EASi/Net are registered trademarks of Nedap N.V. Nederlandsche Apparatenfabriek Nedap Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Printed in the Netherlands Notice The documentation is based in a Part numbers and Drawing number structure. Part number can also be named as Artikel nummer or Article number Drawing numbers can also be named as: Tekening Drawing numbers are build up in a the drawing Number with a structure Txxxx-yyy-zz Txxxx-yyy is the drawing number and extension number zz means:

10 11 12 Xxxx yyy is an overview drawing of the part and can contain wiring and circuit diagrams;

is the bill of material;

is the circuit diagram of the device.

= 0000 9999

= 000-999 14r01-manual cgdsmartdeact.doc | Nedap Retail Support 3 Introduction Table of content 1. 2. 3. 4. 5. System overview FCC Declarations Wiring diagram Specifications SMARTDEACT 5 6 7 8 9 14r01-manual cgdsmartdeact.doc | Nedap Retail Support 4 Introduction 1 N.V. Nederlandsche Apparatenfabriek Nedap further on called Nedap manufactures some of the most reliable and scalable EAS Systems of the market today. With this system your able to reduce the shoplifting costs the best in combination with Nedaps tag line. The SMARTDEACT is meant for Deactivation of disposable tags according to the Pulse Listen method. It detects a tag in the field and shell try to deactivate it until it is not functioning anymore. Some of the Smart Deactivator advantages are:

1. Constant optimal deactivation distance, independent of the tag frequency between 7.8 8.5 MHz 2. Different antenna sizes and shapes 3. Deactivation behavior programmable with switches 4. Detect only Mode 5. Deactivation on input 6. Forced deactivation on input 7. Short repeating acoustical feedback for successful deactivation, continue beep when deactivation unsuccessful. 8. Prepared for connectivity in RS485 bus structure 9. Sends only a deactivation burst when a tag is detected 10. Through air synchronization with Nedap OS/T systems and other SMARTDEACT s 11. Solid state output The SMARTDEACT produces an acoustic and visual signal when it detects an operating tag and tries to deactivate it. 14r01-manual cgdsmartdeact.doc | Nedap Retail Support 5 2 System overview 1 Mains Power Adapter

-965165 9

-965160 8 SMART DEAC RS485 commu nication SMART DEACTIVATOR Input Output LED An tenna Type: SDA-265x265 4 2 3 5 6 7 8 Figure 1 Functional system overview The SMARTDEACT system consists of the following components:

1. AC/DC Power adapter Wall Mount 100 240 VAC / 12 VDC. 2. Smart Deactivator electronics 3. Antenna Cable 4. Antenna Type: SDA-265x265 5. RS485 connection to communicate with the SMARTDEACT 6. Input for to be defined functionality 7. Output to be defined functionality 8. LED for visual indication The SMARTDEACT system is ready for use. You only have to follow the next steps:

Install the Smart Deactivator system according the: Prospect SMARTDEACT;

Power up the Smart Deactivator system;

Check the functionality; by deactivating a Tag above the antenna and check the sound. Call Nedap Customer Support for quick hands-on problem solution in case of unforeseen trouble (see Technical Support);

14r01-manual cgdsmartdeact.doc | Nedap Retail Support 6 3 Wiring Diagram Schematically diagrams below shows an example of the connections between used modules. The picture shows the full configuration that can be built up. Power adapter Deactivator Antenna Mains Power Adapter RS485 commu nication Input Output LED 1 3 2 SMART DEACTIVATOR SMART DEAC 4 An tenna SDA-265x265 The connections for a full configuration are:

1 DC power line Connects 12VDC from the Power Adapter to the Electronics Unit LED cable Connects the SMARTDEACT to the LED unit RS485 communication cable Connects the SMARTDEACT to a RS485 host device for example a personal computer Antenna cable Connects the SMARTDEACT to the SDA-265x265 antenna 2 3 4 14r01-manual cgdsmartdeact.doc | Nedap Retail Support 7 FCC Declarations 4 Compliance statements (part15.19) This device complies with part 15 of the FCC Rules and to RSS210 of Industry Canada. Operating is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. Cet appareil se conforme aux normes RSS210 exempts de license du Industry Canada. L'opration est soumis aux deux conditions suivantes:

(1) cet appareil ne doit causer aucune interfrence, et

(2) cet appareil doit accepter n'importe quelle interfrence, y inclus interfrence qui peut causer une opration non pas voulu de cet appareil. Warning (part15.21) Changes or modifications not expressly approved by party responsible for compliance could void the users authority to operate the equipment. This in particular is applicable for the antenna which can be delivered with the SMARTDEACT System. RF Exposure (OET Bulletin 65) To comply with FCC RF exposure requirements for mobile transmitting devices, this transmitter should only be used or installed at locations where there is at least 20 cm separation distance between the antenna and all persons. Information to the User (Part 15.106(b)) Note: This equipment has been tested and found to comply with the limits for a class B digital devices, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequent energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does not cause harmful interference to radio or television reception, which can be determine by turning the equipment off and on , the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver 14r01-manual cgdsmartdeact.doc | Nedap Retail Support 8 5 Specifications SMARTDEACT Enviromental Description Material Construction Protection Class Aluminium IP20 Min. Typical Max. Condition 8.2 7.8 MHz Operating frequency Operational temperature Storage temperature Relative Humidity Operating Distance Input Requirements and electrical specifications 0C

-10C 20%

0.3m Min. 90VAC 0.35A 47 Hz Description Input Voltage Input Current Line Frequency Inrush Current @25C Operation Voltage Power Regulations Safety approvals of the Power Adapter:

11.64VDC Typical 100-240

-

50-60Hz 12VDC 6W 8.5 MHz 40 C

+70C 90%

Max. 264VAC 0.7A 63Hz 12.6VDC non-condensing Antenna type dependant, Tag dependant Condition Full Range; 50/60Hz 264VAC - 90VAC

-

230VAC Cold Start 230VAC 50Hz cULus according to UL/CSA 60950-1 CB according to IEC60950-1 TUV EN60950-1 (2006) NEC Class 2 according to UL1310 CE Europe according to EN60950-1 Japan PSE Telecom system approval Cannada IC ID according to RSS210 IC ID:1444A-SMARTDEACT US according to FCC Part 15 FCC ID:CGDSMARTDEACT CE according to EN300330 Japan pending In compliance with Human exposure assessment according to:

EN62369-1 and EN50364 ICNIRP Guidelines IEEE C95.1 RSS102 ARIB STD-38 IEC62369-1 Electromagnetic compatibility EN 301 489 (Emission according to EN55022) IEC 61000-6-2 IEC 61000-6-3 CISPR 22 14r01-manual cgdsmartdeact.doc | Nedap Retail Support 9