INDOOR HOTSPOT QUICK START GUIDE Indoor Hotspot Quick Start Guide Box Contents Your Nebra Indoor Helium Hotspot comes with the following items:
The Nebra Helium Indoor Hotspot RP-SMA LoRa Antenna Worldwide 12V 1.5A Power Adapter 1M CAT5 Ethernet Cable Warnings Please remember to follow the following steps when using your Nebra Indoor Hotspot. Never power on the Indoor hotspot without its antenna connected as this Do not place in direct sunlight or on hot surfaces (e.g a Heater). The Indoor units case is designed to be used indoors, and is not suitable may damage the unit. for use outside. Preparing Your Nebra Indoor Hotspot Step 1: First screw in the included antenna into the connector on the back of the hotspot. Step 2: Next nd a suitable location for your Hotspot to be positioned, to provide the best coverage we recommend placing it near a window just out of direct sunlight. Youll need to be near a mains power source too. Step 3: If you are using a wired Ethernet connection, connect an Ethernet cable between a router or switch and the Ethernet jack on the Hotspot. Step 4: Fit the appropriate power plug for your country onto the universal power supply and plug it into a mains outlet. Step 5: Finally connect the DC Jack from the power supply into the power receptacle on the Hotspot. You should then see the lower LED on the back of the unit turn on, the hotspot will now take up to 5 minutes to congure for its rst boot. The upper light will turn on when it is ready to continue for conguration. If you have connected it to a wired Ethernet connection this process may take slightly longer as itll also perform rmware updates as soon as it gets a connection to the internet. 1 Nebra LTD. 2021 INDOOR HOTSPOT QUICK START GUIDE Conguring Your Nebra Indoor Hotspot To congure your Hotspot you will require the Helium Network application installed on a Mobile Phone and for you to have gone through the account setup process to continue. Step 1: Open the Helium application and login, then press hotspots. Step 2: Next click Set up Hotspot , from here you will want to select Nebra Indoor Hotspot. Step 3: After following the steps on the App to get to this page, Push the button on the back of the unit once to enable pairing and then press scan on the App. Step 5: Press the entry for your hotspot in the app, you can check it is the correct one by matching the last 6 characters shown in the application with the last 6 characters of the mac address printed on the sticker on the bottom of the hotspot. Step 6: The app will show the available Wi-Fi networks within range of your Hotspot. If you are using Ethernet, tap Use Ethernet Instead and skip to Step 7. If using Wi-Fi, tap on the name of your Wi-Fi network on the app which will bring you to the following screen. Type in your Wi-Fis network password then tap Connect and it should connect to your wi- network. Step 7: The app will then ask for you to set your hotspots location. Step 8: Finally you can conrm the location of your hotspot. Click continue and you should be presented with a map to then place where your hotspot is on the app. Step 9: The setup should now be complete, itll submit the details of the Hotspot to the Helium network and then in approximately 15 minutes conrm its added to the network. 2 Nebra LTD. 2021 INDOOR HOTSPOT QUICK START GUIDE Figure 1: Choose your Hotspot 3 Nebra LTD. 2021 INDOOR HOTSPOT QUICK START GUIDE Figure 2: Bluetooth Information 4 Nebra LTD. 2021 INDOOR HOTSPOT QUICK START GUIDE Figure 3: Hotspot Found 5 Nebra LTD. 2021 INDOOR HOTSPOT QUICK START GUIDE Figure 4: Congure Network Connection 6 Nebra LTD. 2021 INDOOR HOTSPOT QUICK START GUIDE Figure 5: Wi-Fi Password 7 Nebra LTD. 2021 INDOOR HOTSPOT QUICK START GUIDE Figure 6: Setting Hotspot Location 8 Nebra LTD. 2021 INDOOR HOTSPOT QUICK START GUIDE Figure 7: Pre-paid Fees 9 Nebra LTD. 2021 INDOOR HOTSPOT QUICK START GUIDE Figure 8: Registering Hotspot 10 Nebra LTD. 2021 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Statement the equipment. NOTE: