Users Manual Wireless PTT Pendant Operation:
Model: WPTT-PDNT-IOS Wireless PTT Pendant for WAVE with 3.5mm Female Connector and Power Cord FCC ID: 2A2BD-WPTT-PDNT-IOS Product Overview:
Package contents:
Wireless PTT Pendant Magnetic charging cable Users Manual Power ON: Press power ON/OFF button and hold for 3 second until Power on sound is heard by earphone; status LED flashes purple once to indicate device is turned on. Power OFF: Press power ON/OFF button, hold for 3 second until Power off sound is heard by earphone; status LED flashes purple once to indicate the device is turned off. PTT Button: Press and hold down this button to talk, release to end transmission. Volume control: Press volume up (+) / down (-) button to adjust volume. The device will produce a tone when volume reaches the minimum or maximum level. External earphone: Open external earphone jack dust cover, plug listen-only earphone with 3.5 2pole or 3pole connector. Status LED:
Status Power ON/OFF Charging Charge complete Low battery Pairing mode Connection Unpaired or lost link LED Indicator Flashes purple once Constant Red Constant Blue Flashes Red & Blue alternatively once every 3 seconds Flashes Red & Blue alternatively Flashes Blue 3 time every 3 seconds Flashes Red LED twice every 3 seconds How to Pair Process for radio / phone /
WAVE OnCloud 2. 1. 3. 4. Make sure Wireless PTT Pendant is OFF, press & hold power button to switch on. Wireless PTT Pendant is under pairing mode when the LED flashes Red and Blue alternatively and Pairing sound is heard by the external earphone. Start Bluetooth function on your radio / phone. Find the device name 2Way Audio under Bluetooth device list and connect it. Pairing process is completed, and Paired sound is heard by the external earphone. If a passcode is required on the display of the Bluetooth device, enter "0000". For some radios you may need to press "Connect" after pairing and connection confirmation sound is heard by earphone to establish the Bluetooth connection. Pairing Process for Zello 5.
1. 2. 3. 4. 5. 6. Follow the same procedure as pairing with phone. Launch the Zello app. Press "Options"->"Push-to-talk buttons"->"Add New Device"
Press the PTT Button once. You will see PTT-Z show up under OTHER BUTTONS. Click on it to select. You will see PTT-Z Connect Wireless PTT Pendant is now ready. General specification:
Model No. Microphone Protection grade PTT key life Talking Range Battery Charging time Operation temp. 0dB=1V/Pa WPTT-PDNT-IOS
-402dB@1KHz IP67 500,000 Times Bluetooth v5.0 class 2, 10 meters 260mAH Li-battery About 2 hours (5V 200mA)
-15~45C (5~113F) Troubleshooting:
Does not power ON Cannot charge Battery not holding charge Pairing issue RX / TX issue Check if device is charged Check connections to the device and wall outlet. Check if the devices charging contacts are in contact with optional desktop charging cradle. Check if charging status LED is on (RED) Check if battery is fully charged Battery has definite service life; replace the battery when it cant give sufficient run time even when its fully charged. Contact dealer to replace battery. Cannot find device, power off radio/phone for 5 second, restart and search again for device Check Bluetooth connection and pairing. Battery charging Use magnetic charging cable Charge Wireless PTT Pendant with the magnetic charging cable included, status LED indicates red while charging and turns blue when charging is complete.
(Please ensure the USB wall charger adapter has output of minimum 0.5A) Tips to ensure usage safety, optimal performance with longer usage life period. Avoid drop, collision and piercing product. Keep away from hazardous, corrosive chemical substances. Keep away from heat, flame or high temperature environment. Keep away from extreme cold, to avoid components damages. Close dust covers for earphone jack and charger jack when not in use. Store in dry and room temperature conditions. Do not charge with unauthorized or damaged charger. Charging with faulty charger may result in battery leakage, fire, and bursting. Do not charge the device with ambient temperature below 0C (32F) or above 45C (113F). Do not disassemble the product, it voids warranty and increases risk of water seal issue if product is not assembled correctly. If battery requires to be replaced, please contact your nearest service center for assistance. If product is not used for a period of time, charge the product every 2~4 weeks to keep battery well-conditioned. For prolonged storage, recommend storage temperature is 25C (77F). Charge the battery every 60 days will avoid battery getting deeply discharged and allow protection circuit to activate. ATTENTION This device complies with part 15 of the FCC Rules and ISED Canada license-exempt RSS standard(s). Operation is subject to the following 2 conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the interference to radio communications. instructions, may cause harmful However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. The device can be used in portable exposure condition without restriction. The product is too small to place complete label information, so the label is placed on the packaging box. 1. Using desktop charging dock Single charging dock A. Connect the AC/DC adapter to the jack on the back of the charging dock. Ensure the device is properly installed and makes proper contact with the docks contacts. Status LED indicates red while charging and turns blue when charging is complete. B. C. Cleaning:
2. Multiple charging docks (Maximum 10 units) A. Connect the charging docks. DO NOT connector more than 10 units. Connect the AC/DC adapter to the jack on the back of any charging dock. Status LED indicates red while charging and turns blue when charging is complete. B. C. Before cleaning make sure product is powered OFF, unplugged from charger and all dust covers properly closed. If necessary, the external surface of the speaker microphone may be cleaned with a mild soap solution and warm water. Do not use chemical solutions such as stain removers, alcohol, bleach or oil remover as this may damage or corrode product surface. Make sure water trapped inside speaker grill is shaken out before usage. Maintenance and safety: