FCC ID: 2ADLSWLSP-PI1101 Smart PIR Motion Detector

Smart PIR Motion Detector WL-ZSPWBPW-PI11-01 User User User Manual Nanjing IOT Sensor Technology Co., Ltd. Federal Communications Commission (FCC) Compliance Notice:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 1 Federal Communications Commission (FCC) Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2)This device must accept any interference received, including interference that may cause undesired operation. Federal Communications Commission (FCC) Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20cm during normal operation. 2 Function Illustration System Indicator Multi-functional Key Magnet Detection Area Battery Compartment Front of body Back of body Base 3 Features Realize remote monitoring and management via APP Client. In the state of Armed , when motion is detected in detection area, the mobile smart terminal would receive alarm notifications immediately. This product could also interwork with security devices to secure your home in all aspect. Wireless alarm notification, quick response, robust to interference, low false alarm rate. Self-adjustment to sensitivity in case of environment temperature change. Wide detection range, adjustable detection angle, which could be adjusted easily and conveniently. 4 Installation Steps Note: it is recommended to install this product 2.4m to 5m above ground. Option APlace it on any fixed flat surface Option BWall/Ceiling-mounted Step One: Mount two expansion plugs on the desired location of the wall/ceilings. Then fix the base with the self-tapping screws. Base Expansion plug Self-tapping screw 5 Wall/Ceiling Step Two: Open the cell cover and put in a CR2 battery. CR2 battery Cell Cover Back of Body 6

Step Three: Attach the body directly to the base and adjust it to a suitable angle to complete the installation. Note: Set the network before installation is completed. Wall/Ceiling 7

Network Setting 1. Add to network Quick click [Multi-functional Key] 4 times and [System Indicator]would flash in green to request to add to the ZigBee network. Then [System Indicator] goes out after staying green for 2s when it is added to the ZigBee network. 1 Quick click [Multi-functional Key] 4 times 2 Flash in searching for the network Go out after staying on for 2s when added to the network Back of body Front of body 8 2.Exit the network. Long press [Multi-functional Key ]for 10s and [System Indicator] goes out after flashing 4 times to exit the ZigBee network successfully and restore to factory settings at the same time. 1 Long press for 10s 2 Goes out after flashing 4 times Back of Body Front of Body 9 Note:

First make sure ZigBee network of the wireless gateway (additional purchase) is working well. Meanwhile, make sure this product is connected to power and is placed within the effective communication distance of the gateway. If remote control is needed, connect the gateway to WAN. When need adding this product to other gateways, please exit the current gateway ZigBee network then add it to the new gateway following above instruction. Factory settings defaults to out of ZigBee network. 10 How to use Under normal conditions [System Indicator] would not flash. In the state of armed, once motion is detected in detection area, [System Indicator] would flash red for once. And at the same time, the mobile smart terminal would receive alarm notification. 11 Cautions This product shall be installed according to the height specified in the user manual. Installing too high or too low would cause adverse effect to the angle and distance of detection. The shield, furniture, potted plant and other partitions shall not be placed in the detective range of this product. This product shall be placed away from air conditioners, refrigerators, stoves and other places as it is sensitive to change in temperature. It is recommended to not install in position with strong airflow to avoid false alarm caused by hot airflow and human movement. This product shall be inspected regularly to avoid malfunction and ensure proper operation. Do not drop this product in hight or smash it to avoid damage to internal components. Do not dissemble or refit this product and the accessories by yourself. In case of malfunction, do not dissemble this product by non-professionals, instead, deliver it to local service center or contact with our customer service directly.

! RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. 12 Specifications Communication Protocol Detection Range Detection Sensitivity Detection Speed Standby Consumption/Standby Current Mounting Heightm Power Supply DimensionsDiameterHeight, mm Detection Angle 13 IEEE 802.15.4 ZigBee/SmartRoom Circumference with 6m of Diameter

( Installation Height 3m) Once event 0.23.5m/s 30A 2.3-5 CR2*1 DC 3V 6438 120 Net Weightg Material& Color Flame Retardant Rating Operating Temperature Operating Humidity 50 PCWhite UL94 V-2

-10+45 95%RH (Noncondensing) 14 Statement: Hereby, Nanjing IOT Sensor Technology Co., Ltd declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Disposal and Recycling Information You can help protect the environment!

Please remember to respect the local regulations:hand in the non-working electrical equipments to an appropriate waste disposal centre The following marking is included in the product :

0700 15