all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
Exhibit 8 NAIS-400 user manual | Users Manual | 1.40 MiB | ||||
1 2 | Test Report | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Operational Description | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | External Photos | |||||||
1 2 | Test Report | |||||||
1 2 | Test Report | |||||||
1 2 | Test Setup Photos | |||||||
1 2 | Internal Photos | |||||||
1 2 | Attestation Statements | |||||||
1 2 | Internal Photos |
1 2 | Exhibit 8 NAIS-400 user manual | Users Manual | 1.40 MiB |
NAIS-400 Class B AIS Transceiver Instruction Manual ENGLISH simrad-yachting.com Preface As Navico is continuously improving this product, we retain the right to make changes to the product at any time which may not be reflected in this version of the manual. Please contact your nearest distributor if you require any further assistance. It is the owners sole responsibility to install and use the NAIS-400 AIS Class B Transceiver in a manner that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing safe boating practices. NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND AF-
FILIATES DISCLAIM ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW. Governing Language: This statement, any instruction manuals, user guides and other information relating to the product (Documenta-
tion) may be translated to, or has been translated from, another language (Translation). In the event of any conflict between any Translation of the Documentation, the English language version will be the official version of the Documentation. This manual represents the product as at the time of printing. Navico Holding AS and its subsidiaries, branches and affiliates re-
serve the right to make changes to specifications without notice. Copyright Copyright 2012 Navico Holding AS. Warranty The warranty card is supplied as a separate document. About this manual Important text that requires special attention from the reader is emphasized as follows:
Note: Used to draw the readers attention to a comment or some important information. Warning: Used when it is necessary to warn personnel that they should proceed carefully to prevent risk of injury and/or damage to equipment/personnel. 2 |
Preface | NAIS-400 Instruction Manual Contents 2 5 5 5 Preface Notices Safety warnings General notices About your AIS class B transceiver About AIS Static and dynamic vessel data Important information for US customers 9 9 9 10 11 Whats in the box?
14 14 16 Installation Preparing for installation Installation procedures 24 Configuring your AIS transceiver 24 24 25 Switching on your AIS transceiver for the first time Configuring your AIS transceiver Introduction to proAIS2 27 Operation 27 27 27 27 Using the AIS transceiver Switch functions Using proAIS2 with your AIS transceiver Indicator functions 29 Troubleshooting 30 Specifications Contents | NAIS-400 Instruction Manual
| 3 Table of figures 11 12 13 14 17 18 18 19 19 21 22 23 28 Items included with the product AIS transceiver overview Electrical connections to the AIS transceiver Typical installation configuration AIS transceiver dimensions AIS transceiver mounting GPS antenna mounting Position of the GPS antenna connector Position of the VHF antenna connector Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 Figure 6 Figure 7 Figure 8 Figure 9 Figure 10 Connecting an external switch Figure 11 Connecting to the NMEA0183 data port Figure 12 Connecting the power supply Figure 13 Indicator location on the AIS transceiver unit 4 |
Contents | NAIS-400 Instruction Manual 1 Notices When reading this manual, please pay particular attention to warn-
ings marked with the warning triangle. These are important mes-
sages for safety, installation and usage of the product. Safety warnings Warning: This equipment must be installed in accordance with the instructions provided in this manual. Warning: This AIS transceiver is an aid to navigation and must not be relied upon to provide accurate navigation information. AIS is not a replacement for vigilant human lookouts and other navigation aids such as RADAR. The performance of the trans-
ceiver may be seriously impaired if not installed as instructed in the user manual, or due to other factors such as weather and or nearby transmitting devices. Compatibility with other systems may vary and is reliant on the third party systems recognising the standard outputs from the transceiver. The manufacturer reserves the right to update and change these specifications at any time and without notice. Warning: Do not install this equipment in a flammable atmo-
sphere such as in an engine room or near to fuel tanks. General notices Position source All marine Automatic Identification System (AIS) transceivers utilise a satellite-based location system such as the Global Positioning Satel-
lite (GPS) network. The accuracy of a GPS position fix is variable and is affected by factors such as the antenna positioning, the number of satellites used to determine the position and for how long satel-
lite information has been received. Compass safe distance The compass safe distance of this unit is 0.2 m or greater for 0.3 deviation. Notices | NAIS-400 Instruction Manual
| 5 RF emissions notice Note: The AIS transceiver generates and radiates radio frequency elec-
tromagnetic energy. This equipment must be installed and operated according to the instructions contained in this manual. Failure to do so can result in malfunctioning of the receiver or personal injury. Note: Never operate the AIS transceiver unless it is connected to a VHF antenna. To maximise performance and minimise human exposure to radio frequency electromagnetic energy you must make sure that the an-
tenna is mounted at least 1.5 meters away from the AIS transceiver and is connected to the AIS transceiver before power is applied. The system has a Maximum Permissible Exposure (MPE) radius of 1.5 m. This has been determined assuming the maximum power of the AIS transceiver and using antennas with a maximum gain of 3 dBi. The antenna should be mounted 3.5 m above the deck in order to meet RF exposure requirements. Higher gain antennas will require a greater MPE radius. Do not operate the unit when anyone is within the MPE radius of the antenna (unless they are shielded from the an-
tenna field by a grounded metallic barrier). The antenna should not be co-located or operated in conjunction with any other transmit-
ting antenna. The required antenna impedance is 50 ohms. Warranty This product is supplied with standard warranty as defined in the accompanying warranty information. Warning: Any attempt to tamper with or damage the prod-
uct will invalidate the warranty. Disposal of this product and packaging Please dispose of the AIS transceiver in accordance with the European WEEE Directive or with the applicable local regulations for disposal of electrical equipment. Every effort has been made to ensure the packaging for this product is recyclable. Please dispose of the packaging in an environmentally friendly manner. Accuracy of this manual The AIS transceiver may be upgraded from time to time and future versions of the AIS transceiver may therefore not correspond exactly 6 |
Notices | NAIS-400 Instruction Manual with this manual. Information contained in this manual is liable to change without notice. The manufacturer of this product disclaims any liability for consequences arising from omissions or inaccura-
cies in this manual and any other documentation provided with this product. Declaration of conformity The manufacturer of this product declares that this product is in compliance with the essential requirements and other provisions of the R&TTE directive. The declaration of conformity is provided with the product document pack. The product carries the CE mark, notified body number and alert symbol as required by the R&TTE directive. The product is intended for sale in the following member states: Great Britain, France, Spain, Sweden, Austria, Netherlands, Portugal, Denmark, Norway, Belgium, Italy, Finland, Ireland, Luxem-
bourg, Germany and Czech Republic. FCC notice This equipment has been tested and found to comply with the lim-
its for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ-
ing interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equip-
ment. Warning: It is a violation of the rules of the Federal Communi-
cations Commission to input an MMSI that has not been properly assigned to the end user, or to otherwise input any inaccurate data in this device. Notices | NAIS-400 Instruction Manual
| 7 Industry Canada notice This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003. Le prsent appareil est conforme aux CNR dIndustrie Canada ap-
plicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1. Lappareil ne doit pas produire de brouillage, et 2. Lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le Fonc-
tionnement. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. 8 |
Notices | NAIS-400 Instruction Manual 2 About your AIS class B transceiver About AIS The marine Automatic Identification System (AIS) is a location and vessel information reporting system. It allows vessels equipped with AIS to automatically and dynamically share and regularly update their position, speed, course and other information such as vessel identity with similarly equipped vessels. Position is derived from the Global Positioning System (GPS) and communication between ves-
sels is by Very High Frequency (VHF) digital transmissions. There are a number of types of AIS device as follows:
Class A transceivers. These are similar to class B transceivers, but they are designed to be fitted on large vessels such as cargo ships and large passenger vessels. Class A transceivers transmit at a higher VHF signal power than class B transceivers and therefore can be received by more distant vessels, and also transmit more frequently. Class A transceivers are mandatory on all vessels over 300 gross tonnes on international voyages and certain types of passenger ves-
sels under the SOLAS regulations. Class B transceivers. Similar to class A transceivers in many ways, but are normally lower cost due to the less stringent performance requirements. Class B transceivers transmit at a lower power and at a lower reporting rate than class A transceivers. AIS base stations. AIS base stations are used by Vessel Traffic Sys-
tems to monitor and control the transmissions of AIS transceivers. Aids to Navigation (AtoN) transceivers. AtoNs are transceivers mounted on buoys or other hazards to shipping which transmit details of their location to the surrounding vessels. AIS receivers. AIS receivers will generally receive transmissions from class A transceivers, class B transceivers, AtoNs and AIS base sta-
tions but do not transmit any information about the vessel on which they are installed. This product is an AIS Class B transceiver. Static and dynamic vessel data There are two categories of information transmitted by an AIS trans-
ceiver: static and dynamic data. The vessels dynamic data, which includes location, speed over ground (SOG) and course over ground (COG), is calculated auto-
matically using the internal GPS receiver. About your AIS class B transceiver | NAIS-400 Instruction Manual
| 9 Vessel name Vessel call sign (if available) Vessel type Vessel dimensions Static data is information about the vessel which must be pro-
grammed into the AIS transceiver. This includes:
Maritime Mobile Service Identity (MMSI) In most countries the operation of an AIS transceiver is included under the vessels marine VHF licence provisions. The vessel on to which the AIS unit is to be installed must therefore possess a current VHF radiotelephone licence which lists the AIS system, vessel Call Sign and MMSI number. Warning: An MMSI number is required in order for the AIS transceiver to operate. Please contact the relevant authority in your country for more information. Important information for US customers There are specific laws in the USA regarding the configuration of AIS class B transceivers. If you are a US resident and intend to use your AIS class B transceiver in US waters, you should make sure that your retailer has configured your product prior to supplying it to you. If your AIS transceiver has not been pre-configured, please contact your dealer for details of how to have it configured. Warning: In the United States of America, the MMSI and static data must only be entered by a competent installer. The end user of the equipment is not authorised to enter their own vessel data. 10 |
About your AIS class B transceiver | NAIS-400 Instruction Manual Whats in the box?
Figure 1 shows the items included with your AIS transceiver pur-
chase. The following sections will give a brief overview of each item. Please ensure all items are present. If any of the items are missing, please contact your dealer. Class B AIS transceiver Power and data cable Screws
(packet of 4) Product CD Product manual Quick start guide Warranty information Figure 1 Items included with the product Support tools CD The CD supplied with the package contains the following:
proAIS2 software tool necessary to configure the AIS transceiver. Please refer to section 4 for details of the configuration process and how to use the proAIS2 tool. USB drivers required to connect to the AIS transceiver via USB. Alternative language versions of this manual. Quick start guide The quick start guide gives a handy one-page reference for the installation process. Product manual This document is the product manual and should be read thor-
oughly prior to any attempt to install or use the AIS transceiver. About your AIS class B transceiver | NAIS-400 Instruction Manual
| 11 Fixing screws Four fixing screws are provided with the product for mounting of the AIS transceiver. Please refer to the Installation procedures, chap-
ter 3 for details of how to mount the AIS transceiver. AIS transceiver unit Figure 2 shows an overview of the AIS transceiver unit. The AIS transceiver has a number of indicators which provide in-
formation to the user about the status of the AIS transceiver. Please refer to Indicator functions, chapter 5 for more details. The AIS transceiver has an internal GPS antenna. You should ensure that the transceiver is mounted where it has a clear view of the sky, or you can alternatively connect an external GPS antenna, which is available from your dealer as an accessory. Power, data and USB cable The power and data cable connects to the AIS transceiver and en-
ables connection to power, NMEA0183, external silent mode switch and USB. Warning: Do not attempt to adjust or remove the fixings next to each of the four mounting holes. These fixings form part of the sealing of the AIS transceiver and any modification could affect the products performance and will invalidate the prod-
ucts warranty. Indicator lights Green Amber Red Blue Mounting holes Mounting holes Power and data GPS antenna NMEA 2000 VHF antenna Figure 2 AIS transceiver overview 12 |
About your AIS class B transceiver | NAIS-400 Instruction Manual Electrical connections The AIS transceiver has the following electrical connections:
Power supply Two independent NMEA0183 data ports for connection to chartplot-
ters and other NMEA0183 compatible equipment USB for connection to a PC or Mac External switch input for silent mode control NMEA2000 port for connection to NMEA2000 compatible equip-
ment. In addition there are two other connections for the VHF antenna and an optional external GPS antenna. Figure 3 shows an overview of the electrical connections to the AIS transceiver. AIS Class B transceiver Power in Switch NMEA0183 device Chartplotter USB NMEA 2000 Figure 3 Electrical connections to the AIS transceiver About your AIS class B transceiver | NAIS-400 Instruction Manual
| 13 3 Installation Preparing for installation Figure 4 shows a typical installation configuration for the AIS trans-
ceiver. Please take the time to familiarise yourself with the system elements and their connections prior to attempting installation. VHF antenna AIS Class B transceiver GPS antenna
(optional) Chartplotter Power in Switch USB NMEA0183 device NMEA 2000 Figure 4 Typical installation configuration In addition to the items provided with your AIS transceiver the fol-
lowing items will be required for installation:
VHF antenna Connection to a suitable VHF antenna will be required for the AIS transceiver to operate. A standard marine band VHF antenna such as that used with VHF voice radios will be sufficient. Please take note of the warnings in section 1 regarding the use of antennas. Alternatively, if you wish to use an existing VHF antenna, antenna splitter products are available which allow the existing antenna to 14 |
Installation | NAIS-400 Instruction Manual be used with two radio devices, such as a VHF voice radio and the AIS transceiver. Warning: When selecting an AIS antenna splitter, make sure it is capable of operation with an AIS transceiver. Some AIS antenna splitters are designed to work only with AIS receivers. Please check with your dealer to ensure you purchase the correct type of antenna splitter. Optional external GPS antenna The transceiver has an internal GPS antenna. When the transceiver is mounted in a location with a clear sky view (for example, beneath a windshield or other non-metallic structure) an external GPS antenna is not required. Should it not be possible to mount the transceiver in a suitable location, then an external GPS antenna can be connected. A compatible GPS antenna is available from your dealer as an acces-
sory. Optional switch A switch can be connected to the transceiver to enable and disable silent mode (see Step 4 and 5 in Installation procedures, chapter 3. A latching toggle switch is required to use this feature. VHF antenna cable Please check that the VHF antenna you intend to use has sufficient cable to reach between the VHF antenna and the AIS transceiver unit. If it is not sufficient, you will need an extension cable. Please contact your dealer for details of suitable products. For reference, the VHF antenna connector type on the AIS transceiver unit is SO 239, and is intended to mate with a PL 259 connector. Power and data cable The AIS transceiver unit is supplied with a 2 meter long power and data cable as an accessory. If you require longer cables to reach your power supply, please ensure the cables are capable of carrying cur-
rents of up to 2A peak and 200mA on average. Means of connecting the cables together will also be required. The use of ScotchlokTM connectors is recommended for this purpose. Chartplotter To display received AIS messages from other vessels on your chart-
plotter, you will need to connect your AIS transceiver to your chart-
Installation | NAIS-400 Instruction Manual
| 15 plotter. Please refer to the user manual supplied with your chart-
plotter for details of how to connect and configure your chartplotter for use with AIS devices. For general guidance, your chartplotter should be configured to accept NMEA data at 38400 baud (some-
times referred to as NMEA HS in the plotter configuration menu). You may also need to enable the display of AIS targets in the chart options. Alternatively, if you use an NMEA2000 network on your vessel, it is possible to connect the AIS transceiver to the NMEA2000 net-
work via a suitable cable. Please contact your dealer for details of NMEA2000 cables. Connection to a PC or Mac If you choose to use a PC or Mac with suitable charting software to display received AIS messages from other vessels, this can be accomplished by connecting the USB connector on the supplied power and data cable. Installation procedures Before beginning the installation of your AIS transceiver, please ensure you have the necessary additional items as detailed in the previous section Preparing for installation. It is strongly recom-
mended that you read all of the instructions in this manual prior to installation. If, after reading this manual, you are unsure about any element of the installation process, please contact your dealer for advice. The following sections explain the installation process step by step for each of the main elements of the system. Step 1 - Installing the AIS transceiver Please note the following guidelines when selecting a location for your AIS transceiver:
The AIS transceiver must be fitted in a location where it is at least 0.5 m from a compass or any magnetic device. There should be adequate space around the AIS transceiver for rout-
ing of cables. See Figure 5 for details of the AIS transceiver dimen-
sions. The ambient temperature around the AIS transceiver should be maintained between -25C and +55C. The AIS transceiver should not be located in a flammable or hazard-
ous atmosphere such as an engine room or near fuel tanks. 16 |
Installation | NAIS-400 Instruction Manual The AIS transceiver is fully waterproof to ingress protection rating IPx7. However, it is recommended that the AIS transceiver not be subjected to extended periods of exposure to spray or submersion. It is acceptable to mount the AIS transceiver either vertically or horizontally. It is recommended that the AIS transceiver is installed in a below deck environment. The product is supplied with four selftapping screws for attachment of the AIS transceiver to a suitable surface. Please refer to Figure 6 for guidance. The AIS transceiver should be mounted in a location where the indicators are readily visible as these provide important information on the status of the AIS transceiver. If the internal GPS antenna is used, the AIS transceiver should be mounted in a location with a clear sky view. The internal GPS anten-
na is mounted below the top surface of the transceiver enclosure. Installation 128 mm 42 mm m m 2 4 m m 0 0 1 140 mm Figure 5 AIS transceiver dimensions Figure 5 AIS transceiver dimensions Page 13 Installation | NAIS-400 Instruction Manual
| 17 Figure 6 AIS transceiver mounting Step 2 - Installing an optional external GPS antenna For mounting of an optional external GPS antenna, you will require a 1-inch 14 TPI thread pole. You should ensure that the GPS antenna has a good clear view of the entire sky. It is not recommended that the GPS antenna is mounted up a mast where the motion of the vessel will cause the antenna to swing and potentially reduce the accuracy of the GPS position. Do not mount your antenna in the direct path of a radar transmitter. Feed the 10 m long cable attached to the GPS antenna through the pole and screw the antenna onto the pole mount as shown in Figure 7. Figure 7 GPS antenna mounting 18 |
Installation | NAIS-400 Instruction Manual Route the cable to your AIS transceiver unit, adding any necessary extension cables. Connect the cable from the GPS antenna to the GPS connector on the AIS transceiver as shown in Figure 8. Power and data NMEA 2000 GPS antenna VHF antenna Figure 8 Position of the GPS antenna connector Step 3 - Connecting the VHF antenna Route the cable from the VHF antenna to the AIS transceiver and connect to the VHF connector on the AIS transceiver as shown in Figure 9. A standard marine band VHF antenna or AIS antenna should be used with the AIS transceiver. The connector type on the AIS transceiver is SO239. Your chosen VHF antenna requires a PL259 connector to mate with this. If your VHF antenna does not use this type of connector, please contact your dealer for details of available adaptors. Power and data GPS antenna NMEA 2000 VHF antenna Figure 9 Position of the VHF antenna connector Installation | NAIS-400 Instruction Manual
| 19 Step 4 - Connecting the accessory cable An accessory cable is supplied with the product to provide con-
nections to power, the external switch, the NMEA0183 data ports and USB. The cable has a pre-moulded connector at one end which should be connected to the connector on the unit marked PWR/
DATA. The other end of the cable has eight colour-coded bare wires ready for connection and a USB connector for use with a PC or Mac. The table below lists the function of each colour-coded wire for reference. Function Power supply connections Wire colour Description Power in +
Red Black Power in -
Light green Switch input-
Switch input+
Orange Brown NMEA0183 port 1 TX+ High speed NMEA0183 output NMEA0183 port 1 TX-
Blue External switch connection for silent mode
(38,400 baud) intended for connection to chartplotters NMEA0183 port 2 RX+ Low speed NMEA0183 input NMEA0183 port 2 RX-
(4,800 baud) intended for connection to other NMEA0183 compatible sensors for multiplexing of data to the chartplotter Colour-coding of wires in the accessory cable Grey Yellow Warning: Please check your wiring very carefully before ap-
plying power to the product. Failure to wire the product correctly could result in permanent damage. Step 5 - Connecting an external switch A toggle switch can be connected to the AIS transceiver to provide remote control of silent mode. Connect the toggle switch between the light green and orange wires as shown in Figure 10. Connection of an external switch to toggle silent mode is optional and not es-
sential for normal operation of the product. Warning: Do not connect a voltage source across the switch inputs, as this may damage the transceiver. 20 |
Installation | NAIS-400 Instruction Manual Red Black Light green Orange Power in +
Power in Switch input +
Switch input Brown Blue Grey Yellow NMEA0183 38,400 Baud NMEA0183 4,800 Baud Transmit +
Transmit Receive +
Receive USB Figure 10 Connecting an external switch Step 6 - Connecting to NMEA0183 compatible equipment The two independent NMEA0183 data ports provide connection to your chartplotter and other NMEA0183 compatible equipment. Each port consists of two colour-coded wires, as shown in the table
(Step 4) and in the diagram in Figure 11. Connect the wires to the appropriate connections on your NMEA0183 compatible equip-
ment. Please refer to your equipment manual for more information. The AIS transceiver has a high speed output port, which operates at 38,400 baud and a low speed input port, which operates at 4,800 baud. The high speed port is intended primarily to connect to a chartplotter, while the low speed port is intended to connect to other NMEA0183 devices. A multiplexing feature is provided, which means any messages received via the low speed port are automati-
cally transmitted via the high speed port. This is particularly useful when using a chartplotter having only a single NMEA0183 port. An additional sensor, such as a gyro-compass, can be connected to the AIS transceiver via the low speed port and the AIS transceiver can be connected via the high speed port to the chartplotter resulting in the chartplotter receiving both AIS information and heading infor-
mation simultaneously. Please ensure your equipment is configured to use the correct baud rate for the port it is connected to. Installation | NAIS-400 Instruction Manual
| 21 Red Black Light green Orange Power in +
Power in Switch input +
Switch input Brown Blue Grey Yellow NMEA0183 38,400 Baud NMEA0183 4,800 Baud Transmit +
Transmit Receive +
Receive USB Figure 11 Connecting to the NMEA0183 data port Step 7 - Connection to an NMEA2000 network (optional) The AIS transceiver can be connected to an NMEA2000 network by a suitable NMEA2000 network cable available from your local dealer. If your vessel has an NMEA2000 network, please refer to the relevant documentation for your NMEA2000 equipment. Once connected, and with your chartplotter also connected to your NMEA2000 net-
work, you will be able to receive AIS targets on your chartplotter. Step 8 - USB Connection (optional) The AIS transceiver is supplied with a USB port for connection to a PC or Mac. The USB connector can be connected directly to the USB port on the PC or Mac via the supplied USB cable. To enable con-
nection of the AIS transceiver to a PC, the USB drivers (supplied on the product CD) must first be installed. Driver installation is typically not required for use with a Mac. To install the drivers, please follow the steps below:
Insert the product CD into the PC and navigate to the USB drivers folder. 1. 2. Double-click on the setup.exe file to launch the installer. 3. Follow the on-screen installation instructions to complete the installation. 4. Once installed, the AIS unit can be connected to the PC. The USB drivers will be installed automatically and the AIS will appear as a new COM port device. 5. Select the AIS COM port and a baud rate of 38,400 in PC based navigation 22 |
Installation | NAIS-400 Instruction Manual software to make use of the AIS data. Warning: If the USB connection is removed from the PC or Mac during use, you must reset the connection before further use. To reset the connection: disconnect, then re-apply power to the AIS before closing and re-launching any PC or Mac applica-
tions using the USB connection. Finally, re-connect the USB cable between the PC or Mac and the AIS transceiver. Step 9 - Connection to a power supply The AIS transceiver requires a 12V or 24V power supply, typically provided by the vessels battery. It is recommended that crimped and soldered lugs are used to connect the AIS transceiver to the power source. It is recommended that the power supply is con-
nected via a suitable circuit breaker and/or 3A fuse block. 1. Connect the red wire to a 12V or 24V power supply positive terminal. 2. Connect the black wire to the supply negative terminal. Red Black Light green Orange Power in +
Power in Switch input +
Switch input Brown Blue Grey Yellow NMEA0183 38,400 Baud NMEA0183 4,800 Baud Transmit +
Transmit Receive +
Receive USB Figure 12 Connecting the power supply Installation | NAIS-400 Instruction Manual
| 23 4 Configuring your AIS transceiver Until correctly configured, your AIS class B transceiver will only receive AIS messages and will not transmit AIS messages. Switching on your AIS transceiver for the first time A few seconds after applying power to the AIS transceiver, the indicators on the unit will illuminate in a pattern dependent on the configuration state of the unit. The function of the four indicators are:
Indicator Green Amber Red Blue Function Unit is powered up and operating normally Unit is in a 'transmit timeout' period Unit has experienced an error Silent mode is activated If the AIS transceiver has been pre-configured, the amber indicator will illuminate until a transmission has been sent by the unit. This may take several minutes, as the transceiver must acquire a GPS position fix prior to transmitting its first message. If the transceiver has not been pre-configured, the amber and red indicators will be illuminated until the configuration process has been completed. Configuring your AIS transceiver There are two potential ways in which your AIS transceiver can be configured:
1. Configuration in advance by your dealer or installer. If your AIS transceiver has been configured for you by your dealer or installer, you can proceed to chapter 5. 2. Configuration using proAIS2. Providing it is acceptable to do so under your local legislation, it is possible to configure your AIS transceiver yourself using the proAIS2 software provided with the product. 24 |
Configuring your AIS transceiver | NAIS-400 Instruction Manual Warning: US Customers only: It is a violation of the rules of the Federal Communications Commission for the enduser to programme the vessel data. The vessel data must only be programmed by a competent installer. If your AIS transceiver has not been pre-configured for you, please contact your dealer for advice on how to have the AIS transceiver configured by a competent installer. Introduction to proAIS2 Included in the CD supplied with your product is a software tool called proAIS2. proAIS2 provides the facility to configure, monitor and diagnose issues with your AIS transceiver. proAIS2 can provide assistance when ensuring that a satisfactory GPS signal is being received. It can also display alarm messages generated by the trans-
ceiver regarding poor VHF antenna quality or that the power being supplied is outside the range specified for operation. proAIS2 can also be used to activate silent mode, which disables AIS transmis-
sions. See the sections emmidiately below for how to install proAIS2 and how to configure the AIS transceiver using proAIS2. Further help on how to use the features of proAIS2 can be found in the Help menu within the proAIS2 tool. proAIS2 is designed to be installed and used with a PC or Mac connected to the AIS transceiver via USB using the supplied USB cable. 1. Installing proAIS2 Insert the CD into your PC or Mac, then locate and run the setup.exe file on the CD and then follow the on-screen prompts. 2. If a security warning appears, click Install to continue with the installation. 3. Once the installation is complete, proAIS2 will launch automatically and a start menu folder and shortcut will be created for future use. Configuration using proAIS2 For configuration purposes only, it is possible to power the AIS transceiver via its USB connection. This is useful if you wish to con-
figure your AIS transceiver away from the vessel power supply. The AIS transceiver will not transmit any data or acquire a GPS position fix whilst powered by USB. Configuring your AIS transceiver | NAIS-400 Instruction Manual
| 25 You will require the following information in order to configure your AIS transceiver:
MMSI Vessel name Vessel type Call sign Vessel dimensions and position of your GPS antenna installation. For further assistance in configuring your AIS transceiver, please refer to the Help menu within proAIS2. Warning: Please ensure that you enter all vessel data ac-
curately. Failure to do so could result in other vessels failing to identify your vessel correctly. The vessel MMSI can only be pro-
grammed once using proAIS2, please take care to programme your MMSI correctly. If you need to change the MMSI for any reason, please contact your dealer who will arrange to have the MMSI reset. 26 |
Configuring your AIS transceiver | NAIS-400 Instruction Manual 5 Operation Using the AIS transceiver Once the unit has been configured, it is ready for use. Providing that other vessels with AIS transceivers installed are within radio range of your vessel, you should see their details appear on your chartplotter or PC. These vessels will also be able to see your vessel on their chartplotter or PC. It may take up to six minutes for your full vessel details to be visible to others. Specific details of how to configure your chartplotter to make use of the AIS transceiver features will be given in your chartplotter manual. If you are using charting software running on a PC, please refer to the instructions provided with your chartplotting software for details of how to configure it to display AIS information. Switch functions When connected to the AIS transceiver and by following the in-
structions in Step 4 and 5 under Installation procedures, chapter 3, an external switch provides the ability to set the AIS transceiver into silent mode. In silent mode, the transmission of your own vessel position ceases, whilst the reception of other vessels AIS position continues. You should use silent mode if you do not wish your ves-
sel data to be received by other AIS devices. When silent mode is active, the blue indicator will be illuminated. Warning: When silent mode is active, other vessels will not be able to receive your vessel information on their AIS devices. Your navigational safety may be compromised as a result. Using proAIS2 with your AIS transceiver The proAIS2 tool has a range of features to help monitor the perfor-
mance of your AIS transceiver. To use the full range of features, your AIS transceiver must be installed as described in chapter 3 and con-
nected to a PC, running the proAIS2 application. Follow the instruc-
tions provided in the help menu within proAIS2. Indicator functions The AIS transceiver includes four coloured indicators, as shown in Figure 13. The state of the indicators provides information regarding the status of the AIS transceiver. Operation | NAIS-400 Instruction Manual
| 27 Indicator lights Green Amber Red Blue Figure 13 Indicator location on the AIS transceiver unit The meaning of typical indicator configurations is shown in the table below and Figure 13 shows the orientation of the AIS trans-
ceiver. Green indicator only The AIS transceiver is powered up, has a position fix and has transmitted at least one vessel information report. Red indicator only The AIS transceiver has detected a system error. The likely causes of this are detailed in the troubleshooting guide in chapter 6. Diagnostic messages displayed in proAIS2 may also help troubleshoot the cause of the error. Amber and blue indicators When silent mode is activated, using the optional silent mode switch, this combination of indicators is illuminated to show that the transmitter is disabled. Amber indicator only The AIS transceiver is in transmit timeout mode. This can be for a number of reasons:
- the unit has only recently been powered on and is obtaining a position fix prior to transmitting its first vessel information report.
(This process can take several minutes).
- position fix has been lost. The AIS transceiver will attempt to regain position fix for 30 minutes before entering an error state.
- the AIS radio channels are exceptionally busy, so there is currently no available timeslot for transmission.
- the unit has been in silent mode and after deactivating silent mode this amber indicator will illuminate until the first AIS message has been sent.
- the AIS transceiver has been commanded by the local authority (via an AIS base station) to cease transmissions. 28 |
Operation | NAIS-400 Instruction Manual 6 Troubleshooting Issue No data is being received by the chartplotter Possible cause and remedy Check that the power supply is connected correctly. Check that the power supply is a 12V or 24V supply. Check that the connections to the chartplotter are correct. Check that the power supply is connected correctly. Check that the power supply is a 12V or 24V supply. The unit may not have a valid MMSI. Check that the AIS transceiver is correctly configured with a valid MMSI. The VHF antenna may be faulty. Check the connection to the VHF antenna and that the VHF antenna is not damaged. The red indicator may illuminate briefly if the power supply is interrupted or the VHF antenna characteristics are briefly affected. No GPS position fix can be obtained. Check that the transciever is located where the internal GPS antenna has a clear sky view or that an external GPS antenna is properly connected and installed. Review the GPS signal strength graph available in proAIS2. The power supply is outside the allowable range. Check that the power supply is within the range 9.6V to 31.2V. If none of the above will correct the error condition, please contact your dealer for advice. Check for error and alarm messages in proAIS2 Some older AIS devices and chartplotters do not process the specific class B AIS message, which provides the vessel name (message 24). This is not a fault of your AIS transceiver. Software upgrades are available for many older chart-
plotters which will correct this issue. The other vessel should update its AIS unit and/or chart-
plotting software to receive AIS message 24. No indicators are illuminated The Red 'error'
indicator is illuminated My MMSI is being received by other vessels, but my vessel name is not shown on their chartplotter or PC If the guidance given in the table above does not rectify the prob-
lem you are experiencing, please contact your dealer for further assistance. Troubleshooting | NAIS-400 Instruction Manual
| 29 7 Specifications Value Parameter Dimensions 140 x 100 x 42 mm (L x W x H) 250 g Weight DC (9.6 V - 31.2 V) Power Average power consumption 170 mA at 12 VDC Peak current rating 2 A 50 channel IEC 61108-1 compliant GPS receiver (AIS internal) Electrical interfaces USB Connections VHF transceiver NMEA0183 38,400 k Baud output NMEA0183 4,800 k Baud input NMEA2000 LEN=1 VHF antenna connector (SO-239) External GPS antenna connector (TNC) USB type A plug NMEA2000 standard connector 12 way power input/NMEA0183/External switch Transmitter x 1 Receiver x 2 (One receiver time shared between AIS and DSC) Frequency: 156.025 to 162.025 MHz in 25 kHz steps 33 dBm 1.5 dB Bit rate Output power Channel bandwidth 25 kHz 25 kHz Channel step 25 kHz GMSK (AIS, TX and RX) Modulation modes 25 kHz AFSK (DSC, RX only) 9600 b/s 50 ppm (GMSK) 1200 b/s 30 ppm (FSK) Less than -107 dBm at 20% PER Co-channel 10 dB Adjacent channel 70 dB IMD 65 dB Blocking 84 dB RX sensitivity 30 |
Specifications | NAIS-400 Instruction Manual Parameter Environmental Indicators Value Water resistant to IPx7 Operating temperature: -25C to +55C Tested to IEC 60945 'Protected' category Power, TX timeout, error, silent mode status Specifications | NAIS-400 Instruction Manual
| 31
1 0 0
x x x 0 1
8 8 9
www.simrad-yachting.com
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2012-10-22 | 156.025 ~ 162.025 | AIS - Automatic Identification Systems | Original Equipment |
2 | JBP - Part 15 Class B Computing Device Peripheral |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2012-10-22
|
||||
1 2 | Applicant's complete, legal business name |
Navico Inc.
|
||||
1 2 | FCC Registration Number (FRN) |
0013828637
|
||||
1 2 | Physical Address |
4500 S. 129th East Avenue
|
||||
1 2 |
Tulsa, Oklahoma 74134
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
t******@babt.com
|
||||
1 2 |
T******@babt.com
|
|||||
1 2 | TCB Scope |
B3: Maritime & Aviation Radio Services equipment in 47 CFR parts 80 & 87
|
||||
1 2 |
A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices
|
|||||
app s | FCC ID | |||||
1 2 | Grantee Code |
RAY
|
||||
1 2 | Equipment Product Code |
NAIS400
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
J**** L********
|
||||
1 2 | Title |
VP, Global Quality, Quality assurance
|
||||
1 2 | Telephone Number |
+52 6******** Extension:
|
||||
1 2 | Fax Number |
+52 6********
|
||||
1 2 |
J******@navico.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 04/20/2013 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | AIS - Automatic Identification Systems | ||||
1 2 | JBP - Part 15 Class B Computing Device Peripheral | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Class B AIS transceiver | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | In addition to the labels or other identifying information required under 2.925 and 2.926 of this chapter, each Class B AIS device shall include a conspicuous label that includes: (i) instructions on how to accurately program into the device and confirm static data pertaining to the vessel in which the device is or will be installed; and (ii) the following statement: WARNING: It is a violation of the rules of the Federal Communications Commission to input an MMSI that has not been properly assigned to the end user, or to otherwise input any inaccurate data in this device. Instructions on how to accurately enter and confirm static data in the device shall also be included in the users manual for the device. This device operates on AIS 1 Channel 87 (161.975 MHz) and AIS 2 Channel 88B (162.025 MHz) with remote frequency assignment capability. This device also has DSC capability. | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
TUV SUD Product Service
|
||||
1 2 | Name |
M**** J****
|
||||
1 2 | Telephone Number |
00-44********
|
||||
1 2 | Fax Number |
00-44********
|
||||
1 2 |
m******@tuv-sud.co.uk
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 8 | CS | 156.025 | 162.025 | 2 | 1000 Hz | 9K85G7E | |||||||||||||||||||||||||||||||||
1 | 2 | 8 | CS | 156 | 163 | 2 | 1000 Hz | 18K0GXW | |||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15B |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC