NLM18S / NLM19S NLM18S / NLM19S Color TFT-LCD Monitor Users Manual NLM18S / NLM19S Color TFT- LCD Monitor OPERATION MANUAL CONTENTS NOTES ON LCD MONITORS
..3 STATUS INFORMATION 12 SAFETY PRECAUTIONS 4,5 OSD USAGE
...13,14 SUPPLIED ACCESSORIES 6 BEFORE CALLING FOR REPAIR SERVICE PREPARATION 15 Cable Connection 7 SPECIFICATIONS LOCATION OF USERS CONTROL 8 NLM18S / NLM19S 16 MONITOR INSTALLATION
.9,10,11 Available PC VGA Mode INTERNATIONAL STANDARDS 17 18 NLM18S / NLM19S Color TFT- LCD Monitor Notes On LCD Monitors 1.The LCD panel used in this monitor is a very high technology product with 3,932,160 thin film transistors, giving you fine picture details. Occasionally, a few non-active pixels may appear on the screen as a fixed point of red, green, blue, white or black. Please note that this does not indicate a defective panel. 2. Set your resolution to 1280 x 1024 pixels at 60Hz refresh rate for optimum display quality. The display may become a bit blurry when you set the resolution to other than 1280 x1024. Please note that this does not indicate a defective product. 3. The screen surface is very soft. Do not rub, touch or tap the screen surface with sharp object such as pen or pencil. This contact may scratch or damage the screen. These damages are not covered under the warranty. 4. Turn your computer OFF before installing your new monitor. SAFETY PRECAUTIONS Improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your color TFT-LCD monitor product, please read the following precautions carefully before using the product.
All operating instructions must be read and understood before the product is operated.
These safety and operating instructions must be kept in safe place for future reference.
All warnings on the product and in the instructions must be observed closely.
All operating instructions must be followed.
Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents.
This product must be operated on a power source specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company. For units designed to operate on batteries or another power source, refer to the operating instructions.
The power cords must be routed properly to prevent people from stepping on them or objects from resting on them. Check the cords at the plugs and product.
Do not overload AC outlets or extension cords. Overloading can cause fire or electric shock.
Never insert an object into the product through vents or openings. High voltage flows in the product, and inserting an object can cause electric shock and/or short internal parts. For the same reason, do not spill water or liquid on the product.
Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other dangerous conditions. Request a qualified service person to perform servicing.
If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualified service person to perform repairs. a. When the power cord or plug in damaged. b. When a liquid was spilled on the product or when objects have fallen into the product. c. When the product has been exposed to rain or water. d. When the product does not operate properly as described in the operating instructions. Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not described in the instructions can cause damage, which often requires extensive adjustment work by a qualified technician. e. When the product has been dropped or damaged. f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product needs servicing.
In case the product needs replacement parts, make sure that the service person uses replacement parts specified by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.
Upon completion of service or repair work, request the service technician to perform safety checks to ensure that the product is in proper operating condition.
When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer. 4 SAFETY PRECAUTIONS (Continued)
Unplug the power cord from the AC outlet before cleaning the product. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol cleaners.
Unplug the power cord from the AC outlet if you do not use the product for considerably long time.
Do not use the product near water, such as bathtub, washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement.
Keep the product away from direct rays of the Sun-light.
Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer's instruction. Use only the mounting hardware recommended by the manufacturer.
When relocating the product placed on a cart, it must be moved with the utmost care. Sudden stops, excessive force and uneven floor surface can cause the product to fall from the cart.
The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer's instructions are followed.
The LCD panel used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
Keep the product away from heat sources such as radiators, heaters, stoves and other heat-
generating products (including amplifiers). 5 SUPPLIED ACCESSORIES Make sure the following accessories are provided with the product. NLM18S / NLM19S NLM18S / NLM19S Color TFT-LCD Monitor Users Manual Users Manual (*1) Monitor Driver Diskette (x1) PC VGA Cable(*1) AC Cord (*1) 6 PREPARATION Cable Connection Cable Connector Description 1 2 1 Power Input : AC 100~240Vac 2 Analog RGB : PC VGA Cable VGA & Power Cable Connection 2 1 7 LOCATION OF CONTROL PANEL Control Panel on the front of main unit 1 2 3 4 5 1 MENU : Display menu window / Exit from sub menu Exit from OSD window 2 UP : Adjust setting value (Increase) / Move up 3 DOWN : Adjust setting value (Decrease) / Move down 4 SEL : Select menu item on OSD window Hot key for auto adjustment Rear Front 6 5 POWER : On / Off 6 POWER LED :
On Power On Sleep Mode Power Off LED Status Green LED Orange LED LED 8 Remak No signal (PC Mode)
MONITOR INSTALLATION The instruction below is for Windows 2000 1 Double click [Control Panel ] icon from [My Computer] folder. 2 Double click [Display] icon from
[Control Panel] folder. 3 Select [Settings] in [Display Properties]
window and then click [Advanced...]. 4 Select [Monitor] in the window shown above and then click [Properties]. 9 MONITOR INSTALLATION(Continued) 5 Select [Driver] and then click [Update Driver...]. 6 Click [Next>]. 7 Select the second list and then click
[Next>]. 8 Click [Have Disk...]. 10 MONITOR INSTALLATION(Continued) 9 Click [Browse] to select CD-ROM drive. 10 Choose Your Monitor Model, then click
[Next>] to proceed to the next step. 11 Click [Next>] to start installation. 12 Click [Yes] to proceed to the next step. 13 Click [Finish].
(Be sure the screen shows correct model name.) 11 STATUS INFORMATION Resolution Vertical Frequency 1280 X 1024 75Hz Auto Config Selected Menu Icon Name Auto Config Brightness Contrast H V Position Position Clock Phase Language Red Green Blue OSD H Position OSD V Position Reset 12 OSD USAGE Menu Auto Config Brightness Contrast Operation Operate the auto adjustment DOWN : Decrease Brightness UP : Increase Brightness
Contrast is ratio of luminance between black and white.
When contrast is reduced (DOWN button), the luminance of white is reduced and the display becomes darker.
When contrast is increased(UP button), the luminance of white is increased and the display becomes clear. DOWN Button : Decrease Contrast UP Button : Increase Contrast W B H Position DOWN Button:
Move Left deo UP Button :
Move Right BW Vid V Position DOWN Button Move Down Video UP Button :
Move Up Video
Adjust horizontal size by using Down or UP buttons.
Caution Do not make manual adjustment when the picture is in its Normal shaped or you will create problem on it.
When noise remains on the screen after operating the auto adjustment, adjust it by using Down or UP buttons.
Caution Clock Phase Perform this adjustment just in the case of having horizontally unmatched picture after operating the auto adjustment Language
Select the language of OSD menu
- English / Franais / Italiano / Deutschland / Korean Red
Adjust Red Color by using DOWN or UP buttons. Green
Adjust Green Color by using DOWN or UP buttons. Blue
Adjust Blue Color by using DOWN or UP buttons. 13 OSD USAGE (continued) Menu OSD H Position OSD V Position Operation
Adjust OSD H Position by using DOWN or UP buttons.
Adjust OSD V Positon by using DOWN or UP buttons. Reset
Reset values to initial value at time of forwarding at the factory. 14 BEFORE CALLING FOR REPAIR SERVICE Before calling for repair service, check the following items for possible remedies to the encountered symptoms. Check below Reference Pages Problem There is no picture Make sure the power cord is properly inserted in the power outlet. Make sure the main power button of the main unit is on. Make sure the signal cable is free of connections. Make sure whether the power of an external input device is on. Fluorescent lamp may have reached the end of service life. 7 8 7
16 8 13 Picture is not clear Operate the auto adjustment Adjust the Frequency and the Phase. 15 SPECIFICATIONS Color TFT LCD Monitor Resolution Color Brightness Contrast Ratio Viewing Angle 1280 * 1024, SXGA 16,777,216 Colors (Full Color) 250 cd/m2(nit) NLM18S : 400 : 1 NLM19S : 500 : 1 NLM18S : 160 (H) / 160 (V) NLM19S : 170 (H) / 170 (V) Type Amorphous Si TFT-LCD Panel Actual Display Size PC Signal
(Analog RGB) Diagonal Length H-Frequency V-Frequency Signal Level Power Voltage Input Power Consumption On NLM18N : 357.12(H) x 285.696(V) mm NLM19N : 376.32(H) x 301.056(V) mm NLM18S : 18.0", 457.34 mm NLM19S : 19.0, 481.92 mm 30~80 KHz 56~75 Hz 0.7Vp-p AC100~240V, 50/60Hz NLM18S : Max. 45 Watt NLM19S : Max. 45 Watt Size Weight Off- Mode Max. 3 Watt W*H*D mm 485 x 383 x 57 mm , 174 mm (Stand Depth) NLM18S : 7.0 Kg (w/o accessories) NLM19S : 7.2 Kg (w/o accessories) 16 SPECIFICATIONS Available PC VGA Mode Resolution 640 x 350 720 x 400 640 x 480 800 x 600 832 x 624 1024 x 768 1280 x 1024 Vertical Horizontal Frequency
(Hz) Polarity Frequency
(KHz) Polarity Pixel Rate Standard
(MHz) Type Remark 70.09 70.09 59.94 66.67 72.81 75.00 56.25 60.32 72.19 75.00 74.55 60.00 60.00 70.07 72.10 74.93 75.03 60.02 75.03 N P N N N N N/P P P P N N N N P N P P P 31.47 31.47 31.47 35.00 37.86 37.50 35.16 37.88 48.08 46.88 49.73 48.36 48.78 56.48 57.52 60.24 60.02 63.98 79.98 17 N N N N N N 25.175 28.322 25.175 30.240 31.500 31.500 N/P 36.000 40.000 DOS VGA IBM IBM VESA MAC VESA VESA VESA VESA P P P N N N N P N P P P 50.000 VESA SVGA 49.500 VESA 57.283 MAC 65.000 VESA 64.000 MAC 75.000 VESA 75.000 80.000 78.750 108.000 135.000 IBM MAC VESA VESA VESA XGA SXGA INTERNATIONAL STANDARDS FCC CAUTION : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. CE EN55022 "Limits and methods of measurement of radio disturbance characteristics of information technology equipment (ITE)"
EN55024 "Information technology equipment - Immunity characteristics - Limits and methods of measurement"
EN61000-3-2 "Limits for harmonic current emissions (equipment input current <= 16A per phase)"
EN61000-3-3 "Limitation of voltage fluctuations and flicker in low-voltage supply system for equipment with rated current <= 16A EN60950 Safety for information technology equipment including electrical buisness equipment 18