FCC ID: PY307300072 RangeMax Duo Wireless-N Router

Wireless Router Setup Manual NETGEAR, Inc. 4500 Great America Parkway Santa Clara, CA 95054 USA November 2007 208-10148-01 v1.0 Trademarks NETGEAR and the NETGEAR logo are registered trademarks, and RangeMax and Smart Wizard are trademarks of NETGEAR. Inc. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Other brand and product names are registered trademarks or trademarks of their respective holders. Statement of Conditions In the interest of improving internal design, operational function, and/or reliability, NETGEAR reserves the right to make changes to the products described in this document without notice. NETGEAR does not assume any liability that may occur due to the use or application of the product(s) or circuit layout(s) described herein. 2007 by NETGEAR, Inc. All rights reserved. ii Contents Getting to Know Your Wireless Router ................................................................................1 Unpacking Your New Wireless Router ...............................................................................1 What You Need Before You Begin .....................................................................................8 Updating Your Router Firmware ........................................................................................9 Two Setup Methods: Smart Wizard Setup or Manual Setup .............................................9 Smart Wizard Setup ..........................................................................................................9 Manual Setup ..................................................................................................................10 Product Registration, Support, and Documentation ........................................................15 Accessing the Wireless Router after Installation and Checking for New Firmware .........16 Setting Up and Testing Basic Wireless Connectivity .......................................................18 Implementing Appropriate Wireless Security ...................................................................20 Help with Troubleshooting..................................................................................................21 Basic Troubleshooting .....................................................................................................21 Troubleshooting Connectivity Using the Ping Utility ........................................................26 Default Configuration ..........................................................................................................29 Default Configuration Settings .........................................................................................29 Restoring the Default Password and Configuration Settings ...........................................32 Related Documents..............................................................................................................33 Contents iii iv Contents Getting to Know Your Wireless Router Congratulations on your purchase of the NETGEAR RangeMax Dual Band Wireless-N Router WNDR3300. Before you begin installing your router, check the package contents (see Unpacking Your New Wireless Router). Become familiar with the front and back panels of your routerespecially the status lightsand the important information on the router label (see Bottom Label on page 8). The wireless router Unpacking Your New Wireless Router The product package should contain the following items:

A snap-on stand for your wireless router An AC power adapter (varies by region) A yellow Ethernet cable The Resource CD, which includes:

The Smart Wizard Installation Assistant (Autorun.exe) A PDF version of this manual A link to the online Reference Manual Warranty and Support Information cards If any of the parts are incorrect, missing, or damaged, contact your NETGEAR dealer. Keep the carton, including the original packing materials, in case you need to return the product for repair. To prepare your router for installation:

1. Carefully peel off the protective film covering the sides of your router. Getting to Know Your Wireless Router 1 v1.0, November 2007 Wireless Router Setup Manual 2. Set up your wireless router by inserting the router into the stand supplied with your router. Figure 1 3. Place your router in an area suitable for installation (near an AC power outlet and accessible to the Ethernet cables for your wired computers). 2 Getting to Know Your Wireless Router v1.0, November 2007 Router Front Panel Wireless Router Setup Manual Figure 2 You can use the status lights on the front of the wireless router to verify various conditions. Table 1. Status Light Descriptions Item Function Activity 1 Power On green solid Blinking 2 3 2.4 GHz Mode 5 GHz Mode Off On ambera On greenb Blinking On bluec Off Blinking Description Power is supplied to the router. The unit is starting up, or the restore factory settings button is being pushed to restore the factory default settings. Power is not supplied to the router. The unit is operating in Legacy G mode at 2.4 GHz

(5 GHz Mode [item 3] is also on). The unit is operating in 11n mode at 2.4 GHz

(5 GHz Mode [item 3] is off). Data is being communicated over the wireless network. The unit is operating in 11n mode at 5 GHz

(2.4 GHz Mode [item 2] is also on, amber). 11n mode at 5 GHz is off

(2.4 GHz Mode [item 2] is on, green). Data is being communicated over the wireless network. Getting to Know Your Wireless Router 3 v1.0, November 2007 Wireless Router Setup Manual Table 1. Status Light Descriptions (continued) Internet Amber off Amber on Amber blinking Item Function Activity 4 Description No Ethernet cable is connected to the modem. The Ethernet cable connection to the modem is good. Packets are being transmitted and received from a modem or other network device, but no IP address has been received. No IP address has been received. IP address has been received. IP address has been received, and data is being transmitted and received. The LAN port has detected a 100 Mbps link with an attached device. The LAN port has detected a 10 Mbps link with an attached device. a. On amber (default setting) signifies a 5 GHz interference-free Wireless-N and legacy 2.4 GHz 802.11g network. NETGEAR recommends this if you have Dual Band clients (Dual Band Wireless-N laptops, Dual Band Wireless-N adapters) and/or 802.11 b/g laptops to connect. Green off On Blinking Green Amber LAN 5 b. On green signifies a 2.4 GHz Wireless-N network. NETGEAR recommends this if you have only 2.4 GHz Wireless-N clients

(most adapters are 2.4 GHz, if not specified as Dual Band) AND/OR 802.11 b/g laptops to connect. c. On blue signifies a 5 GHz interference-free nework. For more information on modes, see To change modes if you notice interference: on page 19, and the online Reference Manual, available on the Resource CD. 4 Getting to Know Your Wireless Router v1.0, November 2007 Router Back Panel The rear panel of the WNDR3300 router contains the items in the list that follows the figure. Wireless Router Setup Manual 1 2 3 4 Figure 3 The back of the wireless router includes:

1. Four local (LAN) 10/100 Mbps Ethernet ports for connecting the router to local computers 2. 3. Restore factory settings button 4. AC power adapter outlet Internet (WAN) Ethernet port for connecting the router to a cable or DSL modem Getting to Know Your Wireless Router 5 v1.0, November 2007 Wireless Router Setup Manual Top Panel Figure 4 The top of the wireless router includes a dome that performs two functions:

1. Antenna display lights. The lights identify the activity of the eight internal antennas, flashing to show which combination of antennas is receiving the strongest signals. These status lights are off by default but can be turned on. To turn the antenna display lights on or off:

a. Push the dome for less than 2 seconds, then release. If lights are off, they will turn on. b. Push the dome for less than 2 seconds, then release. If lights are on, they will turn off. 2. Wi-Fi Protected Setup (WPS). The dome acts as a push-button for the router to enable WPS security with other WPS-enabled devices. Pushing on the dome for over 5 seconds opens a 2-

minute window for the router to connect with other WPS-enabled devices. Before using these WiFi Protected Setup (WPS) push-button procedures, verify that your device (a notebook, adapter, or other device) supports WPS. If you do not have any other WPS-enabled devices, there is no need to open the 2 minute period when security will be disabled, or to configure your router security for WPS. To connect to another device using WPS:

a. Open the networking utility of the device that supports WiFi Protected Setup (WPS) and follow the utilitys instructions for when to proceed to step b. 6 Getting to Know Your Wireless Router v1.0, November 2007 b. Push the wireless routers dome for 5 seconds, then release. The dome lights should begin to blink. Wireless Router Setup Manual While the router is in WPS enable mode (a maximum of 2 minutes), wireless security is not enabled. Indoors, computers can connect over wireless networks at a range of several hundred feet. Unlike wired network data, your wireless data transmissions can extend beyond your walls, and anyone with a compatible adapter can receive them, allowing others outside your immediate area to access your network. For more information about security, see the Reference Manual that is available from a link on the Resource CD as well as a link in the main menu of your router. c. While the dome lights are blinking, you have 2 minutes to enable WPS on the device you are trying to connect with the router. The blinking ceases when one of these two conditions occurs:

WPS is enabled between the router and the other device you are connecting to. The 2-minute window period expires for establishing a WPS connection. Whether or not a connection is established, your router security and SSID (service set identification key) are now configured for WPS. d. e. The lights return to off or antenna display, depending on how you have set them. If after enabling WPS you need to connect a device that does not include WPS functionality, you will need to first log in to the router and obtain the security key. For more information, refer to Accessing the Wireless Router after Installation and Checking for New Firmware on page 16, and the online Reference Manual, available as a link on the Resource CD. If you want to disable WPS, you have to reset your router to factory default settings. For information about resetting to the default settings, see Restoring the Default Password and Configuration Settings on page 32. Getting to Know Your Wireless Router 7 v1.0, November 2007 Wireless Router Setup Manual Bottom Label View the label on the bottom of the wireless router to identify the serial number, port connectors, status lights, and default login information. Figure 5 What You Need Before You Begin Prepare the following before you set up your router:

Internet login name and password (frequently an e-mail address and password) Internet service. The configuration information your Internet Service Provider (ISP) gave you. Depending on how your Internet account was set up, you might need one or more of these settings for the wireless router to access the Internet:

Host and domain names Domain Name Server (DNS) addresses Your ISP should have provided you with all the information needed to connect to the Internet. If you cannot locate this information, you can ask your ISP to provide it. For cable modem service, use the computer you first used to set up your Internet service. Fixed or static IP address 8 Getting to Know Your Wireless Router v1.0, November 2007 Wireless Router Setup Manual Updating Your Router Firmware NETGEAR is always improving the operability and features included with your router. To make it easy for you to receive the best, most up-to-date features of your router, NETGEAR provides a variety of methods for updating your product. The Smart Wizard installation assistant lets you check for and install updates as part of the setup activity. The router includes an update feature that lets you check for and install updates. You must be logged in to the router to use this feature. These options are discussed in Accessing the Wireless Router after Installation and Checking for New Firmware on page 16. Two Setup Methods: Smart Wizard Setup or Manual Setup You have two methods available for setting up your wireless router:

Smart Wizard setup. This option is the easiest. The wizard guides you through the setup process, automates many of the steps, and verifies that necessary conditions exist and that steps you perform have been successfully completed. This option requires a PC running Microsoft Windows. Manual setup. This option is best if you cannot use the wizard on the CD, are replacing an existing wireless router, or are technically knowledgeable. Follow the instructions in this manual to set up your wireless router. Use the setup option that best suits you. Smart Wizard Setup The wizard setup process takes about 20 minutes to complete. 1. Insert the NETGEAR CD into a Windows PC. The CD automatically starts and detects the language that you are using on your PC. Accept the language option, or change to a different language. If the CD does not automatically start, browse the CD and double-click Autorun. Be sure to double-click the Autorun file that begins with an uppercase A. Getting to Know Your Wireless Router 9 v1.0, November 2007 Wireless Router Setup Manual 2. When the Welcome screen displays, click Setup to start the Smart Wizard. Follow the wizard instructions. 3. When you are asked to log in, refer to the bottom label for the default login information, or see the steps in Connecting Your Wireless Router. Manual Setup There are two steps to setting up your wireless router:

1. Connect the router to the ADSL or cable modem, and connect a computer to the router. Your computer has to be set to automatically get its TCP/IP network settings from the router through DHCP. This is usually the case. If you are unsure about this, use the wizard on the CD, which automatically takes care of this for you, or refer to the documentation for your computer. 2. Configure the router to use your Internet service. Connecting Your Wireless Router To connect your wireless router:

1. Connect the wireless router, the computer, and the modem. a. Turn off your computer. b. Turn off and unplug the cable or ADSL broadband modem. 10 Getting to Know Your Wireless Router v1.0, November 2007 Wireless Router Setup Manual c. Locate the Ethernet cable (1) that connects your computer to the modem. 1 2 Figure 6 d. Disconnect the cable at the modem (2). You will connect it to the router later. e. Use the label on the bottom of the wireless router to locate the Internet port, which is on the left next to the power connection. f. Locate the Ethernet cable that came with the NETGEAR product. Securely insert that Ethernet cable into your modem and into the Internet port of the wireless router (3). 3 Internet Figure 7 Getting to Know Your Wireless Router 11 v1.0, November 2007 Wireless Router Setup Manual g. Locate the cable you removed from the modem in step 1c. Securely insert that cable (4) into a LAN port on the router such as LAN port 1. 4 Internet Figure 8 Your network cables are connected, and you are ready to start your network. 2. Start your network in the correct sequence. Failure to start or restart your network in the correct sequence could prevent you from accessing the Internet. a. First, plug in and turn on the cable or DSL modem. Wait 2 minutes. b. Now, plug the power cord into your wireless router and into a power outlet. Wait 1 minute. c. Last, turn on your computer. For DSL customers, if software logs you in to the Internet, do not run that software. You might need to go to the Internet Explorer Tools menu, select Internet Options, and then click the Connections tab, where you can select Never dial a connection. 12 Getting to Know Your Wireless Router v1.0, November 2007 Wireless Router Setup Manual Figure 9 d. Check the wireless router status lights to verify the following:

Power. The Power light (1) should turn solid green. If it does not, see Basic Functions Are Not Working on page 22. Mode. The Mode light (2) should be on: the Mode light (3) should be off. Internet. The Internet port light (4) should be lit. If it is not, make sure that the Ethernet cable is securely attached to the wireless router Internet port and that the modem, and that the modem is powered on. LAN. A LAN light (5) should be lit. Green indicates that your computer is communicating at 100 Mbps; amber indicates 10 Mbps. If a LAN light is not lit, check that the Ethernet cable from the computer to the router is securely attached at both ends, and that the computer is turned on. 3. Connect to the wireless router by typing http://www.routerlogin.net in the address field of your browser, and then press Enter. Figure 10 Connect to the wireless router by typing any one of these three URLs in the address field of your browser, then pressing Enter:

http://www.routerlogin.net http://www.routerlogin.com http://192.168.1.1 Getting to Know Your Wireless Router 13 v1.0, November 2007 Wireless Router Setup Manual A login window like the one in the following figure opens:

Figure 11 4. For security reasons, the router has its own user name and password. When prompted, enter admin for the router user name and password for the router password, both in lowercase letters. The router user name and password are not the same as any other user name or password you might use to log in to your Internet connection. After logging in, if you see a window with a message about firmware upgrades, click Close Window. 14 Getting to Know Your Wireless Router v1.0, November 2007 On the left, click Setup Wizard to view the following screen. Wireless Router Setup Manual Figure 12 If you cannot connect to the wireless router, verify your computer networking setup. It should be set to obtain both IP and DNS server addresses automatically, which is usually the case. For help with this, consult the documentation that came with your computer, or see the links in Related Documents on page 33. 5. Click Next. The wizard assists you with configuring your wireless router to access the Internet. Advanced users who want to manually configure the router can select the No radio button, enter admin and password as the user name and password when prompted, and fill in the required information on the Basic Settings screen (for more information about basic settings, refer to the Reference Manual, available as a link on the Resource CD). 6. Click Done to finish. You are now connected to the Internet! The wireless router displays its home page. If you do not click Logout, the wireless router waits 5 minutes after there is no activity before it automatically logs you out. Product Registration, Support, and Documentation Register your product at http://www.NETGEAR.com/register. Registration is required before you can use NETGEARs telephone support service. Product updates and Web support are always available by going to http://www.NETGEAR.com/support. Documentation is available on the CD, on the support website, and on the documentation website. When the wireless router is connected to the Internet, click the Knowledge Base or the Getting to Know Your Wireless Router 15 v1.0, November 2007 Wireless Router Setup Manual Documentation link under Web Support to view support information or the documentation for the wireless router. Accessing the Wireless Router after Installation and Checking for New Firmware The Smart Wizard appears only when you first install the router or when the router is in its factory default state (for example, if you have reset the router to its factory default settings). If you want to change the settings after installing and configuring your router using the Smart Wizard, you must open a browser window and log in to the router. The factory default state is restored when you use the restore factory settings button. See Restoring the Default Password and Configuration Settings on page 32 for more information about this feature. To access the router using its login name and password:

1. Connect to the wireless router by typing http://www.routerlogin.net in the address field of your browser, and then press Enter. Figure 13 You can connect to the wireless router by typing any one of these three URLs in the address field of your browser, then pressing Enter:

http://www.routerlogin.net http://www.routerlogin.com http://192.168.1.1 2. For security reasons, the router has its own user name and password. When prompted, enter admin for the router user name and password for the router password, both in lowercase letters. The router user name and password are not the same as any other user name or password you might use to log in to your Internet connection. 16 Getting to Know Your Wireless Router v1.0, November 2007 A login window like the one in the following figure opens:

Wireless Router Setup Manual Figure 14 Enter the user name and password. To update your router firmware:

1. If the Router Upgrade screen does not display automatically, select Router Upgrade under Maintenance on the main menu. The Router Upgrade screen displays. 2. Click Browse, and locate the unzipped firmware image that you downloaded to your PC (the file ends in .chk). 3. Once you have selected the file, click Upload to send the software to the router. The upload process takes several minutes. When the software upload process is complete, the router restarts. Do not try to go online, turn off the router, shut down the computer, or do anything else to the router until the router finishes restarting! When the Power light stops blinking, wait a few seconds more before using the router. 4. After the router has restarted, select Router Status under Maintenance on the main menu. Check the firmware version to verify that your router now has the new software installed. Getting to Know Your Wireless Router 17 v1.0, November 2007 Wireless Router Setup Manual If you are unable to successfully upgrade using this method, refer to the online Reference Manual available through the Documentation link on the router main menu (or through a link on the Resource CD) for other ways to upgrade the router. If you selected the No radio button during installation, and you want to check for new firmware later, use the following procedure. Determine the firmware version currently running on your router before you check for updates on the NETGEAR website. Then go to the NETGEAR website and select the model number for this router. If a later version of the firmware is available, upload the firmware to your computer, and upgrade your router. To manually check for new router firmware:

1. Open a browser window, and type http://www.routerlogin.net in the address field of your browser. Press Enter. 2. When prompted, enter the default user name and password (admin for the router user name and password for the router password), both in lowercase letters. If you changed the user name and password from the defaults, then enter your new user name and password. 3. Select Router Status under Maintenance on the router main menu. When the Router Status screen displays, note the version number of your router firmware. 4. Go to http://www.NETGEAR.com/support, and select Downloads from the menu bar. 5. From the Product Selection drop-down list, select your router model number. The Product Support page for your router displays. 6. Under Downloads, check the most recent firmware version offered against the firmware version shown on the Router Status screen. If the version on the NETGEAR website is more recent, click its version number, then click Right-click and Save to Download, and save the file to a location on your hard disk. 8. Follow the procedure in To update your router firmware: on page 17 to complete the 7. upgrade process. Setting Up and Testing Basic Wireless Connectivity Follow these instructions to set up and test basic wireless connectivity, or change operating mode. Once you have established basic wireless connectivity, you can enable security settings appropriate to your needs. 18 Getting to Know Your Wireless Router v1.0, November 2007 Wireless Router Setup Manual To set up and test basic wireless connectivity:

1. Log in to the wireless router at its default LAN address of http://192.168.1.1 with the default user name of admin and default password of password, or using whatever LAN address and password you have set up. 2. Select Wireless Settings under Setup in the main menu. 3. Note that the default SSID (service set identification key) is NETGEAR. The SSID of any wireless adapters must match the SSID you configure in the wireless router. If they do not match, you will not get a wireless connection. 4. Select the region in which the wireless interface will operate. 5. To save your changes, click Apply. If you are configuring the router from a wireless computer and you change the routers SSID, channel, or security settings, you will lose your wireless connection when you click Apply. You must then change the wireless settings of your computer to match the routers new settings. 6. Configure and test your computers for wireless connectivity. Program the wireless adapter of your computers to have the same wireless network name

(SSID) as the wireless router. Check that they have a wireless link and are able to obtain an IP address by DHCP from the router. To change modes if you notice interference:

You might notice interference from nearby devices, such as another router. By default, your WNDR3300 router is set to: Up to 270Mbps at 5GHz & 54Mbps at 2.4GHz, which provides the best operation for most situations. There are 4 wireless mode combinations available for the WNDR3300 router. To select another mode that might improve your wireless communications, do the following:

1. Log in to the wireless router at its default LAN address of http://192.168.1.1 with the default user name of admin and default password of password, or using whatever LAN address and password you have set up. 2. Select Wireless Settings under Setup in the main menu. 3. Select a wireless mode:

Getting to Know Your Wireless Router 19 v1.0, November 2007 Wireless Router Setup Manual Up to 270Mbps at 5GHz & 54Mbps at 2.4GHz (default setting) Up to 270Mbps at 2.4GHz Up to 130Mbps at 2.4GHz Up to 130Mbps at 5GHz & 54Mbps at 2.4GHz 4. To save your changes, click Apply. Implementing Appropriate Wireless Security Indoors, computers can connect over 802.11g wireless networks at a range of over 300 feet. Such distances can allow others outside your immediate area to access your network. Unlike wired network data, your wireless data transmissions can extend beyond your walls and can be received by anyone with a compatible adapter. For this reason, use the security features of your wireless equipment. The wireless router provides highly effective security features, which are covered in detail in the Reference Manual that is available from a link on the Resource CD as well as a link in the main menu of your router. Follow the instructions in this manual and in the router help screens to implement the security features appropriate to your needs. For more information on wireless security, refer to To connect to another device using WPS: on page 6 and the online Reference Manual, available as a link on the Resource CD. 20 Getting to Know Your Wireless Router v1.0, November 2007 Help with Troubleshooting This chapter gives information about troubleshooting your wireless router. You can find help with the following problems:

Common Things That Can Go Wrong Basic Functions Are Not Working on page 22 I Am Unable to Log In to the Wireless Router on page 23 The Internet Service Connection Is Not Working on page 23 Testing the Path from a PC to Your Router on page 26 Testing the Path from a PC to the Internet on page 27 Basic Troubleshooting Here are some tips for correcting simple problems you might have. Common Things That Can Go Wrong Verify that you do not have these common problems. Be sure to always start your network in this sequence:

1. Turn off and unplug the modem from its power outlet, and turn off the wireless router and computer. 2. Turn on the modem, and wait 2 minutes. 3. Turn on the wireless router, and wait 1 minute. 4. Turn on the computer. Make sure that the Ethernet cables are securely plugged in:

1. Verify that the Internet status light on the wireless router is lit if the Ethernet cable to the wireless router from the modem is plugged in securely and the modem and wireless router are both turned on (see Router Front Panel on page 3). Help with Troubleshooting 21 v1.0, November 2007 Wireless Router Setup Manual 2. Verify that for each powered-on computer connected to the wireless router with a securely plugged in Ethernet cable, the corresponding wireless router LAN port status light is lit (see Router Front Panel on page 3). The label on the bottom of the wireless router identifies the number of each LAN port (see Bottom Label on page 8). Make sure that the network settings of the computer are correct:

1. Verify that your LAN-connected computers are configured to obtain an IP address automatically through DHCP. For help with this, see the documentation for your computer or Related Documents on page 33. 2. Verify whether the MAC address is needed. Some cable modem services require you to use the MAC address of the computer registered on the account. If this is the case, in the Router MAC Address section of the Basic Settings screen, select Use this Computers MAC Address. To save your settings, click Apply. Restart the network in the correct sequence. Check the router status lights to verify correct router operation:

If the Power light does not turn solid green within 2 minutes after you turn the router on, reset the router according to the instructions in Restoring the Default Password and Configuration Settings on page 32. Basic Functions Are Not Working After you turn on power to the router, check these status lights:

1. When power is first applied, verify that the Power light blinks and then turns solid green. a. Make sure that the power cord is properly connected to your router and that the power supply adapter is properly connected to a functioning power outlet. b. Check that you are using the power adapter supplied by NETGEAR for this product. If the error persists, you have a hardware problem and should contact Technical Support. 2. After approximately 20 seconds, verify the following:

a. The appropriate Mode light is lit (the 2.4 GHz mode is the default). b. The Internet port is connected and its light is lit. c. The LAN port lights are lit for any local ports that are connected. 22 Help with Troubleshooting v1.0, November 2007 Wireless Router Setup Manual If a ports light is lit, a link has been established to the connected device. If a LAN port is connected to a 100 Mbps device, verify that the ports light is green. If the port is 10 Mbps, the light is amber. For more information about the status lights, see Router Front Panel on page 3. If the LAN or Internet port lights are not on when the Ethernet connection is made:

1. Make sure that the Ethernet cable connections are secure at the router and at the computer. 2. Make sure that power is turned on to the connected computer. 3. Make sure that you are using Ethernet cables like the cable that was supplied with the wireless router. I Am Unable to Log In to the Wireless Router If you are unable to log in to the wireless router, check the following:

If you are using an Ethernet-connected computer, check the Ethernet connection between the computer and the router as described in the previous section. Make sure that you are using the correct login information. The factory default login name is admin, and the password is password. Make sure that Caps Lock is off when you enter this information. Typically, your computers address should be in the range of 255.255.255.0.2 to 255.255.255.0.254. Refer to your computers documentation for help with finding your computers IP address. If your computers IP address is 169.254.x.x, verify that you have a good connection from the computer to the router, and then restart your computer. Make sure that your browser has Java, JavaScript, or ActiveX enabled. If you are using Internet Explorer, click Refresh to be sure that the Java applet is loaded. Try closing the browser and starting it again. The Internet Service Connection Is Not Working If your router is unable to access the Internet, check that the Internet connection is working, and then check that the wireless router can get an Internet address. Help with Troubleshooting 23 v1.0, November 2007 Wireless Router Setup Manual Check that the Internet connection is working:

1. Internet connection. First verify that your cable or ADSL modem has a successful connection. The cable or ADSL modem status lights indicate if the modem connection is successful or not. Check your modem documentation, or call your Internet Service Provider for help with verifying that the modem has a successful connection. 2. Wireless router Internet light is green or blinking green. If your Internet light is green or blinking green, then you have a good Internet connection, and your wiring is correct. 3. Wireless router Internet light blinking amber. If your Internet light is blinking amber, then your wireless router is attempting to make an Internet connection with the service provider. The light should turn green within several minutes. If it does not, check the Internet connection on the modem. 4. Wireless router Internet light off. If the Internet light is off, verify that the Ethernet cable is securely connected between the cable or ADSL modem, and that both the modem and wireless router are turned on. Obtaining an Internet IP Address If your wireless router is unable to access the Internet, and your Internet light is amber or blinking amber, check the wireless router to see if it is able to get an Internet IP address from your service provider. Unless you have a static IP address, your wireless router automatically requests an IP address from your service provider. To check the Internet IP address from the browser interface:

1. Log in to the wireless router. 2. Select Router Status under Maintenance on the main menu to check that an IP address is shown for the Internet port. If 0.0.0.0 is shown, your wireless router has not obtained an IP address from your service provider. If your router is unable to obtain an IP address from the your service provider, the problem might be one of the following:

Your service provider might require a login. Ask your service provider whether they require PPP over Ethernet (PPPoE) login. The service name, user name, and password might be set incorrectly. See Troubleshooting PPPoE. Your service provider might check for your computers host name. Assign the computer host name of your ISP account to the wireless router in the Basic Settings screen. 24 Help with Troubleshooting v1.0, November 2007 Wireless Router Setup Manual Your service provider allows only one Ethernet MAC address to connect to Internet, and might check for your computers MAC address. In this case, do one of the following:

Inform your service provider that you have bought a new network device, and ask them to use the wireless routers MAC address. Configure your router to spoof your computers MAC address. This can be done in the Basic Settings screen. Refer to the online help, which you can access from the wireless router main menu. Troubleshooting PPPoE To troubleshoot a PPPoE connection:

1. Log in to the wireless router. 2. Select Router Status under Maintenance on the main menu. 3. Click the Connection Status button. 4. 5. If all the steps indicate OK, then your PPPoE connection is up and working. If any of the steps indicate Failed, you can attempt to reconnect by clicking Connect. The wireless router will continue to attempt to connect indefinitely. If you cannot connect after several minutes, you might be using an incorrect service name, user name, or password. There also might be a provisioning problem with your ISP. Unless you connect manually, the wireless router will not authenticate using PPPoE until data is transmitted to the network. Troubleshooting Internet Browsing If your wireless router can obtain an IP address but your computer is unable to load any Web pages from the Internet, check the following. Your computer might not recognize any DNS server addresses. A DNS server is a host on the Internet that translates Internet names (such as www addresses) to numeric IP addresses. Typically your ISP provides the addresses of one or two DNS servers for your use. If you entered a DNS address when you configured the wireless router, restart your computer. Alternatively, you can configure your computer manually with DNS addresses, as explained in the documentation for your computer. Your computer might not have the wireless router configured as its default gateway. Help with Troubleshooting 25 v1.0, November 2007 Wireless Router Setup Manual Restart the computer, and verify that the wireless router address (192.168.1.1) is listed by your computer as the default gateway address. The factory default wireless router address is 192.168.1.1. However, if the router detects a conflict with the address it gets from your modem, it automatically picks a different address for itself. In this case, you can log in to the router using www.routerlogin.net to verify its LAN IP address. Select LAN IP Setup under Advanced on the main menu. Take note of the LAN TCP/IP setup IP address, which should match the default gateway IP address on your computer. Troubleshooting Connectivity Using the Ping Utility Most computers and routers have a diagnostic utility called ping that sends an request to a target device. The device then replies. The ping utility makes it easy to troubleshoot a network.. This section includes advanced troubleshooting techniques. Testing the Path from a PC to Your Router You can ping the wireless router to verify that the LAN path from your computer to your router is set up correctly. 1. From the Windows toolbar, click Start and select Run. 2. In the field provided, type Ping followed by the address of the router, as in this example:

ping www.routerlogin.net or ping 192.168.1.1 3. Click OK. You should see a message like this one:

Pinging 192.168.1.1 with 32 bytes of data If the path is working, you see this message:

Reply from 192.168.1.1: bytes=32 time=NN ms TTL=xxx If the path is not working, you see this message:

26 Help with Troubleshooting v1.0, November 2007 Wireless Router Setup Manual Request timed out If the path is not functioning correctly, you could have one of the following problems:

Wrong physical connections Make sure that the LAN port light is on. If the light is off, follow the instructions in If the LAN or Internet port lights are not on when the Ethernet connection is made: on page 23. Check that the corresponding lights are on for your computers network interface card. Wrong network configuration Verify that the Ethernet card driver software and TCP/IP software are both installed and configured on your computer. Verify that the IP address for your router and your computer are correct and that the addresses on both begin with 255.255.255.0. Testing the Path from a PC to the Internet After verifying that the path between your computer and the wireless router works correctly, test the path from your PC to the Internet. From the Windows Start > Run... menu, type:

PING -n 10 <IP address>

where <IP address> is the IP address of a remote device such as your ISPs DNS server. If the path is functioning correctly, replies as in the previous section are displayed. If you do not receive replies:

Check that your PC has the IP address of your router listed as the default gateway. If the IP configuration of your PC is assigned by DHCP, this information is not visible in your PCs Network Control Panel. Verify that the IP address of the router is listed as the TCP/IP default gateway. Check to see that the network address of your PC (the portion of the IP address specified by the netmask) is different from the network address of the remote device. If your ISP assigned a host name to your PC, enter that host name as the account name in the Basic Settings screen. Help with Troubleshooting 27 v1.0, November 2007 Wireless Router Setup Manual 28 Help with Troubleshooting v1.0, November 2007 Default Configuration Default Configuration Settings This section provides factory default settings and technical specifications for the RangeMax Dual Band Wireless-N Router WNDR3300. Table 2. Wireless Router Default Configuration Settings Feature Smart Wizard Router Login Router Login URL Login name (case-sensitive) printed on product label Login password (case-sensitive) printed on product label Internet Connection WAN MAC Address MTU Size Local Network Default Setting Enabled http://www. routerlogin.net or http://www.routerlogin.com admin password Use default hardware address 1500 Router Lan IP address printed on product label (also known as modem IP address) Router Subnet DHCP Server Time Zone Time Zone Adjusted for Daylight Saving Time 192.168.1.1 255.255.255.0 Enabled Pacific Time Disabled Default Configuration 29 v1.0, November 2007 Wireless Router Setup Manual Table 2. Wireless Router Default Configuration Settings (continued) Feature Firewall Default Setting Inbound (communications coming in from the Internet) Outbound (communications going out to the Internet) Disabled (bars all unsolicited requests) Enabled (all) Wireless Wireless Communication SSID Name Security Broadcast SSID Transmission Speed Country/Region RF Channel Operating Mode Data Rate Output Power Enabled NETGEAR Disabled Enabled Autoa United States in the US, otherwise varies by region 6 until region selected Mode 1. 802.11n 2.4G mode Mode 2. 802.11n 5G + Legacy 802.11g at 2.4G Best Full a. Maximum Wireless signal rate derived from IEEE Standard 802.11 specifications. Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead lower actual data throughput rate. Network Protocol and Standards Compatibility Data and Routing Protocols:

Power Adapter North America:

United Kingdom, Australia:

Europe:

Japan:

All regions (output):

TCP/IP, RIP-1, RIP-2, DHCP PPP over Ethernet (PPPoE) 120V, 60 Hz, input 240V, 50 Hz, input 230V, 50 Hz, input 100V, 50/60 Hz, input 12 V DC @ 1.5A output, 18W maximum 30 Default Configuration v1.0, November 2007 Table 2. Wireless Router Default Configuration Settings (continued) Wireless Router Setup Manual Feature Physical Specifications Dimensions:

Weight:

Environmental Specifications Operating temperature:

Operating humidity:

Electromagnetic Emissions Meets requirements of:

Interface Specifications LAN:

WAN:

Wireless:

Radio Data Rates:

Frequency Data Encoding:

Maximum Computers Per Wireless Network:

Operating Frequency Ranges (2.4G):

Default Setting 28 x 175 x 119 mm (1.1 x 6.89 x 4.68 in.) 0.5 kg (1.2 lb) 0 to 40 C (32 to 104 F) 90% maximum relative humidity, noncondensing FCC Part 15 Class B VCCI Class B EN 55 022 (CISPR 22), Class B C-Tick N10947 10BASE-T or 100BASE-Tx, RJ-45 10BASE-T or 100BASE-Tx, RJ-45 Maximum wireless signal rate complies with the IEEE 802.11 standard. Actual throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Auto Rate Sensing 2.4 Ghz & 5 Ghz Standards IEEE 802.11n draft version 1.0 IEEE 802.11n, IEEE 802.11g, IEEE 802.11b 2.4 GHz IEEE 802.11n, IEEE 802.11g 5.0 GHz Limited by the amount of wireless network traffic generated by each node. Typically 30-70 nodes. 2.4122.462 GHz (US) 2.4122.472 GHz (Japan) 2.4122.472 GHz (Europe ETSI) Default Configuration 31 v1.0, November 2007 Wireless Router Setup Manual Table 2. Wireless Router Default Configuration Settings (continued) Feature Operating Frequency Ranges (5G):

802.11 Security:

Default Setting 5.185.24 + 5.7455.825 GHz (US) 5.185.24 GHz (Europe ETSI) 40-bit (also called 64-bit) and 128-bit WEP, WPA-

PSK and WPA2-PSK. Restoring the Default Password and Configuration Settings You can restore the factory default configuration settings that reset the routers user name to admin, the password to password, and the IP address to 192.168.1.1. This procedure will erase all the current configuration settings and restore the factory defaults. To restore the factory default configuration settings:

1. Use a sharp object such as a pen or a paper clip to press and hold the restore factory settings button, located on the rear panel of the router, for about 20 seconds, until the Power light begins to blink (see Router Back Panel on page 5). 2. Release the restore factory settings button, and wait for the router to restart, and for the Power light to stop blinking and become solid green. The factory default settings will be restored so that you can access the router from your Web browser using the factory defaults. 32 Default Configuration v1.0, November 2007 Related Documents This table provides links to reference documents that you can use to gain a more complete understanding of the technologies used in your NETGEAR product. Table 3. Reference Documents Link Document TCP/IP Networking Basics Preparing Your Network http://documentation.netgear.com/reference/enu/wsdhcp/index.htm http://documentation.netgear.com/reference/enu/glossary/index.htm Glossary http://documentation.netgear.com/reference/enu/tcpip/index.htm Related Documents 33 v1.0, November 2007 Wireless Router Setup Manual 34 Related Documents v1.0, November 2007 Registration and Certifications Product Registration, Support, and Documentation Register your product at http://www.NETGEAR.com/register. You must register before you can use our telephone support service. Product updates and Web support are always available by going to http://www.netgear.com/support. Setup documentation is available on the CD, on the support website, and on the documentation website. When the wireless router is connected to the Internet, click the KnowledgeBase link to view support information, or click the Documentation link to view the online Reference Manual for this wireless router. Maximum Wireless Signal Rate Derived from IEEE Standard 802.11 Specifications Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and network overhead, lower actual data throughput rate. Federal Communications Commission (FCC) Compliance Notice: Radio Frequency Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

This transmitter is restricted to indoor use only within the 5.15-5.25 GHz band. Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 35 FCC Statement:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. CE Statement:

Hereby, NETGEAR, declares that this device is in compliance with the essential requirement and other relevant provisions of the R&TTE Driective 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Luxembourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slovenia Bulgaria, Romania. 36