FCC ID: RAYHALO3000 Pulse Compression Radar

HALO 2000 SERIES and HALO 3000 SERIES pulse compression radars INSTALLATION MANUAL ENGLISH www.simrad-yachting.com PAGE | 2 Disclaimer This product is not a substitute for proper training and prudent seamanship. It is the owners sole responsibility to install and use the equipment in a manner that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing maritime safety practices. Navigational features that appear in this guide are not a substitute for proper training and prudent seamanship. They do not replace a human navigator and SHOULD NOT be relied on as a sole or primary source of navigation. It is the operators sole responsibility to use more than one navigational method to ensure the route suggested by the system is safe. NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND AFFILIATES DISCLAIM ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW. This manual represents the product as at the time of printing. Navico Holding AS and its subsidiaries, branches and affiliates reserve the right to make changes to the product and/or specifications at any time without notice. Please contact your nearest distributor if you require any further assistance. Governing language This statement, any instruction manuals, user guides and other information relating to the product

(Documentation) may be translated to, or has been translated from, another language (Translation). In the event of any conflict between any Translation of the Documentation, the English language version of the Documentation will be the official version of the Documentation. Copyright Copyright 2022 Navico Holding AS. Warranty The warranty card is supplied as a separate document. In case of any queries, refer to the brand website of your display or system:

www.simrad-yachting.com. Declarations and conformance This equipment is intended for use in international waters as well as coastal sea areas administered by countries of the E.U. and E.E.A. Compliance statements Declarations The relevant declarations of conformity are available on the following website within the radars documentation section: www.simrad-yachting.com. United Kingdom Simrad HALO 2000 SERIES and HALO 3000 SERIES pulse compression radars comply with UKCA under The Radio Equipment Regulations 2017. The Simrad HALO RI-50 interface module complies with UKCA under The Electromagnetic Compatibility Regulations 2016. Europe Simrad HALO 2000 SERIES and HALO 3000 SERIES pulse compression radars comply with CE under RED Directive 2014/53/EU. The Simrad HALO RI-50 interface module complies with CE under EMC Directive 2014/30/EU. PAGE | 3 United States of America THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Warning: Navico is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the users authority to operate the equipment. RF emissions notice This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This devices antenna must be installed in accordance with provided instructions, and it must be operated with a minimum spacing of 177.97 cm (5.84 ft) for the HALO 3000 SERIES and 106 cm (3.48 ft) for the HALO 2000 SERIES between the antenna and a persons body (excluding extremities of hands, wrist and feet). Be aware that these FCC safety distances are calculated for a non-rotating antenna that is transmitting. For radio frequency safe distances for an antenna that is rotating and transmitting, see the Radio frequency (RF) safe distances table on the next page of this manual. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help. Note: HALO 2000 SERIES and HALO 3000 SERIES radars dont transmit when the antenna isnt rotating, so pose not risk in this situation. Canada English This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Franais Le prsent appareil est conforme aux Innovation, Sciences et Dveloppement conomique Canada

(ISDE) applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Innovation, Science and Economic Development Canada (ISED) statement English Under ISED regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. PAGE | 4 The radio transmitters, 978B-HALO2000 and 978B-HALO3000, have been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Franais Conformment la rglementation dInnovation, Sciences et Dveloppement conomique Canada

(ISDE), le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal

(ou infrieur) approuv pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpassepas lintensit ncessaire ltablissement dune communication satisfaisante. Les prsents metteurs radio, 978B-HALO2000 et 978B-HALO3000, ont t approuvs par Innovation, Sciences et Dveloppement conomique Canada (ISDE) pour fonctionner avec les types dantenne numrs ci-dessous et ayant un gain admissible maximal et limpdance requise pour chaque type dantenne. Les types dantenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour lexploitation de lmetteur. HALO antennas Description Max. permissible antenna gain (dBi) Impedance 000-11464-001 Antenna, 3 ft, HALO 26 50 Ohm (WR-90 waveguide) 000-11465-001 Antenna, 4 ft, HALO 27.2 50 Ohm (WR-90 waveguide) 000-11466-001 Antenna, 6 ft, HALO 29 50 Ohm (WR-90 waveguide) Radio frequency (RF) safe distances Figures in the table below show the radio frequency radiation safe distance for an operating

(rotating) antenna is within the antennas turning circle. Irrespective, users should stay well outside the turning circle of the antenna to avoid injury through physical impact as it spins. System 100 W / m2 occupational safe distance 10 W / m2 public safe distance HALO 2000 SERIES radars Within antenna turning circle 1.5 m (4.9 ft) HALO 3000 SERIES radars 0.8 m (2.6 ft) 2.5 m (8.2 ft) Trademarks Reg. U.S. Pat. & Tm. Off, and common law marks. Visit www.navico.com/intellectual-property to review the global trademark rights and accreditations for Navico Holding AS and other entities. Navico is a registered trademark of Navico Holding AS. Simrad is a registered trademark of Kongsberg Maritime AS, licensed to Navico Holding AS. HALO is a registered trademark of Navico Holding AS. VelocityTrack is a trademark of Navico Holding AS. ZoneTrack is a trademark of Navico Holding AS. Precision is a trademark of Navico Holding AS. GO is a trademark of Navico Holding AS. NSS evo3 is a trademark of Navico Holding AS. NSS evo3S is a trademark of Navico Holding AS. NSO evo3 is a trademark of Navico Holding AS. NSO evo3S is a trademark of Navico Holding AS. NSO evo3S is a trademark of Navico Holding AS. PAGE | 5 XSE is a trademark of Navico Holding AS. XSR is a trademark of Navico Holding AS. R2009 is a trademark of Navico Holding AS. R3016 is a trademark of Navico Holding AS. NMEA 2000 is a trademark of the National Marine Electronics Association. Tef-Gel is a trademark of Ultra Safety Systems, Inc. About this manual This manual is a reference guide for installing the Simrad HALO 2000 SERIES and HALO 3000 SERIES pulse compression radars. It does not cover basic background information about how equipment such as radars, echosounders and AIS work. Such information is available from our website: www.support.simrad-yachting.com. Intended audience This manual assumes the reader has basic knowledge about this type of equipment with regards to:

installation work to be carried out nautical terminology and practices. Translated manuals Translated versions of this manual can be found on the website: www.simrad-yachting.com. PAGE | 6 CONTENTS 8Introduction 8Warnings 9Check the parts 9Pedestal 10Antenna 10RI-50 radar interface module 11Tools required 12Installation guidelines 12What not to do 13Compass safe distance 13Multi-radar installations 13Power boat installations 14Considerations for roof mounting 17Hardware mounting 17Install the RI-50 radar interface module 18Run the interconnection cable 18Install the pedestal 19Surface mount: rear cable connection 22Pole or tower mount: discreet cable connection 23Fit the antenna to the pedestal 26Wiring 26RI-50 circuit board 27Run the cables 28Connect the interconnection cable 29Connect the power cable 30Ground the RI-50 31Activate remote power control 32Activate antenna park 33Connect the network cables 34Additional radar functions 35Start the radar 36RI-50 LED indicator lights 38Fuse 39Setup and configuration 39Radar source 39Radar status 39Antenna setup 39Adjust bearing alignment 39Sidelobe suppression 39Sector blanking 39Adjust open array park angle 39HALO light 39Reset radar to factory defaults 40Error codes 41Upgrading 41Record the old settings 41Isolate power to the radar 41Remove the old pedestal 42Remove the RI-12 43Install the RI-50 and new pedestal 44Specifications 47Drawings 47RI-50 48Pedestal and antennas 49Antenna turning circle diameters 50Parts list PAGE | 7 INTRODUCTION This manual explains how to install the latest generation of HALO open array, pulse compression radars the HALO 2000 SERIES and HALO 3000 SERIES. This manual should be used in conjunction with the installation manual provided with your multi-

function display. It is written for professional marine technicians, installation technicians and service technicians. Dealers may use information contained in this document. HALO 2000 SERIES and HALO 3000 SERIES radars combine the best characteristics of traditional pulse and FMCW broadband radar systems. Pulse compression technology provides an unprecedented mix of long and short detection range, high target definition, and minimal clutter. Solid state technology means minimal warm-up time and maximum ocean-going reliability. This latest generation of HALO open array radars incorporate updated hardware and mechanical design improvements that deliver increased power, improved long-range target detection performance and more system reliability. HALO 2000 SERIES and HALO 3000 SERIES radar systems consist of a pedestal, antenna, RI-50 radar interface module and connection cables. A supplied Ethernet network cable connects the RI-

50 radar interface module to the navigation Ethernet network. Notes:

HALO 2000 SERIES and HALO 3000 SERIES radar systems are available with antennas in three sizes: 3 ft, 4 ft and 6 ft. At the time of release, HALO 2000 SERIES and HALO 3000 SERIES radars work with Simrad GO XSR, GO XSE (9/12), NSS evo3, NSS evo3S, NSO evo3, NSO evo3S and NSO evo3S MPU systems. They also work with Simrad R2009 and R3016 radar control units. Warnings Use the radar at your own risk. Your radar is designed as a navigation aid. Always compare the navigation information received from your radar with data from other navigation aids and sources. When a conflict arises between the navigation data from your radar and data from other navigation aids, make sure you resolve the conflict before proceeding with navigation. A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN NAVIGATION INFORMATION. International Regulations for Preventing Collisions at Sea mandate that when radar is on a vessel, the radar must be used at all times, regardless of weather conditions or visibility. Numerous court decisions have ruled that the radar must be used, and the radar operator must know all operational aspects of radar performance. Otherwise they will face a greater risk of liability if an accident occurs. High current, stored and microwave energy hazard. Technicians must exercise extreme care when working with the unit. ALWAYS disconnect from the power source before removing the cover. Some capacitors may take several minutes to discharge, even after switching off the radar. Before touching any high voltage components, ground them with a clip lead. The radars blue 4-level static accent pedestal lighting may not be approved for use in your boating location. Please check your local boating regulations before turning the blue accent lights ON. The microwave energy radiated by a radar antenna is harmful to humans, especially the eyes. NEVER look directly into an open waveguide or into the path of radiation from an enclosed antenna. Disconnect from the power source or use the service mode switch on the back of the pedestal whenever you need to work on the antenna or other equipment in the beam of the radar. PAGE | 8 CHECK THE PARTS Pedestal 1 2 3 4 5 e d c b a 6 7 8 Radar pedestal Interconnection cable 20 m (65 ft). Other lengths are available from your nearest Simrad dealer. Lifting strap Blanking plug (used when the interconnection cable is connected underneath the pedestal. Blanking plug is fitted underneath the pedestal when manufactured.) Tef-Gel anti-seize, anti-corrosion gel Mounting bolts and washers a) Bolts, hex head, M12 x 35 mm, 316 s/s b) Bolts, hex head, M12 x 50 mm, 316 s/s c) Flat washer, M12 x 36 x 3, 316 s/s d) Spring washer, M12, 316 s/s e) Plastic isolating washer, M12 x 38 x 4 x 4 x 4 x 4 x 8 Mounting template This manual 1 2 3 4 5 6 7 8 PAGE | 9 Antenna 1 4 3 2 1 2 3 4 Radar antenna 3 ft model: 3.70 ft / 1128 mm / 44.41 4 ft model: 4.70 ft / 1432 mm / 56.38 6 ft model: 6.69 ft / 2039 mm / 80.28 Dome nuts, M8, 316 s/s Spring washers, M8, 316 s/s Flat washers, M8 x 16 x 1.2, 316 s/s x 4 x 4 x 4 RI-50 radar interface module 1 2 5 6 4 3 7 1 2 3 4 5 6 7 RI-50 radar interface module 4-way connector for the pedestal interconnection cable 2-way connector for the pedestal interconnection cable Connector for Aux in (remote power and antenna park brake) Mounting screws, Phillips pan head, No. 6 x 45 mm, s/tap, 304 s/s x 4 Ethernet adapter RJ45 male to 5-pin female 150 mm (5.9) Ethernet cable 1.8 m (6.0) PAGE | 10 TOOLS REQUIRED 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 7 8 9 10 11 Drill Torque wrench 19 mm socket 13 mm socket Drill bit 13 mm (0.5) Sharp knife Screwdriver (Pozidriv, PZ2) for RI-50 mounting screws Screwdriver (Phillips, #1) for RI-50 circuit board cover screws Screwdriver (flat head, 4 mm) for SUPPLY and SCANNER POWER connectors Screwdriver (flat head, 3 mm) for AUX connectors RJ45 crimping tool (if refitting/replacing the RJ45 connector) PAGE | 11 INSTALLATION GUIDELINES Warning: A radar should only be installed by a qualified marine technician, as improper installation poses risks to the installer, the public, and to the safety of the vessel. Warning: Before starting the installation or any maintenance on a HALO 2000 SERIES or HALO 3000 SERIES radar, make sure the service mode switch at the back of the pedestal is set to 0 (power supply disabled). There is a transmit interlock that prevents radar transmissions if the antenna is not rotating. However, a high voltage remains for a period of time after the system is turned off. If you are not familiar with this type of electronics, consult a trained service or installation technician before trying to service any part of the equipment. Installation includes:

hardware mounting electrical wiring configuring the display or network system to work with the radar adjusting the radar for proper performance. The radars ability to detect targets depends greatly on its location. The ideal location is high above the vessels keel line where there are no obstacles. A higher installation location improves the radars ranging distance, but it also increases the range around the vessel where targets cannot be detected and increases sea clutter pick up. When you are deciding on the location, consider the following:

The length of the 20 m (66 ft) interconnection cable supplied with the radar is usually sufficient. A longer 30 m (98 ft) cable is available. 30 m (98 ft) is the longest the cable that can be used. If the roof of the wheelhouse is the highest existing location, consider installing a radar mast or tower on which you can mount the radar. If you install the radar on the mast, position it on the forward side so there is a clear view to the front of the vessel. It is preferable to install the antenna parallel to the line of the keel. What not to do Do not install the radar too high, where its weight may compromise the stability of the vessel and degrade the radar picture over short ranges. Do not install the radar close to lamps or exhaust outlets. Heat, soot, and smoke emissions may degrade radar performance or cause a breakdown. Do not install the radar where a large obstruction (such as an exhaust stack) is at the same level as the beam. The obstruction is likely to generate false echoes and/or shadow zones. If there is no alternative location, use the radars sector blanking setting on your multi-function display. Do not install the radar close to the antennas of other equipment, such as direction finders, VHF antennas and GPS equipment, as it may cause interference. Do not install the radar where may be subjected to strong vibrations that could degrade its performance. Do not install the radar close to halyards or flags because the wind could wrap these around the antenna and jam it. PAGE | 12 Compass safe distance Do not install your HALO radar or RI-50 inside of the recommended safe distances of navigational instruments like the magnetic compass and chronometer. HALO 2000 SERIES and HALO 3000 SERIES pedestal Antenna Compass Standard load Standard Safe distance 1.0 m (3.3 ft) Standard load Standby steering/emergency 0.5 m (1.6 ft) RI-50 interface module Compass Standard Safe distance 0.1 m (0.33 ft) Standby steering/emergency 0.1 m (0.33 ft) Multi-radar installations Do not install your HALO 2000 SERIES or HALO 3000 SERIES radar on the same horizontal beam plane as any other radar. Separate them vertically by at least 2 m (6.6 ft). 1 2 2 m (6.6 ft) 1 3 HALO 2000 SERIES or HALO 3000 SERIES radar Conventional pulse radar or another HALO 2000 SERIES or HALO 3000 SERIES radar HALO 20, 20+ or 24 dome radar 2 m (6.6 ft) 1 2 3 Note: Possible interference can be reduced using the radars sector blanking setting on your multi-

function display. Power boat installations If possible, make sure the mounting location gives your radar a clear view all around the vessel. PAGE | 13 If you install your HALO radar on a power boat with a steep planing angle, it is recommended you tilt the radar angle down at the front. Note: Optional 4 base wedges are available from third-party suppliers. Considerations for roof mounting When deciding a suitable mounting location for your HALO radar, be aware that the vertical radar beam extends to 25 either side of horizontal, with 50% of the emitted energy projecting in a beam 12.5 either side of horizontal. If the radar beam cannot clear the roof line, this decreases the performance of the radar. Depending on the size of the hard top of the vessel, we recommend you elevate the antenna to ensure the radar beams clear the roof line. Possible performance loss If you mount your HALO radar directly on to a large hard top, the radars performance could suffer as the emitted energy is either reflected or absorbed by the hard top. 5 2 1 5

. 2 1 25% of energy 50% of energy y g r e n 5 % o f e 2 PAGE | 14 Good performance Raising the radar off the hard top allows most of the radar beam to clear the hard top. Best performance For best performance, the radar should be positioned to allow the full beam to clear the superstructure of the vessel. Note: If the mounting surface is made of metal, you must elevate the radar so the beam has complete clearance, otherwise its performance will be severely impaired. To calculate the antenna height for best performance, first measure the distance (A) from the installation location of the radar to the furthest forward corner of your vessels hard top. A A A PAGE | 15 For every increase of 200 mm (7.9) of hard top distance over 1.8 m (6.0), increase the height of the antenna by 46 mm (1.8). 2 5 1.8 m (6 ft) 2.0 m (6.5 ft) 2.2 m (7.2 ft) 2.4 m (7.8 ft) 2.6 m (8.5 ft) 2.8 m (9.1 ft) 3.0 m (9.8 ft)

(1.81")

(3.62")

(5.43") 46 mm 92 mm 138 mm

(7.24")

(9.06")

(9.69") 184 mm 230 mm 276 mm PAGE | 16 HARDWARE MOUNTING Install the RI-50 radar interface module Install the RI-50 in a dry location away from spray, rain, drips, condensation or excessive heat. The mounting position should be easily accessible. Always mount the RI-50 vertically, with the cable entry points facing downwards. This helps with cooling and helps prevent any water from entering the cable grommets. Ensure there is enough unobstructed space above and below the RI-50 to ensure it cools adequately and the ambient temperature does not exceed 55C (131F). If overheating is a concern, consider additional ventilation, such as a vent or extraction fan. Warning: Inadequate ventilation and subsequent overheating of the unit may cause unreliable operation and reduced service life. The RI-50 must be located where it can easily connect to the vessels ground connection, the pedestal interconnection cable and the power cable. Use fasteners suited to the mounting surface material. If you are using the supplied self-tapping screws with a soft material like plywood, use a 2.3 mm to 2.8 mm (3/32) drill bit. For hard materials like GRP, acrylic and hardwoods, use a 2.9 mm (7/64) drill bit. If the material is too thin for the self-

tapping screws, reinforce it or use machine screws, nuts and washers. Use only 304 or 316 stainless steel fasteners. Mark the screw locations using RI-50 box as a template, and drill pilot holes. PAGE | 17 Run the interconnection cable The interconnection cable is 10.5 mm (0.4) in diameter. The 14-pin connector end of the cable connects to the pedestal. The RJ45 connector connects to the RI-50 radar interface module. 1 Drill a 14 mm hole to pass the RJ45 connector from the pedestal to the RI-50, or a 24 mm (0.95) hole to pass the 14-pin connector from the RI-50 to the pedestal. 2 To protect the connectors, especially the RJ45 connector, when pulling the cable through the vessel, connect a mouse line to the outer jacket of the interconnection cable so the strain of pulling is transferred to the strong outer jacket. 3 If there is enough clearance, use a small cable tie to secure the mouse line to the outer jacket. 4 Tape the wires and the RJ45 connector to the mouse line so they do not get caught and bend backwards. C A B B A B C Mouse line Electrical tape Cable tie 5 Carefully pull the interconnection cable through the vessel so it runs between the RI-50 radar interface module and your chosen pedestal location. Install the pedestal Warning: Leave the waveguide protection cap on the pedestal while you mount it to your vessel. You should only remove the cap just before you fit the antenna to the pedestal. Bolts and washers The eight hex head bolts supplied are suitable for surfaces up to 25 mm (1) in thickness. Use the 4 x M12 x 35 mm (1.4) for a surface thickness from 5 mm (0.2) up to 13 mm (0.5). Use the 4 x M12 x 50 mm (2.0) for a surface thickness from 13 mm (0.5) up to 25 mm (1). If using longer bolts, ensure they are marine-grade stainless steel and allow for a minimum of 12 mm (0.3) and maximum of 20 mm (0.7) of thread engagement in base of pedestal. Use a flat washer and a spring washer for each bolt. Important: Apply a light coating of the supplied Tef-Gel or other suitable nickel- or PTFE-based lubricant to the mounting bolts to prevent galling and corrosion. PAGE | 18 If you are installing the pedestal onto a steel surface, also use the supplied plastic isolating washers. Surface mount: rear cable connection 1 Place the mounting template in your desired installation location, observing the correct orientation. Note: You can compensate for any minor deviations in orientation later by using the radars bearing alignment setting on your multi-function display. 2 Check the location has enough room for the antenna to rotate. 3 Tape the template securely in place. PAGE | 19 4 Drill pilot holes, then use a 13 mm (0.5) drill bit to drill the four holes where shown on the mounting template. 5 Remove the mounting template . 6 Apply the supplied Tef-Gel anti-corrosion gel to the four feet of the pedestal. 7 Lift the pedestal using the supplied lifting strap. Warning: Do not lift the pedestal with the antenna attached. 8 Lower the pedestal carefully so its mounting holes align with the drilled holes in the vessel. 9 Place a flat washer and spring washer onto each bolt. Note: If you are installing the pedestal onto a steel surface, also use the supplied plastic isolating washers. 10 Apply the Tef-Gel anti-corrosion gel to the threads of each bolt. PAGE | 20 11 Insert the bolts through the drilled holes and into the pedestals threaded mounting holes. Tighten the bolts securely. Note: The torque settings for the mounting bolts are 30 N.m 40 N.m (22.1 lb-ft 39.5 lb-ft). 12 Connect the 14-pin end of the interconnection cable to the pedestal. Take care to align the connector correctly to avoid bending the pins. Secure the locking collar by rotating clockwise until it clicks. PAGE | 21 Pole or tower mount: discreet cable connection The interconnection cable can be optionally connected underneath the pedestal by moving the 14-pin connector at the back of the pedestal to a bracket underneath the pedestal. 1 Remove the retaining nut and pull out the connector. 2 Remove the blanking plug from the bracket underneath the pedestal. 3 Insert the blanking plug where the connector used to be. 4 Re-route the connector to the bracket and secure it with the retaining nut. PAGE | 22 5 Connect the 14-pin end of the interconnection cable to the pedestal. Take care to align the connector correctly to avoid bending the pins. Secure the locking collar by rotating clockwise until it clicks. 6 Apply the supplied Tef-Gel anti-corrosion gel to the four feet of the pedestal. 7 Lower the pedestal so its mounting holes align with the drilled holes in the mounting plate. 8 Place a flat washer and spring washer onto each bolt. 9 Apply the Tef-Gel anti-corrosion gel to the threads of each bolt. 10 Insert the bolts through the drilled holes and into the pedestals threaded mounting holes. Tighten the bolts securely. Note: The torque settings for the mounting bolts are 30 N.m 40 N.m (22.1 lb-ft 39.5 lb-ft). Fit the antenna to the pedestal Warning: Do not operate the radar without the antenna connected. 1 Remove the waveguide protection cap from the pedestal and the waveguide protection label from the underside of the antenna. Note: The cap and label prevent contaminants from entering the waveguide. You should only remove these covers just before you fit the antenna to the pedestal. PAGE | 23 2 On the antenna, check the sealing ring is correctly positioned in the groove around the waveguide. 3 Apply the supplied Tef-Gel anti-corrosion gel to the entire length of each of the four antenna studs. Note: If black, isolating washers are factory fitted at the top of the antenna studs, do not remove. 4 Carefully lower the antenna on to the pedestal. Note: The antenna can only fit one way. x 4 5 Place a flat washer then a spring washer followed by a dome nut on to each of the antenna studs. Note: If black, isolating washers are factory fitted on the underside of the stud holes, do not remove. PAGE | 24 6 Tighten the dome nuts using a socket and torque wrench to 15 N.m (11 lb-ft). Note: Using a socket and torque wrench minimizes the risk of damaging the powder coated surface of the pedestal. PAGE | 25 WIRING RI-50 circuit board All wiring connections, except GND, are made inside the RI-50 interface box. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD Connector Description CASE / SHIP GND Alternative chassis ground connection. SUPPLY 12 or 24 V DC input 12 volt system limits 10.8 V DC to 15.6 V DC 24 volt system limits 20 V DC to 31.2 V DC NETWORK / MFD Connects the radar to the multi-function display. AUX POWER CONTROL 12/24V - 24V ONLY Inputs for the antenna park brake and remote power functions. Note: The TxSync and TxSync+ inputs are reserved for future functionality. Switch that sets the radars power to:

Always ON (the radar turns on when power is applied to the radars main power connector), or POWER CONTROLLED BY AUX REMOTE (the radar turns on when a remote multi-function display or power control switch is turned on). Switch that sets to:

12/24V (default), or 24V ONLY (select to protect a 24V battery system from over discharge) SCANNER Input for receiving Ethernet data from the pedestal and sending control signals. SCANNER POWER 2-way and 4-way connectors that provide 50 V DC up to the pedestal and power for the park brake. PAGE | 26

Run the cables Warning: The pedestal has a service mode switch, which disables power supply to the radar and stops the antenna rotating during maintenance and service. 1 Check the service mode switch at the back of the pedestal is set to 0 (power supply disabled). 2 Remove the circuit board cover from the RI-50 by unscrewing the six retaining screws. 3 Remove the grommet retaining clip. 4 Remove the rubber grommets. 5 Line the following cables up so they face their respective connector on the circuit board:

Power cable Ethernet adapter cable Pedestal interconnection cable Any AUX wires for the remote power and antenna park brake functions PAGE | 27 6 Pass the cables through the rubber grommets and into the RI-50. For cables with connectors, you need to cut a slit between the hole and edge of the grommet. Connect the interconnection cable To receive Ethernet data from the radar, connect the RJ45 connector end of the interconnection cable to the SCANNER connector on the circuit board. To provide power to the radar and park brake, connect the six wires of the interconnection cable to the 4-way and 2-way SCANNER POWER connectors on the circuit board, matching the color-coded stickers on the connectors with the wire colors. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD PAGE | 28 If you ever need to replace or refit the 8-pin RJ45 connector on the interconnection cable, use a RJ45 crimping tool and wire as follows:

8 1 Pin Wire color 1 2 3 4 5 6 7 8 White/orange Orange White/green Blue White/blue Green White/brown Brown If you need to test the 14-pin connector on the interconnection cable, it is wired as follows:

Pins on pedestal Pins on cable Pin Wire color 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Black Red Yellow Drain Orange Blue White/blue Pedestal power DC (-) Pedestal power DC (+) Park angle retention Tinned wire Pedestal power DC (+) RJ45 pin 4 RJ45 pin 5 White/brown RJ45 pin 7 Brown RJ45 pin 8 White/green RJ45 pin 3 Blue Pedestal power DC (-) White/orange RJ45 pin 1 Green Orange RJ45 pin 6 RJ45 pin 2 Connect the power cable The power supply for the radar is connected to the RI-50 interface module. Depending on radar power demand, the RI-50 can draw up to 20 A average (20 A nominal, 25 A peak) from both 12 and 24 V DC power systems. The RI-50 is protected against reverse polarity, over-voltage and under-voltage. The RI-50 must be connected via a dedicated fuse/circuit breaker rated at 25 A for either 12 or 24 V DC systems. The fuse/circuit breaker should be labeled accordingly. The further away the power supply, the thicker the cable you need. Voltage Cable length 0-2 m

(0-6.6 ft) 4 mm2

(12-AWG) 1.5 mm2

(16-AWG) 12 V DC 24 V DC Notes:

2-3 m

(6.6-9.8 ft) 3-5 m

(9.8-16.4 ft) 5-7.5 m

(16.4-24.6 ft) 7.5-12 m

(24.6-39.4 ft) 6 mm2

(10-AWG) 1.5 mm2

(16-AWG) 10 mm2

(8-AWG) 2.5 mm2

(14-AWG) 16 mm2

(6-AWG) 4 mm2

(12-AWG) 25 mm2

(4-AWG) 6 mm2

(10-AWG) Above values in mm2 = area of copper conductor. Stranded core cables are recommended. Conductor sizes greater than 10 mm2 (8-AWG) require a short length of thinner cable (6 mm2 10-AWG) to connect into the RI-50 screw terminals. PAGE | 29 1 Strip away approximately 10 mm (0.4) of insulation at the end of each wire. 2 Unscrew the terminal screw from the positive input SUPPLY connector (identified by the + sign) on the RI-50 circuit board. Insert the bare end of the positive wire into the positive input connector to make a connection. 3 4 Tighten the terminal screw to hold the positive wire in place. Gently pull the positive wire to ensure it is secured. 5 Repeat this process to connect the negative wire to the negative input SUPPLY connector 6

(identified by the sign). If you have a 24V battery system you want to protect from over discharge, change the 12/24V switch to 24V ONLY. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD _

12 -24 V DC Ground the RI-50 You can ground the RI-50 using the ground terminal on the underside of the case. The chassis ground is DC isolated from power (ve) to eliminate the risk of galvanic corrosion. It is recommended that the RI-50 ground is connected to the vessels bonded ground or a non-

bonded RF ground at the closest possible location, using 12 AWG wire (or thicker). PAGE | 30 Alternatively, you can ground the RI-50 using the CASE / SHIP GND spade terminal on the circuit board. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD Activate remote power control The RI-50 has an optional remote power control mode that enables a compatible multi-function display or ignition switch to control the power state of the radar. When the display or switch is turned on, the radar will turn on. To use the remote power control function:

1 Move the power control switch from Always ON (indicated by ON on the switch itself) to POWER CONTROLLED BY AUX REMOTE (indicated by 1 on the switch). 2 Apply +V DC (5 V DC - 32 V DC) from a compatible multi-function display or ignition switch to the Remote input of the AUX connector. On a compatible multi-function display, this is the yellow wire in the power cable. If you are using a multi-function display to power on the radar, set it to master (refer to the power control function in the displays user manual for instructions). 3 Notes:

If the power control switch is moved back to Always ON, the power wire in the AUX Remote port is ignored. If the radar is turned off via remote power control while transmitting, the radar will auto park the antenna before shutting down. There must be a common battery -ve for all devices on the power control bus. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD PAGE | 31 The following illustration is an example of a system using remote power control:

1 3 2 4 POWER TRANSDUCER 1 TRANSDUCER 2 SPEED TEMPERATURE 1 TEMPERATURE 2 4 5

+ _ 6 1 2 3 4 5 6 HALO radar pedestal and antenna RI-50 radar interface module Multi-function display set to power control master Other Simrad devices with remote power control Power control bus DC power Activate antenna park HALO 2000 SERIES and HALO 3000 SERIES radars have the ability to stop rotating the antenna and hold it at a predetermined angle in relation to the vessels heading line. This park angle is set in the radars software on your multi-function display. In addition, there is a park angle retention feature which is a very low current electromagnetic brake that provides resistance for the antenna to maintain a parked angle against wind and movement when the radar is not powered. The park brake requires a continuous low current DC supply (10-32 V DC). This draws less than 100uA. To activate the antenna brake park function, connect a signal wire from the positive side of the power supply to the Park input on the AUX connector. PAGE | 32 RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD Connect the network cables An Ethernet network is used to distribute the radar data to compatible multi-function displays. The RI-50 is connected to the Ethernet network using the supplied Ethernet cable and Ethernet adapter cable (RJ45 male to 5-pin female, 150 mm (5.9)). RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD PAGE | 33 The RI-50 can be connected directly to any Simrad-compatible multi-function display or to a network switch such as an NEP-2. 1 3 2 4 5 6 1 2 3 4 5 6 HALO radar pedestal and antenna RI-50 radar interface module Compatible multi-function displays NEP-2 or device with a built-in Ethernet switch Ethernet adapter Ethernet cable 1.8 m (6.0) Additional radar functions Additional radar functions such as VelocityTrack and ZoneTrack require good-quality, high-speed GPS position and heading data at 10 Hz or better. The GPS antenna must be mounted in a position that provides a clear view of the sky. A quality 10 Hz compass such as the Precision 9 is suitable for heading, however for the very best performance, a GPS compass such as Simrad HS75 or HS80A should be considered. The connected multi-function display sends NMEA 2000 position and heading data to the radar via the Ethernet connection. For radar chart overlay, an integrated GPS/compass sensor such as the Simrad GS25 is suitable, however the compass is not suitable for VelocityTrack and ZoneTrack as it does not have 10 Hz heading output. PAGE | 34 The following illustration is an example of a GPS and heading NMEA 2000 network:

2 1 3 5 4 6 7 7 _

12 V DC 8 T 9 T 1 2 3 4 5 6 7 8 9 HALO radar pedestal and antenna RI-50 radar interface module Compatible multi-function display NMEA 2000-compliant heading sensor (10 Hz minimum) GPS position sensor Ethernet cable Micro-C drop cables Network power 12 V DC Micro-C backbone (NMEA 2000) with terminators Start the radar When you finish connecting the cables to your RI-50, replace the cover on the circuit board and set the service mode switch on the back of the pedestal to l (power supply enabled). PAGE | 35 RI-50 LED indicator lights LED lights on the front of the RI-50 communicate its operating status. LED Color Indication Likely cause Power Green steady Power is applied and AUX remote power control input is active Normal operation Off No supply voltage or remote power control input is not active Check remote switch position. Ensure 12-24V switch is in correct position for supply voltage Fault Off Blue Purple The fault indicator shows existing conditions as steady colors and historic conditions as blink patterns. Re-power the RI-50 to clear a fault/warning indication. Normal Under or Over voltage Faults are defined as conditions that could cause damage to the equipment. Warnings indicate conditions that can cause the RI-50 to change the operating state of the radar, e.g. switching it to standby. The historic indication helps to identify the cause of intermittent problems. Low supply voltage to the RI-50 Over current including short circuits Input current > 20A or output current > 8A Red Over temperature Red blink Once the RI-50 returns to a stable state, either RUN or OFF, the fault LED will indicate its last condition. Warning .-.-

Warning .-. Warning ..-. Warning . Warning .. The internal temperature > 90C (194F). Caution: The heatsink case may be too hot to touch. Blink patterns indicate the type of fault or warning that is detected. The patterns repeat every 5s. Only one pattern displays at a time. Patterns consist of 1 to 4 blinks with each blink being short

(.) or long (-). Warnings start with short; faults start with long. There are no patterns with all long. Input voltage is unstable. Check the wiring and condition of the battery or power source. The AUX: Remote input was OFF, < 2.5V. Check the Remote Bypass switch or the external connection if used. Flat battery or very low input voltage, < 5V

(12V) or < 9V (24V). Check the input voltage. Low input voltage in 12V system, < 9.5V. The RI-50 switched to standby due to low input voltage. Could be engine cranking or other heavy load. Low input voltage in 24V system, < 19V. The RI-50 switched to standby due to low input voltage. Could be engine cranking or other heavy load. PAGE | 36 Warning ... Warning .... Fault -. Fault -.. Fault -... Fault -.-. Fault -.-

Fault --. Fault -..-

Status Green Normal operation Green/orange fast blinking Wrong or no radar connected Orange Pending shutdown Red Radar is off The RI-50 detected voltage on its output before it turned on. If the radar was only off for a short time, it is normal for there to be residual voltage. However, it can also indicate the output switch in the RI-50 has been damaged and needs repair. This will not stop the radar from working, but does mean the only remaining fault protection in the RI-50 is the 40A input fuse. High input voltage, > 34V. Check your input power source. Input voltages > 36.5V can damage the RI-50. Output voltage too high, > 54V. There is a risk of damage to the connected pedestal. Get the RI-50 checked. Average input current too high, > 20A. The RI-50 will retry up to 5 times before shutting down. Can be caused by low input voltage and/or excessive load from the pedestal. Average output current too high, > 8A. The RI-50 will retry up to 5 times before shutting down. Caused by excessive load from the pedestal. Typically indicates a short circuit on the pedestal cable. The output current was

> 10A. The RI-50 will retry up to 5 times before shutting down. Check the pedestal interconnection cable for damage. Over temperature, > 90C (194F). The RI-50 will re-start after cooling down. The RI-50 should be mounted as shown in the Hardware mounting section of this manual so that air can flow over the heatsink. Low input voltage and heavy pedestal load will increase heating. The wrong pedestal type has been connected. Pedestals designed to work with RI-12 interface modules (older) will not work with RI-50s and could be damaged. A software upgrade is required. Return the RI-50 for service. Output voltage > 45V. The radar will operate regardless of any fault or warning indication. Output voltage 16V to 45V. Check the pedestal is connected and it is a compatible model. Output voltage 16V to 45V. Typically the radar is given 30 seconds to prepare for shutdown. Output voltage <16V. Typically the output is off. PAGE | 37 Ethernet Green blink Successful communication with a multi-function display Normal operation. The LED activity increases with increasing Ethernet traffic. Off Communication not established Ethernet cable disconnected or faulty Ethernet cable to display. Fuse In the rare event that the non-replaceable fuse blows on your RI-50 circuit board, the BLOWN FUSE LED will light up while power is supplied to the RI-50. This indicates an internal fault and you will need to replace your RI-50 unit. Note: A blown fuse indicates an internal fault with your RI-50. It does not indicate a fault with the external wiring to the RI-50 or a fault with the radar pedestal. PAGE | 38 SETUP AND CONFIGURATION Make the following settings before use. Refer to the documentation supplied with your display unit to locate and adjust the settings. Radar source In a system with more than one radar, the device to configure is selected from here. Note: Radars that support dual radar mode are represented twice in the source list, with an A and a B suffix. Radar status Used to view information about your radar, such as the software version, serial number and operating hours. Antenna setup X-axis and Y-axis. Used to set the approximate position of the antenna on the vessel. This enables your vessel icon to be positioned correctly on the PPI. Height. Used to set the height of the antenna above the water line. Ensure the antenna height is set correctly, as it affects the sea clutter function. Do not set the height to zero. Span. Used to select the length of your antenna. Adjust bearing alignment Used to compensate for any slight misalignment of the pedestal during installation and to make sure targets and bearings taken with the electronic bearing line display accurately. The adjustment is made by aligning the heading marker on the screen with the center line of the vessel. Sidelobe suppression Used to increase the suppression if there are false targets appearing as arcs radiating from either side of an actual target (typically large structures such as steel hulled ships, container wharves and large buildings). By default this control is set to Auto, and normally should not need to be adjusted. Note: This setting should only be adjusted by experienced radar users. Target loss in harbor environments can occur if it is not adjusted correctly. Sector blanking Used to stop the radar transmitting in the direction of structures that could cause unwanted reflections or interference to appear on the radar image. Four sectors can be set, the bearing of which is measured from the bow of the vessel to the center line of the sector. Adjust open array park angle Used to set the resting position of the antenna relative to the heading line of the radar when the radar is set to standby. The antenna will stop rotating at the desired offset. Optionally, the antenna can be held in place against wind by connecting the antenna park wire. Note: When entering standby, the antenna may rotate multiple times before coming to rest. HALO light Used to control the brightness level of the blue LED accent light on the pedestal. There are four brightness levels. The level can only be adjusted when the radar is in standby mode. Warning: The pedestals blue accent lighting may not be approved for use in your boating location. Check your local boating regulations before turning the blue accent light on. Reset radar to factory defaults Used to reset the radars control settings (not installation settings) to their factory defaults. PAGE | 39 Error codes If you encounter an error code, power cycle the radar. If the error code reappears, refer to this list for guidance. Error code Description Recommendation 0x00000001 Radar saved settings corrupted Radar will revert to factory defaults. Re-enter your settings including installation settings. 0x0001000C Scanner not detected Check the pedestal interconnection cable connections. Power cycle the radar. Check input voltage. 0x0001000D Transmitter overheat (soft) Try changing to shorter ranges <6 NM. Switch to STBY. Allow unit cool. 0x0001000E Transmitter overheat (hard) Switch to STBY. Isolate power to the radar and contact service. 0x0001000F Signal processing error Unit should revert to STBY. Select transmit. If problem persists, power cycle the radar. 0x00010017 Scanner failure Contact service Power supply 0x00010010 Power supply overheating Switch to STBY. Allow unit to cool then retry. 0x00010011 Power supply voltage error Check pedestal interconnection cable for corrosion or damage. 0x00010012 Power supply overload Contact service 0x00010013 Power supply hardware fault Contact service 0x00010014 Power supply comms fault Contact service 0x00010019 Low battery voltage (Supply voltage low) Recharge and check supply voltage. Restart the radar. 0x00010016 LED Lighting fault Turn accent lighting off then retry. 0x00010018 Radar interface box fault Check LED status light. Check the pedestal interconnection cable for damage. Mechanical 0x00010001 Zero bearing sensor fault Contact service 0x00010002 Bearing sensor fault Contact service 0x00010015 Mechanical transmission Contact service fault 0x00010003 Motor drive fault Contact service 0x0001001A Motor or antenna has stalled Power down the radar. Check and clear antenna obstructions such as ice. PAGE | 40 UPGRADING HALO 3000 SERIES radars have higher current draw than HALO 3/4/6 SERIES radars due to a more powerful motor and higher transmit power. If you are upgrading from a HALO 3/4/6 SERIES radar to a HALO 3000 SERIES radar, you should change the interconnection cable. If you are upgrading from a HALO 3/4/6 SERIES radar to a HALO 2000 SERIES radar, you may use the existing interconnection cable but we recommend you inspect the condition of the connectors. Note: At the time of release, HALO 2000 SERIES and HALO 3000 SERIES radars work with Simrad GO XSR, GO XSE (9/12), NSS evo3, NSS evo3S, NSO evo3, NSO evo3S and NSO evo3S MPU systems. They also work with Simrad R2009 and R3016 radar control units. Record the old settings 1 Take note of the old radar settings, i.e. antenna height and span (if re-using the antenna), range offset, bearing alignment, sidelobe suppression, sector blanking and open array park angle. This will help you set up your new radar on the display unit. Isolate power to the radar 2 Turn off the circuit breaker or remove the fuse. Remove the old pedestal 3 Set the service mode switch at the back of the pedestal to 0 (power supply disabled). 4 Disconnect the interconnection cable from the pedestal. 5 Cover the 14-pin end of the interconnection cable to protect it from water and contaminants. 6 Use a socket and torque wrench to remove the dome nuts that hold the antenna to the pedestal. 7 Carefully lift the antenna off the pedestal. PAGE | 41 8 If re-using the antenna, cover the waveguide to protect it from water and contaminants. Remove the RI-12 9 Remove the circuit board cover from the RI-12 by unscrewing the six retaining screws. 10 Remove the grommet retaining clip. 11 Remove the rubber grommets. 12 Disconnect the power cable from the SUPPLY connector. 13 Unplug the RJ45 connector end of the interconnection cable from the SCANNER connector. Note: Keep wires connected to RJ45 connector. 14 Unplug the green 4-way connector from SCANNER POWER connector. Note: Keep wires connected to 4-way connector. 15 If used, unplug the AUX connector. Note: Keep wires connected to the AUX connector. 16 Unplug the Ethernet cable. 17 Unplug the Micro-C NMEA 2000 connector (This cable can be removed as it is not needed with the RI-50 interface module.) 18 Unscrew the RI-12 from its mounted location. 19 Remove the grounding wire if used. PAGE | 42 Install the RI-50 and new pedestal To install the RI-50 and your new HALO 2000 SERIES or HALO 3000 SERIES pedestal, follow the steps in the Hardware mounting and Wiring sections in this manual. Note: If you are re-using the original interconnection cable, only connect four wires to the 4-way SCANNER POWER connector on the circuit board. You wont use the 2-way connector. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD PAGE | 43 SPECIFICATIONS Type of approval FCC/IC/RED Type Certification HALO 2000 SERIES FCC ID: RAYHALO2000 (Navico Inc.) IC ID: 978B-HALO2000 (Navico Inc.) HALO 3000 SERIES FCC ID: RAYHALO3000 (Navico Inc.) IC ID: 978B-HALO3000 (Navico Inc.) EU RED: Emissions compliant to SM1541-4 (including -40 dB/dec future design objectives) and EN302-248 V2.1.1 Environmental Operating temperature

-25C to +55C (-13F to +131F) Relative humidity IEC60945 Exposed product Vibration IEC60945 Exposed product UV IEC60945 Exposed product Waterproofing IPX6 for the pedestal and antenna IPX5 for the RI-50 interface module Relative wind velocity HALO 2000 and HALO 3000 radars with 3 ft, 4 ft or 6 ft antenna have a wind rating of 80 knots at 48 rpm in both 24V and 12V systems. Power Power consumption HALO 2000 SERIES HALO 3000 SERIES 235 W (peak, 12V) at maximum wind velocity 380 W (peak, 24V) at maximum wind velocity 45-60 W (average) at zero wind velocity 11 W (average) in standby mode Refers to RI-50 input terminals 250 W (peak, 12V) at maximum wind velocity 395 W (peak, 24V) at maximum wind velocity 45-75 W (average) at zero wind velocity 11 W (average) in standby mode Refers to RI-50 input terminals DC input Radar system input 12 OR 24 V DC into the RI-50 12 V Systems 10.8 - 15 V DC 24 V Systems 20 - 31.2 V DC Pedestal voltage input is 50 V DC nominal generated by RI-50 Power up time 30-40 seconds from POWER OFF to TRANSMIT Physical Height 429 mm (16.88) with antenna mounted Antenna turning circle diameter 3 ft model: 3.75 ft / 1142 mm / 44.96 4 ft model: 4.73 ft / 1443 mm / 56.81 6 ft model: 6.72 ft / 2047 mm / 80.59 Component weights Pedestal Antenna 3 ft Antenna 4 ft Antenna 6 ft RI-50 10 m (33 ft) cable 20 m (66 ft) cable 30 m (100 ft) cable 20.3 Kg (44.8lb) 4.1 Kg (9.0 lb) 4.9 Kg (10.8 lb) 6.5 Kg (14.3 lb) 1.6 Kg (3.5 lb) 1.6 Kg (3.5 lb) 3.2 Kg (7.1 lb) 4.7 Kg (10.4 lb) PAGE | 44 Antenna Rotation speed 16 to 48 rpm depending on operating mode. Beam width Beam width vertical Plane of polarization 3 ft model: 2.4+/-10% (-3 dB width) 1.7 with Beam sharpening mode on 4 ft model: 1.8+/-10% (-3 dB width) 1.3 with Beam sharpening mode on 6 ft model: 1.2+/-10% (-3 dB width) 0.8 with Beam sharpening mode on 25 +/-10 % (-3 dB width) Horizontal polarization Sidelobe level 3 ft Below -23 dB max. (within 10) Below -30 dB max. (outside 10) Side lobe level 4 ft Below -23 dB max. (within 10) Below -30 dB max. (outside 10) Side lobe level 6 ft Below -23 dB max. (within 10) Below -30 dB max. (outside 10) Radar Peak power output HALO 2000 SERIES 50 W 10% under any transmit condition up to 10% duty cycle max HALO 3000 SERIES 130 W 10% under any transmit condition up to 13% duty cycle max Transmitter Solid state module with no long-term transmitter power degradation Transmitter frequency Pulse length/PRF and compression ratio Synthesized - Upper half of X-Band 9.390 - 9.495 GHz Pulse length: 0.04 usec Chirp length: 2-64 usec Chirp bandwidth: 2-48 MHz Up to 1 pulse and 4 chirps in a burst with burst repetition rate of 500-

3000Hz. Range and mode dependent. Effective pulse compression ratio less than 150 in all modes. Instrumented range HALO 2000 SERIES (all antenna sizes) 72 nm HALO 3000 SERIES (all antenna sizes) 96 nm SART/RACON triggering Yes trigger distance: about 1nm max weather, sea state, and SART position dependent Duplexer Circulator and isolator LNA IF section GaAs front-end Center frequency: 31.25 MHz Bandwidth: 50 MHz max.* A/D; 16 bit 125 MSPS

*Narrower bandwidths defined by signal processing Noise figure 5 dB (Min) at antenna input Compass safe distance Pedestal RI-50 Standard compass: 1.0 m (3.3 ft) Steering compass: 0.5 m (1.6 ft) Standard compass: 0.1 m (0.33 ft) Steering compass: 0.1 m (0.33 ft) PAGE | 45 Other Communication ports Transmit synchronization Ethernet 10/100 Base-T RJ-45 for radar data and control RS-422 output Remote power on Yes Antenna park hold Yes (while radar is unpowered) Motor Brushless with solid state commutation with electromagnetic braking for parking. Interconnecting cable Available in 10 m (33 ft), 20 m (66 ft), 30 m (100 ft) lengths. 20 m (66 ft) length cable included with unit. Options for cable to exit from rear of pedestal or pole mount. 3G/4G or HALO 3/4/6 SERIES interconnection cables can be used with the HALO 2000 SERIES only. PAGE | 46 DRAWINGS RI-50 213.0 mm (8.39") 195.0 mm (7.68")

4 7

. 7

m m 5

. 6 9 1

4 6

. 3

m m 5

. 2 9

9 3

. 3

m m 2

. 6 8

6 2

. 3

m m 7

. 2 8 PAGE | 47 Pedestal and antennas 429 mm (16.88") 135 mm (5.31") 294 mm (11.57") 264 mm (10.39")

8 2

. 7

m m 5 8 1 1 4

. 4 4

m m 8 2 1 1 8 3

. 6 5

m m 2 3 4 1 8 2

. 0 8

m m 9 3 0 2

t f 0 7

. 3 t f 0 7

. 4 t f 9 6

. 6 t f t f t f 3 4 6

7 2

. 8

m m 0 1 2

5 3

. 3 1

m m 9 3 3

9 6

. 6

m m 0 7 1

6 7

. 2 1

m m 4 2 3 PAGE | 48 Antenna turning circle diameters m / 44.96"

m / 56.81"

m / 80.59"

3.75 ft / 1142 m 4.73 ft / 1443 m 6.72 ft / 2047 m 3 ft 4 ft 6 ft PAGE | 49 PARTS LIST 000-15762-001 HALO 2000 SERIES pedestal 000-15766-001 HALO 3000 SERIES pedestal 000-11464-001 3 ft antenna 3.70 ft / 1128 mm / 44.41 000-11465-001 4 ft antenna 4.70 ft / 1432 mm / 56.38 000-11466-001 6 ft antenna 6.69 ft / 2039 mm / 80.28 000-15757-001 RI-50 radar interface module 000-15767-001 Interconnection cable 10 m (33 ft) 000-15768-001 Interconnection cable 20 m (65.6 ft) 000-15769-001 Interconnection cable 30 m (98.5 ft) 000-11246-001 Adapter cable: yellow Ethernet female to RJ45 male. 150 mm (5.9) PAGE | 50 PAGE | 51

1 0 0

6 4 8 2 1

8 8 9

www.simrad-yachting.comReg. U.S. Pat. & Tm. Off, and common law marks.Visit www.navico.com/intellectual-property to review the global trade-mark rights and accreditations for Navico Holding AS and other entities.

HALO 2000 Series and HALO 3000 Series pulse compression radars INSTALLATION MANUAL ENGLISH www.simrad-yachting.com PAGE | 2 PREFACE Disclaimer This product is not a substitute for proper training and prudent seamanship. It is the owners sole responsibility to install and use the equipment in a manner that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing maritime safety practices. Navigational features that appear in this guide are not a substitute for proper training and prudent seamanship. They do not replace a human navigator and SHOULD NOT be relied on as a sole or primary source of navigation. It is the operators sole responsibility to use more than one navigational method to ensure the route suggested by the system is safe. NAVICO HOLDING AS AND ITS SUBSIDIARIES, BRANCHES AND AFFILIATES DISCLAIM ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY VIOLATE THE LAW. This manual represents the product as at the time of printing. Navico Holding AS and its subsidiaries, branches and affiliates reserve the right to make changes to the product and/or specifications at any time without notice. Please contact your nearest distributor if you require any further assistance. Governing language This statement, any instruction manuals, user guides and other information relating to the product

(Documentation) may be translated to, or has been translated from, another language (Translation). In the event of any conflict between any Translation of the Documentation, the English language version of the Documentation will be the official version of the Documentation. Copyright Copyright 2022 Navico Holding AS. Warranty The warranty card is supplied as a separate document. In case of any queries, refer to the brand website of your display or system:

www.simrad-yachting.com. Declarations and conformance This equipment is intended for use in international waters as well as coastal sea areas administered by countries of the E.U. and E.E.A. Compliance statements Declarations The relevant declarations of conformity are available on the following website within the radars documentation section: www.simrad-yachting.com. United Kingdom Simrad HALO 2000 Series and HALO 3000 Series pulse compression radars comply with UKCA under The Radio Equipment Regulations 2017. The Simrad HALO RI-50 interface module complies with UKCA under The Electromagnetic Compatibility Regulations 2016. Europe Simrad HALO 2000 Series and HALO 3000 Series pulse compression radars comply with CE under RED Directive 2014/53/EU. The Simrad HALO RI-50 interface module complies with CE under EMC Directive 2014/30/EU. PAGE | 3 United States of America THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Warning: Navico is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the users authority to operate the equipment. RF emissions notice This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This devices antenna must be installed in accordance with provided instructions, and it must be operated with a minimum spacing of 849.06 cm (27.856 ft) for the HALO 3000 Series and 564.96 cm (18.5354 ft) for the HALO 2000 Series between the antenna and a persons body

(excluding extremities of hands, wrist and feet). Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help. Canada English This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Franais Le prsent appareil est conforme aux Innovation, Sciences et Dveloppement conomique Canada

(ISDE) applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes : (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Innovation, Science and Economic Development Canada (ISED) statement English Under ISED regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. The radio transmitters, 978B-HALO2000 and 978B-HALO3000, have been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. PAGE | 4 Franais Conformment la rglementation dInnovation, Sciences et Dveloppement conomique Canada

(ISDE), le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal

(ou infrieur) approuv pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpassepas lintensit ncessaire ltablissement dune communication satisfaisante. Les prsents metteurs radio, 978B-HALO2000 et 978B-HALO3000, ont t approuvs par Innovation, Sciences et Dveloppement conomique Canada (ISDE) pour fonctionner avec les types dantenne numrs ci-dessous et ayant un gain admissible maximal et limpdance requise pour chaque type dantenne. Les types dantenne non inclus dans cette liste, ou dont le gain est suprieur au gain maximal indiqu, sont strictement interdits pour lexploitation de lmetteur. HALO antennas Description Max. permissible antenna gain (dBi) Impedance 000-11464-001 Antenna, 3ft, HALO 26 50 Ohm (WR-90 waveguide) 000-11465-001 Antenna, 4ft, HALO 27.2 50 Ohm (WR-90 waveguide) 000-11466-001 Antenna, 6ft, HALO 29 50 Ohm (WR-90 waveguide) Radio frequency (RF) safe distances Figures in the table below show the radio frequency radiation safe distance for an operating antenna is within the antennas turning circle. Irrespective, users should stay well outside the turning circle of the antenna to avoid injury through physical impact as it spins. Note: These safe distances are based on conservative, near field, average power calculations. They are being tested by an independent laboratory and will be updated once test results are available. System 100 W / m2 occupational safe distance 10 W / m2 public safe distance HALO 2000 Series radars 0.4 m (1.2 ft) HALO 3000 Series radars 0.5 m (1.6 ft) 1.5 m (4.9 ft) 2.0 m (6.6 ft) Trademarks Reg. U.S. Pat. & Tm. Off, and common law marks. Visit www.navico.com/intellectual-property to review the global trademark rights and accreditations for Navico Holding AS and other entities. Navico is a registered trademark of Navico Holding AS. Simrad is a registered trademark of Kongsberg Maritime AS, licensed to Navico Holding AS. HALO is a registered trademark of Navico Holding AS. VelocityTrack is a trademark of Navico Holding AS. ZoneTrack is a trademark of Navico Holding AS. Precision is a trademark of Navico Holding AS. GO is a trademark of Navico Holding AS. NSS evo3 is a trademark of Navico Holding AS. NSS evo3S is a trademark of Navico Holding AS. NSO evo3 is a trademark of Navico Holding AS. NSO evo3S is a trademark of Navico Holding AS. NSO evo3S is a trademark of Navico Holding AS. XSE is a trademark of Navico Holding AS. XSR is a trademark of Navico Holding AS. R2009 is a trademark of Navico Holding AS. PAGE | 5 R3016 is a trademark of Navico Holding AS. NMEA 2000 is a trademark of the National Marine Electronics Association. About this manual This manual is a reference guide for installing the Simrad HALO 2000 Series and HALO 3000 Series pulse compression radars. It does not cover basic background information about how equipment such as radars, echosounders and AIS work. Such information is available from our website: www. support.simrad-yachting.com. Intended audience This manual assumes the reader has basic knowledge about this type of equipment with regards to:

installation work to be carried out nautical terminology and practices. Translated manuals Translated versions of this manual can be found on the website: www.simrad-yachting.com. PAGE | 6 CONTENTS 8Introduction 8Warnings 9Check the parts 9Pedestal 10Antenna 10RI-50 radar interface module 11Tools required 12Installation guidelines 12What not to do 13Compass safe distance 13Multi-radar installations 13Power boat installations 14Considerations for roof mounting 17Hardware mounting 17Install the RI-50 radar interface module 18Run the interconnection cable 18Install the pedestal 19Surface mount: rear cable connection 22Pole or tower mount: discreet cable connection 23Fit the antenna to the pedestal 26Wiring 26RI-50 circuit board 27Run the cables 28Connect the interconnection cable 29Connect the power cable 30Ground the RI-50 31Activate remote power control 32Activate antenna park 33Connect the network cables 34Additional radar functions 35Start the radar 36RI-50 LED indicator lights 38Fuse 39Setup and configuration 39Radar source 39Radar status 39Antenna setup 39Adjust bearing alignment 39Sidelobe suppression 39Sector blanking 39Adjust open array park angle 39HALO light 39Reset radar to factory defaults 40Error codes 41Upgrading 41Record the old settings 41Isolate power to the radar 41Remove the old pedestal 42Remove the RI-12 43Install the RI-50 and new pedestal 44Specifications 47Drawings 47RI-50 48Pedestal and antennas 49Antenna swing circle diameters 50Parts list PAGE | 7 INTRODUCTION This manual explains how to install the latest generation of HALO open array, pulse compression radars the HALO 2000 Series and HALO 3000 Series. This manual should be used in conjunction with the installation manual provided with your multi-

function display. It is written for professional marine technicians, installation technicians and service technicians. Dealers may use information contained in this document. HALO 2000 Series and HALO 3000 Series radars combine the best characteristics of traditional pulse and FMCW broadband radar systems. Pulse compression technology provides an unprecedented mix of long and short detection range, high target definition, and minimal clutter. Solid state technology means minimal warm-up time and maximum ocean-going reliability. This latest generation of HALO open array radars incorporate updated hardware and mechanical design improvements that deliver increased power, improved long-range target detection performance and more system reliability. HALO 2000 Series and HALO 3000 Series radar systems consist of a pedestal, antenna, RI-50 radar interface module and connection cables. A supplied Ethernet network cable connects the RI-50 radar interface module to the navigation Ethernet network. Notes:

HALO 2000 Series and HALO 3000 Series radar systems are available with antennas in three sizes: 3 ft, 4 ft and 6 ft. At the time of release, HALO 2000 Series and HALO 3000 Series radars work with Simrad GO XSR, GO XSE (9/12), NSS evo3, NSS evo3S, NSO evo3, NSO evo3S and NSO evo3S MPU systems. They also work with Simrad R2009 and R3016 radar control units. Warnings Use the radar at your own risk. Your radar is designed as a navigation aid. Always compare the navigation information received from your radar with data from other navigation aids and sources. When a conflict arises between the navigation data from your radar and data from other navigation aids, make sure you resolve the conflict before proceeding with navigation. A CAREFUL NAVIGATOR NEVER RELIES ON ONLY ONE METHOD TO OBTAIN NAVIGATION INFORMATION. International Regulations for Preventing Collisions at Sea mandate that when radar is on a vessel, the radar must be used at all times, regardless of weather conditions or visibility. Numerous court decisions have ruled that the radar must be used, and the radar operator must know all operational aspects of radar performance. Otherwise they will face a greater risk of liability if an accident occurs. High current, stored and microwave energy hazard. Technicians must exercise extreme care when working with the unit. ALWAYS disconnect from the power source before removing the cover. Some capacitors may take several minutes to discharge, even after switching off the radar. Before touching any high voltage components, ground them with a clip lead. The radars blue 4-level static accent pedestal lighting may not be approved for use in your boating location. Please check your local boating regulations before turning the blue accent lights ON. The microwave energy radiated by a radar antenna is harmful to humans, especially the eyes. NEVER look directly into an open waveguide or into the path of radiation from an enclosed antenna. Disconnect from the power source or use the service mode switch on the back of the pedestal whenever you need to work on the antenna or other equipment in the beam of the radar. PAGE | 8 CHECK THE PARTS Pedestal 1 2 3 4 5 e d c b a 6 7 8 Radar pedestal Interconnection cable 20 m (65 ft). Other lengths are available from your nearest Simrad dealer. Lifting strap Blanking plug (used when the interconnection cable is connected underneath the pedestal. Blanking plug is fitted underneath the pedestal when manufactured.) Tef-Gel anti-seize, anti-corrosion gel Mounting bolts and washers a) Bolts, hex head, M12 x 35 mm, 316 s/s b) Bolts, hex head, M12 x 50 mm, 316 s/s c) Flat washer, M12 x 36 x 3, 316 s/s d) Spring washer, M12, 316 s/s e) Plastic isolating washer, M12 x 38 x 4 x 4 x 4 x 4 x 8 Mounting template This manual 1 2 3 4 5 6 7 8 PAGE | 9 Antenna 1 4 3 2 1 2 3 4 Radar antenna 3 ft model: 3.70 ft / 1128 mm / 44.41 4 ft model: 4.70 ft / 1432 mm / 56.38 6 ft model: 6.69 ft / 2039 mm / 80.28 Dome nuts, M8, 316 s/s Spring washers, M8, 316 s/s Flat washers, M8 x 16 x 1.2, 316 s/s x 4 x 4 x 4 RI-50 radar interface module 1 2 5 6 4 3 7 1 2 3 4 5 6 7 RI-50 radar interface module 4-way connector for the pedestal interconnection cable 2-way connector for the pedestal interconnection cable Connector for Aux in (remote power and antenna park brake) Mounting screws, Phillips pan head, No. 6 x 45 mm, s/tap, 304 s/s x 4 Ethernet adapter RJ45 male to 5-pin female 150 mm (5.9) Ethernet cable 1.8 m (6.0) PAGE | 10 TOOLS REQUIRED 1 2 3 4 5 6 7 8 9 10 11 1 2 3 4 5 6 7 8 9 10 11 Drill Torque wrench 19 mm socket 13 mm socket Drill bit 13 mm (0.5) Sharp knife Screwdriver (Pozidriv, PZ2) for RI-50 mounting screws Screwdriver (Phillips, #1) for RI-50 circuit board cover screws Screwdriver (flat head, 4 mm) for SUPPLY and SCANNER POWER connectors Screwdriver (flat head, 3 mm) for AUX connectors RJ45 crimping tool (if refitting/replacing the RJ45 connector) PAGE | 11 INSTALLATION GUIDELINES Warning: A radar should only be installed by a qualified marine technician, as improper installation poses risks to the installer, the public, and to the safety of the vessel. Warning: Before starting the installation or any maintenance on a HALO 2000 Series or HALO 3000 Series radar, make sure the service mode switch at the back of the pedestal is set to 0 (power supply disabled). There is a transmit interlock that prevents radar transmissions if the antenna is not rotating. However, a high voltage remains for a period of time after the system is turned off. If you are not familiar with this type of electronics, consult a trained service or installation technician before trying to service any part of the equipment. Installation includes:

hardware mounting electrical wiring configuring the display or network system to work with the radar adjusting the radar for proper performance. The radars ability to detect targets depends greatly on its location. The ideal location is high above the vessels keel line where there are no obstacles. A higher installation location improves the radars ranging distance, but it also increases the range around the vessel where targets cannot be detected and increases sea clutter pick up. When you are deciding on the location, consider the following:

The length of the 20 m (66 ft) interconnection cable supplied with the radar is usually sufficient. A longer 30 m (98 ft) cable is available. 30 m (98 ft) is the longest the cable that can be used. If the roof of the wheelhouse is the highest existing location, consider installing a radar mast or tower on which you can mount the radar. If you install the radar on the mast, position it on the forward side so there is a clear view to the front of the vessel. It is preferable to install the antenna parallel to the line of the keel. What not to do Do not install the radar too high, where its weight may compromise the stability of the vessel and degrade the radar picture over short ranges. Do not install the radar close to lamps or exhaust outlets. Heat, soot, and smoke emissions may degrade radar performance or cause a breakdown. Do not install the radar where a large obstruction (such as an exhaust stack) is at the same level as the beam. The obstruction is likely to generate false echoes and/or shadow zones. If there is no alternative location, use the radars sector blanking setting on your multi-function display. Do not install the radar close to the antennas of other equipment, such as direction finders, VHF antennas and GPS equipment, as it may cause interference. Do not install the radar where may be subjected to strong vibrations that could degrade its performance. Do not install the radar close to halyards or flags because the wind could wrap these around the antenna and jam it. PAGE | 12 Compass safe distance Do not install your HALO radar inside of the recommended safe distances of any navigation instruments such as the magnetic compass and chronometer. The minimum distance to install the pedestal near the vessels compass is STD 1.0 m (3.3 ft), Steer 0.5 m (1.6 ft). W N S STD 1.0 m (3.3 ft) Steer 0.5 m (1.6 ft) E The minimum distance to install the RI-50 near the vessels compass is STD 1.0 m (3.3 ft). Multi-radar installations Do not install your HALO 2000 Series or HALO 3000 Series radar on the same horizontal beam plane as any other radar. Separate them vertically by at least 2 m (6.6 ft). 2 m (6.6 ft) 1 2 2 m (6.6 ft) 1 3 1 2 3 HALO 2000 Series or HALO 3000 Series radar Conventional pulse radar or another HALO 2000 Series or HALO 3000 Series radar HALO 20, 20+ or 24 dome radar Note: Possible interference can be reduced using the radars sector blanking setting on your multi-

function display. Power boat installations If possible, make sure the mounting location gives your radar a clear view all around the vessel. PAGE | 13 If you install your HALO radar on a power boat with a steep planing angle, it is recommended you tilt the radar angle down at the front. Note: Optional 4 base wedges are available from third-party suppliers. Considerations for roof mounting When deciding a suitable mounting location for your HALO radar, be aware that the vertical radar beam extends to 25 either side of horizontal, with 50% of the emitted energy projecting in a beam 12.5 either side of horizontal. If the radar beam cannot clear the roof line, this decreases the performance of the radar. Depending on the size of the hard top of the vessel, we recommend you elevate the antenna to ensure the radar beams clear the roof line. Possible performance loss If you mount your HALO radar directly on to a large hard top, the radars performance could suffer as the emitted energy is either reflected or absorbed by the hard top. 5 2 1 5

. 2 1 25% of energy 50% of energy y g r e n 5 % o f e 2 PAGE | 14 Good performance Raising the radar off the hard top allows most of the radar beam to clear the hard top. Best performance For best performance, the radar should be positioned to allow the full beam to clear the superstructure of the vessel. Note: If the mounting surface is made of metal, you must elevate the radar so the beam has complete clearance, otherwise its performance will be severely impaired. To calculate the antenna height for best performance, first measure the distance (A) from the installation location of the radar to the furthest forward corner of your vessels hard top. A A A PAGE | 15 For every increase of 200 mm (7.9) of hard top distance over 1.8 m (6.0), increase the height of the antenna by 46 mm (1.8). 2 5 1.8 m (6 ft) 2.0 m (6.5 ft) 2.2 m (7.2 ft) 2.4 m (7.8 ft) 2.6 m (8.5 ft) 2.8 m (9.1 ft) 3.0 m (9.8 ft)

(1.81")

(3.62")

(5.43") 46 mm 92 mm 138 mm

(7.24")

(9.06")

(9.69") 184 mm 230 mm 276 mm PAGE | 16 HARDWARE MOUNTING Install the RI-50 radar interface module Install the RI-50 in a dry location away from spray, rain, drips, condensation or excessive heat. The mounting position should be easily accessible. Always mount the RI-50 vertically, with the cable entry points facing downwards. This helps with cooling and helps prevent any water from entering the cable grommets. Ensure there is enough unobstructed space above and below the RI-50 to ensure it cools adequately and the ambient temperature does not exceed 55C (131F). If overheating is a concern, consider additional ventilation, such as a vent or extraction fan. Warning: Inadequate ventilation and subsequent overheating of the unit may cause unreliable operation and reduced service life. The RI-50 must be located where it can easily connect to the vessels ground connection, the pedestal interconnection cable and the power cable. Use fasteners suited to the mounting surface material. If you are using the supplied self-tapping screws with a soft material like plywood, use a 2.3 mm to 2.8 mm (3/32) drill bit. For hard materials like GRP, acrylic and hardwoods, use a 2.9 mm (7/64) drill bit. If the material is too thin for the self-

tapping screws, reinforce it or use machine screws, nuts and washers. Use only 304 or 316 stainless steel fasteners. Mark the screw locations using RI-50 box as a template, and drill pilot holes. PAGE | 17 Run the interconnection cable The interconnection cable is 10.5 mm (0.4) in diameter. The 14-pin connector end of the cable connects to the pedestal. The RJ45 connector connects to the RI-50 radar interface module. 1 Drill a 14 mm hole to pass the RJ45 connector from the pedestal to the RI-50, or a 24 mm (0.95) hole to pass the 14-pin connector from the RI-50 to the pedestal. 2 To protect the connectors, especially the RJ45 connector, when pulling the cable through the vessel, connect a mouse line to the outer jacket of the interconnection cable so the strain of pulling is transferred to the strong outer jacket. 3 If there is enough clearance, use a small cable tie to secure the mouse line to the outer jacket. 4 Tape the wires and the RJ45 connector to the mouse line so they do not get caught and bend backwards. C A B B A B C Mouse line Electrical tape Cable tie 5 Carefully pull the interconnection cable through the vessel so it runs between the RI-50 radar interface module and your chosen pedestal location. Install the pedestal Warning: Leave the waveguide protection cap on the pedestal while you mount it to your vessel. You should only remove the cap just before you fit the antenna to the pedestal. Bolts and washers The eight hex head bolts supplied are suitable for surfaces up to 25 mm (1) in thickness. Use the 4 x M12 x 35 mm (1.4) for a surface thickness from 5 mm (0.2) up to 13 mm (0.5). Use the 4 x M12 x 50 mm (2.0) for a surface thickness from 13 mm (0.5) up to 25 mm (1). If using longer bolts, ensure they are marine-grade stainless steel and allow for a minimum of 12 mm (0.3) and maximum of 20 mm (0.7) of thread engagement in base of pedestal. Use a flat washer and a spring washer for each bolt. Important: Apply a light coating of the supplied Tef-Gel or other suitable nickel- or PTFE-based lubricant to the mounting bolts to prevent galling and corrosion. PAGE | 18 If you are installing the pedestal onto a steel surface, also use the supplied plastic isolating washers. Surface mount: rear cable connection 1 Place the mounting template in your desired installation location, observing the correct orientation. Note: You can compensate for any minor deviations in orientation later by using the radars bearing alignment setting on your multi-function display. 2 Check the location has enough room for the antenna to rotate. 3 Tape the template securely in place. PAGE | 19 4 Drill pilot holes, then use a 13 mm (0.5) drill bit to drill the four holes where shown on the mounting template. 5 Remove the mounting template . 6 Apply the supplied Tef-Gel anti-corrosion gel to the four feet of the pedestal. 7 Lift the pedestal using the supplied lifting strap. Warning: Do not lift the pedestal with the antenna attached. 8 Lower the pedestal carefully so its mounting holes align with the drilled holes in the vessel. 9 Place a flat washer and spring washer onto each bolt. Note: If you are installing the pedestal onto a steel surface, also use the supplied plastic isolating washers. 10 Apply the Tef-Gel anti-corrosion gel to the threads of each bolt. PAGE | 20 11 Insert the bolts through the drilled holes and into the pedestals threaded mounting holes. Tighten the bolts securely. Note: The torque settings for the mounting bolts are 30 N.m 40 N.m (22.1 lb-ft 39.5 lb-ft). 12 Connect the 14-pin end of the interconnection cable to the pedestal. Take care to align the connector correctly to avoid bending the pins. Secure the locking collar by rotating clockwise until it clicks. PAGE | 21 Pole or tower mount: discreet cable connection The interconnection cable can be optionally connected underneath the pedestal by moving the 14-pin connector at the back of the pedestal to a bracket underneath the pedestal. 1 Remove the retaining nut and pull out the connector. 2 Remove the blanking plug from the bracket underneath the pedestal. 3 Insert the blanking plug where the connector used to be. 4 Re-route the connector to the bracket and secure it with the retaining nut. PAGE | 22 5 Connect the 14-pin end of the interconnection cable to the pedestal. Take care to align the connector correctly to avoid bending the pins. Secure the locking collar by rotating clockwise until it clicks. 6 Apply the supplied Tef-Gel anti-corrosion gel to the four feet of the pedestal. 7 Lower the pedestal so its mounting holes align with the drilled holes in the mounting plate. 8 Place a flat washer and spring washer onto each bolt. 9 Apply the Tef-Gel anti-corrosion gel to the threads of each bolt. 10 Insert the bolts through the drilled holes and into the pedestals threaded mounting holes. Tighten the bolts securely. Note: The torque settings for the mounting bolts are 30 N.m 40 N.m (22.1 lb-ft 39.5 lb-ft). Fit the antenna to the pedestal Warning: Do not operate the radar without the antenna connected. 1 Remove the waveguide protection cap from the pedestal and the waveguide protection label from the underside of the antenna. Note: The cap and label prevent contaminants from entering the waveguide. You should only remove these covers just before you fit the antenna to the pedestal. PAGE | 23 2 On the antenna, check the sealing ring is correctly positioned in the groove around the waveguide. 3 Apply the supplied Tef-Gel anti-corrosion gel to the entire length of each of the four antenna studs. Note: If black, isolating washers are factory fitted at the top of the antenna studs, do not remove. 4 Carefully lower the antenna on to the pedestal. Note: The antenna can only fit one way. x 4 5 Place a flat washer then a spring washer followed by a dome nut on to each of the antenna studs. Note: If black, isolating washers are factory fitted on the underside of the stud holes, do not remove. PAGE | 24 6 Tighten the dome nuts using a socket and torque wrench to 15 N.m (11 lb-ft). Note: Using a socket and torque wrench minimizes the risk of damaging the powder coated surface of the pedestal. PAGE | 25 WIRING RI-50 circuit board All wiring connections, except GND, are made inside the RI-50 interface box. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD Connector Description CASE / SHIP GND Alternative chassis ground connection. SUPPLY 12 or 24 V DC input 12 volt system limits 10.8 V DC to 15.6 V DC 24 volt system limits 20 V DC to 31.2 V DC NETWORK / MFD Connects the radar to the multi-function display. AUX POWER CONTROL 12/24V - 24V ONLY Inputs for the antenna park brake and remote power functions. Note: The TxSync and TxSync+ inputs are reserved for future functionality. Switch that sets the radars power to:

Always ON (the radar turns on when power is applied to the radars main power connector), or POWER CONTROLLED BY AUX REMOTE (the radar turns on when a remote multi-function display or power control switch is turned on). Switch that sets to:

12/24V (default), or 24V ONLY (select to protect a 24V battery system from over discharge) SCANNER Input for receiving Ethernet data from the pedestal and sending control signals. SCANNER POWER 2-way and 4-way connectors that provide 50 V DC up to the pedestal and power for the park brake. PAGE | 26 Run the cables Warning: The pedestal has a service mode switch, which disables power supply to the radar and stops the antenna rotating during maintenance and service. 1 Check the service mode switch at the back of the pedestal is set to 0 (power supply disabled). 2 Remove the circuit board cover from the RI-50 by unscrewing the six retaining screws. 3 Remove the grommet retaining clip. 4 Remove the rubber grommets. 5 Line the following cables up so they face their respective connector on the circuit board:

Power cable Ethernet adapter cable Pedestal interconnection cable Any AUX wires for the remote power and antenna park brake functions PAGE | 27 6 Pass the cables through the rubber grommets and into the RI-50. For cables with connectors, you need to cut a slit between the hole and edge of the grommet. Connect the interconnection cable To receive Ethernet data from the radar, connect the RJ45 connector end of the interconnection cable to the SCANNER connector on the circuit board. To provide power to the radar and park brake, connect the six wires of the interconnection cable to the 4-way and 2-way SCANNER POWER connectors on the circuit board, matching the color-coded stickers on the connectors with the wire colors. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD PAGE | 28

If you ever need to replace or refit the 8-pin RJ45 connector on the interconnection cable, use a RJ45 crimping tool and wire as follows:

8 1 Pin Wire color 1 2 3 4 5 6 7 8 White/orange Orange White/green Blue White/blue Green White/brown Brown If you need to test the 14-pin connector on the interconnection cable, it is wired as follows:

Pins on pedestal Pins on cable Pin Wire color 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Black Red Yellow Drain Orange Blue White/blue Pedestal power DC (-) Pedestal power DC (+) Park angle retention Tinned wire Pedestal power DC (+) RJ45 pin 4 RJ45 pin 5 White/brown RJ45 pin 7 Brown RJ45 pin 8 White/green RJ45 pin 3 Blue Pedestal power DC (-) White/orange RJ45 pin 1 Green Orange RJ45 pin 6 RJ45 pin 2 Connect the power cable The power supply for the radar is connected to the RI-50 interface module. The radar needs a 12 or 24 V DC supply capable of delivering 20 A for 12 V system and 10 A for 24 V system. The RI-50 is protected against reverse polarity, overvoltage and undervoltage. The RI-50 must be connected via a dedicated fuse/circuit breaker rated at 25 A for 12 V DC systems or 15 A for 24 V DC systems. The fuse/circuit breaker should be labeled accordingly. The further away the power supply, the thicker the cable you need. Voltage Cable length 0-2 m

(0-6.6 ft) 4 mm2

(12-AWG) 1.5 mm2

(16-AWG) 12 V DC 24 V DC Notes:

2-3 m

(6.6-9.8 ft) 3-5 m

(9.8-16.4 ft) 5-7.5 m

(16.4-24.6 ft) 7.5-12 m

(24.6-39.4 ft) 6 mm2

(10-AWG) 1.5 mm2

(16-AWG) 10 mm2

(8-AWG) 2.5 mm2

(14-AWG) 16 mm2

(6-AWG) 4 mm2

(12-AWG) 25 mm2

(4-AWG) 6 mm2

(10-AWG) Above values in mm2 = area of copper conductor. Stranded core cables are recommended. Conductor sizes greater than 10 mm2 (8-AWG) require a short length of thinner cable (6 mm2 10-AWG) to connect into the RI-50 screw terminals. PAGE | 29 1 Strip away approximately 10 mm (0.4) of insulation at the end of each wire. 2 Unscrew the terminal screw from the positive input SUPPLY connector (identified by the + sign) on the RI-50 circuit board. Insert the bare end of the positive wire into the positive input connector to make a connection. 3 4 Tighten the terminal screw to hold the positive wire in place. Gently pull the positive wire to ensure it is secured. 5 Repeat this process to connect the negative wire to the negative input SUPPLY connector 6

(identified by the sign). If you have a 24V battery system you want to protect from over discharge, change the 12/24V switch to 24V ONLY. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD _

12 -24 V DC Ground the RI-50 You can ground the RI-50 using the ground terminal on the underside of the case. The chassis ground is DC isolated from power (ve) to eliminate the risk of galvanic corrosion. It is recommended that the RI-50 ground is connected to the vessels bonded ground or a non-

bonded RF ground at the closest possible location, using 12 AWG wire (or thicker). PAGE | 30 Alternatively, you can ground the RI-50 using the CASE / SHIP GND spade terminal on the circuit board. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD Activate remote power control The RI-50 has an optional remote power control mode that enables a compatible multi-function display or ignition switch to control the power state of the radar. When the display or switch is turned on, the radar will turn on. To use the remote power control function:

1 Move the power control switch from Always ON (indicated by ON on the switch itself) to POWER CONTROLLED BY AUX REMOTE (indicated by 1 on the switch). 2 Apply +V DC (5 V DC - 32 V DC) from a compatible multi-function display or ignition switch to the Remote input of the AUX connector. On a compatible multi-function display, this is the yellow wire in the power cable. If you are using a multi-function display to power on the radar, set it to master (refer to the power control function in the displays user manual for instructions). 3 Notes:

If the power control switch is moved back to Always ON, the power wire in the AUX Remote port is ignored. If the radar is turned off via remote power control while transmitting, the radar will auto park the antenna before shutting down. There must be a common battery -ve for all devices on the power control bus. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD PAGE | 31 The following illustration is an example of a system using remote power control:

1 3 2 4 POWER TRANSDUCER 1 TRANSDUCER 2 SPEED TEMPERATURE 1 TEMPERATURE 2 4 5

+ _ 6 1 2 3 4 5 6 HALO radar pedestal and antenna RI-50 radar interface module Multi-function display set to power control master Other Simrad devices with remote power control Power control bus DC power Activate antenna park HALO 2000 Series and HALO 3000 Series radars have the ability to stop rotating the antenna and hold it at a predetermined angle in relation to the vessels heading line. This park angle is set in the radars software on your multi-function display. In addition, there is a park angle retention feature which is a very low current electromagnetic brake that provides resistance for the antenna to maintain a parked angle against wind and movement when the radar is not powered. The park brake requires a continuous low current DC supply (10-32 V DC). This draws less than 100uA. To activate the antenna brake park function, connect a signal wire from the positive side of the power supply to the Park input on the AUX connector. PAGE | 32 RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD Connect the network cables An Ethernet network is used to distribute the radar data to compatible multi-function displays. The RI-50 is connected to the Ethernet network using the supplied Ethernet cable and Ethernet adapter cable (RJ45 male to 5-pin female, 150 mm (5.9)). RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD PAGE | 33 The RI-50 can be connected directly to any Simrad-compatible multi-function display or to a network switch such as an NEP-2. 1 3 2 4 5 6 1 2 3 4 5 6 HALO radar pedestal and antenna RI-50 radar interface module Compatible multi-function displays NEP-2 or device with a built-in Ethernet switch Ethernet adapter Ethernet cable 1.8 m (6.0) Additional radar functions Additional radar functions such as VelocityTrack and ZoneTrack require good-quality, high-speed GPS position and heading data at 10 Hz or better. The GPS antenna must be mounted in a position that provides a clear view of the sky. A quality 10 Hz compass such as the Precision 9 is suitable for heading, however for the very best performance, a GPS compass such as Simrad HS75 or HS80A should be considered. The connected multi-function display sends NMEA 2000 position and heading data to the radar via the Ethernet connection. For radar chart overlay, an integrated GPS/compass sensor such as the Simrad GS25 is suitable, however the compass is not suitable for VelocityTrack and ZoneTrack as it does not have 10 Hz heading output. PAGE | 34 The following illustration is an example of a GPS and heading NMEA 2000 network:

2 1 3 5 4 6 7 7 _

12 V DC 8 T 9 T 1 2 3 4 5 6 7 8 9 HALO radar pedestal and antenna RI-50 radar interface module Compatible multi-function display NMEA 2000-compliant heading sensor (10 Hz minimum) GPS position sensor Ethernet cable Micro-C drop cables Network power 12 V DC Micro-C backbone (NMEA 2000) with terminators Start the radar When you finish connecting the cables to your RI-50, replace the cover on the circuit board and set the service mode switch on the back of the pedestal to l (power supply enabled). PAGE | 35 RI-50 LED indicator lights LED lights on the front of the RI-50 communicate its operating status. LED Color Indication Likely cause Power Green steady Power is applied and AUX remote power control input is active Normal operation Off No supply voltage or remote power control input is not active Check remote switch position. Ensure 12-24V switch is in correct position for supply voltage Fault Off Blue Purple The fault indicator shows existing conditions as steady colors and historic conditions as blink patterns. Re-power the RI-50 to clear a fault/warning indication. Normal Under or Over voltage Faults are defined as conditions that could cause damage to the equipment. Warnings indicate conditions that can cause the RI-50 to change the operating state of the radar, e.g. switching it to standby. The historic indication helps to identify the cause of intermittent problems. Low supply voltage to the RI-50 Over current including short circuits Input current > 20A or output current > 8A Red Over temperature Red blink Once the RI-50 returns to a stable state, either RUN or OFF, the fault LED will indicate its last condition. Warning .-.-

Warning .-. Warning ..-. Warning . Warning .. The internal temperature > 90C (194F). Caution: The heatsink case may be too hot to touch. Blink patterns indicate the type of fault or warning that is detected. The patterns repeat every 5s. Only one pattern displays at a time. Patterns consist of 1 to 4 blinks with each blink being short

(.) or long (-). Warnings start with short; faults start with long. There are no patterns with all long. Input voltage is unstable. Check the wiring and condition of the battery or power source. The AUX: Remote input was OFF, < 2.5V. Check the Remote Bypass switch or the external connection if used. Flat battery or very low input voltage, < 5V

(12V) or < 9V (24V). Check the input voltage. Low input voltage in 12V system, < 9.5V. The RI-50 switched to standby due to low input voltage. Could be engine cranking or other heavy load. Low input voltage in 24V system, < 19V. The RI-50 switched to standby due to low input voltage. Could be engine cranking or other heavy load. PAGE | 36 Warning ... Warning .... Fault -. Fault -.. Fault -... Fault -.-. Fault -.-

Fault --. Fault -..-

Status Green Normal operation Green/orange fast blinking Wrong or no radar connected Orange Pending shutdown Red Radar is off The RI-50 detected voltage on its output before it turned on. If the radar was only off for a short time, it is normal for there to be residual voltage. However, it can also indicate the output switch in the RI-50 has been damaged and needs repair. This will not stop the radar from working, but does mean the only remaining fault protection in the RI-50 is the 40A input fuse. High input voltage, > 34V. Check your input power source. Input voltages > 36.5V can damage the RI-50. Output voltage too high, > 54V. There is a risk of damage to the connected pedestal. Get the RI-50 checked. Average input current too high, > 20A. The RI-50 will retry up to 5 times before shutting down. Can be caused by low input voltage and/or excessive load from the pedestal. Average output current too high, > 8A. The RI-50 will retry up to 5 times before shutting down. Caused by excessive load from the pedestal. Typically indicates a short circuit on the pedestal cable. The output current was

> 10A. The RI-50 will retry up to 5 times before shutting down. Check the pedestal interconnection cable for damage. Over temperature, > 90C (194F). The RI-50 will re-start after cooling down. The RI-50 should be mounted as shown in the Hardware mounting section of this manual so that air can flow over the heatsink. Low input voltage and heavy pedestal load will increase heating. The wrong pedestal type has been connected. Pedestals designed to work with RI-12 interface modules (older) will not work with RI-50s and could be damaged. A software upgrade is required. Return the RI-50 for service. Output voltage > 45V. The radar will operate regardless of any fault or warning indication. Output voltage 16V to 45V. Check the pedestal is connected and it is a compatible model. Output voltage 16V to 45V. Typically the radar is given 30 seconds to prepare for shutdown. Output voltage <16V. Typically the output is off. PAGE | 37 Ethernet Green blink Successful communication with a multi-function display Normal operation. The LED activity increases with increasing Ethernet traffic. Off Communication not established Ethernet cable disconnected or faulty Ethernet cable to display. Fuse In the rare event that the non-replaceable fuse blows on your RI-50 circuit board, the BLOWN FUSE LED will light up while power is supplied to the RI-50. This indicates an internal fault and you will need to replace your RI-50 unit. Note: A blown fuse indicates an internal fault with your RI-50. It does not indicate a fault with the external wiring to the RI-50 or a fault with the radar pedestal. PAGE | 38 SETUP AND CONFIGURATION Make the following settings before use. Refer to the documentation supplied with your display unit to locate and adjust the settings. Radar source In a system with more than one radar, the device to configure is selected from here. Note: Radars that support dual radar mode are represented twice in the source list, with an A and a B suffix. Radar status Used to view information about your radar, such as the software version, serial number and operating hours. Antenna setup X-axis and Y-axis. Used to set the approximate position of the antenna on the vessel. This enables your vessel icon to be positioned correctly on the PPI. Height. Used to set the height of the antenna above the water line. Ensure the antenna height is set correctly, as it affects the sea clutter function. Do not set the height to zero. Span. Used to select the length of your antenna. Adjust bearing alignment Used to compensate for any slight misalignment of the pedestal during installation and to make sure targets and bearings taken with the electronic bearing line display accurately. The adjustment is made by aligning the heading marker on the screen with the center line of the vessel. Sidelobe suppression Used to increase the suppression if there are false targets appearing as arcs radiating from either side of an actual target (typically large structures such as steel hulled ships, container wharves and large buildings). By default this control is set to Auto, and normally should not need to be adjusted. Note: This setting should only be adjusted by experienced radar users. Target loss in harbor environments can occur if it is not adjusted correctly. Sector blanking Used to stop the radar transmitting in the direction of structures that could cause unwanted reflections or interference to appear on the radar image. Four sectors can be set, the bearing of which is measured from the bow of the vessel to the center line of the sector. Adjust open array park angle Used to set the resting position of the antenna relative to the heading line of the radar when the radar is set to standby. The antenna will stop rotating at the desired offset. Optionally, the antenna can be held in place against wind by connecting the antenna park wire. Note: When entering standby, the antenna may rotate multiple times before coming to rest. HALO light Used to control the brightness level of the blue LED accent light on the pedestal. There are four brightness levels. The level can only be adjusted when the radar is in standby mode. Warning: The pedestals blue accent lighting may not be approved for use in your boating location. Check your local boating regulations before turning the blue accent light on. Reset radar to factory defaults Used to reset the radars control settings (not installation settings) to their factory defaults. PAGE | 39 Error codes If you encounter an error code, power cycle the radar. If the error code reappears, refer to this list for guidance. Error code Description Recommendation 0x00000001 Radar saved settings corrupted Radar will revert to factory defaults. Re-enter your settings including installation settings. 0x0001000C Scanner not detected Check the pedestal interconnection cable connections. Power cycle the radar. Check input voltage. 0x0001000D Transmitter overheat (soft) Try changing to shorter ranges <6 NM. Switch to STBY. Allow unit cool. 0x0001000E Transmitter overheat (hard) Switch to STBY. Isolate power to the radar and contact service. 0x0001000F Signal processing error Unit should revert to STBY. Select transmit. If problem persists, power cycle the radar. 0x00010017 Scanner failure Contact service Power supply 0x00010010 Power supply overheating Switch to STBY. Allow unit to cool then retry. 0x00010011 Power supply voltage error Check pedestal interconnection cable for corrosion or damage. 0x00010012 Power supply overload Contact service 0x00010013 Power supply hardware fault Contact service 0x00010014 Power supply comms fault Contact service 0x00010019 Low battery voltage (Supply voltage low) Recharge and check supply voltage. Restart the radar. 0x00010016 LED Lighting fault Turn accent lighting off then retry. 0x00010018 Radar interface box fault Check LED status light. Check the pedestal interconnection cable for damage. Mechanical 0x00010001 Zero bearing sensor fault Contact service 0x00010002 Bearing sensor fault Contact service 0x00010015 Mechanical transmission Contact service fault 0x00010003 Motor drive fault Contact service 0x0001001A Motor or antenna has stalled Power down the radar. Check and clear antenna obstructions such as ice. PAGE | 40 UPGRADING HALO 3000 Series radars have higher current draw than HALO 3/4/6 Series radars due to a more powerful motor and higher transmit power. If you are upgrading from a HALO 3/4/6 Series radar to a HALO 3000 Series radar, you should change the interconnection cable. If you are upgrading from a HALO 3/4/6 Series radar to a HALO 2000 Series radar, you may use the existing interconnection cable but we recommend you inspect the condition of the connectors. Note: At the time of release, HALO 2000 Series and HALO 3000 Series radars work with Simrad GO XSR, GO XSE (9/12), NSS evo3, NSS evo3S, NSO evo3, NSO evo3S and NSO evo3S MPU systems. They also work with Simrad R2009 and R3016 radar control units. Record the old settings 1 Take note of the old radar settings, i.e. antenna height and span (if re-using the antenna), range offset, bearing alignment, sidelobe suppression, sector blanking and open array park angle. This will help you set up your new radar on the display unit. Isolate power to the radar 2 Turn off the circuit breaker or remove the fuse. Remove the old pedestal 3 Set the service mode switch at the back of the pedestal to 0 (power supply disabled). 4 Disconnect the interconnection cable from the pedestal. 5 Cover the 14-pin end of the interconnection cable to protect it from water and contaminants. 6 Use a socket and torque wrench to remove the dome nuts that hold the antenna to the pedestal. 7 Carefully lift the antenna off the pedestal. PAGE | 41 8 If re-using the antenna, cover the waveguide to protect it from water and contaminants. Remove the RI-12 9 Remove the circuit board cover from the RI-12 by unscrewing the six retaining screws. 10 Remove the grommet retaining clip. 11 Remove the rubber grommets. 12 Disconnect the power cable from the SUPPLY connector. 13 Unplug the RJ45 connector end of the interconnection cable from the SCANNER connector. Note: Keep wires connected to RJ45 connector. 14 Unplug the green 4-way connector from SCANNER POWER connector. Note: Keep wires connected to 4-way connector. 15 If used, unplug the AUX connector. Note: Keep wires connected to the AUX connector. 16 Unplug the Ethernet cable. 17 Unplug the Micro-C NMEA 2000 connector (This cable can be removed as it is not needed with the RI-50 interface module.) 18 Unscrew the RI-12 from its mounted location. 19 Remove the grounding wire if used. PAGE | 42 Install the RI-50 and new pedestal To install the RI-50 and your new HALO 2000 Series or HALO 3000 Series pedestal, follow the steps in the Hardware mounting and Wiring sections in this manual. Note: If you are re-using the original interconnection cable, only connect four wires to the 4-way SCANNER POWER connector on the circuit board. You wont use the 2-way connector. RI-50 Always ON 12/24V 12/24V 20A CASE / SHIP GND POWER CONTROLLED BY AUX REMOTE 24V ONLY SHIELD PAGE | 43 SPECIFICATIONS Type of approval FCC/IC/RED Type Certification HALO 2000 Series FCC ID: RAYHALO2000 (Navico Inc.) IC ID: 978B-HALO2000 (Navico Inc.) HALO 3000 Series FCC ID: RAYHALO3000 (Navico Inc.) IC ID: 978B-HALO3000 (Navico Inc.) EU RED: Emissions compliant to SM1541-4 (including -40 dB/dec future design objectives) and EN302-248 V2.1.1 Environmental Operating temperature

-25C to +55C (-13F to +131F) Relative humidity IEC60945 Exposed product Vibration IEC60945 Exposed product UV IEC60945 Exposed product Waterproofing IPX6 for the pedestal and antenna IPX5 for the RI-50 interface module Relative wind velocity HALO 2000 and HALO 3000 radars with 3 ft, 4 ft or 6 ft antenna have a wind rating of 80 knots at 48 rpm in both 24V and 12V systems. Power Power consumption HALO 2000 Series HALO 3000 Series 235 W (peak, 12V) at maximum wind velocity 380 W (peak, 24V) at maximum wind velocity 45-60 W (average) at zero wind velocity 11 W (average) in standby mode Refers to RI-50 input terminals 250 W (peak, 12V) at maximum wind velocity 395 W (peak, 24V) at maximum wind velocity 45-75 W (average) at zero wind velocity 11 W (average) in standby mode Refers to RI-50 input terminals DC input Radar system input 12 OR 24 V DC into the RI-50 12 V Systems 10.8 - 15 V DC 24 V Systems 20 - 31.2 V DC Pedestal voltage input is 50 V DC nominal generated by RI-50 Power up time 30-40 seconds from POWER OFF to TRANSMIT Physical Height Antenna swing circle diameter Component weights 429 mm (16.88) with antenna mounted 3 ft model: 3.75 ft / 1142 mm / 44.96 4 ft model: 4.73 ft / 1443 mm / 56.81 6 ft model: 6.72 ft / 2047 mm / 80.59 Pedestal Antenna 3 ft Antenna 4 ft Antenna 6 ft RI-50 10 m (33 ft) cable 20 m (66 ft) cable 30 m (100 ft) cable 20.3 Kg (44.8lb) 4.1 Kg (9.0 lb) 4.9 Kg (10.8 lb) 6.5 Kg (14.3 lb) 1.6 Kg (3.5 lb) 1.6 Kg (3.5 lb) 3.2 Kg (7.1 lb) 4.7 Kg (10.4 lb) PAGE | 44 Antenna Rotation speed 16 to 48 rpm depending on operating mode. Beam width Beam width vertical Plane of polarization 3 ft model: 2.4+/-10% (-3 dB width) 1.7 with Beam sharpening mode on 4 ft model: 1.8+/-10% (-3 dB width) 1.3 with Beam sharpening mode on 6 ft model: 1.2+/-10% (-3 dB width) 0.8 with Beam sharpening mode on 25 +/-10 % (-3 dB width) Horizontal polarization Sidelobe level 3 ft Below -23 dB max. (within 10) Below -30 dB max. (outside 10) Side lobe level 4 ft Below -23 dB max. (within 10) Below -30 dB max. (outside 10) Side lobe level 6 ft Below -23 dB max. (within 10) Below -30 dB max. (outside 10) Radar Peak power output HALO 2000 Series 50 W 10% under any transmit condition up to 10% duty cycle max HALO 3000 Series 130 W 10% under any transmit condition up to 13% duty cycle max Transmitter Solid state module with no long-term transmitter power degradation Transmitter frequency Pulse length/PRF and compression ratio Synthesized - Upper half of X-Band 9.390 - 9.495 GHz Pulse length: 0.04 usec Chirp length: 2-64 usec Chirp bandwidth: 2-48 MHz Up to 1 pulse and 4 chirps in a burst with burst repetition rate of 500-

3000Hz. Range and mode dependent. Effective pulse compression ratio less than 150 in all modes. Instrumented range HALO 2000 Series (all antenna sizes) 72 nm HALO 3000 Series (all antenna sizes) 96 nm SART/RACON triggering Yes trigger distance: about 1nm max weather, sea state, and SART position dependent Duplexer Circulator and isolator LNA IF section GaAs front-end Center frequency: 31.25 MHz Bandwidth: 50 MHz max.* A/D; 16 bit 125 MSPS

*Narrower bandwidths defined by signal processing Noise figure 5 dB (Min) at antenna input Compass safe distance Pedestal STD. 1.0 m (3.3 ft) Steer 0.5 m (1.6 ft) RI-50 1.0 m (3.3 ft) PAGE | 45 Other Communication ports Transmit synchronization Ethernet 10/100 Base-T RJ-45 for radar data and control RS-422 output Remote power on Yes Antenna park hold Yes (while radar is unpowered) Motor Brushless with solid state commutation with electromagnetic braking for parking. Interconnecting cable Available in 10 m (33 ft), 20 m (66 ft), 30 m (100 ft) lengths. 20 m (66 ft) length cable included with unit. Options for cable to exit from rear of pedestal or pole mount. 3G/4G or HALO 3/4/6 Series interconnection cables can be used with the HALO 2000 Series only. PAGE | 46 DRAWINGS RI-50 213.0 mm (8.39") 195.0 mm (7.68")

4 7

. 7

m m 5

. 6 9 1

4 6

. 3

m m 5

. 2 9

9 3

. 3

m m 2

. 6 8

6 2

. 3

m m 7

. 2 8 PAGE | 47 Pedestal and antennas 429 mm (16.88") 135 mm (5.31") 294 mm (11.57") 264 mm (10.39")

8 2

. 7

m m 5 8 1 1 4

. 4 4

m m 8 2 1 1 8 3

. 6 5

m m 2 3 4 1 8 2

. 0 8

m m 9 3 0 2

t f 0 7

. 3 t f 0 7

. 4 t f 9 6

. 6 t f t f t f 3 4 6

7 2

. 8

m m 0 1 2

5 3

. 3 1

m m 9 3 3

9 6

. 6

m m 0 7 1

6 7

. 2 1

m m 4 2 3 PAGE | 48 Antenna swing circle diameters m / 44.96"

m / 56.81"

m / 80.59"

3.75 ft / 1142 m 14.73 ft / 1443 m 6.72 ft / 2047 m 3 ft 4 ft 6 ft PAGE | 49 PARTS LIST 000-15762-001 HALO 2000 Series pedestal 000-15766-001 HALO 3000 Series pedestal 000-11464-001 3 ft antenna 3.70 ft / 1128 mm / 44.41 000-11465-001 4 ft antenna 4.70 ft / 1432 mm / 56.38 000-11466-001 6 ft antenna 6.69 ft / 2039 mm / 80.28 000-15757-001 RI-50 radar interface module 000-15767-001 Interconnection cable 10 m (33 ft) 000-15768-001 Interconnection cable 20 m (65.6 ft) 000-15769-001 Interconnection cable 30 m (98.5 ft) 000-11246-001 Adapter cable: yellow Ethernet female to RJ45 male. 150 mm (5.9) PAGE | 50 PAGE | 51

1 0 0

6 4 8 2 1

8 8 9

www.simrad-yachting.comReg. U.S. Pat. & Tm. Off, and common law marks.Visit www.navico.comintellectual-property to review the global trademark rights and accreditations for Navico Holding AS and other entities.

NOTES:

1. USE THE FILE 051-30710-00A.btw FOR PRINTING. 2. BEFORE PRINTING, EDIT THE TEXT MARKED WITH XXXXXXX. 3. PRINT IN BLACK ON SUPPORT P/N 051-3723-00 BY SATO CL4NX PRINTER.

A REV

154295 CR NO

A. Martini APPD TITLE LABEL, SERIAL, HAKU 130W, RADAR

03-NOV-21 DATE CMPD A. Martini DATE 03-NOV-21

Emission. CHANGE DESCRIPTION DOCUMENT NO 051-30710-00 CHKD S. Giachi REV A DATE 09-NOV-21 SHEET 1 OF 1 This document is the property of Navico and contains proprietary and confidential information. This document is loaned solely for the purpose of this quotation or procurement, and on the express condition that the information contained therein shall not be disclosed to others or duplicated or used for any purposes other than this quotation or procurement without the express written consent of Navico. copyright Navico 2007.

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6081687.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case

AN IIA COMPANY

August 22, 2022

Federal Communications Commission

Authorization and Evaluation Division

7434 Oakland Mills Road

Columbia, MD 20145

Subject: Navico Inc’s application for C2PC for their FCC ID: RAYHALO3000

To Whom It May Concern:

We are submitting a request for C2PC for the above referenced FCC Identifier, which was granted on

June 6, 2022.

The original RF Exposure assessment was too conservative and marketing requirements triggered a

more accurate measurement. Therefore, this C2PC comes with the MPE Measurement report, an

updated user manual containing the updated RF Exposure safety distance, revised test reports for Part

80 and 90 with minor clerical updates and an updated tuning procedure which reports the rated output

power.

Should you require any further information, please do not hesitate to let us know.

Regards,

Sharon Hoffman

Agent, Timco Engineering, Inc.

849 NW State Road 45, Newberry, Florida 32669

(352) 472-5500 ● Certification: cb@timcoengr.com ● Testing: testing@timcoengr.com ● www.timcoengr.com

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6081688.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case

AN IIA COMPANY

August 23, 2022

Federal Communications Commission

Authorization and Evaluation Division

7434 Oakland Mills Road

Columbia, MD 20145

Subject: Confidentiality Request Regarding Navico Inc’s FCC ID: RAYHALO3000

To Whom It May Concern:

Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential

treatment of information accompanying this application as outlined below:

Tuning Procedure

The above materials contain trade secrets and proprietary information not customarily released to the

public. The public disclosure of these materials may be harmful to the applicant and provide unjustified

benefits to its competitors.

The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and

all accompanying documentation will not be made before the date of the Grant for this application.

Pursuant to DA04-1705 June 15, 2004, of the Commission’s public notice, we requested temporary

confidential treatment of information accompanying this application as outlined below for 180 days:

User Manual

Test Set up Photos

Regards,

Sharon Hoffman

Agent, Timco Engineering, Inc.

849 NW State Road 45, Newberry, Florida 32669

(352) 472-5500 ● Certification: cb@timcoengr.com ● Testing: testing@timcoengr.com ● www.timcoengr.com

AN IIA COMPANY

849 NW State Road 45, Newberry, Florida 32669

(352) 472-5500 ● Certification: cb@timcoengr.com ● Testing: testing@timcoengr.com ● www.timcoengr.com

NaViIcoO Timco Engineering, Inc. 849 N.W. State Road 45 P.O. Box 370 Newberry, FL 32669 SUBJECT: Application(s) for Certification for FCC ID: R IC: 978B-HALO3000 To Whom It May Concern:

We, the undersigned, hereby authorize Sharon Hoffma apply for certification on our equipment referenced ab ENGINEERING, INC. on our behalf shall have the same We, the applicant, hereby certify that we are not subjec 5301 of the Anti-Drug Act of 1988, 21 U.S.C. 853a, an the application is subject to a denial of federal benefits Navico Inc, 4500 South 129th East Ave, Suite 200 Tulsa, Oklahoma, Postal Code 74134-5885 United States www.navico.com 25/07/2022 AAYHALO3000 nat TIMCO ENGINEERING, INC. on our behalf, to ove. Any and all acts carried out by TIMCO effect as acts of our own. t to a denial of federal benefits pursuant to Section dno "party" (as defined under 47 CFR 1.2002(b) ) to pursuant to that section because of a conviction for possession or distribution of a controlled substance. This authorization expires December 31, 2022. Regards, A * am Gm Filippo Campolmi Regulatory Compliance Engineering Manager

AN IIA COMPANY May 3, 2022 Timco Engineering, Inc 849 NW State Road 45 Newberry, FL 32669 Re: Grant Deferral Request for FCC ID: RAYHALO3000, IC: 978B-HAL03000 To Whom It May Concern:

Navico Inc. has requested the grant deferral date to be changed to June 6, 2022 for the above referenced FCC ID and IC Certification number. If you have any questions or require any further information, please let me know. Regards, Sharon Hoffman Agent 849 NW State Road 45, Newberry, Florida 32669

(352) 472-5500 Certification: cb@timcoengr.com Testing: testing@timcoengr.com www.timcoengr.com

AN IIA COMPANY March 18, 2022 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA Re: Navico Inc.s FCC ID: RAYHALO3000 Gentlemen, This equipment meets the requirements of the FCC Rules, Part 90.203(e) and (g), as applicable. Programming of this products transmit frequencies can be performed ONLY by the manufacturer or by service or maintenance personnel. The operator cannot program transmit frequencies using the equipments external operation controls. Sincerely, Sharon Hoffman Agent 849 NW State Road 45, Newberry, Florida 32669

(352) 472-5500 Certification: cb@timcoengr.com Testing: testing@timcoengr.com www.timcoengr.com