FCC ID: 2AEJD-103902-1-DT50 Robust and highly integrated 3x3 WLAN (802.11a/n) communication module

DT50RF

(5127) Integration Manual Company Confidential Version:

1.3 Author:

Doc.-No.:

5127.30.316 Status:

Approved Approved by:

Date:

2020-05-06 Owner:

File Name DT50RF_Integrator_Manual.docx Michael Aeschbacher Michael Aeschbacher Markus Honegger DT50RF (5127) Integration Manual Michael Aeschbacher Version History Version Date Author Status Comments 2015-11-25 Schwand Draft Initial document 2015-11-30 Schwand Draft Added FCC ID 2016-03-24 Aescmic Approved 2016-06-07 Aescmic Approved IC ID corrected 2020-04-14 Aescmic Approved IDs updated 2020-05-06 Aescmic Approved Updated according to KDB 996369 0.1 0.2 1.0 1.1 1.2 1.3 The reproduction, distribution and utilization of this document as well as the communication of its contents to others without express authorization is prohibited. Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a patent, utility model or design. Weitergabe sowie Vervielfltigung dieses Dokuments, Verwertung und Mitteilung seines Inhalts sind verboten, soweit nicht ausdrcklich gestattet. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte fr den Fall der Patent-, Gebrauchsmuster- oder Geschmacksmustereintragung vorbehalten. Doc.-Name: DT50RF_Integrator_Manual.docx, V1.3, Doc.-No.: 5127.30.316 Document date: 2020-05-06 printed versions are uncontrolled copies!

Neratec Solutions AG, CH-8608 Bubikon, Company Confidential Page 2 (7) DT50RF (5127) Integration Manual Michael Aeschbacher Table of Contents 1 Labeling ........................................................................................................................................................... 4 1.1 The electronic label is accessible .............................................................................................................. 4 2 Module installation instructions ................................................................................................................... 5 2.1 General note .............................................................................................................................................. 5 2.2 Installation ................................................................................................................................................. 5 3 Regulatory Compliance ................................................................................................................................. 6 3.1 Applicable rules ......................................................................................................................................... 6 3.2 FCC Part 15, Class B ................................................................................................................................ 6 3.3 Industry Canada ........................................................................................................................................ 6 3.4 RF Exposure .............................................................................................................................................. 6 3.5 Professional Installation ............................................................................................................................ 7 3.6 Antennas ................................................................................................................................................... 7 3.7 Module Co-location .................................................................................................................................... 7 3.8 Host product testing ................................................................................................................................... 7 Doc.-Name: DT50RF_Integrator_Manual.docx, V1.3, Doc.-No.: 5127.30.316 Document date: 2020-05-06 printed versions are uncontrolled copies!

Neratec Solutions AG, CH-8608 Bubikon, Company Confidential Page 3 (7) The end product has an electronic label including the following text:

FCC ID 2AEJD-103902-1-DT50 DT50RF (5127) Integration Manual Michael Aeschbacher 1 Labeling IC 9301A-1039021DT50 Model DT50RF_MK2_1 Region Domain Settings Grantee information Technical Contact 1.1 The electronic label is accessible Devices based on factory configuration do show the e-label using a state of the art web browser:

http://192.168.1.20 https://192.168.1.20 The e-label is showed on the start page of the web GUI. Doc.-Name: DT50RF_Integrator_Manual.docx, V1.3, Doc.-No.: 5127.30.316 Document date: 2020-05-06 printed versions are uncontrolled copies!

Neratec Solutions AG, CH-8608 Bubikon, Company Confidential Page 4 (7) 2 Module installation instructions DT50RF (5127) Integration Manual Michael Aeschbacher 2.1 General note 2.2 Installation The module cannot be tested without a baseboard. Therefore, we have a limited modular approval. The module shall be used always in combination with a Neratec DT50 baseboard. DT50RF_MK2_1 module has the dimensions according to Figure 1. Module thickness is 5 mm and with RF connectors 7 mm. The DT50RF_MK2_1 need to be fixed to the end product with four M2.5 screws. Figure 1 Dimensions of DT50RF_MK2 module The module is connected by a PCIe interface and three MMCX antenna connectors. Following operation conditions need to be complied when the module is implemented into an end product. Parameter Value Operation temperature

-40 +85C 3.3V supply voltage 2.97 3.63V Current consumption 2500mA peak; 2000mA average Doc.-Name: DT50RF_Integrator_Manual.docx, V1.3, Doc.-No.: 5127.30.316 Document date: 2020-05-06 printed versions are uncontrolled copies!

Neratec Solutions AG, CH-8608 Bubikon, Company Confidential Page 5 (7) 65.95mm 63.05mm 6.1mm 4.0mm 3.2mm m m 9 6 1

. m m 4 8 1

. m m 9

. 2 m m 5 6 8

. m m 5 3

. 4 3 m m 1

. 0 4 m m 0 3 4

. DT50RF (5127) Integration Manual Michael Aeschbacher 3 Regulatory Compliance 3.1 Applicable rules

- FCC Title 47 CFR For the module following FCC and ISED rules are applicable. o 15.107 o 15.109 o 15.205 o 15.207 o 15.209 o 15.407

- RSS 247 Issue 2

- RSS Gen Issue 5 3.2 FCC Part 15, Class B This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:

This device may not cause harmful interference and This device must accept any interference received, including interference that may cause undesired operation. FCC Warning: Any changes or modifications to this device not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. 3.3 Industry Canada This device complies with Industry Canada license exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement."

3.4 RF Exposure Antennas must have a greater distance than 20cm separation from transmitting antenna to the user body during normal operation conditions. Doc.-Name: DT50RF_Integrator_Manual.docx, V1.3, Doc.-No.: 5127.30.316 Document date: 2020-05-06 printed versions are uncontrolled copies!

Neratec Solutions AG, CH-8608 Bubikon, Company Confidential Page 6 (7) DT50RF (5127) Integration Manual Michael Aeschbacher 3.5 Professional Installation This module is intended for professional installation. 3.6 Antennas Regulatory Approval Conditions for using the module:

This device can be used with the following antennas Type Part number Manufacturer Gain Chains Dipole F51-N Tekfun 5GHz: 7.5dBi max 1, 2, 3 Patch SPA-5600/40/14/0/V_2 Huber & Suhner 5GHz: 14dBi max 1, 2 Patch SPA-5600/65/9/0/MIMO Huber & Suhner 5GHz: 9dBi max 1, 2, 3 Shark SPA-5600/45/12/10/V Huber & Suhner 5GHz: 12dBi max Patch SPA-5600/40/14/0/V_2 with filter Huber & Suhner 5GHz: 14dBi max 1, 2 1, 2 3.7 Module Co-location The antenna used with this module must not be co-located or transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi transmitter product procedures. Co-location with one additional DT50RF module is allowed. 3.8 Host product testing Host products shall be tested according to FCC Title 47 CFR Part 15 Subpart B. To set module into test modes the Atheros Radio Test Tool shall be used. As the module shall be used only in products developed and produced by Neratec, no instruction will be documented here. For more information contact Michael Aeschbacher. Doc.-Name: DT50RF_Integrator_Manual.docx, V1.3, Doc.-No.: 5127.30.316 Document date: 2020-05-06 printed versions are uncontrolled copies!

Neratec Solutions AG, CH-8608 Bubikon, Company Confidential Page 7 (7)

neratec wireless & embedded ISED/FCC Module Usage Declaration Receiver Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Certification and Engineering Bureau Innovation, Science and Economic Development Canada Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 Subject: Module Usage Declaration Date: May 06, 2020 FCC Certification Number: 2AEJD-103902-1-DT50 Only applicable for IC certification:

IC Company Number: 9301A HVIN (Hardware Version DT50RF_MK2_1 Identification Number):

HMN: (Host Marketing Name) -

TO WHOM IT MAY CONCERN UPN: 1039021DT50 PMN: (Product Marketing DT50RF_MK2 Name) FVIN: (Firmware Version 6.6 Identification Number) We hereby declare that the module mentioned above will be used only in products designed and manufactured by Neratec Solutions AG. The module itself is never sold on the market. Best Regards,

} Wo J ksi Harju ratec Solutions AG osswiesstrasse 29 8608 Bubikon (Switzerland)

+41 55 253 2000 Neratec Solutions AG Tel +41 55 253 2000 Rosswiesstrasse 29 Fax +41 55 253 2070 CH-8608 Bubikon infofaneratec.com Switzerland www.neratec.com

neratec wireless & embedded CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 April 14, 2020 TO WHOM IT MAY CONCERN Pursuant to Paragraphs 0.457 and 0.459 of the Commissions Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID Model name 2AEJD-103902-1-DT50 DT50RF_MK2 For the product stated above, we request permanent confidentiality for exhibits which contain Operational Description, Block Diagram, Schematics, Parts Lists or Tune Up Information. The above exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. If you have any questions, please feel free to contact me at the address shown below. Sincerely, Nps Jussi Harju Contact Person: Michael Aeschbacher, Neratec Solutions AG, Rosswiesstrasse 29, 8608 Bubikon (Switzerland), Phone +41 55 253 2000, Fax +41 55 253 2070, info@neratec.com

neratec wireless & embedded [Lielgutels ISED/FCC Modular Approval Statement Receiver Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21048 Certification and Engineering Bureau Innovation, Science and Economic Development Canada Spectrum Engineering Branch 3701 Carling Avenue, Building 94 Ottawa, Ontario K2H 8S2 Subject: Limited Modular Approval Statement Date: April 14, 2020 FCC Certification Number: 2AEJD-103902-

1-DT50 Only applicable for IC certification:

IC Company Number: 9301A UPN: 1039021DT50 HVIN (Hardware Version DT50RF_MK2_1 PMN: (Product Marketing DT50RF_MK2 Identification Number): Name) HMN: (Host Marketing Name) = FVIN: (Firmware Version 6.6 Identification Number) TO WHOM IT MAY CONCERN Pursuant to Annex D in RSP-100 Issue 11 January 2016 and CFR 15.212, we herewith declare for our module. Modular approval requirement

(a) The radio elements must have the radio frequency circuitry shielded. Physical/discrete and tuning capacitors may be located external to the shield, but must be on the module assembly.

*Please provide a detailed explanation if the answer is No.

(b) The module shall have buffered modulation/data input(s) (if such inputs are provided) to ensure that the module will comply with the requirements set out in the applicable RSS / part 15 under conditions of excessive data rates or over-

modulation.

*Please provide a detailed explanation if the answer is No.:

(c) The module shall have its own power supply regulation on the module. This is to ensure that the module will comply with the requirements set out in the applicable standard regardless of the design of the power supplying circuitry in the host device which houses the module.

*Please provide a detailed explanation if the answer is No. 4 Neratec Solutions AG Tel +41 55 253 2000 Rosswiesstrasse 29 Fax +41 55 253 2070 CH-8608 Bubikon infofaneratec.com Switzerland www.neratec.com neratec wireless & embedded ISED/FCC Modular Approval Statement

(d) The module shall comply with the provisions for external power amplifiers and antennas detailed in this standard. The equipment certification submission shall contain a detailed description of the configuration of highest antenna gain for each type of antenna.

*Please provide a detailed explanation if the answer is No.:

(e) The module shall be tested for compliance with the applicable standard in a stand-alone configuration, i.e. the module must not be inside another device during testing.

*Please provide a detailed explanation if the answer is No.: The module will always be used with DT50 baseboard, like it was tested.

(f) The module shall comply with applicable RSS-102 exposure requirements and any applicable FCC RF exposure requirement which are based on the intended configuration/integration in a host.

*Please provide a detailed explanation if the answer is No.:

Only applicable for FCC certification:

(g) The module must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number.

*Please provide a detailed explanation if the answer is No.:

(h) The modular transmitter complies with all applicable FCC rules. Instructions for maintaining compliance are given in the user instructions. If you have any questions, please feel free to contact us at the address shown below Best Regards, jes Harju

/Neratec Solutions AG Rosswiesstrasse 29 8608 Bubikon (Switzerland)

+41 55 253 2000 INFO for applicant: LMA may be granted when one or more of the requirements in the table above cannot be demonstrated. LMA will also be issued in those instances where applicants can demonstrate that they will retain control over the final installation of the device, such that compliance of the end product is assured. In such cases, an operating condition on the LMA for the module must state that the module is only approved for use when installed in devices produced by a specific manufacturer. When LMA is sought, the application for equipment certification must specifically state how control of the end product, into which the module will be installed, will be maintained, such that full compliance of the end product is always ensured. 2 Neratec Solutions AG Tel +41 55 253 2000 Rosswiesstrasse 29 Fax +41 55 253 2070 CH-8608 Bubikon info(@neratec.com Switzerland www.neratec.com