V A N I N Quick Start Guide RX4-1500 Wi-Fi 6 Router Front Panel LED Status Indicators FCC ID:2AT9Z-RX4-1500 Before Setting LED indicator Status Description Green LED Indicator Solid on The router is starting or successfully connected to the internet. Fast blinking The router is performing WPS negotiation. Ports/ Buttons Description WPS/RST LAN 1, 2,3,4 Used to start the WPS negotiation process of the router, or to reset the router They are LAN ports used to connect to the wired device such as computers or switches LAN4 LAN3 LAN2 LAN1 WAN POWER ON/OFF WPS Reset WAN Port POWER Used to connect this router to the internet Used to connect to the included power adapter To customize your wireless network connection and other advanced router settings, please go to this website to download RX4-1500 User Guide for more information. www.Juplink.com/Support/
Operating Conditions Working Temperature: 0~40C / 32~104F Working Humidity: 10%~90% RH
(No condensation) Storage Temperature:-10~70C / 14~158F Storage Humidity: 5%~95% RH
(No condensation) Packing List Step 1: Basic Installation Modem AC Wall AC-DC power cord LAN4 LAN3 LAN2 LAN1 WAN POWER ON/OFF WPS Reset Modem LAN out Ethernet WAN IN Front Panel LED GREEN Juplink RX4-1500 Router Internet Ethernet cable AC-DC Adapter Quick Start Guide Use the included power adapter to connect the router to a power source. The LED indicator lights solid on. Turn on the modem that is providing your internet connection, then let it register with your ISP. Connect the WAN port of the router to a LAN port of your modem or to an Ethernet port. When The LED indicator lights solid on connect your device to the router. Step 2 Internet setting and wireless setting Step 32.4G Network Setting Step 4 5 G Network Setting WPS Pairing Connect to the wireless Network name shown on the back of the router ( you can change the network name and password later ) WLAN Juplink RX4-1500 Start a web browser on the device connected to the router. Enter 192.168.0.1 in the address bar and press enter. http://192.168.0.1 Username:admin / Password :admin Welcome to use Juplink Router Please input usename/password to login username admin password admin Login Cancel Other Wireless Modes Setting- AP Mode Setting Before Installation Please complete the following settings Connect a computer to the Juplink AP router and launch a web browser. Visit http://192.168.0.1 you are prompted to enter a username and password. The home page displays Status Network Security App Manage Help Network LAN 2.4G Setting 5G Setting SNTP WiFi Sync Guest SSID IP Address:
Subnet Mask:
192.168.0.1 255.255.255.0 Enable DHCP Server Start IP Address:
192.168.0.2 End IP Address:
192.168.0.254 Subnet Mask:
255.255.255.0 Select Network then select 2.4G setting. Select Network then select 5 G setting. Click the WPS connect on your device Customize your WiFi Name and WiFi Password, and Customize your WiFi Name and WiFi Password, and click Apply button. click Apply button. Status Network Security App Manage Help Status Network Security App Manage Help Network LAN 2.4G Setting 5G Setting SNTP WiFi Sync Guest SSID Network LAN 2.4G Setting 5G Setting SNTP WiFi Sync Guest SSID RX4-1500 WPS Connect Wireless Basic Conguration Noted this page allows you to set the wireless net work name (SSID) and password Wireless Basic Conguration Noted this page allows you to set the wireless net work name (SSID) and password Enable Wireless SSID Juplink_RX4-1500 Juplink_RX4-1500 5G Enable Wireless SSID Authentication Mode WPA-PSK/WPA2-PSK Authentication Mode WPA-PSK/WPA2-PSK WPA-PSK/WPA2-PSK Authentication is recommended WPA-PSK/WPA2-PSK Authentication is recommended Encryption AES Wireless Pre-shared Key *******
Encryption AES Wireless Pre-shared Key *******
Device WLAN connection page Press the WPS button for 3 seconds, the LED indicator blinking and enable the WPS-supported device within 2 minute to establish a WPS connection the LED indicator solid on. WPS Reset Apply Cancel Apply Cancel Back of your router view The router will reboot and you can reconnect with The router will reboot and you can reconnect with new wireless network name ( SSID ) and new password after 10 seconds. new wireless network name ( SSID ) and new password after 10 seconds. AP mode Installation Modem - LAN Modem Connect your Modem out to your AC router WAN Port AC Connect your AP router WAN Port to your AC router LAN Port Select Network and click LAN Manually set IP address as the following format 192.168.0.XXX ( XXX is any number of 2~254) Turn o DHCP function and click Apply button, setting nished. AC- WAN LAN1 LAN2 LAN3 LAN4 WAN POWER ON/OFF WPS Reset AC1- LAN AC2- LAN AP 1 AP 2 Note: If the default login credentials do not work, you might have changed the admin password. If you cannot remember your new password, you must perform a factory reset to restore the router to its factory default settings. For more information, see Restoring a Juplink home router to the factory default settings. Apply Cancel AP- WAN WPS Reset AP- WAN WPS Reset LAN1 LAN2 LAN3 LAN4 WAN POWER ON/OFF LAN1 LAN2 LAN3 LAN4 WAN POWER ON/OFF Nanjing Juplink Intelligent Technologies Co., Ltd. Address : No. 757 Dixiu Road, Binjiang Economic Development Zone, Jiangning District, Nanjing Technical support available by: Support@juplink.com Website: www.juplink.com Made in China 9 1 0 2
8 0 0 0 5 1
4 X R k n i l p u J
. d e v r e s e r s t h g i r l l A k n i l p u J 9 1 0 2 Q12: Why cannot My Windows device detect router wireless networks?
A12: If your Windows device is not detecting your AX routers wireless network, you might have an older Intel wireless network adapter
(some older Intel adapters include: Intel Dual Band Wireless AC-3160, AC-3165, AC-7260, AC-7265 and AC-8260). To check which wireless network adapter is on your Windows device:
Open the Control Panel. Enter Device Manager in the search bar at the top of the window. Click Device Manager. Click the arrow next to Network adapters to display the list of adapters. Your wireless network adapter displays on the list. Noted If your wireless network adapter is not made by Intel and you are still unable to connect to your routers SSID, try to reboot or reset your router If your wireless network adapter is an older Intel model, it might not recognize the wireless signal on your AX router. Connect to your router directly using a wired connection to access the Internet and download the latest network adapter drivers. To connect to your router directly and download the latest wireless network adapter drivers:
Using an Ethernet cable, connect your Windows device to a LAN port on the back of your AX router. Launch a web browser and visit https://downloadcenter.intel.com/product/59485/Wireless-Networking. Download the latest wireless network adapter drivers for your adapter model. After you install the latest drivers, your device should recognize your AX routers wireless network. FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement
(1)This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules.
(2)This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Caution Any changes or modifications not expressly approved by party responsible for compliance could void the users authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note
(1)the manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment.
(2)To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable. Trouble Shooting RX4-1500 Wi-Fi Router Juplink by VANIN Q1: Why cannot the router setup successfully?
A1: If router did not complete the setup you can try the following:
Press and hold the Reset button on your router with a paperclip or pin until the front illuminated turns off and the Green indicators start blinking (about 10 seconds). Install the router again. Q2: Why cannot the internet appears available?
A2: The Internet appears to be unavailable If the Internet has difficulty communicating with your router the problem may appear as a "Cannot find
[ lnternet address ]" message in your Web browser. If you know that the Internet address is correct and if you've tried several valid Internet addresses with the same result the message could mean that there's a problem with your ISP or modem communicating with your router. Try the following:
- Make sure that the network and power cables are securely connected.
- Make sure that the power outlet that your router is connected to has power.
- Reboot your router. Q3: Why unable to connect the router signal after a while of successful connection?
A3: Try the following:
-Check on the interface for restrictions and blacklist
-Reboot the router and connect again
-Reset the router and set up again Q4: How to reset the router if I cannot access the web UI of the router A4: When the LED of the router is solid on, press the reset button for 5 seconds and release. After the LED turns solid on, the router is restored to factory settings.If useless to press the Reset button, please confirm long press the Reset button for at least 5 second with power on. Q5: Why router and mobile get strong signal but low speed?
A5: Try the following:
- Enter the routers setting page and verify that your router gets no unknown access device in
- Check the surrounding wireless signals, If there are too many wireless signals, switch channels and try again.
- Check with your ISP by phone or email to confirm that the service is well. Q6: Why cannot access the web UI of the router after entering 192.168.0.1?
A6: Try the following solutions and log in again:
- Ensure that your Ethernet cable with internet connectivity is plugged into the WAN port of the router rather than a LAN port.
- Ensure that your wireless device is connected to the routers SSID.
- Ensure that your wired device is connected to port 1, 2 or 3, 4 of the router properly by Ethernet cable. And the device is also set to Obtain an IP address automatically and Obtain DNS server address automatically.
- Clear the cache of your web browser or replace the web browser, and try logging in again.
- Disable the firewall of your device, and try logging in again.
- If the problem persists, reset your router, follow the setting again. Q7: How to choose my connection type?
A7: You can choose your internet connection type based on the following table or by consulting your ISP Internet Connection Telephone line Ethernet cable Internet Connection Type PPPoE You need to double-click and enter a PPPoE user name and password to set up a dial-up connection. Q8: An IP address conflict message appears after a computer which is connected to the router. What should I do?
A8: Try the following:
- Ensure that there is no other DHCP server in your LAN or the other DHCP server is disabled.
- Verify that the IP address of your router is not used by another device in your LAN. The default IP address of the router is 192.168.0.1.
- Ensure that the static IP address assigned to the computer in your LAN is not used by other devices Q9: I forget the login password of the router. What should I do?
A9: Try to reset the router and log in the routers setting page. Q10 : Why cannot my phone find the 5 GHz signal?
A10: Try the following:
- Only devices supporting 5 GHz signal can find and connect to the 5 GHz network.
- Enter the router and Confirm that both signal bands have turned on. Q11 : Why cannot I access the internet after successfully connected to the routers network?
A11: Try the following:
- Make sure that an Ethernet or Internet cable is securely connected to the blue Internet port on the back of the router
- Make sure that an Ethernet or Internet cable is securely connected to the appropriate port on your modem
(This port on the modem is usually labeled Ethernet)