APPLICATION NEXT ASSY PROJECT NO. ECN NO.
---
REVISIONS DESCRIPTION REV 1.13 SPECIFICATION RELEASE 1.14 UPDATE SPECIFICATION 1.15 UPDATE SPECIFICATION 1.16 UPDATE SPECIFICATION 1.17 UPDATE SPECIFICATION DATE 5/6/2015 6/30/2015 7/20/2015 8/19/2015 9/4/2015 APPROVALS APPROVED HP RESTRICTED THIS DOCUMENT AND ANY ASSOCIATED DATA CONTAIN RESTRICTED INFORMATION THAT IS
(HP) PROPERTY. DO NOT DISCLOSE TO OR DUPLICATE FOR OTHERS EXCEPT AS AUTHORIZED BY HP. HEWLETT-PACKARD UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES
[MILLIMETERS]. TOLERANCES ARE:
FRACTIONS 1/32 DECIMALS
.XX .02
[0.5]
.XXX .010 [0.25]
ANGLES 1 APPROVALS DATE DRAWN CHECKED DSGN ENGR NAM NGUYEN 2/12/15 ENG MFG PROCUREME NT QA LEGAL AGENCY 2015 COMMERCIAL WIRELESS CHARGER BOLT DRAWING NO. SIZE A REV 1.17 DO NOT SCALE DRAWING SUPPLEMENTS:
EF,PDF SHEET 1 OF 15 TABLE OF CONTENTS 1. 2. 3. 4. 5. 6. SCOPE....................................................................................................................................................................................6 ORDER OF PRECEDENCE................................................................................................................................................6 DESIGN FOR ENVIRONMENTAL REQUIREMENTS (GENERAL PRODUCT REQUIREMENTS)...................6 GENERAL EXPECTATIONS.............................................................................................................................................8 HP PART NUMBER.............................................................................................................................................................8 WIRELESS CHARGE DESIGN REQUIREMENTS....................................................................................................... 9 6.1 WIRELESS DESIGN........................................................................................................................................................................9 QUALITY ASSURANCE PROVISIONS......................................................................................................................................12 CHANGE NOTICE.............................................................................................................................................................13 PACKAGING/SHIPPING..................................................................................................................................................13 7. 8. 9. APPENDIX A 13 REVISION HISTORY Revision Date 1.10 1.11 1.12 2/13/15 4/9/15 4/16/15 Author Nam Nguyen Nam Nguyen Nam Nguyen Description Official release Dimension change 167.2mm x 90.2mm Add support for AiO Stand base. Add different support for DC plug for Standalone and AiO stand base. 1.13 5/5/2015 Nam Nguyen 1.14 6/22/2015 Nam Nguyen 1.15 7/20/2015 Nam Nguyen 1.16 8/19/2015 Nam Nguyen 1.17 9/4/2015 Nam Nguyen Add new part number for power adaptor with 1.5M cable Update GP file Update material, color for top and bottom cover. Delete Switch Delete Audible Change LED from Bi-Color to Single Color Update LED behavior table Update GP file (BOLT_GB_DB_15-0618) Update color and material Add update FW function via Micro USB LED brightness luminance = 100 nits Ambient operation temp: 35 deg C and 10 degree C delta temperature for module (45 degree C Max) ESD 8KV contact and 15 KV Air Update LED table behavior Update Pulsing and Flashing duty cycle. Update Tick mark on the Bolt design Update ID GP file Update Top and Bottom cover material and color 1. SCOPE This specification defines the requirements for a tri-mode (Qi, PMA, A4WP class 2) wireless charging module for charging a single phone or phablet of up to 6 inch diagonal screen length. The OEM need to provide the complete wireless charging solution and required certifications. This module will be standalone module or integrated to AiO stand base. The standalone module will have cover around the electronic, coil, and shielding. For AiO stand base, only the electronic, coil, and shield. 2. ORDER OF PRECEDENCE In the event of a conflict between this specification and references cited herein, the order of precedence shall be this specification, then any reference documents, and finally any appendices. 3. DESIGN FOR ENVIRONMENTAL REQUIREMENTS (GENERAL PRODUCT REQUIREMENTS) This section defines requirements that are applicable to all products and product components. Individual components specifications may amend or append requirements to this base set as part of their component-specific requirements, but otherwise these requirements are applicable in all cases. Specifications referenced within this section form a part of this specification to the extent specified herein. Unless otherwise indicated, the document is of the issue in effect on the date of invitation to bid or request for proposal. 3.1.1 Environmental Design Requirements 3.1.1.1 The following embedded document contains environmental requirements that the product must incorporate into its design to meet both regulated and HP-voluntary initiatives. Any deviation from these requirements will cause this product to not be in compliance with the standards that HP enforces to maintain its responsibility to the environment. Environmental System Specification for 2016 CMIT Acessories - 012914.docx 3.1.2 Accessibility 3.1.2.1 SECTION 508 ACCESSIBILITY - US The system must comply with the section 508 Accessibility - US requirements. Please reference:
http://www.section508.gov/index.cfm?FuseAction=content&ID=12 3.1.2.2 CVAA The system (modules) must comply with the Twenty-First Century Communications and Video Accessibility Act (CVAA) via completion of the HP CVAA worksheet available from the Accessibility & Aging Program Office at ability@hp.com for each module that includes accessibility considerations.
(ie. keyboards, VOIP software, electronic messaging, video conferencing (ACS)) 4. GENERAL EXPECTATIONS a) All documents shall be provided in electronic form in industry standard formats such as Adobe Acrobat PDF, Microsoft Excel, etc. unless otherwise indicated. Adobe Acrobat documents should be searchable and generated from an electronic documentnot from a document which was scanned. b) Any performance related discussions shall be between HP/wireless charge suppliers only. c) Measurement/simulation data shall be provided to HP only. d) Mechanical related information (e.g. 3D drawing, cable/connector definition/type, etc) shall be provided by ODM. e) ODM suppliers SOP documentations shall be available upon request. f) g) Additional expectations are described in the HPPA documents. Schedule/sample quantity shall be provided by ODM. 5. HP PART NUMBER HPs 6-3 part number for webcam = TBD. 6. WIRELESS CHARGE DESIGN REQUIREMENTS HP reserves the right to modify the design requirements with advance notice. 6.1 WIRELESS DESIGN Technology:
Power:
X-Y Dimension:
Thickness:
Cable routing for standalone:
Cable routing for AiO stand:
Firmware update:
LED Status:
Input Power:
Header for LED:
DC Plug Operation temperature:
ESD:
Tri Mode (Qi, PMA, and A4WP Class 2) Qi & PMA 5W delivered to receiving device;
A4WP Class 2 10W delivered to receiving device. 167.2mm x 90.2mm (of charging surface and electronic) As thin as possible. Cable recess plug under the body of the module Cable will plug to the DC plug at the side of the AiO stand base. To maintain the up to date interoperability of the wireless device Unit need to be able to update FW via Micro USB port. Need to provide LED to show status. Bi-Color (White and Amber) 12V 2 or 3 pin header for single color (White) DC Plug down for (Standalone Module) DC plug with extension cable to the edge of the AiO base. 35 degree C ambient and 10 degree C delta temperature for the module means 45 degree C max. 8 kV contact and 15 kV Air. Certification:
Location of Certification Logo:
Icon/Logo:
ODM need to obtain all applicable regulatory certifications for A4WP and PAM standards body certifications TBD Top icon location for centering the device (Final icon TBD) 6.1.1 Power Adaptor See spec 794797-A
-WAE009-022G2 => 1.5 mm DC cable 6.1.2 LED Behavior (preliminary) LED luminance:
Flashing:
Pulsing:
100 nits. 50% duty cycle 10% duty cycle at 1Hz LED Status Unplugged/Off On/Ready (=Charge complete) Charging Error condition FW Update in process LED Off Solid White Solid Amber Flash Amber Pulsing White 6.1.3 Mechanical Top Cover:
o Material = Plastic PC/ABS + 15% talc o Plastic Color = Jack Black o Finish = MT11000 o Surface = Paint o Paint Base Coat = Sparkling Black UV o Paint Top Coat = Soft touch clear UV Bottom o Rubber feet Process = Die cast aluminum Material = Aluminum Finish = Smooth Surface = Paint Paint Primer = TBD Paint Base Coat = HP Blue (PM285c) PU Paint Top Coat = PU Soft touch Clear 6.1.4 GP (Graphic Plan) File BOLT_GP_SI_15-0827 7. QUALITY ASSURANCE PROVISIONS Unless otherwise specified in the contract or purchase order, the supplier shall be responsible for the quality of the part as it is delivered to HP. The supplier shall be responsible for having controlled processes to ensure product is in total compliance with this specification. Failing lots shall be subject to return or other supplier-corrective action. In addition to visual inspections, the following minimal tests shall be performed on every finished goods (100%) before shipping to HP/ODM sites/factories. 8. CHANGE NOTICE During development or after tooling release, any design or process changes initiated by ODM supplier shall be communicated to HP through email and approved by HP prior to implementation. The supplier must provide adequate samples and reports to allow HP to verify the change. 9. PACKAGING/SHIPPING Packaging shall sufficient to protect against damage or loss during shipment from the supplier to destination specified in the purchase order. Packaging, identification, and palletization shall be in accordance with HP Document 109893 (Appendix A). It shall be clearly marked with Supplier part number, HP part number, and a Revision number. HP SUPPLIER PACKAGING/MATERIAL HANDLING SPECIFICATION APPENDIX A 109893_AC_001.pdf NOTE: The USB port is just only for engineering purposes in the factory and cannot not be used by the end-user. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help
- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. interference to radio communications. However,