User Manual Table Contents Table of Contents Important safety instructions ...................................................01 1. Know your air purier ..........................................................03 2. Get started 3. Use an air purier 2.1 Install the lter ..............................................................04 3.1 Know the control panel...................................................06 3.2 Know the lter replacement indicator ..............................06 3.3 Regulating fan speed .....................................................06 3.4 Ion mode .......................................................................06 3.5 Timer button ..................................................................07 3.6 Auto ..............................................................................07 3.7 Sleep mode ...................................................................07 3.8 Clean an air purier.........................................................07 4. Replace the lter .................................................................08 5. Clean the pre-lter...............................................................10 6. Know LED display on the viewing window..............................10 7. Failure modes and treatment methods...................................11 8. Specications ....................................................................12 9. Packing list ........................................................................13 10. Warranty card ...................................................................14 01 02 1.Know your air purier Thank you for choosing the air purier produced by our company. Before using, please read this manual in detail to correctly grasp the use of this air purier in order to give full play to the best performance of the purier. 1. Air outlet cover 2. Control panel 3. Viewing window 4. Main unit 5. Decorative board 6. Base 03 Get started 2.Get started Install the lter:
A high-eciency composite lter is included inside the air purier. Before using the product, the packing of the lter must be removed. Remove lter assembly and its packing as follows, then put it back in the air purier. Holding tabs Main unit Filter Pre-Filter Back cover Note:
Install the lter in the correct position. Make sure that the side with holding tabs is facing outward. 04 1.Hold the machine and the top left and right sides of the back cover with both hands, and press the back cover with your thumb.(When you hear a clicking sound) The back cover pops open. 2. Grab the back cover and remove the main unit. Then pull the packaged lter outward to remove it from the machine and remove the plastic bag from the lter. 3. Put the lter back into the rear of the purier, then t the three at columns at the bottom of the back cover to the three holes at the bottom of the rear of the purier. Hold the top left and right corners of the back cover with both hands and push the back cover into the rear of the purier. (When you hear clicking sound) The back cover is locked. 05 4. Use an air purier 4.1 Know the control panel:
3.Use an air purier 3.1Know the control panel:
Timer button Filter replacement tips Temperture display Humidity display Regulating fan speed AUTO F
%rh AUTO UV WIFI UV lamp Sleep Switch Timing remaining
(or PM2.5 unit quantity) 3.2 Know the lter replacement indicator:
An eective composite lter assembly is included inside the product. When the indicator light is on, it indicates the lter needs to be cleaned or replaced. 3.3 Regulating fan speed You can select the desired fan speed and the system starts at the high speed by default. 1. Press the switch button to turn on the purier. 2. Press the fan speed button repeatedly to switch the desired fan speed. 3.4 UV mode Press the button to activate the ion mode, in which 95% of the bacteria in the air can be killed through the air purier. UV 06 Use an air purier 3.5 Timer button 1. Touch the timer button once to enter the query for the remaining time. 888 displays the remaining time. If there is no operation within 5 seconds, and it will automatically return to display PM2.5. 2. In the state of query, touch the timer button once again , ashes, and then 888 and the clock light on the left of it are on. 3. Enter the timing state. Touch the timer button once, the timing mode of 1H-2H- 4H-8H-... is displayed on the LED screen. 4. When timing adjustment is done, if there is no operation after 5 seconds, 888 will automatically switch back to the state of displaying PM2.5, which indicates that the setting is okay. 5. Press and hold for 3 seconds to cancel the timing function. 3.6 AUTO In any state, press the auto button once to trigger the auto mode, and the PM2.5 sensor head starts to sense the PM2.5 value of the current environment, and adjust the gear position of the motor corresponding to the value of PM2.5. 3.7 Sleep mode In any state, press the sleep button to enter the sleep mode, run in the sleep mode. Except the sleep mode is displayed on the LED, all the back lights should be turned o immediately; the negative ions/plasma are turned o. In sleep mode, touch the sleep button again to cancel the sleep mode. 3.8 Clean an air purier Clean the inside and outside of the air purier regularly to prevent dust accumulation. 1. Wipe the dust o this air purier with a soft, dry cloth. 2. Clean the air inlet and outlet with a soft, dry cloth. Note:
Always unplug the power cord before cleaning the air purier. Do not immerse the air purier in water or any other liquids. Never use abrasive, corrosive or ammable detergents (such as bleach or alcohol) to clean any part of the air purier. The lters of this machine cannot be washed in water or cleaned with other cleaners, and the lters should be replaced directly. 07 4.Filter relacement When the lter replacement indicator is ashing, it reminds you that you need to check to replace the lter. Note:
High-ecient composite lters can not be washed in water or cleaned by vacuum cleaners. Make sure the side with the holding tabs is facing outwards. 1. Turn o the purier and unplug the power cord. As shown in Figure (a). 2. Hold the machine and the top left and right sides of the back cover with both hands, and press the back cover with your thumb. (When you hear a clicking sound) The back cover pops open, as shown in Figure
(b). 3. Grab the back cover and remove the main unit. Then pull the packaged lter outward to remove it from the machine As shown in Figure . 4. Remove the plastic bag from the lter. As shown in Figure (d). 08 5. Put the lter back into the air purier. See Figure (e) Note:
6. Put the lter back into the rear of the purier, then t the three at columns at the bottom of the back cover to the three holes at the bottom of the rear of the purier. Hold the top left and right corners of the back cover with both hands and push the back cover into the rear of the purier. (When you hear clicking sound) The back cover is locked. As shown in Figure (f). 09 5.Clean the pre-lter A vacuum cleaner can be used to regularly clean dirt on the pre-lter, or it can be washed and dried for further use. 6.Know LED display on the viewing window There is an LED backlight on the viewing window (three colors of red, blue and green respectively), and the color of the light is automatically displayed according to the number of PM2.5: (0-49 green light, 50-99 blue light, more than 100 red light) At the same time, green light indicates excellent air quality, blue light indicates good air quality, and red light indicates poor air quality. 10 Troubleshooting 7.Failure modes and treatment methods This chapter summarizes the problems you most often encounter when using an air purier. If you are unable to solve the problem based on the information below, please contact the Customer Service Center in your country. 11 8.Specicaions 12 10 11 9.Packing list 13 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the users authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement:
The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.