FCC ID: PY326200664 Nighthawk 5G M8 Pro

Back of the device Battery compartment Label location Label locates in the battery compartment, and is viewable to the users as they install the battery.

pa FCC ID: PY326200664 t NETGEAR Model: MR8400 MAC: 3498B5860F B8 Nighthawk 5G M8 Pro IMEI-1: 354605950000016 IMEI-2: 354605950000024 SN: PPPDYMSCXXXXX MR8400-1A1NAS Nighthawk Manager: http://attwifimanager/

For indoor use only SKU: 6007G This device complies with part 15 ofthe FCC Rules. Operation is subject to the following two conditions: (1) This d may not cause |

FCC regulations restrict operation ofthis device or the 5 GHz UNII-4 band, Made in Indonesia rmful interference, and (2) this device any interference received, including interference that may cause undesired operat to indoor use only when itis operating in he 6 GHz band (5.925-7.125 GHz) ust accept

NETGEAR, INC. 3553 N. First St., San Jose, California 95134, United States Date: 2026-08-19 FCC ID: PY326200664 To the attention of:

Federal Communications Commission Authorization and Evaluation Division Declaration Letter for Low Power Indoor Access Points (6ID) We, NETGEAR, INC., attest that this device under FCC ID: PY326200664 complies with device protocol requirements and operational restrictions for Indoor Access Point Devices (6ID). a) The method used by this indoor access point to control the associated client/subordinate power control is as follows: As a IEEE 802.xx compliant device, the Transmit Power Envelope element transmitted by the product contains information fields on transmit power limits. The connecting client/subordinate device uses these TPE information to ensure it operates within the regulatory transmit power limits. The device beacon and probe response also ensure the connecting client/subordinate knows what type of device it is connecting to. b) This Low-Power Indoor Access Point operates in the 5.925-7.125 GHz band only when supplied power from a wired connection. Operation in this band is permitted only when the device is in plugged-in mode, as described in the user's manual. Before this band can be enabled through the device or web user interface, the end user must remove the battery and connect the device to a wall adapter. Accordingly, when operating in the 5.925-7.125 GHz band, the device is powered from a wired connection, is not battery-powered, has an integrated antenna, and does not have a weatherized enclosure. c) We acknowledge this device is subject to and in full compliance with the device restrictions listed below. All users are notified of these restrictions through the user manual. This device's operation will not be allowed on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet only in the 5.925-6.425 GHz band. This device is prohibited for control of or communications with unmanned aircraft systems, including drones. d) This device employs a Contention-Based Protocol as demonstrated in the test report. If you should have any questions regarding this declaration, please do not hesitate to contact us, thank you!

Sincerely yours,

John Ramones, Head of Product Design NETGEAR, INC. Tel: 4088903160 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 3553 North First Street, San Jose, CA 95134, USA U.S. Agent for Service of Process Attestation To the attention of Federal Communications Commission Authorization and Evaluation Division Applicant / Designated U.S Agent Company Name: NETGEAR, INC. FRN: 0035631530 Grantee Code: PY3 Contact Name: John Ramones Street Address: 3553 North First Street City/Province/Zip: San Jose, CA 95134, USA Telephone No: 4088903160 Email: [email protected] This letter is to confirm that the Applicant has designated itself as the U.S Agent for service of process as required by 2.911(d)(7). The Applicant further acknowledges acceptance to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment. Applicant / U.S. Agent Signature:

Date: 2025-10-23 Signed by (printed name): John Ramones

NETGEAR, INC. 3553 N. First St., San Jose, California 95134, United States Date: 2026-07-22 FCC ID: PY326200664 To the attention of Federal Communications Commission Authorization and Evaluation Division Attestation Statements Attestation Statements Part 2.911(d)(5)(i) Filing NETGEAR, INC. certifies that the equipment for which authorization is sought is not covered equipment prohibited from receivingan equipment authorization pursuant to section 2.903 of the FCC rules. Attestation Statements Part 2.911(d)(5)(ii) Filing NETGEAR, INC. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Sincerely yours,

John Ramones, Head of Product Design NETGEAR, INC. Tel: 4088903160 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 3553 N. First St., San Jose, California 95134, United States Date: 2026-07-22 FCC ID: PY326200664 To the attention of Federal Communications Commission Authorization and Evaluation Division Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below:

Schematics Block Diagram Operational Description Software Operational Description Parts List Tune Up Procedure The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely yours,

John Ramones, Head of Product Design NETGEAR, INC. Tel: 4088903160 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 3553 N. First St., San Jose, California 95134, United States Date: 2026-07-22 FCC ID: PY326200664 To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commissions rules, we request short-term confidential treatment for the following information until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:

External photos Test Setup photos Users manual Internal Photos Sincerely yours,

John Ramones, Head of Product Design NETGEAR, INC. Tel: 4088903160 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 3553 N. First St., San Jose, California 95134, United States Date: 2026-07-22 FCC ID: PY326200664 A U T H O R I Z A T I O N L E T T E R To Whom It May Concern:

NETGEAR, INC. hereby authorizes Jenny NIEN / Specialist of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan), to act on its behalf in all matters relating to the Federal Communication Commission (FCC) application for equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Jenny NIEN /

Specialist of BV CPS Taoyuan on NETGEAR, INC.s behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please dont hesitate to contact us. Sincerely yours,

John Ramones, Head of Product Design NETGEAR, INC. Tel: 4088903160 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 3553 N. First St., San Jose, California 95134, United States Date: 2026-08-14 FCC ID: PY326200664 To the attention of:

Federal Communications Commission Authorization and Evaluation Division Declaration Letter for Low Power Indoor Client Devices (6XD) We, NETGEAR, INC., attest that this device under FCC ID: PY326200664 complies with device protocol requirements and operational restrictions for Indoor Client Devices (6XD). a) This device will only associate and connect with a low-power indoor access point or subordinate device and never directly connects to other client devices. b) This device will always initiate transmission under the control of a low power indoor AP or subordinate except for brief transmissions before joining a network. These short messages will only occur if this client has detected an indoor AP or subordinate operating on a channel. These brief messages will have a time-out mechanism such that if it does not receive a response from an AP it will not continually repeat the request. c) All transmissions will be lower or equal to the power advertised by the indoor low-power access point or subordinate and never above the maximum output power allowed by the FCC grant for equipment class 6XD. d) This device employs a Contention-Based Protocol as demonstrated in the test report. e) We understand and acknowledge that this device is subject to the following restrictions, which are also documented within the user manual:

This device is prohibited for control of or communications with unmanned aircraft systems, including drones. If you should have any questions regarding this declaration, please do not hesitate to contact us, thank you!

Sincerely yours,

John Ramones, Head of Product Design NETGEAR, INC. Tel: 4088903160 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 3553 N. First St., San Jose, California 95134, United States Date: 2026-08-17 FCC ID: PY326200664 Declaration for DFS master devices We, NETGEAR, INC. hereby declare that this device meets all the other requirements specified in Part 15E Section 15.407. If you should have any question(s) regarding this declaration, please dont hesitate to contact us. Thank you!

John Ramones, Head of Product Design NETGEAR, INC. Tel: 4088903160 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 3553 N. First St., San Jose, California 95134, United States Date: 2026-08-14 FCC ID: PY326200664 To the attention of:

Federal Communications Commission Authorization and Evaluation Division Declaration Letter for Client Devices We, NETGEAR, INC., attest that this device under FCC ID: PY326200664 complies with device protocol requirements and operational restrictions for Client Devices. a) This device will only associate and connect with an indoor access point or subordinate device and never directly connects to other client devices. b) Client devices must be under control of an U-NII-4, Indoor access point or subordinate device. c) Clients shall passively scan to associate with access point or subordinate. d) Device may exist situations where the client may transmit brief messages, prior to being under the control of an AP, to join an AP network. But these brief messages will only occur if the client has detected a signal confirming that an AP is operating on a particular channel. These brief messages will have a time-out mechanism if it does not receive a response from an AP. e) Clients cannot have a direct connection to the internet to source the internet to other clients, access points, subordinates or clients from a wired or direct connection. f) We acknowledge this device is subject to and in full compliance with the device restrictions listed below. All users are notified of these restrictions through the user manual. A statement in a conspicuous location on the device and the user's manual: Section 15.19 Statement (if not on the device) If you should have any questions regarding this declaration, please do not hesitate to contact us, thank you!

Sincerely yours,

John Ramones, Head of Product Design NETGEAR, INC. Tel: 4088903160 Fax: 4089078097 E-mail: [email protected]

NETGEAR, INC. 3553 N. First St., San Jose, California 95134, United States Date: 2026-08-14 FCC ID: PY326200664 To the attention of:

Federal Communications Commission Authorization and Evaluation Division Declaration Letter for Indoor Access Points We, NETGEAR, INC., attest that this device under FCC ID: PY326200664 complies with the device protocol requirements and operational restrictions for Indoor Access Point Devices. a) This indoor access point can act as a master as defined in Section 15.202, allowing it to transmit without receiving an enabling signal. This mode can select a channel and initiate a network by sending enabling signals to client devices and subordinate devices. b) This Indoor Access Point operates in the 5.850-5.895 GHz band. Operation in this band is permitted only when the device is in plugged-in mode, as described in the user's manual. Before this band can be enabled through the device or web user interface, the end user must remove the battery and connect the device to a wall adapter. c) We acknowledge this device is subject to and in full compliance with the device restrictions listed below:

This device is for indoor use only. Indoor Access Points operating in the U-NII-4 band and U-NII -3 & -4 span channels shall be supplied power from a wired permanent indoor local power connection, use an integrated antenna, is not battery powered, and does not use a weatherized enclosure. This device bears the following statement in a conspicuous location on the device and the user's manual: FCC regulations restrict the operation of this device to indoor use only. If you should have any questions regarding this declaration, please do not hesitate to contact us, thank you!

Sincerely yours,

John Ramones, Head of Product Design NETGEAR, INC. Tel: 4088903160 Fax: 4089078097 E-mail: [email protected]

Compal Electronics Inc. Permission Letter July 30, 2026 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: Permission Letter (Module FCC ID: GKRRXLN4N, Date of Grant: 05/26/2026) To Whom It May Concern:

Being the Module applicant for the above mentioned FCC ID, We, Compal Electronics Inc., hereby authorize Netgear Inc. (Address: 3553 N. First St., San Jose, California 95134, USA) to transfer our test data in their test report for their Models: MR8400 under their own FCC ID: PY326200664. The module test results continue to be representative of and applicable to the equipment with the new FCC ID: PY326200664. Best Regards,

Print name: Shirley Liu Title: Certificate PM Tel: +886 2 8751-6228 Company name: Compal Electronics, Inc.