FCC ID: XIA-CFW2832 CBRS 5G Cat B Outdoor CPE

User Guide AurusPRO 5G Outdoor CPE 3GPP Release 16 Model CFW-2832 Doc No. UG01427 2 of 84 Important notice This device, like any wireless device, operates using radio signals which cannot guarantee the transmission and reception of data in all conditions. While the delay or loss of signal is rare, you should not rely solely on any wireless device for emergency communications or otherwise use the device in situations where the interruption of data connectivity could lead to death, personal injury, property damage, data loss, or other loss. Casa Systems accepts no responsibility for any loss or damage resulting from errors or delays in transmission or reception, or the failure of the Casa Systems AurusPRO Global 5G Outdoor CPE to transmit or receive such data. Safety and hazards Warning Do not connect or disconnect cables or devices to or from the USB port, SIM card tray, or Ethernet port in hazardous locations such as those in which flammable gases or vapours may be present, but normally are confined within closed systems; are prevented from accumulating by adequate ventilation; or the location is adjacent to a location from which ignitable concentrations might occasionally be communicated. Copyright Copyright 2022 Casa Systems. All rights reserved. The information contained herein is proprietary to Casa Systems. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of Casa Systems. Trademarks and registered trademarks are the property of Casa Systems or their respective owners. Specifications are subject to change without notice. Images shown may vary slightly from the actual product. Note This document is subject to change without notice. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 3 of 84 Document history This document applies to the following CPE model:

AurusPRO 5G Outdoor CPE CFW-2832 V e r . D o c u m e n t d e s c r i p t i o n D a t e v1.01 Initial document release for 3GPP Release 16 devices 23 September, 2022 Table i. Document revision history CFW-2832 User Guide UG01427 v1.01 23 September, 2022 4 of 84 Contents 1 Document overview ...................................................................................................................................................................... 7 1.1 1.2 1.3 Introduction .................................................................................................................................................................................................................. 7 Target audience ........................................................................................................................................................................................................... 7 Prerequisites ................................................................................................................................................................................................................. 7 1.3.1 Notation .................................................................................................................................................................................................................. 7 2 Product introduction ..................................................................................................................................................................... 8 2.1 2.2 Product overview ......................................................................................................................................................................................................... 8 Package contents ......................................................................................................................................................................................................... 8 3 Physical dimensions and interfaces ............................................................................................................................................ 9 3.1 3.2 3.3 3.4 Physical dimensions .................................................................................................................................................................................................... 9 3.1.1 CFW-2832 ............................................................................................................................................................................................................... 9 Interfaces .................................................................................................................................................................................................................... 10 3.2.1 CFW-2832 ............................................................................................................................................................................................................ 10 Insert SIM card .......................................................................................................................................................................................................... 11 Assemble and attach the mounting bracket ...................................................................................................................................................... 13 3.4.1 Mounting bracket assembly instructions .................................................................................................................................................... 13 3.4.2 Overview of completed mounting ................................................................................................................................................................. 16 4 Installing the AurusPRO .............................................................................................................................................................. 17 4.1.1 Installation considerations .............................................................................................................................................................................. 17 Determine the best location for the AurusPRO ................................................................................................................................................ 18 5G Smart Antenna Tool ........................................................................................................................................................................................... 19 4.3.1 Calibration ........................................................................................................................................................................................................... 19 Connect the 5G Smart Antenna Tool to the AurusPRO................................................................................................................................... 20 Perform site survey and installation ..................................................................................................................................................................... 21 Fix to mounting ......................................................................................................................................................................................................... 21 Antenna power supply weather seal .................................................................................................................................................................... 22 4.2 4.3 4.4 4.5 4.6 4.7 5 Setting up the AurusPRO............................................................................................................................................................ 27 5.1 5.2 Log in as Administrator via Web UI ...................................................................................................................................................................... 27 Confirming a successful connection .................................................................................................................................................................... 28 CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6 User interface .............................................................................................................................................................................. 29 5 of 84 6.1 6.2 6.3 6.2.2 Status ........................................................................................................................................................................................................................... 29 6.1.1 System information ........................................................................................................................................................................................... 30 6.1.2 Cellular connection status ............................................................................................................................................................................... 31 6.1.3 WWAN connection status ................................................................................................................................................................................ 32 6.1.4 Advanced status ................................................................................................................................................................................................ 33 6.1.5 Neighbouring cell information ....................................................................................................................................................................... 35 6.1.6 LAN ....................................................................................................................................................................................................................... 37 6.1.7 Bluetooth............................................................................................................................................................................................................. 37 6.1.8 GPS ....................................................................................................................................................................................................................... 38 6.1.9 NIT ......................................................................................................................................................................................................................... 39 Networking ................................................................................................................................................................................................................. 40 6.2.1 Wireless WAN ..................................................................................................................................................................................................... 40 6.2.1.1 Wireless WAN profiles .............................................................................................................................................................................................................. 40 6.2.1.2 Band selection ............................................................................................................................................................................................................................ 44 6.2.1.3 RAT selection .............................................................................................................................................................................................................................. 45 6.2.1.4 Operator settings ...................................................................................................................................................................................................................... 45 6.2.1.5 Roaming control......................................................................................................................................................................................................................... 46 6.2.1.6 Cell lock ........................................................................................................................................................................................................................................ 46 6.2.1.7 SIM security ................................................................................................................................................................................................................................. 48 LAN ....................................................................................................................................................................................................................... 49 6.2.2.1 LAN Configuration ..................................................................................................................................................................................................................... 49 6.2.2.2 DHCP configuration .................................................................................................................................................................................................................. 50 6.2.2.3 VLAN ............................................................................................................................................................................................................................................. 50 Firewall ................................................................................................................................................................................................................. 52 6.2.3.1 NAT................................................................................................................................................................................................................................................ 52 6.2.3.2 MAC whitelist .............................................................................................................................................................................................................................. 54 6.2.4 Routing ................................................................................................................................................................................................................. 55 6.2.4.1 Static Routing .............................................................................................................................................................................................................................. 55 6.2.5 Service assurance ............................................................................................................................................................................................. 57 6.2.5.1 Result ............................................................................................................................................................................................................................................ 57 Services ....................................................................................................................................................................................................................... 58 6.3.1 Network Time (NTP) .......................................................................................................................................................................................... 58 6.3.2 Aurora App (Bluetooth) Server ....................................................................................................................................................................... 59 6.3.3 TR-069 .................................................................................................................................................................................................................. 59 6.3.3.1 TR-069 configuration ................................................................................................................................................................................................................ 60 6.3.4 DNS Server .......................................................................................................................................................................................................... 61 6.3.5 Geofence ............................................................................................................................................................................................................. 62 6.3.5.1 Add Geofence ............................................................................................................................................................................................................................. 63 6.3.6 CBRS SAS ............................................................................................................................................................................................................. 65 6.3.6.1 Install parameters...................................................................................................................................................................................................................... 66 6.3.6.2 Debug parameters .................................................................................................................................................................................................................... 66 6.2.3 CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6 of 84 6.4 6.4.1 System ......................................................................................................................................................................................................................... 67 Log System log ................................................................................................................................................................................................ 67 6.4.1.1 Log System log settings ........................................................................................................................................................................................................ 67 6.4.1.2 QXDM over Ethernet ................................................................................................................................................................................................................. 69 6.4.2 Ping diagnostics ................................................................................................................................................................................................. 70 6.4.3 System configuration ........................................................................................................................................................................................ 71 6.4.3.1 Restore factory defaults ........................................................................................................................................................................................................... 71 6.4.3.2 Web server settings .................................................................................................................................................................................................................. 72 6.4.3.3 Administrator credentials ........................................................................................................................................................................................................ 73 6.4.3.4 Web UI credentials .................................................................................................................................................................................................................... 74 6.4.3.5 Settings backup/restore ........................................................................................................................................................................................................... 74 6.4.3.6 Runtime Configuration ............................................................................................................................................................................................................. 76 6.4.4 Firmware upgrade ............................................................................................................................................................................................. 77 6.4.5 Access control .................................................................................................................................................................................................... 78 6.4.6 Reboot ................................................................................................................................................................................................................. 79 6.4.7 Field test .............................................................................................................................................................................................................. 80 6.4.8 Encrypted Debug Information ........................................................................................................................................................................ 81 6.4.8.1 Generate ...................................................................................................................................................................................................................................... 81 6.4.8.2 Download .................................................................................................................................................................................................................................... 81 Appendix A Safety and compliance .................................................................................................................................................... 82 RF Exposure .............................................................................................................................................................................................................................. 82 FCC Statement ......................................................................................................................................................................................................................... 82 Operating temperature.......................................................................................................................................................................................................... 83 Company details ...................................................................................................................................................................................................................... 83 Product details ......................................................................................................................................................................................................................... 83 Appendix B Configuring Radio Access Technologies ....................................................................................................................... 84 CFW-2832 User Guide UG01427 v1.01 23 September, 2022 7 of 84 1 Document overview 1.1 Introduction This document provides you all the information you need to set up, configure and deploy the CFW-2832 in the Casa Systems AurusPRO Global 5G Outdoor CPE antenna. 1.2 Target audience This document is intended for experienced hardware installers who understand telecommunications terminology and concepts. 1.3 Prerequisites If local regulations require the use of a CBRS Spectrum Access Server then the AurusPRO Global 5G Outdoor CPE must be professionally installed by a Certified Professional Installer (CPI) in order to function. Before continuing with the installation of the CPE please confirm that you have:

A mobile device (tablet or smartphone) with the Aurora Installation application installed. Read the entire Safety and product care section of this document and RF Exposure information. You will also require wrenches or sockets and screwdrivers and other tools and materials depending on how you plan to mount the device. 1.3.1 Notation The following symbols may be used in this document:

Note This note contains useful information. Important This is important information that may require your attention. Warning This is a warning that may require immediate action in order to avoid damage or injury. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 8 of 84 2 Product introduction 2.1 Product overview Rural and regional homes and businesses, remote commercial sites and metropolitan fringe districts located beyond the reach of fixed line infrastructure rely on mobile networks to access broadband Internet. Designed to optimise signal strength in weak signal areas, the AurusPRO 5G Outdoor CPE is positioned on the exterior of the premises to overcome distance limitations and geographical obstructions and deliver high-speed 5G connectivity to wired and wireless clients in the property via an indoor router. 2.2 Package contents The in-box contents include:

1 x AurusPRO Global 5G Outdoor CPE 1 x Assembled mount bracket Accessories used in this solution (packaged separately):

1 x Antenna Power Supply (POE-03) used to power the AurusPRO during normal operation 1 x 5G Smart Antenna Tool used to power and provide a wireless interface to the AurusPRO 5G Outdoor CPE during installation. If any of these items are missing or damaged, please contact your sales representative immediately. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 9 of 84 3 Physical dimensions and interfaces 3.1 Physical dimensions 3.1.1 CFW-2832 Below are details of the layout and physical dimensions of the CFW-2832. Figure 1 CFW-2832 5G Outdoor CPE dimensions Height Width C F W - 2 8 3 2 D i m e n s i o n s 460mm (18.1 in) 335mm (13.2 in) Depth (excluding mount) 184mm (7.25 in) Weight (excluding mount) 2.875kg (6 lb 5.4 oz) Table 1 - CFW-2832 device dimensions CFW-2832 User Guide UG01427 v1.01 23 September, 2022 3.2 Interfaces 3.2.1 CFW-2832 Antenna Power Supply port (PoE) 10 of 84 Antenna panel 5G Smart Antenna Tool port SIM card access hatch I t e m Antenna panel Figure 2 Interfaces CFW-2832 D e s c r i p t i o n Includes 2 x pairs Cross polarised antennas and GPS antenna 5G Smart Antenna Tool port Connect the 5G Smart Antenna Tool here SIM hatch Open the hatch to insert SIM here Antenna Power Supply port (PoE) Provides power and data connectivity to the AurusPRO 5G Outdoor CPE with Ethernet cable Table 2 Interfaces CFW-2832 CFW-2832 User Guide UG01427 v1.01 23 September, 2022 11 of 84 3.3 Insert SIM card All models in the AurusPRO Global 5G Outdoor CPE series employ SIM cards in Micro-SIM (2FF) format. Follow the instructions below to insert a SIM card. 1 On the back of the AurusPRO, locate the SIM hatch. Using a screwdriver, unscrew the two screws on the SIM hatch then remove the cover to reveal the SIM card slot. Figure 3 - Removing screws from the SIM hatch Note Screws used to fix the SIM hatch vary, may be: T10 torx or Pozidriv Installer to provide correct screwdriver. 2 Swing the SIM card locking mechanism down to allow insertion of the SIM card. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 3 Place the SIM card into the tray as shown below. 12 of 84 4 Swing the locking mechanism up and ensure that it clips into place to secure the SIM card. Figure 4 Placing the SIM card into the SIM card reader 5 Replace the SIM hatch and seal, insert the two screws and firmly hand tighten them using a T10 torx or Pozidriv screwdriver. Figure 5 SIM card locked in place CFW-2832 User Guide UG01427 v1.01 23 September, 2022 3.4 Assemble and attach the mounting bracket The AurusPRO Global 5G Outdoor CPE series of antennas use the same mounting bracket (MKIT-00011-000). 13 of 84 Exploded view Assembled view Figure 6 Standard mounting bracket (MKIT-00011-000) Note Other types of mounting brackets are available, contact Casa Systems sales or product support if required.. 3.4.1 Mounting bracket assembly instructions 1 Place the mast bracket onto the antenna housing as shown below. Figure 7 Elevation control components CFW-2832 User Guide UG01427 v1.01 23 September, 2022 2 Insert the elevation setting bolt into the mast bracket, then place the washer and nut over the elevation setting bolt as shown below. 14 of 84 Elevation setting bolt Elevation setting bolt nut and washer Figure 8 - Attaching the mounting bracket to the AurusPRO 5G Outdoor CPE 3 Tighten the lock nut so that the mast bracket and antenna housing do not swivel easily. Do not overtighten the elevation setting bolt as some adjustment may be required later. Figure 9 - Assembling mast bracket to mast CFW-2832 User Guide UG01427 v1.01 23 September, 2022 4 Alternately tighten the left and right bracket bolts to maintain even pressure on the pipe, to 65 in-lb. 15 of 84 Figure 10 - Tightening bracket bolts CFW-2832 User Guide UG01427 v1.01 23 September, 2022 16 of 84 Antenna housing Elevation setting bolt 3.4.2 Overview of completed mounting Mast bracket Mast Left bracket bolt Bracket plate Right bracket bolt Figure 11 - CFW-2301 / CFW-2331 / CFW-2351 / CFW-2352 / CFW-2382 / CFW-2631 mounting bracket and bolts Notes on mounting:

Use a standard 13mm socket wrench for all bolts Tighten bolts to the following torque settings:

Elevation setting bolt: 7 Nm / 65 in-lbs Left and right bracket bolts: 7 Nm / 65 in-lbs Do not over-tighten bolts CFW-2832 User Guide UG01427 v1.01 23 September, 2022 4 Installing the AurusPRO The image below illustrates a typical installation of the AurusPRO 5G Outdoor CPE. 17 of 84 If required by local regulations Figure 12 - Typical AurusPRO 5G Outdoor CPE installation 4.1.1 Installation considerations Important If local regulations require the use of a CBRS Spectrum Access Server then the AurusPRO Global 5G Outdoor CPE must be professionally installed by a Certified Professional Installer (CPI) in order to function. As the AurusPRO 5G Outdoor CPE is aligned specifically for each individual property, please take note of the following when installing the equipment:

The Antenna Power Supply (POE-03) and Wi-Fi Gateway must be installed in a well-ventilated area and near a dedicated power outlet which allows easy visibility of the indicator lights. Use a high-grade CAT6 Ethernet cable which is suitable for outdoor use as it will be partially exposed to the elements. The equipment must be protected from running water, steam and excessive heat and must be installed according to the guidelines in this document. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 18 of 84 Keep trees and branches away from the AurusPRO 5G Outdoor CPE. After alignment, do not move, place anything in front of, or adjust the position of the AurusPRO 5G Outdoor CPE since this will likely have a negative impact on the signal quality and performance of the wireless service. If construction work has been carried out on the exterior of the property, the antenna may need to be re-

aligned to ensure the installation is still operating at peak performance. The AurusPRO 5G Outdoor CPEs location is determined by radio frequency performance and it may not be possible to relocate the antenna when moving to a new property. It is advised that a site survey be conducted before initiating the installation process. 4.2 Determine the best location for the AurusPRO Determining the best location for the AurusPRO 5G Outdoor CPE involves:

1 2 Performing a survey of the site using the 5G Smart Antenna Tool and Aurus Installation application. Consulting the customer about mounting location, grounding and cable routing based on results of the RF test, aesthetics and any planned renovations to the property. When selecting a location to mount the AurusPRO 5G Outdoor CPE, ensure that:

lock of the desired cell and optimal signal level is achieved. the mounting position is unobtrusive and aesthetically pleasing where possible. the mount/antenna is not closer than three feet from other antenna equipment. the customer has obtained local planning authority/homeowner association/zoning approval for installation if required. This is the sole responsibility of the customer. Where possible, avoid mounting the AurusPRO 5G Outdoor CPE so that it is aimed back over the roof of the property. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 19 of 84 4.3 5G Smart Antenna Tool Use a fully charged 5G Smart Antenna Tool to support site survey with the companion application for the best signal from a nearby cell tower. Push the power button on the 5G Smart Antenna Tool to turn it on. After a few seconds, the LEDs illuminate. On each start up, the 5G Smart Antenna Tool LEDs flash both red and green twice a second, indicating that the compass requires calibrating. 4.3.1 Calibration To calibrate the device, first isolate it from any magnetic field or metal structures (for example, vehicles, the antenna pole, power lines, etc) and then slowly and steadily rotate the unit fully through all three axes. See the diagrams below. The LEDs stop flashing when calibration has been performed successfully. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 20 of 84 4.4 Connect the 5G Smart Antenna Tool to the AurusPRO Important The AurusPROs Ethernet power cable SHOULD NOT BE CONNECTED to the Antenna Power Supply (POE-03) during this scanning process. The power required during the scanning process will be supplied by the 5G Smart Antenna Tool. Ensure that the 5G Smart Antenna Tools battery is fully charged before commencing the scanning process. 1 Turn the plug on the console port hatch counter-clockwise so that it is in the unlocked (vertical) position as shown in the image below. 2 Pull the plug out to reveal the console port. Figure 13 - Unlocked console port hatch CFW-2832 User Guide UG01427 v1.01 23 September, 2022 3 Remove the cap from the head of the 5G Smart Antenna Tool and insert it into the console port as shown in the picture below. Figure 14 - Console port 21 of 84 Figure 15 - Attached 5G Smart Antenna Tool 4.5 Perform site survey and installation 1 Pair your smartphone to the 5G Smart Antenna Tool over Bluetooth. The Bluetooth ID is printed on the label of the 5G Smart Antenna Tool. 2 Open the Installation app and follow the instructions in the app to complete the installation. 4.6 Fix to mounting When you have found the best spot to install the AurusPRO, install the mount (pole, j-mount, etc.) using appropriate materials. Securely fix the antenna to the mount facing the direction as indicated by the app, refer to section 3.4.2 Overview of completed mounting, above, for additional mounting details. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 22 of 84 4.7 Antenna power supply weather seal The AurusPRO power supply weather seal must be properly attached to prevent dust and water from entering the AurusPROs housing. To connect a PoE Ethernet cable through the power supply weather seal:

1 The power supply weather seal is shipped assembled and screwed into the AurusPRO 5G Outdoor CPE antenna housing. The five components of the weather seal assembly have to be separated in order to pass the cable through the weather seal during the installation process. Body Sealing washer Cable seal Collar Clamp Figure 16 - Weather seal in five parts Disassemble weather seal as follows:

a Twist the assembled weather seal counter-clockwise to remove it from the antenna housing. b Unscrew the clamp from the body and remove the sealing washer and the collar and cable seal assembly from inside the clamp. c Separate the cable seal and collar. Figure 17 - collar and cable seal CFW-2832 User Guide UG01427 v1.01 23 September, 2022 2 Push the Ethernet cable through the hole in the clamp, as shown below. 23 of 84 3 Place the collar over the Ethernet cable as shown, making sure that the teeth are facing the clamp. Figure 18 - Ethernet cable passed through clamp Figure 19 Collar placed over Ethernet cable 4 Pry open the split in the rubber and place the cable seal over the Ethernet cable with the wide end toward the RJ45 plug and away from the collar and clamp. See the image below for the correct orientation. Figure 20 - Cable seal placed over Ethernet cable The rubber cable seal has a split that may be difficult to detect. If the split is not obvious, roll the cable seal between your fingers to crack the split so that you can slip it over the cable. Note Do not use a sharp blade to open the split or cut another. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 5 Push the collar over the cable seal to prevent it from coming apart (the teeth will fit into an indentation near the clamp end of the cable seal). 24 of 84 6 Place the sealing washer over the Ethernet cable as shown below. Figure 21 Collar placed over the cable seal Figure 22 Sealing washer placed over Ethernet cable Important Ensure that the side of the sealing washer with a protruding inside lip is facing the clamp and the side with an protruding outside lip faces the body. 7 Push the Ethernet cable through the body as shown below. Figure 23 - Body placed over Ethernet cable CFW-2832 User Guide UG01427 v1.01 23 September, 2022 8 Plug the Ethernet cable into the Ethernet port of the CPE. 25 of 84 Figure 24 - Plugging in the Ethernet cable 9 Put the body into the opening on the CPE antenna housing and turn the body clockwise until it locks in place. 10 Push the cable seal and collar along the Ethernet cable into the body. Figure 25 - Cable seal and collar inserted into neck CFW-2832 User Guide UG01427 v1.01 23 September, 2022 11 Turn the clamp clockwise to tighten the sealing washer against the housing and to allow the cable seal and collar to compress and grip the cable to prevent dust and moisture entering the unit. Continue turning the clamp until tightly assembled. 26 of 84 Figure 26 - Turn the clamp clockwise until tight CFW-2832 User Guide UG01427 v1.01 23 September, 2022 27 of 84 5 Setting up the AurusPRO The AurusPRO Global 5G Outdoor CPE series of antennas use the same firmware. The AurusPRO comes with pre-configured settings that should suit most customers. For advanced configuration, log in to the web-based user interface of the AurusPRO as an administrator. 5.1 Log in as Administrator via Web UI To log in to the web-based user interface:

1 Open a web browser (e.g. Chrome, Safari, etc.), type http://192.168.1.1 into the address bar and press Enter. 2 The web-based user interface Login screen is displayed. Figure 27 Log in prompt for the web-based user interface 3 Enter the login User Name and User Password. A d m i n i s t r a t o r a c c o u n t User Name User Password root admin Table 3 - Management account login details Administrator account CFW-2832 User Guide UG01427 v1.01 23 September, 2022 5.2 Confirming a successful connection To confirm the connection status, click the Status menu item at the top of the page to display the Status page. Select the CELLULAR CONNECTION STATUS and WWAN CONNECTION STATUS items to expand them. 28 of 84 The details of the connection are displayed. Figure 28 - Main menu items Figure 29 - Cellular Connection Status and WWAN Connection Status If the device is connected, the Status field displays up. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 29 of 84 6 User interface The AurusPRO features a user interface with top and left-sided menus. The menu across the top of the screen is the highest-level menu. There are four main menu items: Status, Networking, Services and System The Networking, Services and System menus each feature a submenu on the left of the screen that allow you to navigate to different features within that area. The Status screen is somewhat different in that it contains various windows which can be expanded to display information about the device. 6.1 Status The Status page of the web interface provides system related information and is displayed when you log in to the AurusPRO management console. Figure 30 - The Status menu page upon first log in The status page has links to pages displaying SYSTEM INFORMATION CELLULAR CONNECTION STATUS WWAN CONNECTION STATUS ADVANCED STATUS NEIGBOURING CELL INFORMATION LAN details BLUETOOTH MAC address details GPS connection details NIT Smart Antenna Tool readings Toggle the display of the sections by clicking the or buttons to show or hide them. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.1.1 System information 30 of 84 Figure 31 - System Information S y s t e m I n f o r m a t i o n System up time The current uptime of the AurusPRO. Device name The manufacturers name of this device. Model The manufacturers model number. Hardware version The hardware version of the AurusPRO. Serial Number The serial number of the AurusPRO. Firmware version The firmware version of the AurusPRO Model The type of phone module Module firmware The firmware revision of the phone module. IMEI The International Mobile Station Equipment Identity number used to uniquely identify a mobile device. Table 4 - System Information fields CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.1.2 Cellular connection status 31 of 84 Figure 32 - Cellular Connection Status C e l l u l a r C o n n e c t i o n S t a t u s SIM status Displays the activation status of the AurusPRO on the carrier network. Signal strength (dBm) The current signal strength measured in dBm. Network registration status The status of the AurusPROs registration for the current network. Operator selection The mode used to select an operator network. Provider The current operator network in use. Roaming status The roaming status of the AurusPRO. Allowed bands The bands to which the AurusPRO may connect. Current band The current band being used by the AurusPRO. Coverage The type of mobile coverage being received by the AurusPRO. Table 5 - Cellular Connection Status fields CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.1.3 WWAN connection status 32 of 84 Figure 33 - WWAN Connection Status W W A N C o n n e c t i o n S t a t u s Profile name The name of the active profile. Status IPv6 status WWAN IP DNS server WWAN IPv6 The IPv4 connection status of the active profile. The IPv6 connection status of the active profile. The IPv4 address assigned by the mobile broadband carrier network. The primary and secondary IPv4 DNS servers for the WWAN connection. The IPv6 address assigned by the mobile broadband carrier network. IPv6 DNS server The primary and secondary IPv6 DNS servers for the WWAN connection. APN The Access Point Name currently in use. Connection uptime The length of time of the current mobile connection session. Max DL Max UL Current DL Current UL Maximum download speed in Kbps (Kilobits Per Second) Minimum upload speed in Kbps (Kilobits Per Second) Current download speed in Kbps (Kilobits Per Second) Current upload speed in Kbps (Kilobits Per Second) Table 6 - WWAN Connection Status fields CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.1.4 Advanced status 33 of 84 Figure 34 - Advanced Status CFW-2832 User Guide UG01427 v1.01 23 September, 2022 34 of 84 A d v a n c e d s t a t u s Mobile country code The Mobile Country Code (MCC) of the AurusPRO. Mobile network code The Mobile Network Code (MNC) of the AurusPRO. SIM ICCID IMSI The Integrated Circuit Card Identifier of the SIM card used with the AurusPRO, a unique number up to 19 digits in length. The International Mobile Subscriber Identity is a unique identifier of the user of a cellular network. Packet service status Displays whether the packet service is attached or detached. When APN or username/password is changed, the device detaches and reattaches to the network. N o n - N R 5 G ECGI eNodeB Cell ID PCI Channel number

(EARFCN) Reference Signal Received Power (RSRP) Reference Signal Received Quality (RSRQ) E-UTRAN Cell Global Identifier. The globally unique identity of a cell in E-UTRA. The ECGI concatenates the PLMN-Id and the ECI (E-UTRAN Cell Identifier). The ECI concatenates the eNodeB ID and the Cell ID Also known as the Evolved Node B, this is the hardware element in the LTE network that communicates directly with mobile devices. A unique code that identifies the base station from within the location area of the current mobile LTE network signal. Physical Cell ID of the LTE Cell. The channel number of the current cellular connection. A cell-specific reference signal used to determine RSRP. RSRQ calculates signal quality taking into consideration the RSSI. It is calculated by N x RSRP / RSSI where N is the number of Physical Resources Blocks (PRBs) over which the RSSI is measured. CQI Channel Quality Indicator. This is a value between 1 and 15 with 15 being the highest rating. Scell band Scell PCI The frequency band of the Scell. The Physical Layer Cell Identity (PCI) of the Scell. Scell channel number

(EARFCN) The E-UTRA Absolute Radio Frequency Channel Number (EARFCN) will uniquely identify the LTE band and carrier frequency. N R 5 G NCGI NR Cell Global Identifier. This concatenates the PLMN-Id (PLMN Identifier) and the 36bit NCI (NR Cell Identity). This information is not available when the device is operating in LTE or 5G Non-Standalone mode. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 35 of 84 gNodeB gNB CellID The gNodeB (gNB) is the term given to network equipment that transmits and receives wireless communications between UE and a mobile network A unique code that identifies the base station from within the location area of the current mobile 5G network signal. This is not available when the device is operating in LTE or 5G Non-Standalone mode. gNB PCI Physical Cell ID of the 5G NR Cell. Channel number NR ARFCN) Reference Signal Received Power (SS-

RSRP) Reference Signal Received Quality (SS-

RSRQ) The channel number of the current 5G cellular connection. Synchronisation Signal Reference Signal Received Power (SS-RSRP). The linear average over the power contributions (in Watts) of the resource elements that carry Secondary Synchronisation Signal (SSS). Secondary Synchronisation Signal Reference Signal Received Quality. SS-RSRQ calculates signal quality taking into consideration the RSSI. It is calculated by N x SS-RSRP / NR carrier RSSI where N is the number of Physical Resources Blocks

(PRBs) over which the NR RSSI is measured. NR CQI The 5G NR Channel Quality Indicator (CQI). Synchronisation Signal Block (SSB) Index This is a key part of beam management. It is a value comprised of Primary Synchronisation Signal (PSS), Secondary Synchronisation Signal (SSS) and the Physical Broadcast Channel (PBCH). Table 7 - Advanced Status fields 6.1.5 Neighbouring cell information Figure 35 - Cell Information N e i g h b o u r i n g c e l l I n f o r m a t i o n PCI EARFCN The Physical Cell ID. E-UTRA Absolute Radio Frequency Channel Number. Uniquely identifies the LTE Band and carrier frequency. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 36 of 84 RSRP RSRQ Serving LAN Reference Signal Received Power (RSRP). Reference Signal Received Quality (RSRQ). The radio signal being served e.g. 5G NR, LTE. Table 8 - Cell Information fields Figure 36 - LAN Information L A N c o n f i g u r a t i o n IP The IP address of the AurusPRO. Subnet mask The subnet mask of the AurusPRO. Hostname The label used to identify the device. Table 9 - LAN Information fields CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.1.6 LAN Click the LAN submenu under LAN to view the LAN connection information. 37 of 84 Figure 37 - LAN Information L A N IP The IP address and subnet mask of the AurusPRO. MAC address The MAC address of the AurusPRO. Ethernet port status Displays the current status of the Ethernet port and its operating speed. IP passthrough host MAC The MAC address of the connected gateway. Table 10 - LAN Information fields 6.1.7 Bluetooth Figure 38 - Bluetooth Information B l u e t o o t h MAC address The MAC address of the Bluetooth module. Table 11 - Bluetooth Information fields CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.1.8 GPS When a Global Positioning System signal is accessed, its details will display in the GPS page. 38 of 84 Figure 39 - GPS signal Information G P S Latitude Longitude The angular distance of a place north or south of the earth's equator, usually expressed in degrees and minutes The angular distance of a place east or west of the Greenwich meridian, usually expressed in degrees and minutes. Altitude The height of an object or point in relation to sea level or ground level. Height of geoid PDOP The height of an object from sea level if the Earth was under the influence of gravity and its own rotation alone. Position Dilution of Precision. Possible error in location due to GPS satellite location. Horizontal uncertainty Possible error in horizontal (latitude/longitude) location due to GPS satellite location. Vertical uncertainty Possible error in altitude location due to GPS satellite location. Table 12 - GPS signal Information fields CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.1.9 NIT Click the NIT to view the antennas Azimuth and Downtilt values as measured by the Smart Antenna Tool. 39 of 84 Figure 40 NIT Information CFW-2832 User Guide UG01427 v1.01 23 September, 2022 40 of 84 6.2 Networking 6.2.1 Wireless WAN 6.2.1.1 Wireless WAN profiles Important Changing any of these settings can cause the AurusPRO to lose Internet connectivity. Please do not change any of these settings unless instructed to do so. The Wireless WAN profiles page allows you to configure and enable/disable connection profiles. To access this page, click the Networking menu, and then select Wireless WAN profiles from the menu on the left. Table 13 - Wireless WAN Profiles page CFW-2832 User Guide UG01427 v1.01 23 September, 2022 41 of 84 Each profile refers to a set of configuration items which are used by the AurusPRO to activate a Packet Data

(PDP) context. Under normal scenarios, you may have a single profile enabled. Multiple profiles can be used for simple fast switching of PDP settings such as APN, or for advanced networking configuration where multiple simultaneous PDP contexts may be required. Use the Status On/Off button to select the profile to use. Use the IP Passthrough On/Off button to allow or restrict IP Passthrough when the respective profile is in use. Specify the path to map from LAN to VLAN in the Map to LAN/VLAN drop down menu. The options are: None, bridge0 or a VLAN Note When mapping a profile to the LAN, Bridge0 should be chosen. Important The same VLAN MUST NOT be used in multiple profiles, even if the other profile or profiles are not enabled. The Profilename and APN are defined when the Wireless WAN profile settings are configured, see next section. Configuring a Wireless WAN profile 1 2 Click the edit button corresponding to the Profile that you wish to create or modify. The Wireless WAN Profile settings page is displayed. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 42 of 84 I t e m Enable Name APN Username Password Figure 41 - Wireless WAN Profile Settings D e f i n i t i o n Toggle the enable button to On or Off, as desired. The name of the APN for easy identification on the Wireless WAN profile page. This name is only used to identify the profile on the AurusPRO. Enter the APN (Access Point Name) configured for the corresponding profile. The username used to log on to the corresponding APN (if required).. The password used to log on to the corresponding APN (if required).. Authentication type The authentication type required by your provider. This can be set to: None, PAP or CHAP CFW-2832 User Guide UG01427 v1.01 23 September, 2022 I t e m D e f i n i t i o n PDP Type Select the PDP type (IP protocol) to use for the connection. 43 of 84 a IPv4 Sets a single stack IPv4 connection through which the AurusPRO receives only IPV4 network and DNS addresses. b IPv6 Sets a single stack IPv6 connection through which the AurusPRO receives only IPV6 network and DNS addresses. Note Before selecting this PDP type, check with your carrier to confirm that single stack IPV6 connectivity is supported. c IPv4v6 Sets a dual stack connection allowing simultaneous IPV4 and IPV6 network connectivity. The AurusPRO receives both IPv4 and IPV6 network and DNS addresses. This is the default PDP type Allow Admin Access Select enable if remote SSH, TR-069 or WebGUI access to the device should be possible via this Wireless WAN Profile. Note SSH/HTTP/HTTPS can be individually restricted in the Access Control menu. Note also that this will automatically be enabled if the profile is selected in the TR-069 settings menu. MTU size Sets the Maximum Transmission Unit size. This may be from 1 to 1500 bytes. IP passthrough Allows a downstream device, such as a router, to manage the connection. The downstream device connects to the Internet and receives a WAN IP address so that all Internet traffic is passed to the downstream device. Internet traffic is still terminated at the gateway (AurusPRO) and passed through to a downstream device, so the carrier is still able to connect to the gateway. Save button Click the Save button to apply the changes. Table 14 - Wireless WAN Profile Settings page CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.2.1.2 Band selection Select individual bands from the following band groupings: LTE, NR5G NSA or NR5G SA 44 of 84 Figure 42 - Wireless WAN Band selection page To set a device up for different LTE, 5G Non-Standalone (NR5G NSA) and 5G Standalone (NR5G NSA) modes, refer to: Appendix B Configuring Radio Access Technologies CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.2.1.3 RAT selection Select the preferred RAT (Radio Access Technology) from the following: LTE or NR5G 45 of 84 Figure 43 - Wireless WAN Radio Technology selection page To set a device up for different LTE, 5G Non-Standalone (NR5G NSA) and 5G Standalone (NR5G NSA) modes, refer to: Appendix B Configuring Radio Access Technologies 6.2.1.4 Operator settings The Operator setting screen lets you select whether to have the AurusPRO automatically select the most appropriate operator and access technology, or if you set it to Manual, you can override and lock it to a particular carrier or access technology. Figure 44 - Wireless WAN Operator Settings CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.2.1.5 Roaming control Select On to enable Roaming Control. 46 of 84 Figure 45 - Roaming control page 6.2.1.6 Cell lock The Cell lock function allows you to specify a list of cells that the AurusPRO will not deviate from. Two types of cells can be locked: LTE and NR5G Figure 46 Cell Lock page Adding an LTE cell lock To add an LTE cell to the list:

1 Next to LTE Cell Lock List, click on the Add button 2 Enter the PCI and EARFCN values of the cell that you want to lock to. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 47 of 84 Figure 47 - LTE Cell Lock settings 3 4 Click on the Save button. It will be added to the LTE Cell Lock List on the Cell Lock page. Repeat steps 1 to 3 for all the LTE cells that you wish to add. Adding an NR cell lock To add an NR5G cell to the list:

1 Next to the NR5G Cell Lock List, click on the Add button. 2 Enter the gNB, NR ARFCN, Subcarrier Spacing and NR SA band values for the NR5G cell that you want to lock to. Figure 48 NR5G Cell Lock settings 3 4 Click on the Save button. It will be added to the NR5G Cell Lock List on the Cell Lock page. Repeat steps 1 to 3 for all the NR5G cells that you wish to add. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 48 of 84 6.2.1.7 SIM security The SIM security settings page can be used for authenticating SIM cards that have been configured with a security PIN. Unlocking a PIN locked SIM If the SIM card is locked, you will receive a notice when you access the Status page after which you will be directed to the PIN settings page to enter the PIN. The PIN settings page lists the status of the SIM at the top of the page. If you are not redirected to the PIN settings page, to unlock the SIM:

1 Click on the Networking menu from the top menu bar, and then click SIM security settings. Figure 49 - Wireless WAN SIM Security settings page 1 2 Enter the PIN in the Current PIN field (enter numbers only). Click on the Save button to save the PIN and unlock access. 3 Once unlocked, you may toggle the PIN protection switch to the Off position if you no longer wish to have access locked by a PIN. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 49 of 84 6.2.2 LAN 6.2.2.1 LAN Configuration The LAN configuration page is used to configure the LAN settings of the AurusPRO. To access the LAN configuration page, click the Networking menu at the top of the screen, then click the LAN menu on the left. The default IP of the LAN port is: 192.168.1.1 with subnet mask: 255.255.255.0 To change the IP address or Subnet mask, enter the new IP Address and/or Subnet mask and click the Save button. Note If you change the IP address, remember to refresh the Ethernet interface of your device, or set an appropriate IP address range, then enter the new IP address into your browser address bar to access the AurusPRO. Figure 50 - LAN Configuration page CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.2.2.2 DHCP configuration You can manually set the start and end address range to be used to automatically assign to DHCP clients when they are connected and the lease time of the assigned addresses. 50 of 84 Enter the desired DHCP options and click the Save button. Figure 51 - DHCP Configuration page 6.2.2.3 VLAN A Virtual Local Area Network (VLAN) is a subnetwork used to group devices located on separate physical networks. This useful feature allows you to partition your network without the need for additional cabling or wireless access. Figure 52 - VLAN Rules list page CFW-2832 User Guide UG01427 v1.01 23 September, 2022 51 of 84 VLAN Settings Note VLANs can only be assigned to APN Profiles 2-6. Click the Add button in the VLAN RULES section to create a VLAN rule:

1 Click the +Add button on the VLAN Configuration page. The VLAN Settings page will open:

Figure 53 - VLAN Settings page 2 3 In the Rule name field, enter a name for the VLAN rule. This is a name that allows you to easily identify the VLAN. In the VLAN ID field, enter a number between 0 and 4094 which will be used by the network to identify the VLAN uniquely. Note The values 253, 254 and 255 are reserved and cannot be assigned to VLANs as VLAN IDs. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 52 of 84 4 5 6 7 8 In the IP address field, enter the IP address for this device on the VLAN. In the Subnet mask field, enter the Subnet mask for the device on the VLAN. In the DHCP start range and DHCP end range fields, enter the IP address range for the VLAN. Addresses within this range will be assigned automatically to devices connecting to this VLAN. In the DHCP lease time (seconds) field, enter the number of seconds that the DHCP lease will be valid for. This value must be 120 or higher. In the Allow Admin Access field, select Enable ON if local SSH or WebGUI access to the device should be possible via this VLAN. Note SSH/HTTP/HTTPS can be individually restricted in the Access Control menu. 9 Set the Enable toggle to the ON position. 10 Click the Save button to apply the settings. 6.2.3 Firewall 6.2.3.1 NAT The Port forwarding list is used to configure the Network Address Translation (NAT) rules currently in effect on the AurusPRO. To access the Port forwarding page, click the Networking menu at the top of the screen, click the Firewall menu on the left. Figure 54 NAT Port forwarding list The purpose of the port forwarding feature is to allow mapping of inbound requests to a specific port on the WAN IP address to any connected device. Note Some carriers block inbound connections, or require a public IP address in order to get inbound requests. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 Adding a port forwarding rule To create a new port forwarding rule:

1 Next to the protocol you wish to create a rule for (IPv4 or IPv6), click the +Add button. The port forwarding settings screen is displayed. 53 of 84 In the Rule name field, enter a name for the rule so that it can be easily identified. Figure 55 - Port Forwarding Settings In the Profile No. field, enter a number that corresponds to the Wireless WAN Profile that you want to use for the rule. 2 3 4 Use the Protocol drop-down list to select the type of protocol you want to use for the rule. The protocols selections available are TCP, UDP and TCP/UDP. 5 6 7 In the Public port field, enter a number between 1 and 65535 to use for the communication port from the AurusPRO out to the mobile network. In the Local IP Address / Local IPv6 Address field, enter the IP address of LAN equipment to which traffic should be routed or a wildcard IP address (0.0.0.0) that allows all IP addresses to access the traffic. In the Local port field, enter a port number to use for traffic to the local device. This may be an integer between 1 and 65535. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 54 of 84 8 9 Ensure that the Enable toggle button is set to the ON position. Click the Save button to confirm your settings. 10 To delete a port forwarding rule, click the button on the Port forwarding list for the corresponding rule that you would like to delete. To edit an existing rule, click the button. 6.2.3.2 MAC whitelist The MAC filter feature allows you to apply a policy to the traffic that passes through the router, both inbound and outbound, so that network access can be controlled based on the MAC address of the device seeking to make a connection. To access the MAC filtering page, click the Networking menu at the top of the screen, click the Firewall menu on the left, then click the MAC whitelist menu item. Figure 56 MAC whitelist page To filter access based on MAC address:

1 2 3 4 Enter a Name to reference the whitelisted device with. Enter the MAC address you want to allow access to Click the Enable toggle key so that it is in the On position. Click the Save button. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 55 of 84 6.2.4 Routing 6.2.4.1 Static Routing To view the Static Routing settings, click Networking then Routing > Static menu on the left. The Static Routing page contains details of defined Static Routing Lists and well as the Active Routing list. Click the Add button to define a new Static Routing List. Figure 57 Static/Active routing list Static Route Configuration Click the Add button to open the ROUTE CONFIGURATION page:

CFW-2832 User Guide UG01427 v1.01 23 September, 2022 56 of 84 Figure 58 Route configuration page R o u t e c o n f i g u r a t i o n Route name Enter a meaningful name. Destination IP address Enter the destination IP address of the route. Netmask Enter a netmask specification. Gateway IP address Enter the gateways IP address Network interface Select the Network interface. Metric Enter a metric in the range of 0 through 32766 Save button Click to save the changes and add the configuration to the Static Routing List. Cancel button Close the window and discard the current entries. Note if you want to delete an existing Static Route, click the the Static Routing List to remove it permanently from the system. delete button on Table 15 Route configuration fields CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.2.5 Service assurance To conduct a check on general status of selected WWAN profiles and other tests click the Networking menu at the top of the screen, then click the Service assurance menu item on the left. 57 of 84 Figure 59 Service assurance page From the WWAN profiles list select the service you want to monitor. When the settings are complete, click the Start button to commence the test. 6.2.5.1 Result In this section the Status, Progress stage and any Error message will be displayed. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 58 of 84 6.3 Services 6.3.1 Network Time (NTP) The NTP (Network Time Protocol) settings page allows you to configure the AurusPRO to synchronize its internal clock with a global Internet Time server and specify the time zone for the location of the device. This provides an accurate timekeeping function for features such as System Log entries and Firewall settings where the current system time is displayed and recorded. Any NTP server available publicly on the internet may be used. The default NTP server is time.nrc.ca. To access the Network time (NTP) page, click the Services menu at the top of the screen then click the Network time (NTP) menu item on the left. Figure 60 - Network Time (NTP) page CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.3.2 Aurora App (Bluetooth) Server The Aurora App (Bluetooth) Server is used to facilitate communication with the Aurora smartphone installation app. Switch Enable to On before starting the Aurora installation app on an Android device. 59 of 84 Figure 61 - Aurora App (Bluetooth) server page When an installation has been completed, you have the option to disable the Aurora App server, but be aware that next time you try to find the antenna via the app, it will not be able to discover the antenna until the Aurora App server has been re-enabled. 6.3.3 TR-069 The TR-069 (Technical Report 069) protocol is a technical specification also known as CPE WAN Management Protocol (CWMP). It is a framework for remote management and auto-configuration of end-user devices such as customer-premises equipment (CPE) and Auto Configuration Servers (ACS). It is particularly efficient in applying configuration updates across networks to multiple CPEs. TR-069 uses a bi-directional SOAP/HTTP-based protocol based on the application layer protocol and provides several benefits for the maintenance of a field of CPEs:

Simplifies the initial configuration of a device during installation Enables easy restoration of service after a factory reset or replacement of a faulty device Firmware and software version management Diagnostics and monitoring You must have your own compatible ACS infrastructure to use TR-069. To access and configure the TR-069 settings, you must be logged into the router with the root account. Note When a factory reset of the router is performed via TR-069, the TR-069 settings are preserved. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 The CPE sends inform messages periodically to alert the ACS server that it is ready. These inform messages can also be configured to accept a connection request from the ACS server. When a connection is established, any tasks queued on the ACS server are executed. These tasks may be value retrieval or changes and firmware upgrades. 60 of 84 6.3.3.1 TR-069 configuration To configure TR-069:

1 Click the Enable TR-069 toggle key to switch it to the ON position. Figure 62 - TR-069 Configuration CFW-2832 User Guide UG01427 v1.01 23 September, 2022 61 of 84 2 In the ACS URL field, enter the Auto Configuration Servers full domain name or IP address. 3 Use the ACS username field to specify the username used by the server to authenticate the CPE when it sends an inform message. 4 5 6 7 8 9 In the ACS password and Verify ACS password fields, enter the password used by the server to authenticate the CPE when it sends an inform message. In the Connection request username field, enter the username that the CPE uses to authenticate the Auto Configuration Server during a connection request to the CPE. In the Connection request password and Verify password fields, enter the password that the CPE uses to authenticate the Auto Configuration Server during a connection request to the CPE. The inform message acts as a beacon to inform the ACS of the existence of the router. Select Enable periodic ACS informs toggle key to ON in order to turn on the periodic ACS inform messages. In the Inform Period field, enter the number of seconds between the inform messages. Click the Save button to save the settings. 6.3.4 DNS Server Enter the IP addresses of the Primary DNS server and Secondary DNS server. Figure 63 - DNS Server page Set a DNS cache size of between 0 and 5000. Set the DNS local TTL (Time-To-Live) time between 0 and 86,400 seconds. Click the Save button to apply the settings to the DNS server. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 62 of 84 6.3.5 Geofence To access the Geofence screen, select the Services item from the top menu bar then select the Geofence menu item. Geofence allows you to designate a circular area and then uses the routers GPS position to monitor when the gateway moves out of or in to that area. Figure 64 Geofence options I t e m D e s c r i p t i o n GEOFENCE CONFIGURATION Enable button Toggles Geofence operation On or Off. When on your currently defined Geofences appear in the Geofence list, see below. Coordinate units Select either:

DMS (Degrees/Minutes/Seconds), or Decimal degrees Changing this will change the display in the GEOFENCE LIST lower on the page, and the GEOFENCE CONFIGURATION page, see below. Measurement system Select either:

metric, or imperial CFW-2832 User Guide UG01427 v1.01 23 September, 2022 63 of 84 Changing this will change the display in the GEOFENCE LIST lower on the page, and the GEOFENCE CONFIGURATION page, see below. Save button Add button Saves any changes made on this page Click to add a new Geofence definition. The add Geofence configuration screen will open, see next section below. GEOFENCE LIST This table contains all your currently defined Geofences. Name A user defined reference name. Latitude / Longitude The Latitude and Longitude coordinates defined in the GEOFENCE CONFIGURATION page display. The Coordinate units selection will determine which system displays: DMS or decimal degrees Radius Set a radius from the centre of the geofence point. The Measurement system selection will determine which system displays:

Kilometres or miles Status In if the router is inside the radius. Out if the router is outside the radius. Edit button Click this to edit an existing Geofence in the list. The user interface is the same as the add Geofence configuration screen, see next section below. Delete button Click to remove the geofence from the list. Table 16 Geofence user interface 6.3.5.1 Add Geofence Click the +Add button to create a new Geofence (note that editing an existing Geofence uses the same configuration page). Figure 65 Configure Geofences CFW-2832 User Guide UG01427 v1.01 23 September, 2022 64 of 84 I t e m Name D e s c r i p t i o n When you Add a new Geofence you will be prompted to enter a meaningful name. This will be its reference in the Geofence list page. Latitude / Longitude Enter the Latitude and Longitude coordinates of the centre of the geofence. The Coordinate units selection will determine which system displays: DMS or decimal degrees Radius Set a radius from the centre of the geofence point for the fence line. The Measurement system selection will determine which system displays:

Kilometres or miles Open Google Maps button When coordinates have been entered, click the Google maps button to show where you expect the centre of the geofence to be. For example:

Save button Saves the new Geofence (Add) or saves the changes to an existing Geofence (Edit). Cancel button Closes the Add/Edit page and returns to the Geofence list without saving any changes. Table 17 Geofence configuration options CFW-2832 User Guide UG01427 v1.01 23 September, 2022 65 of 84 6.3.6 CBRS SAS CBRS (Citizens Broadband Radio Service) was introduced in the USA in 2016 to prioritise use of 3.5 GHz band spectrum (35503700 MHz) so that access to the spectrum could be prioritised into three levels to prevent harmful interference to higher priority users. The highest priority is reserved for government/military purposes and then the next level for Priority Access Licensed (PAL) users. Other users (General Authorized Access users) must request access to use the spectrum via the SAS (Spectrum Access Server). Currently this functionality only applies to devices in service in USA. The Spectrum Access System (SAS) is a cloud-based service that manages devices transmitting in the CBRS band. A CBRS device (CBSD) needs authorization from the SAS before it starts to transmit in the CBRS band. The authorization process must be performed by a Certified Professional Installer (CPI) using the Aurora Pro installation app on an Android mobile phone or other device. Never attempt to alter any CBRS Setting, including the URL, or else the CPE device will stop working. Warning Before considering or making any changes to these settings consult with your authorized Certified Professional Installer (CPI). Any changes will require the CPE device to be submitted to a new CBRS SAS installation and registration process. For more information on the Aurora Pro installation app and its interaction with the CBRS system, refer to the Aurora ODU Installation App (CBRS) User Guide. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 66 of 84 6.3.6.1 Install parameters This page is typically used for troubleshooting purposes. Consult with authorized Certified Professional Installer

(CPI) and the debug or troubleshooting guide prior to troubleshooting installation issues. To access the CBRS SAS screens, select the Services item from the top menu bar then open the CBRS SAS menu item. From the CBRS SAS submenu select the Install parameters item on to view the status of the installation and parameters entered by the CPI and as registered with the CBRS. Figure 66 CBRS install parameters page [truncated]

6.3.6.2 Debug parameters This page is typically used for troubleshooting purposes. Consult with authorized Certified Professional Installer

(CPI) and the debug or troubleshooting guide prior to troubleshooting installation issues. To view the current parameters, select Services and then from the CBRS SAS submenu select the Debug parameters. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 67 of 84 6.4 System 6.4.1 Log System log The System Log enables you to troubleshoot any issues you may be experiencing with the AurusPRO. To access the System Log page, click the System menu. A page containing the System Logs buttons are displayed. Figure 67 - System Log page You can download the log file to your local computer by clicking on the Download button. A .txt log file will be downloaded to your browsers Download folder. The Clear button clears the log file when logging to non-volatile memory is enabled (refer to the System log settings section). It does not clear the log/message buffer. 6.4.1.1 Log System log settings To access the System log settings page, click the System menu item then select the Log menu on the left and then select System log settings from the drop-down menu. Figure 68 - System Log Settings CFW-2832 User Guide UG01427 v1.01 23 September, 2022 Log capture level The log capture level defines the amount of detail that the system log stores. This setting also affects the Display level setting on the System log page. The system will capture and display events for the selected level and all the events at levels below it. For example, setting it to Notice will show Notice, Warning and Error events. 68 of 84 I t e m Debug Info D e f i n i t i o n Show extended system log messages with full debugging level details. Show informational messages. Notice Show normal system logging information. Warning Show warning messages. Error Show error condition messages only. Table 18 System log detail levels Volatile log Contents of Volatile memory is stored temporarily. 1 2 Specify the maximum Log buffer size (100-512 kilobytes). Click the Save button. A drawback of log data saved in volatile memory is that the log data is stored in RAM and therefore when the unit loses power, or is rebooted, the device will lose any log information stored in the RAM. Non-volatile memory is the type of memory in which data remains stored even if it is powered-off. To ensure that log information is accessible between reboots of the AurusPRO there are two options:

Click On to enable the Log to non-volatile memory option. Use a Remote Syslog Server. Non-volatile log When the AurusPRO is configured to log to non-volatile memory, the log data is stored in flash memory, making it accessible after a reboot of the device. Up to 512kb of log data will be stored before it is overwritten by new log data. Non-volatile logging can lead to Flash memory wear. This facility is intended for debugging only. 1 2 3 Click On to enable the Log to non-volatile memory option. Specify the maximum Log file size (500-5000 kilobytes). Click the Save button. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 69 of 84 Remote syslog server The AurusPRO can be configured to output log data to a remote syslog server. This is an application running on a remote computer which accepts and displays the log data. Most syslog servers can also save the log data to a file on the computer on which it is running allowing you to ensure that no log data is lost between reboots. To configure the AurusPRO to output log data to a remote syslog server:

1 Click the System menu from the top menu bar. The System log item is displayed. 2 Under the Remote syslog server section, enter the IP address or hostname of the syslog server in the IP /

Hostname [:PORT] field. Figure 69 Remote syslog server configuration You can also specify the port number after the IP or hostname by entering a semi-colon and then the port number e.g. 192.168.1.102:514. If you do not specify a port number, the AurusPRO will use the default UDP port 514. 3 Click the Save button to save the configuration. 6.4.1.2 QXDM over Ethernet For debugging, you can use QXDM over Ethernet. QXDM is a Qualcomm tool used for capture and analysis of mobile signalling data. To use QXDM over Ethernet:

1 2 Click on the Enable toggle key to set it to the On position. Enter the Server IP address. 3 Click the Save button to begin the capture and analysis of mobile signalling data. Figure 70 - QXDM over Ethernet page CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.4.2 Ping diagnostics Ping Diagnostics are used to send controlled ping packets to determine the status of the link. These are small packets of data that the AurusPRO sends to a remote address and if the connection is up, a reply is received. 70 of 84 Use Ping Diagnostics to test the status of the network connection:

Figure 71 - Ping Diagnostics page 1 2 3 4 In the Host field, enter the domain name or IP address that you want to send a ping request to for the test. In the Number of repetitions field, enter the number of times you want the AurusPRO to continue the ping requests. In the Timeout field, enter the number of milliseconds to wait before the ping request times out if there is no response. In the Data block size field, enter the number of bytes that the ping packet is made up of. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 71 of 84 5 6 7 8 In the DSCP field, enter an integer between 0 and 63 which acts as a classification code according to the Differentiated Services Code Point (DSCP) definition. In the Interface drop-down list, select the interface that the ping test is to be performed on. If no interface is selected, the default interface rmnet_data0 is used. In the Protocol drop-down list, select the IP protocol to use for the test. Click on the Request button. The PING DIAGNOSTIC RESULT section updates with the results of the ping request. 6.4.3 System configuration 6.4.3.1 Restore factory defaults Restoring factory defaults will reset the AurusPRO to its factory default configuration. You may encounter a situation where you need to restore the factory defaults on your AurusPRO, such as:

You have lost your User name and User password and are unable to login to the web configuration page. You are asked to perform a factory reset by support staff. To restore the AurusPRO to its factory default settings, please follow these steps:

1 Open a browser window and navigate to the IP address of the AurusPRO (default address is http://192.168.1.1). Login to the AurusPRO using root as the User Name and admin as the password. 2 Click the System item from the top menu bar, then System configuration on the left menu and then click the Restore default. Button. 3 Under the Restore factory defaults section, click the Restore defaults button. 4 A warning message will display. Figure 72 - Restore Factory Defaults page Figure 73 - Restore Factory Defaults Confirmation Message CFW-2832 User Guide UG01427 v1.01 23 September, 2022 72 of 84 5 6 Click OK to reboot the AurusPRO. The AurusPRO reboots with the default settings applied. 6.4.3.2 Web server settings You can configure whether the AurusPROs web server uses HTTP or HTTPS and the server port. Additionally, you can generate a web server certificate by entering data in all the fields under the Generate web server certificate section. Figure 74 - Web server settings CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.4.3.3 Administrator credentials Use this page to change the Password used to access the AurusPRO via SSH. 73 of 84 The default User Name and User Password for SSH access are as follows:

Figure 75 - Changing administrator credentials A d m i n i s t r a t o r a c c o u n t a c c e s s v i a S S H Username Password root oelinux123 Table 19 - Login details Administrator account via SSH Enter the Password in the table to into the Current password field if you have not previously created a new SSH access Password. If you have created a new SSH access Password but have forgotten it, you will have to Restore factory default settings, see section 6.4.3.1, above. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.4.3.4 Web UI credentials Use this page to change the default Password that you initially used to log in via the Web User Interface (refer to section 5.1 Log in as Administrator via Web UI on page 12). 74 of 84 The default User Name and User Password for Web UI access are as follows:

Figure 76 - Changing web interface credentials A d m i n i s t r a t o r a c c o u n t a c c e s s v i a W e b U I Username Password root admin Table 20 - Login details Administrator account via Web UI Enter the Password in the table to into the Current password field if you have not previously created a new Web UI access Password. If you have created a new Web UI access password but have forgotten it, you will have to Restore factory default settings, see section 6.4.3.1, above. 6.4.3.5 Settings backup/restore Use this page to save your current settings in a backup file and then to retrieve the backup file to restore your previous settings should this be necessary. To SAVE A COPY OF CURRENT SETTINGS:

1 2 Enter a Password for the new backup file. Enter the same password into the Confirm password field CFW-2832 User Guide UG01427 v1.01 23 September, 2022 3 Click the Save button. 75 of 84 A .zip folder will be downloaded to the download folder of your browser. We suggest that you move this to a secure folder. Figure 77 - Setting backup/restore page To RESTORE SAVED SETTINGS:

1 2 3 4 5 Click the Choose a file button and navigate to the backup file. Select the file and the word Uploaded will appear after the button Enter the Password you created when making the backup file. Click the Restore button. The following warning message will appear:

6 Click the OK button to proceed with the restoration of your previous settings. Figure 78 Confirmation of restore message CFW-2832 User Guide UG01427 v1.01 23 September, 2022 76 of 84 6.4.3.6 Runtime Configuration Runtime Configuration can be used to load a configuration file containing carrier-specific settings such as MBN changes which are not available via the web user interface. It is used for late binding of carrier configurations at the time of installation. Runtime Configuration files can only be created by Casa Systems engineers. Please speak to your Casa Systems representative for more information. To access the Runtime Configuration page, select System > System configuration > Runtime configuration To apply runtime configuration:

Figure 79 - Runtime configuration page 1 2 3 4 Select the Choose a file button and locate the configuration file. Select the file. The word Uploaded appears next to the button. Select the Apply button to install the configuration file. The device automatically reboots after successful upload of the configuration file. The following runtime configuration IDs will be read and displayed on this page. They are 15-digit configuration IDs that uniquely identify the configuration file. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.4.4 Firmware upgrade To access the Firmware upgrade page, navigate to System, then click Firmware Upgrade on the left side menu. 77 of 84 To upgrade the firmware of the AurusPRO:

Figure 80 - Firmware Upgrade page 1 2 3 4 Click the Choose a file button, then locate the firmware file on your computer. To remove all current settings select On for Reset to default config. Selecting Off for Reset to default config will save all current user defined settings and apply them using the new firmware. Click the Upgrade button. The AurusPRO performs the firmware upgrade and then reboots. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.4.5 Access control The Access Control page turns on or off access to the antenna via different protocols. You can specify certain protocols to have different settings from local or remote connections. 78 of 84 Figure 81 - Access Control page I t e m D e f i n i t i o n R e m o t e A c c e s s C o n t r o l HTTP Enable HTTPS Enable Enables/disables HTTP access to the web interface of the antenna from a remote connection. Enables/disables HTTPS access to the web interface of the antenna from a remote connection. SSH Enable Enables/disables SSH access to the antenna from a remote connection. Ping Enable Enables/disables a response to pings from a remote connection. L o c a l A c c e s s C o n t r o l HTTP Enable HTTPS Enable Enables/disables HTTP access to the web interface of the antenna from a local connection. Enables/disables HTTPS access to the web interface of the antenna from a local connection. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 79 of 84 I t e m D e f i n i t i o n SSH Enable Enables/disables SSH access to the antenna from a local connection. Table 21 - Access Control options It is not possible to disable both Local HTTP and HTTPS simultaneously via the WebUI in order to stop accidental lock out of the WebUI. Note Intentional lock out of the WebUI from local access can be performed by disabling both local HTTP and HTTPS via TR-069. 6.4.6 Reboot The Reboot option in the System section performs a soft reboot of the device. This can be useful if you have made configuration changes you want to implement. To reboot the AurusPRO:

1 2 3 4 5 Click the System menu item from the top menu bar. Click the Reboot button from the menu on the left side of the screen. The AurusPRO displays a warning that you are about to perform a reboot. If you wish to proceed, click the Reboot button. Figure 82 - Reboot message A warning popup will advise that It may take 1-2 minutes to reboot your device. Are you sure you want to continue?

6 Click OK to continue with the reboot process. Figure 83 - Reboot confirmation message CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.4.7 Field test The Field test page contains NR5G cell information which may be useful when troubleshooting signal strength issues. This screen can be found by navigating to System > Field test. 80 of 84 N R 5 G S e r v i n g C e l l I n f o r m a t i o n Figure 84 - Field test CC ID Cell ID Dl. ARFCN Ul. ARFCN Band Band Type Dl. bw. Ul. bw. Component Carrier ID. The physical cell identifier. Downlink Absolute Radio Frequency Channel Number. Uplink Absolute Radio Frequency Channel Number. The NR5G band. The type of the NR5G band, e.g. Sub6 or mmWave. Downlink bandwidth. Uplink bandwidth. Dl. max MIMO Downlink maximum Multiple Input Multiple Output. Ul. max MIMO Uplink maximum Multiple Input Multiple Output. Table 22 - NR5G Serving cell information CFW-2832 User Guide UG01427 v1.01 23 September, 2022 6.4.8 Encrypted Debug Information The Encrypted Debug Information page contains additional information which may be useful when troubleshooting an issue. To create a debug file navigate to System > Encrypted Debug Information. 81 of 84 Figure 85 - Encrypted Debug Information page 6.4.8.1 Generate Click the Generate button to create a debug file. While the generation process is taking place the browser will be unavailable and the message Please wait will be displayed. After a few minutes the generation process will end, the browser will become available and the Success Encrypted debuginfo file is generated successfully message will be displayed at the top of the page. 6.4.8.2 Download Click the Download button to download the new file into your browsers default downloads folder. The following debug file will be saved in your browsers default downloads folder: debuginfoX.tar.gz CFW-2832 User Guide UG01427 v1.01 23 September, 2022 82 of 84 Appendix A Safety and compliance RF Exposure Your device contains a transmitter and a receiver. When it is on, it receives and transmits RF energy. When you communicate with your device, the system handling your connection controls the power level at which your device transmits. This device meets the governments requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. This equipment complies with radio frequency (RF) exposure limits adopted by the Federal Communications Commission for an uncontrolled environment. This equipment should be installed and operated with minimum distance 24cm between the radiator and your body. FCC Statement This device must be professionally installed. FCC compliance Federal Communications Commission Notice (United States): Before a wireless device model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. FCC regulations This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. CFW-2832 User Guide UG01427 v1.01 23 September, 2022 83 of 84 However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Operating temperature

-40C to 55C Company details Casa Systems, Inc. 100 Old River Road, Andover, Massachusetts 01810 USA https://www.casa-systems.com/contact-us/

Product details Product: CBRS 5G Cat B Outdoor CPE Model No: CFW-2832 CFW-2832 User Guide UG01427 v1.01 23 September, 2022 84 of 84 Appendix B Configuring Radio Access Technologies This device supports the following modes of operations in various combinations LTE (3GPP Core Network Option 1) 5G Non Standalone (3GPP Core Network Option 3x) 5G Standalone (3GPP Core Network Option 2) Please refer to the following table to understand which modes of operation are possible and how to configure them. A l l o w e d R A T H o w t o C o n f i g u r e Mode LTE 5G NSA 5G SA Supported RAT Selection Menu Band Selection Menu LTE Only LTE + 5G NSA 5G NSA Only Yes No Yes Yes No Yes LTE + 5G NSA + 5G SA Yes Yes LTE + 5G SA 5G NSA + 5G SA 5G SA Only Yes No No No Yes No No No No Yes Yes Yes Yes Yes Yes No Select LTE only Select LTE Frequency Bands Select LTE + 5G NR Select LTE + NSA Frequency Bands Yes Select LTE + 5G NR Select LTE + NSA + SA Frequency Bands No No Yes Select 5G NR Select SA Frequency Bands Appendix table 1 RAT/Band Selection table Use this table in conjunction with the settings described in sections 6.2.1.3 RAT selection and 6.2.1.2 Band selection of this guide. Note 5G Standalone Mode is not supported when utilising mmWave frequency bands. CFW-2832 User Guide UG01427 v1.01 23 September, 2022

NetComm Wireless Pty Ltd Level 5, 18-20 Orion Road, Lane Cove,NSW, 2066, Australia Date: September 29, 2022 FCC Laboratory 7435 Oakland Mills Rd Columbia MD 21046 Subject: Request for Confidentiality FCC ID: XIA-CFW2832 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commissions rules (47CFR0.457, 0.459), we are requesting the Commission to withhold the following documents from public disclosure indefinitely. Schematic Diagram Block Diagram Part List Operational Description Tune-up Procedure Above mentioned documents which contain detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give a competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission s policy, in order to comply with the marketing regulations in 47 CFR 2.803 and the importation rules in 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we are requesting the Commission to withhold the following documents for 180 days after the grant of equipment authorization is issued:

External Photos Internal Photos Test Setup Photos Antenna report setup photos User Manual It is our understanding that all measurement test reports, FCC ID label format cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. 18-20 Orion Road Lane Cove, NSW 2066, Australia

+ 61 2 9424 2000 NetComm Wireless Pty Ltd ACN 002 490 486, acquired by Casa Systems Inc. Rev 1.1 Best Regards, _______________________ Pat Sinni pat.sinni@casa-systems.com Certification and Compliance Team Leader Tel: +61294242070; Fax: +61294242070 18-20 Orion Road Lane Cove, NSW 2066, Australia

+ 61 2 9424 2000 NetComm Wireless Pty Ltd ACN 002 490 486, acquired by Casa Systems Inc. Rev 1.1