FCC ID: PY313400245 ProSAFE 802.11n Wall Mount Wireless Access Point

Installation Guide Punch down RJ45 connector Software license agreement Regulatory flyer Installation Guide ProSafe Wall Mount Access Point WN370 Package Contents Unpack the box and verify the contents:

ProSafe Wall Mount Access Point WN370 Mounting bracket with four mounting screws Warranty card Installation Requirements You must have the following items to successfully install your access point:

A 6mm Phillips screwdriver A T8 screwdriver A computer running Windows XP or Windows 7 A Standard EU or US wall outlet junction box with an ethernet cable routed through the wall from your LAN to the junction box An IEEE 802.3af/at compliant PoE switch or !EEE 802.3af/at compliant PoE injector Mount the Access Point The access point requires an electrical outlet junction box mounted in a wall. To mount the access point to the wall:

1. Remove the faceplate from the outlet junction box. 2. Run the Ethernet cable through the junction box with enough slack to reach the access point. 3. Run the Ethernet cables through the mounting bracket. 4. Align the mounting bracket with the holes on the junction box. 5. Attach the mounting bracket to the junction box using the included Phillips head screws. Note: If the Ethernet cable does not have a standard RJ45 connector, use the included RJ45 punch down connector to connect the Ethernet cable.

(Optional) Connect the Ethernet cable providing pass through support to the pass through port on the back of the access point. 7. 8. Mount the access point to the mounting bracket using the included T8 screws. 6. Connect the Ethernet cable providing PoE and network connectivity to the PoE port on the back of the access point. Set Up the Access Point The WN370 access point can only be deployed in a network managed by a ProSAFE WC7600 wireless controller. If you have a DHCP server in your network, option 43 must be enabled pointing towards the IP address of the WC7600. To discover and configure the access point using the WC7600 wireless controller:

1. Access the wireless controller at the network IP address that you configured. 2. Select Access Point > Discovery > Discovery Wizard. 3. Follow the steps onscreen to discover the access point and review the discovery results. 4. Select Access Point > Discovery > Managed AP List. Add the access points that you want to be managed by the wireless controller to the Managed AP List. Note: For extensive information about the Discovery Wizard and the discovery process, see the WC7600 reference manual. Verify Wireless Connectivity Using a computer with an 802.11b/g/n wireless adapter, verify connectivity by using a browser to connect to the Internet, or check for file and printer access on your network. You can also check the access point LEDs to verify a successful installation and connection. LED Power Description Solid amber. The access point is booting. Slow blinking amber. The access point is not managed by a wireless controller. Green.The access point has successfully booted and is managed by a wireless controller. NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to change without notice. NETGEAR, Inc. All rights reserved. For indoor use only. Valid in all EU member states, EFTA states, and Switzerland. December 2013 NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA 95134 USA LED Active WiFi On/Off Description Blinking Green. There is network traffic through the access point. Off. There is not network traffic through the access point. Solid Green. The access points WiFi is active. Off. The access points WiFi is off. Note: If you cannot connect, see Troubleshooting Tips in this guide. Troubleshooting Tips Here are some tips for correcting simple problems you might have. The WC7600 Cannot Discover or Manage the Access Point If the WC7600 cannot discover or manage the access point, you can log in to the access point to troubleshoot and download the system log. NETGEAR support will use the system log to help diagnose any problems with the access point. Note: The WN370 has DHCP enabled by default and receives an IP address if you have a DHCP server in your network. If you have a DHCP server in your network, use the address assigned to the WN370 to log in to the access point. To log in to the access point and download the system log:

1. Configure a computer with the following IP options:

IP address. 192.168.0.22 Subnet mask. 255.255.255.0 Default gateway. 192.168.0.1 2. Enter http://192.168.0.160 or your access points assigned IP address into a browser. 3. Log in to the access point using the following default credentials:

ID. admin Password. password. 4. Click Monitoring > Logs. 5. Click the Save As button. 6. Send the log to NETGEAR support. The Power LED is Solid Amber After Five Minutes There has been a boot up error and the access point needs to be reset. To reset the access point:

1. Remove the access point from the wall without disconnecting the Ethernet cable. 2. Press the reset button on the back of the access point for at least five seconds. 3. Mount the access point to the wall. 4. Follow the procedure for discovering the access point. Support Thank you for selecting NETGEAR products. After installing your device, locate the serial number on the label of your product and use it to register your product at https://my.netgear.com. You must register your product before you can use NETGEAR telephone support. NETGEAR recommends registering your product through the NETGEAR website. For product updates and web support, visit http://support.netgear.com. NETGEAR recommends that you use only the official NETGEAR support resources. For the current EU Declaration of Conformity, visit http://support.netgear.com/app/answers/detail/a_id/11621/. For regulatory compliance information, visit http://www.netgear.com/about/

regulatory/.

Notification of Compliance Regulatory Compliance Information This document includes user requirements for operating NETGEAR products in accordance with national laws including usage of radio spectrum and operation of radio devices. Failure of the end-user to comply with the applicable requirements may result in unlawful operation and adverse action against the end-user by the applicable national regulatory authority. The NETGEAR product firmware limits operation to only the channels allowed in a particular region or country. Therefore, all options described in this document may not be available in your version of the product. This document applies to both Class A and Class B devices:

Class A devices are intended to be used in a commercial or industrial environment. They are not intended to be used in a residential home or be available for general public use. Class B devices are intended to be used in a residential setting, and may also be used in commercial and industrial applications. Examples of Class B devices are telephones, personal computers, and residential data gateways. Europe EU Declaration of Conformity This section applies to products bearing the CE or CE! mark:

Products bearing the CE or CE! mark comply with the following EU directives:

EMC Directive 2004/108/EC Low Voltage Directive 2006/95/EC Ecodesign Directive 2009/125/EC RoHS Directive 2011/65/EU If the product has telecommunications functionality, it also complies with the requirement of the following EU directive:

R&TTE Directive 1999/5/EC Compliance with these directives implies conformity to harmonized European standards that are noted in the EU Declaration of Conformity. The EU CE Declaration of Conformity may be found at http://support.netgear.com/app/answers/detail/a_id/11621/. Caution for installing this equipment outdoors: (Valid in all EU member states, EFTA states, and Switzerland.) Be aware that outdoor installations require special attention and will only be handled by trained and qualified installation personnel. No one from the general public is permitted to install NETGEAR wireless products outdoors when external antennas, power and grounding must be installed for use. Particular attention has to be given allowed operational frequencies. Contact NETGEAR for instructions on how to contact an installer for outdoor operations if this product requires the special considerations for outdoor installations. For detailed information concerning installations in France, the user should contact the national spectrum authority in France (http://www.arcep.fr/ ) The following paragraphs apply to WN2500RP:

This device is a 2.4GHz and 5GHz wideband transmission system (transceiver), intended for indoor use only in all EU member states, EFTA states, and Switzerland. In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for aupplying public access to telecommunications and/or network services. This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10mW EIRP in the frequency range of 2454-2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. Warning NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference in which case the user may be required to take adequate measures. FCC Requirements for Operation in the United States Information in this section applies to products bearing the FCC mark (or statement):

FCC Information to User This NETGEAR product does not contain any user serviceable components and is to be used with approved antennas only. Any product changes or modifications will invalidate all applicable regulatory certifications and approvals. The following statement applies to these products:

EX6100 EX6200 VEGN2200 WN370 WN2500RP WN3000RPv2 WN3500RP This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. FCC Guidelines for Human Exposure This NETGEAR product complies with FCC radiation exposure limits set forth for an uncontrolled environment. The equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. FCC Declaration of Conformity We, NETGEAR, Inc., 350 East Plumeria Drive, San Jose, CA 95134, declare under our sole responsibility that this product complies with Part 15 Subpart B of FCC CFR47 Rules. Operation is subject to the following two conditions:

The device may not cause harmful interference, and The device must accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Warnings & Instructions The NETGEAR product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:

Reorient or relocate the receiving antenna. Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is Increase the separation between the equipment and the receiver. connected. Consult the dealer or an experienced radio/TV technician for help. FCC RF Radiation Exposure and SAR Statements The information in this section applies to products that transmit data or communicate wirelessly. SAR Statement The information in this section applies to NETGEAR wireless products that are intended to be operated close to human body. NETGEAR products that are intended to be operated close to the human body are tested for body-worn Specific Absorption Rate (SAR) compliance. The SAR limit set by the FCC is 1.6 W/kg. The FCC has established detailed SAR requirements and NETGEAR products meet these requirements. NETGEAR USB products were tested while installed in a host notebook computer. RF Exposure Information NETGEAR products have been evaluated under FCC Bulletin OET 65C (01-01) and found to be compliant to the requirements as set forth in CFR 47 Sections, 2.1093, and 15.247 (b) (4) addressing RF exposure from radio frequency devices. NETGEAR products meet the applicable government requirements for exposure to radio frequency waves. To see the test results reporting the highest SAR level measured for this device, visit http://www.netgear.com/about/regulatory/declarations-conformity/

Radiation exposure: NETGEAR products comply with radiation exposure limits set forth for an uncontrolled environment and meet radio frequency (RF) exposure guidelines for wireless routers. NETGEAR products should be installed and operated keeping the product 20cm or more away from a persons body. For devices that are battery powered and may be operated closer than 20cm to you, refer to the NETGEAR website for exposure levels. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. NETGEAR products comply with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) NETGEAR products may not cause harmful interference, and (2) NETGEAR products must accept any interference received, including interference that may cause undesired operation. For products available in the USA market, only channel 1~11 can be operated. Selection of other channels is not possible. The following statement applies to these products:

EX6100 EX6200 VEGN2200 WN370 WN2500RP WN3000RPv2 WN3500RP The device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. The following statement applies to these products:

EX6100 EX6200 VEGN2200 WN2500RP The device operates in 5.15~5/25GHz frequency range. It is restricted in indoor environment only. Non-DFS Warning NETGEAR non-DFS products do not support operation in the 5600-5650MHz band. The firmware on the device restricts the operation in this frequency band and does not utilize the channels in this band. NETGEAR non-DFS products will not permit operations on channels 120132 for 11a and 11n/a, which overlap the 56005650MHz band. Country Code Selection Usage (WLAN devices) The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. TV Tuner (on Selected Models) The information in this section applies to NETGEAR products incorporating a TV tuner. Note to CATV System Installer: This reminder is provided to call the CATV system installers attention to Section 820-

93 of the National Electrical Code, which provides guidelines for proper grounding and, in particular, specifies that the Coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as possible. Canadian Department of Communications Radio Interference Regulations The information in this section applies to products bearing the statements:. This digital apparatus does not exceed the Class B limits for radio-noise emissions from digital apparatus as set out in the Radio Interference Regulations of the Canadian Department of Communications. Cet appareil numrique ne dpasse pas les limites de la classe B pour les missions radio bruit des appareils numriques, tel qu'nonc dans le Rglement sur le brouillage radiolectrique du ministre des Communications du Canada. CAN ICES-3 (B)/NMB-3(B) CAN ICES-3 (A)/NMB-3(A) Industry Canada NETGEAR products comply with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) NETGEAR products may not cause harmful interference, and (2) NETGEAR products must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme la norme CNR d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage prjudiciable, et (2) ce dispositif doit accepter tout brouillage reu, y compris un brouillage susceptible de provoquer un fonctionnement indsirable. IMPORTANT NOTE: Radiation Exposure Statement NETGEAR products comply with IC radiation exposure limits set forth for an uncontrolled environment. NETGEAR products should be installed and operated with minimum distance 20cm between the radiator and your body. For products available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. The following statement applies to these products:

EX6100 EX6200 VEGN2200 WN370 WN2500RP WN3000RPv2 The device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with IC multi-transmitter product procedures. The following statement applies to these products:

EX6100 EX6200 VEGN2200 WN2500RP The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-

channel mobile satellite systems. NOTE IMPORTANTE: Dclaration d'exposition aux radiations Pour les appareils qui transmettent des donnes sans fil: Cet quipement est conforme aux limites d'exposition aux rayonnements IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. Pour les produits disponibles aux tats-Unis / Canada du march, seul le canal 1 11 peuvent tre exploits. Slection d'autres canaux n'est pas possible. La dclaration suivante s'applique ces produits:

EX6100 EX6200 VEGN2200 WN370 WN2500RP WN3000RPv2 Cet appareil et son antenne (s) ne doit pas tre co-localiss ou fonctionnement en association avec une autre antenne ou transmetteur. La dclaration suivante s'applique ces produits:

EX6100 EX6200 VEGN2200 WN2500RP les dispositifs fonctionnant dans la bande 5150-5250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux. Interference Reduction Table The table below shows the Recommended Minimum Distance between NETGEAR equipment and household appliances to reduce interference (in feet and meters). Household Appliance Microwave oven Baby monitor analog Baby monitor digital Cordless phone analog Cordless phone digital Bluetooth device ZigBee Recommended Minimum Distance (in feet and meters) 30 feet / 9 meters 20 feet / 6 meters 40 feet / 12 meters 20 feet / 6 meters 30 feet / 9 meters 20 feet / 6 meters 20 feet / 6 meters Japan Notices VCCI This information in this section applies to products bearing the VCCI mark:

Class A ITE A Class B ITE B Japan Wireless Notice South Korea Notices The information in this section applies to products bearing the KCC mark:

Class A :

A

( ) Class B :

B

(A)

(B)

, . Taiwan WWAN Wireless Notice The information in this section applies to products bearing the Taiwan National Communications Commission mark:

This telecom equipment has complied with NCC regulations. 5.25-5.35 Thailand Notice The information in this section applies to products approved by the Thailand National Communications Commission:

. China Notices The information in this section applies to products bearing the Chinese Complusory Certification Mark:

This device complies with the requirements in China for Safety and Quality A Australia and New Zealand Notices The information in this section applies to products bearing the Australia C-Tick and A-Tick Compulsory Marks:

This device equipment complies with the Australian and New Zealand regulatory approvals requirements. Warning NETGEAR Class A products that may be utilized in domestic/residential environments may cause radio interference in which case the user may be required to take adequate measures. Powerline Device Safety Information Follow these safety guidelines to ensure your own personal safety and to help protect your system from potential damage:

For national approvals (approval schemes other than CB), relevant national standards for plug, socket-

outlet, and direct plug-in units (for example, US) shall also be consulted while testing and approving such products according to the national standards. Check the electrical current for any device plugged into the filtered AC socket. Do not exceed home and product outlet ratings and electrical requirements. The socket-outlet shall be installed near the equipment and be easily accessible Only power cords and allowed to be inserted into the filtered AC socket; no other equipment with a direct plug-in is allowed. Power cords needs to be a maximum of 1m long and a minimum of 0.75mm of cross-

sectional area. Do not plug devices into the Powerline Pass Thru Adapter filtered AC outlet that exceed the product ratings. The output voltage of the filtered AC outlet is the same as the power outlet that the Powerline Pass Thru Adapter is plugged into. To help avoid damaging your system, be sure that the attached devices are electrically rated to operate with the power available in your location. If the input AC voltage is less than 100 Vac, the device plugged into the filtered AC socket of the Powerline Pass Thru Adapter might not perform as well as expected. DO NOT PLUG MAJOR HOME APPLIANCES into the filtered AC socket or into an attached power strip. The device is not intended to be used with home appliances such as air conditioners, power tools, space heaters, fans hair dryers, ovens, or refrigerators. Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Do not service any product except as explained in your system documentation. Opening or removing covers that are marked with the triangular symbol with a lightning bolt can expose you to electrical shock. Only a trained service technician should service components inside these compartments. Use the product only with approved equipment. Allow the products to cool before removing covers or touching internal components. To help avoid damaging your system, be sure that the voltage selection switch (if provided) on the power supply is set o match the power available at your location:

o o o 110 volts (V), 60 hertz (Hz) in most of North and South America and some Far Eastern countries such as south Korea and Taiwan 100, 50 Hz in eastern Japan and 100, 60Hz in western Japan 230v, 50Hz in most of Europe, the Middle East, and the Far East The peripheral power cables are equipped with three-prong plugs to help ensure proper grounding. Do not use adapter plugs or remove the grounding prong from a cable. Observe extension cable and power strip ratings. Make sure that the total ampere rating of all products plugged into the extension cable or power strip does not exceed 80 percent of the ampere ratings limit for te extension cable or power strip. To help protect your system from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS). Rack Mount Safety Instructions This information applies to the installation of all NETGEAR rack mount products Ambient operating temperature. If the switch is installed in a closed or multiunit rack assembly, the ambient operating temperature of the rack environment might be greater than the ambient temperature of the room. Therefore, consider installing the equipment in an environment compatible with the maximum rated ambient temperature. Reduced airflow. Mount the equipment into a rack so that the amount of airflow required for safe operation is not compromised. Mechanical loading. Mount the equipment into a rack so that a hazardous condition does not arise due to uneven mechanical loading. Circuit overloading. Consider the equipments connection to the power supply circuitry and the effect that any possible overloading of circuits might have on overcurrent protection and power supply wiring. Consider equipment nameplate ratings when addressing this concern. Reliable grounding. This product requires reliable grounding to be maintained at all times. To ensure this, ground the rack itself. Pay particular attention to power supply connections other than the direct connections to the branch circuit (for example, the use of power strips). Clearance. Leave enough clearance in front of the rack (about 25 inches) to enable you to open the front door completely and in the back of the rack (about 30 inches) to allow for sufficient airflow and ease in servicing. NETGEAR, Inc., 350 E. Plumeria Avenue, San Jose, CA 95134 USA December 2013