all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 3 4 |
|
user manual | Users Manual | 484.55 KiB | July 29 2011 / January 25 2012 | |||
1 2 3 4 |
|
internal photos | Internal Photos | 1.24 MiB | July 29 2011 / January 25 2012 | |||
1 2 3 4 |
|
external photos | External Photos | 493.62 KiB | July 29 2011 / January 25 2012 | |||
1 2 3 4 |
|
label location | ID Label/Location Info | 144.62 KiB | July 29 2011 | |||
1 2 3 4 |
|
Class II Letter | Cover Letter(s) | 24.76 KiB | September 28 2011 | |||
1 2 3 4 |
|
LTC Request | Cover Letter(s) | 57.75 KiB | September 28 2011 | |||
1 2 3 4 |
|
MPE | RF Exposure Info | 100.35 KiB | September 28 2011 | |||
1 2 3 4 | Operational Description | Operational Description | September 28 2011 | confidential | ||||
1 2 3 4 |
|
Power of Attorney Letter | Cover Letter(s) | 29.32 KiB | September 28 2011 | |||
1 2 3 4 |
|
Test Report | Test Report | 771.26 KiB | September 28 2011 | |||
1 2 3 4 |
|
Test Setup Photos | Test Setup Photos | 76.21 KiB | September 28 2011 / March 26 2012 | |||
1 2 3 4 |
|
DoC letter | Cover Letter(s) | 24.16 KiB | July 29 2011 | |||
1 2 3 4 | block diagram | Block Diagram | July 29 2011 | confidential | ||||
1 2 3 4 |
|
co location report | Test Report | 104.34 KiB | July 29 2011 | |||
1 2 3 4 |
|
request for confidentiality | Cover Letter(s) | 58.17 KiB | July 29 2011 | |||
1 2 3 4 | schematics | Schematics | July 29 2011 | confidential |
1 2 3 4 | user manual | Users Manual | 484.55 KiB | July 29 2011 / January 25 2012 |
N900 Wireless Dual Band Gigabit Router WNDR4500 Setup Manual NETGEAR, Inc. 350 E. Plumeria Drive San Jose, CA 95134 USA November 20101 208-107xx-xx v1.0 2010 by NETGEAR, Inc. All rights reserved. Trademarks NETGEAR and the NETGEAR logo are registered trademarks, and Smart Wizard is a trademark of NETGEAR. Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. 2 Contents N900 Wireless Dual Band Gigabit Router WNDR4500 Setup Manual Getting to Know Your Wireless Router................................................................................1 Unpacking Your New Wireless Router ..............................................................................1 Hardware Features ............................................................................................................2 Front Panel ..................................................................................................................3 Back Panel ..................................................................................................................5 Router Label ................................................................................................................6 Positioning Your Wireless Router ......................................................................................6 Installing Your Wireless Router .........................................................................................7 Updating Your Router Firmware ........................................................................................8 Installing Your Wireless Router Using Smart Wizard ...........................................................................................................................9 Installing Your Wireless Router Manually (Advanced and Linux Users)........................11 Connecting Your N900 Wireless Gigabit Router .............................................................11 Verifying Your Connection ...............................................................................................14 Setting Up Your Router for Internet Access ....................................................................15 Configuring Your Wireless Network...................................................................................19 Accessing Your Router After Installation and Checking for New Firmware .....................19 Configuring Your Wireless Settings and Security Options ..............................................20 Setting Your SSID and Wireless Security Manually ..................................................20 Using Push 'N' Connect (WPS) to Configure Your Wireless Network .......................23 Testing Basic Wireless Connectivity ................................................................................24 Troubleshooting...................................................................................................................26 Basic Setup Checklist ......................................................................................................26 Checking Basic Router Functions ...................................................................................27 Troubleshooting Login Problems .....................................................................................29 Contents iii Checking the Internet Service Connection ......................................................................30 Obtaining an Internet IP Address ..............................................................................30 Troubleshooting PPPoE ............................................................................................31 Troubleshooting Internet Browsing ...........................................................................32 Troubleshooting Connectivity Using the Ping Utility ........................................................32 Testing the Path from a PC to Your Router ..............................................................32 Testing the Path from a PC to the Internet ................................................................33 Technical Specifications .....................................................................................................35 Default Configuration Settings .........................................................................................35 Restoring the Default Password and Configuration Settings ...........................................38 Related Documents .............................................................................................................39 Registration and Certifications............................................................................................40 Contents iv Installing Your Wireless Router To help you set up your router and get on the Internet quickly, the Resource CD contains a Smart Wizard. The Smart Wizard walks you through the steps required to connect your router and PC(s); configure your internet settings; configure your wireless settings; and enable wireless security for your network. When you have finished, you will be Internet ready!
If you have a Linux system, you need to use the manual installation method (see Installing Your Wireless Router Manually (Advanced and Linux Users) on page 11). You can set up your N750 wireless gigabit router using one of two methods:
Smart Wizard Setup: The Smart Wizard setup is available on your Resource CD. See Installing Your Wireless Router Using Smart Wizard on page 9 to use the Smart Wizard. This is the easiest option. The wizard guides you through the setup process. It automates many of the steps and verifies that the steps have been successfully completed. Smart Wizard requires a PC running Microsoft Windows or a Mac. Before running the Smart Wizard on a corporate PC to set up your home router, check with your companys network support staff. Corporate network settings or Virtual Private Network (VPN) client software may conflict with the default settings of a home router. If you are unsure about whether there might be a conflict, use a different computer. Manual Setup: If you cannot or prefer not to use the Smart Wizard, see Installing Your Wireless Router Manually (Advanced and Linux Users) on page 11. For example, if you are using a Linux operating system or are technically knowledgeable, select this option. If you choose to use this option and install your router manually, for best results, install and set up your router in this order:
1. Install and connect your wireless router to your network (see Connecting Your N750 Wireless Gigabit Router on page 11). 2. Set up your wireless router for Internet access (see Setting Up Your Router for Internet Access on page 15). 3. Configure your wireless network and select wireless security settings to protect your wireless network (see Configuring Your Wireless Network on page 19). Getting to Know Your Wireless Router 7 Updating Your Router Firmware NETGEAR is always improving the operability and features included with your router. To make it easy for you to receive the best, most up-to-date features of your router, NETGEAR provides a variety of methods for updating your product. The Smart Wizard installation assistant lets you check for and install updates as part of the setup activity. The router includes an update feature that lets you check for and install updates. You must be logged in to the router to use this feature (see the Reference Manual for details). These options are discussed in Installing Your Wireless Router Manually (Advanced and Linux Users) on page 11. Getting to Know Your Wireless Router 8 Installing Your Wireless Router Using Smart Wizard Prepare the following before you set up your router, making sure that:
You are using a computer with either a Mac operating system or a Windows operating system
(Windows 7, Windows Vista, Windows 2000, or Windows XP with Service Pack 2 or above). You have an Internet service connection through an Internet Service Provider (ISP). Your PC has a wired Ethernet connection (not a wireless connection). For cable modem service, that you use the computer you first used to set up your Internet service. The NETGEAR Smart Wizard takes you through the procedure to connect your router and PC(s). It then helps you to configure your wireless settings and enable wireless security for your network. The Smart Wizard guides you through the setup and configuration process by automating many of the steps. At each step in the setup process, the Smart Wizard checks to ensure that the steps you perform are successfully completed. The wizard setup process takes about 20 minutes to complete. To set up your router using the Smart Wizard:
1. To start the Smart Wizard:
For Windows users, Insert the Resource CD into your PC. The CD will automatically start and detect the language you are using on your PC. Select a different language option, if you prefer. If the CD does not automatically start, browse the CD and double-click on
. In the CDs menu, click Setup to start the Smart Wizard. For Mac users, double-click the MacWizard program. 2. When the Smart Wizard prompts you to Check for Firmware Updates, click Yes to check the NETGEAR website for new router firmware; or check No to check for updates later (see Accessing Your Router After Installation and Checking for New Firmware on page 19). Installing Your Wireless Router Using Smart Wizard 9 3. Follow the instructions and prompts to complete the installation. The Smart Wizard guides you through installing your router, connecting your router to the Internet, configuring your wireless network settings, and selecting the optimum security protection for your network. If you choose not to select a security option during installation, you can always access the routers user interface later to select a security option (see Setting Your SSID and Wireless Security Manually on page 20 or Using Push 'N' Connect (WPS) to Configure Your Wireless Network on page 23). To ensure optimum performance of your high-speed wireless router, the wireless adapter card for each computer in your network should support the same technology as your router (see the online User Manual for more information). At the close of installation:
For Windows users, the Smart Wizard places a Router_Setup.html file on your computers desktop so that you can view the router settings. It also places the Router Login For Mac users, the Smart Wizard places a Router_Setup.pdf file on your desktop. shortcut on the desktop for you to access the routers main menu. You are now connected to the Internet!
After connecting to the Internet, you can:
Log in to the router and check for new firmware. Refer to the bottom label for the default login information, or see the steps in Accessing Your Router After Installation and Checking for New Firmware on page 19. Set up additional wireless computers in your network for Internet access (see Configuring Your Wireless Settings and Security Options on page 20). For advanced features not covered in this manual, see the Reference Manual on your Resource CD. A link to the online Reference Manual also is available from the router interface. The factory default state is restored when you use the restore factory settings button. See Restoring the Default Password and Configuration Settings on page 38 for more information about this feature. Installing Your Wireless Router Using Smart Wizard 10 Installing Your Wireless Router Manually
(Advanced and Linux Users) Before installing and connecting your router manually, review the list below and make sure that you have all of the necessary information. A DSL or cable service connection to an Internet Service Provider (ISP). The configuration information your ISP gave you. Depending on how your Internet account was set up, you might need the following information to set up your N750 wireless gigabit router and access the Internet:
Host and Domain Name Domain Name Server (DNS) Addresses Your ISP should have provided you with all the information needed to connect to the Internet. If you cannot locate this information, contact your ISP. Internet Login Name and Password (frequently an email address and password) Fixed or Static IP Address If you have not already done so:
Check the package contents of your router to ensure that it is complete (see Unpacking Your New Wireless Router on page 1). Select an optimum location for your N750 wireless gigabit router after reviewing the guidelines presented in Positioning Your Wireless Router on page 6. Connecting Your N750 Wireless Gigabit Router Before you install your N750 wireless gigabit router, make sure that the Internet Protocol (TCP/IP) Property settings on your computer are set to automatically obtain an IP address using DHCP and Obtain DNS server address automatically. You can check these settings by looking at the TCP/IP Properties of your Internal Network Connections, which are accessible through the Installing Your Wireless Router Manually (Advanced and Linux Users) 11 Control Panel of your computer. If you are unsure about this, refer to the documentation for your computer or see the link to TCP/IP Addressing in Related Documents on page 39. If you are replacing an existing router, disconnect it completely from your network and set it aside before starting to install your new router. There are two steps to setting up your N750 wireless gigabit router:
1. Connect the router to the ADSL or cable modem, and connect a computer to the router. 2. Configure the router to use your Internet service. To connect your N750 wireless gigabit router:
1. Connect the N750 wireless gigabit router, the computer, and the modem. a. Turn off your computer. b. Turn off and unplug the cable or ADSL broadband modem. If your modem has a backup battery, remove it as well. c. Locate the Ethernet cable (1) that connects your computer to the modem. 1 2 Figure 5 2. Disconnect the cable from the modem (2). You will connect it to the router later. 3. Locate the Ethernet cable that came with the NETGEAR product. Securely insert that Ethernet cable into your modem and into the Internet port of the N750 wireless gigabit router (3). Installing Your Wireless Router Manually (Advanced and Linux Users) 12 3 Figure 6 4. Locate the cable you removed from the modem in step 2. Securely insert that cable (4) into a LAN port on the router such as LAN port 1. 4 Figure 7 Your network cables are connected, and you are ready to start your network. It is important that you start your network in the correct sequence. To start your network in the correct sequence. Failure to start or restart your network in the correct sequence could prevent you from accessing the Internet. Installing Your Wireless Router Manually (Advanced and Linux Users) 13 1. First, plug in and turn on the cable or DSL modem (if your modem has a backup battery, plug it back in). Wait 2 minutes. 2. Now, plug the power cord into your N750 wireless gigabit router and into a power outlet. Wait 1 minute. 3. Last, turn on your computer. It might take several minutes for your router to establish a connection with your computer and your Internet provider. For DSL customers, if software logs you in to the Internet, do not run that software. You might need to go to the Internet Explorer Tools menu, select Internet Options, and then click the Connections tab, where you can select Never dial a connection. Verifying Your Connection Verify that your router is connected correctly by checking the wireless router status lights (as illustrated in Figure 8. 1 2 3 4 5 6 7 Figure 8 Check the N750 wireless gigabit router status lights to verify the following:
Power. The Power light (1) should turn solid green. If it does not, see Checking Basic Router Functions on page 27. Internet. The Internet port light (2) should be lit. If it is not, make sure that the Ethernet cable is securely attached to the N750 wireless gigabit router Internet port and that the modem, and that the modem is powered on. Operating Mode. The 2.4 GHz N/G-Band light (3) should be on; the 5.0 GHz N-Band light
(3) should be on. Installing Your Wireless Router Manually (Advanced and Linux Users) 14 LAN. At least one LAN light (4) should be lit. Green indicates that your computer is communicating at 1 Gbps; amber indicates 10/100 Mbps. If a LAN light is not lit, check that the Ethernet cable from the computer to the router is securely attached at both ends, and that the computer is turned on. USB. The USB light (5) should be lit if a USB device is connected and ready to be used. The light will be fast blinking green when the USB device is in use. WLAN On/Off. The Wireless Local Area Network (WLAN) button (6) turns the 2.4 GHz and 5.0 GHz wireless radios on and off. WPS. The WPS button (7) shows blinking green to indicate WPS activity, when the device is in the 2 minute interval to synchronize security or there is a WPS error. Setting Up Your Router for Internet Access When configuring your wireless router manually, you must log in to your N750 wireless gigabit router to set it up initially and to make any changes to your wireless routers settings later. The factory default state is reset when you use the Restore Factory Settings button. See Restoring the Default Password and Configuration Settings on page 38 for more information. To access your router:
1. Connect to the N750 wireless gigabit router by typing http://www.routerlogin.net in the address field of your browser, and then press Enter. Figure 9 Connect to the N750 wireless gigabit router by typing any one of these three URLs in the address field of your browser, then pressing Enter:
http://www.routerlogin.net http://www.routerlogin.com http://192.168.1.1 Installing Your Wireless Router Manually (Advanced and Linux Users) 15 A login window such as the one in the following figure displays:
Figure 10 2. For security reasons, the router has its own user name and password. When prompted, enter admin for the router user name and password for the router password, both in lowercase letters. The router user name and password are not the same as any other user name or password you might use to log in to your Internet connection. A progress bar will display, checking for a new version of the firmware. If new firmware is available, click Yes, and the router will automatically upgrade itself with the latest firmware. 3. Do not try to go online, turn off the router, shut down the computer, or do anything else to the router until the router finishes restarting and the Ready light has turned solid green for several seconds!
Installing Your Wireless Router Manually (Advanced and Linux Users) 16 4. From the main menu, select Setup Wizard. The Setup Wizard screen displays. Figure 11 5. Select No to set up the connection yourself. Click Next and the Basic Settings screen will display. Enter the required information for your ISP connection in the appropriate fields. If you need assistance, follow the Basic Settings Help screens on the router interface or see the online User Manual for this N750 wireless gigabit router. If you cannot connect to the wireless router, check the Internet Protocol
(TCP/IP) properties in the Network Connections section of your Control Panel. It should be set to obtain both IP and DNS server addresses automatically. For assistance, see your computer documentation or see the links in Related Documents on page 39. 6. Click Apply to save your settings and complete your connection. You are now connected to the Internet! The N750 wireless gigabit router home page will display. To complete your router setup and to configure your wireless network, see Accessing Your Router After Installation and Checking for New Firmware on page 19 and Configuring Your Wireless Settings and Security Options on page 20. Installing Your Wireless Router Manually (Advanced and Linux Users) 17 If you do not connect successfully:
Review your settings and make sure that you have selected the correct options and typed everything correctly. Contact your ISP to verify that you have the correct configuration information. Read Troubleshooting on page 26. If problems persist, register your NETGEAR product and contact NETGEAR Technical Support. Installing Your Wireless Router Manually (Advanced and Linux Users) 18 Configuring Your Wireless Network After installing your router, you must log into the router to complete your wireless setup. When you log in to the browser, you will be prompted to check for firmware updates from the NETGEAR update server. Accessing Your Router After Installation and Checking for New Firmware The Smart Wizard only appears when you run the CD. If you want to change the settings after installing and configuring your router, you can click the desktop shortcuta pre-configured shortcut placed on your desktop by the Smart Wizard at installationto open the router management interface.1 You can also change your settings, or configure your wireless and security settings, by opening a browser window and logging in to the router. You will also be prompted to check for new router firmware for the router. To log in to the router after installation:
1. Open a browser window and type http://www.routerlogin.net in the address field of your browser. Press Enter. You can enter either of these addresses to connect to your wireless router:
http://www.routerlogin.net or http://www.routerlogin.com. 2. When prompted, enter the Password (admin is the default router User Name and password is the default router Password), both in lowercase letters. If you changed the Password from the defaults, then enter your new Password. The router User Name and Password are unique to the router and are not the same as any other User Name or Password you may use to log in to your Internet connection. 1. The shortcut icon is installed on your desktop only when using the Smart Wizard installation method. Configuring Your Wireless Network 19 Configuring Your Wireless Settings and Security Options The wireless network settings of the router must match the wireless network settings of any wireless devices that connect wirelessly to the router (such as wireless adapter cards and wireless computers). For a wireless connection, the router and each wireless computer must use the same SSID, also called the wireless network name, and the same wireless security. NETGEAR strongly recommends that you use wireless security. Indoors, computers can connect over wireless networks at a range of several hundred feet. This can allow others outside of your immediate area to access your network. The Wireless Settings screen lets you set your wireless network connections and the wireless security option for your network and router. To configure the wireless network, you can either manually specify your network name (SSID) and your wireless security settings (see Setting Your SSID and Wireless Security Manually on page 20) or, if the clients in your network are WPS capable, you can use Wi-Fi Protected Setup (WPS) to automatically set the SSID and implement WPA/WPA2 security on both the router and the client device (see Using Push 'N'
Connect (WPS) to Configure Your Wireless Network on page 23). If you configure the router from a wireless computer and you change the routers SSID, channel, or security settings, you will lose your wireless connection when you click Apply. You must then change your computers wireless settings to match the routers new settings. To avoid this situation, you can use a computer that is connected to the router with an Ethernet cable. For a complete overview of all the security configurations that can be implemented on this router, see the online User Manual. A link to the User Manual is on the Resource CD. Setting Your SSID and Wireless Security Manually To specify the wireless settings, you must know the following:
Name (11N 2.4 GHz SSID). The default is NETGEAR. Name (11N 5 GHz SSID). The default is NETGEAR-5G. Configuring Your Wireless Network 20 The wireless mode (802.11n) that each wireless adapter supports. The default is Up to 145Mbps at 2.4 GHz and 450Mbps at 5 GHz. Wireless security option. NETGEAR strongly recommends that you use wireless security. To successfully implement wireless security, check each wireless adapter to determine which wireless security option it supports. To set up basic wireless connectivity on your router:
1. Log in to the N750 wireless gigabit router at http://www.routerlogin.net, with the default user name of admin and default password of password, or using whatever LAN address and password you have set up. 2. Select Wireless Settings under Setup in the main menu to display the Wireless Settings screen. 3. Select your region. In the United States, the default region cannot be changed. For the rest of the world, the default region is Europe. 4. Set up the 2.4 GHz wireless network:
a. Enter the SSID name. The default is NETGEAR. The SSID of any wireless adapters must match the SSID you configure in the N750 wireless gigabit router. If they do not match, you will not get a wireless connection. b. Select the operating channel for the wireless mode. The default is Auto. When Auto is selected, the router finds the best operating channel available. If you notice interference from nearby devices, you can select a different channel. Channels 1, 6, and 11 will not interfere with each other. c. Leave the wireless mode set to the default setting of Up to 145Mbps for 2.4GHz. 5. Select security options for the 2.4GHz wireless network. The wireless Security Options are set to None by default. NETGEAR strongly recommends that you use wireless security. You can select a different Security Option and a different passphrase for each wireless network. For the highest performance of the 2.4GHz wireless network and the most secure encryption, NETGEAR recommends that you use WPA2-PSK as your security option. 6. Set up the 5GHz wireless network:
Configuring Your Wireless Network 21 a. Enter the SSID name. The default is NETGEAR-5G. The SSID of any wireless adapters must match the SSID you configure in the N750 wireless gigabit router. If they do not match, you will not get a wireless connection. b. Select the operating channel for the wireless mode. The default is 153 for North America, and 44 for most other countries. If there is an Auto option in the channel list and you select it, the router will find the best operating channel available. If you notice interference from nearby devices, you can select a different channel. c. Leave the wireless mode set to the default setting of Up to 450Mbps for 5GHz. 7. Select security options for the 5 GHz wireless network. The wireless Security Options are set to None by default. NETGEAR strongly recommends that you use wireless security. You can select a different Security Option and a different passphrase for each wireless network. For the highest performance of the 5 GHz wireless network and the most secure encryption, NETGEAR recommends that you use WPA2-PSK as your security option. 8. Click Apply to save your changes. If you are configuring the router from a wireless computer and you change the routers SSID, channel, or security settings, you will lose your wireless connection when you click Apply. You must then change the wireless settings of your computer to match the routers new settings. To set up your computers for wireless connectivity:
1. Program the wireless settings of each computer or wireless adapter to have the same SSID
(wireless network name) as the router. 2. Check that the wireless adapter on each computer can support the mode and security option that you selected. (If you have a question, see the online User Manual or review the settings you selected in Configuring Your Wireless Settings and Security Options on page 20). 3. Check that the security settings on each wireless device match the security settings of the router. For example, if you selected a security option requiring a passphrase, then the same passphrase must be used for each wireless computer. Configuring Your Wireless Network 22 4. Check that each wireless computer has a wireless link and is able to obtain an IP address by DHCP from the router. For a Windows PC, go to the Control Panel and select Network Connections. Check the Wireless Connections Properties and ensure that TCP/IP Properties are set to Obtain an IP address automatically. To access the Internet from any computer connected to your N750 wireless gigabit router, launch a browser such as Microsoft Internet Explorer or Mozilla Firefox. Using Push 'N' Connect (WPS) to Configure Your Wireless Network If your wireless clients support Wi-Fi Protected Setup (WPS), you can use this feature to configure the routers SSID and security settings and, at the same time, connect the wireless client securely and easily to the router. Look for the configures the SSID and wireless security settings for the router (if the router is in its default state) and broadcasts these settings to the wireless client. symbol on your client device.1 WPS automatically NETGEARs Push 'N' Connect feature is based on the Wi-Fi Protected Setup
(WPS) standard. All other Wi-Fi-certified and WPS-capable products should be compatible with NETGEAR products that implement Push 'N' Connect. If the router has already been configured manually or by using the Smart Wizard, and any of these security options have been enabled (WEP with auto authentication, WPS-PSK, WPA2-PSK, or no security), a wireless client can be added to your network quickly and simply by using Push 'N'
Connect. In this case, the existing wireless settings are broadcast to the WPS-capable client. (For more information on setting up a mixed network, see the online User Manual. A link to the User Manual is on the Resource CD.) The following instructions assume that you are configuring WPS on the router for the first time and connecting a WPS-capable device such as a wireless computer or wireless adapter. To connect a device using WPS:
1. Open the networking utility of the device you want to connect to that supports WPS. 2. Push the N750 wireless gigabit routers WPS button, then release. The WPS LED will start to blink. 1. For a list of other Wi-Fi-certified products available from NETGEAR, go to http://www.wi-fi.org. Configuring Your Wireless Network 23 3. While the WPS LED is blinking, you have 2 minutes to enable WPS on the device you are connecting to. The blinking ceases when one of these two conditions occurs:
WPS has enabled security between the router and the other device.The router has generated an SSID, implemented WPA/WPA2 wireless security (including a PSK security password) on the router and has sent this configuration to the wireless client. If you do not establish a connection using WPS during this 2-minute interval, your router security and SSID (wireless network name) will be restored to the default settings (router security will be set to None). The WPS LED will stop blinking or turn off, depending on whether the wireless device has connected successfully. 4. Note the new SSID and WPA/WPA2 password for the wireless network. To access the Internet from any computer connected to your N750 wireless gigabit router, launch a browser such as Microsoft Internet Explorer or Firefox. If you are planning a mixed network of WPS capable devices and non-WPS capable devices, NETGEAR suggests that you set up your wireless network and security settings manually first, and use WPS only for adding additional WPS capable devices. For more information about setting up your wireless network and configuring your wireless security settings, see the User Manual. A link to the online User Manual is on your Resource CD. Testing Basic Wireless Connectivity Once you have established basic wireless connectivity and enabled security settings appropriate to your needs, you can test connectivity between devices connected to your router. To test basic wireless connectivity:
1. Log in to the N750 wireless gigabit router at http://www.routerlogin.net, using the default user name of admin and default password of password, or using whatever LAN address and password you have set up. 2. Select Wireless Settings from the main menu of the N750 wireless gigabit router. Configuring Your Wireless Network 24 3. Note your SSID name. If you used WPS to establish a connection with other devices, the SSID will now be a randomly selected name. The SSID of any wireless adapters or wireless devices connected to your router must match the SSID you configured in the N750 wireless gigabit router. If they do not match, you will not get a wireless connection. 4. Make sure that you have selected the region in which the wireless router will operate. 5. Check the Wireless mode. The default is Up to 450Mbps at 5GHz & 145Mbps at 2.4GHz. If you are experiencing interference, try selecting one of the other available settings (see Configuring Your Wireless Settings and Security Options on page 20). 6. Check your wireless security. If you used WPS to enable wireless security, your security will be set to WPA/WPA2 with a randomly-selected PSK security password. 7. Click Apply to save any changes. If you are configuring the router from a wireless computer and you change the routers SSID, channel, or security settings, you will lose your wireless connection when you click Apply. You must then change the wireless settings of your computer to match the routers new settings. 8. Configure and test your computers for wireless connectivity. Program the wireless adapter of your computers to have the same wireless network name
(SSID) as the N750 wireless gigabit router and the same wireless security as your N750 wireless gigabit router. Check that they have a wireless link and are able to obtain an IP address by DHCP from the router. Your N750 wireless gigabit router is now configured to provide Internet access for your network. Your N750 wireless gigabit router automatically connects to the Internet when one of your computers requires access. It is not necessary to run a dialer or login application such as Dial-Up Networking or Enternet to connect, log in, or disconnect. These functions are performed automatically by the N750 wireless gigabit router as needed. To access the Internet from any computer connected to your N750 wireless gigabit router, launch a browser such as Microsoft Internet Explorer or Mozilla Firefox. For more information on setting up your wireless network and configuring your wireless security settings, see the User Manual. A link to the online User Manual is on your Resource CD. Configuring Your Wireless Network 25 Troubleshooting This chapter gives information about troubleshooting your N750 wireless gigabit router. You can find help with the following problems:
Basic Setup Checklist on page 26 Checking Basic Router Functions on page 27 Troubleshooting Login Problems on page 29 Checking the Internet Service Connection on page 30 Testing the Path from a PC to Your Router on page 32 Testing the Path from a PC to the Internet on page 33 Basic Setup Checklist The following items are the most common errors made when initially setting up a router. Carefully review the checklist to make sure that you have followed the recommended procedures. Be sure to always start your network in this sequence:
1. Turn off and unplug the modem from its power outlet, and turn off the N750 wireless gigabit router and computer. 2. Turn on the modem, and wait 2 minutes. 3. Turn on the N750 wireless gigabit router, and wait 1 minute. 4. Turn on the computer. Make sure that the Ethernet cables are securely plugged in:
1. Verify that the Internet status light on the N750 wireless gigabit router is lit if the Ethernet cable to the N750 wireless gigabit router from the modem is plugged in securely and the modem and N750 wireless gigabit router are both turned on (see Front Panel on page 3). 2. Verify that for each powered-on computer connected to the N750 wireless gigabit router with a securely plugged in Ethernet cable, the corresponding N750 wireless gigabit router LAN port status light is lit (see Front Panel on page 3). The label on the bottom of the N750 wireless gigabit router identifies the number of each LAN port (see Router Label on page 6). Troubleshooting 26 Make sure that the network settings of the computer are correct:
1. Verify that your LAN-connected computers are configured to obtain an IP address automatically through DHCP. For help with this, see the documentation for your computer or Related Documents on page 39. 2. Verify whether the MAC address is needed. Some cable modem services require you to use the MAC address of the computer registered on the account. If this is the case, in the Router MAC Address section of the Basic Settings screen, select Use this Computers MAC Address. To save your settings, click Apply. Restart the network in the correct sequence. Check the router status lights to verify correct router operation:
If the Power light does not turn solid green within 2 minutes after you turn the router on, reset the router according to the instructions in Restoring the Default Password and Configuration Settings on page 38. Checking Basic Router Functions After you turn on power to the router, check that the following sequence of events has occurred:
1. When power is first applied, verify that the Power light is on and that it is solid amber while the router boots up (see Front Panel on page 3 for an illustration). 2. Verify that the Power light turns amber within a few seconds, indicating that the self-test procedure is running. 3. After approximately 90 seconds, verify that:
a. The color of the Power light changes to green. b. The LAN port lights are lit for any local ports that are connected. If a ports light is lit, a link has been established to the connected device. If a LAN port is connected to a 1 Gbps device, verify that the ports light is green. If the port is 10/100 Mbps, the light will be amber. c. The Internet port is connected and its light is lit. 4. Verify that the WPS button light on the front panel is blinking when you push it. Troubleshooting 27 If the correct behavior does not occur, check for a remedy from the following table. Table 3. Troubleshooting the routers LED behavior LED Behavior Power light is off. Recommended Action See Connecting Your N750 Wireless Gigabit Router on page 11), check the following:
Make sure that the power cord is properly connected to your router and that the power adapter is properly connected to a functioning power outlet. Check that you are using the power adapter supplied by NETGEAR for this product. If the error persists, you have a hardware problem and should contact technical support. Power light stays amber. When the router is turned on, the Power light turns amber for about 90 seconds and then turns green. If the light does not turn green, the router has a problem. If the Power light is still amber 2 minutes after turning on power to the router:
1. Turn the power off and back on to see if the router recovers. 2. Clear the routers configuration to factory defaults. This will set the routers IP address to 192.168.1.1. This procedure is explained in Restoring the Default Password and Configuration Settings on page 38. Power light blinks green continuously. If the error persists, you might have a hardware problem and should contact technical support. The router firmware is corrupted. To restore your firmware:
1. Make sure that your PC is connected to your router and the router is 2. powered on. Insert the Resource CD that came with your router into your PC. The CD automatically starts and detects the language you are using on your PC. Select a different language option, if you prefer. If the CD does not automatically start, browse the CD and double-click on
. 3. Click Supporting Software, then Netgear Firmware Recovery Utility, and follow the prompts for the recovery process. 4. After firmware recovery is complete, follow the prompts to restore your configuration Troubleshooting 28 Troubleshooting the routers LED behavior (continued) Table 3. Internet light stays amber. When the router is turned on, the Internet light turns amber for about 70 seconds and then turns green. If the light does not turn green, the router has a problem. If the Internet light is still amber 2 minutes after turning on power to the router:
1. The Internet is not accessible. Confirm that you have the correct internet setting. 2. Clear the routers configuration to factory defaults. This will set the routers IP address to 192.168.1.1. This procedure is explained in Restoring the Default Password and Configuration Settings on page 38. 3. Turn the power off and back on to see if the router recovers. If either the LAN or Internet lights do not light when the Ethernet connection is made, check the following:
1. Make sure that the Ethernet cable connections are secure at the router and at the computer. 2. Make sure that power is turned on to the connected computer. 3. Be sure you are using Ethernet cables like the cable that was supplied with the N750 wireless gigabit router. See Connecting Your N750 Wireless Gigabit Router on page 11 for instructions. Internet or LAN port lights are off. For more information on WPS functionality and advanced features, see the online Reference Manual. Troubleshooting Login Problems If you are unable to log in to the N750 wireless gigabit router, check the following:
If you are using an Ethernet-connected computer, check the Ethernet connection between the computer and the router as described in the previous section. Make sure that you are using the correct login information. The factory default login name is admin, and the password is password. Make sure that Caps Lock is off when you enter this information. Typically, your computers address should be in the range of 192.168.1.2 to 192.168.1.254. Refer to your computers documentation for help with finding your computers IP address. If your computers IP address is 169.254.x.x, verify that you have a good connection from the computer to the router, and then restart your computer. Troubleshooting 29 To ping the wireless router:
1. From the Windows toolbar, click Start and select Run. 2. In the field provided, type Ping followed by the address of the router, as in this example:
ping www.routerlogin.net or ping 192.168.1.1 3. Click OK. You should see a message like this one:
Pinging 192.168.1.1 with 32 bytes of data If the path is working, you see this message:
Reply from 192.168.1.1: bytes=32 time=NN ms TTL=xxx If the path is not working, you see this message:
Request timed out If the path is not functioning correctly, you could have one of the following problems:
Wrong physical connections Make sure that the LAN port light is on. If the light is off, follow the instructions in Front Panel on page 3. Check that the corresponding lights are on for your computers network interface card. Wrong network configuration Verify that the Ethernet card driver software and TCP/IP software are both installed and configured on your computer. Verify that the IP address for your router and your computer are correct and that the addresses on both begin with 255.255.255.0. Testing the Path from a PC to the Internet After verifying that the path between your computer and the N750 wireless gigabit router works correctly, test the path from your PC to the Internet. From the Windows Start > Run... menu, type:
PING -n 10 <IP address>
where <IP address> is the IP address of a remote device such as your ISPs DNS server. Troubleshooting 33 Related Documents This table provides links to reference documents that you can use to gain a more complete understanding of the technologies used in your NETGEAR product. Table 5. Link Document TCP/IP Networking Basics Preparing Your Network http://documentation.netgear.com/reference/enu/wsdhcp/index.htm http://documentation.netgear.com/reference/enu/glossary/index.htm Glossary http://documentation.netgear.com/reference/enu/tcpip/index.htm Related Documents 39 Registration and Certifications Product Registration, Support, and Documentation Register your product at http://www.NETGEAR.com/register. You must register before you can use our telephone support service. Product updates and Web support are always available by going to http://www.netgear.com/support. Setup documentation is available on the CD, on the support website, and on the documentation website. When the N750 wireless gigabit router is connected to the Internet, click the KnowledgeBase link to view support information, or click the Documentation link to view the online Reference Manual for this N750 wireless gigabit router. Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. 40 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device is going to be operated in 5.15~5.25GHz frequency range, it is restricted in indoor environment only. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 41 IC Statement This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p) is not more than that permitted for successful communication. The device could automatically discontinue transmission in case of absence of information to transmit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology. The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-channel mobile satellite systems;
IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IC Dclaration Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne peut pas provoquer d'interfrences et (2) cet appareil doit accepter toute interfrence, y compris les interfrences qui peuvent causer un mauvais fonctionnement du dispositif. Cet appareil numrique de la classe B conforme la norme NMB-003 du Canada. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. Le dispositif pourrait automatiquement cesser d'mettre en cas d'absence d'informations transmettre, ou une dfaillance oprationnelle. Notez que ce n'est pas l'intention d'interdire la transmission des informations de contrle ou de signalisation ou l'utilisation de codes rptitifs lorsque requis par la technologie. les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
Cet quipement est conforme l'exposition aux rayonnements IC RSS-102 des limites dfinies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre le radiateur et votre corps.
1 2 3 4 | internal photos | Internal Photos | 1.24 MiB | July 29 2011 / January 25 2012 |
Photographs of EUT SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A1 OF A9 ISSUED DATE
: Jul. 25, 2011 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A2 OF A9 ISSUED DATE
: Jul. 25, 2011 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A3 OF A9 ISSUED DATE
: Jul. 25, 2011 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A4 OF A9 ISSUED DATE
: Jul. 25, 2011 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A5 OF A9 ISSUED DATE
: Jul. 25, 2011 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A6 OF A9 ISSUED DATE
: Jul. 25, 2011 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A7 OF A9 ISSUED DATE
: Jul. 25, 2011 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A8 OF A9 ISSUED DATE
: Jul. 25, 2011 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A9 OF A9 ISSUED DATE
: Jul. 25, 2011
1 2 3 4 | external photos | External Photos | 493.62 KiB | July 29 2011 / January 25 2012 |
Photographs of EUT SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A1 OF A6 ISSUED DATE
: Jul. 25, 2011 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A2 OF A6 ISSUED DATE
: Jul. 25, 2011 Adapter 1 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A3 OF A6 ISSUED DATE
: Jul. 25, 2011 Adapter 2 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A4 OF A6 ISSUED DATE
: Jul. 25, 2011 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A5 OF A6 ISSUED DATE
: Jul. 25, 2011 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 PAGE NUMBER : A6 OF A6 ISSUED DATE
: Jul. 25, 2011
1 2 3 4 | label location | ID Label/Location Info | 144.62 KiB | July 29 2011 |
The label information will be printed on the housing, Label size: 110mm * 450mm NETGEAR N900 Wireless Dual Band Gigabit Router Modi
1 2 3 4 | Class II Letter | Cover Letter(s) | 24.76 KiB | September 28 2011 |
NETGEAR, Inc. 350 East Plumeria Drive, San Jose, California 95134-1911, USA Tel: +1 408 907 8000 Fax: +1 408 907 8097 Class II Change Letter Date: 2011/9/26 FEDERAL COMMUNICATIONS COMMISSION Authorization and Evaluation Division 7435 Oaklamd Mills Road Columbia, MD 21046 U.S.A. To whom it may concern, Request for Class II Permissive Change FCC ID: PY311200162 Grant Date: 07/29/2011 Pursuant to CFR 2.1043, NETGEAR, Inc. hereby requests a Class II Permissive Change. The model name shall be same as before. Modification:
This product is an extension of original report under Sporton project number: 171226 The operating test configuration of EUT for 5GHz Band was changed from 3TX/3RX to 1TX/1RX, and it was controlled by Firmware under control of the Grantee and endusers have no possibility to perform these changes by themselves. There is no change in both hardware and existing RF relevant portion. Sincerely, Applicants company name
: NETGEAR, Inc. Applicants company address : 350 East Plumeria Drive, San Jose, California 95134-1911, USA Signature
:
_____________________________ Job Title and Dept.
: Mark Gandler / Compliance Manager
: mark.gandler@netgear.com
: +1 408 907 8000 E-Mail Tel. Page No.
: 6
1 2 3 4 | LTC Request | Cover Letter(s) | 57.75 KiB | September 28 2011 |
NETGEAR, Inc. 350 East Plumeria Drive, San Jose, California 95134-1911, USA Tel: +1 408 907 8000 Fax: +1 408 907 8097 Date: 2011/9/26 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Confidentiality Request for FCC IDPY311200162 Gentlemen:
The form 731 and application have been electronically submitted and any attachments will be up loaded to your web site to be used in obtaining a grant of certification. Short-term Pursuant to DA 04-1705 of the Commissions pubic notice, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:
1. Permanent NETGEAR, Inc. requests that the material in the following files be withheld from public disclosure in accordance with Section 0.459 of the Commissions Rules, 47 C.F.R. 0.459, following grant of the application. 1. Operational Description Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. Test Setup photos Sincerely, Applicants company name
: NETGEAR, Inc. Applicants company address : 350 East Plumeria Drive, San Jose, California 95134-1911, USA Signature
:
_____________________________ Job Title and Dept.
: Mark Gandler / Compliance Manager E-Mail Tel.
: mark.gandler@netgear.com
: +1 408 907 8000 Page No.
: 8
1 2 3 4 | MPE | RF Exposure Info | 100.35 KiB | September 28 2011 |
Report No.: FR171226-02 Appendix B. Maximum Permissible Exposure FCC ID: PY311200162 Page No.
: B1 of B3 1. Maximum Permissible Exposure 1.1. Applicable Standard Report No.: FR171226-02 Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 0.25 m normally can be maintained between the user and the device.
(A) Limits for Occupational / Controlled Exposure Frequency Range
(MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S)
(mW/ cm) Averaging Time
|E|,|H| or S
(minutes) 0.3-3.0 3.0-30 30-300 300-1500 1500-100,000 614 1842 / f 61.4 1.63 4.89 / f 0.163
(100)*
(900 / f)*
1.0 F/300 5 6 6 6 6 6
(B) Limits for General Population / Uncontrolled Exposure Frequency Range
(MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S)
(mW/ cm) Averaging Time
|E|,|H| or S
(minutes) 0.3-1.34 1.34-30 30-300 300-1500 1500-100,000 614 824/f 27.5 1.63 2.19/f 0.073
(100)*
(180/f)*
0.2 F/1500 1.0 30 30 30 30 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 1.2. MPE Calculation Method E (V/m) GP 30 d Power Density: Pd (W/m) 2E 377 E Electric field (V/m) P Peak RF output power (W) G EUT Antenna numeric gain (numeric) d Separation distance between radiator and human body (m) The formula can be changed to Pd 30 377 d GP 2 From the peak EUT RF output power, the minimum mobile separation distance, d=0.15m, as well as the gain of the used antenna, the RF power density can be obtained. FCC ID: PY311200162 Page No.
: B2 of B3 1.3. Calculated Result and Limit For 5GHz UNII Band: (15.407) Antenna Type : Printed Antenna Max Conducted Power for IEEE 802.11n MCS0 20MHz: 16.83 dBm Antenna Gain
(dBi) Antenna Gain
(numeric) 4.03 2.5293 Average Average Power Density Output Power Output Power
(dBm) 16.8300
(mW) 48.1948
(S)
(mW/cm) 0.024263 For 5GHz ISM Band: (15.247) Antenna Type : Printed Antenna Max Conducted Power for IEEE 802.11n MCS0 20MHz: 27.95 dBm Directional Antenna Gain
(dBi) 4.03 Antenna Gain
(numeric) 2.5293 Average Average Power Density Output Power Output Power
(dBm) 27.9500
(mW) 623.7348
(S)
(mW/cm) 0.314015 Report No.: FR171226-02 Limit of Power Density (S)
(mW/cm) Test Result 1 Complies Limit of Power Density (S)
(mW/cm) Test Result 1 Complies FCC ID: PY311200162 Page No.
: B3 of B3
1 2 3 4 | Power of Attorney Letter | Cover Letter(s) | 29.32 KiB | September 28 2011 |
NETGEAR, Inc. 350 East Plumeria Drive, San Jose, California 95134-1911, USA Tel: +1 408 907 8000 Fax: +1 408 907 8097 Power of Attorney Date: 2011/9/21 Dear Sir, I hereby have entrusted the following person to be a proxy regarding application for Type Certification. Sporton International Inc. Address Name Job Title e-mail
: No.8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C.
: Leo Huang
: Manager
: Leohuang@sporton.com.tw I am therefore responsible for the contents of the application. Brand name and model type of the specified radio equipment: NETGEAR / WNDR4500 FCC ID: PY311200162 Product name: N900 Wireless Dual Band Gigabit Router FCC Grantee contact person information. Applicants company name
: NETGEAR, Inc. Applicants company address : 350 East Plumeria Drive, San Jose, California 95134-1911, USA Signature
:
_____________________________ Job Title and Dept.
: Mark Gandler / Compliance Manager
: mark.gandler@netgear.com
: +1 408 907 8000 E-Mail Tel. Page No.
: 2
1 2 3 4 | Test Report | Test Report | 771.26 KiB | September 28 2011 |
SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw FCC RADIO TEST REPORT Applicants company NETGEAR, Inc. Applicant Address 350 East Plumeria Drive, San Jose, California 95134-1911 FCC ID PY311200162 Manufacturers company Ambit Microsystems (Shanghai) Ltd. Manufacturer Address No. 1925, Nanle Road, Songjiang Export Processing Zone, Shanghai, China Product Name Brand Name Model Name Test Rule Part(s) Test Freq. Range Received Date Final Test Date Submission Type Class II Change N900 Wireless Dual Band Gigabit Router NETGEAR WNDR4500 47 CFR FCC Part 15 Subpart C 15.247 5725 ~ 5850MHz Jul. 05, 2011 Aug. 19, 2011 Class II Change Please refer to section 3.7 Statement Test result included is only for the IEEE 802.11n and IEEE 802.11a (5725 ~ 5850MHz) of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.10-2009 and 47 CFR FCC Part 15 Subpart C. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Report Format Version: 01 Report No.: FR171226-02AB Table of Contents 1. CERTIFICATE OF COMPLIANCE ......................................................................................................................... 1 2. SUMMARY OF THE TEST RESULT .......................................................................................................................... 2 3. GENERAL INFORMATION .................................................................................................................................. 3 Product Details....................................................................................................................................................................................3 3.1. Accessories.........................................................................................................................................................................................5 3.2. Table for Filed Antenna.......................................................................................................................................................................5 3.3. Table for Carrier Frequencies .............................................................................................................................................................6 3.4. Table for Test Modes...........................................................................................................................................................................6 3.5. Table for Testing Locations..................................................................................................................................................................6 3.6. Table for Class II Change ...................................................................................................................................................................7 3.7. Table for Supporting Units ...................................................................................................................................................................7 3.8. 3.9. Table for Parameters of Test Software Setting .....................................................................................................................................8 3.10. Test Configurations .............................................................................................................................................................................9 4. TEST RESULT ................................................................................................................................................... 10 4.1. Maximum Conducted Output Power Measurement.........................................................................................................................10 Power Spectral Density Measurement ..............................................................................................................................................15 4.2. 6dB Spectrum Bandwidth Measurement ..........................................................................................................................................20 4.3. Radiated Emissions Measurement ....................................................................................................................................................25 4.4. 4.5. Band Edge Emissions Measurement .................................................................................................................................................36 Antenna Requirements .....................................................................................................................................................................40 4.6. 5. LIST OF MEASURING EQUIPMENTS ................................................................................................................... 41 6. TEST LOCATION.............................................................................................................................................. 43 7. TAF CERTIFICATE OF ACCREDITATION ............................................................................................................. 44 APPENDIX A. TEST PHOTOS ........................................................................................................................ A1 ~ A2 APPENDIX B. MAXIMUM PERMISSIBLE EXPOSURE .......................................................................................... B1 ~ B3 Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: i of ii
:Sep. 23, 2011 Report No.: FR171226-02AB History of This Test Report REPORT NO. VERSION DESCRIPTION ISSUED DATE FR171226-02AB Rev. 01 Initial issue of report Sep. 23, 2011 47 CFR FCC Part 15 Subpart C o 6 2437 MHz Further, this requirement does not apply to intentional radiators that must be professionally installed. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: ii of ii
:Sep. 23, 2011 2. SUMMARY OF THE TEST RESULT Report No.: FR171226-02AB Part Rule Section Description of Test Result Under Limit Applied Standard: 47 CFR FCC Part 15 Subpart C 4.1 4.2 4.3 4.4 4.5 4.6 15.247(b)(3) Maximum Conducted Output Power 15.247(e) Power Spectral Density 15.247(a)(2) 6dB Spectrum Bandwidth 15.247(d) 15.247(d) 15.203 Radiated Emissions Band Edge Emissions Antenna Requirements Complies Complies Complies Complies Complies Complies 2.05 dB 3.59 dB
-
7.18 dB
-
-
Test Items Uncertainty Remark AC Power Line Conducted Emissions Maximum Conducted Output Power Power Spectral Density 6dB Spectrum Bandwidth Radiated Emissions (9kHz~30MHz) Radiated Emissions (30MHz~1000MHz) Radiated / Band Edge Emissions (1GHz~18GHz) Radiated Emissions (18GHz~40GHz) Temperature Humidity DC / AC Power Source 2.3dB 0.8dB 0.5dB 8.510-8 0.8dB 1.9dB 1.9dB 1.9dB 0.7 3.2%
1.4%
Confidence levels of 95%
Confidence levels of 95%
Confidence levels of 95%
Confidence levels of 95%
Confidence levels of 95%
Confidence levels of 95%
Confidence levels of 95%
Confidence levels of 95%
Confidence levels of 95%
Confidence levels of 95%
Confidence levels of 95%
Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 2 of 44
: Sep. 23, 2011 3. GENERAL INFORMATION 3.1. Product Details Report No.: FR171226-02AB Items Description IEEE 802.11n Product Type Radio Type Power Type Modulation Data Modulation Data Rate (Mbps) Frequency Range Channel Number WLAN (1TX, 1RX) Intentional Transceiver From power Adapter see the below table for IEEE 802.11n OFDM (BPSK / QPSK / 16QAM / 64QAM) see the below table for IEEE 802.11n 5725 ~ 5850MHz 5 for 20MHz bandwidth ; 2 for 40MHz bandwidth Channel Band Width (99%) MCS0 (20MHz): 16.84 MHz ; MCS0 (40MHz): 36.32 MHz Maximum Conducted Output Power MCS0 (20MHz): 27.95 dBm ; MCS0 (40MHz): 27.44 dBm Carrier Frequencies Antenna 802.11a Please refer to section 3.4 Please refer to section 3.3 Items Description Product Type Radio Type Power Type Modulation Data Modulation Data Rate (Mbps) Frequency Range Channel Number WLAN (1TX, 1RX) Intentional Transceiver From power Adapter OFDM for IEEE 802.11a OFDM (BPSK / QPSK / 16QAM / 64QAM) OFDM (6/9/12/18/24/36/48/54) 5725 ~ 5850MHz 5 Channel Band Width (99%) 16.76 MHz Maximum Conducted Output Power 27.86 dBm Carrier Frequencies Antenna Please refer to section 3.4 Please refer to section 3.3 Note: The test configuration, test mode and test software used in this test report are designated by the applicant. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 3 of 44
: Sep. 23, 2011 Antenna & Band width Antenna Band width Mode IEEE 802.11a IEEE 802.11n IEEE 802.11n spec Report No.: FR171226-02AB Single (TX) 20 MHz V V 40 MHz X V MCS Index 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Nss Modulation R NBPSC NCBPS NDBPS Datarate(Mbps) 800nsGI 400nsGI 20MHz 40MHz 20MHz 40MHz 20MHz 40MHz 20MHz 40MHz 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 BPSK QPSK QPSK 16-QAM 16-QAM 64-QAM 64-QAM 64-QAM BPSK QPSK QPSK 16-QAM 16-QAM 64-QAM 64-QAM 64-QAM 1/2 1/2 3/4 1/2 3/4 2/3 3/4 5/6 1/2 1/2 3/4 1/2 3/4 2/3 3/4 5/6 1 2 2 4 4 6 6 6 1 2 2 4 4 6 6 6 52 104 104 208 208 312 312 312 104 208 208 416 416 624 624 624 108 216 216 432 432 648 648 648 216 432 432 864 864 1296 1296 1296 26 52 78 104 156 208 234 260 52 104 156 208 312 416 468 520 54 108 162 216 324 432 486 540 108 216 324 432 648 6.5 13.5 7.200 13.0 19.5 26.0 39.0 27.0 14.400 40.5 21.700 54.0 28.900 81.0 43.300 15 30 45 60 90 52.0 108.0 57.800 120 58.5 121.5 65.000 135 65.0 135.0 72.200 150 13.0 26.0 39.0 27.0 14.444 54.0 28.889 81.0 43.333 30 60 90 52.0 108.0 57.778 120 78.0 162.0 86.667 180 864 104.0 216.0 115.556 240 972 117.0 243.0 130.000 270 1080 130.0 270.0 144.444 300 Symbol Explanation NSS R Number of spatial streams Code rate NBPSC Number of coded bits per single carrier NCBPS Number of coded bits per symbol NDBPS Number of data bits per symbol GI guard interval Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 4 of 44
: Sep. 23, 2011 3.2. Accessories Report No.: FR171226-02AB Power Brand Model Rating PIE LEI AD8180LF NU60-H120500-I1 Others Input:100V~240V, 50/60Hz 1.5A Output:12V - 5.0A Input: 100V~240V, 50/60Hz 1.4A Output: 12V - 5.0A Adapter 1 Adapter 2 RJ45 Cable 3.3. Table for Filed Antenna Ant. Brand Model Name Antenna Type Connector Gain (dBi) Remark 1 2 3
-
-
-
-
-
-
Printed Antenna Printed Antenna Printed Antenna NA NA NA 4.21 4.36 4.03 TX/RX TX/RX TX/RX Note: The EUT has three antennas. (1TX/1RX) Ant. 1, Ant. 2, and Ant. 3 can be used as transmitting/receiving antennas, but only one antenna can be used as transmitting/receiving antenna at the same time. The EUT supports the antenna with TX/RX diversity function. Due to the Ant. 3 generated highest output power, all the tests were base on this setting and recorded in this report. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 5 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 3.4. Table for Carrier Frequencies For IEEE 802.11a, use Channel 149, 153, 157, 161, 165. There are two bandwidth systems for IEEE 802.11n. For 20MHz bandwidth systems, use Channel 149, 153, 157, 161, 165. For 40MHz bandwidth systems, use Channel 151, 159. Frequency Band Channel No. Frequency Channel No. Frequency 5725~5850 MHz Band 4 3.5. Table for Test Modes 149 151 153 157 5745 MHz 5755 MHz 5765 MHz 5785 MHz 159 161 165
-
5795 MHz 5805 MHz 5825 MHz
-
Preliminary tests were performed in different data rate to find the worst radiated emission. The data rate shown in the table below is the worst-case rate with respect to the specific test item. Investigation has been done on all the possible configurations for searching the worst cases. The following table is a list of the test modes shown in this test report. Test Items Mode Data Rate Channel Antenna Maximum Conducted Output Power Average Output Power Power Spectral Density 6dB Spectrum Bandwidth Radiated Emissions Above 1GHz Band Edge Emissions MCS0/20MHz MCS0/40MHz 11a/BPSK MCS0/20MHz MCS0/40MHz 11a/BPSK MCS0/20MHz MCS0/40MHz 11a/BPSK MCS0/20MHz MCS0/40MHz 11a/BPSK 7.2 Mbps 149/157/165 14.4 Mbps 151/159 6 Mbps 149/157/165 7.2 Mbps 149/157/165 14.4 Mbps 151/159 6 Mbps 149/157/165 7.2 Mbps 149/157/165 14.4 Mbps 151/159 6 Mbps 149/157/165 7.2 Mbps 149/157/165 14.4 Mbps 151/159 6 Mbps 149/157/165 3 3 3 3 3 3 3 3 3 3 3 3 3.6. Table for Testing Locations Test Site No. Site Category 03CH01-CB SAC TH01-CB OVEN Room Location Hsin Chu Hsin Chu FCC Reg. No. IC File No. VCCI Reg. No 262045 IC 4086D
-
-
-
-
Open Area Test Site (OATS); Semi Anechoic Chamber (SAC); Fully Anechoic Chamber (FAC). Please refer section 6 for Test Site Address. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 6 of 44
: Sep. 23, 2011 3.7. Table for Class II Change Report No.: FR171226-02AB This product is an extension of original one reported under Sporton project number: FR171226AB Below is the table for the change of the product with respect to the original one. Description Performance Checking The operating test configuration of EUT for 5GHz Band was changed from 3TX/3RX to 1TX/1RX, and it was controlled by software. There is no change in both hardware and existing RF relevant portion. Maximum Conducted Output Power Average Output Power Power Spectral Density 6dB Spectrum Bandwidth Radiated Emissions above 1GHz test Band Edge Emissions 3.8. Table for Supporting Units Support Unit Notebook Mouse Modem Flash Disk Flash Disk Notebook Notebook Brand DELL iCooky ACEEX Silicon Silicon DELL DELL Model 1200 AMS0706W DM1414 D33B01 D33B02 M1330 PP25L FCC ID E2K4965AGNM DoC IFAXDM1414 DoC DoC E2KWM3945ABG E2K4965AGNM Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 7 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 3.9. Table for Parameters of Test Software Setting During testing, Channel & Power Controlling Software provided by the customer was used to control the operating channel as well as the output power level. The RF output power selection is for the setting of RF output power expected by the customer and is going to be fixed on the firmware of the final end product. Power Parameters of IEEE 802.11n Test Software Version Frequency MCS0 20MHz 5745 MHz 120 Power Parameters of IEEE 802.11n Test Software Version Frequency MCS0 40MHz Power Parameters of IEEE 802.11a DOS V1.3.2. 5785 MHz 120 DOS V1.3.2. 5825 MHz 120 5755 MHz 108 5795 MHz 120 Test Software Version Frequency IEEE 802.11a 5745 MHz 118 DOS V1.3.2. 5785 MHz 120 5825 MHz 120 During the test, DOS V1.3.2. under WIN XP was executed the test program to control the EUT continuously transmit RF signal. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 8 of 44
: Sep. 23, 2011 3.10. Test Configurations 3.10.1. Radiation Emissions Test Configuration Report No.: FR171226-02AB 2 AC MAIN 1 EUT 1. POWER CABLE ,170+150 CM , NON-SHIELDED 2. RJ45 CABLE , 1000CM , NON-SHIELDED R J
-
1 1 R J
-
4 5 L P T P S 2
/
V G A D C U S B x 2 Notebook Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 9 of 44
: Sep. 23, 2011 4. TEST RESULT Report No.: FR171226-02AB 4.1. Maximum Conducted Output Power Measurement 4.1.1. Limit For systems operating in the 5725-5850 MHz band that are used exclusively for fixed, point-to-point operations may employ transmitting antennas with directional gain greater than 6 dBi without any corresponding reduction in transmitter conducted output power. 4.1.2. Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the spectrum analyzer. Spectrum Parameter Attenuation Setting Auto Span Frequency Encompass the entire emissions bandwidth (EBW) of the signal RB VB Detector Trace Sweep Time 4.1.3. Test Procedures 1MHz 3MHz Sample Average 100 Auto 1. 2. The transmitter output (antenna port) was connected to the spectrum analyzer. Test was performed in accordance with Measurement of Digital Transmission Systems Operating under Section 15.247 March 23, 2005. 3. When measuring maximum conducted output power with multiple antenna systems, add every result of the values by mathematic formula. 4.1.4. Test Setup Layout 4.1.5. Test Deviation There is no deviation with the original standard. 4.1.6. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 10 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 4.1.7. Test Result of Maximum Conducted Output Power Temperature Test Engineer Test Date 25 Allen Liu Aug. 18, 2011 Configuration IEEE 802.11n MCS0 20MHz / Ant. 3 Humidity 60%
Configurations IEEE 802.11n Channel Frequency Conducted Power
(dBm) Max. Limit
(dBm) 149 157 165 5745 MHz 5785 MHz 5825 MHz 27.95 27.70 27.54 30.00 30.00 30.00 Configuration IEEE 802.11n MCS0 40MHz / Ant. 3 Channel Frequency Conducted Power
(dBm) Max. Limit
(dBm) 151 159 5755 MHz 5795 MHz 24.51 27.44 30.00 30.00 Result Complies Complies Complies Result Complies Complies Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 11 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Temperature Test Engineer Test Date 25 Allen Liu Aug. 18, 2011 Configuration IEEE 802.11a / Ant. 3 Humidity 60%
Configurations IEEE 802.11a Channel Frequency Conducted Power
(dBm) Max. Limit
(dBm) 149 157 165 5745 MHz 5785 MHz 5825 MHz 27.86 27.60 27.83 30.00 30.00 30.00 Result Complies Complies Complies Note: All the test values were listed in the report. For plots, only the channel with maximum results was shown. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 12 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Conducted Output Power Plot on Configuration IEEE 802.11n MCS0 20MHz Ant. 3 / 5745 MHz Date: 18.AUG.2011 20:01:41 Conducted Output Power Plot on Configuration IEEE 802.11n MCS0 40MHz Ant. 3 / 5795 MHz Date: 22.AUG.2011 11:33:54 Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 13 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Conducted Output Power Plot on Configuration IEEE 802.11a Ant. 3 / 5745 MHz Date: 22.AUG.2011 11:28:32 Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 14 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 4.2. Power Spectral Density Measurement 4.2.1. Limit For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8dBm in any 3 kHz band during any time interval of continuous transmission. 4.2.2. Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the spectrum analyzer. Spectrum Parameter Setting Attenuation Span Frequency RB VB Detector Trace Sweep Time Auto 30 kHz 3 kHz 30 kHz Peak Max Hold 10s 4.2.3. Test Procedures The transmitter output (antenna port) was connected to the spectrum analyzer. Set RBW of spectrum analyzer to 3kHz and VBW to 30kHz. Set Detector to Peak, Trace to Max Hold. 1. 2. 3. Mark the frequency with maximum peak power as the center of the display of the spectrum. 4. 5. When measuring power spectral density with multiple antenna systems, add every result of the Set the span to 30kHz and the sweep time to 10s and record the maximum peak value. values by mathematic formula. 4.2.4. Test Setup Layout 4.2.5. Test Deviation There is no deviation with the original standard. 4.2.6. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 15 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 4.2.7. Test Result of Power Spectral Density Temperature Test Engineer 25 Allen Liu Humidity 60%
Configurations IEEE 802.11n Configuration IEEE 802.11n MCS0 20MHz / Ant. 3 Channel Frequency Power Density
(dBm/3kHz) Max. Limit
(dBm/3kHz) 149 157 165 5745 MHz 5785 MHz 5825 MHz 4.41 4.03 1.98 8.00 8.00 8.00 Configuration IEEE 802.11n MCS0 40MHz / Ant. 3 Channel Frequency Power Density
(dBm/3kHz) Max. Limit
(dBm/3kHz) 151 159 5755 MHz 5795 MHz 2.84 3.25 8.00 8.00 Result Complies Complies Complies Result Complies Complies Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 16 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Temperature Test Engineer 25 Allen Liu Configuration IEEE 802.11a / Ant. 3 Channel Frequency Humidity 60%
Configurations IEEE 802.11a Power Density
(dBm/3kHz) Max. Limit
(dBm/3kHz) 149 157 165 5745 MHz 5785 MHz 5825 MHz 2.61 4.38 1.62 8.00 8.00 8.00 Note: All the test values were listed in the report. For plots, only the channel with maximum results was shown. Result Complies Complies Complies Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 17 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Power Density Plot on Configuration IEEE 802.11n MCS0 20MHz / Ant. 3 / 5745 MHz Ref 20 dBm 20 Offset 31 dB
*
Att 30 dB
*
*
*
*
RBW 3 kHz VBW 30 kHz SWT 10 s Marker 1 [T1 ]
4.41 dBm 5.746870560 GHz 1 A LVL 3DB 1 PK VIEW 10 0
-10
-20
-30
-40
-50
-60
-70
-80 Center 5.74687092 GHz 3 kHz/
Span 30 kHz Date: 18.AUG.2011 03:39:08 Power Density Plot on Configuration IEEE 802.11n MCS0 40MHz / Ant. 3 / 5795 MHz Ref 20 dBm 20 Offset 11 dB
*
Att 30 dB
*
*
*
*
RBW 3 kHz VBW 30 kHz SWT 10 s Marker 1 [T1 ]
3.25 dBm 5.793107020 GHz 1 A LVL 3DB 1 PK VIEW 10 0
-10
-20
-30
-40
-50
-60
-70
-80 Center 5.79310696 GHz 3 kHz/
Span 30 kHz Date: 18.AUG.2011 02:15:19 Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 18 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Power Density Plot on Configuration IEEE 802.11a / Ant. 3 / 5785 MHz Ref 20 dBm 20 Offset 31 dB
*
Att 30 dB
*
*
*
*
RBW 3 kHz VBW 30 kHz SWT 10 s Marker 1 [T1 ]
4.38 dBm 5.779988220 GHz 1 A LVL 3DB 1 PK VIEW 10 0
-10
-20
-30
-40
-50
-60
-70
-80 Center 5.77998816 GHz 3 kHz/
Span 30 kHz Date: 18.AUG.2011 03:45:15 Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 19 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 4.3. 6dB Spectrum Bandwidth Measurement 4.3.1. Limit For digital modulation systems, the minimum 6dB bandwidth shall be at least 500 kHz. 4.3.2. Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the spectrum analyzer. Spectrum Parameters Setting Attenuation Auto Span Frequency
> 6dB Bandwidth RB VB Detector Trace Sweep Time 100 kHz 100 kHz Peak Max Hold Auto 4.3.3. Test Procedures 1. The transmitter output (antenna port) was connected to the spectrum analyzer in peak hold mode. 2. The resolution bandwidth of 100 kHz and the video bandwidth of 100 kHz were used. 3. Measured the spectrum width with power higher than 6dB below carrier. 4.3.4. Test Setup Layout 4.3.5. Test Deviation There is no deviation with the original standard. 4.3.6. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 20 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Humidity 60%
Configurations IEEE 802.11n 4.3.7. Test Result of 6dB Spectrum Bandwidth Temperature Test Engineer 25 Allen Liu Test Date Jul. 09, 2011 Configuration IEEE 802.11n MCS0 20MHz / Ant. 3 Channel Frequency 6dB Bandwidth
(MHz) 99% Occupied Bandwidth
(MHz) 149 157 165 5745 MHz 5785 MHz 5825 MHz 16.40 16.36 16.48 16.84 16.84 16.60 Configuration IEEE 802.11n MCS0 40MHz / Ant. 3 Channel Frequency 6dB Bandwidth
(MHz) 99% Occupied Bandwidth
(MHz) 151 159 5755 MHz 5795 MHz 36.32 36.32 36.32 36.32 500 500 Min. Limit
(kHz) 500 500 500 Min. Limit
(kHz) Test Result Complies Complies Complies Test Result Complies Complies Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 21 of 44
: Sep. 23, 2011 Temperature Test Engineer 25 Allen Liu Test Date Jul. 09, 2011 Configuration IEEE 802.11a / Ant. 3 Channel Frequency 6dB Bandwidth
(MHz) Report No.: FR171226-02AB Humidity 60%
Configurations IEEE 802.11a 99% Occupied Bandwidth
(MHz) Min. Limit
(kHz) 500 500 500 Test Result Complies Complies Complies 149 157 165 5745 MHz 5785 MHz 5825 MHz 16.44 16.36 16.44 16.60 16.76 16.60 Note: All the test values were listed in the report. For plots, only the channel with maximum results was shown. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 22 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 6 dB Bandwidth Plot on Configuration IEEE 802.11n MCS0 20MHz / Ant. 3 / 5785 MHz Ref 20 dBm 20
*
Att 30 dB
*
*
*
*
RBW 100 kHz VBW 100 kHz SWT 100 ms Delta 1 [T1 ]
-0.21 dB 16.360000000 MHz OBW 16.840000000 MHz Marker 1 [T1 ]
6.28 dBm 1 5.776800000 GHz Temp 1 [T1 OBW]
-1.64 dBm 5.776560000 GHz Temp 2 [T1 OBW]
-2.20 dBm 5.793400000 GHz T2 A 3DB F2 2 MHz/
Span 20 MHz D1 10.748 dBm D2 4.748 dBm 1 T1 1 PK VIEW 10 0
-10
-20
-30
-40
-50
-60
-70 F1
-80 Center 5.785 GHz Date: 18.AUG.2011 02:03:45 6 dB Bandwidth Plot on Configuration IEEE 802.11n MCS0 40MHz / Ant. 3 / 5755MHz Ref 20 dBm 20
*
Att 30 dB
*
*
*
*
RBW 100 kHz VBW 100 kHz SWT 100 ms 1 PK VIEW 10 0 1 T1 D1 4.676 dBm D2 -1.324 dBm
-10
-20
-30
-40
-50
-60 Delta 1 [T1 ]
-0.13 dB 36.320000000 MHz OBW 36.320000000 MHz Marker 1 [T1 ]
-0.37 dBm 5.736840000 GHz Temp 1 [T1 OBW]
-0.37 dBm 5.736840000 GHz Temp 2 [T1 OBW]
-0.49 dBm 5.773160000 GHz T2 1 A 3DB
-70 F1
-80 Center 5.755 GHz F2 4 MHz/
Span 40 MHz Date: 18.AUG.2011 02:11:39 Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 23 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 6 dB Bandwidth Plot on Configuration IEEE 802.11a / Ant. 3 / 5785 MHz Delta 1 [T1 ]
0.20 dB 16.360000000 MHz OBW 16.760000000 MHz Marker 1 [T1 ]
5.18 dBm 1 5.776800000 GHz T2 Temp 1 [T1 OBW]
-3.70 dBm 5.776560000 GHz Temp 2 [T1 OBW]
0.33 dBm 5.793320000 GHz RBW 100 kHz VBW 100 kHz SWT 100 ms Ref 20 dBm 20 D1 9.923 dBm D2 3.923 dBm Att 30 dB 1 PK VIEW
-10
*
*
*
*
T1 10 1
*
0 A 3DB
-20
-30
-40
-50
-60
-70 F1
-80 Center 5.785 GHz Date: 18.AUG.2011 01:54:44 F2 2 MHz/
Span 20 MHz Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 24 of 44
: Sep. 23, 2011 4.4. Radiated Emissions Measurement 4.4.1. Limit Report No.: FR171226-02AB 20dBc in any 100 kHz bandwidth outside the operating frequency band. In case the emission fall within the restricted band specified on 15.205(a), then the 15.209(a) limit in the table below has to be followed. Frequencies
(MHz) 0.009~0.490 0.490~1.705 1.705~30.0 30~88 88~216 216~960 Above 960 Field Strength
(micorvolts/meter) 2400/F(KHz) 24000/F(KHz) 30 100 150 200 500 Measurement Distance
(meters) 300 30 30 3 3 3 3 4.4.2. Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of spectrum analyzer and receiver. Receiver Parameter Attenuation Start ~ Stop Frequency Start ~ Stop Frequency Start ~ Stop Frequency Setting Auto 9kHz~150kHz / RB 200Hz for QP 150kHz~30MHz / RB 9kHz for QP 30MHz~1000MHz / RB 120kHz for QP Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 25 of 44
: Sep. 23, 2011 4.4.3. Test Procedures Report No.: FR171226-02AB 1. Configure the EUT according to ANSI C63.10. The EUT was placed on the top of the turntable 0.8 meter above ground. The phase center of the receiving antenna mounted on the top of a height-variable antenna tower was placed 3 meters far away from the turntable. 2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to 3. determine the position of the highest radiation. The height of the broadband receiving antenna was varied between one meter and four meters above ground to find the maximum emissions field strength of both horizontal and vertical polarization. 4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was rotated (from 0 degree to 360 degrees) to find the maximum reading. 5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with specified bandwidth under Maximum Hold Mode. 6. For emissions above 1GHz, use 1MHz VBW and RBW for peak reading. Then 1MHz RBW and 10Hz VBW for average reading in spectrum analyzer. 7. When the radiated emissions limits are expressed in terms of the average value of the emissions, and pulsed operation is employed, the measurement field strength shall be determined by averaging over one complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds. As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average absolute voltage during a 0.1 second interval during which the field strength is at its maximum value. If the emissions level of the EUT in peak mode was 3 dB lower than the average limit specified, then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 3 dB margin will be repeated one by one using the quasi-peak method for below 1GHz. 8. 9. For testing above 1GHz, the emissions level of the EUT in peak mode was lower than average limit
(that means the emissions level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. 10. In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the recorded data should be QP measured by receiver. High Low scan is not required in this case. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 26 of 44
: Sep. 23, 2011 4.4.4. Test Setup Layout Report No.: FR171226-02AB 3 or 1.5m Above 5GHz shall be extrapolated to the specified distance using an extrapolation factor of 20 dB/decade from 3m to 1.5m. Distance extrapolation factor = 20 log (specific distance [3m] / test distance [1.5m]) (dB);
Limit line = specific limits (dBuV) + distance extrapolation factor [6 dB]. 4.4.5. Test Deviation There is no deviation with the original standard. 4.4.6. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 27 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 4.4.7. Results for Radiated Emissions (1GHz~10th Harmonic) Temperature 25.6 Humidity 56%
Test Engineer Robert Chang Configurations IEEE 802.11n MCS0 20MHz CH 149 /
Ant. 3 Test Date Horizontal Aug. 19, 2011 Vertical Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 28 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Temperature 25.6 Humidity 56%
Test Engineer Robert Chang Configurations IEEE 802.11n MCS0 20MHz CH 157 /
Ant. 3 Test Date Horizontal Aug. 19, 2011 Vertical Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 29 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Temperature 25.6 Humidity 56%
Test Engineer Robert Chang Configurations IEEE 802.11n MCS0 20MHz CH 165 /
Ant. 3 Test Date Horizontal Aug. 19, 2011 Vertical Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 30 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Temperature 25.6 Humidity 56%
Test Engineer Robert Chang Configurations IEEE 802.11n MCS0 40MHz CH 151 /
Ant. 3 Test Date Horizontal Aug. 19, 2011 Vertical Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 31 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Temperature 25.6 Humidity 56%
Test Engineer Robert Chang Configurations IEEE 802.11n MCS0 40MHz CH 159 /
Ant. 3 Test Date Horizontal Aug. 19, 2011 Vertical Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 32 of 44
: Sep. 23, 2011 Temperature Test Engineer Test Date Horizontal 25.6 Robert Chang Aug. 19, 2011 Report No.: FR171226-02AB Humidity 56%
Configurations IEEE 802.11a CH 149 / Ant. 3 Vertical Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 33 of 44
: Sep. 23, 2011 Temperature Test Engineer Test Date Horizontal 25.6 Robert Chang Aug. 19, 2011 Report No.: FR171226-02AB Humidity 56%
Configurations IEEE 802.11a CH 157 / Ant. 3 Vertical Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 34 of 44
: Sep. 23, 2011 Temperature Test Engineer Test Date Horizontal 25.6 Robert Chang Aug. 19, 2011 Vertical Report No.: FR171226-02AB Humidity 56%
Configurations IEEE 802.11a CH 165 / Ant. 3 Note:
The amplitude of spurious emissions that are attenuated by more than 20dB below the permissible value has no need to be reported. Emission level (dBuV/m) = 20 log Emission level (uV/m). Corrected Reading: Antenna Factor + Cable Loss + Read Level - Preamp Factor = Level. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 35 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 4.5. Band Edge Emissions Measurement 4.5.1. Limit 20dBc in any 100 kHz bandwidth outside the operating frequency band. In case the emission fall within the restricted band specified on 15.205(a), then the 15.209(a) limit in the table below has to be followed. Frequencies
(MHz) 0.009~0.490 0.490~1.705 1.705~30.0 30~88 88~216 216~960 Above 960 Field Strength
(micorvolts/meter) 2400/F(KHz) 24000/F(KHz) 30 100 150 200 500 Measurement Distance
(meters) 300 30 30 3 3 3 3 4.5.2. Measuring Instruments and Setting Please refer to section 5 of equipments list in this report. The following table is the setting of the spectrum analyzer. Spectrum Parameter Attenuation Span Frequency Setting Auto 100 MHz RB / VB (Emission in restricted band) 1MHz / 1MHz for Peak, 1 MHz / 10Hz for Average RB / VB (Emission in non-restricted band) 100 KHz /100 KHz for Peak 4.5.3. Test Procedures 1. 2. The test procedure is the same as section 4.5.3, only the frequency range investigated is limited to 100MHz around bandedges. In case the emission is fail due to the used RB/VB is too wide, marker-delta method of FCC Public Notice DA00-705 will be followed. 4.5.4. Test Setup Layout This test setup layout is the same as that shown in section 4.5.4. 4.5.5. Test Deviation There is no deviation with the original standard. 4.5.6. EUT Operation during Test The EUT was programmed to be in continuously transmitting mode. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 36 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 4.5.7. Test Result of Band Edge and Fundamental Emissions For Emission not in Restricted Band Low Band Edge Plot on Configuration IEEE 802.11n MCS0 20MHz / Ant. 3 / 5745 MHz Ref 97 dBV
*
Att 0 dB
*
*
RBW 100 kHz VBW 100 kHz SWT 20 ms D1 79.32 dBV 1 D2 49.32 dBV 1 RM VIEW
*
90 80 70 60 50 40 30 20 10 Delta 1 [T1 ]
31.46 dB 65.032051282 MHz Marker 1 [T1 ]
47.85 dBV 5.725000000 GHz A 1 3DB 0 Center 5.747724359 GHz F1 10 MHz/
Span 100 MHz Date: 19.AUG.2011 18:49:07 High Band Edge Plot on Configuration IEEE 802.11n MCS0 20MHz / Ant. 3 / 5825 MHz
*
*
RBW 100 kHz VBW 100 kHz SWT 20 ms Delta 1 [T1 ]
37.05 dB
-64.423076923 MHz Marker 1 [T1 ]
41.33 dBV 5.850679487 GHz A 3DB 1 F1 10 MHz/
Stop 5.876 GHz Ref 97 dBV
*
Att 0 dB 1 D1 78.39 dBV D2 48.39 dBV 1 RM VIEW
*
90 80 70 60 50 40 30 20 10 0 Start 5.776 GHz Date: 19.AUG.2011 18:26:49 Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 37 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Low Band Edge Plot on Configuration IEEE 802.11n MCS0 40MHz / Ant. 3 / 5755 MHz Ref 97 dBV
*
Att 0 dB
*
*
RBW 100 kHz VBW 100 kHz SWT 20 ms D1 76.66 dBV Delta 1 [T1 ]
32.09 dB 74.679487179 MHz Marker 1 [T1 ]
44.57 dBV 5.722435897 GHz A 1 D2 46.66 dBV 1 3DB 1 RM VIEW
*
90 80 70 60 50 40 30 20 10 1 RM VIEW
*
90 80 70 60 50 40 30 20 10 0 Center 5.723397436 GHz F1 20 MHz/
Span 200 MHz Date: 19.AUG.2011 19:51:45 High Band Edge Plot on Configuration IEEE 802.11n MCS0 40MHz / Ant. 3 / 5795 MHz Ref 97 dBV
*
Att 0 dB
*
*
RBW 100 kHz VBW 100 kHz SWT 20 ms Delta 1 [T1 ]
32.79 dB
-106.410256410 MHz Marker 1 [T1 ]
43.46 dBV 5.857692308 GHz A 1 D1 76.24 dBV D2 46.24 dBV 1 3DB 0 Center 5.808333333 GHz F1 20 MHz/
Span 200 MHz Date: 19.AUG.2011 19:32:26 Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 38 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Low Band Edge Plot on Configuration IEEE 802.11a / Ant. 3 / 5745 MHz Ref 97 dBV
*
Att 0 dB
*
*
RBW 100 kHz VBW 100 kHz SWT 20 ms D1 78.64 dBV D2 48.64 dBV 1 1 RM VIEW
*
90 80 70 60 50 40 30 20 10 Delta 1 [T1 ]
31.13 dB 65.076923077 MHz Marker 1 [T1 ]
47.51 dBV 5.725000000 GHz 1 A 3DB 0 Start 5.692 GHz F1 10 MHz/
Stop 5.792 GHz Date: 19.AUG.2011 18:20:04 High Band Edge Plot on Configuration IEEE 802.11a / Ant. 3 / 5825 MHz
*
*
RBW 100 kHz VBW 100 kHz SWT 20 ms Delta 1 [T1 ]
35.69 dB
-77.564102564 MHz Marker 1 [T1 ]
42.38 dBV 5.856288462 GHz A 1 3DB Ref 97 dBV
*
Att 0 dB D1 78.07 dBV D2 48.07 dBV 1 RM VIEW
*
90 1 80 70 60 50 40 30 20 10 0 Start 5.776 GHz F1 10 MHz/
Stop 5.876 GHz Date: 19.AUG.2011 18:22:51 Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 39 of 44
: Sep. 23, 2011 4.6. Antenna Requirements 4.6.1. Limit Report No.: FR171226-02AB Except for special regulations, the Low-power Radio-frequency Devices must not be equipped with any jacket for installing an antenna with extension cable. An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this Section. The manufacturer may design the unit so that the user can replace a broken antenna, but the use of a standard antenna jack or electrical connector is prohibited. Further, this requirement does not apply to intentional radiators that must be professionally installed. 4.6.2. Antenna Connector Construction Please refer to section 3.3 in this test report; antenna connector complied with the requirements. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 40 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB 5. LIST OF MEASURING EQUIPMENTS Instrument Manufacturer Model No. Serial No. Characteristics Calibration Date Horn Antenna EMCO 3115 00075790 750MHz~18GHz Nov. 22, 2010 Horn Antenna SCHWARZBEAK BBHA 9170 BBHA9170252 15GHz ~ 40GHz Oct. 08, 2010 Pre-Amplifier Agilent 8449B 3008A02310 1GHz ~ 26.5GHz Nov. 23, 2010 Pre-Amplifier Spectrum analyzer WM R&S TF-130N-R1 923365 26.5GHz ~ 40GHz Nov. 17, 2010 FSP 100304 9kHz ~ 40GHz Nov. 22, 2010 Turn Table INN CO CO 2000 Antenna Mast INN CO CO2000 RF Cable-high Woken High Cable-1 RF Cable-high Woken High Cable-2 RF Cable-high Woken High Cable-3 RF Cable-high Woken High Cable-4 N/A N/A N/A N/A N/A N/A 0 360 degree 1 m - 4 m N/A N/A 1 GHz 26.5 GHz Nov. 17, 2010 1 GHz 26.5 GHz Nov. 17, 2010 1 GHz - 40 GHz Nov. 17, 2010 1 GHz - 40 GHz Nov. 17, 2010 Spectrum analyzer R&S FSV30 101026 9KHz~30GHz Jul. 23, 2011 Ten Billion TTH-D3SP TBN-931011
-30~100 degree May 20, 2011 Temp. and Humidity Chamber Thermo-Hygro Meter RF Power Divider N/A HP RF Power Splitter Anaren RF Power Splitter Anaren HC 520 11636A 44100 42100
#1 15~70 degree Nov. 02, 2010 00306 2GHz ~ 18GHz 1839 2GHz ~ 18GHz 17930 2GHz ~ 18GHz N/A N/A N/A Horn Antenna COM-POWER AH-118 071187 1GHz 18GHz Mar. 18, 2011 RF Cable-high Woken High Cable-7 RF Cable-high Woken High Cable-8 RF Cable-high Woken High Cable-9 RF Cable-high Woken High Cable-10 RF Cable-high Woken High Cable-11 RF Cable-high Woken High Cable-12 RF Cable-high Woken High Cable-13
-
-
-
-
-
-
-
1 GHz 26.5 GHz Nov. 17, 2010 1 GHz 26.5 GHz Nov. 17, 2010 1 GHz 26.5 GHz Nov. 17, 2010 1 GHz 26.5 GHz Nov. 17, 2010 1 GHz 26.5 GHz Nov. 17, 2010 1 GHz 26.5 GHz Nov. 17, 2010 1 GHz 26.5 GHz Nov. 17, 2010 Power Sensor Anritsu MA2411B 0917223 300MHz~40GHz Sep. 13, 2010 Remark Radiation
(03CH01-CB) Radiation
(03CH01-CB) Radiation
(03CH01-CB) Radiation
(03CH01-CB) Radiation
(03CH01-CB) Radiation
(03CH01-CB) Radiation
(03CH01-CB) Radiation
(03CH01-CB) Radiation
(03CH01-CB) Radiation
(03CH01-CB) Radiation
(03CH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Conducted
(TH01-CB) Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 41 of 44
: Sep. 23, 2011 Report No.: FR171226-02AB Instrument Manufacturer Model No. Serial No. Characteristics Calibration Date Power Meter Anritsu ML2495A 1035008 300MHz~40GHz Sep. 08, 2010 Remark Conducted
(TH01-CB) Note: Calibration Interval of instruments listed above is one year. Note: * Calibration Interval of instruments listed above is two years. Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 42 of 44
: Sep. 23, 2011 6. TEST LOCATION Report No.: FR171226-02AB SHIJR ADD
: 6Fl., No. 106, Sec. 1, Shintai 5th Rd., Shijr City, Taipei, Taiwan 221, R.O.C. TEL
: 886-2-2696-2468 FAX
: 886-2-2696-2255 HWA YA ADD
: No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, Tao Yuan Hsien, Taiwan, R.O.C. TEL
: 886-3-327-3456 FAX
: 886-3-318-0055 LINKOU ADD
: No. 30-2, Dingfu Tsuen, Linkou Shiang, Taipei, Taiwan 244, R.O.C TEL
: 886-2-2601-1640 FAX
: 886-2-2601-1695 DUNGHU ADD
: No. 3, Lane 238, Kangle St., Neihu Chiu, Taipei, Taiwan 114, R.O.C. TEL
: 886-2-2631-4739 FAX
: 886-2-2631-9740 JUNGHE ADD
: 7Fl., No. 758, Jungjeng Rd., Junghe City, Taipei, Taiwan 235, R.O.C. TEL
: 886-2-8227-2020 FAX
: 886-2-8227-2626 NEIHU ADD
: 4Fl., No. 339, Hsin Hu 2nd Rd., Taipei 114, Taiwan, R.O.C. TEL
: 886-2-2794-8886 FAX
: 886-2-2794-9777 JHUBEI ADD
: No.8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C. TEL
: 886-3-656-9065 FAX
: 886-3-656-9085 Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 43 of 44
: Sep. 23, 2011 7. TAF CERTIFICATE OF ACCREDITATION Report No.: FR171226-02AB Report Format Version: 01 FCC ID: PY311200162 Page No. Issued Date
: 44 of 44
: Sep. 23, 2011
1 2 3 4 | Test Setup Photos | Test Setup Photos | 76.21 KiB | September 28 2011 / March 26 2012 |
Report No.: FR171226-02 Appendix A. Test Photos FCC ID: PY311200162 Page No.
: 1 of 2 Report No.: FR171226-02 1. Photographs of Radiated Emissions Test Configuration Test Configuration: Above 1GHz FRONT VIEW REAR VIEW FCC ID: PY311200162 Page No.
: 2 of 2
1 2 3 4 | DoC letter | Cover Letter(s) | 24.16 KiB | July 29 2011 |
NETGEAR, Inc. 350 East Plumeria Drive, San Jose, California 95134-1911, USA Tel: +1 408 907 8000 Fax: +1 408 907 8097 DoC Attestation Letter Date: 2011/7/18 We NETGEAR, Inc., as the grantee of this project FCC ID: PY311200162, would like to declare that the composite portion categorized as computer peripheral has been authorized under the Declaration of Conformity procedures. Regards, FCC Grantee contact person information. Applicants company name
: NETGEAR, Inc. Applicants company address : 350 East Plumeria Drive, San Jose, California 95134-1911, USA Signature
:
_____________________________ Job Title and Dept.
: Mark Gandler / Compliance Manager E-Mail Tel.
: mark.gandler@netgear.com
: +1 408 907 8000 Page No.
: 15
1 2 3 4 | co location report | Test Report | 104.34 KiB | July 29 2011 |
Report No.: FR171226 Appendix C. Co-location FCC ID: PY311200162 Page No.
: C1 of C3 Report No.: FR171226 1. Results of Radiated Emissions for Co-located Temperature Test Engineer Horizontal 22 Allen Liu Humidity 60%
Configurations 2.4G + 5G FCC ID: PY311200162 Page No.
: C2 of C3 Vertial Report No.: FR171226 FCC ID: PY311200162 Page No.
: C3 of C3
1 2 3 4 | request for confidentiality | Cover Letter(s) | 58.17 KiB | July 29 2011 |
NETGEAR, Inc. 350 East Plumeria Drive, San Jose, California 95134-1911, USA Tel: +1 408 907 8000 Fax: +1 408 907 8097 Date: 2011/7/18 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7345 Oakland Mills Road Columbia, Maryland 21046 Subject: Confidentiality Request for FCC IDPY311200162 Gentlemen:
The form 731 and application have been electronically submitted and any attachments will be up loaded to your web site to be used in obtaining a grant of certification. Short-term Pursuant to DA 04-1705 of the Commissions pubic notice, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:
1. 2. 3. 4. Permanent NETGEAR, Inc. requests that the material in the following files be withheld from public disclosure in accordance with Section 0.459 of the Commissions Rules, 47 C.F.R. 0.459, following grant of the application. 1. Block Diagram 2. Circuit Diagram 3. Operational Description Should you require any further information, please contact the undersigned. Thank you for your consideration in this matter. External Photos Internal Photos Test Setup photos Users Manual Sincerely, Applicants company name
: NETGEAR, Inc. Applicants company address : 350 East Plumeria Drive, San Jose, California 95134-1911, USA Signature
:
_____________________________ Job Title and Dept.
: Mark Gandler / Compliance Manager
: mark.gandler@netgear.com
: +1 408 907 8000 E-Mail Tel. Page No.
: 9
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2011-09-28 | 5755 ~ 5795 | DTS - Digital Transmission System | Class II Permissive Change |
2 | 5190 ~ 5240 | NII - Unlicensed National Information Infrastructure TX | ||
3 | 2011-07-29 | 5190 ~ 5240 | NII - Unlicensed National Information Infrastructure TX | Original Equipment |
4 | 5755 ~ 5795 | DTS - Digital Transmission System |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 3 4 | Effective |
2011-09-28
|
||||
1 2 3 4 |
2011-07-29
|
|||||
1 2 3 4 | Applicant's complete, legal business name |
Netgear Incorporated
|
||||
1 2 3 4 | FCC Registration Number (FRN) |
0022158786
|
||||
1 2 3 4 | Physical Address |
350 East Plumeria Drive
|
||||
1 2 3 4 |
San Jose, CA
|
|||||
1 2 3 4 |
United States
|
|||||
app s | TCB Information | |||||
1 2 3 4 | TCB Application Email Address |
B******@phoenix-testlab.de
|
||||
1 2 3 4 |
b******@phoenix-testlab.de
|
|||||
1 2 3 4 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 2 3 4 | Grantee Code |
PY3
|
||||
1 2 3 4 | Equipment Product Code |
11200162
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 3 4 | Name |
D****** K****
|
||||
1 2 3 4 | Telephone Number |
40889********
|
||||
1 2 3 4 | Fax Number |
40890********
|
||||
1 2 3 4 |
d******@netgear.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 3 4 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 3 4 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 3 4 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 03/26/2012 | ||||
1 2 3 4 | 01/25/2012 | |||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 3 4 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 3 4 | Equipment Class | DTS - Digital Transmission System | ||||
1 2 3 4 | NII - Unlicensed National Information Infrastructure TX | |||||
1 2 3 4 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | N900 Wireless Dual Band Gigabit Router | ||||
1 2 3 4 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 3 4 | Modular Equipment Type | Does not apply | ||||
1 2 3 4 | Purpose / Application is for | Class II Permissive Change | ||||
1 2 3 4 | Original Equipment | |||||
1 2 3 4 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 3 4 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 3 4 | Grant Comments | Output Power listed is the maximum combined conducted peak output power as indicated in the filing. This device must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter otherwise documented in this filing. End-users must be provided transmitter operating conditions for satisfying RF exposure compliance. Device is operating in a 3T3R Spatial Multiplexing MIMO configuration as described in this filing. When operating in 802.11n, 40MHz mode, the operating frequency segment is limited to 2422 to 2452MHz and 5755 to 5795MHz respectively. Class II Permissive Change Filing. Within the 5GHz band the device is now operating in a 1T1R Spatial Multiplexing MIMO configuration with following max peak power values: 0.624W (5745 - 5825MHz) and 0.555W (5755 - 5795MHz). | ||||
1 2 3 4 | Output Power listed is the maximum combined conducted peak output power as indicated in the filing. This device must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter otherwise documented in this filing. End-users must be provided transmitter operating conditions for satisfying RF exposure compliance. Device is operating in a 3T3R Spatial Multiplexing MIMO configuration as described in this filing. Operating of this device in the 5150 MHz to 5250 MHz range is restricted to indoor use only. Class II Permissive Change Filing. Device is now operating in a 1T1R Spatial Multiplexing MIMO configuration with following max peak power values: 0.048W (5180 - 5240MHz) and 0.047W (5190 - 5230MHz). | |||||
1 2 3 4 | Output Power listed is the maximum combined conducted peak output power as indicated in the filing. This device must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter otherwise documented in this filing. End-users must be provided transmitter operating conditions for satisfying RF exposure compliance. Device is operating in a 3T3R Spatial Multiplexing MIMO configuration as described in this filing. Operating of this device in the 5150 MHz to 5250 MHz range is restricted to indoor use only. | |||||
1 2 3 4 | Output Power listed is the maximum combined conducted peak output power as indicated in the filing. This device must be installed and operated to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter otherwise documented in this filing. End-users must be provided transmitter operating conditions for satisfying RF exposure compliance. Device is operating in a 3T3R Spatial Multiplexing MIMO configuration as described in this filing. When operating in 802.11n, 40 MHz mode, the operating frequency segment is limited to 2422 to 2452 MHz and 5755 to 5795 MHz respectively. | |||||
1 2 3 4 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 3 4 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 3 4 | Firm Name |
Sporton International Inc.
|
||||
1 2 3 4 | Name |
A**** C******
|
||||
1 2 3 4 | Telephone Number |
886-3******** Extension:
|
||||
1 2 3 4 | Fax Number |
886-3********
|
||||
1 2 3 4 |
a******@sporton.com.tw
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CC MO | 2412 | 2462 | 0.775 | |||||||||||||||||||||||||||||||||||
1 | 2 | 15C | CC MO | 2422 | 2452 | 0.262 | |||||||||||||||||||||||||||||||||||
1 | 3 | 15C | CC MO | 5745 | 5825 | 0.692 | |||||||||||||||||||||||||||||||||||
1 | 4 | 15C | CC MO | 5755 | 5795 | 0.667 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 15E | CC MO | 5180 | 5240 | 0.048 | |||||||||||||||||||||||||||||||||||
2 | 2 | 15E | CC MO | 5190 | 5240 | 0.049 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
3 | 1 | 15E | CC MO | 5180 | 5240 | 0.048 | |||||||||||||||||||||||||||||||||||
3 | 2 | 15E | CC MO | 5190 | 5240 | 0.049 | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
4 | 1 | 15C | CC MO | 2412 | 2462 | 0.775 | |||||||||||||||||||||||||||||||||||
4 | 2 | 15C | CC MO | 2422 | 2452 | 0.262 | |||||||||||||||||||||||||||||||||||
4 | 3 | 15C | CC MO | 5745 | 5825 | 0.692 | |||||||||||||||||||||||||||||||||||
4 | 4 | 15C | CC MO | 5755 | 5795 | 0.667 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC